Search results for: power loss cost

Authors: Belen Montero, Carmen Ramirez, Maite Rico, Rebeca Bouza, Irene Derungs

Abstract:

Starch is a promising polymer for producing biocomposite materials because it is renewable, completely biodegradable and easily available at a low cost. Thermoplastic starches (TPS) can be obtained after the disruption and plasticization of native starch with a plasticizer. In this work, the solvent casting method was used to obtain TPS films from wheat starch plasticized with glycerol and reinforced with nanocellulose (CNC). X-ray diffraction analysis was used to follow the evolution of the crystallinity. The native wheat starch granules have shown a profile corresponding to A-type crystal structures typical for cereal starches. When TPS films are analyzed a high amorphous halo centered on 19º is obtained, indicating the plasticization process is completed. SEM imaging was made in order to analyse the morphology. The image from the raw wheat starch granules shows a bimodal granule size distribution with some granules in large round disk-shape forms (A-type) and the others as smaller spherical particles (B-type). The image from the neat TPS surface shows a continuous surface. No starch aggregates or swollen granules can be seen so, the plasticization process is complete. In the surfaces of reinforced TPS films aggregates are seen as the CNC concentration in the matrix increases. The CNC influence on the mechanical properties of TPS films has been studied by dynamic mechanical analysis. A direct relation exists between the storage modulus values, E’, and the CNC content in reinforced TPS films: higher is the content of nanocellulose in the composite, higher is the value of E’. This reinforcement effect can be explained by the appearance of a strong and crystalline nanoparticle-TPS interphase. Thermal stability of films was analysed by TGA. It has not observed any influence on the behaviour related to the thermal degradation of films with the incorporation of the CNC. Finally, the resistance to the water absorption films was analysed following the standard UNE-EN ISO 1998:483. The percentage of water absorbed by the samples at each time was calculated. The addition of 5 wt % of CNC to the TPS matrix leads to a significant improvement in the moisture resistance of the starch based material decreasing their diffusivity. It has been associated to the formation of a nanocrystal network that prevents swelling of the starch and therefore water absorption and to the high crystallinity of cellulose compared to starch. As a conclusion, the wheat film reinforced with 5 wt % of cellulose nanocrystals seems to be a good alternative for short-life applications into the packaging industry, because of its greatest rigidity, thermal stability and moisture sorption resistance.

Keywords: biocomposites, nanocellulose, starch, wheat

Procedia PDF Downloads 205

Authors: Venkata Buddharaju, Irene Mccarron, Hazel Alba

Abstract:

Introduction: Male external catheters (MECs) are commonly used to collect and drain urine. MECs are increasingly used in acute care, long-term acute care hospitals, and nursing facilities, and in other patients as an alternative to invasive urinary catheters to reduce catheter-associated urinary tract infections (CAUTI).MECs are also used to avoid the need for incontinence pads and diapers. Most of the Male External Catheters are held in place by skin adhesive, with the exception of a few, which uses a foam strap clamp around the penile shaft. The adhesive condom catheters typically stay for 24 hours or less. It is also a common practice that extra skin adhesive tape is wrapped around the condom catheter for additional security of the device. The fixed nature of the adhesive will not allow the normal skin expansion of penile size over time. The adhesive can cause skin irritation, redness, erosion, and skin damage. Acanthus condom catheter (ACC) is a patented, specially designed, stretchable silicone catheter without adhesive, adapts to the size and contour of the penis. It is held in place with a single elastic strap that wraps around the lower back and tied to the opposite catheter ring holescriss cross. It can be reused for up to 5 days on the same patient after daily cleaning and washingpotentially reducing cost. Methods: The study was conducted from September 17th to October 8th, 2020. The nursing staff was educated and trained on how to use and reuse the catheter. After identifying five (5) appropriate patients, the catheter was placed and maintained by nursing staff. The data on the ease of use, leak, and skin damage were collected and reported by nurses to the nursing education department of the hospital for analysis. Setting: RML Chicago, long-term acute care hospital, an affiliate of Loyola University Medical Center, Chicago, IL USA. Results: The data showed that the catheter was easy to apply, remove, wash and reuse, without skin problems or urine infections. One patient had used for 16 days after wash, reuse, and replacement without any urine leak or skin issues. A minimal leak was observed on two patients. Conclusion: Acanthus condom catheter was easy to use, functioned well with minimal or no leak during use and reuse. The skin was intact in all patients studied. There were no urinary tract infections in any of the studied patients.

Keywords: CAUTI, male external catheter, reusable, skin adhesive

Procedia PDF Downloads 101

Authors: Mohsen Rabbani, Trista McLaughlin, Ehsan Vahidi

Abstract:

the remediation of polluted sites with heavy metals, such as rare earth elements (REEs), has been a primary concern of researchers to decontaminate the soil. Among all developed methods to address this concern, phytoremediation has been established as efficient, cost-effective, easy-to-use, and environmentally friendly way, providing a long-term solution for addressing this global concern. Furthermore, this technology has another great potential application in the metals production sector through returning metals buried in soil via metals cropping. Considering the significant metal concentration in hyper-accumulators, the utilization of bioaccumulated metals to extract metals from plant matter has been proposed as a sub-economic area called phytomining. As a recent, more advanced technology to eliminate such pollutants from the soil and produce critical metals, bioharvesting (phytomining/agromining) has been considered another compromising way to produce metals and meet the global demand for critical/target metals. The bio-ore obtained from phytomining can be safely disposed of or introduced to metal production pathways to obtain the most demanded metals, such as REEs. It is well-known that some hyperaccumulators, e.g., fern Dicranopteris linearis, can be used to absorb REE metals from the polluted soils and accumulate them in plant organs, such as leaves and stems. After soil remediation, the plant species can be harvested and introduced to the downstream steps, namely crushing/grinding, leaching, and purification processes, to extract REEs from plant matter. This novel interdisciplinary field can fill the gap between agriculture, mining, metallurgy, and the environment. Despite the advantages of agromining for the REEs production industry, key issues related to the environmental sustainability of the entire life cycle of this new concept have not been assessed yet. Hence, a comparative life cycle assessment (LCA) study was conducted to quantify the environmental footprints of REEs phytomining. The current LCA study aims to estimate and calculate environmental effects associated with phytomining by considering critical factors, such as climate change, land use, and ozone depletion. The results revealed that phytomining is an easy-to-use and environmentally sustainable approach to either eliminate REEs from polluted sites or produce REEs, offering a new source of such metals production. This LCA research provides guidelines for researchers active in developing a reliable relationship between agriculture, mining, metallurgy, and the environment to encounter soil pollution and keep the earth green and clean.

Keywords: phytoremediation, phytomining, life cycle assessment, environmental impacts, rare earth elements, hyperaccumulator

Procedia PDF Downloads 66

Authors: Daphne Sobolev, Niklas Voege

Abstract:

During the last three decades, consumer ethics perceptions have attracted the attention of a large number of researchers. Nevertheless, little is known about the effect of the cognitive and situational contexts of the decision on ethics judgments. In this paper, the interrelationship between consumers’ ethics perceptions, legality evaluations and mind-sets are explored. Legality evaluations represent the cognitive context of the ethical judgments, whereas mind-sets represent their situational context. Drawing on moral development theories and priming theories, it is hypothesized that both factors are significantly related to consumer ethics perceptions. To test this hypothesis, 289 participants were allocated to three mind-set experimental conditions and a control group. Participants in the mind-set conditions were primed for aggressiveness, politeness or awareness to the negative legal consequences of breaking the law. Mind-sets were induced using a sentence-unscrambling task, in which target words were included. Ethics and legality judgments were assessed using consumer ethics and internet ethics questionnaires. All participants were asked to rate the ethicality and legality of consumer actions described in the questionnaires. The results showed that consumer ethics and legality perceptions were significantly correlated. Moreover, including legality evaluations as a variable in ethics judgment models increased the predictive power of the models. In addition, inducing aggressiveness in participants reduced their sensitivity to ethical issues; priming awareness to negative legal consequences increased their sensitivity to ethics when uncertainty about the legality of the judged scenario was high. Furthermore, the correlation between ethics and legality judgments was significant overall mind-set conditions. However, the results revealed conflicts between ethics and legality perceptions: consumers considered 10%-14% of the presented behaviors unethical and legal, or ethical and illegal. In 10-23% of the questions, participants indicated that they did not know whether the described action was legal or not. In addition, an asymmetry between the effects of aggressiveness and politeness priming was found. The results show that the legality judgments and mind-sets interact with consumer ethics perceptions. Thus, they portray consumer ethical judgments as dynamical processes which are inseparable from other cognitive processes and situational variables. They highlight that legal and ethical education, as well as adequate situational cues at the service place, could have a positive effect on consumer ethics perceptions. Theoretical contribution is discussed.

Keywords: consumer ethics, legality judgments, mind-set, priming, aggressiveness

Procedia PDF Downloads 291

Authors: Muhammad Umar Usman

Abstract:

This study investigates the entrepreneurial intentions, drivers and challenges of starting a business among final year students in Jigawa State polytechnic. Nigeria. Final year students of Jigawa State Polytechnic from the department of accounting, business administration and management and public administration were used as a case study. The study became necessary due to the alarming rate of graduate unemployment in Nigeria. The study adopted a holistic case study approach involving a multiple methods of questionnaires involving (182) Higher National Diploma (HND) and National Diploma (ND) final year students and a telephone interview with two lecturers teaching entrepreneurship in the college. The findings clearly indicate that exposer to entrepreneurship education increases students’ entrepreneurial intentions. The result found that desire for independence, confidence and strong intention are the most important factors that influence students’ entrepreneurial intention. The study identified 3 key drivers of students’ entrepreneurial intentions. These are to earn a living, to seek job security and provision of employment. The result again identified 4 factors namely lack of support, finance, insecurity and erratic power supply as the major challenges in starting a business in Nigeria. It was also revealed that the current entrepreneurship education programme prepares students on how to open up a business not becoming an entrepreneur. The study concluded entrepreneurship helps students toward building and driving their intention to venture into business. However, the challenges of entrepreneurship in Nigeria need to be addressed in order to enable individuals to become an entrepreneur and create employment opportunities that will lead to the development of Nigerian economy. Thus, the government should provide adequate support particularly the issue of infrastructures. The Federal Government of Nigeria in collaboration with the National Board for Technical Education should fashion out the curriculum thereby making it more practically-oriented so that students may become more interested. Polytechnics should develop an internship programme for students to work in firms so as to put theory learnt in the class to practice. Students should try to align the theory learnt in college with the practical application in dynamic economic environment. Hence, this will help in building their capabilities toward entrepreneurship development in Nigeria.

Keywords: entrepreneurial intention, entrepreneurial drivers, challenges, entrepreneurial education

Procedia PDF Downloads 293

Authors: Amit Gill, Lalith Wijerathne, Sebastian Poledna

Abstract:

This research presents the details of the implementation of high performance computing (HPC) extension of agent-based economic models (ABEMs) to simulate hundreds of millions of heterogeneous agents. ABEMs offer an alternative approach to study the economy as a dynamic system of interacting heterogeneous agents, and are gaining popularity as an alternative to standard economic models. Over the last decade, ABEMs have been increasingly applied to study various problems related to monetary policy, bank regulations, etc. When it comes to predicting the effects of local economic disruptions, like major disasters, changes in policies, exogenous shocks, etc., on the economy of the country or the region, it is pertinent to study how the disruptions cascade through every single economic entity affecting its decisions and interactions, and eventually affect the economic macro parameters. However, such simulations with hundreds of millions of agents are hindered by the lack of HPC enhanced ABEMs. In order to address this, a scalable Distributed Memory Parallel (DMP) implementation of ABEMs has been developed using message passing interface (MPI). A balanced distribution of computational load among MPI-processes (i.e. CPU cores) of computer clusters while taking all the interactions among agents into account is a major challenge for scalable DMP implementations. Economic agents interact on several random graphs, some of which are centralized (e.g. credit networks, etc.) whereas others are dense with random links (e.g. consumption markets, etc.). The agents are partitioned into mutually-exclusive subsets based on a representative employer-employee interaction graph, while the remaining graphs are made available at a minimum communication cost. To minimize the number of communications among MPI processes, real-life solutions like the introduction of recruitment agencies, sales outlets, local banks, and local branches of government in each MPI-process, are adopted. Efficient communication among MPI-processes is achieved by combining MPI derived data types with the new features of the latest MPI functions. Most of the communications are overlapped with computations, thereby significantly reducing the communication overhead. The current implementation is capable of simulating a small open economy. As an example, a single time step of a 1:1 scale model of Austria (i.e. about 9 million inhabitants and 600,000 businesses) can be simulated in 15 seconds. The implementation is further being enhanced to simulate 1:1 model of Euro-zone (i.e. 322 million agents).

Keywords: agent-based economic model, high performance computing, MPI-communication, MPI-process

Procedia PDF Downloads 121

Authors: Selcen Nur Eri̇kci̇ Çeli̇k, Burcu İbaş Parlakyildiz, Gülay Zorer Gedi̇k

Abstract:

Reducing the use of mechanical heating and cooling systems in buildings, which accounts for approximately 30-40% of total energy consumption in the world has a major impact in terms of energy conservation. Formations of buildings that have sustainable and low energy utilization, structural elements with mechanical systems should be evaluated with a holistic approach. In point of reduction of building energy consumption ratio, wall elements that are vertical building elements and have an area broadly (m2) have proposed as a regulation with a different system. In the study, designing surface heating and cooling energy with a hybrid type of modular wall system and the integration of building elements will be evaluated. The design of wall element; - Identification of certain standards in terms of architectural design and size, -Elaboration according to the area where the wall elements (interior walls, exterior walls) -Solution of the joints, -Obtaining the surface in terms of building compatible with both conceptual structural put emphasis on upper stages, these elements will be formed. The durability of the product to the various forces, stability and resistance are so much substantial that are used the establishment of ready-wall element section and the planning of structural design. All created ready-wall alternatives will be paid attention at some parameters; such as adapting to performance-cost by optimum level and size that can be easily processed and reached. The restrictions such as the size of the zoning regulations, building function, structural system, wheelbase that are imposed by building laws, should be evaluated. The building aims to intend to function according to a certain standardization system and construction of wall elements will be used. The scope of performance criteria determined on the wall elements, utilization (operation, maintenance) and renovation phase, alternative material options will be evaluated with interim materials located in the contents. Design, implementation and technical combination of modular wall elements in the use phase and installation details together with the integration of energy saving, heat-saving and useful effects on the environmental aspects will be discussed in detail. As a result, the ready-wall product with surface heating and cooling modules will be created and defined as hybrid wall and will be compared with the conventional system in terms of thermal comfort. After preliminary architectural evaluations, certain decisions for all architectural design processes (pre and post design) such as the implementation and performance in use, maintenance, renewal will be evaluated in the results.

Keywords: modular ready-wall element, hybrid, architectural design, thermal comfort, energy saving

Procedia PDF Downloads 250

Authors: I. Nitoi, P. Oancea, M. Raileanu, M. Crisan, L. Constantin, I. Cristea

Abstract:

Hazardous organic compounds like nitroaromatics are frequently found in chemical and petroleum industries discharged effluents. Due to their bio-refractory character and high chemical stability cannot be efficiently removed by classical biological or physical-chemical treatment processes. In the past decades, semiconductor photocatalysis has been frequently applied for the advanced degradation of toxic pollutants. Among various semiconductors titania was a widely studied photocatalyst, due to its chemical inertness, low cost, photostability and nontoxicity. In order to improve optical absorption and photocatalytic activity of TiO2 many attempts have been made, one feasible approach consists of doping oxide semiconductor with metal. The degradation of dinitrobenzene (DNB) and dinitrotoluene (DNT) from aqueous solution under UVA-VIS irradiation using heavy metal (0.5% Fe, 1%Co, 1%Ni ) doped titania was investigated. The photodegradation experiments were carried out using a Heraeus laboratory scale UV-VIS reactor equipped with a medium-pressure mercury lamp which emits in the range: 320-500 nm. Solutions with (0.34-3.14) x 10-4 M pollutant content were photo-oxidized in the following working conditions: pH = 5-9; photocatalyst dose = 200 mg/L; irradiation time = 30 – 240 minutes. Prior to irradiation, the photocatalyst powder was added to the samples, and solutions were bubbled with air (50 L/hour), in the dark, for 30 min. Dopant type, pH, structure and initial pollutant concentration influence on the degradation efficiency were evaluated in order to set up the optimal working conditions which assure substrate advanced degradation. The kinetics of nitroaromatics degradation and organic nitrogen mineralization was assessed and pseudo-first order rate constants were calculated. Fe doped photocatalyst with lowest metal content (0.5 wt.%) showed a considerable better behaviour in respect to pollutant degradation than Co and Ni (1wt.%) doped titania catalysts. For the same working conditions, degradation efficiency was higher for DNT than DNB in accordance with their calculated adsobance constants (Kad), taking into account that degradation process occurs on catalyst surface following a Langmuir-Hinshalwood model. The presence of methyl group in the structure of DNT allows its degradation by oxidative and reductive pathways, while DNB is converted only by reductive route, which also explain the highest DNT degradation efficiency. For highest pollutant concentration tested (3 x 10-4 M), optimum working conditions (0.5 wt.% Fe doped –TiO2 loading of 200 mg/L, pH=7 and 240 min. irradiation time) assures advanced nitroaromatics degradation (ηDNB=89%, ηDNT=94%) and organic nitrogen mineralization (ηDNB=44%, ηDNT=47%).

Keywords: hazardous organic compounds, irradiation, nitroaromatics, photocatalysis

Procedia PDF Downloads 313

Authors: K. Tunde Olagunju, C. Scott Allen, Freek Van Der Meer

Abstract:

Identification of hydrocarbon oil in remote sensing images is often the first step in monitoring oil during spill events. Most remote sensing methods adopt techniques for hydrocarbon identification to achieve detection in order to model an appropriate cleanup program. Identification on optical sensors does not only allow for detection but also for characterization and quantification. Until recently, in optical remote sensing, quantification and characterization are only potentially possible using high-resolution laboratory and airborne imaging spectrometers (hyperspectral data). Unlike multispectral, hyperspectral data are not freely available, as this data category is mainly obtained via airborne survey at present. In this research, two (2) operational high-resolution multispectral satellites (WorldView-3 and Sentinel-2) are theoretically assessed for their suitability for hydrocarbon characterization, using the hydrocarbon spectral slope model (HYSS). This method utilized the two most persistent hydrocarbon diagnostic/absorption features at 1.73 µm and 2.30 µm for hydrocarbon mapping on multispectral data. In this research, spectra measurement of seven (7) different hydrocarbon oils (crude and refined oil) taken on ten (10) different substrates with the use of laboratory ASD Fieldspec were convolved to Sentinel-2 and WorldView-3 resolution, using their full width half maximum (FWHM) parameter. The resulting hydrocarbon slope values obtained from the studied samples enable clear qualitative discrimination of most hydrocarbons, despite the presence of different background substrates, particularly on WorldView-3. Due to close conformity of central wavelengths and narrow bandwidths to key hydrocarbon bands used in HYSS, the statistical significance for qualitative analysis on WorldView-3 sensors for all studied hydrocarbon oil returned with 95% confidence level (P-value ˂ 0.01), except for Diesel. Using multifactor analysis of variance (MANOVA), the discriminating power of HYSS is statistically significant for most hydrocarbon-substrate combinations on Sentinel-2 and WorldView-3 FWHM, revealing the potential of these two operational multispectral sensors as rapid response tools for hydrocarbon mapping. One notable exception is highly transmissive hydrocarbons on Sentinel-2 data due to the non-conformity of spectral bands with key hydrocarbon absorptions and the relatively coarse bandwidth (> 100 nm).

Keywords: hydrocarbon, oil spill, remote sensing, hyperspectral, multispectral, hydrocarbon-substrate combination, Sentinel-2, WorldView-3

Procedia PDF Downloads 212

Authors: Ashi Gautam, Isha Shukla, Akhil Seghal

Abstract:

Biosensors are analytical devices that use a biological sensing element to detect and measure a specific chemical substance or biomolecule in a sample. These devices are widely used in various fields, including medical diagnostics, environmental monitoring, and food analysis, due to their high specificity, sensitivity, and selectivity. In this research paper, a machine learning model is proposed for predicting the suitability of skin care products based on biosensor readings. The proposed model takes in features extracted from biosensor readings, such as biomarker concentration, skin hydration level, inflammation presence, sensitivity, and free radicals, and outputs the most appropriate skin care product for an individual. This model is trained on a dataset of biosensor readings and corresponding skin care product information. The model's performance is evaluated using several metrics, including accuracy, precision, recall, and F1 score. The aim of this research is to develop a personalised skin care product recommendation system using biosensor data. By leveraging the power of machine learning, the proposed model can accurately predict the most suitable skin care product for an individual based on their biosensor readings. This is particularly useful in the skin care industry, where personalised recommendations can lead to better outcomes for consumers. The developed model is based on supervised learning, which means that it is trained on a labeled dataset of biosensor readings and corresponding skin care product information. The model uses these labeled data to learn patterns and relationships between the biosensor readings and skin care products. Once trained, the model can predict the most suitable skin care product for an individual based on their biosensor readings. The results of this study show that the proposed machine learning model can accurately predict the most appropriate skin care product for an individual based on their biosensor readings. The evaluation metrics used in this study demonstrate the effectiveness of the model in predicting skin care products. This model has significant potential for practical use in the skin care industry for personalised skin care product recommendations. The proposed machine learning model for predicting the suitability of skin care products based on biosensor readings is a promising development in the skin care industry. The model's ability to accurately predict the most appropriate skin care product for an individual based on their biosensor readings can lead to better outcomes for consumers. Further research can be done to improve the model's accuracy and effectiveness.

Keywords: biosensors, data model, machine learning, skin care

Procedia PDF Downloads 88

Authors: Yuri Melis, Mattia Resteghini, Emanuela Apicella, Eugenia Dozio, Leonardo Mendolicchio

Abstract:

Aim: This retrospective study was created to analyze the psychometric, anthropometric and body composition values in patients at the beginning and the discharge of their of hospitalization in the residential care clinic for eating and feeding disorders (EFD’s). Method: The sample was composed by (N=59) patients with mean age N= 33,50, divided in subgroups: Anorexia Nervosa (AN) (N=28), Bulimia Nervosa (BN) (N=13) and Binge Eating Disorders (BED) (N=14) recruited from a residential care clinic for eating and feeding disorders. The psychometrics level was measured with self-report questionnaires: Eating Disorders Inventory-3 (EDI-3) The Body Uneasiness Test (BUT), Minnesota Multiphasic Personality Inventory (MMPI – 2). The anthropometric and nutritional values was collected by Body Impedance Assessment (B.I.A), Body mass index (B.M.I.). Measurements were made at the beginning and at the end of hospitalization, with an average time of recovery of about 8,6 months. Results: The all data analysis showed a statistical significance (p-value >0,05 | power size N=0,950) in variation from T0 (start of recovery) to T1 (end of recovery) in the clinical scales of MMPI-2, AN group (Hypocondria T0 64,14 – T1 56,39) (Depression T0 72,93 – T1 59,50) (Hysteria T0 61,29 – T1 56,17) (Psychopathic deviation T0 64,00 – T1 60,82) (Paranoia T0 63,82 – T1 56,14) (Psychasthenia T0 63,82 – T1 57,86) (Schizophrenia T0 64,68 – T1 60,43) (Obsessive T0 60,36 – T1 55,68); BN group (Hypocondria T0 64,08 – T1 47,54) (Depression T0 67,46 – T1 52,46) (Hysteria T0 60,62 – T1 47,84) (Psychopathic deviation T0 65,69 – T1 58,92) (Paranoia T0 67,46 – T1 55,23) (Psychasthenia T0 60,77 – T1 53,77) (Schizophrenia T0 64,68 – T1 60,43) (Obsessive T0 62,92 – T1 54,08); B.E.D groups (Hypocondria T0 59,43 – T1 53,14) (Depression T0 66,71 – T1 54,57) (Hysteria T0 59,86 – T1 53,82) (Psychopathic deviation T0 67,39 – T1 59,03) (Paranoia T0 58,57 – T1 53,21) (Psychasthenia T0 61,43 – T1 53,00) (Schizophrenia T0 62,29 – T1 56,36) (Obsessive T0 58,57 – T1 48,64). EDI-3 report mean value is higher than clinical cut-off at T0, in T1, there is a significant reduction of the general mean of value. The same result is present in the B.U.T. test in the difference between T0 to T1. B.M.I mean value in AN group is (T0 14,83 – T1 18,41) BN group (T0 20 – T1 21,33) BED group (T0 42,32 – T1 34,97) Phase Angle results: AN group (T0 4,78 – T1 5,64) BN (T0 6 – T1 6,53) BED group (T0 6 – T1 6,72). Discussion and conclusion: The evident presence that on the whole sample, we have an altered serious psychiatric and clinic conditions at the beginning of recovery. The interesting conclusions that we can draw from this analysis are that a multidisciplinary approach that includes the entire care of the subject: from the pharmacological treatment, analytical psychotherapy, Psychomotricity, nutritional rehabilitation, and rehabilitative, educational activities. Thus, this Multidisciplinary treatment allows subjects in our sample to be able to restore psychopathological and metabolic values to below the clinical cut-off.

Keywords: feeding and eating disorders, anorexia nervosa, care clinic treatment, multidisciplinary treatment

Procedia PDF Downloads 120

Authors: Dilek Ozturk, Narin Ozturk, Zeliha Pala Kara, Engin Kaptan, Serap Sancar Bas, Nurten Ozsoy, Alper Okyar

Abstract:

Most physiological processes oscillate in a rhythmic manner in mammals including metabolism and energy homeostasis, locomotor activity, hormone secretion, immune and endocrine system functions. Endocrine body rhythms are tightly regulated by the circadian timing system. The hypothalamic-pituitary-thyroid (HPT) axis is under circadian control at multiple levels from hypothalamus to thyroid gland. Since circadian timing system controls a variety of biological functions in mammals, circadian rhythms of biological functions may modify the drug tolerability/toxicity depending on the dosing time. Selective mTOR (mammalian target of rapamycin) inhibitor everolimus is an immunosuppressant and anticancer agent that is active against many cancers. It was also found to be active in medullary thyroid cancer. The aim of this study was to investigate the dosing time-dependent toxicity of everolimus on the thyroid gland and hormones in mice. Healthy C57BL/6J mice were synchronized with 12h:12h Light-Dark cycle (LD12:12, with Zeitgeber Time 0 – ZT0 – corresponding to Light onset). Everolimus was administered to male (5 mg/kg/day) and female mice (15 mg/kg/day) orally at ZT1-rest period- and ZT13-activity period- for 4 weeks; body weight loss, clinical signs and possible changes in serum thyroid hormone levels (TSH and free T4) were examined. Histological alterations in the thyroid gland were evaluated according to the following criteria: follicular size, colloid density and viscidity, height of the follicular epithelium and the presence of necrotic cells. The statistical significance between differences was analyzed with ANOVA. Study findings included everolimus-related diarrhea, decreased activity, decreased body weight gains, alterations in serum TSH levels, and histopathological changes in thyroid gland. Decreases in mean body weight gains were more evident in mice treated at ZT1 as compared to ZT13 (p < 0.001, for both sexes). Control tissue sections of thyroid glands exhibited well-organized histoarchitecture when compared to everolimus-treated groups. Everolimus caused histopathological alterations in thyroid glands in male (5 mg/kg, slightly) and female mice (15 mg/kg; p < 0.01 for both ZT as compared to their controls) irrespective of dosing-time. TSH levels were slightly decreased upon everolimus treatment at ZT13 in both males and females. Conversely, increases in TSH levels were observed when everolimus treated at ZT1 in both males (5 mg/kg; p < 0.05) and females (15 mg/kg; slightly). No statistically significant alterations in serum free T4 levels were observed. TSH and free T4 is clinically important thyroid hormones since a number of disease states have been linked to alterations in these hormones. Serum free T4 levels within the normal ranges in the presence of abnormal serum TSH levels in everolimus treated mice may suggest subclinical thyroid disease which may have repercussions on the cardiovascular system, as well as on other organs and systems. Our study has revealed the histological damage on thyroid gland induced by subacute everolimus administration, this effect was irrespective of dosing time. However, based on the body weight changes and clinical signs upon everolimus treatment, tolerability for the drug was best following dosing at ZT13 in both male and females. Yet, effects of everolimus on thyroid functions may deserve further studies regarding their clinical importance and chronotoxicity.

Keywords: circadian rhythm, chronotoxicity, everolimus, thyroid gland, thyroid hormones

Procedia PDF Downloads 346

Authors: Antonis Skouloudis, Konstantinos Evangelinos, Walter Leal-Filho, Panagiotis Vouros, Ioannis Nikolaou

Abstract:

Organizational resilience capacity to extreme weather events (EWEs) has sparked a growth in scholarly attention over the past decade as an essential aspect in business continuity management, with supporting evidence for this claim to suggest that it retains a key role in successful responses to adverse situations, crises and shocks. Small and medium-sized enterprises (SMEs) are more vulnerable to face floods compared to their larger counterparts, so they are disproportionately affected by such extreme weather events. The limited resources at their disposal, the lack of time and skills all conduce to inadequate preparedness to challenges posed by floods. SMEs tend to plan in the short-term, reacting to circumstances as they arise and focussing on their very survival. Likewise, they share less formalised structures and codified policies while they are most usually owner-managed, resulting in a command-and-control management culture. Such characteristics result in them having limited opportunities to recover from flooding and quickly turnaround their operation from a loss making to a profit making one. Scholars frame the capacity of business entities to be resilient upon an EWE disturbance (such as flash floods) as the rate of recovery and restoration of organizational performance to pre-disturbance conditions, the amount of disturbance (i.e. threshold level) a business can absorb before losing structural and/or functional components that will alter or cease operation, as well as the extent to which the organization maintains its function (i.e. impact resistance) before performance levels are driven to zero. Nevertheless, while it seems to be accepted as an essential trait of firms effectively transcending uncertain conditions, research deconstructing the enabling conditions and/or inhibitory factors of SMEs resilience capacity to natural hazards is still sparse, fragmentary and mostly fuelled by anecdotal evidence or normative assumptions. Focusing on the individual level of analysis, i.e. the individual enterprise and its endeavours to succeed, the emergent picture from this relatively new research strand delineates the specification of variables, conceptual relationships or dynamic boundaries of resilience capacity components in an attempt to provide prescriptions for policy-making as well as business management. This study will present the development of a flood resilience capacity index (FRCI) and its application to Greek SMEs. The proposed composite indicator pertains to cognitive, behavioral/managerial and contextual factors that influence an enterprise’s ability to shape effective responses to meet flood challenges. Through the proposed indicator-based approach, an analytical framework is set forth that will help standardize such assessments with the overarching aim of reducing the vulnerability of SMEs to flooding. This will be achieved by identifying major internal and external attributes explaining resilience capacity which is particularly important given the limited resources these enterprises have and that they tend to be primary sources of vulnerabilities in supply chain networks, generating Single Points of Failure (SPOF).

Keywords: Floods, Small & Medium-Sized enterprises, organizational resilience capacity, index development

Procedia PDF Downloads 185

Authors: Jason Gica, Yi-Hsieng Samuel Wu, Deng-Jye Yang, Yi-Chen Chen

Abstract:

Mycotoxins, harmful secondary metabolites produced by certain fungi species, pose significant risks to animals and humans worldwide. Their stable properties lead to contamination during grain harvesting, transportation, and storage, as well as in processed food products. The prevalence of mycotoxin contamination has attracted significant attention due to its adverse impact on food safety and global trade. The secondary contamination pathway from animal products has been identified as an important route of exposure, posing health risks for livestock and humans consuming contaminated products. Pork, one of the highly consumed meat products in Taiwan according to the National Food Consumption Database, plays a critical role in the nation's diet and economy. Given its substantial consumption, pork processing products are a significant component of the food supply chain and a potential source of mycotoxin contamination. This study is paramount for formulating effective regulations and strategies to mitigate mycotoxin-related risks in the food supply chain. By establishing a reliable analytical method, this research contributes to safeguarding public health and enhancing the quality of pork processing products. The findings will serve as valuable guidance for policymakers, food industries, and consumers to ensure a safer food supply chain in the face of emerging mycotoxin challenges. An innovative and efficient analytical approach is proposed using Ultra-High Performance Liquid Chromatography coupled with Temperature Control Fluorescence Detector Light (UHPLC-TCFLD) to determine multiple mycotoxins in pork meat samples due to its exceptional capacity to detect multiple mycotoxins at the lowest levels of concentration, making it highly sensitive and reliable for comprehensive mycotoxin analysis. Additionally, its ability to simultaneously detect multiple mycotoxins in a single run significantly reduces the time and resources required for analysis, making it a cost-effective solution for monitoring mycotoxin contamination in pork processing products. The research aims to optimize the efficient mycotoxin QuEChERs extraction method and rigorously validate its accuracy and precision. The results will provide crucial insights into mycotoxin levels in pork processing products.

Keywords: multiple-mycotoxin analysis, pork processing products, QuEChERs, UHPLC-TCFLD, validation

Procedia PDF Downloads 58

Authors: M. Haruna, O. O. Onafowokan, G. Holt, K. Anderson, R. G. Middleton

Abstract:

Background: Requirements for satisfactory outcomes following total hip arthroplasty (THA) include restoration of femoral offset, version, and leg length. Various techniques have been described for restoring these biomechanical parameters, with leg length restoration being the most predominantly described. We describe a “quartered head technique” (QHT) which uses a stepwise series of femoral head osteotomies to identify and preserve the centre of rotation of the femoral head during THA in order to ensure reconstruction of leg length, offset and stem version, such that hip biomechanics are restored as near to normal as possible. This study aims to identify whether using the QHT during hip arthroplasty effectively restores leg length and femoral offset to within acceptable parameters. Methods: A retrospective review of 206 hips was carried out, leaving 124 hips in the final analysis. Power analysis indicated a minimum of 37 patients required. All operations were performed using an anterolateral approach by a single surgeon. All femoral implants were cemented, collarless, polished double taper CPT® stems (Zimmer, Swindon, UK). Both cemented, and uncemented acetabular components were used (Zimmer, Swindon, UK). Leg length, version, and offset were assessed intra-operatively and reproduced using the QHT. Post-operative leg length and femoral offset were determined and compared with the contralateral native hip, and the difference was then calculated. For the determination of leg length discrepancy (LLD), we used the method described by Williamson & Reckling, which has been shown to be reproducible with a measurement error of ±1mm. As a reference, the inferior margin of the acetabular teardrop and the most prominent point of the lesser trochanter were used. A discrepancy of less than 6mm LLD was chosen as acceptable. All peri-operative radiographs were assessed by two independent observers. Results: The mean absolute post-operative difference in leg length from the contralateral leg was +3.58mm. 84% of patients (104/124) had LLD within ±6mm of the contralateral limb. The mean absolute post-operative difference in offset from contralateral leg was +3.88mm (range -15 to +9mm, median 3mm). 90% of patients (112/124) were within ±6mm offset of the contralateral limb. There was no statistical difference noted between observer measurements. Conclusion: The QHT provides a simple, inexpensive yet effective method of maintaining femoral leg length and offset during total hip arthroplasty. Combining this technique with pre-operative templating or other techniques described may enable surgeons to reduce even further the discrepancies between pre-operative state and post-operative outcome.

Keywords: leg length discrepancy, technical tip, total hip arthroplasty, operative technique

Procedia PDF Downloads 75

Authors: Harneet Walia, Morteza Zihayat

Abstract:

Customer acquisition has become one of the critical issues of any business in the 21st century; having a healthy customer base is the essential asset of the bank business. Term deposits act as a major source of cheap funds for the banks to invest and benefit from interest rate arbitrage. To attract customers, the marketing campaigns at most financial institutions consist of multiple outbound telephonic calls with more than one contact to a customer which is a very time-consuming process. Therefore, customized direct marketing has become more critical than ever for attracting new clients. As customer acquisition is becoming more difficult to archive, having an intelligent and redefined list is necessary to sell a product smartly. Our aim of this research is to increase the effectiveness of campaigns by predicting customers who will most likely subscribe to the fixed deposit and suggest the most suitable month to reach out to customers. We design a Time Aware Upsell Prediction Framework (TAUPF) using two different approaches, with an aim to find the best approach and technique to build the prediction model. TAUPF is implemented using Upsell Prediction Approach (UPA) and Clustered Upsell Prediction Approach (CUPA). We also address the data imbalance problem by examining and comparing different methods of sampling (Up-sampling and down-sampling). Our results have shown building such a model is quite feasible and profitable for the financial institutions. The Time Aware Upsell Prediction Framework (TAUPF) can be easily used in any industry such as telecom, automobile, tourism, etc. where the TAUPF (Clustered Upsell Prediction Approach (CUPA) or Upsell Prediction Approach (UPA)) holds valid. In our case, CUPA books more reliable. As proven in our research, one of the most important challenges is to define measures which have enough predictive power as the subscription to a fixed deposit depends on highly ambiguous situations and cannot be easily isolated. While we have shown the practicality of time-aware upsell prediction model where financial institutions can benefit from contacting the customers at the specified month, further research needs to be done to understand the specific time of the day. In addition, a further empirical/pilot study on real live customer needs to be conducted to prove the effectiveness of the model in the real world.

Keywords: customer acquisition, predictive analysis, targeted marketing, time-aware analysis

Procedia PDF Downloads 116

Authors: Autumn Rooms Cypres, Barbara Driver

Abstract:

The purpose of this study is to extend discussions about innovations and career politics. Research questions that grounded this effort were: How does an academic learn the unspoken rules of the academy? What happens politically to an academic’s career when their research speaks against the grain of society? Do professors perceive signals that it is time to move on to another institution or even to another career? Epistemology and Methods: This qualitative investigation was focused on examining perceptions of academics. Therefore an open-ended field study, based on Grounded Theory, was used. This naturalistic paradigm (Lincoln & Guba,1985) was selected because it tends to understand information in terms of whole, of patterns, and in relations to the context of the environment. The technique for gathering data was the process of semi-structured, in-depth interviewing. Twenty five academics across the United States were interviewed relative to their career trajectories and the politics and opportunities they have encountered in relation to their research efforts. Findings: The analysis of interviews revealed four themes: Academics are beholden to 2 specific networks of power that influence their sense of job security; the local network based on their employing university and the national network of scholars who share the same field of research. The fights over what counts as research can and does drift from the intellectual to the political, and personal. Academic were able to identify specific instances of shunning and or punishment from their colleagues related directly to the dissemination of research that spoke against the grain of the local or national networks. Academics identified specific signals from both of these networks indicating that their career was flourishing or withering. Implications: This research examined insights from those who persevered when the fights over what and who counts drifted from the intellectual to the political, and the personal. Considerations of why such drifts happen were offered in the form of a socio-political construct called Fit, which included thoughts on hegemony, discourse, and identity. This effort reveals the importance of understanding what professional capital is relative to job security. It also reveals that fear is an enmeshed and often unspoken part of the culture of Academia. Further research to triangulate these findings would be helpful within international contexts.

Keywords: politics, academia, job security, context

Procedia PDF Downloads 317

Authors: Zbigniew Czyż, Adam Majczak, Lukasz Grabowski

Abstract:

The paper presents a description of geometric models, computational algorithms, and results of numerical analyses of charge exchange in a two-stroke opposed-piston engine. The research engine was a newly designed internal Diesel engine. The unit is characterized by three cylinders in which three pairs of opposed-pistons operate. The engine will generate a power output equal to 100 kW at a crankshaft rotation speed of 3800-4000 rpm. The numerical investigations were carried out using ANSYS FLUENT solver. Numerical research, in contrast to experimental research, allows us to validate project assumptions and avoid costly prototype preparation for experimental tests. This makes it possible to optimize the geometrical model in countless variants with no production costs. The geometrical model includes an intake manifold, a cylinder, and an outlet manifold. The study was conducted for a series of modifications of manifolds and intake and exhaust ports to optimize the charge exchange process in the engine. The calculations specified a swirl coefficient obtained under stationary conditions for a full opening of intake and exhaust ports as well as a CA value of 280° for all cylinders. In addition, mass flow rates were identified separately in all of the intake and exhaust ports to achieve the best possible uniformity of flow in the individual cylinders. For the models under consideration, velocity, pressure and streamline contours were generated in important cross sections. The developed models are designed primarily to minimize the flow drag through the intake and exhaust ports while the mass flow rate increases. Firstly, in order to calculate the swirl ratio [-], tangential velocity v [m/s] and then angular velocity ω [rad / s] with respect to the charge as the mean of each element were calculated. The paper contains comparative analyses of all the intake and exhaust manifolds of the designed engine. Acknowledgement: This work has been realized in the cooperation with The Construction Office of WSK "PZL-KALISZ" S.A." and is part of Grant Agreement No. POIR.01.02.00-00-0002/15 financed by the Polish National Centre for Research and Development.

Keywords: computational fluid dynamics, engine swirl, fluid mechanics, mass flow rates, numerical analysis, opposed-piston engine

Procedia PDF Downloads 193

Authors: Suaka Yaro

Abstract:

This article provides an alternative examination of the causes and the ramifications of the Ivorian political conflict from 2002 to 2009. The researcher employed a constructivist epistemology and qualitative study based upon fieldwork in different African cities interviewing Ivorians outside and within Ivory Coast. A purposive sampling of fourteen participants was selected. A purposive sampling was used to select fourteen respondents. The respondents were selected based on their involvement in Ivorian conflict. Their experiences on the causes and effects of the conflict were tapped for analysis. Qualitative methodology was used for the study. The data collection instruments were semi-structured interview questions, open-ended semi-structured questionnaire, and documentary analysis. The perceptions of these participants on the causes, effects and the possible solution to the endemic conflict in their homeland hold key perspectives that have hitherto been ignored in the whole debate about the Ivorian political conflict and its legacies. Finally, from the synthesized findings of the investigation, the researcher concluded that the analysed data revealed that the causes of the conflict were competition for scarce resources, bad governance, media incitement, xenophobia, incessant political power struggle and the proliferation of small firearms entering the country. The effects experienced during the conflict were the human rights violation, destruction of property including UN premises and displaced people both internally and externally. Some recommendations made include: Efforts should be made by the government to strengthen good relationship among different ethnic groups and help them adapt to new challenges that confront democratic developments in the country. The government should organise the South African style of Truth and Reconciliation Commission to revisit the horrors of the past in order to heal wounds and prevent future occurrence of the conflict. Employment opportunities and other income generating ventures for Ivorian should be created by the government by attracting local and foreign investors. The numerous rebels should be given special skills training in other for them to be able to live among the communities in Ivory Coast. Government of national unity should be encouraged in situation like this.

Keywords: displaced, federalism, pluralism, identity politics, grievance, eligibility, greed

Procedia PDF Downloads 218

Authors: Fadi Saleh, Çığdem Sezer Zhmurov

Abstract:

Biopharmaceuticals represent one of the wildest developing fields within biotechnology, and the biological macromolecules being produced inside cells have a variety of applications for therapies. In the past, mammalian cells, especially CHO cells, have been employed in the production of biopharmaceuticals. This is because these cells can achieve human-like completion of PTM. These systems, however, carry apparent disadvantages like high production costs, vulnerability to contamination, and limitations in scalability. This research is focused on the utilization of microalgae as a bioreactor system for the synthesis of biopharmaceutical glycoproteins in relation to PTMs, particularly N-glycosylation. The research points to a growing interest in microalgae as a potential substitute for more conventional expression systems. A number of advantages exist in the use of microalgae, including rapid growth rates, the lack of common human pathogens, controlled scalability in bioreactors, and the ability of some PTMs to take place. Thus, the potential of microalgae to produce recombinant proteins with favorable characteristics makes this a promising platform in order to produce biopharmaceuticals. The study focuses on the examination of the N-glycosylation pathways across different species of microalgae. This investigation is important as N-glycosylation—the process by which carbohydrate groups are linked to proteins—profoundly influences the stability, activity, and general performance of glycoproteins. Additionally, bioinformatics methodologies are employed to explain the genetic pathways implicated in N-glycosylation within microalgae, with the intention of modifying these organisms to produce glycoproteins suitable for human consumption. In this way, the present comparative analysis of the N-glycosylation pathway in humans and microalgae can be used to bridge both systems in order to produce biopharmaceuticals with humanized glycosylation profiles within the microalgal organisms. The results of the research underline microalgae's potential to help improve some of the limitations associated with traditional biopharmaceutical production systems. The study may help in the creation of a cost-effective and scale-up means of producing quality biopharmaceuticals by modifying microalgae genetically to produce glycoproteins with N-glycosylation that is compatible with humans. Improvements in effectiveness will benefit biopharmaceutical production and the biopharmaceutical sector with this novel, green, and efficient expression platform. This thesis, therefore, is thorough research into the viability of microalgae as an efficient platform for producing biopharmaceutical glycoproteins. Based on the in-depth bioinformatic analysis of microalgal N-glycosylation pathways, a platform for their engineering to produce human-compatible glycoproteins is set out in this work. The findings obtained in this research will have significant implications for the biopharmaceutical industry by opening up a new way of developing safer, more efficient, and economically more feasible biopharmaceutical manufacturing platforms.

Keywords: microalgae, glycoproteins, post-translational modification, genome

Procedia PDF Downloads 11

Authors: Stephan Schiffer, Andreas Kain, Philipp Wilde, Maximilian Helbing, Bernard Bäker

Abstract:

Automobile manufacturers progressively focus on a downsizing strategy to meet the EU's CO2 requirements concerning type-approval consumption cycles. The reduction in naturally aspirated engine power is compensated by increased levels of turbocharging. By downsizing conventional engines, CO2 emissions are reduced. However, it also implicates major challenges regarding longitudinal dynamic characteristics. An example of this circumstance is the delayed turbocharger-induced torque reaction which leads to a partially poor response behavior of the vehicle during acceleration operations. That is why it is important to focus conventional drive train design on real customer driving again. The currently considered dynamic maneuvers like the acceleration time 0-100 km/h discussed by journals and car manufacturers describe longitudinal dynamics experienced by a driver inadequately. For that reason we present the realization and evaluation of a comprehensive proband study. Subjects are provided with different vehicle concepts (electrified vehicles, vehicles with naturally aspired engines and vehicles with different concepts of turbochargers etc.) in order to find out which dynamic criteria are decisive for a subjectively strong acceleration and response behavior of a vehicle. Subsequently, realistic acceleration criteria are derived. By weighing the criteria an evaluation metric is developed to objectify customer-oriented transient dynamics. Fully-electrified vehicles are the benchmark in terms of customer-oriented longitudinal dynamics. The electric machine provides the desired torque almost without delay. This advantage compared to combustion engines is especially noticeable at low engine speeds. In conclusion, we will show the degree to which extent customer-relevant longitudinal dynamics of conventional vehicles can be approximated to electrified vehicle concepts. Therefore, various technical measures (turbocharger concepts, 48V electrical chargers etc.) and drive train designs (e.g. varying the final drive) are presented and evaluated in order to strengthen the vehicle’s customer-relevant transient dynamics. As a rating size the newly developed evaluation metric will be used.

Keywords: 48V, customer-oriented driving dynamics, electric charger, electrified vehicles, vehicle concepts

Procedia PDF Downloads 402

Authors: Kaushik Vaideeswaran, Jean Gobet, Patrick Margraf, Olha Sereda

Abstract:

Nitrocarburisation is a surface hardening technique often applied to improve the wear resistance of steel surfaces. It is considered to be a promising solution in comparison with other processes such as flame spraying, owing to the formation of a diffusion layer which provides mechanical integrity, as well as its cost-effectiveness. To improve other tribological properties of the surface such as the coefficient of friction (COF), dry lubricants are utilized. Currently, the lifetime of steel components in many applications using either of these techniques individually are faced with the limitations of the two: high COF for nitrocarburized surfaces and low wear resistance of dry lubricant coatings. To this end, the current study involves the creation of a hybrid surface using the impregnation of a dry lubricant on to a nitrocarburized surface. The mechanical strength and hardness of Gerster SA’s nitrocarburized surfaces accompanied by the impregnation of the porous outermost layer with a solid lubricant will create a hybrid surface possessing both outstanding wear resistance and a low friction coefficient and with high adherence to the substrate. Gerster SA has the state-of-the-art technology for the surface hardening of various steels. Through their expertise in the field, the nitrocarburizing process parameters (atmosphere, temperature, dwelling time) were optimized to obtain samples that have a distinct porous structure (in terms of size, shape, and density) as observed by metallographic and microscopic analyses. The porosity thus obtained is suitable for the impregnation of a dry lubricant. A commercially available dry lubricant with a thermoplastic matrix was employed for the impregnation process, which was optimized to obtain a void-free interface with the surface of the nitrocarburized layer (henceforth called hybrid surface). In parallel, metallic samples without nitrocarburisation were also impregnated with the same dry lubricant as a reference (henceforth called reference surface). The reference and the nitrocarburized surfaces, with and without the dry lubricant were tested for their tribological behavior by sliding against a quenched steel ball using a nanotribometer. Without any lubricant, the nitrocarburized surface showed a wear rate 5x lower than the reference metal. In the presence of a thin film of dry lubricant ( < 2 micrometers) and under the application of high loads (500 mN or ~800 MPa), while the COF for the reference surface increased from ~0.1 to > 0.3 within 120 m, the hybrid surface retained a COF < 0.2 for over 400m of sliding. In addition, while the steel ball sliding against the reference surface showed heavy wear, the corresponding ball sliding against the hybrid surface showed very limited wear. Observations of the sliding tracks in the hybrid surface using Electron Microscopy show the presence of the nitrocarburized nodules as well as the lubricant, whereas no traces of the lubricant were found in the sliding track on the reference surface. In this manner, the clear advantage of combining nitrocarburisation with the impregnation of a dry lubricant towards forming a hybrid surface has been demonstrated.

Keywords: dry lubrication, hybrid surfaces, improved wear resistance, nitrocarburisation, steels

Procedia PDF Downloads 118

Authors: Priyanka Gupta, Nilanjana Bairagi, Deepti Gupta

Abstract:

New pathogenic strains of microbes are continually emerging and resistance of bacteria to antibiotics is growing. Hospitals in India have a high burden of infections in their intensive care units and general wards. Rising incidence of hospital infections is a matter of great concern in India. This growth is often attributed to the absence of effective infection control strategies in healthcare facilities. Government, therefore, is looking for cost effective strategies that are effective against HAIs. One possible method is by application of an antimicrobial finish on the uniform. But there are limited studies to show the effect of antimicrobial activity of antimicrobial finish treated nurses’ uniforms in a real hospital set up. This paper proposes a prospective non-destructive sampling technique, based on the use of a detachable fabric patch, to assess the effectiveness of silver based antimicrobial agent across five wards in a tertiary care government hospital in Delhi, India. Fabrics like polyester and polyester cotton blend fabric which are more prevalent for making coats were selected for the study. Polyester and polyester cotton blend fabric was treated with silver based antimicrobial (AM) finish. At the beginning of shift, a composite patch of untreated and treated fabric respectively was stitched on the abdominal region on the left and right side of the washed white coat of participating nurse. At the end of the shift, the patch was removed and taken for bacterial sampling on Brain Heart Infusion (BHI) plates. Microbial contamination on polyester and blend fabrics after 6 hours shift was compared in Brain Heart Infusion broth (BHI). All patches treated with silver based antimicrobial agent showed decreased bacterial counts. Percent reduction in the bacterial colonies after the antimicrobial treatment in both fabrics was 81.0 %. Antimicrobial finish was equally effective in reducing microbial adhesion on both fabric types. White coats of nurses become progressively contaminated during clinical care. Type of fabric used to make the coat can affect the extent of contamination which is higher on polyester cotton blend as compared to 100% polyester. The study highlights the importance of silver based antimicrobial finish in the area of uniform hygiene. Bacterial load can be reduced by using antimicrobial finish on hospital uniforms. Hospital staff uniforms endowed with antimicrobial properties may be of great help in reducing the occurrence and spread of infections.

Keywords: antimicrobial finish, bacteria, infection control, silver, white coat

Procedia PDF Downloads 209

Authors: Naziema B. Jappie

Abstract:

Over the last 23 years leaders in government, political parties and universities have been spending much time on identifying and discussing various gaps in the system that impact systematically on students especially those from historically Black communities. Equity and access to higher education were two critical aspects that featured in achieving the transformation goals together with a funding model for those previously disadvantaged. Free education was not a feasible option for the government. Institutional leaders in higher education face many demands on their time and resources. Often, the time for crisis management planning or consideration of being proactive and preventative is not a standing agenda item. With many issues being priority in academia, people become complacent and think that crisis may not affect them or they will cross the bridge when they get to it. Historically South Africa has proven to be a country of militancy, strikes and protests in most industries, some leading to disastrous outcomes. Higher education was not different between October 2015 and late 2016 when the #Rhodes Must Fall which morphed into the # Fees Must Fall protest challenged the establishment, changed the social fabric of universities, bringing the sector to a standstill. Some institutional leaders and administrators were better at handling unexpected, high-consequence situations than others. At most crisis leadership is viewed as a situation more than a style of leadership which is usually characterized by crisis management. The objective of this paper is to show how institutions managed catastrophes of disastrous proportions, down through unexpected incidents of 2015/2016. The content draws on the vast past crisis management experience of the presenter and includes the occurrences of the recent protests giving an event timeline. Using responses from interviews with institutional leaders and administrators as well as students will ensure first-hand information on their experiences and the outcomes. Students have tasted the power of organized action and they demand immediate change, if not the revolt will continue. This paper will examine the approaches that guided institutional leaders and their crisis teams and sector crisis response. It will further expand on whether the solutions effectively changed governance in higher education or has it minimized the need for more protests. The conclusion will give an insight into the future of higher education in South Africa from a leadership perspective.

Keywords: crisis, governance, intervention, leadership, strategies, protests

Procedia PDF Downloads 141

Authors: Swati Rajput

Abstract:

Environmental psychology explains that the person is a social agent that seeks to extract meaning from their built and natural environment to behave in a particular manner. It also shows the attachment or detachment of people to their environment. Assessing environmental psychology of people is imperative for planners and policy makers for urban planning. The paper investigates the environmental psychology of people living in nine districts of Delhi by calculating and assessing their Environmental Emotional Quotient (EEQ). Emotional Quotient deals with the ability to sense, understand, attach and respond according to the power of emotions. An Environmental Emotional Quotient has been formulated based upon the inventory administered to them. The respondents were asked questions related to their view and emotions about the green spaces, water resource conservation, air and environmental quality. An effort has been made to assess the feeling of belongingness among the residents. Their views were assessed on green spaces, reuse, and recycling of resources and their participation level. They were also been assessed upon health awareness level by considering both preventive and curative segments of health care. It was found that only 12 percent of the people is emotionally attached to their surroundings in the city. The emotional attachment reduces as we move away from the house to housing complex to neighbouring areas and rest of the city. In fact, the emotional quotient goes lower to lowest from house to other ends of the city. It falls abruptly after the radius of 1 km from the residence. The result also shows that nearly 54% respondents accept that there is environment pollution in their area. Around 47.8% respondents in the survey consider that diseases occur because of green cover depiction in their area. Major diseases are to airborne diseases like asthma and bronchitis. Seasonal disease prevalent, which specially occurred from last 3-4 years are malaria, dengue and chikengunya. Survey also shows that only 31 % of respondents visit government hospitals while 69% respondents visit private hospitals or small clinics for healthcare services. The paper suggests the need for environmental sensitive policies and need for green insurance in mega cities like Delhi.

Keywords: environmental psychology, environmental emotional quotient, preventive health care and curative health care, sustainable living

Procedia PDF Downloads 271

Authors: Ishara Madusanka, So Morikawa

Abstract:

Natural disasters, particularly floods, pose severe challenges globally, affecting both developed and developing countries. In many regions, especially Asia, riverine floods are prevalent and devastating. Integrated flood management incorporates structural and non-structural measures, with preventive relocation emerging as a cost-effective and proactive strategy for areas repeatedly impacted by severe flooding. However, preventive relocation is often hindered by economic, psychological, social, and institutional barriers. This study investigates the factors influencing resistance to preventive relocation and evaluates the role of flood risk information in shaping relocation decisions through risk perception. A conceptual model was developed, incorporating variables such as Flood Risk Information (FRI), Place Attachment (PA), Good Living Conditions (GLC), and Adaptation to Flooding (ATF), with Flood Risk Perception (FRP) serving as a mediating variable. The research was conducted in Welipitiya in the Polwatta river basin, Matara district, Sri Lanka, a region experiencing recurrent flood damage. For this study, an experimental design involving a structured questionnaire survey was utilized, with 185 households participating. The treatment group received flood risk information, including flood risk maps and historical data, while the control group did not. Data were collected in 2023 and analyzed using independent sample t-tests and Partial Least Squares Structural Equation Modeling (PLS-SEM). PLS-SEM was chosen for its ability to model latent variables, handle complex relationships, and suitability for exploratory research. Multi-group Analysis (MGA) assessed variations across different flood risk areas. Findings indicate that flood risk information had a limited impact on flood risk perception and relocation decisions, though its effect was significant in specific high-risk areas. Place attachment was a significant factor influencing relocation decisions across the sample. One potential reason for the limited impact of flood risk information on relocation decisions could be the lack of specificity in the information provided. The results suggest that while flood risk information alone may not significantly influence relocation decisions, it is crucial in specific contexts. Future studies and practitioners should focus on providing more detailed risk information and addressing psychological factors like place attachments to enhance preventive relocation efforts.

Keywords: flood risk communication, flood risk perception, place attachment, preventive relocation, structural equation modeling

Procedia PDF Downloads 17

Authors: Anne C. Richer-De-Forges, Dominique Arrouays, Songchao Chen, Mercedes Roman Dobarco

Abstract:

Most of the digital soil mapping (DSM) products rely on machine learning (ML) prediction models and/or the use or pedotransfer functions (PTF) in which calibration data come from soil analyses performed in labs. However, many other observations (often qualitative, nominal, or ordinal) could be used as proxies of lab measurements or as input data for ML of PTF predictions. DSM and ML are briefly described with some examples taken from the literature. Then, we explore the potential of an ordinal qualitative variable, i.e., the hand-feel soil texture (HFST) estimating the mineral particle distribution (PSD): % of clay (0-2µm), silt (2-50µm) and sand (50-2000µm) in 15 classes. The PSD can also be measured by lab measurements (LAST) to determine the exact proportion of these particle-sizes. However, due to cost constraints, HFST are much more numerous and spatially dense than LAST. Soil texture (ST) is a very important soil parameter to map as it is controlling many of the soil properties and functions. Therefore, comes an essential question: is it possible to use HFST as a proxy of LAST for calibration and/or validation of DSM predictions of ST? To answer this question, the first step is to compare HFST with LAST on a representative set where both information are available. This comparison was made on ca 17,400 samples representative of a French region (34,000 km2). The accuracy of HFST was assessed, and each HFST class was characterized by a probability distribution function (PDF) of its LAST values. This enables to randomly replace HFST observations by LAST values while respecting the PDF previously calculated and results in a very large increase of observations available for the calibration or validation of PTF and ML predictions. Some preliminary results are shown. First, the comparison between HFST classes and LAST analyses showed that accuracies could be considered very good when compared to other studies. The causes of some inconsistencies were explored and most of them were well explained by other soil characteristics. Then we show some examples applying these relationships and the increase of data to several issues related to DSM. The first issue is: do the PDF functions that were established enable to use HSFT class observations to improve the LAST soil texture prediction? For this objective, we replaced all HFST for topsoil by values from the PDF 100 time replicates). Results were promising for the PTF we tested (a PTF predicting soil water holding capacity). For the question related to the ML prediction of LAST soil texture on the region, we did the same kind of replacement, but we implemented a 10-fold cross-validation using points where we had LAST values. We obtained only preliminary results but they were rather promising. Then we show another example illustrating the potential of using HFST as validation data. As in numerous countries, the HFST observations are very numerous; these promising results pave the way to an important improvement of DSM products in all the countries of the world.

Keywords: digital soil mapping, improvement of digital soil mapping predictions, potential of using hand-feel soil texture, soil texture prediction

Procedia PDF Downloads 215

Authors: Patrizia Palumbo

Abstract:

There are only two Italian films dealing with the Italian emigration to Germany: I magliari directed by Francesco Rosi and Itaker. Vietato agli italiani directed by Toni Trupia. Consequently, the analysis of these two films is essential to any study of the representation of the Italians’ experience in Germany, their hosting country. Francesco Rosi’s I magliari and Toni Trupia’s Itaker. Vietato agli italiani, released respectively in 1959 and in 2012, are both set in the second half of the twentieth century and deal with door to door Italian cloth sellers in German cities, con artists marketing rags as fine fabric to exclusively German customers. However, the perspective of the directors and screenwriters are, if not antithetical, profoundly different. Indeed, from 1959 to 2012, years in which the two films were released, Italy went from being a country of emigration to a country of both immigration (albeit now temporary) and emigration. The paper entitled ‘Representation of the Italian Emigration to Germany in the Films of Francesco Rosi and Toni Trupia’ will analyze, therefore, the two substantially different historical contingencies in which the two movies were produced and cast light on how the same historical reality, that of Italian cloth sellers in German cities, is portrayed by Rosi and Trupia’s films. In particular, it will show how in both films the female character is the site on which power (or the lack of it) is contested. More precisely, it will highlight how the German blond woman in Rosi’s film and the dark haired Albanian woman in Trupia’s film are a reflection of the changes Italy underwent in the last fifty years. Finally, this paper will comment on why Italian emigration to Germany has been overlooked by Italian scholars. Although these scholars are all familiar with many of the films directed by Francesco Rosi, one of the auteurs of Italian cinema, no real critical study of I magliari exists. Rosi’s film, it can be argued, may have aroused the uneasiness engendered by all works dealing with facts evoking shameful and humiliating times. The same is true for Trupia’s film. Even though his Itaker. Vietato agli italiani is set in the sixties, it cannot prescind from the reality of contemporary Italian emigration to Germany and Italy’s economic and political crisis. Bringing attention to Rosi and Trupia’s film seems to be a valid way to rekindle the interest in Italian emigration to Germany, a phenomenon that has contributed to the economic, social and cultural history of both Italy and Germany.

Keywords: film, Germany, history, Italian emigration

Procedia PDF Downloads 332

Authors: D. Hilton

Abstract:

The importance and significance of this research is based upon the fundamental knowledge reported in the scientific literature that physical activity is inversely associated with obesity. In addition, it is recognized there is a global epidemic of sedentariness while at the same time it is known that morbidity and mortality are associated with physical inactivity and as a result of overweight or obesity. Hence this small study in school students is an important area of research in our community. An application submitted in 2005 for the inaugural Public Health Education Research Trust [PHERT] Post Graduate Research Scholarship scheme organized by the Public Health Association of Australia [PHAA] was awarded 3rd place within Australia. The author and title was: D. Hilton, Methods to increase physical activity in school aged children [literature review, a trial using pedometers and a policy paper]. Third place is a good result, however this did not secure funding for the project, as only first place received $5000 funding. Some years later within Australia, a program commenced called the Global Children's Challenge [GCC]. Given details of the 2005 award above were included an application submission prepared for Parkhill Primary School [PPS] which is located in Victoria, Australia was successful. As a result, an excited combined grade 3/ 4 class at the school [27 students] in 2012 became recipients of these free pedometers. Ambassadors for the program were Mrs Catherine Freeman [OAM], Olympic Gold Medalist – Sydney 2000 [400 meters], while another ambassador was Mr Colin Jackson [CBE] who is a Welsh former sprint and hurdling athlete. In terms of PPS and other schools involved in 2012, website details show that the event started on 19th Sep 2012 and students were to wear the pedometer every day for 50 days [at home and at school] aiming for the recommended 15,000 steps/day recording steps taken in a booklet provided. After the finish, an analysis of the average step count for this school showed that the average steps taken / day was 14, 003 [however only a small percentage of students returned the booklets and units] as unfortunately the dates for the program coincided with school holidays so some students either forgot or misplaced the units / booklets. Unfortunately funding for this program ceased in 2013, however the lasting impact of the trial on student’s knowledge and awareness remains and in fact becomes a good grounding for students in how to monitor basic daily physical activity using a method that is easy, fun, low cost and readily accessible.

Keywords: walking, physical activity, exercise, Australian school

Procedia PDF Downloads 301

Authors: Sheyla Moroni

Abstract:

A number of scholars around the world have analyzed the great architectural and urban planning revolution proposed by Skopje 2014, but so far, there are no readings of the parallels between the museums in the Balkan area (including Greece) that share the same name as the museum at the center of that political and cultural revolution. In the former FYROM (now renamed North Macedonia), a museum called "Macedonian Struggle" was born during the reconstruction of the city of Skopje as the new "national" capital. This new museum was built under the "Skopje 2014" plan and cost about 560 million euros (1/3 of the country's GDP). It has been a "flagship" of the government of Nikola Gruevski, leader of the nationalist VMRO-DPMNE party. Until 2016 this museum was close to the motivations of the Macedonian nationalist movement (and later party) active (including terrorist actions) during the 19th and 20th centuries. The museum served to narrate a new "nation-building" after "state-building" had already taken place. But there are three other museums that tell the story of the "Macedonian struggle" by understanding "Macedonia" as a territory other than present-day North Macedonia. The first one is located in Thessaloniki and primarily commemorates the "Greek battle" against the Ottoman Empire. While the first uses a new dark building and many reconstructed rooms and shows the bloody history of the quest for "freedom" for the Macedonian language and people (different from Greeks, Albanians, and Bulgarians), the second is located in an old building in Thessaloniki and in its six rooms on the ground floor graphically illustrates the modern and contemporary history of Greek Macedonia. There are also third and fourth museums: in Kastoria (toward the Albanian border) and in Chromio (near the Greek-North Macedonian border). These two museums (Kastoria and Chromio) are smaller, but they mark two important borders for the (Greek) regions bordering Albania to the east and dividing it to the northwest not only from the Ottoman past but also from two communities felt to be "foreign" (Albanians and former Yugoslav Macedonians). All museums reconstruct a different "national edifice" and emphasize the themes of language and religion. The objective of the research is to understand, through four museums bearing the same name, what are the main "mental boundaries" (religious, linguistic, cultural) of the different states (reconstructed between the late 19th century and 1991). Both classical historiographic methodology (very different between Balkan and "Western" areas) and on-site observation and interactions with different sites are used in this research. An attempt is made to highlight four different political focuses with respect to nation-building and the Public History (and/or propaganda) approaches applied in the construction of these buildings and memorials tendency often that one "defines" oneself by differences from "others" (even if close).

Keywords: nationalisms, museum, nation building, public history

Procedia PDF Downloads 77