Search results for: advanced traffic management systems

Authors: Mishadi Herath, Amin Talei, Andreas Hermawan, Clarina Chua

Abstract:

Green walls are vegetated structures on building’s wall that are considered as part of sustainable urban design. They are proved to have many micro-climate benefits such as reduction in indoor temperature, noise attenuation, and improvement in air quality. On the other hand, several studies have also been conducted on potential reuse of greywater in urban water management. Greywater is relatively clean when compared to blackwater; therefore, this study was aimed to assess the potential reuse of it for irrigating a green wall system. In this study, the campus of Monash University Malaysia located in Selangor state was considered as the study site where total 48 samples of greywater were collected from 7 toilets hand-wash and 5 pantries during 3 months period. The samples were tested to characterize the quality of greywater in the study site and compare it with local standard for irrigation water. PH and concentration of heavy metals, nutrients, Total Suspended Solids (TSS), Biochemical Oxygen Demand (BOD), Chemical Oxygen Demand (COD), total Coliform and E.coli were measured. Results showed that greywater could be directly used for irrigation with minimal treatment. Since the effluent of the system was supposed to be drained to stormwater drainage system, the effluent needed to meet certain quality requirement. Therefore, a biofiltration system was proposed to host the green wall plants and also treat the greywater (which is used as irrigation water) to the required level. To assess the performance of the proposed system, an experimental setup consisting of Polyvinyl Chloride (PVC) soil columns with sand-based filter media were prepared. Two different local creeper plants were chosen considering several factors including fast growth, low maintenance requirement, and aesthetic aspects. Three replicates of each plants were used to ensure the validity of the findings. The growth of creeping plants and their survivability was monitored for 6 months while monthly sampling and testing of effluent was conducted to evaluate effluent quality. An analysis was also conducted to estimate the potential cost and benefit of such system considering water and energy saving in the system. Results showed that the proposed system can work efficiently throughout a long period of time with minimal maintenance requirement. Moreover, the biofiltration-green wall system was found to be successful in reusing greywater as irrigating water while the effluent was meeting all the requirements for being drained to stormwater drainage system.

Keywords: biofiltration, green wall, greywater, sustainability

Procedia PDF Downloads 200

Authors: Tamara Romero, Manuel Romero-Huelva, Jose V. Segarra, Jose Castro, Carlos Fernandez

Abstract:

Many foods resulting from processing and manufacturing end up as waste, most of which is burned, dumped into landfills or used as compost, which leads to wasted resources, and environmental problems due to unsuitable disposal. Using residues of the crop and food processing industries to feed livestock has the advantage to obviating the need for costly waste management programs. The main residue generated in citrus cultivations and rice crop are pruning waste and rice straw, respectively. Within Spain, the Valencian Community is one of the world's oldest citrus and rice production areas. The objective of this experiment found out the effects of including orange leaves and rice straw as ingredients in the concentrate diets of goats, on milk production and methane (CH₄) emissions. Ten Murciano-Granadina dairy goats (45 kg of body weight, on average) in mid-lactation were selected in a crossover design experiment, where each goat received two treatments in 2 periods. Both groups were fed with 1.7 kg pelleted mixed ration; one group (n= 5) was a control (C) and the other group (n= 5) used orange leaves and rice straw (OR). The forage was alfalfa hay, and it was the same for the two groups (1 kg of alfalfa was offered by goat and day). The diets employed to achieve the requirements during lactation period for caprine livestock. The goats were allocated to individual metabolism cages. After 14 days of adaptation, feed intake and milk yield were recorded daily over a 5 days period. Physico-chemical parameters and somatic cell count in milk samples were determined. Then, gas exchange measurements were recorded individually by an open-circuit indirect calorimetry system using a head box. The data were analyzed by mixed model with diet and digestibility as fixed effect and goat as random effect. No differences were found for dry matter intake (2.23 kg/d, on average). Higher milk yield was found for C diet than OR (2.3 vs. 2.1 kg/goat and day, respectively) and, greater milk fat content was observed for OR than C (6.5 vs. 5.5%, respectively). The cheese extract was also greater in OR than C (10.7 vs. 9.6%). Goats fed OR diet produced significantly fewer CH₄ emissions than C diet (27 vs. 30 g/d, respectively). These preliminary results (LIFE Project LOWCARBON FEED LIFE/CCM/ES/000088) suggested that the use of these waste by-products was effective in reducing CH₄ emission without detrimental effect on milk yield.

Keywords: agricultural waste, goat, milk production, methane emission

Procedia PDF Downloads 129

Authors: Chandragouda R. Patil, K. S. Jagadeesh, S. D. Kalolgi

Abstract:

Biofertilizers containing live microbial cells can mobilize one or more nutrients to plants when applied to either seed or rhizosphere. They form an integral part of nutrient management strategies for sustainable production of agricultural crops. Annually, about 22 tons of lignite-based biofertilizers are being produced and supplied to farmers at the Institute of Organic Farming, University of Agricultural Sciences, Dharwad, Karnataka state India. Although carrier based biofertilizers are common, they have shorter shelf life, poor quality, high contamination, unpredictable field performance and high cost of solid carriers. Hence, liquid formulations are being developed to increase their efficacy and broaden field applicability. An attempt was made to develop liquid formulation of strains of Rhizobium NC-92 (Groundnut), Azospirillum ACD15 both nitrogen-fixing biofertilizers and Pseudomonas striata an efficient P-solubilizing bacteria (PSB). Different concentration of amendments such as additives (glycerol and polyethylene glycol), adjuvants (carboxyl methyl cellulose), gum arabica (GA), surfactant (polysorbate) and trehalose specifically for Azospirillum were found essential. Combinations of formulations of Rhizobium and PSB for groundnut and Azospirillum and PSB for maize were evaluated under field conditions to determine the optimum level of inoculum required. Each biofertilizer strain was inoculated at the rate of 2, 4, 8 ml per kg of seeds and the efficacy of each formulation both individually and in combinations was evaluated against the lignite-based formulation at the rate of 20 g each per kg seeds and a un-inoculated set was included to compare the inoculation effect. The field experiment had 17 treatments in three replicates and the best level of inoculum was decided based on net returns and cost: benefit ratio. In peanut, the combination of 4 ml of Rhizobium and 2 ml of PSB resulted in the highest net returns and higher cost to benefit ratio of 1:2.98 followed by treatment with a combination of 2 ml per kg each of Rhizobium and PSB with a B;C ratio of 1:2.84. The benefits in terms of net returns were to the extent of 16 percent due to inoculation with lignite based formulations while it was up to 48 percent due to the best combination of liquid biofertilizers. In maize combination of liquid formulations consisting of 4 ml of Azospirillum and 2 ml of PSB resulted in the highest net returns; about 53 percent higher than the un-inoculated control and 20 percent higher than the treatment with lignite based formulation. In both the crops inoculation with lignite based formulations significantly increased the net returns over un-inoculated control while levels higher or lesser than 4 ml of Rhizobium and Azospirillum and higher or lesser than 2 ml of PSB were not economical and hence not optimal for these two crops.

Keywords: Rhizobium, Azospirillum, phosphate solubilizing bacteria, liquid formulation, benefit-cost ratio

Procedia PDF Downloads 476

Authors: Ashima Sharma

Abstract:

Human Serum Albumin (HSA)- one of the most demanded therapeutic proteins with immense biotechnological applications- is a large multidomain protein containing 17 disulfide bonds. The current source of HSA is human blood plasma which is a limited and unsafe source. Thus, there exists an indispensable need to promote non-animal derived recombinant HSA (rHSA) production. Escherichia coli is one of the most convenient hosts which had contributed to the production of more than 30% of the FDA approved recombinant pharmaceuticals. It grows rapidly and reaches high cell density using inexpensive and simple substrates. E. coli derived recombinant products have more economic potential as fermentation processes are cheaper compared to the other expression hosts. The major bottleneck in exploiting E. coli as a host for a disulfide-rich multidomain protein is the formation of aggregates of overexpressed protein. The majority of the expressed HSA forms inclusion bodies (more than 90% of the total expressed rHSA) in the E. coli cytosol. Recovery of functional rHSA from inclusion bodies is not preferred because it is difficult to obtain a large multidomain disulfide bond rich protein like rHSA in its functional native form. Purification is tedious, time-consuming, laborious and expensive. Because of such limitations, the E. coli host system was neglected for rHSA production for the past few decades despite its numerous advantages. In the present work, we have exploited the capabilities of E. coli as a host for the enhanced functional production of rHSA (~60% of the total expressed rHSA in the soluble fraction). Parameters like intracellular environment, temperature, induction type, duration of induction, cell lysis conditions etc. which play an important role in enhancing the level of production of the desired protein in its native form in vivo have been optimized. We have studied the effect of assistance of different types of exogenously employed chaperone systems on the functional expression of rHSA in the E. coli host system. Different aspects of cell growth parameters during the production of rHSA in presence and absence of molecular chaperones in E. coli have also been studied. Upon overcoming the difficulties to produce functional rHSA in E. coli, it has been possible to produce significant levels of functional protein through engineering the biological system of protein folding in the cell, the E. coli-derived rHSA has been purified to homogeneity. Its detailed physicochemical characterization has been performed by monitoring its conformational properties, secondary and tertiary structure elements, surface properties, ligand binding properties, stability issues etc. These parameters of the recombinant protein have been compared with the naturally occurring protein from the human source. The outcome of the comparison reveals that the recombinant protein resembles exactly the same as the natural one. Hence, we propose that the E. coli-derived rHSA is an ideal biosimilar for human blood plasma-derived serum albumin. Therefore, in the present study, we have introduced and promoted the E. coli- derived rHSA as an alternative to the preparation from a human source, pHSA.

Keywords: recombinant human serum albumin, Escherichia coli, biosimilar, chaperone assisted protein folding

Procedia PDF Downloads 195

Authors: Filipa Lancastre, Carmen Lages, Filipe Santos

Abstract:

The concept of social entrepreneurship (SE) remains ambiguous and deprived of a widely accepted operational definition. We argue that an awareness about the consensual constituent elements of SE from all key players from its ecosystem as well as a deeper understanding of apparently divergent perspectives will allow the different stakeholders (social entrepreneurs, corporations, investors, policymakers, the beneficiaries themselves) to bridge and cooperate for societal value co-creation in trying to solve our most pressing societal issues. To address our research question –what are the dimensions of SE that are consensual and controversial across existing perspectives? – We designed a two-step qualitative study. In a first step, we conducted an extensive literature review, collecting and analyzing 155 different SE definitions. From this initial step, we extracted and characterized three consensual and six controversial dimensions of the SE concept. In a second step, we conducted 20 semi-structured interviews with practitioners that are actively involved in the SE field. The goal of this second step was to verify if the literature did not capture any key dimension, understand how the dimensions related to each other and to understand the rationale behind them. The dimensions of the SE concept were extracted based on the relevance of each theme and on the theoretical relationship among them. To identify the relevance, we used as a proxy the frequency of each theme was referred to in our sample of definitions. To understand relationships, as identified in the previous section, we included concepts from both the management and psychology literature, such as the Entrepreneurial Orientation concept from the entrepreneurship literature, the Subjective Well Being construct from psychology literature, and the Resource-Based Theory from the strategy literature. This study has two main contributions; First, the identification of (consensual and controversial) dimensions of SE that exist across scattered definitions from the academic and practitioner literature. Second, a framework that parsimoniously synthesizes four dominant perspectives of SE and relates them with the SE dimensions. Assuming the contested nature of the SE concept, it is not expected that these views will be reconciled at the academic or practitioner field level. In future research, academics can, however, be aware of the existence of different understandings of SE and avoid bias towards a single view, developing holistic studies on SE phenomena or comparing differences by studying their underlying assumptions. Additionally, it is important that researchers make explicit the perspective they are embracing to ensure consistency among the research question, sampling procedures and implications of results. At the practitioner level, individuals or groups following different logics are predictably mutually suspicious and might benefit from taking stock of other perspectives on SE, building bridges and fostering cross-fertilization to the benefit of the SE ecosystem for which all contribute.

Keywords: social entrepreneurship, conceptualization, dimensions, perspectives

Procedia PDF Downloads 157

Authors: Minna Pikkarainen, Yueqiang Xu

Abstract:

The integration of digital technology with existing healthcare processes has been painfully slow, a huge gap exists between the fields of strictly regulated official medical care and the quickly moving field of health and wellness technology. We claim that the promises of preventive healthcare can only be fulfilled when this gap is closed – health care and self-care becomes seamless continuum “correct information, in the correct hands, at the correct time allowing individuals and professionals to make better decisions” what we call connected health approach. Currently, the issues related to security, privacy, consumer consent and data sharing are hindering the implementation of this new paradigm of healthcare. This could be solved by following MyData principles stating that: Individuals should have the right and practical means to manage their data and privacy. MyData infrastructure enables decentralized management of personal data, improves interoperability, makes it easier for companies to comply with tightening data protection regulations, and allows individuals to change service providers without proprietary data lock-ins. This paper tackles today’s unprecedented challenges of enabling and stimulating multiple healthcare data providers and stakeholders to have more active participation in the digital health ecosystem. First, the paper systematically proposes the MyData approach for healthcare and preventive health data ecosystem. In this research, the work is targeted for health and wellness ecosystems. Each ecosystem consists of key actors, such as 1) individual (citizen or professional controlling/using the services) i.e. data subject, 2) services providing personal data (e.g. startups providing data collection apps or data collection devices), 3) health and wellness services utilizing aforementioned data and 4) services authorizing the access to this data under individual’s provided explicit consent. Second, the research extends the existing four archetypes of orchestrator-driven healthcare data business models for the healthcare industry and proposes the fifth type of healthcare data model, the MyData Blockchain Platform. This new architecture is developed by the Action Design Research approach, which is a prominent research methodology in the information system domain. The key novelty of the paper is to expand the health data value chain architecture and design from centralization and pseudo-decentralization to full decentralization, enabled by blockchain, thus the MyData blockchain platform. The study not only broadens the healthcare informatics literature but also contributes to the theoretical development of digital healthcare and blockchain research domains with a systemic approach.

Keywords: blockchain, health data, platform, action design

Procedia PDF Downloads 84

Authors: Bahar Salavati Vie Le Sage, Ismaïl Ben Hariz, Flavien Viguier, Sirine Noura Kahil, Audrey Jacquin, Maxime Convert

Abstract:

The ballast layer plays a key role in railroad maintenance and the geometry of the track structure. Ballast also holds the track in place as the trains roll over it. Track ballast is packed between the sleepers and on the sides of railway tracks. An imbalance in ballast volume on the tracks can lead to safety issues as well as a quick degradation of the overall quality of the railway segment. If there is a lack of ballast in the track bed during the summer, there is a risk that the rails will expand and buckle slightly due to the high temperatures. Furthermore, the knowledge of the ballast quantities that will be excavated during renewal works is important for efficient ballast management. The volume of excavated ballast per meter of track can be calculated based on excavation depth, excavation width, volume of track skeleton (sleeper and rail) and sleeper spacing. Since 2012, SNCF has been collecting 3D points cloud data covering its entire railway network by using 3D laser scanning technology (LiDAR). This vast amount of data represents a modelization of the entire railway infrastructure, allowing to conduct various simulations for maintenance purposes. This paper aims to present an automated method for ballast volume estimation based on the processing of LiDAR data. The estimation of abnormal volumes in ballast on the tracks is performed by analyzing the cross-section of the track. Further, since the amount of ballast required varies depending on the track configuration, the knowledge of the ballast profile is required. Prior to track rehabilitation, excess ballast is often present in the ballast shoulders. Based on 3D laser scans, a Digital Terrain Model (DTM) was generated and automatic extraction of the ballast profiles from this data is carried out. The surplus in ballast is then estimated by performing a comparison between this ballast profile obtained empirically, and a geometric modelization of the theoretical ballast profile thresholds as dictated by maintenance standards. Ideally, this excess should be removed prior to renewal works and recycled to optimize the output of the ballast renewal machine. Based on these parameters, an application has been developed to allow the automatic measurement of ballast profiles. We evaluated the method on a 108 kilometers segment of railroad LiDAR scans, and the results show that the proposed algorithm detects ballast surplus that amounts to values close to the total quantities of spoil ballast excavated.

Keywords: ballast, railroad, LiDAR , cloud point, track ballast, 3D point

Procedia PDF Downloads 89

Authors: Mangala. Sadasivan, Mary Hughes, Bryan Kelly

Abstract:

Medical Education must focus on bridging the gap between teaching and learning when training pre-clinical year students in skills needed to keep up with medical knowledge and to meet the demands of health care in the future. The authors were interested in showing that a 3-S Model (building strength, developing stamina, and increasing speed) using a bridged curriculum design helps connect teaching and learning and improves students’ retention of basic science and clinical knowledge. The authors designed three learning modules using the 3-S Model within a systems course in a pre-clerkship medical curriculum. Each module focused on a bridge (concept map) designed by the instructor for specific content delivered to students in the course. This with-in-subjects design study included 304 registered MSU osteopathic medical students (3 campuses) ranked by quintile based on previous coursework. The instructors used the bridge to create self-directed learning exercises (building strength) to help students master basic science content. Students were video coached on how to complete assignments, and given pre-tests and post-tests designed to give them control to assess and identify gaps in learning and strengthen connections. The instructor who designed the modules also used video lectures to help students master clinical concepts and link them (building stamina) to previously learned material connected to the bridge. Boardstyle practice questions relevant to the modules were used to help students improve access (increasing speed) to stored content. Unit Examinations covering the content within modules and materials covered by other instructors teaching within the units served as outcome measures in this study. This data was then compared to each student’s performance on a final comprehensive exam and their COMLEX medical board examinations taken some time after the course. The authors used mean comparisons to evaluate students’ performances on module items (using 3-S Model) to non-module items on unit exams, final course exam and COMLEX medical board examination. The data shows that on average, students performed significantly better on module items compared to non-module items on exams 1 and 2. The module 3 exam was canceled due to a university shut down. The difference in mean scores (module verses non-module) items disappeared on the final comprehensive exam which was rescheduled once the university resumed session. Based on Quintile designation, the mean scores were higher for module items than non-module items and the difference in scores between items for Quintiles 1 and 2 were significantly better on exam 1 and the gap widened for all Quintile groups on exam 2 and disappeared in exam 3. Based on COMLEX performance, all students on average as a group, whether they Passed or Failed, performed better on Module items than non-module items in all three exams. The gap between scores of module items for students who passed COMLEX to those who failed was greater on Exam 1 (14.3) than on Exam 2 (7.5) and Exam 3 (10.2). Data shows the 3-S Model using a bridge effectively connects teaching and learning

Keywords: bridging gap, medical education, teaching and learning, model of learning

Procedia PDF Downloads 43

Authors: Yohana Fessehazion

Abstract:

Mercury is a prominent example of a heavy metal contaminant in the environment, and it has been extensively investigated for its potential health risk in humans and other organisms. In South Africa, massive mercury contamination happened in1980s when the England-based mercury reclamation processing plant relocated to Cato Ridge, KwaZulu-Natal Province, and discharged mercury waste into the Mngceweni River. This mercury waste discharge resulted in high mercury concentration that exceeded the acceptable levels in Mngceweni River, Umgeni River, and human hair of the nearby villagers. This environmental issue raised the alarm, and over the years, several environmental assessments were reported the dire environmental crises resulting from the Thor Chemicals (now known as Metallica Chemicals) and urged the immediate removal of the around 3,000 tons of mercury waste stored in the factory storage facility over two decades. Recently theft of some containers with the toxic substance from the Thor Chemicals warehouse and the subsequent fire that ravaged the facility furtherly put the factory on the spot escalating the urgency of left behind deadly mercury waste removal. This project aims to investigate the mercury contamination leaking from an old Thor Chemicals mercury processing plant. The focus will be on sediments, water, terrestrial plants, and aquatic weeds such as the prominent water hyacinth weeds in the nearby water systems of Mngceweni River, Umgeni River, and Inanda Dam as a bio-indicator and phytoremediator for mercury pollution. Samples will be collected in spring around October when the condition is favourable for microbial activity to methylate mercury incorporated in sediments and blooming season for some aquatic weeds, particularly water hyacinth. Samples of soil, sediment, water, terrestrial plant, and aquatic weed will be collected per sample site from the point of source (Thor Chemicals), Mngceweni River, Umgeni River, and the Inanda Dam. One-way analysis of variance (ANOVA) tests will be conducted to determine any significant differences in the Hg concentration among all sampling sites, followed by Least Significant Difference post hoc test to determine if mercury contamination varies with the gradient distance from the source point of pollution. The flow injection atomic spectrometry (FIAS) analysis will also be used to compare the mercury sequestration between the different plant tissues (roots and stems). The principal component analysis is also envisaged for use to determine the relationship between the source of mercury pollution and any of the sampling points (Umgeni and Mngceweni Rivers and the Inanda Dam). All the Hg values will be expressed in µg/L or µg/g in order to compare the result with the previous studies and regulatory standards. Sediments are expected to have relatively higher levels of Hg compared to the soils, and aquatic macrophytes, water hyacinth weeds are expected to accumulate a higher concentration of mercury than terrestrial plants and crops.

Keywords: mercury, phytoremediation, Thor chemicals, water hyacinth

Procedia PDF Downloads 199

Authors: Jessica Arthur, Duke Amegah, Kingsley Akenten Wiafe

Abstract:

Background: Vanilla planifolia is the only edible fruit of the orchid family (Orchidaceae) among the over 35,000 Orchidaceae species found worldwide. In Ghana, Vanilla was discovered in the wild, but it is underutilized for commercial production, most likely due to a lack of knowledge on the best NAA and BAP combinations for in vitro propagation to promote successfully regenerated plant acclimatization. The growing interest and global demand for elite Vanilla planifolia plants and natural vanilla flavour emphasize the need for an effective industrial-scale micropropagation protocol. Tissue culture systems are increasingly used to grow disease-free plants and reliable in vitro methods can also produce plantlets with typically modest proliferation rates. This study sought to develop an efficient protocol for in vitro propagation of vanilla using nodal explants by testing different concentrations of NAA and BAP, for the proliferation of the entire plant. Methods: Nodal explants with dormant axillary buds were obtained from year-old laboratory-grown Vanilla planifolia plants. MS media was prepared with a nutrient stock solution (containing macronutrients, micronutrients, iron solution and vitamins) and semi-solidified using phytagel. It was supplemented with different concentrations of NAA and BAP to induce multiple shoots and roots (0.5mg/L BAP with NAA at 0, 0.5, 1, 1.5, 2.0mg/L and vice-versa). The explants were sterilized, cultured in labelled test tubes and incubated at 26°C ± 2°C with 16/8 hours light/dark cycle. Data on shoot and root growth, leaf number, node number, and survival percentage were collected over three consecutive two-week periods. The data were square root transformed and subjected to ANOVA and LSD at a 5% significance level using the R statistical package. Results: Shoots emerged at 8 days and roots at 12 days after inoculation with 94% survival rate. It was discovered that for the NAA treatments, MS media supplemented with 2.00 mg/l NAA resulted in the highest shoot length (10.45cm), maximum root number (1.51), maximum shoot number (1.47) and the highest number of leaves (1.29). MS medium containing 1.00 mg/l NAA produced the highest number of nodes (1.62) and root length (14.27cm). Also, a similar growth pattern for the BAP treatments was observed. MS medium supplemented with 1.50 mg/l BAP resulted in the highest shoot length (14.98 cm), the highest number of nodes (4.60), the highest number of leaves (1.75) and the maximum shoot number (1.57). MS medium containing 0.50 mg/l BAP and 1.0 mg/l BAP generated a maximum root number (1.44) and the highest root length (13.25cm), respectively. However, the best concentration combination for maximizing shoot and root was media containing 1.5mg/l BAP combined with 0.5mg/l NAA, and 1.0mg/l NAA combined with 0.5mg/l of BAP respectively. These concentrations were optimum for in vitro growth and production of Vanilla planifolia. Significance: This study presents a standardized protocol for labs to produce clean vanilla plantlets, enhancing cultivation in Ghana and beyond. It provides insights into Vanilla planifolia's growth patterns and hormone responses, aiding future research and cultivation.

Keywords: Vanilla planifolia, In vitro propagation, plant hormones, MS media

Procedia PDF Downloads 39

Authors: Z. Yousefniayejahr, S. Bolognini, A. Bonini, C. Campobasso, N. Poma, F. Vivaldi, M. Di Luca, A. Tavanti, F. Di Francesco

Abstract:

Pathogenic bacteria represent a threat to healthcare systems and the food industry because their rapid detection remains challenging. Electrochemical biosensors are gaining prominence as a novel technology for the detection of pathogens due to intrinsic features such as low cost, rapid response time, and portability, which make them a valuable alternative to traditional methodologies. These sensors use biorecognition elements that are crucial for the identification of specific bacteria. In this context, bacteriophages are promising tools for their inherent high selectivity towards bacterial hosts, which is of fundamental importance when detecting bacterial pathogens in complex biological samples. In this study, we present the development of a low-cost and portable sensor based on the Zeno phage for the rapid detection of Staphylococcus aureus. Screen-printed gold electrodes functionalized with the Zeno phage were used, and electrochemical impedance spectroscopy was applied to evaluate the change of the charge transfer resistance (Rct) as a result of the interaction with S. aureus MRSA ATCC 43300. The phage-based biosensor showed a linear range from 101 to 104 CFU/mL with a 20-minute response time and a limit of detection (LOD) of 1.2 CFU/mL under physiological conditions. The biosensor’s ability to recognize various strains of staphylococci was also successfully demonstrated in the presence of clinical isolates collected from different geographic areas. Assays using S. epidermidis were also carried out to verify the species-specificity of the phage sensor. We only observed a remarkable change of the Rct in the presence of the target S. aureus bacteria, while no substantial binding to S. epidermidis occurred. This confirmed that the Zeno phage sensor only targets S. aureus species within the genus Staphylococcus. In addition, the biosensor's specificity with respect to other bacterial species, including gram-positive bacteria like Enterococcus faecium and the gram-negative bacterium Pseudomonas aeruginosa, was evaluated, and a non-significant impedimetric signal was observed. Notably, the biosensor successfully identified S. aureus bacterial cells in a complex matrix such as a nasal swab, opening the possibility of its use in a real-case scenario. We diluted different concentrations of S. aureus from 108 to 100 CFU/mL with a ratio of 1:10 in the nasal swap matrices collected from healthy donors. Three different sensors were applied to measure various concentrations of bacteria. Our sensor indicated high selectivity to detect S. aureus in biological matrices compared to time-consuming traditional methods, such as enzyme-linked immunosorbent assay (ELISA), polymerase chain reaction (PCR), and radioimmunoassay (RIA), etc. With the aim to study the possibility to use this biosensor to address the challenge associated to pathogen detection, ongoing research is focused on the assessment of the biosensor’s analytical performances in different biological samples and the discovery of new phage bioreceptors.

Keywords: electrochemical impedance spectroscopy, bacteriophage, biosensor, Staphylococcus aureus

Procedia PDF Downloads 52

Authors: S. Ping Ho, R. Dahal

Abstract:

The global economy has drastically changed how firms operate and compete. Although the construction industry is ‘local’ by its nature, the internationalization of the construction industry has become an inevitable reality. As a result of global competition, staying domestic is no longer safe from competition and, on the contrary, to grow and become an MNE (multi-national enterprise) becomes one of the important strategies for a firm to survive in the global competition. For the successful entrance into competing markets, the firms need to re-define their competitive advantages and re-identify the sources of the competitive advantages. A firm’s initiation of internationalization is not necessarily a result of strategic planning but also involves certain idiosyncratic events that pave the path leading to a firm’s internationalization. For example, a local firm’s incidental or unintentional collaboration with an MNE can become the initiating point of its internationalization process. However, because of the intensive competition in today’s global movement, many firms were compelled to initiate their internationalization as a strategic response to the competition. Understandingly stepping in in the process of internationalization and appropriately implementing the strategies (in the process) at different stages lead the construction firms to a successful internationalization journey. This study is carried out to develop a model of the internationalization process, which derives appropriate strategies that the construction firms can implement at each stage. The proposed model integrates two major and complementary views of internationalization and expresses the dynamic process of internationalization in three stages, which are the pre-international (PRE) stage, the foreign direct investment (FDI) stage, and the multi-national enterprise (MNE) stage. The strategies implied in the proposed model are derived, focusing on capability building, market locations, and entry modes based on the resource-based views: value, rareness, imitability, and substitutability (VRIN). With the proposed dynamic process model the potential construction firms which are willing to expand their business market area can be benefitted. Strategies for internationalization, such as core competence strategy, market selection, partner selection, and entry mode strategy, can be derived from the proposed model. The internationalization process is expressed in two different forms. First, we discuss the construction internationalization process, identify the driving factor/s of the process, and explain the strategy formation in the process. Second, we define the stages of internationalization along the process and the corresponding strategies in each stage. The strategies may include how to exploit existing advantages for the competition at the current stage and develop or explore additional advantages appropriate for the next stage. Particularly, the additionally developed advantages will then be accumulated and drive forward the firm’s stage of internationalization, which will further determine the subsequent strategies, and so on and so forth, spiraling up the stages of a higher degree of internationalization. However, the formation of additional strategies for the next stage does not happen automatically, and the strategy evolution is based on the firm’s dynamic capabilities.

Keywords: construction industry, dynamic capabilities, internationalization process, internationalization strategies, strategic management

Procedia PDF Downloads 43

Authors: B. Kriheli, E. Levner, T. C. E. Cheng, C. T. Ng

Abstract:

During the last decades, research interest in planning, scheduling, and control of emergency response operations, especially people rescue and evacuation from the dangerous zone of marine accidents, has increased dramatically. Until the survivors (called ‘targets’) are found and saved, it may cause loss or damage whose extent depends on the location of the targets and the search duration. The problem is to efficiently search for and detect/rescue the targets as soon as possible with the help of intelligent mobile robots so as to maximize the number of saved people and/or minimize the search cost under restrictions on the amount of saved people within the allowable response time. We consider a special situation when the autonomous mobile robots (AMR), e.g., unmanned aerial vehicles and remote-controlled robo-ships have no operator on board as they are guided and completely controlled by on-board sensors and computer programs. We construct a mathematical model for the search process in an uncertain environment and provide a new fast algorithm for scheduling the activities of the autonomous robots during the search-and rescue missions after an accident at sea. We presume that in the unknown environments, the AMR’s search-and-rescue activity is subject to two types of error: (i) a 'false-negative' detection error where a target object is not discovered (‘overlooked') by the AMR’s sensors in spite that the AMR is in a close neighborhood of the latter and (ii) a 'false-positive' detection error, also known as ‘a false alarm’, in which a clean place or area is wrongly classified by the AMR’s sensors as a correct target. As the general resource-constrained discrete search problem is NP-hard, we restrict our study to finding local-optimal strategies. A specificity of the considered operational research problem in comparison with the traditional Kadane-De Groot-Stone search models is that in our model the probability of the successful search outcome depends not only on cost/time/probability parameters assigned to each individual location but, as well, on parameters characterizing the entire history of (unsuccessful) search before selecting any next location. We provide a fast approximation algorithm for finding the AMR route adopting a greedy search strategy in which, in each step, the on-board computer computes a current search effectiveness value for each location in the zone and sequentially searches for a location with the highest search effectiveness value. Extensive experiments with random and real-life data provide strong evidence in favor of the suggested operations research model and corresponding algorithm.

Keywords: disaster management, intelligent robots, scheduling algorithm, search-and-rescue at sea

Procedia PDF Downloads 158

Authors: Amelia Frickey, Timothy (TJ) Sheridan, Angelica Rossi, Bahar Aliakbarian

Abstract:

The growth of large food supply chains demanded improved end-to-end traceability of food products, which has led to companies being increasingly interested in using smart technologies such as Radio Frequency Identification (RFID)-enabled packaging to track items. As technology is being widely used, there are several technological or economic issues that should be overcome to facilitate the adoption of this track-and-trace technology. One of the technological challenges of RFID technology is its sensitivity to different environmental form factors, including packaging materials and the content of the packaging. Although researchers have assessed the performance loss due to the proximity of water and aqueous solutions, there is still the need to further investigate the impacts of food products on the reading range of RFID tags. However, to the best of our knowledge, there are not enough studies to determine the correlation between RFID tag performance and food beverages properties. The goal of this project was to investigate the effect of the solution properties (pH and conductivity) and different packaging materials filled with food-like water-based solutions on the performance of an RFID tag. Three commercially available ultra high-frequency RFID tags were placed on three different bottles and filled with different concentrations of water-based solutions, including sodium chloride, citric acid, sucrose, and ethanol. Transparent glass, Polyethylneterephtalate (PET), and Tetrapak® were used as the packaging materials commonly used in the beverage industries. Tag readability (Theoretical Read Range, TRR) and sensitivity (Power on Tag Forward, PoF) were determined using an anechoic chamber. First, the best place to attach the tag for each packaging material was investigated using empty and water-filled bottles. Then, the bottles were filled with the food-like solutions and tested with the three different tags and the PoF and TRR at the fixed frequency of 915MHz. In parallel, the pH and conductivity of solutions were measured. The best-performing tag was then selected to test the bottles filled with wine, orange, and apple juice. Despite various solutions altering the performance of each tag, the change in tag performance had no correlation with the pH or conductivity of the solution. Additionally, packaging material played a significant role in tag performance. Each tag tested performed optimally under different conditions. This study is the first part of comprehensive research to determine the regression model for the prediction of tag performance behavior based on the packaging material and the content. More investigations, including more tags and food products, are needed to be able to develop a robust regression model. The results of this study can be used by RFID tag manufacturers to design suitable tags for specific products with similar properties.

Keywords: smart food packaging, supply chain management, food waste, radio frequency identification

Procedia PDF Downloads 98

Authors: Rajkumar Ghosh

Abstract:

Fluoride contamination in water and its subsequent impact on agricultural practices is a growing concern in various regions worldwide, including North 24 Parganas, West Bengal, India. This study aimed to investigate the extent of fluoride contamination in the region's water sources and evaluate its effects on crop production and quality. A comprehensive survey of water sources, including wells, ponds, and rivers, was conducted to assess the fluoride levels in North 24 Parganas. Water samples were collected and analyzed using standard methods, and the fluoride concentration was determined. The findings revealed significant fluoride contamination in the water sources, surpassing the permissible limits recommended by national and international standards. To assess the effects of fluoride contamination on crops, field experiments were carried out in selected agricultural areas. Various crops commonly cultivated in the region, such as paddy, wheat, vegetables, and fruits, were examined for their growth, yield, and nutritional quality parameters. Additionally, soil samples were collected from the study sites to analyse the fluoride levels and their potential impact on soil health. The results demonstrated the adverse effects of fluoride contamination on crop growth and yield. Reduced plant height, stunted root development, decreased biomass accumulation, and diminished crop productivity were observed in fluoride-affected areas compared to uncontaminated control sites. Furthermore, the nutritional composition of crops, including micronutrients and mineral content, was significantly altered under high fluoride exposure, leading to potential health risks for consumers. The study also assessed the impact of fluoride on soil quality and found a negative correlation between fluoride concentration and soil health indicators, such as pH, organic matter content, and nutrient availability. These findings emphasize the need for sustainable soil management practices to mitigate the harmful effects of fluoride contamination and maintain agricultural productivity. Overall, this study highlights the alarming issue of fluoride contamination in water sources and its detrimental effects on crop production and quality in North 24 Parganas, West Bengal, India. The findings underscore the urgency for implementing appropriate water treatment measures, promoting awareness among farmers and local communities, and adopting sustainable agricultural practices to mitigate fluoride contamination and safeguard the region's agricultural ecosystem.

Keywords: agricultural ecosystem, water treatment, sustainable agricultural, fluoride contamination

Procedia PDF Downloads 61

Authors: Maria Cristina Tommaso, Maria Das Graças L. Silva, Carlos Jose Pacheco

Abstract:

Have the advances of the Brazilian legislation reflected or have been consonant with the inclusion of PwD in higher education? In 1990 the World Declaration on Education for All, a document organized by the United Nations Educational, Scientific and Cultural Organization (UNESCO), stated that the basic learning needs of people with disabilities, as they were called, required special attention. Since then, legislation in signatory countries such as Brazil has made considerable progress in guaranteeing, in a gradual and increasing manner, the rights of persons with disabilities to education. Principles, policies, and practices of special educational needs were created and guided action at the regional, national and international levels on the structure of action in Special Education such as administration, recruitment of educators and community involvement. Brazilian Education Law No. 3.284 of 2003 ensures inclusion of people with disabilities in Brazilian higher education institutions and also in 2015 the Law 13,146/2015 - Brazilian Law on the Inclusion of Persons with Disabilities (Statute of the Person with Disabilities) regulates the inclusion of PwD by the guarantee of their rights. This study analyses data related to people with disability inclusion in High Education in the south region of Rio de Janeiro State - Brazil during the period between 2008 and 2018, based in its correlation with the changes in the Brazilian legislation in the last ten years that were subjected by PwD inclusion processes in the Brazilian High Education Systems. The region studied is composed by sixteen cities and this research refers to the largest one, Volta Redonda that represents 25 percent of the total regional population. The PwD reception process had the dicing data at the Volta Redonda University Center with 35 percent of high education students in this territorial area. The research methodology analyzed the changes occurring in the legislation about the inclusion of people with disability in High Education in the last ten years and its impacts on the samples of this study during the period between 2008 and 2018. It was verified an expressive increasing of the number of PwD students, from two in 2008 to 190 PwD students in 2018. The data conclusions are presented in quantitative terms and the aim of this study was to verify the effectiveness of the PwD inclusion in High Education, allowing visibility of this social group. This study verified that the fundamental human rights guarantees have a strong relation to the advances of legislation and the State as a guarantor instance of the rights of the people with disability and must be considered a mean of consolidation of their education opportunities isonomy. The recognition of full rights and the inclusion of people with disabilities requires the efforts of those who have decision-making power. This study aimed to demonstrate that legislative evolution is an effective instrument in the social integration of people with disabilities. The study confirms the fundamental role of the state in guaranteeing human rights and demonstrates that legislation not only protects the interests of vulnerable social groups, but can also, and this is perhaps its main mission, to change behavior patterns and provoke the social transformation necessary to the reduction of inequality of opportunity.

Keywords: high education, inclusion, legislation, people with disability

Procedia PDF Downloads 137

Authors: Chux Gervase Iwu, Simon Nsengimane

Abstract:

Entrepreneurship stimulates socio-economic development in many countries, if not all. It creates jobs and decreases unemployment and inequality. There are other benefits that are accruable from entrepreneurship, namely the empowerment of women and the promotion of better livelihoods. Innovation has become a weapon for business competition, growth, and sustainability. Paradoxically, it is a threat to businesses because products can be duplicated; new products may decrease the market share of existing ones or delete them from the market. This creates a constant competitive environment that calls for updates, innovation, and the invention of new products and services. Thus, the importance of higher education in instilling a good entrepreneurial mindset in students has become even more critical. It can be argued that the business environment is under enormous pressure from several factors, including the fourth industrial revolution, which calls for the adoption and use of information and communication technology, which is the catalyst for many innovations and organisational changes. Therefore, it is crucial that higher education students are equipped with relevant knowledge and skills to respond effectively to the needs of the business environment and create a vibrant entrepreneurship ecosystem. In South Africa, entrepreneurship education or some form of it has been a privilege for economic and management fields of study, leaving behind other fields. Entrepreneurship should not be limited to business faculties but rather extended to other fields of study. This is perhaps the reason for low levels of entrepreneurship uptake among South African graduates if they are compared with the graduates in other countries. There may be other reasons for the low entrepreneurship uptake. Some of these have been documented in extant literature to include (1) not enough time was spent teaching entrepreneurship in the business faculties, (2) the skills components in the curricula are insufficient, and (3) the overall attitudes/mindsets necessary to establish and run sustainable enterprises seem absent. Therefore, four important areas are recognised as crucial for the effective implementation of entrepreneurship education: policy, private sector engagement, curriculum development, and teacher development. The purpose of this research is to better comprehend the views, aspirations, and expectations of students and faculty members to design an entrepreneurial teaching model for higher education institutions. A qualitative method will be used to conduct a purposive interview with undergraduate and graduate students in select higher institutions. Members of faculty will also be included in the sample as well as, where possible, two or more government personnel responsible for higher education policy development. At present, interpretative analysis is proposed for the analysis of the interviews with the support of Atlas Ti. It is hoped that an entrepreneurship education model in the South African context is realised through this study.

Keywords: entrepreneurship education, higher education institution, graduate unemployment, curriculum development

Procedia PDF Downloads 59

Authors: Zoi Konsoula

Abstract:

The increasing prevalence of Alzheimer’s disease (AD) and diabetes mellitus (DM) constitutes them major global health problems. Recently, the inhibition of key enzyme activity is considered a potential treatment of both diseases. Specifically, inhibition of acetylcholinesterase (AChE), the key enzyme involved in the breakdown of the neurotransmitter acetylcholine, is a promising approach for the treatment of AD, while inhibition of α-amylase retards the hydrolysis of carbohydrates and, thus, reduces hyperglycemia. Unfortunately, commercially available AChE and α-amylase inhibitors are reported to possess side effects. Consequently, there is a need to develop safe and effective treatments for both diseases. In the present study, pomegranate peel (PP) was extracted using various solvents of increasing polarity, while two extraction methods were employed, the conventional maceration and the ultrasound assisted extraction (UAE). The concentration of bioactive phytoconstituents, such as total phenolics (TPC) and total flavonoids (TFC) in the prepared extracts was evaluated by the Folin-Ciocalteu and the aluminum-flavonoid complex method, respectively. Furthermore, the anti-neurodegenerative and anti-hyperglycemic activity of all extracts was determined using AChE and α-amylase inhibitory activity assays, respectively. The inhibitory activity of the extracts against AChE and α-amylase was characterized by estimating their IC₅₀ value using a dose-response curve, while galanthamine and acarbose were used as positive controls, respectively. Finally, the kinetics of AChE and α-amylase in the presence of the most inhibitory potent extracts was determined by the Lineweaver-Burk plot. The methanolic extract prepared using the UAE contained the highest amount of phytoconstituents, followed by the respective ethanolic extract. All extracts inhibited acetylcholinesterase in a dose-dependent manner, while the increased anticholinesterase activity of the methanolic (IC₅₀ = 32 μg/mL) and ethanolic (IC₅₀ = 42 μg/mL) extract was positively correlated with their TPC content. Furthermore, the activity of the aforementioned extracts was comparable to galanthamine. Similar results were obtained in the case of α-amylase, however, all extracts showed lower inhibitory effect on the carbohydrate hydrolyzing enzyme than on AChE, since the IC₅₀ value ranged from 84 to 100 μg/mL. Also, the α-amylase inhibitory effect of the extracts was lower than acarbose. Finally, the methanolic and ethanolic extracts prepared by UAE inhibited both enzymes in a mixed (competitive/noncompetitive) manner since the Kₘ value of both enzymes increased in the presence of extracts, while the Vmax value decreased. The results of the present study indicate that PP may be a useful source of active compounds for the management of AD and DM. Moreover, taking into consideration that PP is an agro-industrial waste product, its valorization could not only result in economic efficiency but also reduce the environmental pollution.

Keywords: acetylcholinesterase, Alzheimer’s disease, α-amylase, diabetes mellitus, pomegranate

Procedia PDF Downloads 108

Authors: Mohammed Khalil Ur Rahman, Mohammed Alsharon, Arshad Muktar, Zahid Shaik

Abstract:

Any ailment can go into terminal stages, cancer being one such disease which is many times detected in latent stages. Cancer is often characterized by constitutional symptoms which are agonizing in nature which disturbs patients and their family as well. In order to relieve such intolerable symptoms treatment modality employed is known to be ‘Palliative Care’. The goal of palliative care is to enhance patient’s quality of life by relieving or rather reducing the distressing symptoms of patients such as pain, nausea/ vomiting, anorexia/loss of appetite, excessive salivation, mouth ulcers, weight loss, constipation, oral thrush, emaciation etc. which are due to the effect of disease or due to the undergoing treatment such as chemotherapy, radiation etc. Ayurveda and Unani as well as other traditional medicines is getting more and more international attention in recent years and Ayurveda and Unani holistic perspective of the disease, it seems that there are many herbs and herbomineral preparation which can be employed in the treatment of malignancy and also in palliative care. Though many of them have yet to be scientifically proved as anti-cancerous but there is definitely a positive lead that some of these medications relieve the agonising symptoms thereby making life of the patient easy. Health is viewed in Islam in a holistic way. One of the names of the Quran is al-shifa' meaning ‘that which heals’ or ‘the restorer of health’ to refer to spiritual, intellectual, psychological, and physical health. The general aim of medical science, according to Islam, is to secure and adopt suitable measures which, with Allah’s permission, help to preserve or restore the health of the human body. Islam motivates the Physician to view the patient as one organism. The patient has physical, social, psychological, and spiritual dimensions that must be considered in synthesis with an integrated, holistic approach. Aims & Objectives: - To suggest herbs which are mentioned in Ayurveda Unani with potential palliative activity in case of Cancer patients. - Most of tibb nabawi [Prophetic Medicine] is preventive medicine and must have been divinely inspired. - Spiritual Aspects of Healing: Prayer, dua, recitation of the Quran - Remembrance of Allah play a central role.Materials & Method: Literary review of the herbs supported with experiential evidence will be discussed. Discussion: On the basis of collected data subject will be discussed in length. Conclusion: Will be presented in paper.

Keywords: palliative care, holistic, Ayurvedic and Unani traditional system of medicine, Quran, hadith

Procedia PDF Downloads 329

Authors: Karen Fuchs, Michael Prokein, Nils Mölders, Manfred Renner, Eckhard Weidner

Abstract:

Due to the high CO₂ emissions, the energy consumption for the production of sand-lime bricks is of great concern. Especially the production of quicklime from limestone and the energy consumption for hydrothermal curing contribute to high CO₂ emissions. Hydrothermal curing is carried out under a saturated steam atmosphere at about 15 bar and 200°C for 12 hours. Therefore, we are investigating the opportunity to replace quicklime and sand in the production of building materials with different types of slag as calcium-rich waste from steel production. We are also investigating the possibility of substituting conventional hydrothermal curing with CO₂ curing. Six different slags (Linz-Donawitz (LD), ferrochrome (FeCr), ladle (LS), stainless steel (SS), ladle furnace (LF), electric arc furnace (EAF)) provided by "thyssenkrupp MillServices & Systems GmbH" were ground at "Loesche GmbH". Cylindrical blocks with a diameter of 100 mm were pressed at 12 MPa. The composition of the blocks varied between pure slag and mixtures of slag and sand. The effects of pressure, temperature, and time on the CO₂ curing process were studied in a 2-liter high-pressure autoclave. Pressures between 0.1 and 5 MPa, temperatures between 25 and 140°C, and curing times between 1 and 100 hours were considered. The quality of the CO₂-cured blocks was determined by measuring the compressive strength by "Ruhrbaustoffwerke GmbH & Co. KG." The degree of carbonation was determined by total inorganic carbon (TIC) and X-ray diffraction (XRD) measurements. The pH trends in the cross-section of the blocks were monitored using phenolphthalein as a liquid pH indicator. The parameter set that yielded the best performing material was tested on all slag types. In addition, the method was scaled to steel slag-based building blocks (240 mm x 115 mm x 60 mm) provided by "Ruhrbaustoffwerke GmbH & Co. KG" and CO₂-cured in a 20-liter high-pressure autoclave. The results show that CO₂ curing of building blocks consisting of pure wetted LD slag leads to severe cracking of the cylindrical specimens. The high CO₂ uptake leads to an expansion of the specimens. However, if LD slag is used only proportionally to replace quicklime completely and sand proportionally, dimensionally stable bricks with high compressive strength are produced. The tests to determine the optimum pressure and temperature show 2 MPa and 50°C as promising parameters for the CO₂ curing process. At these parameters and after 3 h, the compressive strength of LD slag blocks reaches the highest average value of almost 50 N/mm². This is more than double that of conventional sand-lime bricks. Longer CO₂ curing times do not result in higher compressive strengths. XRD and TIC measurements confirmed the formation of carbonates. All tested slag-based bricks show higher compressive strengths compared to conventional sand-lime bricks. However, the type of slag has a significant influence on the compressive strength values. The results of the tests in the 20-liter plant agreed well with the results of the 2-liter tests. With its comparatively moderate operating conditions, the CO₂ curing process has a high potential for saving CO₂ emissions.

Keywords: CO₂ curing, carbonation, CCU, steel slag

Procedia PDF Downloads 91

Authors: Ma. Cecilia D. Licuan

Abstract:

The pandemic situation continues to affect the lives of many people, including children with disabilities and their families, globally, especially in developing countries like the Philippines. The operations of health programs, industries, and economic sectors, as well as academic training institutions, are still challenged in terms of operations and delivery of services. The academic community of the Physical Therapy program is not spared by this circumstance. The restriction posted by the quarantine policies nearly terminated the onsite delivery of training programs for the senior internship level, which challenged the academic institutions to implement flexible learning programs to ensure the continuity of the instructional and learning processes with full consideration of safety and compliance to health protocols. This study aimed to develop a benchmark model that can be used by tertiary-level health institutions in the implementation of the Pediatric Senior Clinical Internship Training Program using Telerehabilitation. It is a descriptive-qualitative paper that utilized documentary analysis and focused on explaining the design, development, and implementation processes used by De La Salle Medical and Health Sciences Institute – College of Rehabilitation Sciences (DLSMHSI-CRS) Physical Therapy Department in its Pediatric Cluster Senior Clinical Internship Training Program covering the pandemic years spanning from the academic year 2020- 2021 to present anchored on needs analysis based on documentary reviews. Results of the study yielded the determination of the Pediatric Telerehabilitation Model; declaration of developed training program outcomes and thrusts and content; explanation of the process integral to the training program’s pedagogy in implementation; and the evaluation procedures conducted for the program. Since the study did not involve human participants, ethical considerations on the use of documents for review were done upon the endorsement of the management of the DLSMHSI-CRS to conduct the study. This paper presents the big picture of how a tertiary-level health sciences institution in the Philippines embraced the senior clinical internship challenges through the operations of its telerehabilitation program. It specifically presents the design, development and implementation processes used by De La Salle Medical and Health Sciences Institute – College of Rehabilitation Sciences Physical Therapy Department in its Pediatric Cluster Senior Clinical Internship Training Program, which can serve as a benchmark model for other institutions as they continue to serve their stakeholders amidst the pandemic.

Keywords: pediatric physical therapy, telerehabilitation, clinical internship, pandemic

Procedia PDF Downloads 106

Authors: Prajakta Khare

Abstract:

There is a huge number of social enterprises operating in India, across all enterprise sizes and forms addressing diverse social issues. Some cases such as such as Aravind eye care, Narayana Hridalaya, SEWA have been studied extensively in management literature and are known cases in social entrepreneurship. But there are several smaller social enterprises in India that are not called so per se due to the lack of understanding of the concept. There is a lack of academic research on social entrepreneurship in India and the term ‘social entrepreneurship’ is not yet widely known in the country, even by people working in this field as was found by this study. The present study aims to identify the most prominent form of social enterprises in India, the profile of the entrepreneurs, challenges faced, the lessons (theory and practices) emerging from their functioning and finally the factors contributing to the enterprises’ success. This is a preliminary exploratory study using primary data from 30 social enterprises in India. The study used snow ball sampling and a qualitative analysis. Data was collected from founders of social enterprises through written structured questionnaires, open-ended interviews and field visits to enterprises. The sample covered enterprises across sectors such as environment, affordable education, children’s rights, rain water harvesting, women empowerment etc. The interview questions focused on founder’s background and motivation, qualifications, funding, challenges, founder’s understanding and perspectives on social entrepreneurship, government support, linkages with other organizations etc. apart from several others. The interviews were conducted across 3 languages - Hindi, Marathi, English and were then translated and transcribed. 50% of founders were women and 65% of the total founders were highly qualified with a MBA, PhD or MBBS. The most important challenge faced by these entrepreneurs is recruiting skilled people. When asked about their understanding of the term, founders had diverse perspectives. Also, their understandings about the term social enterprise and social entrepreneur were extremely varied. Some founders identified the terms with doing something good for the society, some thought that every business can be called a social enterprise. 35% of the founders were not aware of the term social entrepreneur/ social entrepreneurship. They said that they could identify themselves as social entrepreneurs after discussions with the researcher. The general perception in India is that ‘NGOs are corrupt’- fighting against this perception to secure funds is also another problem as pointed out by some founders. There are unique challenges that social entrepreneurs in India face, as the political, social, economic environment around them is rapidly changing; and getting adequate support from the government is a problem. The research in its subsequent stages aims to clarify existing, missing and new definitions of the term to provide deeper insights in the terminology and issues relating to Social Entrepreneurship in India.

Keywords: challenges, India, social entrepreneurship, social entrepreneurs

Procedia PDF Downloads 453

Authors: Le Jiang, Chua Jinxing

Abstract:

Introduction: The recent outbreak of Ebola virus disease in the west Africa has drawn global concern. With a high fatality rate and direct human-to-human transmission, it has spread between countries and caused great damages for patients and family who are affected. Being the designated hospital to manage epidemic outbreak in Singapore, Tan Tock Seng Hospital (TTSH) is facing great challenges in preparation and managing of potential outbreak of emerging infectious disease such as Ebola virus disease. Aim: We conducted an infection control drill in TTSH emergency department to assess the readiness of healthcare and allied health workers in managing suspected Ebola patients. It also helps to review current Ebola clinical protocol and work instruction to ensure more smooth and safe practice in managing Ebola patients in TTSH emergency department. Result: General preparedness level of staffs involved in managing Ebola virus disease in TTSH emergency department is not adequate. Knowledge deficits of staffs on Ebola personal protective equipment gowning and degowning process increase the risk of potential cross contamination in patient care. Loopholes are also found in current clinical protocol, such as unclear instructions and inaccurate information, which need to be revised to promote better staff performance in patient management. Logistic issues such as equipment dysfunction and inadequate supplies can lead to ineffective communication among teams and causing harm to patients in emergency situation. Conclusion: The infection control drill identified the need for more well-structured and clear clinical protocols to be in place to promote participants performance. In addition to quality protocols and guidelines, systemic training and annual refresher for all staffs in the emergency department are essential to prepare staffs for the outbreak of Ebola virus disease. Collaboration and communication with allied health staffs are also crucial for smooth delivery of patient care and minimising the potential human suffering, properties loss or injuries caused by disease. Therefore, more clinical drills with collaboration among various departments involved are recommended to be conducted in the future to monitor and assess readiness of TTSH emergency department in managing Ebola virus disease.

Keywords: ebola, emergency department, infection control drill, Tan Tock Seng Hospital

Procedia PDF Downloads 102

Authors: Nino Kobakhidze, Endi Varsimashvili, Davit Makadze

Abstract:

The Caucasus is a link of the Alpine-Himalayan fold belt and involves the Greater Caucasus and the Lesser Caucasus fold systems and the Intermountain area. The study object is located within the northernmost part of the Lesser Caucasus orogen, in the eastern part of Achara-Trialeti fold -thrust belt. This area was rather well surveyed in 70th of the twentieth century in terms of oil-and-gas potential, but to our best knowledge, detailed sedimentological studies have not been conducted so far. In order to fill this gap, the authors of the present thesis started research in this direction. One of the objects selected for the research was the deposits of the Kavtura river valley situated on the northern slope of the Trialeti ridge. Paleocene-Lower Eocene deposits known in scientific literature as ‘Borjomi Flysch’ (Turbidites) are exposed in the mentioned area. During the research, the following methodologies were applied: selection of key cross sections, a collection of rock samples, microscopic description of thin sections, mineralogical and petrological analysis of material and identification of trace fossils. The study of Paleocene-Lower Eocene deposits starts with Kavtura river valley in the east, where they are well characterized by microfauna. The cross-section of the deposits starts with Danian variegated marlstone conformably overlain by the alternation of thick and thin-bedded sandstones (thickness 40-50 cm). They are continued with interbedded of thin-bedded sandstones and shales(thickness 4-5 m). On the sole surface of sandstones ichnogenera ‘Helmintopsis’ and ‘Scolicia’ are recorded and within the bed –‘Chondrites’ is found. Towards the Riverhead, there is a 1-2 m gap in sedimentation; then again the Paleocene-Lower Eocene sediments crop out. They starting with alternation of grey-green medium-grained sandstones and shales enclosing dark color plant detritus. They are overlain by the interbedded of calcareous sandstones and marls, where the thickness of sandstones is variable (20-70 cm). Ichnogenus – ‘Scolicia’ is found here. Upwards the above-mentioned deposits pass into Middle Eocenian volcanogenic-sedimentary suits. In the Kavtura river valley, the thickness of the Paleocene-Lower Eocene deposits is 300-400 m. In the process of research, the following activities are conducted: the facial analysis of host rocks, correlation of the study section with other cross sections and interpretation of depositional environment of the area. In the area the authors have found and described ichnogenera; their preliminary determination have shown that they belong to pre-depositional (‘Helmintopsis’) and post-depositional (‘Chondrites’) forms. As known, during the Cretaceous-Paleogene time, the Achara-Trialeti fold-thrust belt extensional basin was the accumulation area with great thicknesses (from shallow to deep marine sediments). It is confirmed once more by the authors investigations preliminary results of paleoichnological studies inclusive.

Keywords: flysh deposits, lithology, The Lesser Caucasus, trace fossils

Procedia PDF Downloads 148

Authors: Hossein Rezaie

Abstract:

Academic institutions, esp. universities, have been known as cradles of learning and teaching great thinkers while creating the type of knowledge that is supposed to be bereft of utilitarian motives. Nonetheless, it seems that such intellectual centers have entered into a competition with each other for attracting the attention of potential clients. The traditional values of (higher) education such as nurturing criticality and fostering intellectuality in students have been replaced with strategic planning, quality assurance, performance assessment, and academic audits. Not being immune from the whims and wishes of marketization, the system of higher education in the UK has been recalibrated by policy makers to address the demand and supply of student education, academic research and other university activities on the basis of monetary factors. As an immediate example in this vein, the Russell Group in the UK, which is comprised of 24 leading UK research universities, has explicitly expressed it policy on its official website as follows: ‘Russell Group universities are global businesses competing for staff, students and funding with the best in the world’. Furthermore, certain attempts have been made to corporatize the system of HE which have been manifested in remodeling of university governing bodies on corporate lines and developing measurement scales for indicating the performance of teaching practitioners. Nevertheless, it seems that such structural changes in policies toward the system of HE have bearing on the practices of practitioners and educators as well as the identity of students who are the customers of educational services. The effects of marketization have been examined mainly in terms of students’ perceptions and motivation, institutional policies and university management. However, the teaching practitioner side seems to be an under-studied area with regard to any changes in its expectations, satisfaction and perception of professional identity in the aftermath of introducing market-wise values into HE of the UK. As a result, this research aims to investigate the possible outcomes of market-driven values on the practitioner side of HE in the UK and finally seeks to address the following research questions: 1-How is the change in the mission of HE in the UK reflected in institutional documents? 1-A- How is the change of mission represented in job adverts? 1-B- How is the change of mission represented in university prospectuses? 2-How are teaching practitioners represented regarding their roles and obligations in the prospectuses and job ads published by UK HE institutions? In order to address these questions, the researcher will analyze 30 prospectuses and job ads published by Russel Group universities by taking Critical Discourse Analysis as his point of departure and the analytical methods of genre analysis and Systemic Functional Linguistics to probe into the generic features and representation of participants, in this case teaching practitioners, in the selected corpus.

Keywords: higher education, job advertisements, marketization of higher education, prospectuses

Procedia PDF Downloads 232

Authors: Amir Nourbakhsh Habibabadi, Alireza Ashori

Abstract:

Context: The growing concern over the management of plastic waste and the high demand for wood-based products have led to the development of wood-plastic composites. Agricultural residues, which are abundantly available, can be used as a source of lignocellulosic fibers in the production of these composites. The use of recycled polymers and nanomaterials is also a promising approach to enhance the mechanical and physical properties of the composites. Research Aim: The aim of this study was to investigate the feasibility of using recycled high-density polyethylene (rHDPE), polypropylene (rPP), and agricultural residues fibers for manufacturing wood-plastic nano-composites. The effects of these materials on the mechanical properties of the composites, specifically tensile and flexural strength, were studied. Methodology: The study utilized an experimental approach where extruders and hot presses were used to fabricate the composites. Five types of cellulosic residues fibers (bagasse, corn stalk, rice straw, sunflower, and canola stem), three levels of nanomaterials (carbon nanotubes, nano silica, and nanoclay), and coupling agent were used to chemically bind the wood/polymer fibers, chemicals, and reinforcement. The mechanical properties of the composites were then analyzed. Findings: The study found that composites made with rHDPE provided moderately superior tensile and flexural properties compared to rPP samples. The addition of agricultural residues in several types of wood-plastic nano-composites significantly improved their bending and tensile properties, with bagasse having the most significant advantage over other lignocellulosic materials. The use of recycled polymers, agricultural residues, and nano-silica resulted in composites with the best strength properties. Theoretical Importance: The study's findings suggest that using agricultural fiber residues as reinforcement in wood/plastic nanocomposites is a viable approach to improve the mechanical properties of the composites. Additionally, the study highlights the potential of using recycled polymers in the development of value-added products without compromising the product's properties. Data Collection and Analysis Procedures: The study collected data on the mechanical properties of the composites using tensile and flexural tests. Statistical analyses were performed to determine the significant effects of the various materials used. Question addressed: Can agricultural residues and recycled polymers be used to manufacture wood-plastic nano-composites with enhanced mechanical properties? Conclusion: The study demonstrates the feasibility of using agricultural residues and recycled polymers in the production of wood-plastic nano-composites. The addition of these materials significantly improved the mechanical properties of the composites, with bagasse being the most effective agricultural residue. The study's findings suggest that composites made from recycled materials can offer value-added products without sacrificing performance.

Keywords: polymer, composites, wood, nano

Procedia PDF Downloads 59

Authors: Kalsoom Shaikh, Ghulam Sarwar Gachal, Saima Memon

Abstract:

Our study aimed to assess diversity and habitats of amphibian fauna in Sindh province as amphibians are among most vulnerable animals and the risk of their extinction is increasing in many parts of world mainly due to habitat degradation. Present study consisted of field surveys and laboratory analytical work; field surveys were carried out to confirm amphibian diversity and collection of water samples from their habitats, whereas laboratory work was conducted for identification of species and analysis of water quality of habitats through physico-chemical parameters. For identification of amphibian species, morphology was thoroughly examined using taxonomic key, whereas water quality was assessed via physico-chemical parameters including pH, electric conductivity (EC), total dissolved solids (TDS), total hardness (T. Hard), total alkalinity (T. Alk), chloride (Cl), carbon dioxide (CO₂), sulfate (SO₄), phosphate (PO₄), nitrite (NO₂) and nitrate (NO₃) using material and methods of analytical grade. pH value was analyzed using pH meter, whereas levels of EC and TDS were recorded using conductivity meter and TDS meter, respectively. Other parameters with exception of non-metallic parameters (SO₄, PO₄, NO₂, and NO₃) were analyzed through distinct titration methods. Concentration of non-metallic parameters was evaluated using ultra-violet spectrophotometer. This study revealed existence of four amphibian species including Hoplobatrachus tigerinus, Euphlyctis cyanophlyctis, Allopa hazarensis belonging to Family Ranidae and Bufo stomaticus (Family Bufonidae) randomly distributed in district Ghotki, Jamshoro, Kashmor, Larkana, Matiari and Shikarpur in Sindh. Assessment of aquatic habitats in different areas found value of parameters as followed: Habitats in district Ghoki (pH: 7.8 ± 0.3, EC: 2165.3 ± 712.6, TDS: 1507.0 ± 413.1, T-Hard: 416.4 ± 67.5, T. Alk: 393.4 ± 78.4, Cl: 362.4 ± 70.1, CO₂: 21.1 ± 3.5, SO₄: 429.3 ± 100.1, PO₄: 487.5 ± 122.5, NO₂: 13.7 ± 1.0, NO₃: 14.7 ± 2.5), district Jamshoro habitats (pH: 8.1 ± 0.4, EC: 2403.8 ± 55.4, TDS: 1697.2 ± 77.0, T. Hard: 548.7 ± 43.2, T. Alk: 294.4 ± 29.0, Cl: 454.7 ± 50.8 CO₂: 16.9 ± 2.4, SO₄: 713.0 ± 49.3, PO₄: 826.2 ± 53.0, NO₂: 15.2 ± 3.4, NO₃: 21.6 ± 3.7), habitats in Kashmor district (pH: 8.0 ± 0.5, EC: 2450.3 ± 610.9, TDS: 1745.3 ± 440.9, T. Hard: 624.6 ± 305.8, T. Alk: 445.7 ± 120.5, Cl: 448.9 ± 128.8, CO₂: 18.9 ± 4.5, SO₄: 619.8 ± 205.8, PO₄: 474.1 ± 94.2, NO₂: 15.2 ± 3.1, NO₃ 14.3 ± 2.6), district Larkana habitats (pH: 8.4 ± 0.4, EC: 2555.8 ± 70.3, TDS: 1784.4 ± 36.9, T. Hard: 623.0 ± 42.5, T. Alk: 329.6 ± 36.7, Cl: 614.3 ± 89.5, CO₂: 17.6 ± 1.2, SO₄: 845.1 ± 67.6, PO₄: 895.0 ± 61.4, NO₂: 13.6 ± 3.8, NO₃: 23.1 ± 2.8), district Matiari habitats (pH: 8.0 ± 0.4 EC: 2492.3 ± 928.1, TDS: 430.0 ± 161.3, T. Hard: 396.7 ± 183.3, T. Alk: 388.1 ± 97.4, Cl: 551.6 ± 73.4, CO₂: 15.8 ± 2.9, SO₄: 576.5 ± 200.0, PO₄: 434.7 ± 100.6, NO₂: 15.8 ± 2.9, NO₃: 15.2 ± 3.0) and habitats in Shikarpur district (pH: 8.1 ± 0.6, EC: 2191.7 ± 765.1, TDS: 1764.9 ± 409.2, T. Hard: 431.9 ± 68.4,T. Alk: 350.3 ± 44.3, Cl: 381.5 ± 29.5, CO₂: 18.0 ± 4.0, SO₄: 518.8 ± 97.9, PO₄: 493.6 ± 64.6, NO₂: 14.0 ± 0.8, NO₃: 16.1 ± 2.8). Values of physico-chemical parameters were found higher than permissible level of Environmental Protectiona Agency (EPA). Monthly variation in concentration of physico-chemical parameters was also prominently recorded at all the study locals. This study discovered poor diversity of amphibian fauna and condition of their habitats was also observed as pitiable. This study established base line information that may be used in execution of an effective management plan and future monitoring of amphibian diversity and their habitats in Sindh.

Keywords: amphibians, diversity, habitats, Pakistan, Sindh

Procedia PDF Downloads 147

Authors: Dmytro Symak

Abstract:

The experience in other countries shows that, the role of accreditation of higher education as one of the types of quality assurance process for providing educational services increases. This was the experience of highly developed countries such as USA, Canada, France, Germany, because without proper quality assurance process is impossible to achieve a successful future of the nation and the state. In most countries, the function of Higher Education Accreditation performs public authorities, in particular, such as the Ministry of Education. In the US, however, the quality assurance process is independent on the government and implemented by private non-governmental organization - the Council of Higher Education Accreditation. In France, the main body that carries out accreditation of higher education is the Ministry of National Education. As part of the Bologna process is the mutual recognition and accreditation of degrees. While higher education institutions issue diplomas, but the ministry could award the title. This is the main level of accreditation awarded automatically by state universities. In total, there are in France next major level of accreditation of higher education: - accreditation for a visa: Accreditation second level; - recognition of accreditation: accreditation of third level. In some areas of education to accreditation ministry should adopt formal recommendations on specific organs. But there are also some exceptions. Thus, the French educational institutions, mainly large Business School, looking for non-French accreditation. These include, for example, the Association to Advance Collegiate Schools of Business, the Association of MBAs, the European Foundation for Management Development, the European Quality Improvement System, a prestigious EFMD Programme accreditation system. Noteworthy also German accreditation system of education. The primary here is a Conference of Ministers of Education and Culture of land in the Federal Republic of Germany (Kultusministerkonferenz or CCM) was established in 1948 by agreement between the States of the Federal Republic of Germany. Among its main responsibilities is to ensure quality and continuity of development in higher education. In Germany, the program of bachelors and masters must be accredited in accordance with Resolution Kultusministerkonerenz. In Ukraine Higher Education Accreditation carried out the Ministry of Education, Youth and Sports of Ukraine under four main levels. Ukraine's legislation on higher education based on the Constitution Ukraine consists of the laws of Ukraine ‘On osvititu’ ‘On scientific and technical activity’, ‘On Higher osvititu’ and other legal acts and is entirely within the competence of the state. This leads to considerable centralization and bureaucratization of the process. Thus, analysis of expertise shined can conclude that reforming the system of accreditation and quality of higher education in Ukraine to its integration into the global space requires solving a number of problems in the following areas: improving the system of state certification and licensing; optimizing the network of higher education institutions; creating both governmental and non-governmental organizations to monitor the process of higher education in Ukraine and so on.

Keywords: higher education, accreditation, decentralization, education institutions

Procedia PDF Downloads 323

Authors: Olga Maksakova

Abstract:

A work with unconscious patients after acute brain damages besides special knowledge and practical skills of all the participants requires a very specific organization. A lot of said about team approach in neurorehabilitation, usually as for outpatient mode. Rehabilitologists deal with fixed patient problems or deficits (motion, speech, cognitive or emotional disorder). Team-building means superficial paradigm of management psychology. Linear mode of teamwork fits casual relationships there. Cases with deep altered states of consciousness (vegetative states, coma, and confusion) require non-linear mode of teamwork: recovery of consciousness might not be the goal due to phenomenon uncertainty. Rehabilitation team as Semi-open Complex System includes the patient as a part. Patient's response pattern becomes formed not only with brain deficits but questions-stimuli, context, and inquiring person. Teamwork is sourcing of phenomenology knowledge of patient's processes as Third-person approach is replaced with Second- and after First-person approaches. Here is a chance for real-time change. Patient’s contacts with his own body and outward things create a basement for restoration of consciousness. The most important condition is systematic feedbacks to any minimal movement or vegetative signal of the patient. Up to now, recovery work with the most severe contingent is carried out in the mode of passive physical interventions, while an effective rehabilitation team should include specially trained psychologists and psychotherapists. It is they who are able to create a network of feedbacks with the patient and inter-professional ones building up the team. Characteristics of ‘Team-Patient’ system (TPS) are energy, entropy, and complexity. Impairment of consciousness as the absence of linear contact appears together with a loss of essential functions (low energy), vegetative-visceral fits (excessive energy and low order), motor agitation (excessive energy and excessive order), etc. Techniques of teamwork are different in these cases for resulting optimization of the system condition. Directed regulation of the system complexity is one of the recovery tools. Different signs of awareness appear as a result of system self-organization. Joint meetings are an important part of teamwork. Regular or event-related discussions form the language of inter-professional communication, as well as the patient's shared mental model. Analysis of complex communication process in TPS may be useful for creation of the general theory of consciousness.

Keywords: rehabilitation team, urgent rehabilitation, severe brain damage, consciousness disorders, complex system theory

Procedia PDF Downloads 130

Authors: Ishrat Zakia Sultana

Abstract:

The consistent persecution, ethnic cleansing, and genocide against the Rohingya in Burma resulted four major influxes of the Rohingya people to the neighboring country Bangladesh. After the latest influx of October 2016 and August 2017, the total number of Rohingya in Bangladesh stands somewhere between 900,000 to over one million, placing Bangladesh much ahead with the number of refugees compared to Dadaab and Kakuma in Kenya, Bidibidi in Uganda and Zaatari in Jordan. While Bangladesh received recognition and appreciation for receiving a huge number of the Rohingya, one of the fundamental human rights of the Rohingya – education – has never been fulfilled in Bangladesh. The Ministry of Disaster Management and Relief of the government of Bangladesh has been looking after the Rohingya and managing various programs for the Rohingya. On its website, the Ministry claims that it provides the basic supports/services to the Rohingya, including providing education. In practice, however, education for the Rohingya include only the provisions for registered Rohingya refugees – who are a very small number of populations among the entire Rohingya hosted in Bangladesh – and that is only up to grade 7 within the registered camps at Teknaf and Ukhia of Cox’s Bazar district of the country. There is no answer of the question, ‘What’s next’? Although refugees in Canada, Sudan, Turkey and other countries have been allowed to go to mainstream schools, Rohingya refugees in Bangladesh are not allowed to do so legally. Due to the lack of proof of nationality of the Rohingya, the government of Bangladesh imposes restrictions on their access to Bangladeshi schools. However, despite their vulnerability and statelessness, many Rohingyas are desperate to pursue education outside the camps and find their own way not only within Cox’s Bazar but also even in the capital city of the country. But they must hide their refugee identity to accomplish this. My research aims to explore how they manage to get admission amid government restrictions on their access to education in the mainstream institutions in Bangladesh. It will reveal how Rohingya people use adopted identity to get access to education in Bangladesh, and how they apply their own techniques to achieve their goals without having government approved identity. This research examined the strategies the Rohingya applied to manage documents related to their identity to ensure their admission to Bangladeshi education institutions – in schools, colleges, and universities. The research employed a qualitative approach. It used semi structured individual interviews and Focused Group Discussions (FGDs) with 20 male and female Rohingya refugees who are 18 years old and above, and have enrolled in Bangladeshi education institutions with adopted identity. Also I interviewed 5 local community members and policy makers to understand their perceptions and roles in this process. The findings of this research will allow the policy makers to rethink the outcomes of the restrictions on Rohingya’s education in Bangladesh, the ramifications of the denial of Rohingya’s access to education, and initiate policy dialogues on how to allow Rohingya refugees to pursue education in Bangladesh in legal way.

Keywords: Rohingya, Refugee, Bangladesh, Education

Procedia PDF Downloads 44