Search results for: body condition

Authors: M. S. Nandana, K. Udaya Bhat, C. M. Manjunatha

Abstract:

In this study aluminum alloy 7010 was subjected to three different ageing treatments i.e., peak ageing (T6), over-ageing (T7451) and retrogression and re ageing (RRA) to study the influence of precipitate microstructure on the fatigue crack growth rate behavior. The microstructural modification was studied by using transmission electron microscope (TEM) to examine the change in the size and morphology of precipitates in the matrix and on the grain boundaries. The standard compact tension (CT) specimens were fabricated and tested under constant amplitude fatigue crack growth tests to evaluate the influence of heat treatment on the fatigue crack growth rate properties. The tests were performed in a computer-controlled servo-hydraulic test machine applying a load ratio, R = 0.1 at a loading frequency of 10 Hz as per ASTM E647. The fatigue crack growth was measured by adopting compliance technique using a CMOD gauge attached to the CT specimen. The average size of the matrix precipitates were found to be of 16-20 nm in T7451, 5-6 nm in RRA and 2-3 nm in T6 conditions respectively. The grain boundary precipitate which was continuous in T6, was disintegrated in RRA and T7451 condition. The PFZ width was lower in RRA compared to T7451 condition. The crack growth rate was higher in T7451 and lowest in RRA treated alloy. The RRA treated alloy also exhibits an increase in threshold stress intensity factor range (∆Kₜₕ). The ∆Kₜₕ measured was 11.1, 10.3 and 5.7 MPam¹/² in RRA, T6 and T7451 alloys respectively. The fatigue crack growth rate in RRA treated alloy was nearly 2-3 times lower than that in T6 and was one order lower than that observed in T7451 condition. The surface roughness of RRA treated alloy was more pronounced when compared to the other conditions. The reduction in fatigue crack growth rate in RRA alloy was majorly due to the increase in roughness and partially due to increase in spacing between the matrix precipitates. The reduction in crack growth rate and increase in threshold stress intensity range is expected to benefit the damage tolerant capability of aircraft structural components under service loads.

Keywords: damage tolerance, fatigue, heat treatment, PFZ, RRA

Procedia PDF Downloads 153

Authors: Magdalena Jablonska, Andrzej Falkowski

Abstract:

The negativity effect is one of the most intriguing and well-studied psychological phenomena that can be observed in many areas of human life. The aim of the following study is to investigate how valence framing and positive and negative information about political candidates affect judgments about similarity to an ideal and bad politician. Based on the theoretical framework of features of similarity, it is hypothesized that negative features have a stronger effect on similarity judgments than positive features of comparable value. Furthermore, the mediating role of affect is tested. Method: One hundred sixty-one people took part in an experimental study. Participants were divided into 6 research conditions that differed in the reference point (positive vs negative framing) and the number of favourable and unfavourable information items about political candidates (a positive, neutral and negative candidate profile). In positive framing condition, the concept of an ideal politician was primed; in the negative condition, participants were to think about a bad politician. The effect of independent variables on similarity judgments, affective evaluation, and voting intention was tested. Results: In the positive condition, the analysis showed that the negative effect of additional unfavourable features was greater than the positive effect of additional favourable features in judgements about similarity to the ideal candidate. In negative framing condition, ANOVA was insignificant, showing that neither the addition of positive features nor additional negative information had a significant impact on the similarity to a bad political candidate. To explain this asymmetry, two mediational analyses were conducted that tested the mediating role of affect in the relationship between similarity judgments and voting intention. In both situations the mediating effect was significant, but the comparison of two models showed that the mediation was stronger for a negative framing. Discussion: The research supports the negativity effect and attempts to explain the psychological mechanism behind the positive-negative asymmetry. The results of mediation analyses point to a stronger mediating role of affect in the relationship between cognitive evaluation and voting intention. Such a result suggests that negative comparisons, leading to the activation of negative features, give rise to stronger emotions than positive features of comparable strength. The findings are in line with positive-negative asymmetry, however, by adopting Tversky’s framework of features of similarity, the study integrates the cognitive mechanism of the negativity effect delineated in the contrast model of similarity with its emotional component resulting from the asymmetrical effect of positive and negative emotions on decision-making.

Keywords: affect, framing, negativity effect, positive-negative asymmetry, similarity judgements

Procedia PDF Downloads 198

Authors: Karolina Ziembowicz, Andrzej Nowak

Abstract:

In the current study, we examined the consequences of adding prosodic cues to text communication by allowing users to observe the process of message creation while engaged in dyadic conversations. In the first condition, users interacted through a traditional chat that requires pressing ‘enter’ to make a message visible to an interlocutor. In another, text appeared on the screen simultaneously as the sender was writing it, letter after letter (Synchat condition), so that users could observe the varying rhythm of message production, precise timing of message appearance, typos and their corrections. The results show that the ability to observe the dynamics of message production had a twofold effect on the social interaction process. First, it enhanced the relational aspect of communication – interlocutors synchronized their emotional states during the interaction, their communication included more statements on relationship building, and they evaluated the Synchat medium as more personal and emotionally engaging. Second, it increased the coherence of communication, reflected in greater continuity of the topics raised in Synchat conversations. The results are discussed from the interaction design (IxD) perspective.

Keywords: chat communication, online conversation, prosody, social synchronization, interaction incoherence, relationship building

Procedia PDF Downloads 141

Authors: Amy Halseth, Kevin Shan, Kye Gilder, John Buse

Abstract:

The study assessed the effect of prolonged-release naltrexone 32 mg/bupropion 360 mg (NB) on cardiovascular (CV) events in overweight/obese participants at elevated CV risk. Participants must lose ≥ 2% body weight at 16 wks, without a sustained increase in blood pressure, to continue drug. The study was terminated early after second interim analysis with 50% of all CV events. Data on CV endpoints has been published. Current analyses focus on weight change. Intent-to-treat (ITT) population (placebo [PBO] N=4450, NB N=4455) was 54.5% female, 83.5% white, mean age 61 yrs, mean BMI 37.3 kg/m2; 85.2% had type 2 diabetes, 32.1% had CV disease, 17.4% had both. At 52 wks, ITT-LOCF analysis showed greater least squares mean percent change in weight (LSM%ΔBW) with NB (-3.1%; 95% CI -4.8, -1.4) vs PBO (-0.3%; 95% CI -1.9, 1.4). Both groups demonstrated greater weight loss while on-treatment (NB [-7.3%], PBO [-3.9%]). Odds ratios of 5% and 10% weight loss were 3.3 and 4.1 (ITT-LOCF), respectively, in NB over PBO. At 104 wks, on-treatment LSM%ΔBW was -6.3% with NB (n=1137) vs -3.5% with PBO (n=741). Major reasons for NB withdrawal were adverse events (AE, 29%) and patient decision (21%), with GI disorders being the most common. Weight loss with NB in this study, in an older population predominantly with diabetes and elevated CV risk, was somewhat lower than that observed in overweight/obese participants without diabetes and similar to participants with diabetes in Phase 3 studies.

Keywords: contrave, mysimba, obesity, pharmacotherapy, weight loss

Procedia PDF Downloads 319

Authors: Jason Dellatolla, Scott Thomas

Abstract:

Much of the current literature pertaining to resistance training (RT) volume prescription lacks ecological validity, and very few studies investigate true high-volume ranges. Purpose: The present study sought to investigate the effects of ecologically-valid high- vs low-volume RT on muscular size and strength in trained men. Methods: This study systematically randomized trained, college-aged men into two groups: low-volume (LV; n = 4) and high-volume (HV; n = 5). The sample size was affected by COVID-19 limitations. Subjects followed an ecologically-valid 6-week RT program targeting both muscle size and strength. RT occurred 3x/week on non-consecutive days. Over the course of six weeks, LVR and HVR gradually progressed from 15 to 23 sets/week and 30 to 46 sets/week of lower-body RT, respectively. Muscle strength was assessed via 3RM tests in the squat, stiff-leg deadlift (SL DL), and leg press. Muscle hypertrophy was evaluated through a combination of DXA, BodPod, and ultrasound (US) measurements. Results: Two-way repeated-measures ANOVAs indicated that strength in all 3 compound lifts increased significantly among both groups (p < 0.01); between-group differences only occurred in the squat (p = 0.02) and SL DL (p = 0.03), both of which favored HVR. Significant pre-to-post-study increases in indicators of hypertrophy were discovered for lean body mass in the legs via DXA, overall fat-free mass via BodPod, and US measures of muscle thickness (MT) for the rectus femoris, vastus intermedius, vastus medialis, vastus lateralis, long-head of the biceps femoris, and total MT. Between-group differences were only found for MT of the vastus medialis – favoring HVR. Moreover, each additional weekly set of lower-body RT was associated with an average increase in MT of 0.39% in the thigh muscles. Conclusion: We conclude that ecologically-valid RT regimens significantly improve muscular strength and indicators of hypertrophy. When HVR is compared to LVR, HVR provides significantly greater gains in muscular strength but has no greater effect on hypertrophy over the course of 6 weeks in trained, college-aged men.

Keywords: ecological validity, hypertrophy, resistance training, strength

Procedia PDF Downloads 114

Authors: Ghoul Rachid Brahim, Trad Khodja Rafik

Abstract:

Vertebral localization of the hydatid cyst is a severe form of bone hydatidosis, is a parasitic infection caused by the larval forms of the tapeworms Echinococcus granulosus, The disease is slowly remaining silent (a long incubation period) which may explain why this pathology is often discovered at the stage of neurological complications. The objective of this study is to recall the clinical and radiological aspects of this condition and the importance of early diagnosis and appropriate management. We report a study of 5 patients with vertebral hydatidosis, four men and one woman, four (04) patients operated in the emergency setting for spinal cord compression (decompression by wide laminectomy with evacuation of intra and extra canal vesicles).Albendazole-based medical treatment is instituted in all patients. Results: The evolution was favorable for three patients, the other two patients reoperated for a local recurrence. Conclusion: Vertebral hydatidosis is a rare condition with a poor prognosis due to the risk of neurological damage, the infiltrating nature of bone lesions, the frequency of relapses and therapeutic difficulties. The only curative method remains surgery, which must aim for complete and large excision of the lesions as if it were a “malignant tumour”.

Keywords: hydatidosis, Echinococcosis granulosus, hydatid cyst, spinal cord compression, laminectomy

Procedia PDF Downloads 97

Authors: Chen Zhang, Bernhard Schwarz-Röhr, Alexander Härting

Abstract:

To acquire accurate ship motions at the center of gravity, a single low-cost inertial sensor is utilized and applied on board to measure ship oscillating motions. As observations, the three axes accelerations and three axes rotational rates provided by the sensor are used. The mathematical model of processing the observation data includes determination of the distance vector between the sensor and the center of gravity in x, y, and z directions. After setting up the transfer matrix from sensor’s own coordinate system to the ship’s body frame, an extended Kalman filter is applied to deal with nonlinearities between the ship motion in the body frame and the observation information in the sensor’s frame. As a side effect, the method eliminates sensor noise and other unwanted errors. Results are not only roll and pitch, but also linear motions, in particular heave and surge at the center of gravity. For testing, we resort to measurements recorded on a small vessel in a well-defined sea state. With response amplitude operators computed numerically by a commercial software (Seaway), motion characteristics are estimated. These agree well with the measurements after processing with the suggested method.

Keywords: extended Kalman filter, nonlinear estimation, sea trial, ship motion estimation

Procedia PDF Downloads 522

Authors: Hamid Ahmadi, Neda Azari Dodaran

Abstract:

This paper aims to study the structural behavior of tubular KT-joints subjected to axial loading at fire induced elevated temperatures. At first, a finite element (FE) model was developed and validated against the data available from experimental tests. Then, a set of 810 FE analyses were performed to study the influence of temperature and dimensionless geometrical parameters (β, γ, θ, and τ) on the ultimate strength and initial stiffness. The joints were analyzed under two types of axial loading and five different temperatures (20 ºC, 200 ºC, 400 ºC, 550 ºC, and 700 ºC). Results show that the ultimate strength and initial stiffness of KT-joints decrease considerably by increasing the temperature. In the joints having bigger values of the β, the temperature elevation leads to less reduction in ultimate strength; while in the joints with bigger values of the γ, the temperature elevation results in more reduction in ultimate strength. The influence of the θ on the ultimate strength is independent from the temperature. To our knowledge, there is no design formula available for determining the ultimate strength of KT-joints at elevated temperatures. Hence, after parametric study, two equations were developed through nonlinear regression, for calculating the ultimate strength of KT-joints at elevated temperatures.

Keywords: axial loads, fire condition, parametric formula, static strength, tubular KT-joint

Procedia PDF Downloads 154

Authors: Aneri Mehta, Krunal Mehta

Abstract:

Financial administration is part of government which deals with collection, preservation and distribution of public funds, with the coordination of public revenue and expenditure, with the management of credit operation on behalf of the state and with the general control of the financial affairs of public households. The researcher has taken the prime body of the local self government viz. Municipal Corporation. However, the number of municipal corporations in India has rapidly increased in recent years. Countries 27% of the total population are living in urban area & in recent it increasing very fast. People are moving very fast from rural area to urban area. Their demand, awareness is increasing day by day. The Municipal Corporations render many services for the development of the urban area. Thus, researcher has taken a step to know the accounting practices of the municipal corporations of Gujarat state (AMC & BMC ). The research will try to show you the status of finance of municipal corporations. Article 243(w) of the constitution of India envisaged that the state government maybe, by law , endow the municipalities with such powers and authorities as may be necessary to enable them to function as institution of self government and such law may contain provision for devolution of powers and responsibilities upon municipalities subjects to such condition as may be specified there in with respect to (i) the peroration of plans for economic development and social justice and (ii) the performance of the function and the implementation of schemes as may be entrusted to them including those in relation to the matters listed in the twelfth schedule. The three tier structure of the Indian Government i.e. Union, State & Local Self Government is the scenario of the Indian constitution. Local Self Government performs or renders many services under the direct control of state government. They (local bodies) possess autonomy within its limited sphere, raise revenue through local taxation and spend its income on local services.

Keywords: financial administration, urban local bodies, local self government, constitution

Procedia PDF Downloads 465

Authors: Arosha Rashmi De Silva, Ananda Chandrasekara

Abstract:

This study seeks to comprehensively examine the influence of fast-food consumption and physical activity levels on the body weight of young employees within the private sector of Sri Lanka. The escalating popularity of fast food has raised concerns about its nutritional content and associated health ramifications. To investigate this phenomenon, a cohort of 100 individuals aged between 25 and 45, employed in Sri Lanka's private sector, participated in this research. These participants provided socio-demographic data through a standardized questionnaire, enabling the characterization of their backgrounds. Additionally, participants disclosed their frequency of fast-food consumption and engagement in physical activities, utilizing validated assessment tools. The collected data was meticulously compiled into an Excel spreadsheet and subjected to rigorous statistical analysis. Descriptive statistics, such as percentages and proportions, were employed to delineate the body weight status of the participants. Employing chi-square tests, our study identified significant associations between fast-food consumption, levels of physical activity, and body weight categories. Furthermore, through binary logistic regression analysis, potential risk factors contributing to overweight and obesity within the young employee cohort were elucidated. Our findings revealed a disconcerting trend, with 6% of participants classified as underweight, 32% within the normal weight range, and a substantial 62% categorized as overweight or obese. These outcomes underscore the alarming prevalence of overweight and obesity among young private-sector employees, particularly within the bustling urban landscape of Colombo, Sri Lanka. The data strongly imply a robust correlation between fast-food consumption, sedentary behaviors, and higher body weight categories, reflective of the evolving lifestyle patterns associated with the nation's economic growth. This study emphasizes the urgent need for effective interventions to counter the detrimental effects of fast-food consumption. The implementation of awareness campaigns elucidating the adverse health consequences of fast food, coupled with comprehensive nutritional education, can empower individuals to make informed dietary choices. Workplace interventions, including the provision of healthier meal alternatives and the facilitation of physical activity opportunities, are essential in fostering a healthier workforce and mitigating the escalating burden of overweight and obesity in Sri Lanka

Keywords: fast food consumption, obese, overweight, physical activity level

Procedia PDF Downloads 50

Authors: Mandar Ghodekar, Sharad Jadhav, Sangram Jadhav

Abstract:

Speed control of rotor during startup and under varying load conditions is one of the most difficult tasks of gas turbine operation. In this paper, power plant gas turbine (GE9001E) is considered for this purpose and fuzzy and fuzzy-PI rotor speed controllers are designed. The goal of the presented controllers is to keep the turbine rotor speed within predefined limits during startup condition as well as during operating condition. The fuzzy controller and fuzzy-PI controller are designed using Takagi-Sugeno method and Mamdani method, respectively. In applying the fuzzy-PI control to a gas-turbine plant, the tuning parameters (Kp and Ki) are modified online by fuzzy logic approach. Error and rate of change of error are inputs and change in fuel flow is output for both the controllers. Hence, rotor speed of gas turbine is controlled by modifying the fuel ƒflow. The identified linear ARX model of gas turbine is considered while designing the controllers. For simulations, demand power is taken as disturbance input. It is assumed that inlet guide vane (IGV) position is fixed. In addition, the constraint on the fuel flow is taken into account. The performance of the presented controllers is compared with each other as well as with H∞ robust and MPC controllers for the same operating conditions in simulations.

Keywords: gas turbine, fuzzy controller, fuzzy PI controller, power plant

Procedia PDF Downloads 334

Authors: C. A. Sharma, Birendra P. Singh

Abstract:

Ichnofacies analysis is considered the best paleontological tool for interpreting ancient depositional environments. Nineteen (19) ichnogenera (namely: Bergaueria, Catenichnus, Cochlichnus, Cruziana, Diplichnites, Dimorphichnus, Diplocraterion, Gordia, Guanshanichnus, Lockeia, Merostomichnites, Monomorphichnus, Palaeophycus, Phycodes, Planolites, Psammichnites, Rusophycus, Skolithos and Treptichnus) are recocered from the Tal Group (Cambrian) of the Nigalidhar Syncline. The stratigraphic occurrences of these ichnogenera represent alternating proximal Cruziana and Skolithos ichnofacies along the contact of Sankholi and Koti-Dhaman formations of the Tal Group. Five ichnogenera namely Catenichnus, Guanshanichnus, Lockeia, Merostomichnites and Psammichnites are recorded for the first time from the Nigalidhar Syncline. Cruziana ichnofacies is found in the upper part of the Sankholi Formation to the lower part of the Koti Dhaman Formation in the NigaliDhar Syncline. The preservational characters here indicate a subtidal environmental condition with poorly sorted, unconsolidated substrate. Depositional condition ranging from moderate to high energy levels below the fair weather base but above the storm wave base under nearshore to foreshore setting in a wave dominated shallow water environment is also indicated. The proximal Cruziana-ichnofacies is interrupted by the Skolithos ichnofacies in the Tal Group of the Nigalidhar Syncline which indicate fluctuating high energy condition which was unfavorable for the opportunistic organism which were dominant during the proximal Cruziana ichnofacies. The excursion of Skolithos ichnofacies (as a pipe rock in the upper part of Sankholi Formation) into the proximal Cruziana ichnofacies in the Tal Group indicate that increased energy and allied parameters attributed to the high rate of sedimentation near the proximal part of the basin. The level bearing the Skolithos ichnofacies in the Nigalidhar Syncline at the juncture of Sankholi and Koti-Dhaman formations can be correlated to the level marked as unconformity in between the Deo-Ka-Tibba and the Dhaulagiri formations by the conglomeratic horizon in the Mussoorie Syncline, Lesser Himalaya, India. Thus, the Tal Group of the Nigalidhar syncline at this stratigraphic level represent slightly deeper water condition than the Mussoorie Syncline, where in the later the aerial exposure dominated which leads to the deposition of conglomeratic horizon and subsequent formation of unconformity. The overall ichnological and sedimentological dataset allow us to infer that the Cambrian successions of Nigalidhar Syncline were deposited in a wave-dominated proximal part of the basin under the foreshore to close to upper shoreface regimes of the shallow marine setting.

Keywords: Cambrian, Ichnofacies, Lesser Himalaya, Nigalidhar, Tal Group

Procedia PDF Downloads 258

Authors: Luisa Villani

Abstract:

The proposal aims to express concerns about the connection between mind, body, society, and environment in the Flyers’ dance, a very well-known rotatory dance in Mexico, to create meanings and to make the apprehension of the world possible. The interaction among the brain, mind, body, and environment, and the intersubjective relation among them, means the world creates and recreates a social interaction. The purpose of this methodology, based on the embodied cognition theory, which was named “A Performance-Embodied Theory” is to find the principles and patterns that organize the culture and the rules of the apprehension of the environment by Totonac people while the dance is being performed. The analysis started by questioning how anthropologists can interpret how Totonacs transform their unconscious knowledge into conscious knowledge and how the scheme formation of imagination and their collective imagery is understood in the context of public-facing rituals, such as Flyers’ dance. The problem is that most of the time, researchers interpret elements in a separate way and not as a complex ritual dancing whole, which is the original contribution of this study. This theory, which accepts the fact that people are body-mind agents, wants to interpret the dance as a whole, where the different elements are joined to an integral interpretation. To understand incorporation, data was recollected in prolonged periods of fieldwork, with participant observation and linguistic and extralinguistic data analysis. Laban’s notation for the description and analysis of gestures and movements in the space was first used, but it was later transformed and gone beyond this method, which is still a linear and compositional one. Performance in a ritual is the actualization of a potential complex of meanings or cognitive domains among many others in a culture: one potential dimension becomes probable and then real because of the activation of specific meanings in a context. It can only be thought what language permits thinking, and the lexicon that is used depends on the individual culture. Only some parts of this knowledge can be activated at once, and these parts of knowledge are connected. Only in this way, the world can be understood. It can be recognized that as languages geometrize the physical world thanks to the body, also ritual does. In conclusion, the ritual behaves as an embodied grammar or a text in movement, which, depending on the ritual phases and the words and sentences pronounced in the ritual, activates bits of encyclopedic knowledge that people have about the world. Gestures are not given by the performer but emerge from the intentional perception in which gestures are “understood” by the audio-spectator in an inter-corporeal way. The impact of this study regards the possibility not only to disseminate knowledge effectively but also to generate a balance between different parts of the world where knowledge is shared, rather than being received by academic institutions alone. This knowledge can be exchanged, so indigenous communities and academies could be together as part of the activation and the sharing of this knowledge with the world.

Keywords: dance, flyers, performance, embodied, cognition

Procedia PDF Downloads 58

Authors: Mohammad Reza Shahnazari, Reza Kazemi, Ali Saberi

Abstract:

Most of the engineering problems are in nonlinear forms. Nonlinear boundary layer problems defined in infinite intervals contain specific complexities, especially in boundary layer condition conformance. As an example of these nonlinear complex problems, the well-known Blasius equation can be mentioned, which itself is one of the classic boundary layer problems. No analytical solution has been proposed yet for the Blasius equation due to its complexity. In this paper, an analytical method, namely the Kourosh method, based on the singularity perturbation method and the Liao homotopy analysis is utilized to solve the Blasius problem. In this method, an inner solution is developed in the [0,1] interval to expedite the solution convergence. The magnitude of the f ˝(0), as an essential quantity for determining the physical parameters, is directly calculated from the solution of the boundary condition problem. The advantages of this solution are that it does not need any numerical solution, it has a closed form and that its validation is shown in the entire [0,∞] interval. Furthermore, all of the desirable parameters could be extracted through a series of simple analytical operations from the final solution. This solution also satisfies the continuity conditions, which is one of the main contributions of this paper in comparison with most of the other proposed analytical solutions available in the literature. Comparison with numerical solutions reveals that the proposed method is highly accurate and convenient for application.

Keywords: Blasius equation, boundary layer, Kourosh method, analytical solution

Procedia PDF Downloads 391

Authors: Ozioma Beauty Nwaodu, Adebowale E Salako, Omolara Mabel Akinyemi, Nkechi Uche, Isuama Isu, Uchechi Jane Elechi

Abstract:

Goats form an integral part of livestock production in the tropics. Meat potential is determined subjectively by resource poor livestock keepers, using hand to measure the rump width (RW). Objective evaluation of meat potential in different breads of goats can overcome problems associated with subjective evaluation. Hence, the objectives were to predict meatiness in Red Sokoto (RS), Sahel and the West African Dwarf (WAD) goats, using product of the body length (BL), wither height (WH) and (RW) and to indicate the inherent size of each breed, using WH: BL ratio. These three parameters were used because they are less environmentally sensitive. A total of 2849 goats were sampled purposefully from the Akinyele and Oranyan markets in Ibadan, Oyo State Nigeria. RS showed no significant difference for BL and WH but different from the RW of both sexes (p < 0.01). Similarly WAD showed no significant difference for the BL and WH, but differed (p < 0.01) between sexes for RW. Using the ANOVA, BL:WH ratio showed no significant difference between the breeds. WAD goats have the highest mean for BL:WH ratio. Western meat livestock is primarily identified using BL:WH. The combinations of these body parameters as indicator for meat type in meat animals showed that WAD goat has more potential to lay down meat, than RS and Sahel.

Keywords: quantitative, morphologial traits, descriptive analysis, goats

Procedia PDF Downloads 185

Authors: Sae-Yeon Seong, EunSun Chung, Dongjoo Chin

Abstract:

Conflict of interest (COI) is one of the dominant circumstantial factors of moral corruption across various fields. Several management strategies have been proposed to prevent self-interested decision making in COIs. Among these strategies, message persuasion has been considered as a practical and effective approach. Framing and repetition are two of the major factors in the persuasion effect of message. Therefore, their effect on moral decision making in COI should be explored systematically. The purpose of this study was to compare the differential effects of positively framed message and negatively framed message, and secondly, to investigate how the effectiveness of persuasive message changes through repetitive exposures. A total of 63 participants were randomly assigned to one of 3 framing conditions: positive framing, negative framing, and no-message condition. Prior to the online experiment involving a consultation task, the differently framed persuasive message was presented to the participants. This process was repeated four times in a row. The results showed that participants with positive-framing message were less likely to provide self-interested consultation than participants in the no-message condition. Also, a U-shaped quadric relation between repetition and self-interest consultation was found. Implications and limitations are further discussed.

Keywords: conflicts of interest, persuasive message, framing effect, repetition effect, self-interested behavior

Procedia PDF Downloads 176

Authors: Bahiru Tsegaye, Chandrajit Balomajumder, Partha Roy

Abstract:

The limited supply and related negative environmental consequence of fossil fuels are driving researcher for finding sustainable sources of energy. Lignocellulose biomass like sorghum straw is considered as among cheap, renewable and abundantly available sources of energy. However, lignocellulose biomass conversion to bioenergy like bioethanol is hindered due to the reluctant nature of lignin in the biomass. Therefore, removal of lignin is a vital step for lignocellulose conversion to renewable energy. The aim of this study is to optimize microwave pretreatment conditions using design expert software to remove lignin and to release maximum possible polysaccharides from sorghum straw for efficient hydrolysis and fermentation process. Sodium hydroxide concentration between 0.5-1.5%, v/v, pretreatment time from 5-25 minutes and pretreatment temperature from 120-2000C were considered to depolymerize sorghum straw. The effect of pretreatment was studied by analyzing the compositional changes before and after pretreatments following renewable energy laboratory procedure. Analysis of variance (ANOVA) was used to test the significance of the model used for optimization. About 32.8%-48.27% of hemicellulose solubilization, 53% -82.62% of cellulose release, and 49.25% to 78.29% lignin solubilization were observed during microwave pretreatment. Pretreatment for 10 minutes with alkali concentration of 1.5% and temperature of 1400C released maximum cellulose and lignin. At this optimal condition, maximum of 82.62% of cellulose release and 78.29% of lignin removal was achieved. Sorghum straw at optimal pretreatment condition was subjected to enzymatic hydrolysis and fermentation. The efficiency of hydrolysis was measured by analyzing reducing sugars by 3, 5 dinitrisylicylic acid method. Reducing sugars of about 619 mg/g of sorghum straw were obtained after enzymatic hydrolysis. This study showed a significant amount of lignin removal and cellulose release at optimal condition. This enhances the yield of reducing sugars as well as ethanol yield. The study demonstrates the potential of microwave pretreatments for enhancing bioethanol yield from sorghum straw.

Keywords: cellulose, hydrolysis, lignocellulose, optimization

Procedia PDF Downloads 271

Authors: B. R. Jana, Madhumita Singh

Abstract:

Storage study of bael fruit and pulp were conducted at ICAR-RCER, Research Centre Ranchi to find out suitable storage life to extent the availability of the fruit and produce the value added product in form of fruit. The cultivar under storage is Pant Sujata. CFB box packing resulted in minimum 21 % PLW during 2010-11 during its 28-35 days storage under ambient temperature. CFB box and Gunny bag retains maximum total sugar (17.3-17.4 °B) after 28 days storage. Bael pulp of cultivar Pant Sujata can be stored up to 2 months at 4 °C with good quality condition. Treatments were highly significant in the characters such as T.S.S., acidity, reducing sugar and total sugar. Storage conditions and treatments interaction were insignificant in all characters except acidity. The maximum T.S.S. of 21.87 °B has been found in sample treated with 800 ppm benzoic acid when kept for two months at 4 °C temperature. This treatment also resulted in retaining the maximum reducing sugar (8.09 %) and total sugar content (9.52 %) at same storage condition than other treatments. From the present experiments, it is concluded that CFB box packing and pulp storage with 800 ppm benzoic acid at 4 °C are important to extent the availability of bael for two months.

Keywords: bael, storage, fruits, pulp, benzoic acid

Procedia PDF Downloads 247

Authors: Ava Zarif Sanayei, Sedigheh Sina

Abstract:

Interventional radiology (IR) uses imaging guidance, including X-rays and CT scans, to deliver therapy precisely. Most IR procedures are performed under local anesthesia and start with a small needle being inserted through the skin, which may be called pinhole surgery or image-guided surgery. There is increasing concern about radiation exposure during interventional radiology procedures due to procedure complexity. The basic aim of optimizing radiation protection as outlined in ICRP 139, is to strike a balance between image quality and radiation dose while maximizing benefits, ensuring that diagnostic interpretation is satisfactory. This study aims to estimate the equivalent doses to the main trunk of the body for the Interventional radiologist and Superintendent using LiF: Mg, Ti (TLD-100) chips at the IR department of a hospital in Shiraz, Iran. In the initial stage, the dosimeters were calibrated with the use of various phantoms. Afterward, a group of dosimeters was prepared, following which they were used for three months. To measure the personal equivalent dose to the body, three TLD chips were put in a tissue-equivalent batch and used under a protective lead apron. After the completion of the duration, TLDs were read out by a TLD reader. The results revealed that these individuals received equivalent doses of 387.39 and 145.11 µSv, respectively. The findings of this investigation revealed that the total radiation exposure to the staff was less than the annual limit of occupational exposure. However, it's imperative to implement appropriate radiation protection measures. Although the dose received by the interventional radiologist is a bit noticeable, it may be due to the reason for using conventional equipment with over-couch x-ray tubes for interventional procedures. It is therefore important to use dedicated equipment and protective means such as glasses and screens whenever compatible with the intervention when they are available or have them fitted to equipment if they are not present. Based on the results, the placement of staff in an appropriate location led to increasing the dose to the radiologist. Manufacturing and installation of moveable lead curtains with a thickness of 0.25 millimeters can effectively minimize the radiation dose to the body. Providing adequate training on radiation safety principles, particularly for technologists, can be an optimal approach to further decreasing exposure.

Keywords: interventional radiology, personal monitoring, radiation protection, thermoluminescence dosimetry

Procedia PDF Downloads 62

Authors: Amir Rashid

Abstract:

Cloud Computing frameworks empower organizations to cut expenses by outsourcing computation resources on-request. As of now, customers of Cloud service providers have no methods for confirming the privacy and ownership of their information and data. To address this issue we propose the platform of a trusted cloud computing program (TCCP). TCCP empowers Infrastructure as a Service (IaaS) suppliers, for example, Amazon EC2 to give a shout box execution condition that ensures secret execution of visitor virtual machines. Also, it permits clients to bear witness to the IaaS supplier and decide if the administration is secure before they dispatch their virtual machines. This paper proposes a Trusted Cloud Computing Platform (TCCP) for guaranteeing the privacy and trustworthiness of computed data that are outsourced to IaaS service providers. The TCCP gives the deliberation of a shut box execution condition for a client's VM, ensuring that no cloud supplier's authorized manager can examine or mess up with its data. Furthermore, before launching the VM, the TCCP permits a client to dependably and remotely acknowledge that the provider at backend is running a confided in TCCP. This capacity extends the verification of whole administration, and hence permits a client to confirm the data operation in secure mode.

Keywords: cloud security, IaaS, cloud data privacy and integrity, hybrid cloud

Procedia PDF Downloads 299

Authors: T. Z. Butt, T. A. Tabish, K. Anjum, H. Hafeez

Abstract:

A study of martensitic stainless steel surgical grade AISI 420A produced in Japan was carried out in this research work. The sample was already annealed at about 898˚C. The sample were subjected to chemical analysis, hardness, tensile and metallographic tests. These tests were performed on as received annealed and heat treated samples. In the annealed condition the sample showed 0HRC. However, on tensile testing, in annealed condition the sample showed maximum elongation. The heat treatment is carried out in vacuum furnace within temperature range 980-1035°C. The quenching of samples was carried out using liquid nitrogen. After hardening, the samples were subjected to tempering, which was carried out in vacuum tempering furnace at a temperature of 220˚C. The hardened samples were subjected to hardness and tensile testing. In hardness testing, the samples showed maximum hardness values. In tensile testing the sample showed minimum elongation. The sample in annealed state showed coarse plates of martensite structure. Therefore, the studied steels can be used as biomaterials.

Keywords: biomaterials, martensitic steel, microsrtucture, tensile testing, hardening, tempering, bioinstrumentation

Procedia PDF Downloads 277

Authors: Sohaib Raza, Parvez Mantry

Abstract:

Frailty is a multi-system impairment associated with stressors such as age, disease, and invasive surgical procedures. This multi-system impairment can lead to increased post-transplant mortality and functional decline. Additionally, the prevalence and/or severity of frailty increases when patient pre-habilitation is unsatisfactory or lacking. We conducted a retrospective study to examine whether the COVID-19 Pandemic, and subsequent lack of patient access to pre-habilitation and physical therapy resources, led to an increase in the prevalence and severity of frailty, sarcopenia, and other comorbidities including diabetes, hypertension, and COPD. Secondarily, we examined the correlation between patient survival rate and liver frailty index as well as muscle wasting/sarcopenia. Data were analyzed in order to correlate variables associated with these parameters. Three hundred sixty-nine liver transplant candidates at Methodist Dallas Medical Center were administered pre-transplant frailty assessments, which consisted of chair stands, grip strength, and position balance time. A frailty score less than 3.2 indicated a robust condition, a score from 3.3 to 4.4 indicated a pre-frail condition, and a score greater than 4.5 indicated a frail condition. Greater than 50 percent of patients were found to have muscle wasting in the COVID-19 period (March 13, 2020 to February 28, 2022), an increase of 16.5 percent from the pre-COVID period (April 1st, 2018 to March 12, 2020). Additionally, sarcopenia was associated with a two-fold increase in patient mortality rate. Furthermore, high liver frailty index scores were associated with increased patient mortality. However, there was no significant difference in liver frailty index or number of comorbidities between patients in the two cohorts. Conclusion: The COVID-19 Pandemic exacerbated sarcopenia-related muscle wasting in liver transplant candidates, and patient survival rate was directly correlated with liver frailty index score and the presence of sarcopenia.

Keywords: frailty, sarcopenia, covid-19, patient mortality, pre-habilitation, liver transplant candidates

Procedia PDF Downloads 117

Authors: John Olayinka Atoyebi

Abstract:

Developing countries like Nigeria are facing myriad problems, ranging from economic challenges, lack of no jobs, food insecurity, malnutrition, and poverty. However, tackling some of these menaces is not just a trivial issue neither do some of them require rocket science to fix, but rather the understanding of every individual citizen recognizing their respective roles that they have to play in making the country better, rather than putting all the blames on the Government. Tackling nutrition and food insecurity is a complex problem, but this work examines what an individual can do to improve nutrient consumption. Leafy indigenous vegetables can be termed as functional foods since they are very rich in nutrients, phytochemicals and other beneficial compounds to the body system. These functional foods are the class that provides necessary health benefits beyond basic nutrition. Usually functional foods often contain bioactive compounds, which help the body through the prevention and management of various diseases, as well as improving the overall health of human beings. The analysis carried out on some Nigerian leafy indigenous vegetables in home grown setting revealed, for example, the potential use of Iron (Fe) amount of 318.15ppm in Basella alba (red species) and that of Telfaria Occidentalis (Ugu) with 261.22ppm as being useful to stimulate heme, a necessary precursor and protein in the formation of blood in human being. Moreso, Virnonia amygdalina (ewuro) and water leaf possess anti-bacterial and anti-diabetic properties. They also provide digestive health benefits and support to the body system, including anti-inflammatory properties. Also, medicinal plant like Morinda citrifolia (Noni), which had been found to possess anti-cancer properties, has a Vitamin C amount of 528.85 mg/100g and a total carotenoids amount of 85.50 µg/g. However, despite all these results and potential utilization of these and other indigenous vegetables in Nigeria, there is a gross unawareness and/or non-cognizance of their utilization potentials, as some home garden lacks understanding of the immense nutrition benefits, thus hindering some of the populace to make proper use of these vegetables to enhance their health.

Keywords: developing countries, optimising, leafy vegetables, functional foods

Procedia PDF Downloads 5

Authors: Y. A. Shettima, M. A. Tijjani, S. Modu, F. I. Abdulrahman, B. M. Abubakar

Abstract:

The toxicity profile of the methanolic extract of Punica granatum L. fruit rind was studied in normal rats. The rats were administered orally by intubating graded doses of 150, 250, 500 and 750 mg/kg body weight of the extract for 28 days and the effects on biochemical parameters and histology of the liver and kidney were evaluated. There was a significant increase (P<0.05) in the levels of liver enzymes of the rats that received the highest dose of 750 mg/kg body weight. The AST and ALT levels were 41.59±0.18 ALP and 9.25±0.29 IU/L, respectively, while the ALP level was 15.68±10 IU/L.There was a significant difference in the albumin and globulin levels; 3.72±0.05 and 4.05±0.13 g/dl, respectively. Serum urea and creatinine levels remained normal, as well as the electrolyte levels. The increase in sodium concentration observed was not statistically significant (P≥0.05) when the control group (131.50±3.11) was compared with the experimental groups (132.25±3.86, 132.75±3.86, 133.50±3.11 and 134.00±1.83). The increase in potassium concentration was not statistically significant (P≥0.05) when the control group with a value of 95.50±3.51 mmol/L was compared with the experimental groups 98.00±3.16, 99.25±2.22, 99.79±0.36 and 99.99±0.02 mmol/L. The increase observed in bicarbonate concentration was not statistically significant (P≥0.05) when the control group with a value of 20.75±1.71 mmol/L was compared with the experimental groups 21.68±0.62, 24.25±2.99, 24.50±3.42, 25.50±2.65 mmol/L.

Keywords: punical granatum, methanolic, ALT, AST, electrolytes, histology

Procedia PDF Downloads 397

Authors: Srinivasan Chandrasekaran, Shihas A. Khader

Abstract:

Motion response of floating structures is of great concern in marine engineering. Nonlinearity is an inherent property of any floating bodies subjected to irregular waves. These floating structures are continuously subjected to environmental loadings from wave, current, wind etc. This can result in undesirable motions of the vessel which may challenge the operability. For a floating body to remain in its position, it should be able to induce a restoring force when displaced. Mooring is provided to enable this restoring force. This paper discuss the hydrodynamic performance and motion characteristics of an 8 point spread mooring system applied to a pipe laying barge operating in the West African sea. The modelling of the barge is done using a computer aided-design (CAD) software RHINOCEROS. Irregular waves are generated using a suitable wave spectrum. Both frequency domain and time domain analysis is done. Numerical simulations based on potential theory are carried out to find the responses and hydrodynamic performance of the barge in both free floating as well as moored conditions. Initially, potential flow frequency domain analysis is done to obtain the Response Amplitude Operator (RAO) which gives an idea about the structural motion in free floating state. RAOs for different wave headings are analyzed. In the following step, a time domain analysis is carried out to obtain the responses of the structure in the moored condition. In this study, wave induced motions are only taken into consideration. Wind and current loads are ruled out and shall be included in future studies. For the current study, 5000 seconds simulation is taken. The results represent wave-induced motion responses, mooring line tensions and identifies critical mooring lines.

Keywords: irregular wave, moored barge, time domain analysis, numerical simulation

Procedia PDF Downloads 252

Authors: S. Techaoei, K. Jarmkom, P. Eakwaropas, W. Khobjai

Abstract:

The objective of this research was focused on investigating in vitro antimicrobial activity of Phellinus linteus fruiting body extracts on Pseudomonas aeruginosa, Escherichia coli, Staphylococcus aureus and Methicillin-resistant Staphylococcus aureus. Phellinus linteus fruiting body was extracted with ethanol and ethyl acetate and was vaporized. The disc diffusion assay was used to assess antimicrobial activity against tested bacterial strains. Primary screening of chemical profile of crude extract was determined by using thin layer chromatography. The positive control and the negative control were used as erythromycin and dimethyl sulfoxide, respectively. Initial screening of Phellinus linteus crude extract with the disc diffusion assay demonstrated that only ethanol had greater antimicrobial activity against Pseudomonas aeruginosa, Escherichia coli, Staphylococcus aureus and Methicillin-resistant Staphylococcus aureus. The MIC assay showed that the lower MIC was observed with 0.5 mg/ml of Pseudomonas aeruginosa and Methicillin-resistant Staphylococcus aureus and 0.25 mg/ml. of Escherichia coli and Staphylococcus aureus, respectively. TLC chemical profile of extract was represented at R_f ≈ 0.71-0.76.

Keywords: Staphylococcus aureus, Escherichia coli, Phellinus linteus, Methicillin-resistant Staphylococcus aureus, antimicrobial activity

Procedia PDF Downloads 284

Authors: Farzad Shidfar, Najmeh Rostami, Ziaodin Mazhari, Fatemeh Hosseini Baharanchi

Abstract:

Background and Aim: The rate of failure to maintain a reduced weight has been increased. By definition, people who regain about one-third to two-thirds of their lost weight after one year from the end of the dietary treatment and return all the lost weight after 5 years it is called weight regain. This study was performed to find the causes of weight regain and its relationship with biochemical and psychological factors. Materials and Methods: This cross-sectional study was performed by reviewing the files of people who followed the dietary treatment in 1397-1398.seventy-three persons was in the weight regain group, and seventy-three people were in the weight maintenance group. Psychological factors such as depression, anxiety, quality of life, physical activity, and dietary frequency were assessed through a questionnaire, and biochemical factors such as serum insulin and fasting blood sugar were measured. The mean basal energy in the weight regain group was significantly higher than the weight maintenance group (p = 0.004). There was no significant difference between the two groups in terms of food intake and inflammatory index of food. There was no significant difference between the two groups in terms of food intake and inflammatory index of food. Mean serum insulin concentration (p = 0.023), mean fasting blood sugar (p = 0.04) and insulin resistance (p = 0.013) in the weight regain group were higher than the weight maintenance group. The weight maintenance group showed higher insulin sensitivity than the weight regain group (p = 0.005). There was no significant difference between the two groups in terms of psychological indicators. Conclusion: The only body mass index after one year from the end of the treatment period, insulin sensitivity, serum insulin concentration, fasting blood sugar, insulin resistance, selenium intake, and basal energy expenditure Specific and significant with weight regain. However, the significance of insulin resistance, basal energy expenditure, and body mass index after one year from the end of the treatment period was higher than other variables in the weight regain group.

Keywords: body weight maintenance, weight regain, insulin resistance, insulin sensitivity

Procedia PDF Downloads 114

Authors: Mohamed Amin Mekheimer

Abstract:

This study aimed to investigate the effects of paper-based monolingual, pop-up and type-in electronic dictionaries on improving reading comprehension and incidental vocabulary acquisition and retention in an EFL context. It tapped into how computer-mediated dictionaries may have facilitated/impeded reading comprehension and vocabulary acquisition. Findings showed differential effects produced by the three treatments compared with the control group. Specifically, it revealed that the pop-up dictionary condition had the shortest average vocabulary searching time, vocabulary and text reading time, yet with less than the type-in dictionary group but more than the book dictionary group in terms of frequent dictionary 'look-ups' (p<.0001). In addition, ANOVA analyses also showed that text reading time differed significantly across all four treatments, and so did reading comprehension. Vocabulary acquisition was reported as enhanced in the three treatments rather than in the control group, but still with insignificant differences across the three treatments, yet with more differential effects in favour of the pop-up condition. Data also assert that participants preferred the pop-up e-dictionary more than the type-in and paper-based groups. Explanations of the findings vis-à-vis the cognitive load theory were presented. Pedagogical implications and suggestions for further research were forwarded at the end.

Keywords: computer-mediated dictionaries, type-in dictionaries, pop-up dictionaries, reading comprehension, vocabulary acquisition

Procedia PDF Downloads 435

Authors: Toufik Bensana, Medkour Mihoub, Slimane Mekhilef

Abstract:

The use of vibration analysis has been established as the most common and reliable method of analysis in the field of condition monitoring and diagnostics of rotating machinery. Rolling bearings cover a broad range of rotary machines and plays a crucial role in the modern manufacturing industry. Unfortunately, the vibration signals collected from a faulty bearing are generally nonstationary, nonlinear and with strong noise interference, so it is essential to obtain the fault features correctly. In this paper, a novel numerical analysis method based on local mean decomposition (LMD) is proposed. LMD decompose the signal into a series of product functions (PFs), each of which is the product of an envelope signal and a purely frequency modulated FM signal. The envelope of a PF is the instantaneous amplitude (IA), and the derivative of the unwrapped phase of a purely flat frequency demodulated (FM) signal is the IF. After that, the fault characteristic frequency of the roller bearing can be extracted by performing spectrum analysis to the instantaneous amplitude of PF component containing dominant fault information. The results show the effectiveness of the proposed technique in fault detection and diagnosis of rolling element bearing.

Keywords: fault diagnosis, rolling element bearing, local mean decomposition, condition monitoring

Procedia PDF Downloads 389

Authors: M. Safiqul Islam, Md Arafat Hossain Sarkar

Abstract:

Brachytherapy is one of the most important cancer treatment management systems in radiotherapy department. Brachytherapy treatment is moved into High Dose Rate (HDR) after loader from Low Dose Rate (LDR) after loader due to radiation protection advantage. HDR Brachytherapy is a highly multipurpose system for enhancing cure and achieving palliation in many common cancers disease of developing countries. High-dose rate (HDR) Brachytherapy is a type of internal radiation therapy that delivers radiation from implants placed close to or inside, the tumor(s) in the body. This procedure is very effective at providing localized radiation to the tumor site while minimizing the patient’s whole body dose. Brachytherapy has proven to be a highly successful treatment for cancers of the prostate, cervix, endometrium, breast, skin, bronchus, esophagus, and head and neck, as well as soft tissue sarcomas and several other types of cancer. For the time being in our country we have 10 new HDR Remote after loading Brachytherapy. Right now 4 HDR Brachytherapy is already installed and running for patient’s treatment out of 10 HDR Brachytherapy. Ir-192 source is more comfortable than Co-60. In that case people or expert personnel prefer Ir-192 source for different kind of cancer patients. Ir-192 are economically, more flexible and familiar in our country.

Keywords: Ir-192, brachytherapy, cancer treatment, prostate, cervix, endometrium, breast, skin, bronchus, esophagus, soft tissue sarcomas

Procedia PDF Downloads 431