Search results for: residue number system

Authors: Ali Fuad Ashour

Abstract:

Introduction: Multiple sclerosis (MS) is a chronic, progressive and degenerative disease that affects the central nervous system (CNS). MS has been described to result in the debilitating symptom of the disease. It is reported to have a negative impact on the patient’s mental activities, brings a lower quality of life, leads to unemployment, causes distress and psychological disorders, generates low levels of motivation and self-esteem, and result in disability and neurological impairment. The aim of this study was to compare the effects of MS on patients from Britain and Kuwait. Methodology: A questionnaire was distributed to 200 individuals with MS (100 Kuwaiti and 100 British). The questionnaire consists of three parts; 1. General demographics, 2. Disease-specific data (symptoms, severity levels, relapse frequency, and support system), and 3. Attitudes towards physical exercise. Results: A response rate of 62% from the British sample and 50% from the Kuwaiti sample was achieved. 84% of the sample (n=52) were 41 years old or over. The duration of the disease was less than 10 years in 43.4% of British and 68% of Kuwaiti respondents. The majority of British respondents (56.5%) reported the disease severity to be moderate, while the majority of Kuwaitis was mild (72%). The annual relapse rates in Kuwait were relatively low, with 82% of the Kuwaiti sample had one relapse per year, compared to the 64.5% of British. The most common symptoms reported by British respondents were balance (75.8%), fatigue (74.2%), and weakness (71%), and by Kuwaiti respondents were fatigue (86%), balance (76%), and weakness (66%). The help and support for MS were by far more diverse for the British than Kuwaiti respondents. Discussion: The results unveiled marked differences between two groups of British and Kuwaiti MS patients in terms of patients’ age and disease duration, and severity. The overwhelming majority of Kuwaiti patients are young individuals who have been with the disease for a relatively short period of time, and their MS in most cases was mild. On the other hand, British patients were relatively older, many have been with the disease for a long period of time, and their average MS condition was more serious than that of their Kuwaiti counterparts. The main support in Kuwait comes from the neurologist, who primarily prescribe medications and advise patients to try to be active. The Kuwaiti respondents thought that lack of encouragement was the main reason for them not to engage in social activities.

Keywords: multiple sclerosis, Kuwait, exercise, demographic

Procedia PDF Downloads 100

Authors: Rubab Z. Kahlon, Ibtisam Butt, Isma Younis, Aamer G. Mufti

Abstract:

Worldwide lung cancer 1.61 million cases were seen in both genders. Lung carcinoma is the major cause of both morbidity and mortality in the world. Purpose of the present study was to describe the spatio- temporal trends of lung cancer in both genders. A retrospective study was conducted. Total 1498 patients of lung carcinoma were examined. Only lung cancer patients from all over the Punjab were included in the present study. MS Excel 2010 was used for data tabulation and calculation while the Arc GIS version 9.3 was used for geographical representation of the data. 1498 cases of Lung cancer were found from 2008-2012. The number of male patients was 1236 and female was 262. Majority of the patients were from Lahore districts with 807 patients. Lung cancer was more prevalent in male as compared to female in our region. Increase in the prevalence of lung cancer was prominently seen in the most populated and industrial areas of the Punjab province. Time trend of five years showed fluctuation in the lung cancer incidence during the study period.

Keywords: districts, gender, lung cancer trends, Punjab province of Pakistan

Procedia PDF Downloads 516

Authors: Khalil Ahmad Khosa

Abstract:

Pakistan is such a diverse region, it is the center of various religions and settlements long before the creation of the nation that exists today. The country's attraction range from the ruin of the Indus Valley Civilization such as Mohenjo-daro, Harappa and Taxila, to the Himalayan hill stations, which attract those interested in winter sports. Pakistan is home to several mountain peaks over 7000 m, which attracts adventurers and mountaineers from around the world, especially K2.[4] The north part of Pakistan has many old fortresses, ancient architecture and the Hunza and Chitral valley, home to small pre-Islamic Animist Kalash people community. The romance of the historic Khyber Pakhtunkhwa province is timeless and legendary, Punjab province has the site of Alexander's battle on the Jhelum River and the historic city Lahore, Pakistan's cultural capital, with many examples of Mughal architecture such as Badshahi Masjid, Shalimar Gardens, Tomb of Jahangir and the Lahore Fort. Tourism is a growing industry in Pakistan. However, till this date, the government has not be able to take the tourism market seriously within Pakistan. Pakistan is home to a diverse number of tourist attractions which have not been funded or protected due to the government giving the tourism market a low priority.

Keywords: architecture, Pakistan, tourism, turist

Procedia PDF Downloads 264

Authors: Olivia Meeschaert

Abstract:

The Conference of the Parties (COP) refers to the countries that signed on to the United Nations Framework Convention on Climate Change. This annual conference provides a platform for countries to voice their major climate concerns, negotiate on a number of global issues, and come to agreements with the world’s largest emitters on how to make incremental changes that will achieve global climate goals. Historically, the outcome of COP includes major climate pledges and international agreements. COP27 will take place in Egypt at the beginning of November 2022. The 197 parties will come together to develop solutions to the dire consequences of climate change that many people around the world are already experiencing. The war in Ukraine will require a different tone from last year’s COP, particularly given that major impacts of the war are being felt throughout Europe and have had a detrimental effect on the region’s progress in achieving the benchmarks set in their climate pledges. Last year’s COP opened with many climate advocates feeling optimistic but the commitments made in Glasgow have so far remained empty promises, and the main contributors to climate change – China, the European Union, and the United States of America – have not moved fast enough.

Keywords: environment, law and policy, climate change, greenhouse gas, conference of the parties, China, United States, European Union

Procedia PDF Downloads 67

Authors: Abdullah Özbilgin, Oguzhan Kahraman, Mustafa Selçuk Alataş

Abstract:

Plant breeders have made and will continue to make important contributions toward meeting the need for more and better feed and food. The use of new techniques to modify the genetic makeup of plants to improve their properties has led to a new generation of crops, grains and their by-products for feed. Plant breeders have made and will continue to make important contributions toward meeting the need for more and better feed and food. The use of new techniques to modify the genetic makeup of plants to improve their properties has led to a new generation of crops, grains and their by-products for feed. The land area devoted to the cultivation of genetically modified (GM) plants has increased in recent years: in 2012 such plants were grown on over 170 million hectares globally, in 28 different countries, and are at resent used by 17.3 million farmers worldwide. The majority of GM plants are used as feed material for food-producing farm animals. Despite the facts that GM plants have been used as feed for years and a number of feeding studies have proved their safety for animals, they still give rise to emotional public discussion.

Keywords: crops, genetical modified plant(GM), plant, safety

Procedia PDF Downloads 549

Authors: Lu Yung-Hsiang, Chang Kuming, Dai Yi-Fang, Liao Ching-Yi

Abstract:

According to Taiwan’s administrative division of future land planning may lead farmer association and service areas facing recombination or merger. Thus, merger combination and the economic benefit of the farmer association are worth to be discussed. The farmer association in the merger, which may cause some then will not be consolidated, or consolidate two, or ever more to one association. However, under what condition to merge is greatest, as one of observation of this study. In addition, research without using simulation methods and only on the credit department rather whole farmer association. Therefore, this paper will use the simulation approach, and examine both the merge of farmer association and the condition under which the benefits are the greatest. The data of this study set include 266 farmer associations in Taiwan period 2012 to 2013. Empirical results showed that the number of the farmer association optimal simulation combination is 108.After the merger from the first stage can be reduced by 60% of the farmers’ association. The cost saving effects of the post-merger is not different. The cost efficiency of the farmers’ association improved it. The economies of scale and scope would decrease by the merger. The research paper hopes the finding will benefit the future merger of the farmers’ association.

Keywords: simulation merger, farmer association, assurance region, data envelopment analysis

Procedia PDF Downloads 337

Authors: Guannan Ren, Thomas Mazzuchi, Shahram Sarkani

Abstract:

Electric vehicle battery recycling has emerged as a critical process in the transition toward sustainable transportation. As the demand for electric vehicles continues to rise, so does the need to address the end-of-life management of their batteries. Electric vehicle battery recycling benefits resource recovery and supply chain stability by reclaiming valuable metals like lithium, cobalt, nickel, and graphite. The reclaimed materials can then be reintroduced into the battery manufacturing process, reducing the reliance on raw material extraction and the environmental impacts of waste. Current battery recycling rates are insufficient to meet the growing demands for raw materials. While significant progress has been made in electric vehicle battery recycling, many areas can still improve. Standardization of battery designs, increased collection and recycling infrastructures, and improved efficiency in recycling processes are essential for scaling up recycling efforts and maximizing material recovery. This work delves into key factors, such as regulatory frameworks, economic incentives, and technological processes, that influence the cost-effectiveness and efficiency of battery recycling systems. A system dynamics model that considers variables such as battery production rates, demand and price fluctuations, recycling infrastructure capacity, and the effectiveness of recycling processes is created to study how these variables are interconnected, forming feedback loops that affect the overall supply chain efficiency. Such a model can also help simulate the effects of stricter regulations on battery disposal, incentives for recycling, or investments in research and development for battery designs and advanced recycling technologies. By using the developed model, policymakers, industry stakeholders, and researchers may gain insights into the effects of applying different policies or process updates on electric vehicle battery recycling rates.

Keywords: environmental engineering, modeling and simulation, circular economy, sustainability, transportation science, policy

Procedia PDF Downloads 70

Authors: Priyanka Yadav, Rajkumar Ghosh, Alok Saini

Abstract:

Human civilization cannot exist and thrive in the absence of adequate water. As a result, even in smart cities, water plays an important role in human existence. The key causes of this catastrophic water scarcity crisis are lifestyle changes, over-exploitation of groundwater, water over usage, rapid urbanization, and uncontrolled population growth. Furthermore, salty water seeps into deeper aquifers, causing land subsidence. The purpose of this study on artificial groundwater recharge is to address the water shortage in Gomti Nagar, Lucknow. Submersibles are the most common methods of collecting freshwater from groundwater in Gomti Nagar neighbourhood of Lucknow. Gomti Nagar area has a groundwater depletion rate of 1968 m3/day/km2 and is categorized as Zone-A (very high levels) based on the existing groundwater abstraction pattern - A to D. Harvesting rainwater using roof top rainwater harvesting systems (RTRWHs) is an effective method for reducing aquifer depletion in a sustainable water management system. Rainwater collecting using roof top rainwater harvesting systems (RTRWHs) is an effective method for reducing aquifer depletion in a sustainable water conservation system. Due to a water imbalance of 24519 ML/yr, the Gomti Nagar region is facing severe groundwater depletion. According to the Lucknow Development Authority (LDA), the impact of installed RTRWHs (plot area 300 sq. m.) is 0.04 percent of rainfall collected through RTRWHs in Gomti Nagar region of Lucknow. When RTRWHs are deployed in all buildings, their influence will be greater. Bye-laws in India have mandated the installation of RTRWHs on plots greater than 300 sq.m. A better India without any water problem is a pipe dream that may be realized by installing residential and commercial rooftop rainwater collecting systems in every structure. According to the current study, RTRWHs should be used as an alternate source of water to bridge the gap between groundwater recharge and extraction in smart city viz. Gomti Nagar, Lucknow, India.

Keywords: groundwater recharge, RTRWHs, harvested rainwater, rainfall, water extraction

Procedia PDF Downloads 84

Authors: Julie Mariam Abraham, G. J. Melendez-Torres

Abstract:

Background. Maternal mortality is disproportionately higher in low- and middle- income countries (LMICs) compared to other parts of the world. At the current pace of progress, the Sustainable Development Goals for maternal mortality rate will not be achieved by 2030. A variety of factors influence the increased risk of maternal complications in LMICs. These are exacerbated by socio-economic and political factors, including poverty, illiteracy, and gender inequality. This paper aims to use realist synthesis to identify the contexts, mechanisms, and outcomes (CMOs) of maternal health interventions conducted in LMICs to inform evidence-based practice for future maternal health interventions. Methods. In May 2022, we searched four electronic databases for systematic reviews of maternal health interventions in LMICs published in the last five years. We used open and axial coding of CMOs to develop an explanatory framework for intervention effectiveness. Results. After eligibility screening and full-text analysis, 44 papers were included. The intervention strategies and measured outcomes varied within reviews. Healthcare system level contextual factors were the most frequently reported, and infrastructural capacity was the most reported context. The most prevalent mechanism was increased knowledge and awareness. Discussion. Health system infrastructure must be considered in interventions to ensure effective implementation and sustainability. Healthcare-seeking behaviours are embedded within social and cultural norms, environmental conditions, family influences, and provider attitudes. Therefore, effective engagement with communities and families is important to create new norms surrounding pregnancy and delivery. Future research should explore community mobilisation and involvement to enable tailored interventions with optimal contextual fit.

Keywords: maternal mortality, service delivery and organisation, realist synthesis, sustainable development goals, overview of reviews

Procedia PDF Downloads 63

Authors: Benarous Khedidja, Yousfi Mohamed

Abstract:

Infections caused by Candida species manifest in a number of diseases, including candidemia, vulvovaginal candidiasis, endocarditis, and peritonitis. These Candida species have been reported to have lipolytic activity by secretion of lipolytic enzymes such as esterases, lipases and phospholipases. These Extracellular hydrolytic enzymes seem to play an important role in Candida overgrowth. Candidiasis is commonly treated with antimycotics such as clotrimazole and nystatin, which bind to a major component of the fungal cell membrane (ergosterol). This binding forms pores in the membrane that lead to death of the fungus. Due to their secondary effects, scientists have thought of another treatment basing on lipase inhibition but we haven’t found any lipase inhibitors used as candidiasis treatment. In this work, we are interested to lipases inhibitors such as alkaloids as another candidiasis treatment. In the first part, we have proceeded to optimize the alkaloid structures and protein 3D structure using Hyperchem software. Secondly, we have docked inhibitors using Genetic algorithm with GOLD software. The results have shown ten possibilities of binding inhibitor to Candida rugosa lipase (CRL) but only one possibility has been accepted depending on the weakest binding energy.

Keywords: marrubiin, candida rugosa lipase, docking, gold

Procedia PDF Downloads 233

Authors: Leila Maleki, Ahmad Esmali Kooraneh, Hossein Taghi Derakhshi

Abstract:

Neural activity in the human brain starts from the early stages of prenatal development. This activity or signals generated by the brain are electrical in nature and represent not only the brain function but also the status of the whole body. At the present moment, three methods can record functional and physiological changes within the brain with high temporal resolution of neuronal interactions at the network level: the electroencephalogram (EEG), the magnet oencephalogram (MEG), and functional magnetic resonance imaging (fMRI); each of these has advantages and shortcomings. EEG recording with a large number of electrodes is now feasible in clinical practice. Multichannel EEG recorded from the scalp surface provides a very valuable but indirect information about the source distribution. However, deep electrode measurements yield more reliable information about the source locations، Intracranial recordings and scalp EEG are used with the source imaging techniques to determine the locations and strengths of the epileptic activity. As a source localization method, Low Resolution Electro-Magnetic Tomography (LORETA) is solved for the realistic geometry based on both forward methods, the Boundary Element Method (BEM) and the Finite Difference Method (FDM). In this paper, we review The findings EEG- LORETA about epilepsy.

Keywords: epilepsy, EEG, EEG-LORETA

Procedia PDF Downloads 529

Authors: Thitima Chaiyakul

Abstract:

The number of previous literature regarding to the effect of asset growth and equity returns is small. Furthermore, those literature are mainly focus in the developed markets. According to my knowledge, there is no published paper examining the effect of asset growth and equity returns in the Stock Exchange of Thailand in different industry groups. The main objective in this research is the testing the effect of asset growth to equity returns in different industry groups. This study employs the data of the listed companies in the Stock Exchange of Thailand during January 1996 and December 2014. The data of financial industry are exclude from this study due to the different meaning of accounting terms. The results show the supported evidence that the asset growth positively affects the equity returns at a statistically significance level of at least 5% in Agro& Food Industry, Industrials, and Services Industry Groups. These results are inconsistent with the previous research testing in developed markets. Nevertheless, the statistically significances of the effect of asset growth to equity returns appear in some cases. In summary, the asset growth is a non-systematic risk and it is a mispricing factor.

Keywords: asset growth, asset pricing, equity returns, Thailand

Procedia PDF Downloads 335

Authors: Yousif Mohamed Y. Abdallah, Eltayeb Wagi Allah Eltayeb, Mohamed E. Gar-elnabi, Mohamed Ahmed Ali

Abstract:

To characterize coronary artery obstruction and related findings in ischemic heart patients using cardiac scintigraphy for the identification of myocardial ischemia, 146 patients were studied at basal conditions and also asked for fasting after night till the intravenous injection of the radiopharmaceutical. After the injection time about 15 to 20 minutes, the patient should eat a fatty meal and chocolate for the good excretion of the gall bladder, to evaluate the performance and regional wall motion of the left ventricle (LV). The results showed that the body mass index percentage in this sample was in range of 43.05 to 61.05. The number of patients who were catheter candidates were 56 with 43% and the patients that were not candidate to cathode were 74 patients with 57% of all patients. For the group of patients where type of ischemia was assessed, 29.5% of patients had reversible posterior and inferior wall, 15.1% of patients had fixed large from apex to base, 9.6% of patients had mild basal inferior wall, 4.8 % of patients had mild anterior wall, 6.2% of patients had antro-septal and 34.9% of patients had moderate ischemia.

Keywords: myocardial ischemia, myocardial scintigraphy, contrast ventriculography, coronary artery obstruction

Procedia PDF Downloads 572

Authors: Goksen Arik, Mihriban Korukluoglu

Abstract:

Lactic acid bacteria (LAB) and some yeast species are common microorganisms found in dairy products and most of them are responsible for the fermentation of foods. Such cultures are isolated and used as a starter culture in the food industry because of providing standardisation of the final product during the food processing. Choice of starter culture is the most important step for the production of fermented food. Isolated LAB and yeast cultures which have the ability to create a biofilm layer can be preferred as a starter in the food industry. The biofilm formation could be beneficial to extend the period of usage time of microorganisms as a starter. On the other hand, it is an undesirable property in pathogens, since biofilm structure allows a microorganism become more resistant to stress conditions such as antibiotic presence. It is thought that the resistance mechanism could be turned into an advantage by promoting the effective microorganisms which are used in the food industry as starter culture and also which have potential to stimulate the gastrointestinal system. Development of the biofilm layer is observed in some LAB and yeast strains. The resistance could make LAB and yeast strains dominant microflora in the human gastrointestinal system; thus, competition against pathogen microorganisms can be provided more easily. Based on this circumstance, in the study, 10 LAB and 10 yeast strains were isolated from various dairy products, such as cheese, yoghurt, kefir, and cream. Samples were obtained from farmer markets and bazaars in Bursa, Turkey. As a part of this research, all isolated strains were identified and their ability of biofilm formation was detected with two different methods and compared with each other. The first goal of this research was to determine whether isolates have the potential for biofilm production, and the second was to compare the validity of two different methods, which are known as “Tube method” and “96-well plate-based method”. This study may offer an insight into developing a point of view about biofilm formation and its beneficial properties in LAB and yeast cultures used as a starter in the food industry.

Keywords: biofilm, dairy products, lactic acid bacteria, yeast

Procedia PDF Downloads 248

Authors: Aqleem Fatimah

Abstract:

The purpose of study was to find out the impact of teachers’ gender on students’ score achievement. Focusing on primary level’s teachers & students, a survey research was conducted by using convenient sampling technique. All the students of grade four (1500) and fifty-six teachers (equally divided by gender) from the 50 randomly selected coeducational schools from Lahore were taken as sample. The academic performance was operationalized using a t-test on standardized achievement tests of the students in language, science mathematics and social studies. In addition, all those gender based characteristics of teachers that count a lot in classroom interactions (taking Multi-grade classes, classroom strategies, feedback strategies and evaluation method) that influence students’ achievement were also analyzed by using a questionnaire and an observation schedule. The results of the study showed better academic achievement of students (girl &boy) of female teachers comparatively to the students of male teachers. Therefore, as the female teachers’ number lacks in Pakistan, the study suggests policy makers to seek guidelines to induct more specialized and professionally competent female teachers because their induction will prove highly beneficial for the betterment of students’ score achievement.

Keywords: gender, teacher, competency, score achievement

Procedia PDF Downloads 306

Authors: Chien-Song Chyang

Abstract:

For a fluidized-bed combustion system, excess air ratio (EAR) and superficial velocity are major operating parameters affecting combustion behaviors, and these 2 factors are dependent variables since both fluidizing gas and combustion-supporting agent are air. EAR will change when superficial velocity alters, so that the effect of superficial velocity and/or EAR on combustion behaviors cannot be examined under a specific condition. When stage combustion is executed, one can discuss the effect of EAR under a certain specific superficial velocity, but the flow rate of secondary air and EAR are dependent. In order to investigate the effect of excess air ratio on the combustion behavior of a fluidized combustion system, the flue gas recirculation was adapted by the author in 2007. We can maintain a fixed flow rate of primary gas or secondary gas and change excess oxygen as an independent variable by adjusting the recirculated flue gas appropriately. In another word, we can investigate the effect of excess oxygen on the combustion behavior at a certain primary gas flow, or at a certain hydrodynamics conditions. This technique can be used at a lower turndown ratio to maintain the residual oxygen in the flue gas at a certain value. All the experiments were conducted in a pilot scale fluidized bed combustor. The fluidized bed combustor can be divided into four parts, i.e., windbox, distributor, combustion chamber, and freeboard. The combustion chamber with a cross-section of 0.8 m × 0.4 m was constructed of 6 mm carbon steel lined with 150 mm refractory to reduce heat loss. Above the combustion chamber, the freeboard is 0.64 m in inner diameter. A total of 27 tuyeres with orifices of 5 and 3 mm inside diameters mounted on a 6 mm stainless-steel plate were used as the gas distributor with an open-area-ratio of 0.52%. The Primary gas and secondary gas were fixed at 3 Nm3/min and 1 Nm3/min respectively. The bed temperature was controlled by three heat transfer tubes inserted into the bubbling bed zone. The experimental data shows that bed temperature, CO and NO emissions increase with the stoichiometric oxygen of the primary gas. NO emissions decrease with the stoichiometric oxygen of the primary. Compared with part of primary air substituted with nitrogen, a lower NO emission can be obtained while flue gas recirculation applies as part of primary air.

Keywords: fluidized bed combustion, flue gas circulation, NO emission, recycle

Procedia PDF Downloads 173

Authors: Isabel Jones

Abstract:

As adolescence is a formative time, experiences during adolescence often affect the rest of one’s life. Therefore, dating, specifically violence in dating, can have lasting effects on the rest of one’s life. In order to find sources, searches were conducted on PsycINFO, specifically EBSCO, and narrowed down under the criteria that the source contained information about adolescent dating violence rather than adult, and focused on causes, effects, or prevention methods. This literature review examines research regarding the effects and causes of TDV, and then what methods are effective in the prevention of TDV development. This will allow for a clear image of how these prevention methods are effective and why they are important. Effects of TDV extend beyond the physical, including psychological and sexual long-lasting effects. These are caused by a number of concepts, including learned behavior, inhibitory issues/substance abuse, and cultural factors. When both of these are taken into account, preventative measures such as school-based interventions, parental/adult monitoring, and the presence of positive family examples are more clear as to their effectiveness. This literature review may provide further awareness to this public health crisis and give the public a view of how adolescents are affected by TDV on their path from child to adult.

Keywords: adolescence, dating violence, risk factors, predictors, relationship

Procedia PDF Downloads 54

Authors: Heesuk Seo, Yongtae Kim

Abstract:

Online learning started in the 1990s, the spread of the Internet has been through the era of e-learning paradigm of online education in the era of smart learning change. Reflecting the different nature of the mobile to anywhere anytime, anywhere was also allows the form of learning, it was also available through the learning content and interaction. We are developing a cloud system, 'TLINKS CLOUD' that allows you to configure the environment of the smart learning without the need for additional infrastructure. Using the big-data analysis for e-learning contents, we provide an integrated solution for e-learning tailored to individual study.

Keywords: authority tool, big data analysis, e-learning, HTML5

Procedia PDF Downloads 396

Authors: Mahsa Falahatpour

Abstract:

Introduction: This study aims to explore how inter-observer variability in manual tumor segmentation impacts the reliability of radiomic features in non–small cell lung cancer (NSCLC). Methods: The study included twenty-three NSCLC tumors. Each patient had three tumor segmentations (VOL1, VOL2, VOL3) contoured on PET/CT scans by three radiation oncologists. Dice coefficients (DCS) were used to measure the segmentation variability. Radiomic features were extracted with 3D-slicer software, consisting of 66 features: first-order (n=15), second-order (GLCM, GLDM, GLRLM, and GLSZM) (n=33). The inter-observer variability of radiomic features was assessed using the intraclass correlation coefficient (ICC). An ICC > 0.8 indicates good stability. Results: The mean DSC of VOL1, VOL2, and VOL3 was 0.80 ± 0.04, 0.85 ± 0.03, and 0.76 ± 0.06, respectively. 92% of all extracted radiomic features were found to be stable (ICC > 0.8). The GLCM texture features had the highest stability (96%), followed by GLRLM features (90%) and GLSZM features (87%). The DSC was found to be highly correlated with the stability of radiomic features. Conclusion: The variability in inter-observer segmentation significantly impacts radiomics analysis, leading to a reduction in the number of appropriate radiomic features.

Keywords: PET/CT, radiomics, radiotherapy, segmentation, NSCLC

Procedia PDF Downloads 20

Authors: Sanoj Sahu, Ramakar Jha

Abstract:

Odisha (India) is in need of reliable, cost-effective power generation. A prolonged electricity crisis and increasing power demand have left over thousands of citizens without access to electricity, and much of the population suffers from sporadic outages. The purpose of this project is to build a methodology to evaluate small hydropower potential, which can be used to alleviate the Odisha’s energy problem among rural communities. This project has three major tasks: the design of a simple SHEP for a single location along a river in the Odisha; the development of water flow prediction equations through a linear regression analysis; and the design of an ArcGIS toolset to estimate the flow duration curves (FDCs) at locations where data do not exist. An explanation of the inputs to the tool, as well has how it produces a suitable output for SHEP evaluation will be presented. The paper also gives an explanation of hydroelectric power generation in the Odisha, SHEPs, and the technical and practical aspects of hydroelectric power. Till now, based on topographical and rainfall analysis we have located hundreds of sites. Further work on more number of site location and accuracy of location is to be done.

Keywords: small hydropower, ArcGIS, rainfall analysis, Odisha’s energy problem

Procedia PDF Downloads 438

Authors: Ana Violante, Jodie Maccarrone, Maria Fimiani

Abstract:

In the United States, over 30 million people are hospitalized annually for conditions that require acute, 24-hour, supervised care. The experience of hospitalization can be traumatic, exposing the patient to loss of control, autonomy, and productivity. Furthermore, 40% of patients admitted to hospitals for general medical illness have a comorbid psychiatric diagnosis. Research suggests individuals admitted with psychiatric comorbidities experience poorer health outcomes, higher utilization rates and increased overall cost of care. Empirical work suggests hospital settings that include a consultation liaison (CL) service report reduced length of stay, lower costs per patient, improved medical staff and patient satisfaction and reduced readmission after 180 days. Despite the overall positive impact CL services can have on patient care, it is estimated that only 1% - 2.8% of hospital admits receive these services, and most research has been conducted by the field of psychiatry. Health psychologists could play an important role in increasing access to this valuable service, though the extent to which health psychologists participate in CL settings is not well known. Objective: Outline the preliminary findings from an empirical study to understand how many APPIC internship training programs offer adult consultation liaison rotations within inpatient hospital settings nationally, as well as describe the specific nature of these training experiences. Research Method/Design: Data was exported into Excel from the 2022-2023 APPIC Directory categorized as “health psychology” sites. It initially returned a total of 537 health training programs out 1518 total programs (35% of all APPIC programs). A full review included a quantitative and qualitative comprehensive review of the APPIC program summary, the site website, and program brochures. The quantitative review extracted the number of training positions; amount of stipend; location or state of program, patient, population, and rotation. The qualitative review examined the nature of the training experience. Results: 29 (5%) of all APPIC health psychology internship training programs (2%) respectively of all APPIC training internship programs offering internship CL training were identified. Of the 29 internship training programs, 16 were exclusively within a pediatric setting (55%), 11 were exclusively within an adult setting (38%), and two were a mix of pediatric and adult settings (7%). CL training sites were located to 19 states, offering a total of 153 positions nationally, with Florida containing the largest number of programs (4). Only six programs offered 12-month training opportunities while the rest offered CL as a major (6 month) to minor (3-4 month) rotation. The program’s stipend for CL training positions ranged from $25,000 to $62,400, with an average of $32,056. Conclusions: These preliminary findings suggest CL training and services are currently limited. Training opportunities that do exist are mostly limited to minor, short rotations and governed by psychiatry. Health psychologists are well-positioned to better define the role of psychology in consultation liaison services and enhance and formalize existing training protocols. Future research should explore in more detail empirical outcomes of CL services that employ psychology and delineate the contributions of psychology from psychiatry and other disciplines within an inpatient hospital setting.

Keywords: consultation liaison, health psychology, hospital setting, training

Procedia PDF Downloads 68

Authors: Sunil Kumar

Abstract:

For many years, small organic molecules derived naturally from microbes and plants have delivered a number of expedient therapeutic drug agents. The search for naturally occurring lead compounds has continued in recent years as well, with the constituents of marine flora and fauna along with those of telluric microorganisms and plants being investigated for their anti-bacterial and anti-cancer activities. It has been observed that such promising lead molecules incline to promptly generate substantial attention among scientists like synthetic organic chemists and biologists. Subsequently, the availability of a given precious natural product sample may be enriched, and it may be possible to determine a preliminary idea of structure-activity relationships to develop synthetic analogues. For instance, anti-tumor drug topotecan is a synthetic chemical compound similar in chemical structure to camptothecin which is found in extracts of Camptotheca acuminate. Similarly, researchers at AstraZeneca discovered anti-biotic pyrrolamide through a fragment-based lead generation approach from kibdelomycin, which is isolated from Staphylococcus aureuss.

Keywords: anticancer, antibiotic, lead molecule, natural product, synthetic analogues

Procedia PDF Downloads 137

Authors: Alami Ilyass, Kharchoufa Loubna, Alachouri Mostafa

Abstract:

Cardiovascular disease (CDV) remains the major cause of morbidity; mortality and disability throughout the world. The ethnopharmcological and ethnobotanical studies are the paramount importance to set a high value on phytogenetic resources and to address health problems of some communities; especially poor peoples. Our work presents an analysis of published data from studies, that have been undertaken, in Morocco, by different seeker teams in separately areas during the last decades. Objectives: Evaluate and identify medicinal plants used for cardiovascular treatment by Moroccan people. Methodology: All these studies have the same approaches ; they were conducted by interviewing people suffering from diabetes. We use Factorial Analysis (FA) and principal Components analysis (PCA) to analyse the aggregated data from the different studies. Results: globally; 95 plants species were listed; all these plant were used empirically by Moroccan society for treating cardiovascular problems. These plants were divided in to 42 families and 87 genus. The lamiaceae; asteraceae; Apiaceae and poaceae are the botanical families with high number of plant species. Coclusion: Traditional medecine has been widely used for treatment of cardiovascular problems and it has been recognized as an interesting alternative to conventional medicine.

Keywords: cardiovascular, ethnobotanical, medicinal plants, Morocco

Procedia PDF Downloads 226

Authors: Mohamad Alkhalidi, S. Neelamani, Noor Alanjari

Abstract:

The main purpose of harbors and marinas is to create a calm and safe docking space for marine vessels. Standard rubble mound breakwaters, although widely used, occupy port space and require large amounts of stones or rocks. Kuwait does not have good quality stone, so they are imported at a very high cost. Therefore, there is a need for a new wave energy dissipating structure where stones and rocks are scarce. While permeable slotted vertical walls have been proved to be a suitable alternative to rubble mound breakwaters, the introduction of sloped slotted walls may be more efficient in dissipating wave energy. For example, two slotted barriers with 60degree inclination may be equivalent to three vertical slotted barriers from wave energy dissipation point of view. A detailed physical model study is carried out to determine the effects of slope angle, porosity, and a number of walls on wave energy dissipation for a wide range of random and regular waves. The results of this study can be used to improve and optimize energy dissipation and reduce construction cost.

Keywords: porosity, slope, wave reflection, wave transmission

Procedia PDF Downloads 281

Authors: Fitih Ademe, Kibebew Kibret, Sheleme Beyene, Mezgebu Getnet, Gashaw Meteke

Abstract:

Changes in precipitation, temperature and atmospheric CO2 concentration are expected to alter agricultural productivity patterns worldwide. The interactive effects of soil moisture and nutrient availability are the two key edaphic factors that determine crop yield and are sensitive to climatic changes. The study assessed the potential impacts of climate change on maize yield and corresponding water productivity and nutrient use efficiency under climate change scenarios for the Central Rift Valley of Ethiopia by mid (2041-2070) and end century (2071-2100). Projected impacts were evaluated using climate scenarios generated from four General Circulation Models (GCMs) dynamically downscaled by the Swedish RCA4 Regional Climate Model (RCM) in combination with two Representative Concentration Pathways (RCP 4.5 and RCP8.5). Decision Support System for Agro-technology Transfer cropping system model (DSSAT-CSM) was used to simulate yield, water and nutrient use for the study periods. Results indicate that rainfed maize yield might decrease on average by 16.5 and 23% by the 2050s and 2080s, respectively, due to climate change. Water productivity is expected to decline on average by 2.2 and 12% in the CRV by mid and end centuries with respect to the baseline. Nutrient uptake and corresponding nutrient use efficiency (NUE) might also be negatively affected by climate change. Phosphorus uptake probably will decrease in the CRV on average by 14.5 to 18% by 2050s, while N uptake may not change significantly at Melkassa. Nitrogen and P use efficiency indicators showed decreases in the range between 8.5 to 10.5% and between 9.3 to 10.5%, respectively, by 2050s relative to the baseline average. The simulation results further indicated that a combination of increased water availability and optimum nutrient application might increase both water productivity and nutrient use efficiency in the changed climate, which can ensure modest production in the future. Potential options that can improve water availability and nutrient uptake should be identified for the study locations using a crop modeling approach.

Keywords: crop model, climate change scenario, nutrient uptake, nutrient use efficiency, water productivity

Procedia PDF Downloads 70

Authors: Niaz Gharavi, Hexin Zhang

Abstract:

In the structural timber design, the shear modulus of the timber beam is an important factor that needs to be determined accurately. According to BS EN 408, shear modulus can be determined using torsion test or shear field test method. Although torsion test creates pure shear status in the beam, it does not represent the real-life situation when the beam is in the service. On the other hand, shear field test method creates similar loading situation as in reality. The latter method is based on shear distortion measurement of the beam at the zone with the constant transverse load in the standardized four-point bending test as indicated in BS EN 408. Current testing practice code advised using two metallic arms act as an instrument to measure the diagonal displacement of the constructing square. Timber is not a homogenous material, but a heterogeneous and this characteristic makes timber to undergo a non-uniform deformation. Therefore, the dimensions and the location of the constructing square in the area with the constant transverse force might alter the shear modulus determination. This study aimed to investigate the impact of the shape, size, and location of the square in the shear field test method. A binocular stereo vision system was developed to capture the 3D displacement of a grid of target points. This approach is an accurate and non-contact method to extract the 3D coordination of targeted object using two cameras. Two group of three glue laminated beams were produced and tested by the mean of four-point bending test according to BS EN 408. Group one constructed using two materials, laminated bamboo lumber and structurally graded C24 timber and group two consisted only structurally graded C24 timber. Analysis of Variance (ANOVA) was performed on the acquired data to evaluate the significance of size and location of the square in the determination of shear modulus of the beam. The results have shown that the size of the square is an affecting factor in shear modulus determination. However, the location of the square in the area with the constant shear force does not affect the shear modulus.

Keywords: shear field test method, BS EN 408, timber shear modulus, photogrammetry approach

Procedia PDF Downloads 198

Authors: Ali Maksum

Abstract:

In a number of countries, including Indonesia, the tendency for non-communicable diseases is increasing. As a result, health costs must be paid by the state continues to increase as well. People's lifestyles, including due to lack of physical activity, are thought to have contributed significantly to the problem. This study aims to examine the impact of participation in sports on quality of life, which is reflected in three main indicators, namely health, psychological, and social aspects. The study was conducted in the city of Surabaya and its surroundings, with a total of 490 participants, consisting of 245 men and 245 women with an average age of 45.4 years. Data on physical activity and quality of life were collected by questionnaire and analyzed using structural equation modeling. The test results of the model prove that the value of chi-square = 8,259 with p = .409, RMSEA = .008, NFI = .992, and CFI = 1. This means that the model is compatible with the data. The model explains that physical activity has a significant effect on quality of life. People who exercise regularly are better able to cope with stress, have a lower risk of illness, and have higher pro-social behavior. Therefore, it needs serious efforts from stakeholders, especially the government, to create an ecosystem that allows the growth of movement culture in the community.

Keywords: participation, physical activity, quality of life, structural equation modelling

Procedia PDF Downloads 108

Authors: N. D. Hiripitiya, H. V. H. De Soysa, H. S. U. Thrimavithana, B. R. Epitawala, K. A. D. D. Kuruppu, D. J. K. Lokupathirage

Abstract:

This research was related to identify the reasons which lead for early wear and tear of aircraft tyres. Further this research focused to rectify those issues in tyres with some modifications. The aircraft tyres of Y12 aircraft was selected for the study as due to Y12 aircraft fly frequently. Self-structured questionnaire was prepared and it was distributed among Y12 aircraft technicians. Based on their feedback several issues were identified related to tyre wear and tear. One of the reasons was uneven tyre wearing. But it could rectify after interchanging the tyre sides after completion of 50 landings. Several modifications were done in order to rectify all the identified issues. Several devices were constructed in order to enhance the life time of the Y12 aircraft tyre. Mechanical properties were measured for the worn-out tyres. The properties were compared with the control tyre sample. It was found that there was an average increment of tensile strength by 38.14 % of control tyre, when compared with the worn-out tyres which were completed 50 number of landings. The suggested modifications are in the process of implementation. It is confident that above mentioned solutions will lead to increase the life span of tyres in Y12 aircraft.

Keywords: aircraft, devices, enhance life span, modifications for tyre wear

Procedia PDF Downloads 274

Authors: Bandar A. Alkhayyal

Abstract:

Modern supply chains are typically linear, transforming virgin raw materials into products for end consumers, who then discard them after use to landfills or incinerators. Nowadays, there are major efforts underway to create a circular economy to reduce non-renewable resource use and waste. One important aspect of these efforts is the development of Green Supply Chain (GSC) systems which enables a reverse flow of used products from consumers back to manufacturers, where they can be refurbished or remanufactured, to both economic and environmental benefit. This paper develops novel multi-objective optimization models to inform GSC system design at multiple levels: (1) strategic planning of facility location and transportation logistics; (2) tactical planning of optimal pricing; and (3) policy planning to account for potential valuation of GSC emissions. First, physical linear programming was applied to evaluate GSC facility placement by determining the quantities of end-of-life products for transport from candidate collection centers to remanufacturing facilities while satisfying cost and capacity criteria. Second, disassembly and remanufacturing processes have received little attention in industrial engineering and process cost modeling literature. The increasing scale of remanufacturing operations, worth nearly $50 billion annually in the United States alone, have made GSC pricing an important subject of research. A non-linear physical programming model for optimization of pricing policy for remanufactured products that maximizes total profit and minimizes product recovery costs were examined and solved. Finally, a deterministic equilibrium model was used to determine the effects of internalizing a cost of GSC greenhouse gas (GHG) emissions into optimization models. Changes in optimal facility use, transportation logistics, and pricing/profit margins were all investigated against a variable cost of carbon, using case study system created based on actual data from sites in the Boston area. As carbon costs increase, the optimal GSC system undergoes several distinct shifts in topology as it seeks new cost-minimal configurations. A comprehensive study of quantitative evaluation and performance of the model has been done using orthogonal arrays. Results were compared to top-down estimates from economic input-output life cycle assessment (EIO-LCA) models, to contrast remanufacturing GHG emission quantities with those from original equipment manufacturing operations. Introducing a carbon cost of $40/t CO2e increases modeled remanufacturing costs by 2.7% but also increases original equipment costs by 2.3%. The assembled work advances the theoretical modeling of optimal GSC systems and presents a rare case study of remanufactured appliances.

Keywords: circular economy, extended producer responsibility, greenhouse gas emissions, industrial ecology, low carbon logistics, green supply chains

Procedia PDF Downloads 152

Authors: Amylyn F. Labasano

Abstract:

A significant number of empirical studies are carried out to investigate factors affecting college students’ performance in the academic examination. With a wide-array of literature-and studies-supported findings, this study is limited only on the students’ probability of passing periodical exams which is associated with students’ gender, absences in the class, use of reference book, and hours of study. Binary logistic regression was the technique used in the analysis. The research is based on the students’ record and data collected through survey. The result reveals that gender, use of reference book and hours of study are significant predictors of passing an examination while students’ absenteeism is an insignificant predictor. Females have 45% likelihood of passing the exam than their male classmates. Students who use and read their reference book are 38 times more likely pass the exam than those who do not use and read their reference book. Those who spent more than 3 hours in studying are four (4) times more likely pass the exam than those who spent only 3 hours or less in studying.

Keywords: absences, binary logistic regression, gender, hours of study prediction-causation method, periodical exams, random sampling, reference book

Procedia PDF Downloads 294