Search results for: work roll shifting

Authors: S. Thanabanjerdsin, F. Srisuriyachai, J. Chewaroungroj

Abstract:

Drilling horizontal well is one of the most cost-effective method to exploit reservoir by increasing exposure area between well and formation. Together with horizontal well technology, intelligent completion is often co-utilized to increases petroleum production by monitoring/control downhole production. Combination of both technological results in an opportunity to lower water cresting phenomenon, a detrimental problem that does not lower only oil recovery but also cause environmental problem due to water disposal. Flow of reservoir fluid is a result from difference between reservoir and wellbore pressure. In horizontal well, reservoir fluid around the heel location enters wellbore at higher rate compared to the toe location. As a consequence, Oil-Water Contact (OWC) at the heel side of moves upward relatively faster compared to the toe side. This causes the well to encounter an early water encroachment problem. Installation of Inflow Control Valve (ICV) in particular sections of horizontal well can involve several parameters such as number of ICV, water cut constrain of each valve, length of each section. This study is mainly focused on optimization of ICV configuration to minimize water production and at the same time, to enhance oil production. A reservoir model consisting of high aspect ratio of oil bearing zone to underneath aquifer is drilled with horizontal well and completed with variation of ICV segments. Optimization of the horizontal well configuration is firstly performed by varying number of ICV, segment length, and individual preset water cut for each segment. Simulation results show that installing ICV can increase oil recovery factor up to 5% of Original Oil In Place (OOIP) and can reduce of produced water depending on ICV segment length as well as ICV parameters. For equally partitioned-ICV segment, more number of segment results in better oil recovery. However, number of segment exceeding 10 may not give a significant additional recovery. In first production period, deformation of OWC strongly depends on number of segment along the well. Higher number of segment results in smoother deformation of OWC. After water breakthrough at heel location segment, the second production period begins. Deformation of OWC is principally dominated by ICV parameters. In certain situations that OWC is unstable such as high production rate, high viscosity fluid above aquifer and strong aquifer, second production period may give wide enough window to ICV parameter to take the roll.

Keywords: horizontal well, water cresting, inflow control valve, reservoir simulation

Procedia PDF Downloads 409

Authors: Juhi Faridi, Mohd. Ajmal Kafeel

Abstract:

The advancements in the field of Artificial Intelligence (AI) and technology has led to an evolution of an intelligent era. Neural networks, having the computational power and learning ability similar to the brain is one of the key AI technologies. Neuromorphic computing system (NCS) consists of the synaptic device, neuronal circuit, and neuromorphic architecture. Memristor are a promising candidate for neuromorphic computing systems, but when it comes to neuromorphic computing, the conductance behavior of the synaptic memristor or neuronal memristor needs to be studied thoroughly in order to fathom the neuroscience or computer science. Furthermore, there is a need of more simulation work for utilizing the existing device properties and providing guidance to the development of future devices for different performance requirements. Hence, development of NCS needs more simulation work to make use of existing device properties. This work aims to provide an insight to build neuronal circuits using memristors to achieve a Memristor based NCS.  Here we throw a light on the research conducted in the field of memristors for building analog and digital circuits in order to motivate the research in the field of NCS by building memristor based neural circuits for advanced AI applications. This literature is a step in the direction where we describe the various Key findings about memristors and its analog and digital circuits implemented over the years which can be further utilized in implementing the neuronal circuits in the NCS. This work aims to help the electronic circuit designers to understand how the research progressed in memristors and how these findings can be used in implementing the neuronal circuits meant for the recent progress in the NCS.

Keywords: analog circuits, digital circuits, memristors, neuromorphic computing systems

Procedia PDF Downloads 166

Authors: Lana Whiskeyjack, Kyle Napier

Abstract:

The Spirit of the language embodies the motivation for indigenous people to connect with the indigenous language of their lineage. While the concept of the spirit of the language is often woven into the discussion by indigenous language revitalizationists, particularly those who are indigenous, there are few tangible terms in academic research conceptually actualizing the term. Through collaborative work with indigenous language speakers, elders, and learners, this research sets out to identify the spirit of the language, the catalysts of disconnection from the spirit of the language, and the sources of reconnection to the spirit of the language. This work fundamentally addresses the terms of engagement around collaboration with indigenous communities, itself inviting a decolonial approach to community outreach and individual relationships. As indigenous researchers, this means beginning, maintain, and closing this work in the ceremony while being transparent with community members in this work and related publishing throughout the project’s duration. Decolonizing this approach also requires maintaining explicit ongoing consent by the elders, knowledge keepers, and community members when handling their ancestral and indigenous knowledge. The handling of this knowledge is regarded in this work as stewardship, both in the handling of digital materials and the handling of ancestral Indigenous knowledge. This work observes recorded conversations in both nêhiyawêwin and English, resulting from 10 semi-structured interviews with fluent nêhiyawêwin speakers as well as three structured dialogue circles with fluent and emerging speakers. The words were transcribed by a speaker fluent in both nêhiyawêwin and English. The results of those interviews were categorized thematically to conceptually actualize the spirit of the language, catalysts of disconnection to thespirit of the language, and community voices methods of reconnection to the spirit of the language. Results of these interviews vastly determine that the spirit of the language is drawn from the land. Although nêhiyawêwin is the focus of this work, Indigenous languages are by nature inherently related to the land. This is further reaffirmed by the Indigenous language learners and speakers who expressed having ancestries and lineages from multiple Indigenous communities. Several other key differences embody this spirit of the language, which include ceremony and spirituality, as well as the semantic worldviews tied to polysynthetic verb-oriented morphophonemics most often found in indigenous languages — and of focus, nêhiyawêwin. The catalysts of disconnection to the spirit of the language are those whose histories have severed connections between Indigenous Peoples and the spirit of their languages or those that have affected relationships with the land, ceremony, and ways of thinking. Results of this research and its literature review have determined the three most ubiquitously damaging interdependent factors, which are catalysts of disconnection from the spirit of the language as colonization, capitalism, and Christianity. As voiced by the Indigenous language learners, this work necessitates addressing means to reconnect to the spirit of the language. Interviewees mentioned that the process of reconnection involves a whole relationship with the land, the practice of reciprocal-relational methodologies for language learning, and indigenous-protected and -governed learning. This work concludes in support of those reconnection methodologies.

Keywords: indigenous language acquisition, indigenous language reclamation, indigenous language revitalization, nêhiyawêwin, spirit of the language

Procedia PDF Downloads 138

Authors: B. G. Sheeparamatti, Prashant Hanasi, Vanita Abbigeri

Abstract:

The objective of this work is to carry out a critical comparison of different actuation mechanisms like electrostatic, thermal, piezoelectric, and magnetic with reference to a microcantilever. The relevant parameters like force generated, displacement are compared in actuation methods. With these results, they help in choosing the best actuation method for a particular application. In this study, Comsol/Multiphysics software is used. Modeling and simulation are done by considering the microcantilever of same dimensions as an actuator using all the above-mentioned actuation techniques. In addition to their small size, micro actuators consume very little power and are capable of accurate results. In this work, a comparison of actuation mechanisms is done to decide the efficient system in the micro domain.

Keywords: actuation techniques, microswitch, micro actuator, microsystems

Procedia PDF Downloads 401

Authors: Anas M. Fares

Abstract:

Reinforced concrete shear walls are the most frequently used forms of lateral resisting structural elements. These walls may take many forms due to their functions and locations in the building. In Palestine, the most lateral resisting forces construction forms is the cantilever shear walls system. It is thus of prime importance to study the rigidity of these walls. The virtual work theorem is used to derive the total lateral deflection of cantilever shear walls due to flexural and shear deformation. The case of neglecting the shear deformation in the walls is also studied, and it is found that the wall height to length aspect ratio (H/B) plays a major role in calculating the lateral deflection and the rigidity of such walls. When the H/B is more than or equal to 3.7, the shear deformation may be neglected from the calculation of the lateral deflection. Moreover, the walls with the same material properties, same lateral load value, and same aspect ratio, shall have the same of both the lateral deflection and the rigidity. Finally, an equation to calculate the total rigidity and total deflection of such walls is derived by using the virtual work theorem for a cantilever beam.

Keywords: cantilever shear walls, flexural deformation, lateral deflection, lateral loads, reinforced concrete shear walls, rigidity, shear deformation, virtual work theorem

Procedia PDF Downloads 215

Authors: Nordin Mamat, Abdul Rahim Razalli, Loy Chee Luen, Abdul Talib Hashim

Abstract:

This study was designed to investigate preschool environment in multi-ethnic preschool in Malaysia. The objectives are to identify the quality of work environment in multi-ethnic preschools; to investigate the practices of teachers’ role and responsibility; and to identify the quality of human resources. The study involved 2004 respondents who are the staff of multi-ethnic preschool from the government agency who provide preschool service. This study was conducted using a mixed method in which questionnaires and interviews were used to obtain data from respondents. The findings were analysed using mean and used Likert scale to determine the three-stage level such as the high, moderate and low. Findings indicated that the work environment at a moderate level, but the facilities provided insufficient to carry out educational activities with children. The result based on ranking of duties and responsibilities of teachers in multi-ethnic preschool shows the teachers practice daily record of children's development is very little, that only 65 persons are recording the child's development. The poor ratio of teachers and child in multi-ethnic preschool is between 25 to 35 children per class which means the children need a lot of attention. Meanwhile, the work environment is moderate with a mean score of 3.65 and overall mean score for level of staff career development 3.66 also moderate. The findings indicate the facilities provided in their workplace and staff career development requires improvements. Overall, the level of work environment is moderate, and it needs an improvement in term of facilities.

Keywords: environment, human resources, multi-ethnic preschool, quality teacher

Procedia PDF Downloads 318

Authors: Belkis L. Cabrera

Abstract:

Contemporary technological innovations have reshaped possibility, interaction, communication, engagement, education, and training. Indeed, today, a high-quality technology enhanced learning experience can be transformative as much for the learner as for the educator-trainer. As innovative technologies continue to facilitate, support, foster, and enhance collaboration, problem-solving, creativity, adaptiveness, multidisciplinarity, and communication, the field of instructional design (ID) also continues to develop and expand. Shifting its focus from media to the systematic design of instruction, or rather from the gadgets and devices themselves to the theories, models, and impact of implementing educational technology, the evolution of ID marks a restructuring of the teaching, learning, and training paradigms. However, with all of its promise, this latter component of ID remains underdeveloped. The majority of ID models are crafted and guided by learning theories and, therefore, most models are constructed around student and educator roles rather than trainer roles. Thus, when these models or systems are employed for training purposes, they usually have to be re-fitted, tweaked, and stretched to meet the training needs. This paper is concerned with the training or professional development (PD) facet of instructional design and how ID models built on teacher-to-teacher interaction and dialogue can support the creation of professional learning communities (PLCs) or communities of practice (CoPs), which can augment learning and PD experiences for all. Just as technology is changing the face of education, so too can it change the face of PD within the educational realm. This paper not only provides a new ID model but using innovative technologies such as Padlet and Thinkbinder, this paper presents a concrete example of how a traditional body-to-body, brick, and mortar learning community can be transferred and transformed into the online context.

Keywords: communities of practice, e-learning, educational reform, instructional design, professional development, professional learning communities, technology, training

Procedia PDF Downloads 337

Authors: Wafa Ghonaim

Abstract:

Though quite fast on growth, Islamic financing at large, and its diverse instruments, is a controversial matter among scholars. This is evident from the ongoing debates on its Shariah compliance. Arguments, however, are inciting doubts and concerns among clients about its credibility, which is harming this lucrative sector. The work here investigates, particularly, some issues related to the Tawarruq instrument. The work examines the issues of linking Murabaha and Wakala contracts, the reselling of commodities to same traders, and the transfer of ownerships. The work affirms that a multi-agent smart electronic market design would facilitate Shariah compliance. The smart market exploits the rational decision-making capabilities of autonomous proxy agents that enable the clients, traders, brokers, and the bank buy and sell commodities, and manage transactions and cash flow. The smart electronic market design delivers desirable qualities that terminate the need for Wakala contracts and the reselling of commodities to the same traders. It also resolves the ownership transfer issues by allowing stakeholders to trade independently. The bank administers the smart electronic market and assures reliability of trades, transactions and cash flow. A multi-agent simulation is presented to validate the concept and processes. We anticipate that the multi-agent smart electronic market design would deliver Shariah compliance of personal financing to the aspiration of scholars, banks, traders and potential clients.

Keywords: Islamic finance, share'ah compliance, smart electronic markets design, multiagent systems

Procedia PDF Downloads 312

Authors: Shalini Misra

Abstract:

The means and methods of education have been changing fast since the invention of internet. Both, ancient and modern education emphasized on the holistic development of students. But, a significant change has been observed in the 21st century learners. Online classes, intercultural and interdisciplinary education which were exceptions in the past, are setting new trends in the field of education. In the modern era, intercultural and interpersonal skills are of immense importance, not only for students but for everyone. It sets a platform for better understanding and deeper learning by ensuring the active participation and involvement of students belonging to different social and cultural backgrounds in various academic and non-academic pursuits. On October 31, 2015, on the occasion of 140th birth anniversary of Sardar Vallabhbhai Patel, Hon’ble Prime Minister of India, Narendra Modi announced a wonderful initiative, ‘Ek Bharat Shreshtha Bharat’ i.e. ‘One India Best India’ commonly known as ‘EBSB’. The program highlighted India’s rich culture and traditions. The objective of the program was to foster a better understanding and healthy relationship among Indian States. Under this program, a variety of subjects were covered like ‘Arts, Culture and Language’ .It was claimed to be a successful cultural exchange where students from diverse communities shared their thoughts and experiences with one another. Under this online cultural exchange program, the state of Uttarakhand was paired with the state of Karnataka in the year 2022. The present paper proposes to undertake a survey of a total of thirty secondary level students of Uttarakhand and the partner state Karnataka, who participated in this program with a purpose of learning and embracing new ideas and culture thus promoting intercultural education. It aims to study and examine the role of intercultural education in shifting and establishing new paradigms of education.

Keywords: education, intercultural, interpersonal, traditions, understanding

Procedia PDF Downloads 74

Authors: J. Alvarez, J. Pimienta, R. Sarmiento

Abstract:

Diode lasers working in free mode present different shifting and broadening determined by external factors such as temperature, current or mechanical vibrations, and they are not more useful in applications such as spectroscopy, metrology, and cooling of atoms, among others. Different configurations can reduce the spectral width of a laser; one of the most effective is to extend the optical resonator of the laser diode and use optical feedback either with the help of a partially reflective mirror or with a diffraction grating; this latter configuration is not only allowed to reduce the spectral width of the laser line but also to coarsely adjust its working wavelength, within a wide range typically ~ 10nm by slightly varying the angle of the diffraction grating. Two settings are commonly used for this purpose, the Littrow configuration and the Littmann Metcalf. In this paper, we present the design, construction, and characterization of a compact extended laser cavity in Littrow configuration. The designed cavity is compact and was machined on an aluminum block using computer numerical control (CNC); it has a mass of only 380 g. The design was tested on laser diodes with different wavelengths, 650nm, 780nm, and 795 nm, but can be equally efficient at other wavelengths. This report details the results obtained from the extended cavity working at a wavelength of 780 nm, with an output power of around 35mW and a line width of less than 1Mhz. The cavity was used to observe the spectrum of the corresponding Rubidium D2 line. By modulating the current and with the help of phase detection techniques, a dispersion signal with an excellent signal-to-noise ratio was generated that allowed the stabilization of the laser to a transition of the hyperfine structure of Rubidium with an integral proportional controller (PI) circuit made with precision operational amplifiers.

Keywords: Littrow, Littman-Metcalf, line width, laser stabilization, hyperfine structure

Procedia PDF Downloads 221

Authors: Nada Mouchfiq, Ahmed Habbani, Chaimae Benjbara

Abstract:

The security aspect of the IoT occupies a place of great importance especially after the evolution that has known this field lastly because it must take into account the transformations and the new applications .Blockchain is a new technology dedicated to the data sharing. However, this does not work the same way in the different systems with different operating principles. This article will discuss network security using the Blockchain to facilitate the sending of messages and information, enabling the use of new processes and enabling autonomous coordination of devices. To do this, we will discuss proposed solutions to ensure a high level of security in these networks in the work of other researchers. Finally, our article will propose a method of security more adapted to our needs as a team working in the ad hoc networks, this method is based on the principle of the Blockchain and that we named ”MPR Blockchain”.

Keywords: Ad hocs networks, blockchain, MPR, security

Procedia PDF Downloads 177

Authors: Elisabete Alberdi, Irantzu Álvarez, Laura Girón

Abstract:

The objective of this work is to propose a cycle path or network of paths to the UPV/EHU Campus in Leioa. The proposal will be presented from the point of view of sustainability. In order to achieve this, the roads that are already built will be used, and the road or network will be proposed to be built with the least amount of money possible. To select the most suitable route for the bike lane, various sources of information have been used. Through this data, we analyse the transport infrastructure and the mobility around the UPV/EHU Campus in Leioa. This work aims to satisfy the mobility needs of users on the University Campus to contribute to the sustainability of the campus.

Keywords: cycle lane, sustainability, accessibility, transport, agenda 2030

Procedia PDF Downloads 221

Authors: Leticia Lengler, Vania Estivalete, Vivian Flores Costa, Tais De Andrade, Lisiane Fellini Faller

Abstract:

Social entrepreneurship has emerged and driven a new development perspective, and as the literature mentions, it is based on innovation, and mainly, on the creation of social value, rather than personal wealth and shareholders. In this field of study, one of the focuses of discussion refers to the distinct characteristics of the individuals responsible for socially directed initiatives, named as social entrepreneurs. To contribute to this perspective, the present study aims to identify the values related to work that guide the performance of social entrepreneurs, members of enterprises that have developed themselves within a social incubator at a federal institution of higher education in Brazil. Each person's value system is present in different facets of his life, manifesting himself in his choices and in the way he conducts the relationship with other people in society. Especially the values of work, the focus of this research, play a significant role in organizational studies, since they are considered one of the important guiding principles of the behavior of individuals in the work environment. Regarding the method of the study, a descriptive and qualitative research was carried out. In the data collection, 24 entrepreneurs, members of five different enterprises belonging to the social incubator, were interviewed. The research instrument consisted of three open questions, which could be answered with the support of a "disc of values", an artifact organized to clearly demonstrate the values of the work to the respondents. The analysis of the interviews took into account the categories defined a priori, based on the model proposed by previous authors who validated these constructs within their research contexts, contemplating the following dimensions: Self-determination and stimulation; Safety; Conformity; Universalism and benevolence; Achievement; and Power. It should be noted that, in order to provide a better understanding of the interviewees, in the "disc of values" used in the research, these dimensions were represented by the objectives that define them, being respectively: Challenge; Financial independence; Commitment; Welfare of others; Personal success; And Power. Some preliminary results show that, as guiding principles of the investigation, priority is given to work values related to Self-determination and stimulation, Conformity and Universalism and benevolence. Such findings point to the importance given by these individuals to independent thinking and acting, as well as to novelty and constant challenge. Still, they demonstrate the appreciation of commitment to their enterprise, the people who make it and the quality of their work. They also point to the relevance of the possibility of contributing to the greater social good, that is, of the search for the well-being of close people and of society, as it is implied in models of social entrepreneurship coming from literature. With a lower degree of priority, the values denominated Safety and Realization, as the financial question at work and the search for satisfaction and personal success, through the use of socially recognized skills were mentioned aspects with little emphasis by social entrepreneurs. The Power value was not considered as guiding principle of the work for the respondents.

Keywords: qualitative study, social entrepreneur, social incubator, values of work

Procedia PDF Downloads 254

Authors: Veronica Ramirez

Abstract:

For over 40 years now, the Philippines has been supplying Household Service Workers (HSWs) globally. As a requirement of the Philippine Overseas Employment Agency (POEA), all Filipinos applying for overseas work undergo medical examination and a certificate of good health is submitted to the foreign employer before hiring. However, there are workplace-related health problems that develop during employment such as musculoskeletal strain or injury, back pain, hypertension and other illnesses. Some workers are in good working conditions but are on call more than 12 hours per day. There are also those who experience heavy physical work with short rest periods or time off. They can also be easily exposed to disease outbreaks and epidemics. It was the objective of this study to determine the common health problems of Filipino Overseas Service Workers and analyze their implications to wellness in the workplace. Specifically, it sought to describe the work conditions of HSWs and determine the work-related factors affecting their health. It also identified the medical care they avail of and how they perceive their health and wellness as determinants of well-being. Finally, it proposes ways to promote wellness among HSWs. This study focused on physical illnesses and does not include mental problems experienced by HSWs. Using a questionnaire, primary data were gathered online and through survey of HSW rehires who were retaking Pre-Departure Orientation Seminar at recruitment agencies. The 2010 Health Benefit Availment data from the Overseas Workers Welfare Administration (OWWA) was also utilized. Descriptive analysis was employed on the data gathered. Key stakeholders in the migration industry were also interviewed. Previous research studies, reports and literature on migration and wellness were used as secondary data. The study found that Filipino overseas HSWs are vulnerable to physical injury and experience body pains such as back, hip and shoulder pain. Long hours of work, work hazards and lack of rest due to poor accommodations can aggravate their physical condition. Although health insurance and health care are available, HSWs are not aware how to avail them. On the basis of the findings, a Wellness Program can be designed that include health awareness, health care availment, occupational ergonomics, safety and health, work and leisure balance, developing emotional intelligence, anger management and spirituality.

Keywords: health, household service worker, overseas, wellness

Procedia PDF Downloads 253

Authors: Endalew Fufa Kufi

Abstract:

Every married person aspires to be a parent regardless of the situation in which s/he lives. Such aspiration meets with reality when the destined parent is able to give adequate supports and services to his/her children, whether the latter are got by birth or through adoption. The adequacy of services parents provide their children is both enriched and tempted by the work on which they involve. On the one hand, parents need to work and earn a living in order to support their family. On the other hand, they must spend most of their time outside home to do the work, which shortens the time and might they spare to care for their children. Where the sufficiency of services parents owe their children could be ascertained by in terms of life skills, physical care and related provisions, the role of working fathers and mothers in providing such supports could be diverse across cultures and work traditions. Hence, this research deals with the investigation of working mothers’ parental practices, challenges they face in providing parental services and the implication for the future progress of the parents and their children. Target of the study will be Arsi University in Oromia Regional State of Ethiopia. Descriptive survey design in holding the research, and data for the research will be collected in the form of experiential self-report from 150 working mothers selected from the entire working women population of Colleges of Agriculture and Environmental Studies and College of Health Sciences through stratified random-sampling. Instruments of data collection will be closed and open-ended questionnaire. Complementary data will also be collected from purposively selected samples through semi-structured interview. Data for the research will be collected through questionnaire first and then through interview. Data analysis will also follow the same procedure. The collected data will systematically be organized and statistically and thematically analyzed in order to come up with indicative findings. The overarching thesis is that, working mothers in the study area bear a lot of responsibilities both at home and at work place which leave them very little time for parenting services. Unless due attention is given to the way they can spare time for their children, they are more likely to be tense between work-life and family care services, which tempt them in different directions.

Keywords: challenges, mothers, practices, university, working

Procedia PDF Downloads 294

Authors: K. N. Dinesh Babu

Abstract:

In this paper, the protection of a complicated bus arrangement with a dual bus coupler and bus sectionalizer using low impedance differential protection applicable for very high voltages like 220kV and 400kV is discussed. In many power generation stations, several operational procedures are implemented to utilize the transfer bus as the main bus and to facilitate the maintenance of circuit breakers and current transformers (in each section) without shutting down the bay(s). Owing to this fact, the complications in operational philosophy have thrown challenges for the bus bar protection implementation. Many bus topologies allow any one of the main buses available in the station to be used as an auxiliary bus. In such a system, pre-defined precautions and procedures are made as guidelines, which are followed before assigning any bus as an auxiliary bus. The procedure involves shifting of links, changing rotary switches, insertion of test block, and so on, thereby causing unreliable operation. This kind of unreliable operation or inadvertent procedural lapse may result in the isolation of the bus bar from the grid due to the unpredictable operation of the bus bar protection relay, which is a commonly occurring phenomenon due to manual mistakes. With the sophisticated configuration and implementation of logic in modern intelligent electronic devices, the operator is free to select the transfer arrangement without sacrificing the protection required by a bus differential system for a reliable operation, and labor-intensive processes are completely eliminated. This paper deals with the procedure to test the security logic for such special scenarios using Megger make SMRT, bus bar protection relay to assure system stability and get rid of all the specific operational precautions/procedure.

Keywords: bus bar protection, by-pass isolator, blind spot, breaker failure, intelligent electronic device, end fault, bus unification, directional principle, zones of protection, breaker re-trip, under voltage security, smart megger relay tester

Procedia PDF Downloads 63

Authors: Azaz Zaman, Mirazur Rahman

Abstract:

Capital market is a crucial financial market place where companies and the government can raise long-term funds and, at the same time, investors get the opportunity to invest in the listed companies. Capital markets play a vital role not only in shifting the funds from surplus entity to deficit for investment, but also in the overall economic development of any developing country like Bangladesh. Being the first and biggest capital market of Bangladesh, Dhaka Stock Exchange (DSE) is the prime bourse of the country. The differences in the investment preference— among three broad categories of investors in DSE including individual investors, institutional investors, and government— are easily observed. Authors of this article have used five categories of investors such as sponsors or directors of the company, institutional investors, foreign investors, government, and the general public in order to present a comparative analysis of their investment patterns. Obtaining data on the percentage of investment by these five types of investors in different sectors from the DSE website, this study aims to analyze the sector-wise investment preference of these investors using August 2018 data. The study has found that the sponsors or directors of the company have the highest percentage of investment in the textile industry which is close to 16%. The Bangladesh government, as an investor, has the highest percentage of investment in the fuel & power sector, approximately 32%. It has also found that the mutual funds' sector is mostly financed by institutional investors, nearly 28%. Foreign investors have their most investments in the banking sector, which is close to 22%. It has also revealed that the textile sector is mostly financed by the general public, close to 17%. Nevertheless, general public, surprisingly, has the lowest percentage of investment in the telecommunication sector, which is 0.10%.

Keywords: stock market investment, Dhaka stock exchange, capital market, Bangladesh

Procedia PDF Downloads 113

Authors: Eduardo Jorge Cabral dos Santos Fernandes

Abstract:

The expression ‘Porto School’, usually associated with an educational institution, the School of Fine Arts of Porto, is applied for the first time with the sense of an architectural trend by Nuno Portas in a text published in 1983. The expression is used to characterize a set of works by Porto architects, in which common elements are found, namely the desire to reuse languages and forms of the German and Dutch rationalism of the twenties, using the work of Alvar Aalto as a mediation for the reinterpretation of these models. In the same year, Álvaro Siza classifies the Finnish architect as a miscegenation agent who transforms experienced models and introduces them to different realities in a text published in Jornal de Letras, Artes e Ideias. The influence of foreign models and their adaptation to the context has been a recurrent theme in Portuguese architecture, which finds important contributions in the writings of Alexandre Alves Costa, at this time. However, the identification of these characteristics in Siza’s work is not limited to the Portuguese theoretical production: it is the recognition of this attitude towards the context that leads Kenneth Frampton to include Siza in the restricted group of architects who embody Critical Regionalism (in his book Modern architecture: a critical history). For Frampton, his work focuses on the territory and on the consequences of the intervention in the context, viewing architecture as a tectonic fact rather than a series of scenographic episodes and emphasizing site-specific aspects (topography, light, climate). Therefore, the motto of this paper is the dichotomous opposition between foreign influences and adaptation to the context in the early work of Álvaro Siza (designed in the sixties) in which the influence (theoretical, methodological, and formal) of Alvar Aalto manifests itself in the form and the language: the pool at Quinta da Conceição, the Seaside Pools and the Tea House (three works in Leça da Palmeira) and the Lordelo Cooperative (in Porto). This work is part of a more comprehensive project, which considers several case studies throughout the Portuguese architect's vast career, built in Portugal and abroad, in order to obtain a holistic view.

Keywords: Alvar Aalto, Álvaro Siza, foreign influences, adaptation to the context

Procedia PDF Downloads 23

Authors: Hadjer Chellia

Abstract:

The study explores the phenomenon of second language use in a migratory setting and uses the case of Algerian international students in Scotland, United Kingdom. The linguistic history of Algeria reveals that French language has a high status among the Algerians’ verbal repertoires and Algerian English students consider it as a language of prestige. With mobility of some of these students towards Scotland -in the guise of internationalization of higher education, mobility and exchange programs, the transition was deemed to bring more complexity to their pre-migratory linguistic repertoires and resulted into their French language- being endangered and threatened by a potential shift to English. The study employed semi-structured interviews among six Ph.D. ethnically related students, and the main aim behind that is to explore their current experiences with regards to French language use and to provide an account of the factors which assist in shifting to English as a second language instead. The six participants identified in interviews were further invited to focus group sessions based on an in-group interaction fashion to discuss different topics using heritage languages. This latter was opted for as part of the methodology as a means to observe their real linguistic practice and to investigate the link between behaviors and previous perceptions. The findings detect a variety of social, individual and socio-psychological factors that would contribute in refining the concept of language shift among newly established émigré communities with short stay vis a vis the linguistic outcomes of immigrants with long stay, across generational basis that was –to some extent-the focus of previous research on language shift. The results further reveal a mismatch between students' perceptions and observed behaviors. The research is then largely relevant to international students’ sociolinguistic experience of study abroad.

Keywords: complexity, mobility, potential shift, sociolinguistic experience

Procedia PDF Downloads 160

Authors: Rajan Deglurkar

Abstract:

The research carried out in this piece of work is on 'Framework of Sustainable Manufacturing for Small and Medium Enterprises'. It consists of elucidation of concepts about sustainable manufacturing and sustainable product development with critical review performed on seven techniques of sustainable manufacturing. The work also covers the survey about critical review of awareness in the market with respect to the manufacturers and the consumers. The factors and challenges for sustainable manufacturing implementation are reviewed and simple framework is constructed for the small and medium enterprise for successful implementation of sustainable manufacturing and sustainable product.

Keywords: sustainable development, sustainable manufacturing, resource efficiency, framework for sustainable manufacturing

Procedia PDF Downloads 509

Authors: Hasna Soli

Abstract:

The main objective of this work is the extraction of sulfur from gypsum here is industrial waste. Indeed the sulfuric acid production, passing through the following process; melting sulfur, filtration of the liquid sulfur, sulfur combustion to produce SO₂, conversion of SO₂ to SO₃ and SO₃ absorption in water to produce H₂SO₄ product as waste CaSO₄ the anhydrous calcium sulfate. The main objectives of this work are improving the industrial practices and to find other ways to manage these solid wastes. It should also assess the consequences of treatment in terms of training and become byproducts. Firstly there will be a characterization of this type of waste by an X-ray diffraction; to obtain phase solid compositions and chemical analysis; gravimetrically and atomic absorption spectrometry or by ICP. The samples are mineralized in suitable acidic or basic solutions. The elements analyzed are CaO, Sulfide (SO₃), Al₂O₃, Fe₂O₃, MgO, SiO₂. Then an analysis by EDS energy dispersive spectrometry using an Oxford EDX probe and differential thermal and gravimetric analyzes. Gypsum’s valuation will be performed. Indeed, the CaSO₄ will be reused to produce sulfuric acid, which will be reintroduced into the production line. The second approach explored in this work is the thermal utilization of solid waste to remove sulfur as a dilute sulfuric acid solution.

Keywords: environment, gypsum, sulfur, waste

Procedia PDF Downloads 287

Authors: C. Vogeler

Abstract:

Change processes such as individualization and digitalization have an impact on higher education. Graduates are expected to cooperate in creative work processes in their professional life. During their studies, they need to be prepared accordingly. This includes modern learning scenarios that integrate the benefits of digital media. Therefore, design thinking and blended learning have been combined in the project-based seminar conception introduced here. The presented seminar conception has been realized and evaluated with students of information sciences since September 2017. Within the seminar, the students learn to work on a project. They apply the methods in a problem-based learning scenario. Task of the case study is to arrange a conference on the topic gaming in libraries. In order to collaborative develop creative possibilities of realization within the group of students the design thinking method has been chosen. Design thinking is a method, used to create user-centric, problem-solving and need-driven innovation through creative collaboration in multidisciplinary teams. Central characteristics are the openness of this approach to work results and the visualization of ideas. This approach is now also accepted in the field of higher education. Especially in problem-based learning scenarios, the method offers clearly defined process steps for creative ideas and their realization. The creative process can be supported by digital media, such as search engines and tools for the documentation of brainstorming, creation of mind maps, project management etc. Because the students have to do two-thirds of the workload in their private study, design thinking has been combined with a blended learning approach. This supports students’ preparation and follow-up of the joint work in workshops (flipped classroom scenario) as well as the communication and collaboration during the entire project work phase. For this purpose, learning materials are provided on a Moodle-based learning platform as well as various tools that supported the design thinking process as described above. In this paper, the seminar conception with a combination of design thinking and blended learning is described and the potentials and limitations of the chosen strategy for the development of a course with a multimedia approach in higher education are reflected.

Keywords: blended learning, design thinking, digital media tools and methods, flipped classroom

Procedia PDF Downloads 193

Authors: Sunil Dutta

Abstract:

Synchronization is defined as ‘the sequencing and re-sequencing of all relative and absolute activities in time and space and continuous alignment of those actions with purposeful objective in a complex and dynamic atmosphere. In a complex and dynamic production / maintenance setup, no single group can work in isolation for long. In addition, many activities in projects take place simultaneously at the same time. Work of every section / group is interwoven with work of others. The various activities / interactions which take place in production / overhaul workshops are interlinked because of physical requirements (information, material, workforces, equipment, and space) and dependencies. The activity sequencing is determined by physical dependencies of various department / sections / units (e.g., inventory availability must be ensured before stripping and disassembling of equipment), whereas resource dependencies do not. Theory of constraint facilitates identification, analyses and exploitation of the constraint in methodical manner. These constraints (equipment, manpower, policies etc.) prevent the department / sections / units from getting optimum exploitation of available resources. The significance of theory of constraints for achieving synchronization at overhaul workshop is illustrated in this paper.

Keywords: synchronization, overhaul, throughput, obsolescence, uncertainty

Procedia PDF Downloads 345

Authors: Monique Somma

Abstract:

As special education service delivery models are shifting in order to better meet the academic and social rights of students with exceptionalities, teaching practices must also align with these goals. This phenomenological case study explored the change experiences of special education teachers who have transitioned from teaching in a self-contained special education class to an inclusive class setting. Ten special educators who had recently changed their teaching roles to inclusive classrooms, completed surveys and participated in a focus group. Of the original ten educators, five chose to participate further in individual interviews. Data collected from the three methods was examined and compared for common themes. Emergent themes included, support and training, attitudes and perceptions, inclusive practice, growth and change, and teaching practice. The overall findings indicated that despite their special education training, these educators were challenged by their own beliefs and expectations, the attitudes of others and systematic barriers in the education system. They were equally surprised by the overall social and academic performance of students with exceptionalities in inclusive classes, as well as, the social and academic growth and development of the other students in the class. Over the course of their careers, they all identified an overall personal pedagogical shift, to some degree or another, which they contributed to the successful experiences of inclusion they had. They also recognized that collaborating with others was essential for inclusion to be successful. The findings from this study suggest several implications for professional development and training needs specific to special education teachers moving into inclusive settings. Maximizing the skills of teachers with special education experience in a Professional Learning Community (PLC) and mentorship opportunities would be beneficial to all staffs working toward creating inclusive classrooms and schools.

Keywords: attitudes and perceptions, inclusion of students with exceptionalities, special education teachers, teacher change

Procedia PDF Downloads 228

Authors: Admire Isaac Tichafa Shayanowako, Mark Laing, Hussein Shimelis

Abstract:

Striga asiatica is among the leading abiotic constraints to maize production under small-holder farming communities in southern African. However, confirmed sources of resistance to the parasitic weed are still limited. Conventional breeding programmes have been progressing slowly due to the complex nature of the inheritance of Striga resistance, hence there is a need for more innovative approaches. This study aimed to achieve partial resistance as well as to breed for compatibility with Fusarium oxysporum fsp strigae, a soil fungus that is highly specific in its pathogenicity. The agar gel and paper roll assays in conjunction with a glass house pot trial were done to select genotypes based on their potential to stimulate germination of Striga and to test the efficacy of Fusarium oxysporum as a biocontrol agent. Results from agar gel assays showed a moderate to high potential in the release of Strigalactones among the 33 OPVs. Maximum Striga germination distances from the host root of 1.38 cm and up to 46% germination were observed in most of the populations. Considerable resistance was observed in a landrace ‘8lines’ which had the least Striga germination percentage (19%) with a maximum distance of 0.93 cm compared to the resistant check Z-DPLO-DTC1 that had 23% germination at a distance of 1.4cm. The number of fusarium colony forming units significantly deferred (P < 0.05) amongst the genotypes growing between germination papers. The number of crown roots, length of primary root and fresh weight of shoot and roots were highly correlated with concentration of fusarium macrospore counts. Pot trials showed significant differences between the fusarium coated and the uncoated treatments in terms of plant height, leaf counts, anthesis-silks intervals, Striga counts, Striga damage rating and Striga vigour. Striga emergence counts and Striga flowers were low in fusarium treated pots. Plants in fusarium treated pots had non-significant differences in height with the control treatment. This suggests that foxy 2 reduces the impact of Striga damage severity. Variability within fusarium treated genotypes with respect to traits under evaluation indicates the varying degree of compatibility with the biocontrol.

Keywords: maize, Striga asiaitca, resistance, compatibility, F. oxysporum

Procedia PDF Downloads 242

Authors: Ilme Faridatul, Bo Wu

Abstract:

Bangladesh is often called as a motherland of rivers. It contains about 700 rivers among all these the Padma River is one of the largest rivers of Bangladesh. The change of river bank and erosion has become a common environmental natural hazard in Bangladesh. The river banks are under intense pressure from natural processes such as erosion and accretion as well as anthropogenic processes such as urban growth and pollution. The Padma River is flowing along ten districts of Bangladesh among all these Faridpur district is most vulnerable to river bank erosion. The severity of the river erosion is so high that each year a thousand of populations become homeless and lose their agricultural lands. Though the Faridpur district is most vulnerable to river bank erosion no specific research has been conducted to identify the changing pattern of river bank along this district. The outcome of the research may serve as guidance to prepare river bank monitoring program and management. This research has utilized integrated techniques of remote sensing and geographic information system to monitor the changes from 1995 to 2015 at Faridpur district. To discriminate the land water interface Modified Normalized Difference Water Index (MNDWI) algorithm is applied and on screen digitization approach is used over MNDWI images of 1995, 2002 and 2015 for river bank line extraction. The extent of changes in the river bank along Faridpur district is estimated through overlaying the digitized maps of all three years. The river bank lines are highlighted to infer the erosion and accretion and the changes are calculated. The result shows that the middle of the river is gaining land through sedimentation and the both side river bank is shifting causing severe erosion that consequently resulting the loss of farmland and homestead. Over the study period from 1995 to 2015 it witnessed huge erosion and accretion that played an active role in the changes of the river bank.

Keywords: river bank, erosion and accretion, change monitoring, remote sensing

Procedia PDF Downloads 318

Authors: Amol M. Jadhav, Sharad S. Chudhari, S. S. Khedkar

Abstract:

This review presents a through survey of research paper work on the experimental analysis, FEM Analysis & simulation of the metal spinning process. In this literature survey all the papers being taken from Elsevier publication and most of the from journal of material processing technology. In a last two decade or so, metal spinning process gradually used as chip less formation for the production of engineering component in a small to medium batch quantities. The review aims to provide include into the experimentation, FEM analysis of various components, simulation of metal spinning process and act as guide for research working on metal spinning processes. The review of existing work has several gaps in current knowledge of metal spinning processes. The evaluation of experiment is thickness strain, the spinning force, the twisting angle, the surface roughness of the conventional & shear metal spinning process; the evaluation of FEM of metal spinning to path definition with sufficient fine mesh to capture behavior of work piece; The evaluation of feed rate of roller, direction of roller,& type of roller stimulated. The metal spinning process has the more flexible to produce a wider range of product shape & to form more challenge material.

Keywords: metal spinning, FEM analysis, simulation of metal spinning, mechanical engineering

Procedia PDF Downloads 384

Authors: Monika Szpringer, Mariola Wojciechowska, Robert Dutkiewicz, Grażyna Nowak-Starz, Marzena Olędzka

Abstract:

The main aim of this article is to determine the phenomenon of stress among academic teachers as well as to identify the extent to which the teachers experience work-related psychological risks. It is also important to support academic teachers trade unions in scope of stress-oriented activities, including psychological dangers in the assessment of risk in the workplace (college). The authors used a method of a diagnostic survey with a polling as a technique and authors’ questionnaire as a tool. The survey was conducted between September and December of 2013 and it comprised 1890 academic teachers from five voivodeships. The study reveals that 84.0% of the respondents found the work of an academic teacher to be borne with a considerable stress. The percentage values of the most frequent causes of stress are as follows: frequent changes of both organisational and didactic matters as well as overwhelming bureaucracy (77.8 %), time pressure regarding professional development and related risk of losing job (68.2 %), difficult working conditions (45.4%), conflicts and rivalry between teachers (44.1%), excessive amount of duties as well as increasing requirements and demanding attitude of students (33.7%). Work-related stress affects or significantly affects the private life of 69 % and 66.4 % of the respondents respectively. The majority of the people surveyed deals with stress by undertaking various activities, with 40% pointing at using various substances, mostly cigarettes and alcohol (p > 0,05) Physical ailments were experienced by 81% of the respondents, in 9% they were rare and 8 % of the respondents had never experienced such disorders. The entire group of the surveyed people (100 %) claimed that they have no possibility of contacting a psychologist at their workplace (p > 0.05), and they stated that the need of contacting specialists does exist.

Keywords: stress, academic teachers, psychological risks, work-related

Procedia PDF Downloads 389

Authors: Ignatio Madanhire, Charles Mbohwa

Abstract:

This study explores to improve the resource efficiency, waste water reduction and to reduce losses of raw materials in a beverage making industry. A number of cleaner production technologies were put across in this work. It was also noted that cleaner production technology practices are not only desirable from the environmental point of view, but they also make good economic sense, in their contribution to the bottom line by conserving resources like energy, raw materials and manpower, improving yield as well as reducing treatment/disposal costs. This work is a resource in promoting adoption and implementation of CP in other industries for sustainable development.

Keywords: resource efficiency, beverages, reduce losses, cleaner production, energy, yield

Procedia PDF Downloads 410

Authors: Zaidour Mohamed, Ghalem Ali Jr., Achit Henni Mohamed

Abstract:

This project is destined to study pole junctions of reinforced concrete beams subjected to seismic loads. A literature review was made to clarify the work done by researchers in the last three decades and especially the results of the last two years that were studied for the determination of the method of calculating the transverse reinforcement in the different nodes of a structure. For implementation efforts in the columns and beams of a building R + 4 in zone 3 were calculated using the finite element method through software. These results are the basis of our work which led to the calculation of the transverse reinforcement of the nodes of the structure in question.

Keywords: beam–column joints, cyclic loading, shearing force, damaged joint

Procedia PDF Downloads 543