Search results for: computer operating principle

Authors: Xin-Yu Shih, Yue-Qu Liu, Hong-Ru Chou

Abstract:

This paper presents a low-area and fully-reconfigurable Fast Fourier Transform (FFT) hardware design for 3GPP-LTE communication standard. It can fully support 32 different FFT sizes, up to 2048 FFT points. Besides, a special processing element is developed for making reconfigurable computing characteristics possible, while first-in first-out (FIFO) scheduling scheme design technique is proposed for hardware-friendly FIFO resource arranging. In a synthesis chip realization via TSMC 40 nm CMOS technology, the hardware circuit only occupies core area of 0.2325 mm² and dissipates 233.5 mW at maximal operating frequency of 250 MHz.

Keywords: reconfigurable, fast Fourier transform (FFT), single-path delay feedback (SDF), 3GPP-LTE

Procedia PDF Downloads 278

Authors: Rashid Ahmed , John N. Avaritsiotis

Abstract:

Many signal subspace-based approaches have already been proposed for determining the fixed Direction of Arrival (DOA) of plane waves impinging on an array of sensors. Two procedures for DOA estimation based neural networks are presented. First, Principal Component Analysis (PCA) is employed to extract the maximum eigenvalue and eigenvector from signal subspace to estimate DOA. Second, minor component analysis (MCA) is a statistical method of extracting the eigenvector associated with the smallest eigenvalue of the covariance matrix. In this paper, we will modify a Minor Component Analysis (MCA(R)) learning algorithm to enhance the convergence, where a convergence is essential for MCA algorithm towards practical applications. The learning rate parameter is also presented, which ensures fast convergence of the algorithm, because it has direct effect on the convergence of the weight vector and the error level is affected by this value. MCA is performed to determine the estimated DOA. Preliminary results will be furnished to illustrate the convergences results achieved.

Keywords: Direction of Arrival, neural networks, Principle Component Analysis, Minor Component Analysis

Procedia PDF Downloads 451

Authors: Mohamed Gar Alalm

Abstract:

This study aims to investigate various operating conditions that affect the performance of the electro-Fenton process for degradation of pesticides. Stainless steel electrodes were utilized in the electro-Fenton cell due to their relatively low cost. The favored conditions of current intensity, pH, iron loading, and pesticide concentration were deeply discussed. Complete removal of pesticide was attained at the optimum conditions. The degradation kinetics were described by pseudo- first-order pattern. In addition, a response surface model was developed to describe the performance of electro-Fenton process under different operational conditions. The model indicated that the coefficient of determination was (R² = 0.995).

Keywords: electro-Fenton, stainless steel, pesticide, wastewater

Procedia PDF Downloads 141

Authors: Youssef Abdelli, Rachid Nasri

Abstract:

The large amplitude free vibration analysis of three-layered symmetric sandwich beams is carried out using two different approaches. The governing nonlinear partial differential equations of motion in free natural vibration are derived using Hamilton's principle. The formulation leads to two nonlinear partial differential equations that are coupled both in axial and binding deformations. In the first approach, the method of multiple scales is applied directly to the governing equation that is a nonlinear partial differential equation. In the second approach, we discretize the governing equation by using Galerkin's procedure and then apply the shooting method to the obtained ordinary differential equations. In order to check the validity of the solutions obtained by the two approaches, they are compared with the solutions obtained by two approaches; they are compared with the solutions obtained numerically by the finite difference method.

Keywords: finite difference method, large amplitude vibration, multiple scales, nonlinear vibration

Procedia PDF Downloads 463

Authors: Shaik Jilani Basha, Inavolu Avinash, Alla Venu Sai Reddy, Bitragunta Taraka Ramu

Abstract:

We can use the neural style transfer technique to build a picture with the same "content" as the beginning image but the "style" of the picture we've chosen. Neural style transfer is a technique for merging the style of one image into another while retaining its original information. The only change is how the image is formatted to give it an additional artistic sense. The content image depicts the plan or drawing, as well as the colors of the drawing or paintings used to portray the style. It is a computer vision programme that learns and processes images through deep convolutional neural networks. To implement software, we used to train deep learning models with the train data, and whenever a user takes an image and a styled image, the output will be as the style gets transferred to the original image, and it will be shown as the output.

Keywords: neural networks, computer vision, deep learning, convolutional neural networks

Procedia PDF Downloads 95

Authors: Mohd Afif Md Nasir, Faizal Amin Nur Yunus, Jamaluddin Hashim, Abd Samad Hassan Basari, A. Halim Sahelan

Abstract:

The aim of this study is to identify the suitability of Virtual Learning Environment (VLE) in welding simulator application towards Computer-Based Training (CBT) in developing skills upon new students at the Advanced Technology Training Center (ADTEC), Batu Pahat, Johor, Malaysia and GIATMARA, Batu Pahat, Johor, Malaysia. The purpose of the study is to create a computer-based skills development approach in welding technology among new students in ADTEC and GIATMARA, as well as cultivating the elements of general skills among them. This study is also important in elevating the number of individual knowledge workers (K-workers) working in manufacturing industry in order to achieve a national vision which is to be an industrial nation in the year of 2020. The design of the study is a survey type of research which uses questionnaires as the instruments and 136 students from ADTEC and GIATMARA were interviewed. Descriptive analysis is used to identify the frequency and mean values. The findings of the study shows that the welding technology skills have developed in the students as a result of the application of VLE simulator at a high level and the respondents agreed that the skills could be embedded through the application of the VLE simulator. In summary, the VLE simulator is suitable in welding skills development training in terms of exposing new students with the relevant characteristics of welding skills and at the same time spurring the students’ interest towards learning more about the skills.

Keywords: computer-based training (CBT), knowledge workers (K-workers), virtual learning environment, welding simulator, welding technology

Procedia PDF Downloads 348

Authors: Risanda Alirastra Budiantoro, Riesanda Najmi Sasmita, Sri Herianingrum

Abstract:

Allah has given the guidance in the form of Islam for Muslim to take and lead all the aspects of life including the economic activity. The Islamic economic system is believed to be the answer to the economic problems that exist at this time. The goal is to achieve falah in kaffah by not doing some economic activities that are in violation as prescribed by Islam. An example for this is riba. Discourse on riba can be said ‘classical’ both in the development of Islamic thought and in Islamic civilization because riba often occurs in all aspects of public life, especially economic transactions (in Islam called muamalah). Riba is an additional retrieval, either in a sale and purchase transaction or lending in a false or contrary to the principle of muamalah in Islam. Prohibition of riba is obtained from various sources by the Qur'an and Hadith Rasulullah SAW, so the scholars firmly and clearly defined the prohibition of riba because there are exploitative elements that can harm the others. So, this study is aimed to identify Islamic economic system and the prohibition of riba in historical perspective. From the results of this study, it is expected to be a good reference for the reader to understand the Islamic economic system and riba in the future.

Keywords: economics system, riba, historical perspective, economy

Procedia PDF Downloads 318

Authors: Sneha Samal, Iva Petrikova, Bohdana Marvalova

Abstract:

Influence of grain size, shape and grain boundary diffusion at high temperature oxidation of pure metal is investigated as the function of microstructure evolution in this article. The oxidized scale depends on the geometrical parameter of the metal-scale system and grain shape, size, diffusion through boundary layers and influence of the contamination. The creation of the inner layer and the morphological structure develops from the internal stress generated during the growth of the scale. The oxidation rate depends on the cation and anion mobile transport of the metal in the inward and outward direction of the diffusion layer. Oxidation rate decreases with decreasing the grain size of the pure metal, whereas zinc deviates from this principle. A strong correlation between the surface roughness evolution, grain size, crystalline properties and oxidation mechanism of the oxidized metal was established.

Keywords: high temperature oxidation, pure metals, grain size, shape and grain boundary

Procedia PDF Downloads 497

Authors: Norhaslina Mat Zian, Hasril Hasini, Nur Irmawati Om

Abstract:

This study focuses on the flow and combustion behavior inside gas turbine combustor used in thermal power plant. The combustion process takes place using synthetic gas and the baseline solution was made on gas turbine combustor firing natural gas (100% Methane) as the main source of fuel. Attention is given to the effect of the H2/CO ratio on the variation of the flame profile, temperature distribution, and emissions. The H2/CO ratio varies in the range of 10-80 % and the CH4 values are fixed 10% for each case. While keeping constant the mass flow rate and operating pressure, the preliminary result shows that the flow inside the can-combustor is highly swirling which indicates good mixing of fuel and air prior to the entrance of the mixture to the main combustion zone.

Keywords: cfd, combustion, flame, syngas

Procedia PDF Downloads 284

Authors: Young-Kwan Choi, Han-Sang Jeong, Yeon-Ho Ok, Jae-Ho Choi

Abstract:

The purpose of this study is to verify validity of design by testing output of induction generator through finite element analysis before manufacture of induction generator designed. Characteristics in the operating domain of induction generator can be understood through analysis of magnetic field according to load (rotational speed) of induction generator. Characteristics of induction generator such as induced voltage, current, torque, magnetic flux density (magnetic flux saturation), and loss can be predicted by analysis of magnetic field.

Keywords: electromagnetic analysis, induction generator, small hydro power generator, small francis turbine generator

Procedia PDF Downloads 1475

Authors: E. Erdogan, H. A. Erdogan

Abstract:

FengShui, an old Chinese discipline, dates back to more than 5000 years, is one of the design principles that aim at creating habitable and sustainable spaces in harmony with nature by systematizing data within its own structure. Having emerged from Chinese mysticism and embodying elements of faith in its principles, FengShui argues that the positive energy in the environment channels human behavior and psychology. This argument is supported with the thesis of quantum physics that ‘everything is made up of energy’ and gains an important place. In spaces where living and working take place with several principles and systematized rules, FengShui promises a happier, more peaceful and comfortable life by influencing human psychology, acts, and soul as well as the professional and social life of the individual. Observing these design properties in houses, workplaces, offices, the environment, and daily life as a design paradigm is significant. In this study, how FengShui, a Central Asian culture emanated from Chinese mysticism, shapes design and how it is used as an element of sustainable design will be explained.

Keywords: Feng Shui, design principle, sustainability, philosophy

Procedia PDF Downloads 542

Authors: Cassandra Pratt Romero, Andres Gomez de Silva Garza

Abstract:

This paper describes a computational system designed to imitate human inspiration during musical composition. The system is called MIS (Musical Inspiration Simulator). The MIS system is inspired by media to which human beings are exposed daily (visual, textual, or auditory) to create new musical compositions based on the emotions detected in said media. After building the system we carried out a series of evaluations with volunteer users who used MIS to compose music based on images, texts, and audio files. The volunteers were asked to judge the harmoniousness and innovation in the system's compositions. An analysis of the results points to the difficulty of computational analysis of the characteristics of the media to which we are exposed daily, as human emotions have a subjective character. This observation will direct future improvements in the system.

Keywords: human inspiration, musical composition, musical composition by computer, theory of sensation and human perception

Procedia PDF Downloads 183

Authors: F. Rahimi Dehgolan, S. E. Khadem, S. Bab, M. Najafee

Abstract:

Nowadays, using rotating systems like shafts and disks in industrial machines have been increased constantly. Dynamic stability is one of the most important factors in designing rotating systems. In this study, linear frequencies and stability of a coupled continuous flexible rotor-disk-blades system are studied. The Euler-Bernoulli beam theory is utilized to model the blade and shaft. The equations of motion are extracted using the extended Hamilton principle. The equations of motion have been simplified using the Coleman and complex transformations method. The natural frequencies of the linear part of the system are extracted, and the effects of various system parameters on the natural frequencies and decay rates (stability condition) are clarified. It can be seen that the centrifugal stiffening effect applied to the blades is the most important parameter for stability of the considered rotating system. This result highlights the importance of considering this stiffing effect in blades equation.

Keywords: rotating shaft, flexible blades, centrifugal stiffness, stability

Procedia PDF Downloads 265

Authors: Fotis Vouzas

Abstract:

This paper is an attempt to investigate the Business Ethics link to Quality Management. Business Ethics as a management practice is well rooted in many organizations, but its contribution to quality management implementation programs and practices is not well documented. The ISO 9000 and the Business Excellence frameworks and Awards seem to provide a basis for the implementation of a TQM philosophy contributing to efficiency, enhanced performance and sustainability. The author examines a series of Corporate Ethics initiatives and investigates the relationship to Total Quality Management in an MNC operating in Greece. The data gathering was carried out through extensive and in-depth interviews with several multiple informants, i.e., the plant manager, the production manager, and the personnel manager, using a semi-structured questionnaire with open-ended questions.

Keywords: total quality management, business ethics, Greece, ISO 9000

Procedia PDF Downloads 77

Authors: Ksheeraj Sai Vepuri, Nada Attar

Abstract:

We as humans use words with accompanying visual and facial cues to communicate effectively. Classifying facial emotion using computer vision methodologies has been an active research area in the computer vision field. In this paper, we propose a simple method for facial expression recognition that enhances accuracy. We tested our method on the FER-2013 dataset that contains static images. Instead of using Histogram equalization to preprocess the dataset, we used Unsharp Mask to emphasize texture and details and sharpened the edges. We also used ImageDataGenerator from Keras library for data augmentation. Then we used Convolutional Neural Networks (CNN) model to classify the images into 7 different facial expressions, yielding an accuracy of 69.46% on the test set. Our results show that using image preprocessing such as the sharpening technique for a CNN model can improve the performance, even when the CNN model is relatively simple.

Keywords: facial expression recognittion, image preprocessing, deep learning, CNN

Procedia PDF Downloads 143

Authors: Tuleshova Gulnara, Abduldayeva Aigul

Abstract:

The goal is based on the studying the prevalence of micronutrient deficiencies among children and women of reproductive age to develop evidence-based recommendations aimed at improving the effectiveness of programs to prevent micronutrient deficiency. Subject: In our study we used a representative, random sample, carried out with the cluster method in the precinct of the principle areas of medical care for children 5 years of old. If the site has at least 60 children under 5 years of old, each second child was sampled, and if more than 60 children - each third child (first child selected by random sampling). The total number of investigated persons was within 80-86 women of reproductive age and children - within 80-92 people. Results: The studies found that the average prevalence of anemia among children aged 6-59 months was 35.2%, with the most susceptible to iron deficiency anemia in infants aged 6-23 months (53.3%). The prevalence of anemia among non-pregnant women was 39.0% among pregnant women - 43.8%. In children, the prevalence of folate deficiency was the highest (27.6%). Among non-pregnant women, frequent prevalence of folic acid deficiency was 37.0%. The prevalence of vitamin A deficiency was higher among children living in Astana (37.4%) compared with the medium-republican level (23.2%).

Keywords: nutrition, pregnant women, micronutrients, macronutrients

Procedia PDF Downloads 616

Authors: F. A. Gdhaidh, K. Hussain, H. S. Qi

Abstract:

A numerical study of natural convection heat transfer in water filled cavity has been examined in 3D for single phase liquid cooling system by using an array of parallel plate fins mounted to one wall of a cavity. The heat generated by a heat source represents a computer CPU with dimensions of 37.5×37.5 mm mounted on substrate. A cold plate is used as a heat sink installed on the opposite vertical end of the enclosure. The air flow inside the computer case is created by an exhaust fan. A turbulent air flow is assumed and k-ε model is applied. The fins are installed on the substrate to enhance the heat transfer. The applied power energy range used is between 15- 40W. In order to determine the thermal behaviour of the cooling system, the effect of the heat input and the number of the parallel plate fins are investigated. The results illustrate that as the fin number increases the maximum heat source temperature decreases. However, when the fin number increases to critical value the temperature start to increase due to the fins are too closely spaced and that cause the obstruction of water flow. The introduction of parallel plate fins reduces the maximum heat source temperature by 10% compared to the case without fins. The cooling system maintains the maximum chip temperature at 64.68℃ when the heat input was at 40 W which is much lower than the recommended computer chips limit temperature of no more than 85℃ and hence the performance of the CPU is enhanced.

Keywords: chips limit temperature, closed enclosure, natural convection, parallel plate, single phase liquid

Procedia PDF Downloads 265

Authors: Rishabh Ambavanekar

Abstract:

Expressive Aphasia (EA) is an oral disability, common among stroke victims, in which the Broca’s area of the brain is damaged, interfering with verbal communication abilities. EA currently has no technological solutions and its only current viable solutions are inefficient or only available to the affluent. This prompts the need for an affordable, innovative solution to facilitate recovery and assist in speech generation. This project proposes a novel concept: using a wearable low-cost electroencephalography (EEG) device-based brain-computer interface (BCI) to translate a user’s inner dialogue into words. A low-cost EEG device was developed and found to be 10 to 100 times less expensive than any current EEG device on the market. As part of the BCI, a machine learning (ML) model was developed and trained using the EEG data. Two stages of testing were conducted to analyze the effectiveness of the device: a proof-of-concept and a final solution test. The proof-of-concept test demonstrated an average accuracy of above 90% and the final solution test demonstrated an average accuracy of above 75%. These two successful tests were used as a basis to demonstrate the viability of BCI research in developing lower-cost verbal communication devices. Additionally, the device proved to not only enable users to verbally communicate but has the potential to also assist in accelerated recovery from the disorder.

Keywords: neurotechnology, brain-computer interface, neuroscience, human-machine interface, BCI, HMI, aphasia, verbal disability, stroke, low-cost, machine learning, ML, image recognition, EEG, signal analysis

Procedia PDF Downloads 119

Authors: Saadan Man, Razidah Othmanjaludin, Madiha Baharuddin

Abstract:

Nowadays, the pharmaceutical products are produced through the mixing of active and complex ingredient, naturally or synthetically; and involve extensive use of prohibited animal products. This article studies the challenges faced from fiqh perspective in the production of halal pharmaceutical products which frequently contain impure elements or prohibited animal derivatives according to Islamic law. This study is qualitative which adopts library research as well as field research by conducting series of interviews with the several related parties. The gathered data is analyzed from Sharia perspective by using some instruments especially the principle of Maqasid of Sharia. This study shows that the halal status of pharmaceutical products depends on the three basic elements: the sources of the basic ingredient; the processes involved in three phases of production, i.e., before, during and after; and the possible effects of the products. Various fiqh challenges need to be traversed in producing halal pharmaceutical products including the sources of the ingredients, the logistic process, the tools used, and the procedures of productions. Thus, the whole supply chain of production of pharmaceutical products must be well managed in accordance to the halal standard.

Keywords: fiqh, halal pharmaceutical, pharmaceutical products, Malaysia

Procedia PDF Downloads 192

Authors: Mahsa Pishdar

Abstract:

Food traceability through the supply chain is facing increased demand. IoT and blockchain are among the tools under consideration in the Industry 4.0 era that could be integrated to help implementation of the Circular Economy (CE) principles while enhancing food traceability solutions. However, such tools need intellectual system, and infrastructureto be settled as guidance through the way, helping overcoming obstacles. That is why the critical success factors for implementing Industry 4.0 and circular economy principles in food traceability concept are analyzed in this paper by combination of interval type 2 fuzzy Worst Best Method and Measurement Alternatives and Ranking according to Compromise Solution (Interval Type 2 fuzzy WBM-MARCOS). Results indicate that “Knowledge of Industry 4.0 obligations and CE principle” is the most important factor that is the basis of success following by “Management commitment and support”. This will assist decision makers to seize success in gaining a competitive advantage while reducing costs through the supply chain.

Keywords: food traceability, industry 4.0, internet of things, block chain, best worst method, marcos

Procedia PDF Downloads 205

Authors: Jamil Khalil Izraqi

Abstract:

This paper investigates the transition of a 1970 Volkswagen Beetle from an internal combustion engine (ICE) to an EV using Matlab/Simulink modeling and simulation. The performance of the EV drivetrain system was simulated under various operating conditions, including standard and custom driving cycles in Turkey and Jordan (Amman), respectively. The results of this paper indicate that the transition is viable and that modeling and simulation can help in understanding the performance and efficiency of the electric drivetrain system, including battery pack, power electronics, and brushless direct current (BLDC) Motor.

Keywords: BLDC, buck-boost, inverter, SOC, drive-cycle

Procedia PDF Downloads 101

Authors: A. Assif

Abstract:

This paper presents the modeling of a prototype distribution static compensator (D-STATCOM) for voltage sag and swell mitigation in an unbalanced distribution system. Here the concept that an inverter can be used as generalized impedance converter to realize either inductive or capacitive reactance has been used to mitigate power quality issues of distribution networks. The D-STATCOM is here supposed to replace the widely used StaticVar Compensator (SVC). The scheme is based on the Voltage Source Converter (VSC) principle. In this model PWM based control scheme has been implemented to control the electronic valves of VSC. Phase shift control Algorithm method is used for converter control. The D-STATCOM injects a current into the system to mitigate the voltage sags. In this paper the modeling of D¬STATCOM has been designed using MATLAB SIMULINIC. Accordingly, simulations are first carried out to illustrate the use of D-STATCOM in mitigating voltage sag in a distribution system. Simulation results prove that the D-STATCOM is capable of mitigating voltage sag as well as improving power quality of a system.

Keywords: D-STATCOM, voltage sag, voltage source converter (VSC), phase shift control

Procedia PDF Downloads 343

Authors: Jenny Lee

Abstract:

Fat Studies is emerging as an interdisciplinary area of study, intersecting with Gender Studies, Sociology, Human Development and the Creative Arts. A focus on weight loss, and, therefore, fat hatred, has resulted in a form of discriminatory institutional practice that impacts women in the Western world. This focus is sanctioned by a large dieting industry, medical associations, the media, and at times, government initiatives. This paper will discuss the emergence of the so-called ‘Obesity Epidemic’ in Australia and the Western world and the stereotypes that thin equals healthy and fat equals unhealthy. This paper will argue that, for those with a health focus, ‘Health at every size’ is a more effective principle, which involves striving for healthy living, without a focus on weight loss. This discussion will contextualise an autoethnographic exploration of how fat acceptance and Health at Every Size can be encouraged through fat activism and fat political art. As part of this paper, a selection of the recent performance, writing and art in Australia will be presented, including Aquaporko, the fat femme synchronised swim team and VaVaBoomBah, the Melbourne fat burlesque performances.

Keywords: activism, fat, health, obesity, performance

Procedia PDF Downloads 182

Authors: Dini Dewi Heniarti

Abstract:

In the past decades, Indonesia has suffered severe terrorist attacks, faced major terrorism challenges and has made impressive progress in countering it. The trend of terrorist groups operating in Indonesia is to focus on ‘soft’ targets. Indonesia has made notable progress in strengthening the legal regime against terrorism, in conformity with the international treaties against terrorism. Further measures are however needed to complete the legal regime building processes. This paper will demonstrate analyze socio yuridical contra and counter terrorism by Indonesia Government.

Keywords: policy, strategy, combatting terrorism, socio juridical, counter and contra terrorism

Procedia PDF Downloads 423

Authors: Lilian Kishimbo

Abstract:

This study aims to examine Corporate Social Responsibility (CSR) practices of local large firms of East Africa region. In this study CSR is defined as all actions that go beyond obeying minimum legal requirements as espoused by other authors. Despite the increase of CSR literature empirical evidence clearly demonstrate an imbalance of CSR studies in the developing countries . Moreover, it is evident that most of the research on CSR in developing economies emerges from large fast-growing economies or BRICS members (i.e. Brazil, India, China and South Africa), and Indonesia and Malaysia and a further call for more research in Africa is particularly advocated. Taking Africa as an example, there are scanty researches on CSR practices, and the few available studies are mainly from Nigeria and South Africa leaving other parts of Africa for example East Africa underrepresented. Furthermore, in the face of globalization, experience shows that literature has focused mostly on multinational companies (MNCs) operating in either North-North or North-South and less on South-South indigenous local firms. Thus the existing literature in Africa shows more studies of MNCs and little is known about CSR of local indigenous firms operating in the South particularly in the East Africa region. Accordingly, this paper explores CSR practices of indigenous local large firms of East Africa region particularly Kenya and Tanzania with the aim of testing the hypothesis that do local firms of East Africa region engage in similar CSR practices as firms in other parts of the world?. To answer this question only listed local large firms were considered based on the assumption that they are large enough to engage. Newspapers were the main source of data and information collected was supplemented by business Annual Reports for the period 2010-2012. The research finding revealed that local firms of East Africa engage in CSR practices. However, there are some differences in the set of activities these firms prefers to engage in compared to findings from previous studies. As such some CSR that were given priority by firms in East Africa were less prioritized in the other part of the world including Indonesia. This paper will add knowledge to the body of CSR and experience of CSR practices of South-South indigenous firms where is evidenced to have a relative dearth of literature on CSR. Finally, the paper concludes that local firms of East Africa region engage in similar activities like other firms globally. But firms give more priority to some activities such education and health related activities. Finally, the study intends to assist policy makers at firm’s levels to plan for long lasting projects related to CSR for their stakeholders.

Keywords: Africa, corporate social responsibility, developing countries, indigenous firms, Kenya, Tanzania

Procedia PDF Downloads 417

Authors: Aykut Bedük, Kemalettin Eryeşil, Osman Eşmen

Abstract:

The aim of this study is to examine the relationship between organizational commitment which is defined as a strong belief in and acceptance of the organization’s goals and values, and burnout syndrome and organizational cynicism. Accordingly, a field research based on survey method was conducted on the employees of a health institution operating in the province of Konya. The findings of the research show that there is a positive statistically significant relationship between organizational cynicism and burnout while there is a negative statistically significant relationship between organizational commitment and burnout. Furthermore, it has been also realized that there is a negative and statistically significant relationship between organizational commitment and organizational cynicism.

Keywords: burnout, organizational commitment, organizational cynicism, healthcare management

Procedia PDF Downloads 277

Authors: Susan Cardillo

Abstract:

This research will consider ways to bridge the gap between Computer Science and Media Communications and while doing so create Social Entrepreneurship for student success. New Media, as it has been referred to, is considered content available on-demand through Internet, a digital device, usually containing some kind of interactivity and creative participation. It is the interplay between technology, images, media and communications. The next generation of the newspaper, radio, television, and film students need to have a working knowledge of the technologies that are available for the creation of their work and taught to use this knowledge to create a voice. The work is interdisciplinary; in communications, we understand the necessity of reporting and disseminating information. In documentary film we understand the instructional and historic aspects of media and technology and in the non-profit sector, we see the need for expanding outlets for good. So, the true necessity is to utilize ‘new media’ technologies to advance social causes while reporting information, teaching and creating art. Goals: The goal of this research is to give communications students a better understanding of the technology that is both, currently at their disposal, and on the horizon, so that they can use it in their media, communications and art endeavors to be a voice for their generation. There is no longer a need to be a computer scientist to have a working knowledge of communication technologies and how they will benefit our work. There are many free and easy to use applications available for the creation of interactive communications. Methodology: This is Qualitative-Case Study that puts these ideas into action. There is a survey at the end of the experiment that is qualitative in nature and allows for the participants to share ideas and feelings about the technology and approach.

Keywords: interactive storytelling, web documentary, mass communications, teaching

Procedia PDF Downloads 280

Authors: Retno Supriyanti, Ahmad Chuzaeri, Yogi Ramadhani, A. Haris Budi Widodo

Abstract:

The use of ultrasonography in the medical world has been very popular including the diagnosis of pregnancy. In determining pregnancy, ultrasonography has many roles, such as to check the position of the fetus, abnormal pregnancy, fetal age and others. Unfortunately, all these things still need to analyze the role of the obstetrician in the sense of image raised by ultrasonography. One of the most striking is the determination of gestational age. Usually, it is done by measuring the length of the fetus manually by obstetricians. In this study, we developed a computer-aided diagnosis for the determination of gestational age by measuring the length of the fetus automatically using edge detection method and image morphology. Results showed that the system is sufficiently accurate in determining the gestational age based image processing.

Keywords: computer aided diagnosis, gestational age, and diameter of uterus, length of fetus, edge detection method, morphology image

Procedia PDF Downloads 294

Authors: Hwan Su Jung, Ahn Jun Gil, Jong Tae Kim

Abstract:

Power management techniques are necessary to save power in the microprocessor. By changing the frequency and/or operating voltage of processor, DVFS can control power consumption. In this paper, we perform a case study to find optimal power state transition for DVFS. We propose the equation to find the optimal ratio between executions of states while taking into account the deadline of processing time and the power state transition delay overhead. The experiment is performed on the Cortex-M4 processor, and average 6.5% power saving is observed when DVFS is applied under the deadline condition.

Keywords: deadline, dynamic voltage frequency scaling, power state transition

Procedia PDF Downloads 456

Authors: Abiodun Ezekiel Adesina, Alice M. Olagunju

Abstract:

This study determined the effects of Computer Assisted Instructions (CAI) and Academic Self-Concepts (ASC) on pre-service teachers’ achievement in AE concepts in CoE in Southwest, Nigeria. The study adopted pretest-posttest, control group, quasi-experimental design. Six CoE with e-library facilities were purposively selected. Two hundred and thirty-two intact 200 level Agricultural education students offering introduction to AE course across the six CoE were participants. The participants were assigned to three groups (D&PM, 77, TM, 73 and control, 82). Treatment lasted eight weeks. The AE achievement test (r=0.76), pre-service teachers’ ASC Scale (r=0.81); instructional guides for tutorial (r=0.76), drill and practice (r=0.81) and conventional lecture modes (r=0.83), and teacher performance assessment sheet were used for data collection. Data were analysed using analysis of covariance and Scheffe post-hoc at 0.05 level of significance. The participants were 55.6% female with mean age of 20.8 years. Treatment had significant main effects on pre-service teachers’ achievement (F(2,207)=60.52; η²=0.21; p < 0.05). Participants in D&PM (x̄ =27.83) had the best achievement compared to those in TM (x̄ =25.41) and control (x̄ =18.64) groups. ASC had significant main effect on pre-service teachers’ achievement (F(1,207)=22.011; η²=0.166; p < 0.05). Participants with high ASC (x̄ =27.52) had better achievement compared to those with low ASC (x̄ =22.37). The drill and practice and tutorial instructional modes enhanced students’ achievement in Agricultural Economics concepts. Therefore, the two instructional modes should be adopted for improved learning outcomes in agricultural economics concepts among pre-service teachers.

Keywords: achievement in agricultural economics concepts, colleges of education in southwestern Nigeria, computer-assisted instruction, drill and practice instructional mode, tutorial instructional mode

Procedia PDF Downloads 203