Search results for: stress urinary incontinence

Authors: Yassa Nacera, Badji Abderrezak, Saidoune Abdelmalek, Houassine Hamza

Abstract:

Several kinds of faults can occur in a permanent magnet synchronous machine (PMSM) systems: bearing faults, electrically short/open faults, eccentricity faults, and demagnetization faults. Demagnetization fault means that the strengths of permanent magnets (PM) in PMSM decrease, and it causes low output torque, which is undesirable for EVs. The fault is caused by physical damage, high-temperature stress, inverse magnetic field, and aging. Motor current signature analysis (MCSA) is a conventional motor fault detection method based on the extraction of signal features from stator current. a simulation model of the PMSM under partial demagnetization and uniform demagnetization fault was established, and different degrees of demagnetization fault were simulated. The harmonic analyses using the Fast Fourier Transform (FFT) show that the fault diagnosis method based on the harmonic wave analysis is only suitable for partial demagnetization fault of the PMSM and does not apply to uniform demagnetization fault of the PMSM.

Keywords: permanent magnet, diagnosis, demagnetization, modelling

Procedia PDF Downloads 68

Authors: Emdad K. Z. Balanji, M. Neaz Sheikh, Muhammad N. S. Hadi

Abstract:

This paper presents results of an experimental investigation on the behaviour of Hybrid Steel Fibre Reinforced High Strength Concrete (HSFR-HSC) cylinder specimens (150 mm x 300 mm) under uniaxial compression. Three different combinations of HSFR-HSC specimens and reference specimens without steel fibres were prepared. The first combination of HSFR-HSC included 1.5% Micro Steel (MS) fibre and 1% Deformed Steel (DS) fibre. The second combination included 1.5% MS fibre and 1.5% Hooked-end Steel (HS) fibre. The third combination included 1% DS fibre and 1.5% HS fibre. The experimental results showed that the addition of hybrid steel fibres improved the ductility of high strength concrete. The combination of MS fibre and HS fibre in high strength concrete mixes showed best stress-strain behaviour compared to the other combinations and the reference specimens.

Keywords: high strength concrete, micro steel fibre (MS), deformed steel fibre (DS), hooked-end steel fibre (HS), hybrid steel fibre

Procedia PDF Downloads 544

Authors: Mohd Anuar Awang Idris, Muhammad Nubli Abdul Wahab, Nora Yusma Mohamed Yusoff

Abstract:

Wudu’ (Ablution) and Zikr are amongst some of the spiritual tools which may help an individual control his mind, emotion and attitude. These tools are deemed to be able to deliver a positive impact on an individual’s psychophysiology. The main objective of this research is to determine the effects of Wudu’ (Ablution) and Zikr therapy using the biofeedback emWave application and technology. For this research, 13 students were selected as samples from the students’ representative body at the University Tenaga National, Malaysia. The DASS (Depression Anxiety Stress Scale) questionnaire was used to help with the assessment and measurement of each student’s ability in controlling his or her emotions before and after the therapies. The biofeedback emWave technology was utilized to monitor the student’s psychophysiology level. In addition, the data obtained from the Heart rate variability (HRV) test have also been used to affirm that Wudu’ and Zikr had had significant impacts on the student’s success in controlling his or her emotional pressure.

Keywords: biofeedback EmWave, emotion, psychophysiology, wudu’, zikr

Procedia PDF Downloads 206

Authors: Omaymah Al-Otoom, Rajesh Mehta

Abstract:

Introduction: Migration is an established risk factor in the development of schizophrenia and other forms of psychosis. The exposure to different social adversities, including social isolation, discrimination, and economic stress, is thought to contribute to elevated rates of psychosis in immigrants and their children. We present a case of resistant schizophrenia in an immigrant adolescent. Case: The patient is a 15-year-old male immigrant. In October 2021, the patient was admitted for irritability, suicidal ideations, and hallucinations. He was treated with Fluoxetine 10 mg daily for irritability. In November 2021, he presented with similar manifestations. Fluoxetine was discontinued, and Risperidone 1 mg at bedtime was started for psychotic symptoms. In March 2022, he presented with commanding auditory hallucinations (voices telling him that people were going to kill his father). Risperidone was gradually increased to 2.5 mg twice daily for hallucinations. The outpatient provider discontinued Risperidone and started Olanzapine 7.5 mg and Lurasidone 40 mg daily. In August 2022, he presented with worsening paranoia due to medication non-adherence. The patient had limited improvement on medications. In October 2022, the patient presented to the ED for visual hallucinations and aggression towards the family. His medications were Olanzapine 10 mg daily, Lurasidone 60 mg daily, and Haloperidol 2.5 mg twice daily. In the ED, he received multiple as-needed medications and was placed in seclusion for his aggressive behavior. The patient showed a positive response to a higher dose of Olanzapine and decreased dose of Lurasidone. The patient was discharged home in stable condition. Two days after discharge, he was brought for bizarre behavior, visual hallucinations, and homicidal ideations at school. Due to concerns for potential antipsychotic side effects and poor response, Lurasidone and Olanzapine were discontinued, and he was discharged home on Haloperidol 5 mg in the morning and 15 mg in the evening. Clozapine treatment was recommended on an outpatient basis. He has no family history of psychotic disorders. He has no history of substance use. A medical workup was done, the electroencephalogram was normal, and the urine toxicology was negative. Discussion: Our patient was on three antipsychotics at some point with no improvement in his psychotic symptoms, which qualifies as treatment-resistant schizophrenia (TRP). It is well recognized that migrants are at higher risk of different psychiatric disorders, including posttraumatic stress disorder, affective disorders, schizophrenia, and psychosis. This is thought to be related to higher exposure to traumatic life events compared to the general population. In addition, migrants are more likely to experience poverty, separation from family members, and discrimination which could contribute to mental health issues. In one study, they found that people who migrated before the age of 18 had twice the risk of psychotic disorders compared to the native-born population. It is unclear whether migration increases the risk of treatment resistance. In a Canadian study, neither ethnicity nor migrant status was associated with treatment resistance; however, this study was limited by its small sample size. There is a need to implement psychiatric prevention strategies and outreach programs through research to mitigate the risk of mental health disorders among immigrants.

Keywords: psychosis, immigrant, adolescent, treatment resistant schizophrenia

Procedia PDF Downloads 116

Authors: Lablali Mohammed, Mes-Adi Hassan, Mazroui M’Hammed

Abstract:

To tackle the complexity of grasping atomic-scale structures and unraveling the factors affecting the development of thin films. In our work, we perform the deposition of Nb atoms on Cu substrates using the molecular dynamics simulation combined with the embedded atom method to describe the interaction between different atoms. We investigated the impact of varying deposition rates and thermal annealing processes on the microstructural, morphological, and mechanical characteristics of the deposited Nb film. Our findings reveal that Nb atom growth on the Cu substrate occurs in island mode, accompanied by the presence of nucleation phenomena during growth. On the other hand, mixing behavior was observed at the interface between the film and the substrate, where Nb penetration is initially limited to the first Cu layer, whereas Cu atoms diffuse until reaching the third layer in the Nb film. Furthermore, Nb exhibits a BCC structure, with a significant concentration observed at a rate of 5 atoms/ps, and annealing further amplifies these percentages. Deposition at different rates leads to distinct levels of compressive normal and biaxial stress.

Keywords: molecular dynamics, Nb thin film, structure and morphology, atomic penetration

Procedia PDF Downloads 31

Authors: Richard Chen

Abstract:

The study is mainly focused on the influence of different kinds of friendships on the well being of Chinese high school students. The main objective is to find out whether friendship style focusing on depth rather than breadth and whether making friends based on similarities in personality and character rather than interests and hobbies improve students’ mental state. Overall, 262 high school participants completed our study by filling out questionnaires online across China. Data showed, unexpectedly, optimal combinations of friendship styles indicate that students who seek depth of connection in friendship benefit more by focusing more on hobbies than on personalities, and those aiming to expand their social connections would be happier and less stressed when they made friends with those who shared their personalities rather than hobbies. The relationship between stress and the frequency of self-talk was also investigated, and a positive correlation between the pressure a student felt, and the frequency of self-talk behavior was confirmed. The results shed light on relationship management and wellbeing among Chinese high school students and may be applied by counselors and teachers to improve the overall level of satisfaction for Chinese high school students.

Keywords: hobbies, personalities, happiness, pressure, self-talk

Procedia PDF Downloads 145

Authors: Xie Kai, Laith K. Abbas, Chen Dongyang, Yang Fufeng, Rui Xiaoting

Abstract:

Effect of plunging motion on the pitch oscillating NACA0012 airfoil is investigated using computational fluid dynamics (CFD). A simulation model based on overset grid technology and k - ω shear stress transport (SST) turbulence model is established, and the numerical simulation results are compared with available experimental data and other simulations. Two cases of phase angle φ = 0, μ which represents the phase difference between the pitching and plunging motions of an airfoil are performed. Airfoil vortex generation, moving, and shedding are discussed in detail. Good agreements have been achieved with the available literature. The upward plunging motion made the equivalent angle of attack less than the actual one during pitching analysis. It is observed that the formation of the stall vortex is suppressed, resulting in a decrease in the lift coefficient and a delay of the stall angle. However, the downward plunging motion made the equivalent angle of attack higher the actual one.

Keywords: dynamic stall, pitching-plunging, computational fluid dynamics, helicopter blade rotor, airfoil

Procedia PDF Downloads 226

Authors: Mariam Arif

Abstract:

The objective of the current study is to find out the electoral violence against women and its implications on their political participation. This paper is a qualitative study to get an in-depth analysis of the phenomenon. This study used questionnaires and interviews for findings. This paper attempts to study electoral violence and women in politics in Pakistan. The study concluded that women are subjected to different categories of violence defined as physical violence that involves sexual and bodily harm to a politically active woman or to people associated with her. Social and psychological violence includes class difference, stress, social limitations, family pressure and character assassination. Economic violence is defined as a systematic restriction of access to economic resources available to women thus hinder women active participation in politics (elections). All these violence against women in elections are threat to the integrity of the electoral process of the country that eventually affects women’s participation as voters, party candidates, election officials and political party leaders. It also undermines the free and fair democratic process. This qualitative paper shows a significant negative relationship between electoral violence and women participation in politics.

Keywords: elections, politics, violence, women

Procedia PDF Downloads 159

Authors: Hong Li, Tingxian Li, Xudong Wang, Weibo Yang

Abstract:

Co-limitation of iron (Fe) deficiency in legume nitrogen fixation process is not well understood. Our objectives were to examine how peanut plants cope with Fe deficiency with the rhizobial inoculants and N-nutrient treatments. The study was conducted in the tropical Hainan Island during 2012-2013. The soil was strongly acidic (pH 4.6±0.7) and deficient in Fe (9.2±2.3 mg/kg). Peanut plants were intercropped with cassava. The inoculants and N treatments were arranged in a split-plot design with three blocks. Peanut root nodulation, stem allantoin, amino acids and plant N derived from fixation (P) reduced with declining soil Fe concentrations. The treatment interactions were significant on relative ureide % and peanut yields (P<0.05). Residual fixed N from peanut plants was beneficial to cassava plants. It was concluded that co-variance of Fe deficiency could influence peanut N fixation efficiency and rhizobia and N inputs could help improving peanut tolerance to Fe deficiency stress.

Keywords: amino acids, plant N derived from N fixation, root nodulation, soil Fe co-variance, stem ureide, peanuts, cassava

Procedia PDF Downloads 294

Authors: Benalia Kouini

Abstract:

The basic idea of this study is to promote a polyethylene recycle and local vegetable fiber (alfa) in the development and characterization of a new composite material. In this work, different sizes of fiber alfa (<63 microns, between 63 and 125 microns, 125 and 250 microns) were incorporated into the blends (HDPE / recycled HDPE) with different methods elaboration (extruder twin-screw and twin-cylinder mixer). The fiber was modified by sodium hydroxide in order to evaluate the effect of alkaline treatment on the interfacial adhesion and therefore the properties of composites prepared. These were characterized by various techniques: mechanical (tensile and Charpy impact test), Rheological (melt flow), morphological (SEM). The demonstration of the effect of alkali treatment on alfa fiber was examined by FTIR spectroscopy and morphological analysis. The introduction of alfa treated fiber in the (HDPE/recycled HDPE) increased stress, impact strength and Young's modulus on the contrary, the elongation at break decreased. The results of the mechanical properties showed an improvement is better in extrusion twin-screw mixer than two cylinders.

Keywords: naturel fiber, alfa, recycling, blends, polyethylene

Procedia PDF Downloads 139

Authors: Mulak Moses Yokdi

Abstract:

Correct use of leisure time has suffered neglect in our society and the people ignorantly think that the trend does not matter. The researcher felt concerned about the issue and went on to find out why using FCE, Pankshin workers as a case study. Four hypotheses were used, considering such variables as leadership, traditional activities, stress due to work pressure and time constraint. The participants selected for the study were one hundred and ten members of FCE, Pankshin staff. A self-developed questionnaire was the instrument used. Chi-square (x2) was employed to test the hypotheses at P = 0.005; df = 3. The statistics of percentages was also used to describe the situation as implicated by the data. The results showed that all hypotheses were significant (P = 0.05). It was concluded that the four variables were impediments to effective participation in physically oriented leisure time activities among the FCE, Staff. Based on the findings, it was recommended that the FCE should get good leadership, create good awareness for people to understand why they should be effectively involved in physically oriented leisure time activities.

Keywords: barriers, effective participation, leisure time, physically oriented, work pressure, time constraint

Procedia PDF Downloads 368

Authors: Rajnish Gupta, R. S. Gupta

Abstract:

Present research was aimed to investigate antidiabetic and antioxidant status of Lupeol in streptozotocin induced diabetes. Rats were divided into following groups mainly: control, diabetic, normal group as well as diabetic treated with Lupeol at 25 and 35 mg/kg b.wt./day for 21 days, diabetic group treated with glibenclamide. Tissue (pancreas, kidney and liver) as well as serum biochemical parameters were analysed for any abnormal behavior. Lupeol administration reduced diabetes onset with significant improvement in serum insulin level also strengthened by increase in β-Cell counts. A significant decrease was observed in serum glucose level. Furthermore, Lupeol treatment increased the antioxidant enzymes, glycolytic enzymes and also protein levels with a decrease in the level of thiobarbituric acid-reactive oxygen species and gluconeogenic enzymes. Present study proves that Lupeol administration significantly reinstated serum and tissue biochemical parameters and thus strengthening its antidiabetic potential.

Keywords: oxidative stress, pterostilbene, thiobarbituric acid, reactive oxygen species

Procedia PDF Downloads 470

Authors: Mary T. McKinley

Abstract:

As socio-economic globalization impacts education and turns knowledge into a commodity, institutions of higher education are becoming more intentional about infusing a global and intercultural perspective into education via the recruitment of international students. Coming from dissimilar cultures, many of these students are evaluated and held accountable to Euro-American values of independence, self-reliance, and autonomy. Not surprisingly, these students often experience culture shock with deleterious effects on their mental health and academic functioning. Thus, it is critical to understand the experiences of international students with the hope that such knowledge will keep the field of psychology from promulgating Eurocentric ideals and values and prevent the training of these students as good-enough White therapists. Using a critical narrative inquiry framework, this study elicits stories about the challenges encountered by international students as they navigate their clinical training in the presence of acculturative stress and potentially different worldviews. With its emphasis on story-telling as meaning making, narrative research design is hinged on the assumption that people are interpretive beings who make meaning of themselves and their world through the language of stories. Also, dominant socially-constructed narratives play a central role in creating and maintaining hegemonic structures that privilege certain individuals and ideologies at the expense of others. On this premise, narrative inquiry begins with an exploration of the experiences of participants in their lived stories. Bounded narrative segments were read, interpreted, and analyzed using a critical events approach. Throughout the process, issues of reliability and researcher bias were addressed by keeping a reflective analytic memo, as well as triangulating the data using peer-reviewers and check-ins with participants. The findings situate culture at the epicenter of international students’ acculturation challenges as well as their resiliency in psychology doctoral programs. It was not uncommon for these international students to experience ethical dilemmas inherent in learning content that conflicted with their cultural beliefs and values. Issues of cultural incongruence appear to be further exacerbated by visible markers for differences like speech accent and clothing attire. These stories also link the acculturative stress reported by international students to the experiences of perceived racial discrimination and lack of support from the faculty, administration, peers, and the society at large. Beyond the impact on the international students themselves, there are implications for internationalization in psychology with the goal of equipping doctoral programs to be better prepared to meet the needs of their international students. More than ever before, programs need to liaise with international students’ services and work in tandem to meet the unique needs of this population of students. Also, there exists a need for multiculturally competent supervisors working with international students with varying degrees of acculturation. In addition to making social justice and advocacy salient in students’ multicultural training, it may be helpful for psychology doctoral programs to be more intentional about infusing cross-cultural theories, indigenous psychotherapies, and/or when practical, the possibility for geographically cross-cultural practicum experiences in the home countries of international students while taking into consideration the ethical issues for virtual supervision.

Keywords: decolonizing pedagogies, international students, multiculturalism, psychology doctoral programs

Procedia PDF Downloads 118

Authors: Yuxin Wu, Yu-Shing Wang, Zitao Zhang

Abstract:

A high-speed and time-lapse S-wave velocity measurement system has been built up for S-wave tomography in sand. This system is based on bender elements and applied to model pile tests in a tailor-made pressurized chamber to monitor the shear wave velocity distribution during pile installation in sand. Tactile pressure sensors are used parallel together with bender elements to monitor the stress changes during the tests. Strain gages are used to monitor the shaft resistance and toe resistance of pile. Since the shear wave velocity (Vs) is determined by the shear modulus of sand and the shaft resistance of pile is also influenced by the shear modulus of sand around the pile, the purposes of this study are to time-lapse monitor the S-wave velocity distribution change at a certain horizontal section during pile installation and to correlate the S-wave velocity distribution and shaft resistance of pile in sand.

Keywords: bender element, pile, shaft resistance, shear wave velocity, tomography

Procedia PDF Downloads 429

Authors: Rizwan Ullah, Abdar Ali, Zahid Ullah

Abstract:

This paper illustrates the study of three isolated zero voltage switched (ZVS) PWM full bridge (FB) converters to charge the high voltage battery in the charger of electric vehicle (EV). EV battery chargers have several challenges such as high efficiency, high reliability, low cost, isolation, and high power density. The cost of magnetic and filter components in the battery charger is reduced when switching frequency is increased. The increase in the switching frequency increases switching losses. ZVS is used to reduce switching losses and to operate the converter in the battery charger at high frequency. The performance of each of the three converters is evaluated on the basis of ZVS range, dead times of the switches, conduction losses of switches, circulating current stress, circulating energy, duty cycle loss, and efficiency. The limitations and merits of each PWM FB converter are reviewed. The converter with broader ZVS range, high efficiency and low switch stresses is selected for battery charger applications in EV.

Keywords: electric vehicle, PWM FB converter, zero voltage switching, circulating energy

Procedia PDF Downloads 439

Authors: Semih Erdogan

Abstract:

In this paper, the normal and shear stress distributions in Vlasov beams are determined by two-dimensional triangular finite element formulations. The proposed formulations take into account the warping effects along the beam axis. The shape of the considered beam sections may be arbitrary and varied throughout its length. The stiffness matrices and force vectors are derived for transversal forces, uniform torsion, and nonuniform torsion. The proposed finite element algorithm is validated by comparing the analytical solutions, structural engineering books, and related articles. The numerical examples include beams with different cross-section types such as solid, thick-walled, closed-thin-walled, and open-thin-walled sections. Materials defined in the examples are homogeneous, isotropic, and linearly elastic. Through these examples, the study demonstrates the capability of the proposed method to address a wide range of practical engineering scenarios.

Keywords: Vlasov beams, warping function, nonuniform torsion, finite element method, normal and shear stresses, cross-section properties

Procedia PDF Downloads 64

Authors: Worrapol Koranuntachai, Tonkid Chantrasmi, Udomkiat Nontakaew

Abstract:

Medical latex gloves are made from the latex compound in production lines. Latex dipping is considered one of the most important processes that directly affect the final product quality. In a continuous production line, a chain conveyor carries the formers through the process and partially submerges them into an open channel flow in a latex dipping tank. In general, the conveyor speed is determined by the desired production capacity, and the latex-dipping tank can then be designed accordingly. It is important to understand the flow behavior in the dipping tank in order to achieve high quality in the process. In this work, Computational Fluid Dynamics (CFD) was used to simulate the flow past an array of formers in a simplified latex dipping process. The computational results showed both the flow structure and the vortex generation between two formers. The maximum shear stress over the surface of the formers was used as the quality metric of the latex-dipping process when adjusting operation parameters.

Keywords: medical latex gloves, latex dipping, dipping tank, computational fluid dynamics

Procedia PDF Downloads 132

Authors: Nabil Abaab, Dhaou Akrout, Riadh Ahmadi, Mabrouk Montacer

Abstract:

The study of fluid pressure and its evolution have a critical importance as they lead to understanding the tectonic history of the region. Therefore, the present work focuses on a microtectonic study of tectonic and hydraulic fracture at the anticline structure of Zemlet El Beidha (North Chott range). The study and the analysis of several stations of tectonic and hydraulic fracture allow revealing the witnesses of a paléosurpression in the deposits of Lower Cretaceous (Bouhedma Formation). In fact, we noticed that the overpressure is directly involved in the creation of various types of fractures as evidenced by the different measures and the stereographic projections. Thus, the orientations of fibers of mineralization that fills the Beefs type fracture have the same direction as the main constraint. Furthermore, we discussed the different overpressure build-up mechanisms. The results showed that tectonics is likely, responsible for this anomaly. This is confirmed by the description of the fibers and the projection of the different measurements of Beefs. The mineralization transformation from gypsum to anhydrite is heavily involved in this stress regime especially in the presence of all necessary conditions of dehydration of gypsum.

Keywords: Zemlet El Beidha, overpressure, tectonic fracture, hydraulic fracture, gypsum beefs

Procedia PDF Downloads 286

Authors: Liu Dan

Abstract:

It was considered either unnecessary or impossible for primary school students to implement online teaching until last year. A large number of E-learning or E-teaching researches have been focused on adult-learners, andragogy and technology, however, primary school education, it is facing many problems that need to be solved. Therefore, this research is aimed at exploring barriers and influential factors on online teaching for K-12 students from teachers’ perspectives and discussing the E-pedagogy that is suitable for primary school students and teachers. Eight hundred and ninety-six teachers from 10 primary schools in Shanghai were invited to participate in a questionnaire survey. Data were analysed by hierarchical regression, and the results stress the significant three barriers by teachers with online teaching: the existing system is deficient in emotional interaction, teachers’ attitude towards the technology is negative and the present teacher training is lack of systematic E-pedagogy guidance. The barriers discovered by this study will help the software designers (E-lab) develop tools that allow for flexible and evolving pedagogical approaches whilst providing an easy entry point for cautious newcomers, so that help the teachers free to engage in E-teaching at pedagogical and disciplinary levels, to enhance their repertoire of teaching practices.

Keywords: online teaching barriers (OTB), e-teaching, primary school, teachers, technology

Procedia PDF Downloads 201

Authors: Zhiming Ye, Dejiang Wang, Huiling Zhao

Abstract:

Development of the technology demands a higher-level research on the mechanical behavior of materials. Structural members made of bi-modulus materials have different elastic modulus when they are under tension and compression. The stress and strain states of the point effect on the elastic modulus and Poisson ratio of every point in the bi-modulus material body. Accompanied by the uncertainty and nonlinearity of the elastic constitutive relation is the complicated nonlinear problem of the bi-modulus members. In this paper, the small displacement and large displacement finite element method for the bi-modulus members have been proposed. Displacement nonlinearity is considered in the elastic constitutive equation. Mechanical behavior of slender bi-modulus beam-column under different boundary conditions and loading patterns has been simulated by the proposed method. The influence factors on the ultimate bearing capacity of slender beam and columns have been studied. The results show that as the ratio of tensile modulus to compressive modulus increases, the error of the simulation employing the same elastic modulus theory exceeds the engineering permissible error.

Keywords: bi-modulus, ultimate capacity, beam-column, nonlinearity

Procedia PDF Downloads 412

Authors: Abdul Halim Abdul, Wan Ismail Wan Yusoff

Abstract:

The geological formation at Limau Manis Besar area, are consist of low grade metamorphic rock and undulating mountaineers, rugged terrain and the quite steeply 45 degree slope gradient. The objectives of this paper are present the methods and devices used in measurement of P-wave velocity to estimate the initial Shear Modulus (Go) in steady state and critical state soil consolidation. The relationship between SPT-N values and the Shear Modulus (Go) at very small strain is widely considered to be evaluated. Based on the seismic reflection survey, the constant (K) poroelastic theory, mean effectives stress and primer wave velocity (Vs) increase as the soil depth increase. The steady state and critical state, Degree of Soil Consolidation(U) concept is used to interpret the behavior of Shear Modulus (Go). The relationship between Consolidation Test and Seismic Reflection Survey is also discussed.

Keywords: geological setting, shear modulus, poroelastic theory, steady state and none steady state degree of soil consolidation, consolidation test

Procedia PDF Downloads 474

Authors: E. P. Doku-Asare, A. Essuman

Abstract:

The materials used for the production of holders are mainly metals and plastic, and these materials are difficult and expensive to process; therefore, the need to explore other materials such as clay for the production of holders. Clay is a viable material for the production of holders due to its plastic nature. Using ceramic materials as a medium for the production of holders does not only serve its purpose but also economically cheaper since the material is mined in Ghana. The study also examines the aesthetic nature of the holders due to the properties found in the material used. Six holders were chosen and were made in a manner that would not take a lot of space. They are Pin holders, Paper holders, Penholders, Paperweight and Umbrella holders. The production technique employed in the execution of this project were the slab method, throwing, and press mold. Results indicated that ceramic holders are durable and long-lasting and can serve the purpose of metallic and plastic holders. The study also found that clay holders are durable due to the fact that clay is from a natural source which ensures permanence and resistance to stress. It is recommended that press molds be used in the production of holders. Clay holders last longer due to the useful properties of clay including very high hardness and strength.

Keywords: ceramics, interior design, Ghana, production technique

Procedia PDF Downloads 166

Authors: Amar Al-Obaidi, Verena Kräusel, Dirk Landgrebe

Abstract:

Induction assisted single point incremental forming (IASPIF) is a flexible method and can be simply utilized to form a high strength alloys. Due to the interaction between the mechanical and thermal properties during IASPIF an evaluation for the process is necessary to be performed analytically. Therefore, a numerical simulation was carried out in this paper. The numerical analysis was operated at both room and elevated temperatures then compared with experimental results. Fully coupled dynamic temperature displacement explicit analysis was used to simulated the hot single point incremental forming. The numerical analysis was indicating that during hot single point incremental forming were a combination between complicated compression, tension and shear stresses. As a result, the equivalent plastic strain was increased excessively by rising both the formed part depth and the heating temperature during forming. Whereas, the forming forces were decreased from 5 kN at room temperature to 0.95 kN at elevated temperature. The simulation shows that the maximum true strain was occurred in the stretching zone which was the same as in experiment.

Keywords: induction heating, single point incremental forming, FE modeling, advanced high strength steel

Procedia PDF Downloads 208

Authors: Pavel Zabrodin

Abstract:

The drawback of magnesium alloys is poor plasticity, which complicates the forming. Effective way of improving the properties of the cast magnesium alloy AZ31 (3 wt. % Al, 0.8 wt. % Zn, 0.2 wt. % Mn)) is to combine hot extrusion at 350°C and equal-channel angular pressing (ECAP) at 180°C. Because of reduced grain sizes, changes in the nature of the grain boundaries, and enhancement of a texture that favors basal dislocation glide, after this kind of processing, increase yield stress and ductility. For study of the effect of microstructure on the mechanisms for plastic deformation, there is some interest in investigating the mechanical properties of the ultrafinegrained (UFG) Mg alloy at low temperatures, before and after annealing. It found that the amplitude and statistics at the low-temperature jump-like deformation the Mg alloy of dependent on microstructure. Reduction of the average density of dislocations and grain growth during annealing causing a reduction in the amplitude of the jump-like deformation and changes in the distribution of surges in amplitude. It found that the amplitude and statistics at the low-temperature jump-like deformation UFG alloy dependent on temperature of deformation. Plastic deformation of UFG alloy at a temperature of 10 K occurs uniformly - peculiarities is not observed. Increasing of the temperature of deformation from 4,2 to 0,5 K is causing a reduction in the amplitude and increasing the frequency of the jump-like deformation.

Keywords: jump-like deformation, low temperature, plasticity, magnesium alloy

Procedia PDF Downloads 455

Authors: Aravindhan Nepolean, Chidamabaranathan Bibin, Rajesh K., Gopinath S., Ashok Kumar R., Arun Kumar S., Sadasivan N.

Abstract:

Wind turbine blades are an important parameter for surging renewable energy production. Optimizing blade profiles and developing new materials for wind turbine blades take a lot of time and effort. Even though many standards for wind turbine blades have been developed for large-scale applications, they are not more effective in small-scale applications. We used acrylonitrile-butadiene-styrene to make small-scale wind turbine blades in this study (ABS). We chose the material because it is inexpensive and easy to machine into the desired form. They also have outstanding chemical, stress, and creep resistance. The blade measures 332 mm in length and has a 664 mm rotor diameter. A modal study of blades is carried out, as well as a comparison with current e-glass fiber. They were able to balance the output with less vibration, according to the findings. Q blade software is used to simulate rotating output. The modal analysis testing and prototype validation of wind turbine blades were used for experimental validation.

Keywords: acrylonitrile-butadiene-styrene, e-glass fiber, modal, renewable energy, q-blade

Procedia PDF Downloads 161

Authors: Chanasit Chaocharoenphat

Abstract:

Hibiscus sabdariffa is a herbal plant that is commonly used for home remedies in Thailand. This study aims to determine the antioxidant activity of polyphenols, as oxidative stress plays a vital role in the development of cancer, and H. sabdariffa was used in this study. The total flavonoids content was determined using the aluminium chloride colourimetric method and expressed as quercetin equivalents (QE)/g and the antioxidant capacity of the flavonoids using the 2,2-diphenyl-1-picrylhydrazyl (DPPH) and 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid) (ABTS) radical scavenging capacity assays. The IC50 values of H. sabdariffa extract were 167.14 μg/mL ± 0.843 and 77.59 μg/mL ± 0.798, respectively. In the DPPH assay, vitamin C was used as a positive control, whereas Trolox was used as a positive control in the ABTS assay. To summarise, H. sabdariffa extract contains a high concentration of total flavonoids and exhibits potent antioxidant activity. However, additional antioxidant activity assays such as superoxide dismutase (SOD), reactive oxygen species (ROS), and reactive nitrogen species (RNS) scavenging assays and in vitro antioxidant experiments should be carried out to investigate the molecular mechanism of the compound.

Keywords: ABTS assay, antioxidant activity, Gracilaria fisheri, DPPH assays, total flavonoid content

Procedia PDF Downloads 242

Authors: M. Cangi, T. Dolar, C. Ersoy, Y. E. Aydogdu, A. I. Aydeniz, A. Mugan

Abstract:

The drum is one of the critical parts in a washing machine in which the clothes are washed and spin by the rotational movement. It is activated by the drum shaft which is attached to an electric motor and subjected to dynamic loading. Being one of the critical components, failures of the drum require costly repairs of dynamic components. In this study, tolerance bands between the drum shaft and its two bearings were examined to develop a relationship between the fatigue life of the shaft and the interaction tolerances. Optimization of tolerance bands was completed in consideration of the fatigue life of the shaft as the cost function. The following methodology is followed: multibody dynamic model of a washing machine was constructed and used to calculate dynamic loading on the components. Then, these forces were used in finite element analyses to calculate the stress field in critical components which was used for fatigue life predictions. The factors affecting the fatigue life were examined to find optimum tolerance grade for a given test condition. Numerical results were verified by experimental observations.

Keywords: fatigue life, finite element analysis, tolerance analysis, optimization

Procedia PDF Downloads 157

Authors: Jonathan Hinton Westover, Maureen S. Andrade, Doug Miller

Abstract:

Research has been inconclusive in determining if men or women experience more job satisfaction. A global comparison examining extrinsic and intrinsic factors, work relations, and work-life balance determinants found few differences; however, work relations and work-life balance factors were more significant for male than female workers across occupations. The current study uses International Social Survey Program data representing 37 countries to explore gender differences in job satisfaction in the hospitality industry. Findings demonstrate that mean job satisfaction scores for females are lower across hospitality occupations except for hotel receptionists, housekeeping supervisors, and hotel cleaners. Regression results revealed additional differences such as the significance of co-worker relations, the negative impact of being discriminated against and harassed at work, working weekends, marital status, and supervisory status for women with autonomy, work stress, education, and employment relationship being more salient for men. Interesting work, work being useful to society, job security, pay, relations with management, and work interfering with family were significant for both males and females.

Keywords: job satisfaction, gender, hospitality, global comparisons

Procedia PDF Downloads 134

Authors: Oluwasgun Moses Jolayemi

Abstract:

Violence has become a fairly often occurrence in sports (within our tertiary institutions), a development that is giving every society in the world sleepless night. School violence is part of youth violence, a broader salient public health problem. This study employing a questionnaire-based survey strategy aimed at investigates psychological factors as predictors of sports violence among Oyo state tertiary institution. A sample of Two hundred athletes and three tertiary institutions were selected through purposive sampling from the Oyo State tertiary institution. The estimated reliability co-efficient of the instrument was found to be 0.89 using cronbach Alpha technique. Data were analyzed at 0.05 level of significance using Statistical Package for the Social Sciences (SPSS) software, version 20.0. Five hypotheses were tested using Pearson Correlation. Result revealed that personality, anxiety, mental health has no significant influence on sports violence; mental stress has a significant influence on sports violence. Based on the findings, it was recommended that sport management should reduce work overload and that they should organized seminars and social activities to help athletes lose up.

Keywords: Ibadan, mental health, personality, psychology, violence

Procedia PDF Downloads 303

Authors: D. V. S. Praneeth, V. R. Sankar Cheela, Brajesh Dubey

Abstract:

Coal Combustion (CC) residues are the major by-products from thermal power plants. The disposal of ash on to land creates havoc to environment and humans. The leaching of the constituent elements pollutes ground water. Beneficiary use of coal combustion residues in structural components is being investigated as a part of this study. This application reduces stress on the convention materials in the construction industry. The present study involves determination of leaching parameters of the CC residues. Batch and column studies are performed based on Leaching Environmental Assessment Framework (LEAF) protocol. The column studies are conducted to simulate the real time percolation conditions in the field. The structural and environmental studies are performed to determine the usability of CC residues as bricks. The physical, chemical, geo environmental and mechanical properties of the alternate materials are investigated. Scanning electron microscopy (SEM), X-Ray Diffraction analysis (XRD), X-ray fluorescence (XRF) and Energy Dispersive X-ray Spectroscopy tests were conducted to determine the characteristics of CC residue ash and bricks.

Keywords: coal combustion residues, LEAF, leaching, SEM

Procedia PDF Downloads 314