Search results for: comparison group

Authors: M. Soltani, K. Pakzad, A. Haghigh-Khiyabani, M. Alavi, R. Naderi, M. Castex

Abstract:

Effect of probiotic Bactocell (Pediococcus acidilactici) as a supplementary diet was studied on post-larvae 12-15 of white leg shrimp (Litopenaeus vannamei) (150000 PL/0.5 h pond, average body weight=0.02 g) growth performance under farm condition for 102 days at water quality parameters consisting of temperature at 30.5-36οC, dissolved oxygen 4.1-6.6 mg/l, salinity 40-54 g/l, turbidity 35-110 cm, ammonia 0.1-0.8 mg/l and nitrite 0.1-0.9 mg/l. Also, the resistance level of the treated shrimps was assessed against a virulent strain of Vibrio paraheamolyticus as intramuscular injection route at 1.4 x 106 cells/shrimp. Significantly higher growth rate (11.3±1.54 g) and lower feed conversion ratio (1.1) were obtained in shrimps fed diets supplemented with Bactocell at 350 g/ tone feed compared to other treatments of 250 g Bactocell/ton feed (10.8±2 g, 1.3), 500 g Bactocell/ton feed (10.3±1.7 g, 1.3) and untreated control (10.1±2 g, 1.4). Also, thermal growth coefficient (0.057%) and protein efficiency ratio (2.13) were significantly improved in shrimps fed diets supplemented with Bactocell at 350 g/ton feed compare to other groups. Shrimps fed diet supplemented with Bactocell at 350 g/tone feed showed significantly higher protein content (72.56%) in their carcass composition than treatments of 250 g/ton feed (65.9%), 500 g/ton feed (67.5%) and control group (65.9%), while the carcass contents of moisture, lipid and ash in all shrimp groups were not significantly affected by different concentrations of Bactocell. No mortality occurred in the experimentally infected shrimps fed with Bactocell at 500 g/tone feed after 7 hours post-challenge with V. parahemolyticus. The mortality levels of 100%, 40%, 50% and 70% were obtained in shrimps fed with 0.0, 500 g/tone feed, 350 g/ton feed and 250 g/ton feed, respectively 14 hours post-infection. Also, the cumulative mortalities were achieved in 100%, 92% and 81% in shrimps few with Bactocell at 500 g/ton feed, 250 g/ton feed and 350 g/ton feed, respectively.

Keywords: litopenaeus vannamei, vibrio paraheamolyticus, pediococcus acidilactici, growth performance, bactocell

Procedia PDF Downloads 661

Authors: Alexandra-Veronica Luca, Letitia Petrescu

Abstract:

Steel production is a major contributor to global warming potential. An average value of 1.83 tons of CO₂ is emitted for every ton of steel produced, resulting in over 3.3 Mt of CO₂ emissions each year. The present paper is focused on the investigation and comparison of two O₂ separation methods and two CO₂ capture technologies applicable to iron and steel industry. The O₂ used in steel production comes from an Air Separation Unit (ASU) using distillation or from air separation using membranes. The CO₂ capture technologies are represented by a two-stage membrane separation process and the gas-liquid absorption using methyl di-ethanol amine (MDEA). Process modelling and simulation tools, as well as environmental tools, are used in the present study. The production capacity of the steel mill is 4,000,000 tones/year. In order to compare the two CO₂ capture technologies in terms of efficiency, performance, and sustainability, the following cases have been investigated: Case 1: steel production using O₂ from ASU and no CO₂ capture; Case 2: steel production using O₂ from ASU and gas-liquid absorption for CO₂ capture; Case 3: steel production using O₂ from ASU and membranes for CO₂ capture; Case 4: steel production using O₂ from membrane separation method and gas-liquid absorption for CO₂ capture and Case-5: steel production using membranes for air separation and CO₂ capture. The O₂ separation rate obtained in the distillation technology was about 96%, and about 33% in the membrane technology. Similarly, the O₂ purity resulting in the conventional process (i.e. distillation) is higher compared to the O₂ purity obtained in the membrane unit (e.g., 99.50% vs. 73.66%). The air flow-rate required for membrane separation is about three times higher compared to the air flow-rate for cryogenic distillation (e.g., 549,096.93 kg/h vs. 189,743.82 kg/h). A CO₂ capture rate of 93.97% was obtained in the membrane case, while the CO₂ capture rate for the gas-liquid absorption was 89.97%. A quantity of 6,626.49 kg/h CO₂ with a purity of 95.45% is separated from the total 23,352.83 kg/h flue-gas in the membrane process, while with absorption of 6,173.94 kg/h CO₂ with a purity of 98.79% is obtained from 21,902.04 kg/h flue-gas and 156,041.80 kg/h MDEA is recycled. The simulation results, performed using ChemCAD process simulator software, lead to the conclusion that membrane-based technology can be a suitable alternative for CO₂ removal for steel production. An environmental evaluation using Life Cycle Assessment (LCA) methodology was also performed. Considering the electricity consumption, the performance, and environmental indicators, Case 3 can be considered the most effective. The environmental evaluation, performed using GaBi software, shows that membrane technology can lead to lower environmental emissions if membrane production is based on benzene derived from toluene hydrodealkilation and chlorine and sodium hydroxide are produced using mixed technologies.

Keywords: CO₂ capture, gas-liquid absorption, Life Cycle Assessment, membrane separation, steel production

Procedia PDF Downloads 275

Authors: Emad Mohammed Sani

Abstract:

Women encounter exclusion and discrimination in varying degrees, particularly those who marry as minors. The detrimental custom of getting married young is still prevalent worldwide and affects millions of people. It has been less common over time, although it is still widespread in underdeveloped nations. Oromia Regional State is the region in Ethiopia with the highest proportion of child brides. This study aimed at evaluating the effects of early marriage on its survivors’ life conditions – specifically, empowerment and household decision-making – in Eastern Hararghe Zone of Oromia Region. This study employed community-based cross-sectional study design. It adopted mixed method approach – survey, in-depth interview and focus group discussion (FGD) – to collect, analyses and interpret data on early marriage and its effects on household decision-making processes. Narratives and analytical descriptions were integrated to substantiate and/or explain observed quantitative results, or generate contextual themes. According to this study, married women who were married at or after the age of eighteen participated more in household decision-making than child brides. Child brides were more likely to be victims of violence and other types of spousal abuse in their marriages. These changes are mostly caused by an individual's age at first marriage. Delaying marriage had a large positive impact on women's empowerment at the household level, and age at first marriage had a considerable negative impact. In order to advance women's welfare and emancipation, we advise more research to concentrate on the relationship between the home and the social-structural forms that appear at the individual and communal levels.

Keywords: child-bride, early marriage, women, ethiopia

Procedia PDF Downloads 51

Authors: Silke Bustamante, Andrea Pelzeter, Andreas Deckmann, Rudi Ehlscheidt, Franziska Freudenberger

Abstract:

Against the background of demographic changes and the need for motivated and talented employees, companies have a growing interest in being perceived as an attractive employer and gain a competitive edge in the market for talents. Research indicates that corporate social responsibility plays an important role employer choice. This is assumed to be particularly true for the cohorts of the so-called generations y younger applicants born later. Several studies identified cultural, educational and generational differences in CSR preferences. However, until now literature that links preferences for employers’ responsibility with the individual value orientation of the job applicant is scarce. This paper seeks to close this gap and analyzes the preference structure of 500 German university graduates for CSR-related and non-CSR-related employer attributes contingent on their value orientation. In a first step, we identified 17 CSR related attributes in five CSR dimensions (ecology, community, workplace, governance, and market) as well as 11 traditional attributes such as salary, reputation, personal development etc. based on literature review and focus groups. We then used an adapted Conjoint Analysis framework in order to understand the relative preference of each attribute for each participant. Additionally, we surveyed the value orientation of participants based on the European Social Survey (ESS) 21-item human values scale that allow a differentiation of participants into clusters of value orientation. The results allow us not only to operationalize preferences for CSR and other important employer attributes, but – more importantly – to answer the question how different values structures play together with CSR preferences of potential employees. They hereby allow companies to customize employee directed messages to their respective target group and design their employer brand accordingly.

Keywords: corporate social responsibility, employer attractiveness, employer brand, recruiting, values

Procedia PDF Downloads 274

Authors: Kulwinder Singh

Abstract:

Punjab is one of the major labour exporting states of India. Every year more than 20,000 youths from Punjab attempt irregular migration. About 84 irregular migrants are from rural areas and 16 per cent from urban areas. Irregular migration could only be achieved if be organized through highly efficient international networks with the countries of origin, transit, and destination. A good number of Punjabis continue to immigrate into the UK for work through unauthorized means entering the country on visit visas and overstaying or getting ‘smuggled into’ the country with the help of transnational networks of agents. Although, the efforts are being made by the government to curb irregular migration through The Punjab Prevention of Human Smuggling Rules (2012, 2014) and Punjab Travel Regulation Act (2012), but yet it exists parallel to regular migration. Despite unprecedented miseries of irregular migrants and strict laws implemented by the state government to check this phenomenon, ‘why do Punjabis migrate abroad irregularly’ is the important question to answer. This study addresses this question through the comparison of irregular migration with regular one. In other words, this analysis reveals major causes, specifically economic ones, of irregular migration from rural Punjab. This study is unique by presenting economics of irregular migration, given previous studies emphasize the role of sociological and psychological factors. Addressing important question “why do Punjabis migrate abroad irregularly?”, the present study reveals that Punjabi, being far-sighted, endeavor irregular migration as it is, though, economically nonviable in short run, but offers lucrative economic gains as gets older. Despite its considerably higher cost viz-a-viz regular migration, it is the better employment option to irregular migrants with higher permanent income than local low paid jobs for which risking life has become the mindset of the rural Punjabis. Although, it carries considerably lower economic benefits as compared to regular migration, but provides the opportunity of migrating abroad to less educated, semi-skilled and language-test ineligible Punjabis who cannot migrate through regular channels. As its positive impacts on source and destination countries are evident, it might not be restricted, rather its effective management, through liberalising restrictive migration policies by destination nations, can protect the interests of all involved stakeholders.

Keywords: cost, migration, income, irregular, regular, remittances

Procedia PDF Downloads 109

Authors: Eny Suastuti

Abstract:

This paper is about state’s capital equity in establishing State-owned Company (PT Merpati Persero). Under private law regime, PT Merpati Persero equity is a state asset allocated separately from the State Budget. Consequently, it is no longer a state asset; rather, it becomes a part of company assets. The adoption of Act No. 17 of 2003 on State Finance, Act No. 31 of 1999, which is amended by Act No. 20 of 2001 on Eradication of Corrupt Practices, Act No. 15 of 2004 on Auditing, Management, and Accountability of State Finance, and Act No. 15 of 2006 Audit Board raises legal issues of whether State-owned Company’s (PT Merpati Persero) loss may be deemed as loss on state finance made by the Directors of PT Merpati Persero, which implication leads to corrupt practices conducted by the Directors. The principle of civil law states that state assets are separated from the state budget is not a government asset. Therefore the case of a lease agreement 2 (two) units of Boeing 737-400 and Boeing 737-500 between PT Merpati Nusantara Airlines with companies Third Stone Aircraft Leasing Group (TALG) the United States cannot be prosecuted under Articles 2 and 3 of Act No. 31 of 1999 Jo Act No. 20 of 2001 on Eradication of Corrupt Practices (Law PTPK). From this paper, three things are found. First, state’s capital equity, which has been allocated separately from state assets in establishing the PT Merpati Perserois not state asset; rather, it is company’s asset. Second, in the case of mismanagement leading to company loss, the Directors of PT Merpati Persero may not be charged with committing corrupt practice as prescribed in Articles 2 and 3 of Corrupt Practices Eradication Law. Third, misperception has been made by judicial practices since the courts consider loss in certain transaction made by Directors of PT Merpati Persero to be loss of state finance whose implication is applicability of Articles 2 and 3 of Corrupt Practices Eradication Law.

Keywords: corrupt practice, loss, state's capital equity, state finance (PT Merpati Persero)

Procedia PDF Downloads 250

Authors: Nisha Harry, Keshia Sing

Abstract:

Orientation: The Multifactor Leadership Questionnaire (MLF) and the sense of coherence-29 (SCS) is an effective tools to assess the prevalence and underlying structures of empirically based taxonomies related to leadership and wellbeing. Research purpose: The purpose of the study was to test the psychometric properties of the SCS and Multifactor Leadership Questionnaire (MLQ) to screen for psychological wellness indices within the banking industry in South Africa. Motivation for the study: The contribution of these two instruments for the purpose of determining psychological wellness in a banking work environment is unique. Research design, approach, or method: The sample consisted of (N = 150) financial staff employed in a South African banking organisation. The age of the sample was: 37% (30 -40 yrs), 31% (20-30 yrs), 26% (40- 50 yrs), and 6% (50+yrs), of which 52% were males, 48% were females. The white race group was the majority at 29%, African at 26%, Coloured at 23%, and Indian was 22%. Main findings: Results from the exploratory factor analysis revealed a two-factor structure as the most satisfactory. Confirmatory factor analyses revealed the two-factor model displayed better good of-fit indices. Practical implications: The factor structure of the Sense of Coherence-29 scale (SCS), and the Multifactor Leadership Questionnaire (MLQ), have a value-added focus to determine psychological wellness within banking staff. It is essential to take into account these constructs when developing employee wellness interventions. Contribution/value add: Understanding the psychometric properties of the SCS, the self-reported form, and the MLQ questionnaire contributes to screening psychological wellness indices such as coping within the banking industry in a developing country like South Africa. Leaders are an important part of the implementation process of organisational employee wellness practices.

Keywords: factorial structure, leadership, measurement invariance, psychological wellness, sense of coherence

Procedia PDF Downloads 83

Authors: Betty Chiyangwa

Abstract:

This is a work in progress project focused on exploring the complexities surrounding the second generation Mozambican migrant youth’s experiences to construct their identity and develop a sense of belonging in post-apartheid, Bushbuckridge in South Africa. Established in 1884, Bushbuckridge is one of the earliest districts to accommodate Mozambicans who migrated to South Africa in the 1970s. Bushbuckridge as a destination for Mozambican migrants is crucial to their search for social freedom and space to “belong to.” The action of deliberately seeking freedom is known as an act of agency. Four major objectives govern the paper. The first objective observes how second-generation Mozambican migrant youth living in South Africa negotiate and construct their own identities. Secondly, it explores second-generation Mozambican migrant youth narratives regarding their sense of belonging in South Africa. Thirdly, the study intends to understand how social processes of identity and belonging influence second-generation Mozambican migrant youth experiences and future aspirations in South Africa. The last objective examines how Sen’s Capability approach is relevant in understanding second-generation Mozambican migrant youth identity and belonging in South Africa. This is a single case study informed by data from semi-structured interviews and narratives with youth between the ages of 18 and 34 who are born and raised in South Africa to at least one former Mozambican refugee parent living in Bushbuckridge. Drawing from Crenshaw’s Intersectionality and Sen’s Capability approaches, this study significantly contributes to the existing body of knowledge on South to South migration by demonstrating how both approaches can be operationalized towards understanding complex experiences and capabilities of the disadvantaged group simultaneously. The subject of second-generation migrants is often under-researched in South African migration; thus, their perspectives have been marginalized in Social Science research.

Keywords: second-generation, Mozambican, migrant, youth, bushbuckridge

Procedia PDF Downloads 198

Authors: Tope Olubodun

Abstract:

Background: Family planning practices help individuals and couples avoid unwanted pregnancies, regulate intervals between pregnancies, and determine the number of children in the family. Family planning is an effective intervention for promoting maternal health, but its acceptability and utilization are impeded by many factors in Southwest Nigeria. Aim: This study was conducted to assess women’s knowledge and practice of family planning in two rural communities in Ogun State, Southwest Nigeria, and to determine factors associated with the utilization of family planning among these women. Methods: This was a cross-sectional study conducted among 561 women of reproductive age selected by multistage sampling. The data collection was done using interviewer-administered questionnaires. Data obtained were analyzed using IBM SPSS Statistics version 20. Frequencies were generated, and chi-square test was used to explore associations. The level of significance was set at 0.05. Result: The majority of the respondents were aware of family planning 410 (73.1%). The method most commonly known was male condom 348 (62.0%), then pills 276 (49.2%) and injectables 231(41.3%). The commonest sources of information on family planning were health workers 158 (26.8%), outreaches 162 (27.5%) and TV/radio 136 (23.1%). Respondents that had used family planning, however, only constituted forty–five percent. The methods commonly used were injectables 104 (39.2%) and pills 85 (32.1%). Reasons for choosing not to use family planning include the desire for more children 78 (26.3%), because spouse does not support family planning 56 (18.9%), fear of unbearable side effects 44 (14.9%), and poor knowledge of the methods of family planning as well as where the services can be obtained 39 (13.2%). There is a statistically significant association between age, ethnicity, education, occupation, average monthly income, and use of family planning. Conclusion: Campaigns that promote male involvement in family planning, use of family planning for child spacing, and dispelling of fears is recommended to improve the practice of family planning among such a group of women.

Keywords: family planning, rural, knowledge, practice

Procedia PDF Downloads 132

Authors: Yena Lee, Vassilis M. Charitopoulos, Karthik Thyagarajan, Ian Morris, Jose M. Pinto, Lazaros G. Papageorgiou

Abstract:

With globalisation, the need to have better coordination of production and distribution decisions has become increasingly important for industrial gas companies in order to remain competitive in the marketplace. In this work, we investigate a problem that integrates production, inventory, and routing decisions in a liquid oxygen supply chain. The oxygen supply chain consists of production facilities, external third-party suppliers, and multiple customers, including hospitals and industrial customers. The product produced by the plants or sourced from the competitors, i.e., third-party suppliers, is distributed by a fleet of heterogenous vehicles to satisfy customer demands. The objective is to minimise the total operating cost involving production, third-party, and transportation costs. The key decisions for production include production and inventory levels and product amount from third-party suppliers. In contrast, the distribution decisions involve customer allocation, delivery timing, delivery amount, and vehicle routing. The optimisation of the coordinated production, inventory, and routing decisions is a challenging problem, especially when dealing with large-size problems. Thus, we present a two-stage procedure to solve the integrated problem efficiently. First, the problem is formulated as a mixed-integer linear programming (MILP) model by simplifying the routing component. The solution from the first-stage MILP model yields the optimal customer allocation, production and inventory levels, and delivery timing and amount. Then, we fix the previous decisions and solve a detailed routing. In the second stage, we propose a column generation scheme to address the computational complexity of the resulting detailed routing problem. A case study considering a real-life oxygen supply chain in the UK is presented to illustrate the capability of the proposed models and solution method. Furthermore, a comparison of the solutions from the proposed approach with the corresponding solutions provided by existing metaheuristic techniques (e.g., guided local search and tabu search algorithms) is presented to evaluate the efficiency.

Keywords: production planning, inventory routing, column generation, mixed-integer linear programming

Procedia PDF Downloads 99

Authors: Jalil ur Rehman, Ramesh C, Tailor, Isa Khan, Jahanzeeb Ashraf, Muhammad Afzal, Geofferry S. Ibbott

Abstract:

The purpose of this analysis is to estimate secondary cancer risks after VMAT compared to other modalities of head and neck radiotherapy (IMRT, 3DCRT). Computer tomography (CT) scans of Radiological Physics Center (RPC) head and neck phantom were acquired with CT scanner and exported via DICOM to the treatment planning system (TPS). Treatment planning was done using four arc (182-178 and 180-184, clockwise and anticlockwise) for volumetric modulated arc therapy (VMAT) , Nine fields (200, 240, 280, 320,0,40,80,120 and 160), which has been commonly used at MD Anderson Cancer Center Houston for intensity modulated radiation therapy (IMRT) and four fields for three dimensional radiation therapy (3DCRT) were used. True beam linear accelerator of 6MV photon energy was used for dose delivery, and dose calculation was done with CC convolution algorithm with prescription dose of 6.6 Gy. Primary Target Volume (PTV) coverage, mean and maximal doses, DVHs and volumes receiving more than 2 Gy and 3.8 Gy of OARs were calculated and compared. Absolute point dose and planar dose were measured with thermoluminescent dosimeters (TLDs) and GafChromic EBT2 film, respectively. Quality Assurance of VMAT and IMRT were performed by using ArcCHECK method with gamma index criteria of 3%/3mm dose difference to distance to agreement (DD/DTA). PTV coverage was found 90.80 %, 95.80 % and 95.82 % for 3DCRT, IMRT and VMAT respectively. VMAT delivered the lowest maximal doses to esophagus (2.3 Gy), brain (4.0 Gy) and thyroid (2.3 Gy) compared to all other studied techniques. In comparison, maximal doses for 3DCRT were found higher than VMAT for all studied OARs. Whereas, IMRT delivered maximal higher doses 26%, 5% and 26% for esophagus, normal brain and thyroid, respectively, compared to VMAT. It was noted that esophagus volume receiving more than 2 Gy was 3.6 % for VMAT, 23.6 % for IMRT and up to 100 % for 3DCRT. Good agreement was observed between measured doses and those calculated with TPS. The averages relative standard errors (RSE) of three deliveries within eight TLD capsule locations were, 0.9%, 0.8% and 0.6% for 3DCRT, IMRT and VMAT, respectively. The gamma analysis for all plans met the ±5%/3 mm criteria (over 90% passed) and results of QA were greater than 98%. The calculations for maximal doses and volumes of OARs suggest that the estimated risk of secondary cancer induction after VMAT is considerably lower than IMRT and 3DCRT.

Keywords: RPC, 3DCRT, IMRT, VMAT, EBT2 film, TLD

Procedia PDF Downloads 491

Authors: Tadesse Melaku Abegaz, Akshaya Srikanth Bahagavathula, Abdulla Shehab Sheab, Asim Hassen

Abstract:

Objectives: Non-adherence and discontinuation of anticoagulant therapy lead to increased ischemic stroke risk and contributes to suboptimal outcomes of the anticoagulant treatment. This systematic review and meta-analysis were aimed to investigate the adherence to NOACs and adverse events in patients with AF. Methods: Original research articles conducted on patients with AF and using any NOACs (dabigatran, rivoraxaban and apixaban) reporting adherence for at least 35 days were included. Scientific databases including PubMed, Web of Science, and Google Scholar were searched using MeSH keywords to obtaining literature researched between 2008 to till June, 2016. Study characteristics, patient’s sociodemographic and clinical characteristics, medication adherence levels and bleeding events reported were recorded. Results: The overall sample size of the six studies is 1,640,157, with CHADS2 scores < 2 in 551 patients, CHADS2-VASc ≥ 2 in 62,232 AF patients. Three-forth [75.6% (95%CI= 66.5-84.8), p < 0.001] are adherent to NOACs. However, a higher rate [72.7% (62.5-82.9), p < 0.001] of adherence was observed with Dabigatran than Apixaban [59.9% (3.2-123.1), p=0.063] and Rivaroxaban [59.3% (38.7-80.0), p<0.001]. Sub-group analysis revealed that nearly 57% of the AF patients on NOACs have CHADS2 scores < 2 and 20% of these patients were non-adherent to NOACs. Overall bleeding events rate associated with NOACs non-adherent AF patients was found to be 7.5% (0.2-14.8), p=0.045. However, nearly 11.2% of AF patients experienced bleeding events were non-adherent to NOAC medications. A higher proportion of bleeding events were noticed with Dabigatran (14.7%). Conclusions: Adherence rates, while uniformly suboptimal, nevertheless varied considerably, lowest at 59.3% for rivaroxaban and 59.9% for apixaban, followed by dabigatran (75.6%). Overall bleeding events associated with NOACs rates were 7.5%. However, lower adherence to NOACs was associated with worse outcomes among patients with greater stroke risk.

Keywords: atrial fibrillation, bleeding events, meta-analysis, novel oral anticoagulants

Procedia PDF Downloads 324

Authors: Pilly Joseph Kagosi

Abstract:

The study aims at assessing challenges observed during implementation of participatory irrigation management (PIM) approach for food security in semi-arid areas of Tanzania. Data were collected through questionnaire, PRA tools, key informants discussion, Focus Group Discussion (FGD), participant observation and literature review. Data collected from questionnaire was analyzed using SPSS while PRA data was analyzed with the help of local communities during PRA exercise. Data from other methods were analyzed using content analysis. The study revealed that PIM approach has contribution in improved food security at household level due to involvement of communities in water management activities and decision making which enhanced availability of water for irrigation and increased crop production. However there were challenges observed during implementation of the approach including; minimum participation of beneficiaries in decision making during planning and designing stages, meaning inadequate devolution of power among scheme owners; Inadequate and lack of transparency on income expenditure in Water Utilization Associations’ (WUAs), water conflict among WUAs members, conflict between farmers and livestock keepers and conflict between WUAs leaders and village government regarding training opportunities and status; WUAs rules and regulation are not legally recognized by the National court and few farmers involved in planting trees around water sources. However it was realized that some of the mentioned challenges were rectified by farmers themselves facilitated by government officials. The study recommends that, the identified challenges need to be rectified for farmers to realize impotence of PIM approach as it was realized by other Asian countries.

Keywords: potentials of implementing participatory approach, challenges of participatory approach, irrigation management, Tanzania

Procedia PDF Downloads 287

Authors: Timea I. Hajnal-Jafari, Simonida S. Đurić, Dragana R. Stamenov

Abstract:

Microbial inoculants from the group of symbiotic-nitrogen-fixing rhizobia are well known and widely used in production of legumes. On the other hand, nonsymbiotic plant growth promoting rhizobacteria (PGPR) are not commonly used in practice. The objective of this study was to examine the effects of soybean inoculation with symbiotic and nonsymbiotic bacteria on plant growth and seed yield of soybean. Microbiological activity in rhizospheric soil was also determined. The experiment was set up using a randomized block system in filed conditions with the following treatments: control-no inoculation; treatment 1-Bradyrhizobium japonicum; treatment 2-Azotobacter sp.; treatment 3-Bacillus sp..In the flowering stage of growth (FS) the number of nodules per plant (NPP), root length (RL), plant height (PH) and weight (PW) were measured. The number of pod per plant (PPP), number of seeds per pod (SPP) and seed weight per plant (SWP) were recorded at the end of vegetation period (EV). Microbiological analyses of soil included the determination of total number of bacteria (TNB), number of fungi (FNG), actinomycetes (ACT) and azotobacters (AZB) as well as the activity of the dehydrogenase enzyme (DHA). The results showed that bacterial inoculation led to the formation of root nodules regardless of the treatments with statistically no significant difference. Strong nodulation was also present in control treatment. RL and PH were positively influenced by inoculation with Azotobacter sp. and Bacillus sp., respectively. Statistical analyses of the number of PPP, SPP, and SWP showed no significant differences among investigated treatments. High average number of microorganisms were determined in all treatments. Most abundant were TNB (log No 8,010) and ACT (log No 6,055) than FNG and AZB with log No 4,867 and log No 4,025, respectively. The highest DHA activity was measured in the FS of soybean in treatment 3. The application of nonsymbiotic bacteria in soybean production can alleviate initial plant growth and help the plant to better overcome different stress conditions caused by abiotic and biotic factors.

Keywords: bacteria, inoculation, soybean, microbial activity

Procedia PDF Downloads 133

Authors: Shian Guan, Marie Bourdin, Isabelle Trenque, Younes Messaddeq, Thierry Cardinal, Nicolas Penin, Issam Mjejri, Aline Rougier, Etienne Duguet, Stephane Mornet, Manuel Gaudon

Abstract:

At the interface of the studies performed by 3 Ph.D. students: Shian Guan (2017-2020), Marie Bourdin (2016-2019) and Isabelle Trenque (2012-2015), a single synthesis route: polyol-mediated process, was used with success for the preparation of different inorganic oxides. Both of these inorganic oxides were elaborated for their potential application as smart optical compounds. This synthesis route has allowed us to develop nanoparticles of zinc oxide, vanadium oxide or tungsten oxide. This route is with easy implementation, inexpensive and with large-scale production potentialities and leads to materials of high purity. The obtaining by this route of nanometric particles, however perfectly crystalline, has notably led to the possibility of doping these matrix materials with high doping ion concentrations (high solubility limits). Thus, Al3+ or Ga3+ doped-ZnO powder, with high doping rate in comparison with the literature, exhibits remarkable infrared absorption properties thanks to their high free carrier density. Note also that due to the narrow particle size distribution of the as-prepared nanometric doped-ZnO powder, the original correlation between crystallite size and unit-cell parameters have been established. Also, depending on the annealing atmosphere use to treat vanadium precursors, VO2, V2O3 or V2O5 oxides with thermochromic or electrochromic properties can be obtained without any impurity, despite the versatility of the oxidation state of vanadium. This is of more particular interest on vanadium dioxide, a relatively difficult-to-prepare oxide, whose first-order metal-insulator phase transition is widely explored in the literature for its thermochromic behavior (in smart windows with optimal thermal insulation). Finally, the reducing nature of the polyol solvents ensures the production of oxygen-deficient tungsten oxide, thus conferring to the nano-powders exotic colorimetric properties, as well as optimized photochromic and electrochromic behaviors.

Keywords: inorganic oxides, electrochromic, photochromic, thermochromic

Procedia PDF Downloads 205

Authors: Mulubrhan Berihu, Supratic Gupta, Zena Gebriel

Abstract:

Due to the design versatility, availability, and cost efficiency, concrete is continuing to be the most used construction material on earth. However, the production of Portland cement, the primary component of concrete mix is causing to have a serious effect on environmental and economic impacts. This shows there is a need to study using of supplementary cementitious materials (SCMs). The most commonly used supplementary cementitious materials are wastes and the use of these industrial waste products has technical, economical and environmental benefits besides the reduction of CO2 emission from cement production. The study aims to document the effect on strength property of concrete due to use of low cement by maximizing supplementary cementitious materials like fly ash or marble powder. Based on the different mix proportion of pozzolana and marble powder a range of mix design was formulated. The first part of the project is to study the strength of low cement concrete using fly ash replacement experimentally. The test results showed that using up to 85 kg/m3 of cement is possible for plain concrete works like hollow block concrete to achieve 9.8 Mpa and the experimental results indicates that strength is a function of w/b. In the second part a new set of mix design has been carried out with fly ash and marble powder to study the strength of both binary and ternary mixes. In this experimental study, three groups of mix design (c+FA, c+FA+m and c+m), four sets of mixes for each group were taken up. Experimental results show that c+FA has maintained the best strength and impermeability whereas c+m obtained less compressive strength, poorer permeability and split tensile strength. c+FA shows a big difference in gaining of compressive strength from 7 days to 28 days compression strength compared to others and this obviously shows the slow rate of hydration of fly ash concrete. As the w/b ratio increases the strength decreases significantly. At the same time higher permeability has been seen in the specimens which were tested for three hours than one hour.

Keywords: efficiency factor, cement content, compressive strength, mix proportion, w/c ratio, water permeability, SCMs

Procedia PDF Downloads 190

Authors: Jonathan K. Hill

Abstract:

The transportation networks throughout Africa remain the only transportation infrastructure system in the world that is attacked by terrorists at a high frequency, so the international community can learn from each attack. The targeting of transportation should be recognized as a direct attack against a civilian population, so the international community should work to better understand the types of attacks utilized, the types of improvised explosive device designs adapted to transportation targets, and the ways the various modes of transportation have been attacked throughout the continent. Some countries have seen grenade attacks that have resulted in only injuries, while some countries have experienced large vehicle bombings that have resulted in hundreds of injuries and numerous deaths. With insurgencies, explosive devices have been small, complex, and generally target an enemy of the insurgency. With terrorist bombings, the explosive devices have been large, brazen, and targeted at civilian populations. And, these civilian populations are easily targeted within the transportation system. The presentation provided by Assess Africa LLC is titled ‘Evolution of Bombings Against Transportation Infrastructure’ and covers improvised explosive device characteristics, how improvised explosive devices have been adapted to transportation targets in Africa, analyses recent incidents, and provides some advice for effective protective measures. A main component of the improvised explosive device characteristics portion of the presentation focuses on the link between explosive device components, the intelligence network, and the bomb-builder’s network. By understanding the components, how the use of various components can be linked to a terrorist group’s capabilities, and how the bomb-builder acquires materials, the analysis of improvised explosive device attacks takes on a new direction – one that focuses on defeating the network instead of merely reviewing incidents of the past.

Keywords: Africa, bombings, critical infrastructure protection, transportation security

Procedia PDF Downloads 407

Authors: Selen Demirtas Zorbaz, Ozlem Ulas

Abstract:

Examining the reasons of child behaviour problems has been one of the focus of psychology and related disciplines for so long. It can be said there is a lot of reasons of child behaviour problems and familial factors might be the leading ones. When taking into account the prevalence of the children having behaviour problems in Turkey, it can be said that it is important to carry out studies putting forward the reasons of behaviour problems. From this point of view, the aim of this study is to examine dissertations and thesis putting forward the relationship between problem behaviour of the children (12-year-old and younger) and teenagers (12-18 years old), and familial factors. For that purpose, 46 dissertations that were chosen according to the study criteria out of 141 dissertations scanned by using the keywords of ‘behaviour problems’ and ‘behaviour disorder’ at Higher Education Thesis Centre between the years of 1989 and 2016 have been taken into the scope of the study. ‘Thesis Examination Draft Form’ has been prepared for the purpose of being used for data collecting tool. For the analysis of the data, percentage, and frequency analysis methods have been used. When the results of these studies are evaluated on the whole, it is seen that all the dissertations and thesis done are descriptive study, and it was not encountered any studies designed as experimental. When looked at the distribution of dissertations by years, it is seen that the first thesis was done in 1989 and the most number of dissertations were done in the years of 2014 and 2016. When looked at the department in which the dissertations were done, it can be said that dissertations and thesis were done in many different fields of disciplines ranging from psychology and special education. In addition to this, when investigated the group taken into the scope of dissertations and thesis research, it is seen that the children mostly worked with are below the age of 12 and types of studies are master’s thesis. When the dissertations and thesis are examined by means of topics, it is seen that mostly-studied topics are demographic variables such as gender, whether the family is fragmented or not, education level of the family and the parents’ attitude. Obtained findings have been examined in the light of literature.

Keywords: family, child behaviour problem, dissertations, thesis

Procedia PDF Downloads 220

Authors: Mohammed Elghazy, Ahmed El Refai, Usama Ebead, Antonio Nanni

Abstract:

Rehabilitating corrosion-damaged reinforced concrete (RC) structures has been accomplished using various techniques such as steel plating, external post-tensioning, and external bonding of fiber reinforced polymer (FRP) composites. This paper reports on the use of an innovative technique to strengthen corrosion-damaged RC structures using fabric-reinforced cementitious matrix (FRCM) composites. FRCM consists of dry-fiber fabric embedded in cement-based matrix. Twelve large-scale RC beams were constructed and tested in flexural monotonic and fatigue loads. Prior to testing, ten specimens were subjected to accelerated corrosion process for 140 days leading to an average mass loss in the tensile steel bars of 18.8 %. Corrosion was restricted to the main reinforcement located in the middle third of the beam span. Eight corroded specimens were repaired and strengthened while two virgin and two corroded-unrepaired/unstrengthened beams were used as benchmarks for comparison purpose. The test parameters included the FRCM materials (Carbon-FRCM, PBO-FRCM), the number of FRCM plies, the strengthening scheme, and the type of loading (monotonic and fatigue). The effects of the pervious parameters on the flexural response, the mode of failure, and the fatigue life were reported. Test results showed that corrosion reduced the yield and ultimate strength of the beams. The corroded-unrepaired specimen failed to meet the provisions of the ACI-318 code for crack width criteria. The use of FRCM significantly increased the ultimate strength of the corroded specimen by 21% and 65% more than that of the corroded-unrepaired specimen. Corrosion significantly decreased the fatigue life of the corroded-unrepaired beam by 77% of that of the virgin beam. The fatigue life of the FRCM repaired-corroded beams increased to 1.5 to 3.8 times that of the corroded-unrepaired beam but was lower than that of the virgin specimen. The specimens repaired with U-wrapped PBO-FRCM strips showed higher fatigue life than those repaired with the end-anchored bottom strips having similar number of PBO-FRCM-layers. PBO-FRCM was more effective than Carbon-FRCM in restoring the fatigue life of the corroded specimens.

Keywords: corrosion, concrete, fabric-reinforced cementitious matrix (FRCM), fatigue, flexure, repair

Procedia PDF Downloads 285

Authors: Chloe Richards, Adrian Delgado Ollero, Yan Delaure, Fiona Regan

Abstract:

Growing concern about the natural environment has accelerated the search for non-toxic, but at the same time, economically reasonable, antifouling materials. Bioinspired surfaces, due to their nano and micro topographical antifouling capabilities, provide a hopeful approach to the design of novel antifouling surfaces. Biological organisms are known to have highly evolved and complex topographies, demonstrating antifouling potential, i.e. shark skin. Previous studies have examined the antifouling ability of topographic patterns, textures and roughness scales found on natural organisms. One of the mechanisms used to explain the adhesion of cells to a substrate is called attachment point theory. Here, the fouling organism experiences increased attachment where there are multiple attachment points and reduced attachment, where the number of attachment points are decreased. In this study, an attempt to characterize the microtopography of the common brill fish, Scophthalmus rhombus, was undertaken. Scophthalmus rhombus is a small flatfish of the family Scophthalmidae, inhabiting regions from Norway to the Mediterranean and the Black Sea. They reside in shallow sandy and muddy coastal areas at depths of around 70 – 80 meters. Six engineered surfaces (inspired by the Brill fish scale) produced by a 2-photon polymerization (2PP) process were evaluated for their potential as an antifouling solution for incorporation onto tidal energy blades. The micro-textures were analyzed for their AF potential under both static and dynamic laboratory conditions using two laboratory grown diatom species, Amphora coffeaeformis and Nitzschia ovalis. The incorporation of a surface topography was observed to cause a disruption in the growth of A. coffeaeformis and N. ovalis cells on the surface in comparison to control surfaces. This work has demonstrated the importance of understanding cell-surface interaction, in particular, topography for the design of novel antifouling technology. The study concluded that biofouling can be controlled by physical modification, and has contributed significant knowledge to the use of a successful novel bioinspired AF technology, based on Brill, for the first time.

Keywords: attachment point theory, biofouling, Scophthalmus rhombus, topography

Procedia PDF Downloads 86

Authors: Aaron Herve Mbwe Mbissik, Lotfi Khiari, Otmane Raji, Abdellatif Elghali, Abdelkarim Lajili, Muhammad Ouabid, Martin Jemo, Jean-Louis Bodinier

Abstract:

Potassium (K) is an essential macronutrient for plant growth, helping to regulate several physiological and metabolic processes. Evaporite-related potash salts, mainly sylvite minerals (K chloride or KCl), are the principal source of K for the fertilizer industry. However, due to the high potash-supply risk associated with its considerable price fluctuations and uneven geographic distribution for most agriculture-based developing countries, the development of alternative sources of fertilizer K is imperative to maintain adequate crop yield, reduce yield gaps, and food security. Alkaline Igneous rocks containing significant K-rich silicate minerals such as K feldspar are increasingly seen as the best alternative available. However, these rocks may require to be hydrothermally treatment to enhance the release of potassium. In this study, we evaluate the fertilizing capacity of raw and hydrothermally treated K-bearing silicate rocks from different areas in Morocco. The effectiveness of rock powders was tested in a greenhouse experiment using ryegrass (Lolium multiflorum) by comparing them to a control (no K added) and to a conventional fertilizer (muriate of potash: MOP or KCl). The trial was conducted in a randomized complete block design with three replications, and plants were grown on K-depleted soils for three growing cycles. To achieve our objective, in addition to the analysis of the muriate response curve and the different biomasses, we also examined three necessary coefficients, namely: the K uptake, then apparent K recovery (AKR), and the relative K efficiency (RKE). The results showed that based on the optimum economic rate of MOP (230 kg.K.ha⁻¹) and the optimum yield (44 000 kg.K.ha⁻¹), the efficiency of K silicate rocks was as high as that of MOP. Although the plants took up only half of the K supplied by the powdered rock, the hydrothermal material was found to be satisfactory, with a biomass value reaching the optimum economic limit until the second crop cycle. In comparison, the AKR of the MOP (98.6%) and its RKE in the 1st cycle were higher than our materials: 39% and 38%, respectively. Therefore, the raw and hydrothermal materials mixture could be an appropriate solution for long-term agronomic use based on the obtained results.

Keywords: K-uptake, AKR, RKE, K-bearing silicate rock, MOP

Procedia PDF Downloads 67

Authors: Massimiliano Condotta, Paolo Ruggeri, Chiara Scanagatta, Giovanni Borga

Abstract:

Architects and urban planners, when designing and renewing cities, have to face a complex set of problems, including the issues of noise and air pollution which are considered as hot topics (i.e., the Clean Air Act of London and the Soundscape definition). It is usually taken for granted that these problems go by together because the noise pollution present in cities is often linked to traffic and industries, and these produce air pollutants as well. Traffic congestion can create both noise pollution and air pollution, because NO₂ is mostly created from the oxidation of NO, and these two are notoriously produced by processes of combustion at high temperatures (i.e., car engines or thermal power stations). We can see the same process for industrial plants as well. What have to be investigated – and is the topic of this paper – is whether or not there really is a correlation between noise pollution and air pollution (taking into account NO₂) in urban areas. To evaluate if there is a correlation, some low-cost methodologies will be used. For noise measurements, the OpeNoise App will be installed on an Android phone. The smartphone will be positioned inside a waterproof box, to stay outdoor, with an external battery to allow it to collect data continuously. The box will have a small hole to install an external microphone, connected to the smartphone, which will be calibrated to collect the most accurate data. For air, pollution measurements will be used the AirMonitor device, an Arduino board to which the sensors, and all the other components, are plugged. After assembling the sensors, they will be coupled (one noise and one air sensor) and placed in different critical locations in the area of Mestre (Venice) to map the existing situation. The sensors will collect data for a fixed period of time to have an input for both week and weekend days, in this way it will be possible to see the changes of the situation during the week. The novelty is that data will be compared to check if there is a correlation between the two pollutants using graphs that should show the percentage of pollution instead of the values obtained with the sensors. To do so, the data will be converted to fit on a scale that goes up to 100% and will be shown thru a mapping of the measurement using GIS methods. Another relevant aspect is that this comparison can help to choose which are the right mitigation solutions to be applied in the area of the analysis because it will make it possible to solve both the noise and the air pollution problem making only one intervention. The mitigation solutions must consider not only the health aspect but also how to create a more livable space for citizens. The paper will describe in detail the methodology and the technical solution adopted for the realization of the sensors, the data collection, noise and pollution mapping and analysis.

Keywords: air quality, data analysis, data collection, NO₂, noise mapping, noise pollution, particulate matter

Procedia PDF Downloads 201

Authors: Asaiel Mubark Al Hadi

Abstract:

Background: A frequent anorectal condition known as hemorrhoids, sometimes known as piles, is characterized by a weakening of the anal cushion and the supporting tissue as well as spasms of the internal sphincter. Hemorrhoids are most frequently identified by painless bright red bleeding, prolapse, annoying grape-like tissue prolapse, itching, or a combination of symptoms. digital rectal examination (DRE) and anoscope are used to diagnose it. Constipation, a low-fiber diet, a high body- mass index (BMI), pregnancy, and a reduced physical activity are among the factors that are typically thought to increase the risk of hemorrhoids. Golighers is the most commonly used hemorrhoid classification scheme It is 4 degrees, which determines the degree of the event. The purpose of this study is to assess knowledge and awareness level of the causes and stages of Hemorrhoids in the public of Saudi Arabia. Method: This cross-sectional study was conducted in the Saudi Arabia between Oct 2022- Dec 2022. The study group included at least 384 aged above 18 years. The outcomes of this study were analyzed using the SPSS program using a pre-tested questionnaire. Results: The study included 1410 participants, 69.9% of them were females and 30.1% were males. 53.7% of participants aged 20- 30 years old. 17% of participants had hemorrhoids and 42% had a relative who had hemorrhoids. 42.8% of participants could identify stage 1 of hemorrhoids correctly, 44.7% identified stage 2 correctly, 46.7% identified stage 3 correctly and 58.1% identified stage 4 correctly. Only 28.9% of participants had high level of knowledge about hemorrhoids, 62.7% had moderate knowledge and 8.4% had low knowledge. Conclusion: In conclusion, Saudi general population has poor knowledge of hemorrhoids, their causes and their management approach. There was a significant association between knowledge scores of hemorrhoids with age, gender, residence area and employment.

Keywords: hemorrhoids, external hemorrhoid, internal hemorrhoid, anal fissure, hemorrhoid stages, prolapse, rectal bleeding

Procedia PDF Downloads 71

Authors: Omolara Lade, David Oloke

Abstract:

The approach to water management worldwide is currently in transition, with a shift from centralised infrastructures to greater consideration of decentralised technologies, such as rainwater harvesting (RWH). However, in Nigeria, implementation of sustainable water management, such as RWH systems, is inefficient and social, environmental and technical barriers, concerns and knowledge gaps exist, which currently restrict its widespread utilisation. This inefficiency contributes to water scarcity, water-borne diseases, and loss of lives and property due to flooding. Meanwhile, several RWH technologies have been developed to improve SWM through both demand and storm-water management. Such technologies involve the use of reinforced concrete cement (RCC) storage tanks, surface water reservoirs and ground-water recharge pits as storage systems. A framework was developed to assess the significance and extent of water management problems, match the problems with existing RWH-based solutions and develop a robust ready-to-use decision support tool that can quantify the costs and benefits of implementing several RWH-based storage systems. The methodology adopted was the mixed method approach, involving a detailed literature review, followed by a questionnaire survey of household respondents, Nigerian Architects and Civil Engineers and focus group discussion with stakeholders. 18 selection attributes have been defined and three alternatives have been identified in this research. The questionnaires were analysed using SPSS, excel and selected statistical methods to derive weightings of the attributes for the tool. Following this, three case studies were modelled using RainCycle software. From the results, the MDA model chose RCC tank as the most appropriate storage system for RWH.

Keywords: rainwater harvesting, modelling, hydraulic assessment, whole life cost, decision support system

Procedia PDF Downloads 361

Authors: S. Zeynep Siretioglu Girgin, Gizem Turna Cebeci

Abstract:

Turkey’s immigration policy is a controversial issue considering its legal, economic, social, and political and human rights dimensions. Formulation of an immigration policy goes hand in hand with political processes, where natives’ attitudes play a significant role. On the other hand, as was the case in Turkey, radical changes made in immigration policy or policies lacking transparency may cause severe reactions by the host society. The underlying discussion paper aims to analyze quantitatively the effects of the existing ‘open door’ immigration policy on the economic integration of Syrian refugees in Turkey, and on the perception of the native population of refugees. For the analysis, semi-structured in-depth interviews and focus group interviews have been conducted. After the introduction, a literature review is provided, followed by theoretical background on the explanation of natives’ attitudes towards immigrants. In the next section, a qualitative analysis of natives’ attitudes towards Syrian refugees is presented with the subtopics of (i) awareness, general opinions and expectations, (ii) open-door policy and management of the migration process, (iii) perception of positive and negative impacts of immigration, (iv) economic integration, and (v) cultural similarity. Results indicate that, natives concurrently have social, economic and security concerns regarding refugees, while difficulties regarding security and economic integration of refugees stand out. Socio-economic characteristics of the respondents, such as the educational level and employment status, are not sufficient to explain the overall attitudes towards refugees, while they can be used to explain the awareness of the respondents and the priority of the concerns felt.

Keywords: economic integration, immigration policy, integration policies, migrants, natives’ sentiments, perception, Syrian refugees, Turkey

Procedia PDF Downloads 343

Authors: Bajraktarevic Adnan, Djukic Branka, Sporisevic Lutvo, Krdzalic Zecevic Belma, Uzicanin Sajra, Hadzimuratovic Admir, Hadzimuratovic Hadzipasic Emina, Abduzaimovic Alisa, Kustric Amer, Suljevic Ismet, Serafi Ismail, Tahmiscija Indira, Khatib Hakam, Semic Jusufagic Aida, Haas Helmut, Vladicic Aleksandra, Aplenc Richard, Kadic Deovic Aida

Abstract:

Introduction: Joubert syndrome has an autosomal recessive pattern of inheritance. It is referred as the brain malfunctioning and caused due to the underdevelopment of the cerebellar vermis. Associated conditions involving the eye, the kidney, and ocular disease are well described. Aims: Research helps us better understand this diseases, Joubert syndrome and can lead to advances in diagnosis and treatment. Methods: Different several conditions have been described in which the molar tooth sign and characteristics of Joubert syndrome in ten different places in the world. Carrier testing and diagnosis are available if one of these gene mutations has been identified in an affected family member. Results: Authors have described eleven cases during twenty years of Joubert syndrome. It is a clinically and genetically heterogeneous group of disorders characterized by hypoplasia of the cerebellar vermis with the characteristic neuroradiologic molar tooth sign, and accompanying neurologic symptoms, including dysregulation of breathing pattern and developmental delay. We made confirmation of diagnosis in twin sisters with Joubert syndrome with renal anomalies. Ocular symptoms have existed in seven cases (63.64%) from total eleven. Eleven cases were different sex, five boys (45.45%) and six girls (54.44%). Conclusions: Joubert syndrome is inherited as an autosomal recessive genetic disorder with several features of the disease.

Keywords: Joubert syndrome, cerebellooculorenal syndrome, autosomal recessive genetic disorder (ARGD), children

Procedia PDF Downloads 266

Authors: Arefeh Arabaninezhad, Ali Fakher

Abstract:

Since the deterministic analysis methods fail to take system uncertainties into account, probabilistic and non-probabilistic methods are suggested. Geotechnical analyses are used to determine the stress and deformation caused by construction; accordingly, many input variables which depend on ground behavior are required for geotechnical analyses. The Random Set approach is an applicable reliability analysis method when comprehensive sources of information are not available. Using Random Set method, with relatively small number of simulations compared to fully probabilistic methods, smooth extremes on system responses are obtained. Therefore random set approach has been proposed for reliability analysis in geotechnical problems. In the present study, the application of random set method in reliability analysis of deep excavations is investigated through three deep excavation projects which were monitored during the excavating process. A finite element code is utilized for numerical modeling. Two expected ranges, from different sources of information, are established for each input variable, and a specific probability assignment is defined for each range. To determine the most influential input variables and subsequently reducing the number of required finite element calculations, sensitivity analysis is carried out. Input data for finite element model are obtained by combining the upper and lower bounds of the input variables. The relevant probability share of each finite element calculation is determined considering the probability assigned to input variables present in these combinations. Horizontal displacement of the top point of excavation is considered as the main response of the system. The result of reliability analysis for each intended deep excavation is presented by constructing the Belief and Plausibility distribution function (i.e. lower and upper bounds) of system response obtained from deterministic finite element calculations. To evaluate the quality of input variables as well as applied reliability analysis method, the range of displacements extracted from models has been compared to the in situ measurements and good agreement is observed. The comparison also showed that Random Set Finite Element Method applies to estimate the horizontal displacement of the top point of deep excavation. Finally, the probability of failure or unsatisfactory performance of the system is evaluated by comparing the threshold displacement with reliability analysis results.

Keywords: deep excavation, random set finite element method, reliability analysis, uncertainty

Procedia PDF Downloads 254

Authors: Samuele Abagnato, Lucia Rigamonti

Abstract:

Life-Cycle-Assessment (LCA) is an effective tool to quantify the environmental impacts of reuse models and recycling technologies for textiles. In this work, publications in the last ten years about LCA on textile waste are classified according to location, goal and scope, functional unit, waste composition, impact assessment method, impact categories, and sensitivity analysis. Twenty papers have been selected: 50% are focused only on recycling, 30% only on reuse, the 15% on both, while only one paper considers only the final disposal of the waste. It is found that reuse is generally the best way to decrease the environmental impacts of textiles waste management because of the avoided impacts of manufacturing a new item. In the comparison between a product made with recycled yarns and a product from virgin materials, in general, the first option is less impact, especially for the categories of climate change, water depletion, and land occupation, while for other categories, such as eutrophication or ecotoxicity, under certain conditions the impacts of the recycled fibres can be higher. Cultivation seems to have quite high impacts when natural fibres are involved, especially in the land use and water depletion categories, while manufacturing requires a remarkable amount of electricity, with its associated impact on climate change. In the analysis of the reuse processes, relevant importance is covered by the laundry phase, with water consumption and impacts related to the use of detergents. About the sensitivity analysis, it can be stated that one of the main variables that influence the LCA results and that needs to be further investigated in the modeling of the LCA system about this topic is the substitution rate between recycled and virgin fibres, that is the amount of recycled material that can be used in place of virgin one. Related to this, also the yield of the recycling processes has a strong influence on the results of the impact. The substitution rate is also important in the modeling of the reuse processes because it represents the number of avoided new items bought in place of the reused ones. Another aspect that appears to have a large influence on the impacts is consumer behaviour during the use phase (for example, the number of uses between two laundry cycles). In conclusion, to have a deeper knowledge of the impacts of a life-cycle approach of textile waste, further data and research are needed in the modeling of the substitution rate and of the use phase habits of the consumers.

Keywords: environmental impacts, life-cycle-assessment, textiles recycling, textiles reuse, textiles waste management

Procedia PDF Downloads 76

Authors: Sarah Snyder

Abstract:

Historians use the term ‘post-Holocaust’ to indicate the period from 1945 onward; however, for survivors of the Holocaust and their families, the Holocaust did not end in 1945. In fact, for some, it was just the beginning of their struggles. There are those who could not return to their homes, find loved ones, or fight off night terrors. Additionally, they continue to suffer from mental illness or physical disease stemming from the Holocaust. In order for historians to have a clearer understanding of the trauma survivors have endured, it is must to approach time differently. Trauma does not operate on a timeline and thereby, our understanding of ‘before,’ ‘during’ and ‘after’ are flawed. In order to convey this flaw, this study will examine memoirs of second and third-generation survivors and of child survivors. Within the second and third generation group, there are two types of generational memoirs that are scrutinized for this case study. The first being when a child or grandchild records the stories of their parent(s) or grandparent(s) without any of the second or third generation’s stories implicitly written. ‘Implicitly’ is used in the context that it is impossible for any writer to not impose at least some stylistic portion of themselves into writing, but the intent was to focus on the parent or grandparent. The other type of memoir is when they write their parent(s) or grandparent(s) story intertwined with their own story. Additionally, the child survivor has a unique role in memory and trauma studies. Much like later generations who write about the Holocaust but have not experienced the trauma firsthand, the child survivor must write about what they lived through and experienced but cannot remember without the assistance of research or other survivors. This study shows that survivors continue to demonstrate trauma-related paranoia. They fear experiencing another Holocaust. In their minds, they replay the horrors that they had experienced. A pilgrimage to a 20th century Europe, unlike one of the 1940s, causes uncertainty, confusion, and additional paranoia. It is through these findings that it becomes evident that historians must learn to study trauma without placing strict timelines that prevent understanding of how trauma impacts those who have experienced complex trauma.

Keywords: holocaust, generational, memoirs, trauma

Procedia PDF Downloads 192

Authors: Zhang Kehan, Du Luona

Abstract:

Wireless power transfer (WPT) systems have been widely investigated for advantages of convenience and safety compared to traditional plug-in charging systems. The research contents include impedance matching, circuit topology, transfer distance et al. for improving the efficiency of WPT system, which is a decisive factor in the practical application. What is more, coil structures such as spiral circular coil and helical coil with variable distance between two turns also have indispensable effects on the efficiency of WPT systems. This paper compares the efficiency of WPT systems utilizing spiral or helical coil with variable distance between two turns, and experimental results show that efficiency of spiral circular coil with an optimum distance between two turns is the highest. According to efficiency formula of resonant WPT system with series-series topology, we introduce M²/R₋₁ to measure the efficiency of spiral circular coil and helical coil WPT system. If the distance between two turns s is too close, proximity effect theory shows that the induced current in the conductor, caused by a variable flux created by the current flows in the skin of vicinity conductor, is the opposite direction of source current and has assignable impart on coil resistance. Thus in two coil structures, s affects coil resistance. At the same time, when the distance between primary and secondary coils is not variable, s can also make the influence on M to some degrees. The aforementioned study proves that s plays an indispensable role in changing M²/R₋₁ and then can be adjusted to find the optimum value with which WPT system achieves the highest efficiency. In actual application situations of WPT systems especially in underwater vehicles, miniaturization is one vital issue in designing WPT system structures. Limited by system size, the largest external radius of spiral circular coil is 100 mm, and the largest height of helical coil is 40 mm. In other words, the turn of coil N changes with s. In spiral circular and helical structures, the distance between each two turns in secondary coil is set as a constant value 1 mm to guarantee that the R2 is not variable. Based on the analysis above, we set up spiral circular coil and helical coil model using COMSOL to analyze the value of M²/R₋₁ when the distance between each two turns in primary coil sp varies from 0 mm to 10 mm. In the two structure models, the distance between primary and secondary coils is 50 mm and wire diameter is chosen as 1.5 mm. The turn of coil in secondary coil are 27 in helical coil model and 20 in spiral circular coil model. The best value of s in helical coil structure and spiral circular coil structure are 1 mm and 2 mm respectively, in which the value of M²/R₋₁ is the largest. It is obviously to select spiral circular coil as the first choice to design the WPT system for that the value of M²/R₋₁ in spiral circular coil is larger than that in helical coil under the same condition.

Keywords: distance between two turns, helical coil, spiral circular coil, wireless power transfer

Procedia PDF Downloads 330