Search results for: single minute exchange die

Authors: Anierudh Vishwanathan

Abstract:

This paper suggests a new design of the crankshaft system that would help to use a low revving engine for applications requiring the use of a high revving engine operating at the same power by converting the extra or unnecessary torque obtained from a low revving engine into angular velocity of the crankshaft of the engine hence, improve the fuel economy of the vehicle because of the fact that low revving engines run more effectively on lean air fuel mixtures accompanied with less wear and tear of the engine due to lesser rubbing of the piston rings with the cylinder walls. If the crankshaft with the proposed design is used in a low revving engine, then it will give the same torque and speed as that given by a high revving engine operating at the same power but the new engine will give better fuel economy. Hence the new engine will give the benefits of a low revving engine as well as a high revving engine. The proposed crankshaft design will be achieved by changing the design of the crankweb in such a way that it functions both as a counterweight as well as a helical gear that can transfer power to the secondary gear shaft which will be incorporated in the crankshaft system. The crankshaft and the secondary gear shaft will be operating at an overdrive ratio. The crankshaft will now be a two shaft system instead of a single shaft system. The newly designed crankshaft will be mounted on the bearings instead of being connected to the flywheel of the engine. This newly designed crankshaft will transmit power to the secondary shaft which will rotate the flywheel and then the rotary motion will be transmitted to the transmission system as usual. In this design, the concept of power transmission will be incorporated in the crankshaft system. In the paper, the crankshaft and the secondary shafts have been designed in such a way that at any instant of time only half the number of crankwebs will be meshed with the secondary shaft. For example, during one revolution of the crankshaft, if for the first half of revolution; first, second, seventh and eighth crankwebs are meshing with the secondary shaft then for the next half revolution, third, fourth, fifth and sixth crankwebs will mesh with the secondary shaft. This paper also analyses the proposed crankshaft design for safety against fatigue failure. Finite element analysis of the crankshaft has been done and the resultant stresses have been calculated.

Keywords: low revving, high revving, secondary shaft, partial meshing

Procedia PDF Downloads 269

Authors: Nikolaos Papadimas, Joanna Bennett, Amir Sakhaei, Timothy Dodwell

Abstract:

Composite modeling of consolidation processes is playing an important role in the process and part design by indicating the formation of possible unwanted prior to expensive experimental iterative trial and development programs. Composite materials in their uncured state display complex constitutive behavior, which has received much academic interest, and this with different models proposed. Errors from modeling and statistical which arise from this fitting will propagate through any simulation in which the material model is used. A general hyperelastic polynomial representation was proposed, which can be readily implemented in various nonlinear finite element packages. In our case, FEniCS was chosen. The coefficients are assumed uncertain, and therefore the distribution of parameters learned using Markov Chain Monte Carlo (MCMC) methods. In engineering, the approach often followed is to select a single set of model parameters, which on average, best fits a set of experiments. There are good statistical reasons why this is not a rigorous approach to take. To overcome these challenges, A hierarchical Bayesian framework was proposed in which population distribution of model parameters is inferred from an ensemble of experiments tests. The resulting sampled distribution of hyperparameters is approximated using Maximum Entropy methods so that the distribution of samples can be readily sampled when embedded within a stochastic finite element simulation. The methodology is validated and demonstrated on a set of consolidation experiments of AS4/8852 with various stacking sequences. The resulting distributions are then applied to stochastic finite element simulations of the consolidation of curved parts, leading to a distribution of possible model outputs. With this, the paper, as far as the authors are aware, represents the first stochastic finite element implementation in composite process modelling.

Keywords: data-driven , material consolidation, stochastic finite elements, surrogate models

Procedia PDF Downloads 146

Authors: Bremmy Laksono, Riksa Parikrama, Nur A. Rosyada, Willyanti Soewondo, Dadang S. H. Effendi, Eriska Rianti, Arlette S. Setiawan, Ine Sasmita, Risti S. Primanti, Erna Kurnikasari, Yunia Sribudiani

Abstract:

Down syndrome (DS) is a chromosomal abnormality characterised by complete 21 chromosome trisomy (classical or non-disjunction), or partial 21 chromosome trisomy (mosaicism), or chromosome rearrangement involving chromosome 21 (translocation). This study was carried out to describe the frequency of DS patients in a research institution in the city of Bandung, Indonesia. This descriptive study also provides a picture of the residential location and surrounding area of their dwellings. This study involved people with DS in various age whose chromosome were evaluated by conventional karyotyping method and FISH. Data were collected from 60 patients with DS from a total 150 patients during the period of September 2015 to August 2016 who were referred to Cell Culture and Cytogenetics Laboratory, Faculty of Medicine Universitas Padjadjaran, Indonesia. Results showed that the most common type of DS was non-disjunction (93%), followed by mosaicism (5%), no patient with translocation DS (0%), and a very rare type of tetrasomy 21 (2%). There were 39 males (65%) and 21 females (35%) of DS patient. Most of them live in suburban area beyond Bandung city (55%) while the rest live inside urban area of Bandung city (45%). They live mostly in dense area of greater Bandung area (65%) and only a few live in mid-density area (25%) and the least live in sparse populated area (10%). Their houses are mostly located in residential estate area (55%), nearby industrial area (37%), and around agricultural area (8%). Based on the study, it could be concluded that non-disjunction DS is the most common type. DS patients referred to the laboratory mostly came from dense residential zone in suburban area outside Bandung city. The low number of DS patients referred to the laboratory for chromosome analysis was the highlight to improve health service for people with genetic disorder. This study offered several information regarding area of DS patients’ residence and the condition of neighbourhood in Bandung city where they live as well.

Keywords: chromosome, descriptive, Down syndrome, prevalence

Procedia PDF Downloads 280

Authors: Min-Feng Hsieh

Abstract:

Nowadays, we are facing a highly competitive environment in which the situation for survival has come even more critical than ever before. The challenge we will be confronted with is no longer can be dealt with the single system of knowledge. The abilities we urgently need to acquire is something that can lead us to cross over the boundaries between different disciplines and take us to a neutral ground that gathers and integrates powers and intelligence that surrounds us. This paper aims at discussing how a trans-disciplinary design course organized by the College of Design at Chaoyang University can react to this modern challenge. By orchestrating an experimental course format and by developing a series of coaching strategies, a trans-disciplinary learning environment has been created and practiced in which students selected from five different departments, including Architecture, Interior Design, Visual Design, Industrial Design, Landscape and Urban Design, are encouraged to think outside their familiar knowledge pool and to learn with/from each other. In the course of implementing this program, a parallel research has been conducted alongside by adopting the theory and principles of Action Research which is a research methodology that can provide the course organizer emergent, responsive, action-oriented, participative and critically reflective insights for the immediate changes and amendments in order to improve the effect of teaching and learning experience. In the conclusion, how the learning and teaching experience of this trans-disciplinary design studio can offer us some observation that can help us reflect upon the constraints and division caused by the subject base curriculum will be pointed out. A series of concepts for course design and teaching strategies developed and implemented in this trans-disciplinary course are to be introduced as a way to promote learners’ self-motivated, collaborative, cross-disciplinary and student-centered learning skills. The outcome of this experimental course can exemplify an alternative approach that we could adopt in pursuing a remedy for dealing with the problematic issues of the current educational practice.

Keywords: course design, coaching strategy, subject base curriculum, trans-disciplinary

Procedia PDF Downloads 203

Authors: Eric Fang, Robert Chen, Ghim Song Chia, Bien Soo Tan

Abstract:

Objective and Rationale: Training of radiology residents hinges on practical, on-the-job training in all facets and modalities of diagnostic radiology. Although residency is structured to be comprehensive, clinical exposure depends on the case mix available locally and during the posting period. To supplement clinical training, there are several e-learning resources available to allow for greater exposure to radiological cases. The objective of this study was to survey residents and faculty on the usefulness of these e-learning resources. Methods: E-learning resources were shortlisted with input from radiology residents, Google search and online discussion groups, and screened by their purported focus. Twelve e-learning resources were found to meet the criteria. Both radiology residents and experienced radiology faculty were then surveyed electronically. The e-survey asked for ratings on breadth, depth, testing capability and user-friendliness for each resource, as well as for rankings for the top 3 resources. Statistical analysis was performed using SAS 9.4. Results: Seventeen residents and fifteen faculties completed an e-survey. Mean response rate was 54% ± 8% (Range: 14- 96%). Ratings and rankings were statistically identical between residents and faculty. On a 5-point rating scale, breadth was 3.68 ± 0.18, depth was 3.95 ± 0.14, testing capability was 2.64 ± 0.16 and user-friendliness was 3.39 ± 0.13. Top-ranked resources were STATdx (first), Radiopaedia (second) and Radiology Assistant (third). 9% of responders singled out R-ITI as potentially good but ‘prohibitively costly’. Statistically significant predictive factors for higher rankings are familiarity with the resource (p = 0.001) and user-friendliness (p = 0.006). Conclusion: A good e-learning system will complement on-the-job training with a broad case base, deep discussion and quality trainee evaluation. Based on our study on twelve e-learning resources, no single program fulfilled all requirements. The perception and use of radiology e-learning resources depended more on familiarity and user-friendliness than on content differences and testing capability.

Keywords: e-learning, medicine, radiology, survey

Procedia PDF Downloads 333

Authors: Beata Ślusarczyk, Sebastian Kot

Abstract:

In subjective terms, Polish SME sector occupies a prominent position in the national economic development, in which planning of the management strategies should be primarily based on identifying and meeting the innovation needs. As a research sample, there is chosen a printing sector of industry. SMEs share in printing sector in Poland is estimated at the level of 81% of all enterprises. In recent years, the printing industry achieved one of the highest levels of EU support in Poland. There is a relatively high increase in the development of technological innovations in equipment and the associated significant increase in production capacity. It can be also noticed that on average, every third enterprise belonging to the printing industry has implemented innovations, but not all of them effected in better economic results. Therefore, the aim of this article is to evaluate the impact of the implementation of innovation projects financed from the EU funds for performance of SMEs in the printing industry. As the results of research of EU funds co-financing effects on the development of innovation in the printing industry, it was specified that examined SMEs prefer to implement product innovation to receive a grant to the project at a level between 40% to 60%, the remaining part of the investment is usually covered with equity. The most common type of innovation had indicated a single implementation, related only to the change in process, technology, or organization. The relationship between variables of the EU funds and management of innovative activities was verified. It has been observed that the identified variables arising from the support in a form of the EU funds had a positive effect on the level of earned revenue, the increase in margin and in increase in employment as well. It was confirmed that the implemented innovations supported by the European funds have a positive impact on the performance of the printing companies. Although there is a risk that due to the decreasing demand for printing services such a high level of funding the companies in this sector will significantly increase competition in the long term, that may also contribute to the economic problems of the enterprises belonging to the analyzed branch.

Keywords: innovations, SMEs, performance, results

Procedia PDF Downloads 314

Authors: Hiroko Komatsu, Kaori Yagasaki

Abstract:

Background: Cancer-related cognitive impairment is a common problem seen in cancer patients undergoing chemotherapy. Physical activity may show beneficial effects on the cognitive function in such patients. Therefore, we have developed a self-directed home yoga program for cancer patients with cognitive symptoms during chemotherapy. This program involves a DVD presenting a combination of yoga courses based on patient preferences to be practiced at home. This study was performed to examine the feasibility of this program. In addition, we also examined changes in cognitive function and quality of life (QOL) in these patients participating in the program. Methods: This prospective feasibility study was conducted in a 500-bed general hospital in Tokyo, Japan. The study population consisted of breast cancer patients undergoing chemotherapy as the initial therapy. This feasibility study used a convenience sample with estimation of recruitment rate in a single facility with the availability of trained nurses and physicians to ensure safe yoga intervention. The aim of the intervention program was to improve cognitive function by means of both physical and mental activation via yoga, consisting of physical practice, breathing exercises, and meditation. Information on the yoga program was provided as a booklet, with an instructor-guided group yoga class during the orientation, and a self-directed home yoga program on DVD with yoga logs. Results: The recruitment rate was 44.7%, and the study population consisted of 18 women with a mean age of 43.9 years. This study showed high rates of retention, adherence, and acceptability of the yoga program. Improvements were only observed in the cognitive aspects of fatigue, and there were serious adverse events during the program. Conclusion: The self-directed home yoga program discussed here was both feasible and safe for breast cancer patients showing cognitive symptoms during chemotherapy. The patients also rated the program as useful, interesting, and satisfactory. Participation in the program was associated with improvements in cognitive fatigue but not cognitive function.

Keywords: yoga, cognition, breast cancer, chemotherapy, quality of life

Procedia PDF Downloads 257

Authors: P. T. Ngan

Abstract:

Purpose: The study aims to answer the question what are motivational conditions that have great influences on employees’ innovative work behaviors by investigating the case of SATAMANKULMA/ Anya Productions Ky in Kuopio, Finland. Design/methodology: The main methodology utilized was the qualitative single case study research, analysis was conducted with an adapted thematic content analysis procedure, created from empirical material that was collected through interviews, observation and document review. Findings: The paper highlights the significance of combining relevant synergistic extrinsic and intrinsic motivations into the organizational motivation system. The findings show that intrinsic drives are essential for the initiation phases while extrinsic drives are more important for the implementation phases of innovative work behaviors. The study also offers the IDEA motivation model-interpersonal relationships & networks, development opportunities, economic constituent and application supports as an ideal tool to optimize business performance. Practical limitations/ implications: The research was only conducted from the perspective of SATAMANKULMA/Anya Productions Ky, with five interviews, a few observations and with several reviewed documents. However, further research is required to include other stakeholders, such as the customers, partner companies etc. Also the study does not offer statistical validity of the findings; an extensive case study or a qualitative multiple case study is suggested to compare the findings and provide information as to whether IDEA model relevant in other types of firms. Originality/value: Neither the innovation nor the human resource management field provides a detailed overview of specific motivational conditions might use to stimulate innovative work behaviors of individual employees. This paper fills that void.

Keywords: employee innovative work behaviors, extrinsic motivation, intrinsic motivation, organizational innovativeness

Procedia PDF Downloads 267

Authors: Rohin Rameswarapu, Sameer Valsangkar

Abstract:

Background: Globally, musculoskeletal disorders are the largest single cause of work-related illnesses accounting for over 33% of all newly reported occupational illnesses. Risk factors for MSD need to be delineated to suggest means for amelioration. Material and methods: In this current cross-sectional study, the prevalence of MSDs among workers in an electrical company assembly line, the socio-demographic and job characteristics associated with MSD were obtained through a semi-structured questionnaire. A quantitative assessment of the physical risk factors through the Rapid Upper Limb Assessment (RULA) tool, and measurement of psychosocial risk factors through a Likert scale was obtained. Statistical analysis was conducted using Epi-info software and descriptive and inferential statistics including chi-square and unpaired t test were obtained. Results: A total of 263 workers consented and participated in the study. Among these workers, 200 (76%) suffered from MSD. Most of the workers were aged between 18–27 years and majority of the workers were women with 198 (75.2%) of the 263 workers being women. A chi square test was significant for association between male gender and MSD with a P value of 0.007. Among the MSD positive group, 4 (2%) had a grand score of 5, 10 (5%) had a grand score of 6 and 186 (93%) had a grand score of 7 on RULA. There were significant differences between the non-MSD and MSD group on five out of the seven psychosocial domains, namely job demand, job monotony, co-worker support, decision control and family and environment domains. Discussion: The current cross-sectional study demonstrates a high prevalence of MSD among assembly line works with inherent physical and psychosocial risk factors and recommends that not only physical risk factors, addressing psychosocial risk factors through proper ergonomic means is also essential to the well-being of the employee.

Keywords: musculoskeletal disorders, India, occupational health, Rapid Upper Limb Assessment (RULA)

Procedia PDF Downloads 349

Authors: Meera Shanker

Abstract:

Excellent education and financial need have encouraged Indian women to go out and work in well-paid and high-status occupations. In the era of cutthroat competition, women are expected to work hard to produce the desired result; hence, workload and expectations haveincreased. At home, they are anticipated to take care of family members, children, and household work. Women are stretching themselves mechanically to remain in the job competition and try to give their best at home. Consequentially, they are under tremendous pressure, stressed, and having issues related to physical-mental wellness. Mental healthcare is often ignored and not accepted due to a lack of awareness and cultural barriers. These further compounds the problem, resulting in decreased productivity in economic terms and an increase in stress-related physical-mental ailments. The main objective of the study was to find out the impact of stress on the physical-mental wellbeing of working women in India, along with their awareness and acceptability related to mental health. Six hundred and one woman working at various levels took part in this study, responding to the items related to stress and physical-mental illness. Finally, 21 items were retained under four meaningful factors measuring stress dimensions along with 17 items with three factors measuring physical-mental wellbeing. Confirmatory Factor Analysis (CFA), path analysis, in Structural Equation Modeling (SEM), was used to get a relationship, validity of the instruments. The psychometric properties of items and Cronbach’s Alpha reliabilities calculated for the subscales were relatively acceptable. The subscale correlations, regression, and path analysis of stress dimensions with physical-mental illness were found to be positive, indicating the growing stress among working women in India, which is impacting their physical-mental health. Single item analysis revealed that 77 percent of women have never visited psychologists. However, 70 percent of working women were not ready to seek the help of a psychologist.

Keywords: working women, stress, physical-mental well-being, confirmatory factor analysis

Procedia PDF Downloads 185

Authors: Sonia Besbes, Mahmoud El Hajem, Habib Ben Aissia, Jean Yves Champagne, Jacques Jay

Abstract:

In this work, we present a computational study for the characterization of the flow in a rectangular bubble column. To simulate the dynamic characteristics of the flow, a three-dimensional transient numerical simulations based on a coupled discrete phase model (DPM) and Volume of Fluid (VOF) model are performed. Modeling of bubble column reactor is often carried out under the assumption of a flat liquid surface with a degassing boundary condition. However, the dynamic behavior of the top surface surmounting the liquid phase will to some extent influence the meandering oscillations of the bubble plume. Therefore it is important to capture the surface behavior, and the assumption of a flat surface may not be applicable. So, the modeling approach needs to account for a dynamic liquid surface induced by the rising bubble plume. The volume of fluid (VOF) model was applied for the liquid and top gas which both interacts with bubbles implemented with a discrete phase model. This model treats the bubbles as Lagrangian particles and the liquid and the top gas as Eulerian phases with a sharp interface. Two-way coupling between Eulerian phases and Lagrangian bubbles are accounted for in a single set continuous phase momentum equation for the mixture of the two Eulerian phases. The effect of gas flow rate on the dynamic and time-averaged flow properties was studied. The time averaged liquid velocity field predicted from simulations and from our previous PIV measurements shows that the liquid is entrained up flow in the wake of the bubbles and down flow near the walls. The simulated and measured vertical velocity profiles exhibit a reasonable agreement looking at the minimum velocity values near the walls and the maximum values at the column center.

Keywords: bubble column, computational fluid dynamics (CFD), coupled DPM and VOF model, hydrodynamics

Procedia PDF Downloads 387

Authors: Mohammad Tofayel Ahmed, Seung Kook An

Abstract:

In contemporary research world, focus is more set on sustainable products and innovative processes. The global textile industries are putting tremendous effort to achieve a balance between economic development and ecological protection concurrently. The conservation of water sources and environment have become immensely significant issue in textile dyeing production. Accordingly, an attempt has been taken in this study to develop a process to dye polyester blend cotton without reduction clearing process and any extra wash off chemical by simple modification aiming at cost reduction and sustainability. A widely used combination of 60/40 cotton/polyester (c/p) single jersey knitted fabric of 30’s, 180 g/m² was considered for study. Traditionally, pretreatment is done followed by polyester part dyeing, reduction clearing and cotton part dyeing for c/p blend dyeing. But in this study, polyester part is dyed right away followed by pretreatment process and cotton part dyeing by skipping the reduction clearing process diametrically. The dyed samples of both traditional and modified samples were scrutinized by various color fastness tests, dyeing parameters and by consumption of water, steam, power, process time and total batch cost. The modified process in this study showed no necessity of reduction clearing process for polyester blend cotton dyeing. The key issue contributing to avoid the reduction clearing after polyester part dyeing has been the multifunctional effect of NaOH and H₂O₂ while pretreatment of cotton after polyester part dyeing. The results also revealed that the modified process could reduce the consumption of water, steam, power, time and cost remarkably. The bulk trial of modified process demonstrated the well exploitability to dye polyester blend cotton substrate ensuring all fastness and dyeing properties regardless of dyes category, blend ratio, color, and shade percentage thus making the process sustainable, eco-friendly and economical. Furthermore, the proposed method could be applicable to any cellulosic blend with polyester.

Keywords: cotton, dyeing, economical, polyester

Procedia PDF Downloads 188

Authors: Jasbir Arora, Indu Talwar, Daisy Sahni, Vidya Rattan

Abstract:

Introduction: Age estimation is a crucial step to build the identity of a person, both in case of deceased and alive. In adults, age can be estimated on the basis of six regressive (Attrition, Secondary dentine, Dentine transparency, Root resorption, Cementum apposition and Periodontal Disease) changes in teeth qualitatively using scoring system and quantitatively by micrometric method. The present research was designed to establish the reliability of qualitative (method 1) and quantitative (method 2) of age estimation among North Indians and to compare the efficacy of these two methods. Method: 250 single-rooted extracted teeth (18-75 yrs.) were collected from Department of Oral Health Sciences, PGIMER, Chandigarh. Before extraction, periodontal score of each tooth was noted. Labiolingual sections were prepared and examined under light microscope for regressive changes. Each parameter was scored using Gustafson’s 0-3 point score system (qualitative), and total score was calculated. For quantitative method, each regressive change was measured quantitatively in form of 18 micrometric parameters under microscope with the help of measuring eyepiece. Age was estimated using linear and multiple regression analysis in Gustafson’s method and Kedici’s method respectively. Estimated age was compared with actual age on the basis of absolute mean error. Results: In pooled data, by Gustafson’s method, significant correlation (r= 0.8) was observed between total score and actual age. Total score generated an absolute mean error of ±7.8 years. Whereas, for Kedici’s method, a value of correlation coefficient of r=0.5 (p<0.01) was observed between all the eighteen micrometric parameters and known age. Using multiple regression equation, age was estimated, and an absolute mean error of age was found to be ±12.18 years. Conclusion: Gustafson’s (qualitative) method was found to be a better predictor for age estimation among North Indians.

Keywords: forensic odontology, age estimation, North India, teeth

Procedia PDF Downloads 242

Authors: Georgia Kremmyda, Angelos Georgoulas, Yiannis Koumpouros, James T. Mottram

Abstract:

There is a growing interest in enhancing the creativity and problem-solving ability of engineering students by expanding their engagement to complex, interdisciplinary problems such as environmental issues, resilience to man-made and natural disasters, global health matters, water needs, increased energy demands, and other global humanitarian challenges. Tackling societal challenges requires knowledgeable and erudite engineers who can handle, combine, transform and create innovative, affordable and sustainable solutions. This view simultaneously complements and challenges current conceptions of an emerging educational movement that, almost without exception, are underpinned by calls for competitive economic growth and technological development. This article reveals a taxonomy of humanitarian attributes to be enabled to professional engineers, through reformed curricula and innovative pedagogies, which once implemented and integrated efficiently in higher engineering education, they will provide students and educators with opportunities to explore interdependencies and connections between resources, sustainable design, societal needs, and the natural environment and to critically engage with implicit and explicit facets of disciplinary identity. The research involves carrying out a study on (a) current practices, best practices and barriers in knowledge organisation, content, and hierarchy in graduate engineering programmes, (b) best practices associated with teaching and research in engineering education around the world, (c) opportunities inherent in general reforms of graduate engineering education and inherent in integrating the humanitarian context throughout engineering education programmes, and, (d) an overarching taxonomy of professional attributes for tackling humanitarian challenges. Research methods involve state-of-the-art literature review on engineering education and pedagogy to resource thematic findings on current status in engineering education worldwide, and qualitative research through three practice dialogue workshops, run in Asia (Vietnam, Indonesia and Bangladesh) involving a variety of national, international and local stakeholders (industries; NGOs, governmental organisations). Findings from this study provide evidence on: (a) what are the professional engineering attributes (skills, experience, knowledge) needed for tackling humanitarian challenges; (b) how we can integrate other disciplines and professions to engineering while defining the professional attributes of engineers who are capable of tackling humanitarian challenges. The attributes will be linked to those discipline(s) and profession(s) that are more likely to enforce the attributes (removing the assumption that engineering education as it stands at the moment can provide all attributes), and; (c) how these attributes shall be supplied; what kind of pedagogies or training shall take place beyond current practices. Acknowledgment: The study is currently in progress and is being undertaken in the framework of the project ENHANCE - ENabling Humanitarian Attributes for Nurturing Community-based Engineering (project No: 598502-EEP-1-2018-1-UK-EPPKA2-CBHE-JP (2018-2582/001-001), funded by the Erasmus + KA2 Cooperation for innovation and the exchange of good practices – Capacity building in the field of Higher Education.

Keywords: professional engineering attributes, engineering education, taxonomy, humanitarian challenges, humanitarian engineering

Procedia PDF Downloads 191

Authors: E. S. Umdu, Ilker Kahraman, Nurdan Yildirim, Levent Bilir

Abstract:

Algae-culture offers new applications in sustainable architecture with its continuous productive cycle, and a potential for high carbon dioxide capture. Microalgae itself has multiple functions such as carbon dioxide fixation, biomass production, oxygen generation and waste water treatment. Incorporating microalgae cultivation processes and systems to building design to utilize this potential is promising. Microalgae cultivation systems, especially closed photo bioreactors can be implemented as components in buildings. And these systems be accommodated in the façade of a building, or in other urban infrastructure in the future. Application microalgae bio-reactors of on building’s façade has the added benefit of acting as an effective insulation system, keeping out the heat of the summer and the chill of the winter. Furthermore, microalgae can give a dynamic appearance with a liquid façade that also works as an adaptive sunshade. Recently, potential of microalgae to use as a building component to reduce net energy demand in buildings becomes a popular topic and innovative design proposals and a handful of pilot applications appeared. Yet there is only a handful of examples in application and even less information on how these systems affect building energy behavior. Further studies on microalgae mostly focused on single application approach targeting either carbon dioxide utilization through biomass production or biofuel production. The main objective of this study is to investigate effects of design parameters of microalgae panel bio-reactors on light transmission characteristics and CO2 capture potential during growth of Nannochloropsis occulata sp. A maximum reduction of 18 ppm in CO2 levels of input air during the experiments with a % light transmission of 14.10, was achieved in 6 day growth cycles. Heat transfer behavior during these cycles was also inspected for possible façade applications.

Keywords: building façade, CO2 capture, light transmittance, microalgae

Procedia PDF Downloads 190

Authors: Bui Phuong Linh, Yuki Sakakibara, Ryuto Tanaka, Elizabeth H. Pigney, Taishi Hashiguchi

Abstract:

Non-alcoholic steatohepatitis (NASH) is a chronic liver disease, often associated with type II diabetes, which sometimes progresses to more serious conditions such as liver fibrosis and hepatocellular carcinoma (HCC). NASH has become an important health problem worldwide, buttherapeutic agents for NASH have not yet been approved, and animal models with high clinical correlation are required. TheSTAM™ mouse shows the same pathological progression as human NASH patients and has been widely used for both drug efficacy and basic research, such as lipid profiling and gut microbiota research. In this study, we analyzed the RNA-seq data of STAM™mice at each pathological stage (steatosis, steatohepatitis, liver fibrosis, and HCC) and examined the clinical correlation at the genetic level. NASH was induced in male mice by a single subcutaneous injection of 200 µg streptozotocin solution 2 days after birth and feeding with high fat dietafter 4 weeks of age. The mice were sacrificed and livers collected at 6, 8, 10, 12, 16, and 20 weeks of age. For liver samples, the left lateral lobe was snap frozen in liquid nitrogen and stored at -80˚C for RNA-seq analysis. Total RNA of the cells was isolated using RNeasy mini kit. The gene expression of the canonical pathways in NASH progression from steatosis to hepatocellular carcinoma were analyzed, such as immune system process, oxidation-reduction process, lipid metabolic process. Moreover, since it has been reported that genetic traits are involved in the development of NASH-HCC, we next analyzed the genetic mutations in the STAM™mice. The number of individuals showing mutations in Mtorinvolved in Insulin signaling increases as the disease progresses, especially in the liver cancer phase. These results indicated a clinical correlation of gene profiles in the STAM™mouse.

Keywords: steatosis, non-alcoholic steatohepatitis, fibrosis, hepatocellular carcinoma, RNA-seq

Procedia PDF Downloads 155

Authors: Igor Vishnevskyi

Abstract:

Introduction: The urinary bladder undergoes repeated strain during its working cycle, suggesting the presence of an efficient support system, force transmission, and mechanical amplification. The concept of a "hydrostatic skeleton" (HS) could contribute to our understanding of the functional relationships among bladder constituents. Methods: A multidisciplinary literature review was conducted to identify key features of the HS and to gather evidence supporting its applicability in urinary bladder biomechanics. The collected evidence was synthesized to propose a framework for understanding the potential hydrostatic properties of the urinary bladder based on existing knowledge and HS principles. Results: Our analysis revealed similarities in biomechanical features between living fluid-filled structures and the urinary bladder. These similarities include the geodesic arrangement of fibres, the role of enclosed fluid (urine) in force transmission, prestress as a determinant of stiffness, and the ability to maintain shape integrity during various activities. From a biomechanical perspective, urine may be considered an essential component of the bladder. The hydrostatic skeleton, with its autonomy and flexibility, may provide insights for researchers involved in bladder engineering. Discussion: The concept of a hydrostatic skeleton offers a holistic perspective for understanding bladder function by considering multiple mechanical factors as a single structure with emergent properties. Incorporating viewpoints from various fields on HS can help identify how this concept applies to live fluid-filled structures or organs and reveal its broader relevance to biological systems, both natural and artificial. Conclusion: The hydrostatic skeleton (HS) design principle can be applied to the urinary bladder. Understanding the bladder as a structure with HS can be instrumental in biomechanical modelling and engineering. Further research is required to fully elucidate the cellular and molecular mechanisms underlying HS in the bladder.

Keywords: hydrostatic skeleton, urinary bladder morphology, shape integrity, prestress, biomechanical modelling

Procedia PDF Downloads 78

Authors: Sandeep Vasaikar, Lary Obi

Abstract:

Rapid and discriminative genotyping methods are useful for determining the clonality of the isolates in nosocomial or household outbreaks. Multilocus sequence typing (MLST) is a nucleotide sequence-based approach for characterising bacterial isolates. The genetic diversity and the clinical relevance of the drug-resistant Klebsiella isolates from Mthatha are largely unknown. For this reason, prospective, experimental study of the molecular epidemiology of Klebsiella isolates from patients being treated in Mthatha over a three-year period was analysed. Methodology: PCR amplification and sequencing of the drug-resistance-associated genes, and multilocus sequence typing (MLST) using 7 housekeeping genes mdh, pgi, infB, FusAR, phoE, gapA and rpoB were conducted. A total of 32 isolates were analysed. Results: The percentages of multidrug-resistant (MDR), extensively drug-resistance (XDR) and pandrug-resistant (PDR) isolates were; MDR 65.6 % (21) and XDR and PDR with 0 % each. In this study, K. pneumoniae was 19/32 (59.4 %). MLST results showed 22 sequence types (STs) were identified, which were further separated by Maximum Parsimony into 10 clonal complexes and 12 singletons. The most dominant group was Klebsiella pneumoniae with 23/32 (71.8 %) isolates, Klebsiella oxytoca as a second group with 2/32 (6.25 %) isolates, and a single (3.1 %) K. varricola as a third group while 6 isolates were of unknown sequences. Conclusions/significance: A phylogenetic analysis of the concatenated sequences of the 7 housekeeping genes showed that strains of K. pneumoniae form a distinct lineage within the genus Klebsiella, with K. oxytoca and K. varricola its nearest phylogenetic neighbours. With the analysis of 7 genes were determined 1 K. variicola, which was mistakenly identified as K. pneumoniae by phenotypic methods. Two misidentifications of K. oxytoca were found when phenotypic methods were used. No significant differences were observed between ESBL blaCTX-M, blaTEM and blaSHV groups in the distribution of Sequence types (STs) or Clonal complexes (CCs).

Keywords: phylogenetic analysis, phylogeny, klebsiella phylogenetic, klebsiella

Procedia PDF Downloads 373

Authors: Antonia Harold-Barry, Eugene Dempsey

Abstract:

Background: The objective is to examine the survival and outcome of infants born under 26 weeks gestation in an Irish tertiary maternity hospital from 2007-2016 and to describe the survival and neurodevelopmental outcomes of these extremely preterm infants. Method: The population is 132 infants born at 23, 24, and 25 weeks in Cork University Maternity Hospital from 2007 to 2016. Ethical approval was granted by the Cork Clinical Research Ethics Committee. Patient details were obtained from the Vermont Oxford and Badger Networks. Survival rates and Bayley scores were calculated to assess neurodevelopmental outcomes. Statistical analysis with SPSS included frequencies, distributions, and comparisons between data from 2007-2011 and 2012-2016. Results: Overall survival rate was 63%. Of the surviving babies, 61% had Bayley scores calculated. Survival stood at 39% for delivery at 23 weeks, 50% at 24 weeks, and 83% at 25 weeks. The 2012 to 2016 cohort has shown further increases in survival, with 50% of babies at 23 weeks, 58% at 24 weeks, and 89% at 25 weeks. Corresponding figures for 2007-2011 are 20%, 39%, and 75%. Gestational age and incidence of periventricular leukomalacia were statistically significant, with a p-value of 0.022. Gestational age and delivery room deaths had a p-value of 0.025, as did gestational age and birth weight. A comparison of the two cohorts (2007-2011 and 2012-2016) with the administration of antenatal steroids showed a statistically significant p-value of 0.044. Conclusion: There is less morbidity and mortality in infants born at 25 than at 23 or 24 weeks. Survival of extremely premature infants has increased significantly over the past ten years. Survival rates with normal neurodevelopmental outcomes are comparable with international standards and reflect positive changes in attitude and practices in neonatal intensive care. This study will inform parents about the potential outcomes of extreme prematurity and policy regarding the management of extreme prematurity.

Keywords: extreme of viability, neurodevelopmental outcome, periventricular leukomalacia, prematurity

Procedia PDF Downloads 89

Authors: Hong Li, Haiyang Yu, Shiqing Cheng, Nai Cao, Zhiliang Shi

Abstract:

Unconventional resources have gradually become the main direction for oil and gas exploration and development. However, the productivity of gas wells, the level of water production, and the seepage law in tight fractured gas reservoirs are very different. These are the reasons why production prediction is so difficult. Firstly, a three-dimensional multi-scale fracture and multiphase mathematical model based on an embedded discrete fracture model (EDFM) is established. And the material balance method is used to calculate the water body multiple according to the production performance characteristics of water-producing gas well. This will help construct a 'virtual water body'. Based on these, this paper presents a numerical simulation process that can adapt to different production modes of gas wells. The research results show that fractures have a double-sided effect. The positive side is that it can increase the initial production capacity, but the negative side is that it can connect to the water body, which will lead to the gas production drop and the water production rise both rapidly, showing a 'scissor-like' characteristic. It is worth noting that fractures with different angles have different abilities to connect with the water body. The higher the angle of gas well development, the earlier the water maybe break through. When the reservoir is a single layer, there may be a stable production period without water before the fractures connect with the water body. Once connected, a 'scissors shape' will appear. If the reservoir has multiple layers, the gas and water will produce at the same time. The above gas-water relationship can be matched with the gas well production date of the Xujiahe gas reservoir in the Sichuan Basin. This method is used to predict the productivity of a well with hydraulic fractures in this gas reservoir, and the prediction results are in agreement with on-site production data by more than 90%. It shows that this research idea has great potential in the productivity prediction of water-producing gas wells. Early prediction results are of great significance to guide the design of development plans.

Keywords: EDFM, multiphase, multilayer, water body

Procedia PDF Downloads 193

Authors: Walid Ibrahim, Abdul Kasem, Sudeendra Doddi, Ilaria Giono, Tareq Sabagh, Muhammad Ammar, Nermin Osman

Abstract:

Background: wire-guided localization (WL) is the most widely used method for the localization of non-palpable breast lesions. SAVI SCOUT occult lesion localization (SSL) is a new technique in breast-conservative surgery. SSL has the potential benefit of improving radiology workflow as well as accurate localization. Purpose: The purpose of this study is to compare the breast tissue specimen volume and weight and margin excision between WL and SSL. Materials and methods: A single institution retrospective analysis of 377 female patients who underwent wide local breast excision with SAVI SCOUT and or wire-guided technique between 2018 and 2021 in a UK University teaching hospital. Breast department. Breast tissue specimen volume and weight, and margin excision have been evaluated in the three groups of different localization. Results: Three hundred and seventy-seven patients were studied. Of these, 261 had wire localization, 88 had SCOUT and 28 had dual localization techniques. Tumor size ranged from 1 to 75mm (Median 20mm). The pathology specimen weight ranged from 1 to 466gm (Median 46.8) and the volume ranged from 1.305 to 1560cm³ (Median 106.32 cm³). SCOUT localization was associated with a significantly low specimen weight than wire or the dual technique localization (Median 41gm vs 47.3gm and 47gm, p = 0.029). SCOUT was not associated with better specimen volume with a borderline significance in comparison to wire and combined techniques (Median 108cm³ vs 105cm³ and 105cm³, p = 0.047). There was a significant correlation between tumor size and pathology specimen weight in the three groups. SCOUT showed a better >2mm safety margin in comparison to the other 2 techniques (p = 0.031). Conclusion: Preoperative SCOUT localization is associated with better specimen weight and better specimen margin. SCOUT did not show any benefits in terms of specimen volume which may be due to difficulty in getting the accurate specimen volume due to the irregularity of the soft tissue specimen.

Keywords: scout, wire, localization, breast

Procedia PDF Downloads 110

Authors: Rita Emília Szabó, Róbert Polanek, Tünde Tőkés, Zoltán Szabó, Szabolcs Czifrus, Katalin Hideghéty

Abstract:

Purpose: Several feature of zebrafish are making them amenable for investigation on therapeutic approaches such as ionizing radiation. The establishment of zebrafish model for comprehensive radiobiological research stands in the focus of our investigation, comparing the radiation effect curves of neutron and photon irradiation. Our final aim is to develop an appropriate vertebrate model in order to investigate the relative biological effectiveness of laser driven ionizing radiation. Methods and Materials: After careful dosimetry series of viable zebrafish embryos were exposed to a single fraction whole-body neutron-irradiation (1,25; 1,875; 2; 2,5 Gy) at the research reactor of the Technical University of Budapest and to conventional 6 MeV photon beam at 24 hour post-fertilization (hpf). The survival and morphologic abnormalities (pericardial edema, spine curvature) of each embryo were assessed for each experiment at 24-hour intervals from the point of fertilization up to 168 hpf (defining the dose lethal for 50% (LD50)). Results: In the zebrafish embryo model LD50 at 20 Gy dose level was defined and the same lethality were found at 2 Gy dose from the reactor neutron beam resulting RBE of 10. Dose-dependent organ perturbations were detected on macroscopic (shortening of the body length, spine curvature, microcephaly, micro-ophthalmia, micrognathia, pericardial edema, and inhibition of yolk sac resorption) and microscopic (marked cellular changes in skin, cardiac, gastrointestinal system) with the same magnitude of dose difference. Conclusion: In our observations, we found that zebrafish embryo model can be used for investigating the effects of different type of ionizing radiation and this system proved to be highly efficient vertebrate model for preclinical examinations.

Keywords: ionizing radiation, LD50, relative biological effectiveness, zebrafish embryo

Procedia PDF Downloads 309

Authors: Min-Tao Hsu

Abstract:

This study aims to explore the lived experiences of women with breast cancer, including their life world of illness and their adaptation to breast cancer. Breast cancer is not only a potentially lethal disease, but also a disease that may lead to many irreversible changes for female patients. Especially, in a culture where the wholeness is pursuit as an essential value, the sickness and/or broken body bring great challenge of life. Based on holism and symbolic interactionism, this study used interpretive ethnography including in-depth interviews and participant observations to collect the narrative of women with breast cancer concerning their illness experience. In addition, this study used Agar’s hermeneutic cycle to analyze data. The average age of 35 participants was 54.2. A total of 15 patients were within 2 years of onset, 5 patients were within 2-5 years of the treatment observation period, and 15 patients suffered from breast cancer for more than 5 years. The average age of onset was 50.4. Result: The main storyline of the life world of illness is ‘breast cancer is a turning point of life.’ Loss of breast was in terms of ‘no more a woman’ in Taiwanese culture. Two young women, one in her newly wedded and another right before marry, were divorced and cancelled wedding right after being diagnosed. All of them addressed that they have a ‘broken body.’ Single women accounted that they won’t marry for not being humiliated and most of married women said they never show female body in front of her husband or partner even in intimacy encounter. Three common themes were discovered: 1) new self and new identity; 2) new social relationships and new me; 3) new body and new life. The intertwining bodies, illness, selves, suffering, and medical treatments of female patients were observed. More, the recovery, of cause, was happened when new self, relationship, and new body were generated. Their identity to be a woman and a wife is shattered and their life is urged into another facet. For helping them to recovery from such situation, building a new identity and new social fabric on the new body need to be included in nursing care plan.

Keywords: breast cancer, illness narrative, world of illness, self-healing, interpretive ethnography

Procedia PDF Downloads 334

Authors: Lidia Kowalska, Edward Arseniuk

Abstract:

Glume and leaf blotch is a disease of wheat caused by necrotrophic fungus Parastagonospora nodorum. It is a serious pathogen in many wheat-growing areas throughout the world. Use of resistant cultivars is the most effective and economical means to control the above-mentioned disease. Plant breeders and pathologists have worked intensively to incorporate resistance to the pathogen in new cultivars. Conventional methods of breeding for resistance can be supported by using the biotechnological ones, i.e., somatic embryogenesis and androgenesis. Therefore, an effort was undertaken to compare genetic variation in P. nodorum resistance among winter wheat somaclones, dihaploids and conventional varieties. For the purpose, a population of 16 somaclonal and 4 dihaploid wheat lines from six crosses were used to assess their resistance to P. nodorum under field conditions. Lines were grown in disease-free (fungicide protected) and inoculated micro plots in 2 replications of a split-plot design in a single environment. The plant leaves were inoculated with a mixture of P. nodorum isolates three times. Spore concentrations were adjusted to 4 x 10⁶ of viable spores per one milliliter. The disease severity was rated on a scale, where > 90% – susceptible, < 10% - resistant. Disease ratings of plant leaves showed statistically significant differences among all lines tested. Higher resistance to P. nodorum was observed more often on leaves of somaclonal lines than on dihaploid ones. On average, disease, severity reached 15% on leaves of somaclones and 30% on leaves of dihaploids. Some of the genotypes were showing low leaf infection, e.g. dihaploid D-33 (disease severity 4%) and a somaclone S-1 (disease severity 2%). The results from this study prove that dihaploid and somaclonal variation might be successfully used as an additional source of wheat resistance to the pathogen and it could be recommended to use in commercial breeding programs. The reported results prove that biotechnological methods may effectively be used in breeding for disease resistance of wheat to fungal necrotrophic pathogens.

Keywords: glume and leaf blotch, somaclonal, androgenic variation, wheat, resistance breeding

Procedia PDF Downloads 120

Authors: S M Abdus Sattar

Abstract:

Introduction: The tourism industry is a vital component of economies, providing opportunities for economic growth and cultural exchange. At the heart of this industry lies the concept of hospitality. Tourism refers to the activity of traveling for leisure or business and hospitality refers to the welcoming, amenities and providing of services to guests in the travel and accommodation industries. Tourism is one of the fastest growing industries in the world today. Objectives: The most important objective of Tourism and Hospitality study are: To assess different aspects, To identify the reasons, To analyze the contribution in GDP of Bangladesh, To identify importances of hospitality, To identify challenges, To Development of leadership characteristics, communication, teamwork skill, customer service and problem-solving, To provide welcoming treatment to guests, offering accommodation, food, transportation and entertainment services to ensure guests feel safe and comfortable away from home, To explore future prospects in Bangladesh and To suggests some recommendations for development of these sector. Methodology: Statistical method has been adopted in this study. Common characteristics of the people of particular area are found out. Tourism data is collected through various methods, such as surveys, interviews, visitor registration, travel agency records, hotel bookings, transport ticketing systems, online platforms, social media, Bangladesh Tourism Corporation, World Travel and Tourism Council, Quantitative and qualitative research methods are used while collecting and analyzing data. Findings: Tourism and Hospitality focuses on marketing, management, attractions, recreation events, travel related services, lodging, operations of restaurants and food services. Tourism offers great opportunities for emerging economies and developing countries. It creates jobs, strengthens the local economy, contributes to local infrastructure development, can help to conserve the natural environment, cultural assets, traditions, reduce poverty and inequality. The hospitality industry contributes to the economy of a country by employing its human resources. It generates new employment, contributing to the Gross Domestic Product (GDP) of a country. Around 330 million people were employed in the Tourism and Hospitality sector in globally. Tourism and Hospitality industry is creating high tax revenues. Tourism is a rising industry in Bangladesh. Studying hospitality can also help develop a range of essential skills that are valuable in any industry. Conclusion: As the conclusion, tourism industry is focused on providing quality attractions and events in order to entice tourists to come. The hospitality industry provides the good service for client. Hospitality and Tourism are closely related. Hospitality built up the relationship between host and guest. The importance of hospitality in tourism industry is immense. The Tourism and Hospitality industry is an important contributor to Bangladesh's economy. It is necessary to develop the Tourism infrastructure, maintain tourist destinations, railway stations, airports, rest house, hotels and improve the quality of services.

Keywords: tourism, hospitality, GDP, employment, economy

Procedia PDF Downloads 27

Authors: Amit Kumar Happy

Abstract:

This paper is motivated by the importance of multi-sensor image fusion with a specific focus on infrared (IR) and visual image (VI) fusion for various applications, including military reconnaissance. Image fusion can be defined as the process of combining two or more source images into a single composite image with extended information content that improves visual perception or feature extraction. These images can be from different modalities like visible camera & IR thermal imager. While visible images are captured by reflected radiations in the visible spectrum, the thermal images are formed from thermal radiation (infrared) that may be reflected or self-emitted. A digital color camera captures the visible source image, and a thermal infrared camera acquires the thermal source image. In this paper, some image fusion algorithms based upon multi-scale transform (MST) and region-based selection rule with consistency verification have been proposed and presented. This research includes the implementation of the proposed image fusion algorithm in MATLAB along with a comparative analysis to decide the optimum number of levels for MST and the coefficient fusion rule. The results are presented, and several commonly used evaluation metrics are used to assess the suggested method's validity. Experiments show that the proposed approach is capable of producing good fusion results. While deploying our image fusion algorithm approaches, we observe several challenges from the popular image fusion methods. While high computational cost and complex processing steps of image fusion algorithms provide accurate fused results, they also make it hard to become deployed in systems and applications that require a real-time operation, high flexibility, and low computation ability. So, the methods presented in this paper offer good results with minimum time complexity.

Keywords: image fusion, IR thermal imager, multi-sensor, multi-scale transform

Procedia PDF Downloads 115

Authors: Hossein Bazmara, Kaamran Raahemifar, Mostafa Sefidgar, Madjid Soltani

Abstract:

Angiogenesis is formation of new blood vessels from existing vessels. Due to flow of blood in vessels, during angiogenesis, blood flow plays an important role in regulating the angiogenesis process. Multiple mathematical models of angiogenesis have been proposed to simulate the formation of the complicated network of capillaries around a tumor. In this work, a multi-scale model of angiogenesis is developed to show the effect of blood flow on capillaries and network formation. This model spans multiple temporal and spatial scales, i.e. intracellular (molecular), cellular, and extracellular (tissue) scales. In intracellular or molecular scale, the signaling cascade of endothelial cells is obtained. Two main stages in development of a vessel are considered. In the first stage, single sprouts are extended toward the tumor. In this stage, the main regulator of endothelial cells behavior is the signals from extracellular matrix. After anastomosis and formation of closed loops, blood flow starts in the capillaries. In this stage, blood flow induced signals regulate endothelial cells behaviors. In cellular scale, growth and migration of endothelial cells is modeled with a discrete lattice Monte Carlo method called cellular Pott's model (CPM). In extracellular (tissue) scale, diffusion of tumor angiogenic factors in the extracellular matrix, formation of closed loops (anastomosis), and shear stress induced by blood flow is considered. The model is able to simulate the formation of a closed loop and its extension. The results are validated against experimental data. The results show that, without blood flow, the capillaries are not able to maintain their integrity.

Keywords: angiogenesis, endothelial cells, multi-scale model, cellular Pott's model, signaling cascade

Procedia PDF Downloads 425

Authors: Sebastien Relave, Christophe Desrayaud, Aurelien Vilani, Alexey Sova

Abstract:

Laser beam melting (LBM) is an additive manufacturing process that enables complex 3D parts to be designed. This process is now commonly employed for various applications such as chemistry or energy, requiring the use of stainless steel grades. LBM can offer comparable and sometimes superior mechanical properties to those of wrought materials. However, we observed an anisotropic microstructure which results from the process, caused by the very high thermal gradients along the building axis. This microstructure can be harmful depending on the application. For this reason, control and prediction of the microstructure are important to ensure the improvement and reproducibility of the mechanical properties. This study is focused on the 316L SS grade and aims at understanding the solidification and transformation mechanisms during process. Experiments to analyse the nucleation and growth of the microstructure obtained by the LBM process according to several conditions. These samples have been designed on different type of support bulk and lattice. Samples are produced on ProX DMP 200 LBM device. For the two conditions the analysis of microstructures, thanks to SEM and EBSD, revealed a single phase Austenite with preferential crystallite growth along the (100) plane. The microstructure was presented a hierarchical structure consisting columnar grains sizes in the range of 20-100 µm and sub grains structure of size 0.5 μm. These sub-grains were found in different shapes (columnar and cellular). This difference can be explained by a variation of the thermal gradient and cooling rate or element segregation while no sign of element segregation was found at the sub-grain boundaries. A high dislocation concentration was observed at sub-grain boundaries. These sub-grains are separated by very low misorientation walls ( < 2°) this causes a lattice of curvature inside large grain. A discussion is proposed on the occurrence of these microstructures formation, in regard of the LBM process conditions.

Keywords: selective laser melting, stainless steel, microstructure

Procedia PDF Downloads 157

Authors: Suresh Hettiarachchi, Conrad Wasko, Ashish Sharma

Abstract:

The ever changing and expanding urban landscape increases the stress on urban systems to support and maintain safe and functional living spaces. Flooding presents one of the more serious threats to this safety, putting a larger number of people in harm’s way in congested urban settings. Climate change is adding to this stress by creating a dichotomy in the urban flood response. On the one hand, climate change is causing storms to intensify, resulting in more destructive, rarer floods, while on the other hand, longer dry periods are decreasing the severity of more frequent, less intense floods. This variability is creating a need to be more agile and innovative in how we design for and manage urban flooding. Here, we argue that to cope with this challenge climate change brings, we need to move towards urban flood management through resilience rather than flood prevention. We also argue that dealing with the larger variation in flood response to climate change means that we need to look at flooding from all aspects rather than the single-dimensional focus of flood depths and extents. In essence, we need to rethink how we manage flooding in the urban space. This change in our thought process and approach to flood management requires a practical way to assess and quantify resilience that is built into the urban landscape so that informed decision-making can support the required changes in planning and infrastructure design. Towards that end, we propose a Simple Urban Flood Resilience Index (SUFRI) based on a robust definition of resilience as a tool to assess flood resilience. The application of a simple resilience index such as the SUFRI can provide a practical tool that considers urban flood management in a multi-dimensional way and can present solutions that were not previously considered. When such an index is grounded on a clear and relevant definition of resilience, it can be a reliable and defensible way to assess and assist the process of adapting to the increasing challenges in urban flood management with climate change.

Keywords: urban flood resilience, climate change, flood management, flood modelling

Procedia PDF Downloads 49

Authors: Jean Berger, Mohamed Barkaoui

Abstract:

Discrete search path planning in time-constrained uncertain environment relying upon imperfect sensors is known to be hard, and current problem-solving techniques proposed so far to compute near real-time efficient path plans are mainly bounded to provide a few move solutions. A new information-theoretic –based open-loop decision model explicitly incorporating false alarm sensor readings, to solve a single agent military logistics search-and-delivery path planning problem with anticipated feedback is presented. The decision model consists in minimizing expected entropy considering anticipated possible observation outcomes over a given time horizon. The model captures uncertainty associated with observation events for all possible scenarios. Entropy represents a measure of uncertainty about the searched target location. Feedback information resulting from possible sensor observations outcomes along the projected path plan is exploited to update anticipated unit target occupancy beliefs. For the first time, a compact belief update formulation is generalized to explicitly include false positive observation events that may occur during plan execution. A novel genetic algorithm is then proposed to efficiently solve search path planning, providing near-optimal solutions for practical realistic problem instances. Given the run-time performance of the algorithm, natural extension to a closed-loop environment to progressively integrate real visit outcomes on a rolling time horizon can be easily envisioned. Computational results show the value of the approach in comparison to alternate heuristics.

Keywords: search path planning, false alarm, search-and-delivery, entropy, genetic algorithm

Procedia PDF Downloads 360