Search results for: Huseyin Gunerhan

Authors: Asli Tiktas, Huseyin Gunerhan, Arif Hepbasli

Abstract:

Solar energy, with its abundant and clean features, is one of the prominent renewable energy sources in multigeneration energy systems where various outputs, especially power generation, are produced together. In the literature, concentrated solar energy systems, which are an expensive technology, are mostly used in solar power plants where medium-high capacity production outputs are achieved. In addition, although different methods have been developed and proposed for solar energy-supported integrated power generation systems by different investigators, absorption technology, which is one of the key points of the present study, has been used extensively in cooling systems in these studies. Unlike these common uses mentioned in the literature, this study designs a system in which a flat plate solar collector (FPSC), Rankine cycle, absorption heat transformer (AHT), and cooling systems (ACS) are integrated. The system proposed within the scope of this study aims to produce medium-high-capacity electricity, heating, and cooling outputs using a technique different from the literature, with lower production costs than existing systems. With the proposed integrated system design, the average production costs based on electricity, heating, and cooling load production for similar scale systems are 5-10% of the average production costs of 0.685 USD/kWh, 0.247 USD/kWh, and 0.342 USD/kWh. In the proposed integrated system design, this will be achieved by increasing the outlet temperature of the AHT and FPSC system first, expanding the high-temperature steam coming out of the absorber of the AHT system in the turbine up to the condenser temperature of the ACS system, and next directly integrating it into the evaporator of this system and then completing the AHT cycle. Through this proposed system, heating and cooling will be carried out by completing the AHT and ACS cycles, respectively, while power generation will be provided because of the expansion of the turbine. Using only a single generator in the production of these three outputs together, the costs of additional boilers and the need for a heat source are also saved. In order to demonstrate that the system proposed in this study offers a more optimum solution, the techno-economic parameters obtained based on energy, exergy, economic, and environmental analysis were compared with the parameters of similar scale systems in the literature. The design parameters of the proposed system were determined through a parametric optimization study to exceed the maximum efficiency and effectiveness and reduce the production cost rate values of the compared systems.

Keywords: solar energy, absorption technology, Rankine cycle, multigeneration energy system

Procedia PDF Downloads 58

Authors: Hicran Açıkel, Hüseyin Arak, D. Ali Açıkel

Abstract:

Train or high-speed train is a land transportation vehicle, which is safe and offers passengers flight-like comfort while it is preferred for busy lines with respect to passengers. In this study, TCDD’s (Turkish State Railroads Company) targets for the year of 2023, the planned high-speed train lines, improvements, which are considered for the existing lines, and achievability of these targets are examined.

Keywords: train, high-speed train, TCDD, transportation

Procedia PDF Downloads 247

Authors: Hüseyin Biçer

Abstract:

There are more than a thousand endemic plants growing in Turkey. On the other hand, apart from these plantsAnatolia is home to more plant diversitythan the neighboring countries due to its transitional zone. These plants become a part of traditional medicine in the hope of curing the people with whom they have lived for thousands of years. No matter how important the climate is for the plant, the diseases of the region have an important place in the plant's life. While the plants used for tea are in the foreground in regions with heavy winters, the use of raw plants and fruits is common in some gastrointestinal problems. The aim of this study is explaining using the area of endemic plants in Anatolia.

Keywords: anatolian traditional medicine, traditional medicine, anatolian medicine, herbs

Procedia PDF Downloads 179

Authors: Huseyin Duran, Yesim Benal Oztekin, Kazim Kubilay Vursavus, Ilker Huseyin Celen

Abstract:

There are two main approaches to manufacturing, market and usage of plant protection machinery in Turkey. The first approach is called as ‘Product Safety Approach’ and could be summarized as minimum health and safety requirements of consumer needs on plant protection equipment and machinery products. The second approach is the practices related to the Plant Protection Equipment and Machinery Directive. Product safety approach covers the plant protection machinery product groups within the framework of a new approach directive, Machinery Safety Directive (2006/42 / AT). The new directive is in practice in our country by 03.03.2009, parallel to the revision of the EU Regulation on the Directive (03.03.2009 dated and numbered 27158 published in the Official Gazette). ‘Pesticide Application for Machines’ paragraph is added to the 2006/42 / EC Machinery Safety Directive, which is, in particular, reveals the importance of primary health care and product safety issue, explaining the safety requirements for machines used in the application of plant protection products. The Ministry of Science, Industry and Technology is the authorized organizations in our country for the publication and implementation of this regulation. There is a special regulation, carried out by Ministry of Food, Agriculture and Livestock General Directorate of Food and Control, on the manufacture and sale of plant protection machinery. This regulation, prepared based on 5996 Veterinary Services, Plant Health, Food and Feed Law, is ‘Regulation on Plant Protection Equipment and Machinery’ (published on 02.04.2011 whit number 27893 in the Official Gazette). The purposes of this regulation are practicing healthy and reliable crop production, the preparation, implementation and dissemination of the integrated pest management programs and projects for the development of human health and environmentally friendly pest control methods. This second regulation covers: approval, manufacturing, licensing of Plant Protection Equipment and Machinery; duties and responsibilities of the dealers; principles and procedures related to supply and control of the market. There are no inspection procedures for the application of currently used plant protection machinery in Turkey. In this study, content and application principles of all regulation approaches currently used in Turkey are summarized.

Keywords: plant protection equipment and machinery, product safety, market surveillance, inspection procedures

Procedia PDF Downloads 258

Authors: Sibel Celik, Hüseyin Ergin

Abstract:

The paper aims to find the best volatility forecasting model for stock markets in Turkey. For this purpose, we compare performance of different volatility models-both traditional GARCH model and high frequency based volatility models- and conclude that both in pre-crisis and crisis period, the performance of high frequency based volatility models are better than traditional GARCH model. The findings of paper are important for policy makers, financial institutions and investors.

Keywords: volatility, GARCH model, realized volatility, high frequency data

Procedia PDF Downloads 486

Authors: Raif Parlakkaya, Huseyin Cetin, Halil Akmese, Mesut Murat Adabali

Abstract:

As the economies of other countries in the Mediterranean Basin, the tourism sector in our country has a high denominator in economics. Tourism businesses, which are building blocks of tourism, sector faces with a variety of problems during their activities. These problems faced make business efficiency and competition conditions of the businesses difficult. Most of the problems faced by the tourism businesses and the information of consumers about consumers’ rights were used in this study, which is conducted to determine the problems of tourism businesses in the Central Anatolia Region. It is aimed to contribute the awareness of staff and executives working at tourism sector and to attract attention of businesses active concurrently with tourism sector and legislators.

Keywords: financial problems, the problems of tourism businesses, tourism businesses, tourism sector in Turkey

Procedia PDF Downloads 488

Authors: Eyyüp Murat Karakurt, Yan Huang, Mehmet Kaya, Hüseyin Demirtaş, Alper İncesu

Abstract:

In this study, Ti-(x) Nb (at. %) master alloys (x:10, 20, and 30) were fabricated following a standard powder metallurgy route and were sintered at 1200 ˚C for 6h, under 300 MPa by powder metallurgy method. The effect of the Nb concentration in Ti matrix and porosity level was examined experimentally. For metallographic examination, the alloys were analysed by optical microscopy and energy dispersive spectrometry analysis. In addition, X-ray diffraction was performed on the alloys to determine which compound formed in the microstructure. The compression test was applied to the alloys to understand the mechanical behaviors of the alloys. According to Nb concentration in Ti matrix, the β phase increased. Also, porosity level played a crucial role on the mechanical performance of the alloys.

Keywords: Nb concentration, porosity level, powder metallurgy, The β phase

Procedia PDF Downloads 266

Authors: Tansa Nisan Gunerhan

Abstract:

Dementia comes in different forms, including Alzheimer's disease. The most common dementia diagnosis among elderly individuals is Alzheimer's disease. On average, for patients with Alzheimer’s, life expectancy is around 4-8 years after the diagnosis; however, expectancy can go as high as twenty years or more, depending on the shrinkage of the brain. Normally, along with aging, the brain shrinks at some level but doesn’t lose a vast amount of neurons. However, Alzheimer's patients' neurons are destroyed rapidly; hence problems with loss of memory, communication, and other metabolic activities begin. The toxic changes in the brain affect the stability of the neurons. Beta-amyloid and tau are two proteins that are believed to play a role in the development of Alzheimer's disease through their toxic changes. Beta-amyloid is a protein that is produced in the brain and is normally broken down and removed from the body. However, in people with Alzheimer's disease, the production of beta-amyloid increases, and it begins to accumulate in the brain. These plaques are thought to disrupt communication between nerve cells and may contribute to the death of brain cells. Tau is a protein that helps to stabilize microtubules, which are essential for the transportation of nutrients and other substances within brain cells. In people with Alzheimer's disease, tau becomes abnormal and begins to accumulate inside brain cells, forming neurofibrillary tangles. These tangles disrupt the normal functioning of brain cells and may contribute to their death, forming amyloid plaques which are deposits of a protein called amyloid-beta that build up between nerve cells in the brain. The accumulation of amyloid plaques and neurofibrillary tangles in the brain is thought to contribute to the shrinkage of brain tissue. As the brain shrinks, the size of the brain may decrease, leading to a reduction in brain volume. Brain atrophy in Alzheimer's disease is often accompanied by changes in the structure and function of brain cells and the connections between them, leading to a decline in brain function. These toxic changes that accumulate can cause symptoms such as memory loss, difficulty with thinking and problem-solving, and changes in behavior and personality.

Keywords: Alzheimer, amyloid-beta, brain atrophy, neuron, shrinkage

Procedia PDF Downloads 95

Authors: Hasan Fatih Ertuğrul, Beytullah Okur, Huseyin Üvet, Kadir Erkan

Abstract:

The objective of this paper is to analyze a 4-pole hybrid magnetic levitation system by using 3D finite element and analytical methods. The magnetostatic analysis of the system is carried out by using ANSYS MAXWELL-3D package. An analytical model is derived by magnetic equivalent circuit (MEC) method. The purpose of magnetostatic analysis is to determine the characteristics of attractive force and rotational torques by the change of air gap clearances, inclination angles and current excitations. The comparison between 3D finite element analysis and analytical results are presented at the rest of the paper.

Keywords: yoke hybrid electromagnet, 3D finite element analysis, magnetic levitation system, magnetostatic analysis

Procedia PDF Downloads 727

Authors: Hatice Guzel, Imran Oral, Huseyin Isler

Abstract:

In this study, elastic constants, Young’s modulus, Poisson’s ratios, and shear moduli of orthotropic composite materials, consisting of E-glass/epoxy and carbon/epoxy, were calculated by ultrasonic velocities which were measured using ultrasonic pulse-echo method. 35 MHz computer controlled analyzer, 60 MHz digital oscilloscope, 5 MHz longitudinal probe, and 2,25 MHz transverse probe were used for the measurements of ultrasound velocities, the measurements were performed at ambient temperature. It was understood from the data obtained in this study that, measured ultrasound velocities and the calculated elasticity coefficients were depending on the fiber orientations.

Keywords: composite materials, elastic constants, orthotropic materials, ultrasound

Procedia PDF Downloads 292

Authors: Tuğrul Aksoy, Hüseyin Karabıyık

Abstract:

Reloading vehicles are the vehicles which are generally equipped with a crane and used to carry a stowage from a point and locate onto the vehicle or vice versa. In this study, structural analysis of a reloading vehicle was performed under the loads which are predicted to be exposed under operating conditions via the finite element method. Among the finite element analysis results, the stress and displacement distributions of the vehicle and the contact pressure distributions of the guide rings within the stabilization legs were examined. Vehicle design was improved by strengthening certain parts according to the analysis results. The analyses performed for the final design were verified by the experiments involving strain gauge measurements.

Keywords: structural analysis, reloading vehicle, crane, strain gauge

Procedia PDF Downloads 70

Authors: Eyyup Murat Karakurt, Yan Huang, Mehmet Kaya, Huseyin Demirtas

Abstract:

In this study, the effect of the porosity effect of Ti-20Zr alloy produced by powder metallurgy as a biomaterial was investigated experimentally. The Ti based alloys (Ti-20%Zr (at.) were produced under 300 MPa, for 6 h at 1200 °C. Afterward, the microstructure of the Ti-based alloys was analyzed by optical analysis, scanning electron microscopy, energy dispersive spectrometry. Moreover, compression tests were applied to determine the mechanical behaviour of samples. As a result, highly porous Ti-20Zr alloys exhibited an elastic modulus close to human bone. The results later were compared theoretically and experimentally.

Keywords: porosity effect, Ti based alloys, elastic modulus, compression test

Procedia PDF Downloads 230

Authors: Huseyin Altundag, Emel Bina, Esra Altıntıg

Abstract:

The aim of this study is determining amount of Al, Cu, Fe, Mn, Ni, Pb and Zn in the samples of honey which are gathered from Sakarya and Istanbul regions. In this study the evaluation of the trace elements in honeys samples are gathered from Sakarya and Istanbul, Turkey. The sample preparation phase is performed via wet decomposition method and microwave digestion system. The accuracy of the method was corrected by the standard reference material, Tea Leaves (INCY-TL-1) and NIST SRM 1515 Apple leaves. The comparison between gathered data and literature values has made and possible resources of the contamination to the samples of honey have handled. The obtained results will be presented in ICCIS 2015: XIII International Conference on Chemical Industry and Science.

Keywords: Wet decomposition, Microwave digestion, Trace element, Honey, ICP-OES

Procedia PDF Downloads 462

Authors: Murad Aydin Şanda, Hasan Hüseyin Doğan, Öyküm Öztürk

Abstract:

Element contents were analysed in some wild Boletus taxa [Boletus fechtnerii, Boletus edulis, Boletus dupainii, Boletus calopus, Boletus pulverulentus, Boletus rhodoxanthus] from Marmara region of Turkey by ICP-AES equipment. The element uptake levels were observed at different amounts in each Boletus species. The highest Fe, Ca, Ni, Cd, and Cr concentrations were determined as 4927, 1927, 3.56, 2.69 and 2.63 mg.kg-1 in B. fechtnerii respectively. B. dupainii has highest K, Mg, Mn, and Zn concentrations as 41910, 2757, 476, and 125 mg.kg-1 respectively, whereas B. calopus has highest P, Cu, and B concentrations as 4982, 48.6, and 28.3 mg.kg-1 respectively. B. edulis has highest Na and S contents as 1666 and 5544 mg.kg-1 respectively. Although B. pulverulentus has only the highest Al content as 871 mg.kg-1, on the other hand B. rhodoxanthus has highest Mo concentrations as 0.86 mg.kg-1.

Keywords: Boletus, element, macrofungi, Turkey

Procedia PDF Downloads 485

Authors: Emine Feyza Şükür, Mevlüt Türköz, Murat Dilmeç, Hüseyin Selçuk Halkacı

Abstract:

In this study, a warm bulge test system was designed, built and experimentally validated to perform warm bulge tests with all necessary systems. In addition, performance of each sub-system is validated through repeated production and/or test runs as well as through part quality measurements. Validation and performance tests were performed to characterize the repeatability of the system. As a result of these tests, the desired temperature distribution on the sheet metal was obtained by the heating systems and the good repeatability of the bulge tests was obtained. Consequently, this study is expected to provide other researchers and manufacturer with a set of design and process guidelines to develop similar systems.

Keywords: design, test unit, warm bulge test unit, validation test

Procedia PDF Downloads 491

Authors: Huseyin Gokberk, Shian Gao

Abstract:

CFD analysis of the relationship between the coefficients of lift and drag with respect to the angle of attack on a NACA 2412 wing section of an RC plane is conducted. Both the 2D and 3D models are investigated with the turbulence model. The 2D analysis has a free stream velocity of 10m/s at different AoA of 0°, 2°, 5°, 10°, 12°, and 15°. The induced drag and drag coefficient increased throughout the changes in angles even after the critical angle had been exceeded, whereas the lift force and coefficient of lift increased but had a limit at the critical stall angle, which results in values to reduce sharply. Turbulence flow characteristics are analysed around the aerofoil with the additions caused due to a finite 3D model. 3D results highlight how wing tip vortexes develop and alter the flow around the wing with the effects of the tapered configuration.

Keywords: CFD, turbulence modelling, aerofoil, angle of attack

Procedia PDF Downloads 225

Authors: Murad Aydin Şanda, Hasan Hüseyi̇n Doğan

Abstract:

Twenty-two element contents were analyzed in five wild Agaricus and Agrocybe taxa [Agaricus bresadolanus Bohus, Agaricus essettei Bon, Agaricus xanthoderma Genev. Agrocybe paludosa (J.E. Lange) Kühner & Romagn. Ex Bon and Agrocybe praecox (Pers.) Fayod] from Marmara region of Turkey by ICP-AES equipment. The element uptake levels were observed at different amounts in each Agaricus and Agrocybe species. The highest Pb and P concentrations were determined as 16.74 and 1.501 mg.kg-1 in A. essettei and A.bresadolanus respectively. Ag, P, and Hg concentrations were determined as 30685, 1,501, and 5978 mg.kg-1 in A. bresadolanus respectively. A. essettei has highest Ni, Cu, and Mn concentrations as 37.1, 43.63 and 1476 mg.kg-1 respectively, whereas A. praecox has highest Mo, Ni and P as 0.54, 10.20 and 27.9 mg.kg-1 respectively. A. paludosa has highest Zn, Cd, and Ba concentration as 336.8, 2.26 and 571.5 mg.kg-1 respectively. The highest K concentration was found in A. xanthoderma with 5.31 mg.kg-1. According to Who and FAO critters, identified metals in Agaricus and Agrocybe genera are not harmful to People if they would be consumed.

Keywords: agaricus, element, macrofungi, Turkey

Procedia PDF Downloads 259

Authors: Huseyin Cetin, Halil Akmese, Sercan Aras, Vahit Aytekin

Abstract:

Economic crisis, terrorism, global crisis and the relations between countries are the factors affecting tourism industry and tourism industry is vulnerable against these factors. In our study, there are two dimensions about Russian crisis. The crisis between Russia and Ukraine and decreased oil prices in global market have been entailed Russian economic crisis. This crisis has induced that the ruble, Russian currency, has depreciated against American dollars and consequently the purchasing power of Russian has weakened. This is the first dimension of our study. Second dimension is a political crisis between Turkey and Russia owing to the fact that the Russian Warcraft was brought down by Turkish army. The aim of this study is to explain the impact of the consequences of Russian crisis on Turkish tourism industry. The study has been limited only Antalya province.

Keywords: economic crisis, Turkey-Russian crisis, Turkey's tourism industry, tourism in Turkey

Procedia PDF Downloads 380

Authors: Düzgün Akmaz, Hüseyin Erişti

Abstract:

In the last few years, harmonics have been occurred with the increasing use of nonlinear loads, and these harmonics have been an ever increasing problem for the line systems. This situation importantly affects the quality of power and gives large losses to the network. An efficient way to solve these problems is providing harmonic compensation through parallel active power filters. Many methods can be used in the control systems of the parallel active power filters which provide the compensation. These methods efficiently affect the performance of the active power filters. For this reason, the chosen control method is significant. In this study, Fourier analysis (FA) control method and synchronous reference frame (SRF) control method are discussed. These control methods are designed for both eliminate harmonics and perform reactive power compensation in MATLAB/Simulink pack program and are tested. The results have been compared for each two methods.

Keywords: parallel active power filters, harmonic compensation, power quality, harmonics

Procedia PDF Downloads 459

Authors: Huseyin Kavas

Abstract:

Oleic acid (OA) capped superparamagnetic iron oxide nanoparticles (SPION) were synthesized by a thermal decomposition method. The composition of nanoparticles was confirmed by X-ray powder diffraction, and the morphology of particles was investigated by Atomic Force Microscopy (AFM), Scanning Electron Microscopy (SEM), and Transmission electron microscopy (TEM). The crystalline and particle size distribution of SPIONS capped with OA were investigated with a mean size of 6.99 nm and 8.9 nm, respectively. It was found that SPIONS have superparamagnetic characteristics with a saturation magnetization value of 64 emu/g. The thin film form of self-assembled SPIONS was fabricated by coating techniques of spin coating and dip coating. SQUID-VSM magnetometer and FMR techniques were performed in order to evaluate the magnetic properties of thin films, especially the existence of magnetic anisotropy. The thin films with magnetic anisotropy were obtained by self-assembled monolayers of SPION.

Keywords: magnetic materials, nanostructures, self-assembly, FMR

Procedia PDF Downloads 107

Authors: Hakan Aydogan, Fatih Bozkurt, Huseyin Coskun

Abstract:

In this study, the signal of brain electrical activities of the sixteen students selected from the Department of Electrical and Energy at Usak University have been recorded during a lecturer performed happiness emotions for the first group and anger emotions for the second group in different time while the groups were in the classroom separately. The attention and meditation data extracted from the recorded signals have been analyzed and evaluated toward the teacher’s specific emotion states simultaneously. Attention levels of students who are under influence of happiness emotions of the lecturer have a positive trend and attention levels of students who are under influence of anger emotions of the lecturer have a negative trend. The meditation or mental relaxation levels of students who are under influence of happiness emotions of the lecturer are 34.3% higher comparing with the mental relaxation levels of students who are under influence of anger emotions of the lecturer.

Keywords: brainwave, attention, meditation, education

Procedia PDF Downloads 419

Authors: Esma Kocaoglu, Oktay Talaz, Huseyin Cavdar, Murat Senturk, Deniz Eki̇nci̇

Abstract:

Glutathione reductase (GR) is a crucial antioxidant enzyme which is responsible for the maintenance of the antioxidant GSH (glutathione) molecule. Antimalarial effects of some chemical molecules are attributed to their inhibition of GR; thus inhibitors of this enzyme are expected to be promising candidates for the treatment of malaria. In this work, GR inhibitory properties of N-Methylpyrrole derivatives are reported. Firstly, GR was purified by means of affinity chromatography using 2’,5’-ADP-Sepharose 4B as ligand. Enzymatic activity was measured by Beutler’s method. Synthesis of the compounds was approved by thin layer chromatography and column chromatography. Different inhibitor concentrations were used and all compounds were tested in triplicate at each concentration used. It was found that all compounds have better inhibitory activity than the strong GR inhibitor N,N-bis(2-chloroethyl)-N-nitrosourea, especially three molecules, 8m, 8n, and 8q, are the best among them with low micromolar I₅₀ values. Findings of our study indicate that these Schiff base derivatives are strong GR inhibitors which can be used as leads for designation of novel antimalaria candidates.

Keywords: glutathione reductase, antimalaria, inhibitor, enzyme

Procedia PDF Downloads 270

Authors: Kazim G. Atman, Hüseyin Sirin

Abstract:

In theoretical physics, nonlocal phenomena has always been subject of debate. However, in the conventional mathematical approach where the developments of the physical systems are investigated by using the standard mathematical tools, nonlocal effects are not taken into account. In order to investigate the nonlocality in quantum mechanics and fractal property of space, fractional derivative operators are employed in this study. In this manner, fractional creation and annihilation operators are introduced and Einstein coefficients are taken into account as an application of concomitant formalism in quantum field theory. Therefore, each energy mode of photons are considered as fractional quantized harmonic oscillator hereby Einstein coefficients are obtained. Nevertheless, wave function and energy eigenvalues of fractional quantum mechanical harmonic oscillator are obtained via the fractional derivative order α which is a measure of the influence of nonlocal effects. In the case α = 1, where space becomes homogeneous and continuous, standard physical conclusions are recovered.

Keywords: Einstein’s Coefficients, Fractional Calculus, Fractional Quantum Mechanics, Nonlocal Theories

Procedia PDF Downloads 170

Authors: K. Youssef, Ç. Hüseyin

Abstract:

The blades of a wind turbine have the most important job of any wind turbine component; they must capture the wind and convert it into usable mechanical energy. The objective of this work is to determine the mechanical power of single big C-section of vertical wind turbine for wind car in a two-dimensional model. The wind car has a vertical axis with 3 single big C-section blades mounted at an angle of 120°. Moreover, the three single big C-section blades are directly connected to wheels by using various kinds of links. Gears are used to convert the wind energy to mechanical energy to overcome the load exercised on the main shaft under low speed. This work allowed a comparison of drag characteristics and the mechanical power between the single big C-section blades with the previous work on 3 C-section and 3 double C-section blades for wind car. As a result obtained from the flow chart the torque and power curves of each case study are illustrated and compared with each other. In particular, drag force and torque acting on each types of blade was taken at an airflow speed of 4 m/s, and an angular velocity of 13.056 rad/s.

Keywords: blade, vertical wind turbine, drag characteristics, mechanical power

Procedia PDF Downloads 520

Authors: Raif Parlakkaya, Umran Kahraman, Huseyin Cetin

Abstract:

Internet financial reporting and corporate governance issues are in the focus of academic and professional studies due to their attributed importance by stakeholders of corporations. Major aim of this study is to reveal the relationship between internet financial reporting which is held as dependent variable and some indicators of corporate governance such as the ratio of managerial ownership, blockholder ownership, number of independent members in the board of directors, frequency of meetings by audit committee and education level of audit committee members which are held as independent variables. Main purpose is to reveal the effect of corporate governance on the voluntary efforts of Internet Financial reporting. The scope of the research is limited to the Turkish Corporations listed in Borsa Istanbul (Istanbul Stock Exchange) and findings which are generated by means of SPSS software are revealed in results section and interpreted in conclusions.

Keywords: audit committee, corporate governance, internet financial reporting, managerial ownership

Procedia PDF Downloads 521

Authors: Huseyin Canci

Abstract:

Chlorophylls are green photosynthetic pigment in plants. Therefore, photosynthesis in plants occurs in the leaves. Roles of chlorophylls help plants to get energy from light. The aim of the present study is to compare of chlorophyll contents in some bean species including common bean (Phaseolus vulgaris L.) and runner bean (P. coccineous L.) and genotypes. This research was carried out in fields of Faculty of Agriculture, Akdeniz University in Antalya. Species and genotypes were grown in 2 m single row and 50 cm row spacing. A randomized blocks design was used with two replications. Totally, 124 beans species and genotypes which 122 common beans and 2 runner beans were sown on February, 17th 2014 by hand. Chlorophyll a + b (SPAD values) were determined seedling stage, days to flowering 50% and pod setting stage on bean genotypes. Results showed that there were significant differences for genotypes, stages and interaction of genotypes X stages. There was statistically significant relationships between yield and chlorophyll content of bean species and genotypes.

Keywords: bean, chlorophyll, Phaseolus, SPAD values

Procedia PDF Downloads 243

Authors: Huseyin Demir

Abstract:

This article is the results of a quantitative research about the effects of using interactive whiteboards in high school mathematics classroom. The aim of this article is to investigate the effects of using interactive whiteboards in high school mathematics classrooms. During the article the following questions are answered: 'What can we do with an interactive whiteboard?' and 'Do we really need those properties of the interactive whiteboard?' For the research part of the article, two groups of lessons are executed in Private Demirel College. In the first 6 weeks, the topics are taught on a normal blackboard. Starting from seventh week, we have used interactive whiteboard in the mathematics lessons. At the end of an eight week lectures with interactive whiteboards, a questionnaire is prepared and executed for the students. In the questionnaire 10 questions were asked about the benefits and differences of using the interactive whiteboards in mathematics lessons. By looking at the conclusion of the results of questionnaire and some discussions with the students we found some useful benefits of the usage of interactive whiteboards in mathematics lessons. This article will be helpful for the high school mathematics teachers.

Keywords: mathematics education, interactive whiteboard, blackboard, using interactive whiteboard in mathematics lessons

Procedia PDF Downloads 219

Authors: Hüseyin Biçer

Abstract:

The purpose of this study is an explanation of using and expectation traditional and complementary medicine in Turkey in terms of regionally, cultural and social. Due to geopolitics position, at the intersection of the Middle East, Africa and Europe, Turkey has historically hosted many civilizations and cultures, and hosts many religions at the same time and therefore is very open to intercultural interaction. For this reason, the traditional medicine of Turkey contains traces of many civilizations rather than a traditional medicine of its own. In Turkey, complementary and traditional medicine are used actively. The aim of the study is to measure whether the patients have ever taken traditional medicine as a caretaker or for the supportive treatment of their diseases, and as a result, their expectations. This cross-sectional, paper-based survey study was conducted in 27 state hospitals and 29 family medicine clinics in seven geographical regions of Turkey. Patients who had an appointment in the waiting rooms that day were included. 77.4% of the patients participating in the study stated that they used traditional medicine at least 5 times in their life, 27.6% stated that traditional medicine was sufficient in some diseases, and 36.8% stated that traditional treatment was a part of normal treatment. Both faith and cultural approaches in Turkey always keep traditional medicine close to drugs. Another danger, apart from traditional medicine drugs that can interact with drugs, is that patients find it sufficient to use traditional and complementary medicine alone.

Keywords: complementary medicine, traditional medicine, medicine in Turkey, alternative medicine

Procedia PDF Downloads 257

Authors: Huseyi̇n Das, Bülent Tarim, Sunay Demi̇r, Nurçi̇n Küçükkent, Sevi̇l Cengi̇z, Engi̇n Tülek, Veci̇hi̇ Aksakal

Abstract:

Atak-S laying hens are a high-performance strain obtained by crossing of the Rhode Island Red (RIR) X the Barred Plymouth Rock (BR) and are being produced in the Ankara Poultry Research Institute since 1997. Phenotypic and genetic improving studies are continued for this strain. In this study, 2 from IGF and 1 from IGFBP2, totally 3 different SNP polymorphisms were examined in 200 Atak-S chickens. Genotypes of SNPs were compared using ANOVA to body weight and egg number thorough 32 weeks of age, body weight at sexual maturity, age at sexual maturity and also egg quality traits such as egg shell breaking strength, shell thickness, Haugh unit, albumen index, yolk index, shape index. Only IGF(a) locus was in agreement with Hardy-Weinberg equilibrium, while, the other loci were not. As a result of the performance comparisons to the 3 SNP loci, it was determined that there has a significant association (P<0.05) between only TC genotypes of the IGF(b) locus and body weight at 32 weeks of age, but there was not any association to the other traits.

Keywords: Atak-S, Igf, Igfbp2, single nucleotide polymorphism

Procedia PDF Downloads 367

Authors: Hasan Hüseyin Doğan, Murad Aydın Şanda

Abstract:

Element contents were analyzed in twelve wild Amanita taxa [A. caesarea (Scop.) Pers., A. citrina (Schaeff.) Pers., A. excelsa (Fr.) Bertill., A. franchetii (Boud.) Fayod, A. gemmata (Fr.) Bertill., A. mairei Foley, A. muscaria (L.) Lam., A. pantherina (DC.) Krombh., A. phalloides (Fr.) Link, A. rubescens Pers., A. vaginata (Bull.) Lam., and A. verna (Bull.) Lam.] from Marmara Region of Turkey by ICP-AES equipment. The element uptake levels were observed at different amounts in each Amanita species. The highest Pb and P concentrations were determined as 15.11 and 0.861 mg.kg-1 in A. caesarea. Fe, Co, As, Sr, Ca, Mg, Al and Na concentrations were determined as 0.832, 4.56, 15.6, 18.9, 0.44, 0.253 and 0.190 mg.kg-1 in A. gemmata respectively. A. muscaria has highest Mo, Th, Sb, V, Cr, and B concentrations as 1.45, 1.17, 1.06, 44, 75, and 7 mg.kg-1 respectively, whereas A. rubescens has highest Zn, Ba, K, S, and Se as 430.6, 65.7, 5.47, 1.16, 11.5 mg.kg-1 respectively. A. muscaria has highest Hg concentrations as 5855 µg.kg-1.The highest Mn concentration were found in A. pantherina with 1176 mg.kg-1, the highest Cd were found in A. phalloides as 10.77 mg.kg-1. In contrast to A. verna has highest Ag and Au content as 77728 and 192 µg.kg-1. Although A. citrina has only the highest Ni content as 75.9 mg.kg-1and A. vaginata has Cu content as 67.04 mg.kg-1 on the other hand A. phalloides has highest Cd concentrations as 10.77 mg.kg-1.

Keywords: amanita, element, macrofungi, Turkey

Procedia PDF Downloads 413