Search results for: world bank

Authors: Abdulqader Alkhouzaam, Hazim Qiblawey, Majeda Khraisheh

Abstract:

Membrane treatment for desalination and wastewater treatment is one of the promising solutions to affordable clean water. It is a developing technology throughout the world and considered as the most effective and economical method available. However, the limitations of membranes’ mechanical and chemical properties restrict their industrial applications. Hence, developing novel membranes was the focus of most studies in the water treatment and desalination sector to find new materials that can improve the separation efficiency while reducing membrane fouling, which is the most important challenge in this field. Graphene oxide (GO) is one of the materials that have been recently investigated in the membrane water treatment sector. In this work, ultrafiltration polysulfone (PSF) membranes with high antifouling properties were synthesized by incorporating different loadings of GO. High-oxidation degree GO had been synthesized using a modified Hummers' method. The synthesized GO was characterized using different analytical techniques including elemental analysis, Fourier transform infrared spectroscopy - universal attenuated total reflectance sensor (FTIR-UATR), Raman spectroscopy, and CHNSO elemental analysis. CHNSO analysis showed a high oxidation degree of GO represented by its oxygen content (50 wt.%). Then, ultrafiltration PSF membranes incorporating GO were fabricated using the phase inversion technique. The prepared membranes were characterized using scanning electron microscopy (SEM) and atomic force microscopy (AFM) and showed a clear effect of GO on PSF physical structure and morphology. The water contact angle of the membranes was measured and showed better hydrophilicity of GO membranes compared to pure PSF caused by the hydrophilic nature of GO. Separation properties of the prepared membranes were investigated using a cross-flow membrane system. Antifouling properties were studied using bovine serum albumin (BSA) and humic acid (HA) as model foulants. It has been found that GO-based membranes exhibit higher antifouling properties compared to pure PSF. When using BSA, the flux recovery ratio (FRR %) increased from 65.4 ± 0.9 % for pure PSF to 84.0 ± 1.0 % with a loading of 0.05 wt.% GO in PSF. When using HA as model foulant, FRR increased from 87.8 ± 0.6 % to 93.1 ± 1.1 % with 0.02 wt.% of GO in PSF. The pure water permeability (PWP) decreased with loadings of GO from 181.7 L.m⁻².h⁻¹.bar⁻¹ of pure PSF to 181.1, and 157.6 L.m⁻².h⁻¹.bar⁻¹ with 0.02 and 0.05 wt.% GO respectively. It can be concluded from the obtained results that incorporating low loading of GO could enhance the antifouling properties of PSF hence improving its lifetime and reuse.

Keywords: antifouling properties, GO based membranes, hydrophilicity, polysulfone, ultrafiltration

Procedia PDF Downloads 132

Authors: Kazi Rizvan, Yamin Rekhu

Abstract:

Due to high competitiveness in industries throughout the world, every industry is trying hard to utilize all their resources to keep their productivity as high as possible. Many tools have been being used to ensure smoother flow of an operation, to balance tasks, to maintain proper schedules for tasks, to maintain proper sequence for tasks, to reduce unproductive time. All of these tools are used to augment productivity within an industry. Kanban board is one of them and of the many important tools of lean production system. Kanban Board is a visual depiction of the status of tasks. Kanban board shows the actual status of the tasks. It conveys the progress and issues of tasks as well. Using Kanban Board, tasks can be distributed among workers and operation targets can be visually represented to them. In this paper, an example of Kanban board from the aspects of Brothers Furniture Limited was taken and how the Kanban board system was implemented, how the board was designed and how it was made easily perceivable for the less literate or illiterate workers. The Kanban board was designed for the packing section of Brothers Furniture Limited. It was implemented for the purpose of representing the tasks flow to the workers and to mitigate the time that was wasted while the workers remained wondering about what task they should start after they finish one. Kanban board subsumed seven columns and there was a column for comments where if any problem occurred during working on the tasks. Kanban board was helpful for the workers as the board showed the urgency of the tasks. It was also helpful for the store section as they could understand which products and how much of them could be delivered to store at any certain time. Kanban board had all the information centralized which is why the work-flow got paced up and idle time was minimized. Regardless of many workers being illiterate or less literate, Kanban board was still explicable for the workers as the Kanban cards were colored. Since the significance of colors can be conveniently interpretable to them, colored cards helped a great deal in that matter. Hence, the illiterate or less literate workers didn’t have to spend time wondering about the significance of the cards. Even when the workers weren’t told the significance of the colored cards, they could grow a feeling about their meaning as colors can trigger anyone’s mind to perceive the situation. As a result, the board elucidated the workers about what board required them to do, when to do and what to do next. Kanban board alleviated excessive time between tasks by setting day-plan for targeted tasks and it also reduced time during tasks as the workers were acknowledged of forthcoming tasks for a day. Being very specific to the tasks, Kanban board helped the workers become more focused on their tasks helped them do their job with more perfection. As a result, The Kanban board helped achieve a 8.75% increase in productivity than the productivity before the Kanban board was implemented.

Keywords: color, Kanban Board, Lean Tool, literacy, packing, productivity

Procedia PDF Downloads 220

Authors: Amandeep Kaur, Ns Atri, Munruchi Kaur

Abstract:

Mushrooms have shaped our environment in ways that we are only beginning to understand. The weather patterns, topography, flora and fauna of Punjab state in India create favorable growing conditions for thousands of species of mushrooms, but the complete region was unexplored when it comes to coprophilous mushrooms growing on herbivorous dung. Coprophilous mushrooms are the most specialized fungi ecologically, which germinate and grow directly on different types of animal dung or on manured soil. In the present work, the diversity of coprophilous mushrooms' of Family Psathyrellaceae of the order Agaricales is explored, their relationship to the human world is sketched out, and their supreme significance to life on this planet is revealed. During the investigation, different dung localities from 16 districts of Punjab state have been explored for the collection of material. The macroscopic features of the collected mushrooms were documented on the Field key. The hand cut sections of the various parts of carpophore, such as pileus, gills, stipe and the basidiospores details, were studied microscopically under different magnification. Various authentic publications were consulted for the identification of the investigated taxa. The classification, authentic names and synonyms of the investigated taxa are as per the latest version of Dictionary of Fungi and the MycoBank. The present work deals with the taxonomy of 81 collections belonging to 39 species spread over 05 coprophilous genera, namely Psathyrella, Panaeolus, Parasola, Coprinopsis, and Coprinellus of family Psathyrellaceae. In the text, the investigated taxa have been arranged as they appear in the key to the genera and species investigated. In this work, have been thoroughly examined for their macroscopic, microscopic, ecological, and chemical reaction details. The authors dig deeper to give indication of their ecology and the dung type where they can be obtained. Each taxon is accompanied by a detailed listing of its prominent features and an illustration with habitat photographs and line drawings of morphological and anatomical features. Taxa are organized as per their status in the keys, which allow easy recognition. All the taxa are compared with similar taxa. The study has shown that dung is an important substrate which serves as a favorable niche for the growth of a variety of mushrooms. This paper shows an insight what short-lived coprophilous mushrooms can teach us about sustaining life on earth!

Keywords: abundance, basidiomycota, biodiversity, seasonal availability, systematics

Procedia PDF Downloads 44

Authors: Zeynep Aykul Yavuz

Abstract:

Misconception about design is about making a product pretty. However, the holistic approaches such as design thinking or human-centered design could take the design from making things nice to things inspired by real people and work with real-world limitations. Design thinking helps companies to understand not only problem area but also opportunities. It can be used by any people from any background which provide a space for companies where employees from different departments work together to solve the same problem. While demanding skills changing year to year into the market, previous technical skills are commons anymore. The frontier companies in the sectors look for interactive methods to solve problems. Moreover, the recruiter aims to understand the candidate’s design thinking skills (. The study includes a case study where a 21st century creative services company “ATÖLYE” offers innovation transformation with design thinking to a banking company. Both companies are located in İstanbul in Turkey. The banking company contacted with the ATÖLYE in January 2018 because they heard design thinking in different markets and how it transformed the way of working. The transformation process had 3 phases which were basic training of teams while getting coaching from ATÖLYE’s employees, coaching training with graduates of basic training, facilitator training. Employees built new skills while solving the banking company’s strategic problems. ATÖLYE offered experiential learning which helped employees’ making sense of new skills and knowledge. One day workshops were organized to create awareness about the practice of design thinking. In addition to these, a community of practice was built to create an environment to make reflections and discuss good practice. Not only graduates from the training program but also other employees from the company participated in the community gatherings. ATÖLYE did not train some employees in the company. Rather than that, its aim was to build a contemporary organization for the company. This provided a sustainable system in terms of human resources and motivation. At the beginning of 2020, employees from the first cohort in the basic training who took coaching training and facilitator training have started to design training for different groups in the company. They have considered what could be better in their training experience and designed new ones according to that, so they have been using design thinking to design the design training. This is one of the outcomes which shows the impact of all process clearly.

Keywords: design thinking, learning community, professional development, training, organizational transformation

Procedia PDF Downloads 100

Authors: Vicente Espinola, Luis Torres, Christhian Gonzalez

Abstract:

Entrepreneurship is a topic of current interest in Mexico and the World, which has been fostered through public policies with great impact on its generation. The strategies used in Mexico have not been successful, being motivational strategies aimed at the masses with the intention that someone in the process generates a venture. The strategies used for its development have been "picking of winners" favoring those who have already overcome the initial stages of undertaking without effective support. This situation shows a disarticulation that appears even more in social entrepreneurship; due to this, it is relevant to research on those elements that could develop them and thus integrate a model of entrepreneurship and social innovation for Mexico. Social entrepreneurship should be generating social innovation, which is translated into business models in order to make the benefits reach the population. These models are proposed putting the social impact before the economic impact, without forgetting its sustainability in the medium and long term. In this work, we present a simple model of innovation and social entrepreneurship for Guanajuato, Mexico. This algorithm was based on how social innovation could be generated in a systemic way for Mexico through different institutions that promote innovation. In this case, the technological parks of the state of Guanajuato were studied because these are considered one of the areas of Mexico where its main objectives are to make technology transfer to companies but overlooking the social sector and entrepreneurs. An experimental design of n = 60 was carried out with potential entrepreneurs to identify their perception of the social approach that the enterprises should have, the skills they consider required to create a venture, as well as their interest in generating ventures that solve social problems. This experiment had a 2K design, the value of k = 3 and the computational simulation was performed in R statistical language. A simple model of interconnected variables is proposed, which allows us to identify where it is necessary to increase efforts for the generation of social enterprises. The 96.67% of potential entrepreneurs expressed interest in ventures that solve social problems. In the analysis of the variables interaction, it was identified that the isolated development of entrepreneurial skills would only replicate the generation of traditional ventures. The variable of social approach presented positive interactions, which may influence the generation of social entrepreneurship if this variable was strengthened and permeated in the processes of training and development of entrepreneurs. In the future, it will be necessary to analyze the institutional actors that are present in the social entrepreneurship ecosystem, in order to analyze the interaction necessary to strengt the innovation and social entrepreneurship ecosystem.

Keywords: social innovation, model, entrepreneurship, technological parks

Procedia PDF Downloads 257

Authors: Sontana Mimapan, Phattarawadee Wattanasuntorn, Phanom Saijit

Abstract:

Aflatoxin contamination in maize, one of several agriculture crops grown for livestock feeding, is still a problem throughout the world mainly under hot and humid weather conditions like Thailand. In this study Aspergillus flavus (A. Flavus), the key fungus for aflatoxin production especially aflatoxin B1 (AFB1), isolated from naturally infected maize were identified and characterized according to colony morphology and PCR using ITS, Beta-tubulin and calmodulin genes. The strains were analysed for the presence of four aflatoxigenic biosynthesis genes in relation to their capability to produce AFB1, Ver1, Omt1, Nor1, and aflR. Aflatoxin production was then confirmed using immunoaffinity column technique. A loop-mediated isothermal amplification (LAMP) was applied as an innovative technique for rapid detection of target nucleic acid. The reaction condition was optimized at 65C for 60 min. and calcein flurescent reagent was added before amplification. The LAMP results showed clear differences between positive and negative reactions in end point analysis under daylight and UV light by the naked eye. In daylight, the samples with AFB1 producing A. Flavus genes developed a yellow to green color, but those without the genes retained the orange color. When excited with UV light, the positive samples become visible by bright green fluorescence. LAMP reactions were positive after addition of purified target DNA until dilutions of 10⁻⁶. The reaction products were then confirmed and visualized with 1% agarose gel electrophoresis. In this regards, 50 maize samples were collected from dairy farms and tested for the presence of four aflatoxigenic biosynthesis genes using LAMP technique. The results were positive in 18 samples (36%) but negative in 32 samples (64%). All of the samples were rechecked by PCR and the results were the same as LAMP, indicating 100% specificity. Additionally, when compared with the immunoaffinity column-based aflatoxin analysis, there was a significant correlation between LAMP results and aflatoxin analysis (r= 0.83, P < 0.05) which suggested that positive maize samples were likely to be a high- risk feed. In conclusion, the LAMP developed in this study can provide a simple and rapid approach for detecting AFB1 producing A. Flavus genes from maize and appeared to be a promising tool for the prediction of potential aflatoxigenic risk in livestock feedings.

Keywords: Aflatoxin B1, Aspergillus flavus genes, maize, loop-mediated isothermal amplification

Procedia PDF Downloads 223

Authors: Yongde Dai

Abstract:

The recent Chinese military action blockbusters, notably known as, Wolf Warrior/Zhan Lang (2015), Operation Mekong/Mei gong he xing dong (2016), Warrior 2/Zhan Lang 2 (2017) and Operation Red Sea/Hong hai xing dong (2018), have achieved phenomenal box-office successes and in particular, Wolf Warrior 2 became China’s highest-grossing film of all time. However, their yearly presence tends to show a paradigmic shift from China’s primacy of wen manliness (soft) to wu masculinity (hard). With the increasing cinematic exposure of a more muscular image manifesting in both the Chinese heroic soldiers and China itself as a rising global power, the backlash of the Chinese public against the proliferation of the feminized masculinity influenced by the ‘pretty-boy’ pop-culture and China’s harder approach to the current Sino-US tensions have correspondingly emerged and continued to brew. Chinese masculinity imagined in these films is one of the key factors that enable a gendered interpretation of the correlation between the Chinese on-screen fantasy and off-screen reality, that is, China’s public and official discourse about the hegemonic masculinity and non-hegemonic masculinity as well as China’s international profile on cinematic appearance and in today’s Sino-US relation. By reading closely at the four megahits as visual-audio texts with Chinese masculinity studies by Kam Louie and Geng Song, this paper attempts to examine the Chinese construction of manliness with historical accounts and argue why and how the recurrent emphasis of hard/military masculinity (wu) on screen are viewed as China’s contemporary rewriting of the ‘sick-man’ history in the film form. Through this investigation, the paper finds that the rewriting of the ‘sick-man’ history in the cinematic world through heroic brawny soldiers comes to resonate a collective anxiety of China in countering the real-life increasing feminized masculinity on the public appearance, particularly on the male celebrities. In addition, the superpower fantasy about China illuminates a hypermasculine imaginary of China as a global rising power and this coincidently echoes China’s current tougher diplomatic strategy tackling the Sino-US trade war, South China sea dispute and Huawei-US lawsuits.

Keywords: Chinese masculinity, Chinese military action film, feminized masculinity, manhood and nationhood, sick man of Asia

Procedia PDF Downloads 129

Authors: Mohammed Seid, Aklilu Azazh, Fikre Enquselassie, Engida Yisma

Abstract:

Background: Road traffic injuries are the eighth leading cause of death globally, and the leading cause of death for young people. More than a million people die each year on the world’s roads, and the risk of dying as a result of a road traffic injury is highest in the Africa. Methods: A prospective hospital-based study was undertaken to assess injury characteristics and outcome of road traffic accident among victims at Adult Emergency Department of Tikur Anbesa specialized hospital, Addis Ababa, Ethiopia. A structured pre-tested questionnaire was used to gather the required data. The collected data were analyzed using SPSS version 16.0. Results: A total of 230 road traffic accident victims were studied. The majority of the study subjects were men 165 (71.7%) and the male/female ratio was 2.6:1. The victims’ ages ranged from 14 to 80 years with the mean and standard deviations of 32.15 and ± 14.38 years respectively. Daily laborers (95 (41.3%)) and students (28 (12.2%)) were the majority of road traffic accident victims. Long-distance travelling Minibus (16.5%) was responsible for the majority of road traffic crash followed by followed by Taxi (14.8%) and pedestrians (62.6%) accounted for the majority of road traffic accident. Head (50.4%) and musculoskeletal (extremities) (47.0%) were the most common body region injured. Fractures (78.0%) and open wounds (56.5%) were the most common type of injuries sustained. Treatment of fracture was the most common procedure performed in 57.7 % of the victims. The overall length of hospital stay (LOS) ranged from 1 day to 61 days with mean (± standard deviation) of 7.12 ± 10.5 days and the mortality rate was 7.4 %. A significant higher proportion of victims aged 14-55 years were had less likelihood of death compared to those victims aged more than 55 years of age [Adjusted OR = 0.1 (95% CI: 0.01, 0.82)]. Conclusions: This study showed diverse injury characteristics and high morbidity and mortality among the victims attending Adult Emergency Department of Tikur Anbesa specialized hospital, Addis Ababa, Ethiopia. The findings reflect that road traffic accident is a major public health problem. Urgent road traffic accident preventive measures and prompt treatment of the victims are warranted in order to reduce morbidity and mortality among the victims.

Keywords: road traffic accident, injury characteristics, outcome, Tikur Anbesa specialized hospital, Addis Ababa, Ethiopia

Procedia PDF Downloads 364

Authors: Vidya Yadav

Abstract:

India’s youth bulge is now sharpest at the critical 15-24 age group, even as its youngest, and oldest age groups begin to narrow. As the ‘single year, age data’ for the 2011 Census releases the data on the number of people at each year of age in the population. The data shows that India’s working age population (15-64 years) is now 63.4 percent of the total, as against just short of 60 percent in 2001. The numbers also show that the ‘dependency ratio’ the ratio of children (0-14) and the elderly (65 above) to those in the working age has shrunk further to 0.55. “Even as the western world is in ageing situation, these new numbers show that India’s population is still very young”. As the fertility falls faster in urban areas, rural India is younger than urban India; while 51.73 percent of rural Indians are under the age of 24 and 45.9 percent of urban Indians are under 24. The percentage of the population under the age of 24 has dropped, but many demographers say that it should not be interpreted as a sign of the youth bulge is shrinking. Rather it is because of “declining fertility, the number of infants and children reduces first, and this is what we see with the number of under age 24. Indeed the figure shows that the proportion of children in the 0-4 and 5-9 age groups has fallen in 2011 compared to 2001. For the first time, the percentage of children in the 10-14 age group has also fallen, as the effect of families reducing the number of children they have begins to be felt. The present paper key issue is to examine that “whether this growing youth bulge has the right skills for the workforce or not”. The study seeks to examine the youth population structure and employment distribution among them in India during 2001-2011 in different industrial category. It also tries to analyze the workforce participation rate as main and marginal workers both for male and female workers in rural and urban India by utilizing an abundant source of census data from 2001-2011. Result shows that an unconscionable number of adolescents are working when they should study. In rural areas, large numbers of youths are working as an agricultural labourer. Study shows that most of the youths working are in the 15-19 age groups. In fact, this is the age of entry into higher education, but due to economic compulsion forces them to take up jobs, killing their dreams of higher skills or education. Youths are primarily engaged in low paying irregular jobs which are clearly revealed by census data on marginal workers. That is those who get work for less than six months in a year. Large proportions of youths are involved in the cultivation and household industries works.

Keywords: main, marginal, youth, work

Procedia PDF Downloads 273

Authors: Javier Alfonso Bonilla-Chávez, Angélica Lozano

Abstract:

In North America, more than 2,000 people annually die in accidents related to railroad tracks. In 2020, collisions at grade crossings were the main cause of deaths related to railway accidents in Mexico. Railway networks have constant interaction with motor transport users, cyclists, and pedestrians, mainly in grade crossings, where is the greatest vulnerability and risk of accidents. Usually, accidents at grade crossings are directly related to risky behavior and non-compliance with regulations by motorists, cyclists, and pedestrians, especially in developing countries. Around the world, countries classify these crossings in different ways. In Mexico, according to their dangerousness (high, medium, or low), types A, B and C have been established, recommending for each one different type of auditive and visual signaling and gates, as well as horizontal and vertical signaling. This classification is based in a weighting, but regrettably, it is not explained how the weight values were obtained. A review of the variables and the current approach for the grade crossing classification is required, since it is inadequate for some crossings. In contrast, North America (USA and Canada) and European countries consider a broader classification so that attention to each crossing is addressed more precisely and equipment costs are adjusted. Lack of a proper classification, could lead to cost overruns in the equipment and a deficient operation. To exemplify the lack of a good classification, six crossings are studied, three located in the rural area of Mexico and three in Mexico City. These cases show the need of: improving the current regulations, improving the existing infrastructure, and implementing technological systems, including informative signals with nomenclature of the involved crossing and direct telephone line for reporting emergencies. This implementation is unaffordable for most municipal governments. Also, an inventory of the most dangerous grade crossings in urban and rural areas must be obtained. Then, an approach for improving the classification of grade crossings is suggested. This approach must be based on criteria design, characteristics of adjacent roads or intersections which can influence traffic flow through the crossing, accidents related to motorized and non-motorized vehicles, land use and land management, type of area, and services and economic activities in the zone where the grade crossings is located. An expanded classification of grade crossing in Mexico could reduce accidents and improve the efficiency of the railroad.

Keywords: accidents, grade crossing, railroad, traffic safety

Procedia PDF Downloads 96

Authors: Pillay J. D., D. De Wit, J. F. Ducray

Abstract:

Field hockey is a popular international sport which is played in more than 100 countries across the world. Due to the nature of hockey, players repeatedly perform a combination of forward flexion and rotational movements of the spine in order to strike the ball. These movements have been shown to increase the risk of pain and injury to the lumbar spine. The aim of this study was to determine the prevalence and incidence of low back pain (LBP) in male adolescent field hockey players and the characteristics of LBP in terms of location, chronicity, disability, and treatment sought, as well as its association with selected risk factors. A survey was conducted on 112 male adolescent field hockey players in the eThekwini Municipality of KwaZulu-Natal, South Africa. The questionnaire contained sections on the demographics of participants, general characteristics of participants, health and lifestyle characteristics, low back pain patterns, treatment of low back pain, and the level of disability associated with LBP. The data were statistically analysed using IBM SPSS version 25 with statistical significance set at p-value <0.05. Descriptive statistics such as mean and standard deviation were used to summarise responses to continuous variables as appropriate. Categorical variables were described using frequency tables. Associations between risk factors and low back pain were tested using Pearson’s chi-square test and t-tests as appropriate. A total of 68 questionnaires were completed for analysis (67% participation rate); the period prevalence of LBP was 63.2% (35.0%:beginning of the season, 32.4%:mid-season, 22.1%: end of season). Incidence was 38.2%. The most common location for LBP was the middle low back region (39.5%), and the most common duration of pain was a few hours (32.6%). Most participants (79.1%) did not classify their pain as a disability, and only 44.2% of participants received medical treatment for their LBP. An interesting finding was the association between hydration and LBP (p = 0.050), i.e., those individuals who did not hydrate frequently during matches and training were significantly more likely to experience LBP. The results of this study, although limited to a select group of adolescents, showed a higher prevalence of LBP than that of previous studies. More importantly, even though most participants did not experience LBP classified as a disability, LBP still had a large impact on participants, as nearly half of the participants consulted with a medical professional for treatment. Need for the application of further strategies in the prevention and management of LBP in field hockey, such as adequate warm-up and cool-down, stretching exercises, rest between sessions, etc., are recommended as simple strategies to reduce LBP prevalence.

Keywords: adolescents, field hockey players, incidence, low back pain, prevalence, risk factors

Procedia PDF Downloads 47

Authors: Jayathilake Wijethunga B. G. Mudiyanselage, Jeewantha Ranawaka, Nirosha Lansakara

Abstract:

Introduction: Women imprisonment is rising in the world. Imprisoned women have more psychological problems and more adverse childhood experiences than the general population. Female prisoners who had psychological problems had more adverse childhood experiences than the prisoners who did not have psychological problems. Most of the imprisoned women are mothers. Mothers are the principal carer for the children. The psychological status of imprisoned female is worth seeking along with its associates since this is a group of women who need others assistance to make their life adjusted. Any intervention that could uplift their psychological wellbeing would make their life better if they are to be released out of the prison. Since there are no studies done in Sri Lanka to study the imprisoned women psychological wellbeing and their childhood experiences, it is important to study on this to find the magnitude of the problem in Sri Lanka. Methodology: A descriptive cross-sectional study was done at the Welikada Prison, Colombo, among the imprisoned women. 273 imprisoned women were selected using simple random sampling technique. Using interviewer administered questionnaire 270 women were interviewed. Three women did not consent for the study. Frequencies of the selected socio demographic characteristics and selected childhood experiences calculated. GHQ 30 questionnaire was used to assess the psychological distress. Odds ratio was used to calculate the associations between the psychological distress and the selected socio demographic characteristics, selected childhood experiences. Results: Response rate was 98.9%. Mean age of the imprisoned women were 41.28years (SD ±11.86yrs) and Most of women were within the age group of 35-49 years (38.1%). Of them 68.5% were currently married and majority had at least one child. (86.3%). House hold member’s smoking (58.5%) and alcohol (40.4%) use was the commonest adverse childhood experience experienced by the imprisoned women. Nearly one fourth (22.6%) of the imprisoned women had attempted suicide during their life and more than half (55.7%) of them had attempted before the age of 18 years. Similarly of the 258 women who had been sexually active during their life, half (50.0%) of the women had exposed to sexual activities during first eighteen years of life and mean age at first sexual exposure was 19.2 (SD±4.86) years. Nearly three forth (73.7%) of imprisoned women were psychologically distressed in the study sample. Being a women of aged less than 25 years((OR=4.51, 95% CI=1.035-19.64)),previous history of suicidal attempts(OR=2.10,95%CI =1.00-4.41), not having enough foods to eat( OR=2.97, 1.009-8.75) and absence of someone to tell worries (OR=0.355, 95% CI =0.113-0.945) during childhood were significantly associate with psychological distress. Conclusion: Nearly three forth of the imprisoned women were psychologically distressed and younger age, history of suicidal attempts, the absence of someone to tell their worries and not having enough food to eat during childhood were risk factors for psychological distress. Recommendation: Need to strengthen the rehabilitation and mental health services to the imprisoned women.

Keywords: adverse childhood experiences, imprisoned women, psychological distress, prisoners

Procedia PDF Downloads 253

Authors: Alberto Mínguez-Martínez, Jesús De Vicente Y Oliva

Abstract:

It seems that we live in a world in which the trend in industrial environments is the miniaturization of systems and materials and the fabrication of parts at the micro-and nano-scale. The problem arises when manufacturers want to study the quality of their production. This characteristic is becoming crucial due to the evolution of the industry and the development of Industry 4.0. As Industry 4.0 is based on digital models of production and processes, having accurate measurements becomes capital. At this point, the metrology field plays an important role as it is a powerful tool to ensure more stable production to reduce scrap and the cost of non-conformities. The most extended measuring instruments that allow us to carry out accurate measurements at these scales are optical microscopes, whether they are traditional, confocal, focus variation microscopes, profile projectors, or any other similar measurement system. However, the accuracy of measurements is connected to the traceability of them to the SI unit of length (the meter). The fact of providing adequate traceability to 2D and 3D dimensional measurements at micro-and nano-scale in industrial environments is a problem that is being studied, and it does not have a unique answer. In addition, if commercial material standards for micro-and nano-scale are considered, we can find that there are two main problems. On the one hand, those material standards that could be considered complete and very interesting do not give traceability of dimensional measurements and, on the other hand, their calibration is very expensive. This situation implies that these kinds of standards will not succeed in industrial environments and, as a result, they will work in the absence of traceability. To solve this problem in industrial environments, it becomes necessary to have material standards that are easy to use, agile, adaptive to different forms, cheap to manufacture and, of course, traceable to the definition of meter with simple methods. By using these ‘customized standards’, it would be possible to adapt and design measuring procedures for each application and manufacturers will work with some traceability. It is important to note that, despite the fact that this traceability is clearly incomplete, this situation is preferable to working in the absence of it. Recently, it has been demonstrated the versatility and the utility of using laser technology and other AM technologies to manufacture customized material standards. In this paper, the authors propose to manufacture a customized material standard using an ultraviolet laser system and a method to calibrate it. To conclude, the results of the calibration carried out in an accredited dimensional metrology laboratory are presented.

Keywords: industrial environment, material standards, optical measuring instrument, traceability

Procedia PDF Downloads 104

Authors: Pradip Kumar Das

Abstract:

India is a developing country and is also one of the most industrialized developing countries of the world. In post-independence period, industry has grown rapidly in India and with industrialization corporate sector in the country has been growing day after day. Nowadays, the investment is not limited to be shareholders alone, apart from the shareholders the common people of the society have also started investing in shares of the corporate sectors. Thus, the responsibilities of the corporate sectors have increased much. Corporate financial reporting refers to a system which provides valuable information to different types of users in the society for taking resourceful decisions with regards to investment policy, organization credit worthiness, profitability, liquidity, provision of taxation etc. The quality of information available to different users fosters the efficient allocation of resources which are very urgent for economic development of a country like India. It is the responsibility of the management of the corporate sector to convey reliable and authentic information with the help of generally accepted accounting principles. Corporate sectors which disclose information through annual reports should be sufficient enough for the purpose of bringing out the salient features relating to business performances and other activities. However, the disclosures practices of the corporate sectors though annual reports have undergone several major changes from time to time. Many a time, these vital changes are in the fashion of presenting information in the annual reports and addition of so many non-statutory disclosures of the company. Very often managements of the corporate sectors are blamed for concealing true picture which is not desirable at all. The corporate financial reporting practice which in the current period has gained a place of prime importance suffers from certain limitations and invites question from the public about its reliability. Thus, the wide gap created by management between the exhibited picture and the real picture sometimes attains to such extent that the purpose of the reporting practice loses its importance. The requirement of full and adequate disclosure of information including information relating to human resources in the annual report in free trade economy of India helps the prospective investors to select the best portfolio of their investments. This paper is a reflection of a modest attempt of the author to highlight the corporate reporting practices followed in India. A cursory glance of the conceptual study shows limitations along with reliability of the reporting practices and suggests measures to overcome the shortcomings of the financial reporting practices.

Keywords: corporate enterprise, cursory glance, portfolio, yawning gap

Procedia PDF Downloads 395

Authors: G. Henini, Y. Laidani, F. Souahi, A. Labbaci, S. Hanini

Abstract:

Environmental contamination is a major problem being faced by the society today. Industrial, agricultural, and domestic wastes, due to the rapid development in the technology, are discharged in the several receivers. Generally, this discharge is directed to the nearest water sources such as rivers, lakes, and seas. While the rates of development and waste production are not likely to diminish, efforts to control and dispose of wastes are appropriately rising. Wastewaters from textile industries represent a serious problem all over the world. They contain different types of synthetic dyes which are known to be a major source of environmental pollution in terms of both the volume of dye discharged and the effluent composition. From an environmental point of view, the removal of synthetic dyes is of great concern. Among several chemical and physical methods, adsorption is a promising technique due to the ease of use and low cost compared to other applications in the process of discoloration, especially if the adsorbent is inexpensive and readily available. The focus of the present study was to assess the potentiality of Brahea edulis (BE) for the removal of synthetic dye Yellow bemacid (YB) from aqueous solutions. The results obtained here may transfer to other dyes with a similar chemical structure. Biosorption studies were carried out under various parameters such as mass adsorbent particle, pH, contact time, initial dye concentration, and temperature. The biosorption kinetic data of the material (BE) was tested by the pseudo first-order and the pseudo-second-order kinetic models. Thermodynamic parameters including the Gibbs free energy ΔG, enthalpy ΔH, and entropy ΔS have revealed that the adsorption of YB on the BE is feasible, spontaneous, and endothermic. The equilibrium data were analyzed by using Langmuir, Freundlich, Elovich, and Temkin isotherm models. The experimental results show that the percentage of biosorption increases with an increase in the biosorbent mass (0.25 g: 12 mg/g; 1.5 g: 47.44 mg/g). The maximum biosorption occurred at around pH value of 2 for the YB. The equilibrium uptake was increased with an increase in the initial dye concentration in solution (C_o = 120 mg/l; q = 35.97 mg/g). Biosorption kinetic data were properly fitted with the pseudo-second-order kinetic model. The best fit was obtained by the Langmuir model with high correlation coefficient (R² > 0.998) and a maximum monolayer adsorption capacity of 35.97 mg/g for YB.

Keywords: adsorption, Brahea edulis, isotherm, yellow Bemacid

Procedia PDF Downloads 161

Authors: D. Desai, J.Dixon, N. Jain, M. Datta

Abstract:

Microbial infections of scalp consist of symptomatic appearances associated with seborrhoeic dermatitis, folliculitis, furuncles, carbuncles and ringworm. The main causative organisms in these scalp-based infections are bacteria like S. aureus, P. aeruginosa and a fungus M. Furfur. Allopathic treatment of these infections is available and efficient, but occasionally, topical applications have been found to cause side effects. India is known as the botanical garden of the world and considered as the epicentre for utilization of traditional drugs. Many treatments based on herb extracts are commonly used in India. It has been observed treatment with ethnomedicines requires a higher dosage and greater time period. Additionally, repeated applications are required to obtain the full efficacy of the treatment. An attempt has been made to imbibe the traditional knowledge with nanotechnology to generate a proficient therapeutic against scalp infections. We have imbibed metallic nanoparticles with extracts from traditional medicines and propose to formulate an antimicrobial hair massager. Four commonly used herbs for treatment against scalp disorders like Zingiber officinale (ginger), Allium sativum (garlic), Azadirachta indica (neem) leaves and Citrus limon (lemon) peel was taken. 30 gms of dried homogenized powder was obtained and processed for obtaining the aqueous and ethanolic extract by soxhlet apparatus. The extract was dried and reconstituted to obtain working solution of 1mg/ml. Phytochemical analysis for the obtained extract was done. Synthesis of nanoparticles was mediated by incubating 1mM silver nitrate with extracts of various herbs to obtain silver nanoparticles. The formation of the silver nanoparticles (AgNPs) was monitored using UV-Vis spectroscopy. The AgNPs thus obtained were centrifuged and dried. The AgNPs thus formed were characterized by X Ray Diffraction, scanning electron microscopy and transmission electron microscopy. The size of the AgNPs varied from 10-20 nm and was spherical in shape. P. aeruginosa was plated on nutrient agar and comparative antibacterial activity was tested. Comparative antimicrobial potential was calculated for the extracts and the corresponding nanoconstructs. It was found AgNPs were more efficient than their aqueous and ethanolic counterparts except in the ase of C. limon. Statistical analysis was performed to validate the results obtained.

Keywords: ethnomedicine, nanoconstructs, scalp infections, Zingiber officinale

Procedia PDF Downloads 355

Authors: Ruchi Agarwal

Abstract:

In today’s world, companies are operating in dynamic, uncertain and ambiguous business environments. Globally, more companies are failing due to Environmental, Social and Governance (ESG) factors than ever. Corporate governance and risk management are intertwined in nature. For decades, corporate governance and risk management have been influenced by internal and external factors. Three schools of thought have influenced risk governance for decades: Agency theory, Contingency theory, and Institutional theory. Agency theory argues that agents have interests conflicting with principal interests and the information problem. Contingency theory suggests that risk management adoption is influenced by internal and external factors, while Institutional theory suggests that organizations legitimize risk management with regulators, competitors, and professional bodies. The conflicting objectives of theories have created problems for executives in organizations in the adoption of Risk Governance. So far, there are many studies that discussed risk culture and the role of actors in risk governance, but there are rare studies discussing the role of risk culture in the adoption of risk governance from a leadership style perspective. This study explores the adoption of risk governance in two contrasting industries, such as the Insurance and energy business, to understand whether risk governance is influenced by internal/external factors or whether risk culture is influenced by leaders. We draw empirical evidence by comparing the cases of an Indian insurance company and a renewable energy-based firm in India. We interviewed more than 20 senior executives of companies and collected annual reports, risk management policies, and more than 10 PPTs and other reports from 2017 to 2024. We visited the company for follow-up questions several times. The findings of my research revealed that both companies have used risk governance for strategic renewal of the company. Insurance companies use a transactional leadership style based on performance and reward for improving risk, while energy companies use rather symbolic management to make debt restructuring meaningful for stakeholders. Overall, both companies turned from loss-making to profitable ones in a few years. This comparative study highlights the role of different leadership styles in the adoption of risk governance. The study is also distinct as previous research rarely studied risk governance in two contrasting industries in reference to leadership styles.

Keywords: leadership style, corporate governance, risk management, risk culture, strategic renewal

Procedia PDF Downloads 30

Authors: Rui Fonseca-Pinto, Emanuel Silva, Rui Rijo, Ricardo Martinho, Bruno Carreira

Abstract:

The sedentary lifestyle is associated to the development of chronic noncommunicable diseases (obesity, hypertension, Diabetes Mellitus Type 2) and the World Health Organization, given the evidence that physical activity is determinant for individual and collective health, defined the Physical Activity Level (PAL) as a vital signal. Strategies for increasing the practice of physical activity in all age groups have emerged from the various social organizations (municipalities, universities, health organizations, companies, social groups) by increasingly developing innovative strategies to promote motivation strategies and conditions to the practice of physical activity. The adaptation of cities to the new paradigms of sustainable mobility has provided the adaptation of urban training circles and mobilized citizens to combat sedentarism. This adaptation has accompanied the technological evolution and makes possible the use of mobile technology to monitor outdoor training programs and also, through the network connection (IoT), use the training data to make personalized recommendations. This work presents a physical activity counseling platform to be used in the physical maintenance circuits of urban centers, the MOVIDA.polis. The platform consists of a back office for the management of circuits and training stations, and for a mobile application for monitoring the user performance during workouts. Using a QRcode, each training station is recognized by the App and based on the individual performance records (effort perception, heart rate variation) artificial intelligence algorithms are used to make a new personalized recommendation. The results presented in this work were obtained during the proof of concept phase, which was carried out in the PolisLeiria training circuit in the city of Leiria (Portugal). It was possible to verify the increase in adherence to the practice of physical activity, as well as to decrease the interval between training days. Moreover, the AI-based recommendation acts as a partner in the training and an additional challenging factor. The platform is ready to be used by other municipalities in order to reduce the levels of sedentarism and approach the weekly goal of 150 minutes of moderate physical activity. Acknowledgments: This work was supported by Fundação para a Ciência e Tecnologia FCT- Portugal and CENTRO2020 under the scope of MOVIDA project: 02/SAICT/2016 – 23878.

Keywords: physical activity, mHealth, urban training circuits, health promotion

Procedia PDF Downloads 157

Authors: Rosa Tsegaye Aga, Xuan Jiang, Pavel Vazquez Faci, Siqing Liu, Simon Rayner, Endalkachew Alemu, Markos Abebe

Abstract:

Tuberculosis (TB) is a major cause of disease globally. In most cases, TB is treatable and curable, but only with the proper treatment. There is a time when drug-resistant TB occurs when bacteria become resistant to the drugs that are used to treat TB. Current strategies to identify drug-resistant TB bacteria are laboratory-based, and it takes a longer time to identify the drug-resistant bacteria and treat the patient accordingly. But machine learning (ML) and data science approaches can offer new approaches to the problem. In this study, we propose to develop an ML-based model to predict the antibiotic resistance phenotypes of TB isolates in minutes and give the right treatment to the patient immediately. The study has been using the whole genome sequence (WGS) of TB isolates as training data that have been extracted from the NCBI repository and contain different countries’ samples to build the ML models. The reason that different countries’ samples have been included is to generalize the large group of TB isolates from different regions in the world. This supports the model to train different behaviors of the TB bacteria and makes the model robust. The model training has been considering three pieces of information that have been extracted from the WGS data to train the model. These are all variants that have been found within the candidate genes (F1), predetermined resistance-associated variants (F2), and only resistance-associated gene information for the particular drug. Two major datasets have been constructed using these three information. F1 and F2 information have been considered as two independent datasets, and the third information is used as a class to label the two datasets. Five machine learning algorithms have been considered to train the model. These are Support Vector Machine (SVM), Random forest (RF), Logistic regression (LR), Gradient Boosting, and Ada boost algorithms. The models have been trained on the datasets F1, F2, and F1F2 that is the F1 and the F2 dataset merged. Additionally, an ensemble approach has been used to train the model. The ensemble approach has been considered to run F1 and F2 datasets on gradient boosting algorithm and use the output as one dataset that is called F1F2 ensemble dataset and train a model using this dataset on the five algorithms. As the experiment shows, the ensemble approach model that has been trained on the Gradient Boosting algorithm outperformed the rest of the models. In conclusion, this study suggests the ensemble approach, that is, the RF + Gradient boosting model, to predict the antibiotic resistance phenotypes of TB isolates by outperforming the rest of the models.

Keywords: machine learning, MTB, WGS, drug resistant TB

Procedia PDF Downloads 32

Authors: Deepak Jugran, Rajesh Gill

Abstract:

Purpose: To study the demographic, sociological, gender and clinical profile of the children presented for childhood cataract at a public sector tertiary eye care centre in India. Methodology: The design of the study is retrospective, and hospital-based data is available with the Central Registration Department of the PGIMER, Chandigarh. The majority of the childhood cataract cases are being reported in this hospital, yet not each and every case of childhood cataract approaches PGI, Chandigarh. Nevertheless, this study is going to be pioneering research in India, covering five-year data of the childhood cataract patients who visited the Advanced Eye Centre, PGIMER, Chandigarh, from 1.1.2015 to 31.12.2019. The SPSS version 23 was used for all statistical calculations. Results: A Total of 354 children were presented for childhood cataract from 1.1.2015 to 31.12.2019. Out of 354 children, 248 (70%) were male, and 106 (30%) were female. In-spite of 2 flagship programmes, namely the National Programme for Control of Blindness (NPCB) and Aayushman Bharat (PM JAY) for eradication of cataract, no children received any financial assistance from these two programmes. A whopping 99% of these children belong to the poor families. In most of these families, the mothers were house-wives and did not employ anywhere. These interim results will soon be conveyed to the Govt. of India so that a suitable mechanism can be evolved to address this pertinent issue. Further, the disproportionate ratio of male and female children in this study is an area of concern as we don’t know whether the prevalence of childhood cataract is lower in female children or they are not being presented on time in the hospital by the families. Conclusion: The World Health Organization (WHO) has categorized Childhood blindness resulting from cataract as a priority area and urged all member countries to develop institutionalized mechanisms for its early detection, diagnosis and management. The childhood cataract is an emerging and major cause of preventable and avoidable childhood blindness, especially in low and middle-income countries. In the formative years, the children require a sound physical, mental and emotional state, and in the absence of either one of them, it can severely dent their future growth. The recent estimate suggests that India could suffer an economic loss of US$12 billion (Rs. 88,000 Crores) due to blindness, and almost 35% of cases of blindness are preventable and avoidable if detected at an early age. Besides reporting these results to the policy makers, synchronized efforts are needed for early detection and management of avoidable causes of childhood blindness such as childhood cataract.

Keywords: childhood blindness, cataract, Who, Npcb

Procedia PDF Downloads 92

Authors: Diego Caballero Vélez

Abstract:

In 1997 the Schengen Convention was incorporated in the mainstream of EU law by the Amsterdam Treaty. It came into effect in 1999 with the abolition of internal border controls in the EU, a milestone in the European integration project. In the meantime, due to the Yugoslav wars, nearly 700,000 asylum applications were filed in the European countries provoking a major refugee crisis. During this period, the opening of Eastern Europe fostered more cooperation and policy-making at the EU level in migration issues. Currently, a similar migratory crisis is taking place in Europe. The Syrian war has caused the most massive influx of immigrants in Europe since World War II. Nevertheless, the EU is adopting different migration policies from those implemented during the Yugoslav migration crisis. The current crisis has not led to a common European position but national responses have been offered on migration policies and responsibility for border security and asylum-seekers. A lot of factors can explain this change from a cooperation scenario to a no cooperation one, such as the economic crisis, but this research is focused on the premise that 'threat perception' lies at the core of some states grand strategies towards migration and it also influences in multilateral or unilateral responses. Migration rests at the nexus of three dimensions of security, including geopolitical interests, material production, and internal security. According to some scholars, migration policy is an 'integral instrument' of state grand strategy in that context. Political integration at the EU might be altered with the emergence of existential threats. In other words, some areas of the European cooperation can be transformed when a 'critical juncture' occurs, for instance a migration crisis. In that instance, Member states could see migration as a matter of threat that modifies their national interests and willingness to embrace international cooperation. This research will focus on EU Member states´ perceptions of the 90´s migration crisis and the current one. The goal is to evaluate to what extent the perceptions of threat are one of the main factors for explaining the transition from a cooperation scenario to a no-cooperation one in European asylum and security policies. To analyze threat perception in both migration crisis, some relevant Member states are treated as cases of study and a comparative analysis is carried out based on public opinion polls, public and policy discourse in migration, voting practices and deconstruction of the migration policies themselves both at EU level and a national one.

Keywords: cooperation, migration crisis, national responses, threat perception

Procedia PDF Downloads 227

Authors: Surinder Pal, Ajay Gupta, Johny Khajuria

Abstract:

Casting simulation helps visualize mold filling and casting solidification; predict related defects like cold shut, shrinkage porosity and hard spots; and optimize the casting design to achieve the desired quality with high yield. Flow and solidification of molten metals are, however, a very complex phenomenon that is difficult to simulate correctly by conventional computational techniques, especially when the part geometry is intricate and the required inputs (like thermo-physical properties and heat transfer coefficients) are not available. Simulation software is based on the process of modeling a real phenomenon with a set of mathematical formulas. It is, essentially, a program that allows the user to observe an operation through simulation without actually performing that operation. Simulation software is used widely to design equipment so that the final product will be as close to design specs as possible without expensive in process modification. Simulation software with real-time response is often used in gaming, but it also has important industrial applications. When the penalty for improper operation is costly, such as airplane pilots, nuclear power plant operators, or chemical plant operators, a mockup of the actual control panel is connected to a real-time simulation of the physical response, giving valuable training experience without fear of a disastrous outcome. The all casting simulation software has own requirements, like magma cast has only best for crack simulation. The latest generation software Auto CAST developed at IIT Bombay provides a host of functions to support method engineers, including part thickness visualization, core design, multi-cavity mold design with common gating and feeding, application of various feed aids (feeder sleeves, chills, padding, etc.), simulation of mold filling and casting solidification, automatic optimization of feeders and gating driven by the desired quality level, and what-if cost analysis. IIT Bombay has developed a set of applications for the foundry industry to improve casting yield and quality. Casting simulation is a fast and efficient solution for process for advanced tool which is the result of more than 20 years of collaboration with major industrial partners and academic institutions around the world. In this paper the process of casting simulation is studied.

Keywords: casting simulation software’s, simulation technique’s, casting simulation, processes

Procedia PDF Downloads 465

Authors: Steven Walker

Abstract:

This paper assesses recent data on the prevalence of poverty among children and young people diagnosed with mental health problems. The paper will demonstrate that the current hierarchy of risk factors for developing mental health problems needs adjusting to place poverty among the highest risk factors. Globally poverty is calculated to keep rising especially among less developed countries, and the post-Covid 19 economic recession in developed countries is set to rise. The experience of young people enduring Pandemic isolation is already being quantified and is expected to increase referrals for specialist intervention. Searches on several medical/psychological/social databases using keywords: poverty, children, mental illness were undertaken between 2018 and 2021. Worldwide, 700 million people still live in extreme poverty, half of whom are children. Children are physically and mentally disproportionately affected. Children who grow up impoverished lack the basic necessities they need to survive and thrive. 150 million children have been plunged into multidimensional poverty due to COVID-19. The poorest children are twice as likely to die in childhood than their wealthier peers. For those growing up in humanitarian crises such as Ukraine, the risks of deprivation and exclusion are magnified. In the world’s richest countries, one in seven children still live in poverty. Currently, one in four children in the European Union are at risk of falling into poverty. In Europe the impact of Brexit on the UK economy is predicted to reduce GDP by 5% in 2021 with a corresponding rise in poverty. According to the global charity Oxfam wealth inequality impacts levels of child abuse and affects women and girls worse and is a contributory factor in the risk of developing childhood mental illness. In the UK 2000 Foodbanks have opened since 2010, handing out 2 million food parcels annually, where there are currently 4 million children officially living in poverty. This research demonstrates that there is a strong association between families’ socio-economic circumstances and the chances that their children will experience mental illness. Evidence of this association is found repeatedly across developed countries. The paper will conclude by arguing that psychologists, psychiatrists, psychotherapists, social workers and CAMHS specialists need to place more importance on this critical socio-economic variable when assessing referred children and also advocate for political priorities in governments to reduce poverty and lower the risk of childhood mental illness.

Keywords: poverty, resilience, risk factor, socio economic, susceptibility

Procedia PDF Downloads 104

Authors: Kamrun Nahar Koly, Saimul Islam

Abstract:

Overweight and obesity is increasing at an alarming rate and a leading risk factor for morbidity throughout the world. In a country like Bangladesh where under nutrition and overweight both co-exist at the same time, but this issue has been underexplored as expected. The aim of the present study was to assess the knowledge, attitudes and identify the barriers of the physicians regarding overweight and obesity management on an urban hospital of Dhaka city in Bangladesh. A simple cross sectional study was conducted at two selected government and two private hospital to assess the knowledge, attitude and common barriers regarding overweight and obesity management among healthcare professionals. One hundred and fifty five physicians were surveyed. A standard questionnaire was constructed in local language and interview was administrated. Among the 155 physicians, majority 53 (34.20%) were working on SMC, 36 (23.20%) from DMC, 33 (21.30%) were based on SSMC and the rest 33 (21.30%) were from HFRCMH. Mean age of the study physicians were 31.88±5.92. Majority of the physicians 80 (51.60%) were not able to answer the correct prevalence of obesity but also a substantial number of them 75(48.40%) could mark the right answer. Among the physicians 150 (96.77%) reported BMI as a diagnostic index for overweight and obesity, where as 43 (27.74%) waist circumference, 30 (19.35%) waist hip ratio and 26 (16.77%) marked mid-arm circumference. A substantial proportion 71 (46.70%) of the physicians thought that they do not have much to do controlling weight problem in Bangladesh context though it has been opposed by 42 (27.60%) of the physicians and 39(25.70%) was neutral to comment. The majority of them 147 (96.1%) thought that a family based education program would be beneficial followed by 145 (94.8%) physicians mentioned about raising awareness among mothers as she is the primary caregiver. The idea of a school based education program will also help to early intervene referred by 142 (92.8%) of the physicians. Community based education program was also appreciated by 136 (89.5%) of the physicians. About 74 (47.7%) of them think that the patients still lack in motivation to maintain their weight properly at the same time too many patients to deal with can be a barrier as well assumed by 73 (47.1%) of them. Lack of national policy or management guideline can act as an obstacle told by 60 (38.7%) of the physicians. The relationship of practicing as a part of the general examination and chronic disease management was statistically significant (p<0.05) with physician occupational status. As besides, perceived barriers like lack of parents support, lack of a national policy was statistically significant (p<0.05) with physician occupational status. For the young physician, more training programme will be needed to transform their knowledge and attitude into practice. However, several important barriers interface for the physician treatment efforts and need to address.

Keywords: obesity management, physician, awareness, barriers, Bangladesh

Procedia PDF Downloads 154

Authors: Onur Ozveri, Korkut Karabag, Cagri Keles

Abstract:

It is an important issue that the occurring of production downtime and repair costs when machines fail in the machine intensive production industries. In the case of failure of more than one machine at the same time, which machines will have the priority to repair, how to determine the optimal repair time should be allotted for this machines and how to plan the resources needed to repair are the key issues. In recent years, Business Process Management (BPM) technique, bring effective solutions to different problems in business. The main feature of this technique is that it can improve the way the job done by examining in detail the works of interest. In the industries, maintenance and repair works are operating as a process and when a breakdown occurs, it is known that the repair work is carried out in a series of process. Maintenance main-process and repair sub-process are evaluated with process management technique, so it is thought that structure could bring a solution. For this reason, in an international manufacturing company, this issue discussed and has tried to develop a proposal for a solution. The purpose of this study is the implementation of maintenance and repair works which is integrated with process management technique and at the end of implementation, analyzing the maintenance related parameters like quality, cost, time, safety and spare part. The international firm that carried out the application operates in a free region in Turkey and its core business area is producing original equipment technologies, vehicle electrical construction, electronics, safety and thermal systems for the world's leading light and heavy vehicle manufacturers. In the firm primarily, a project team has been established. The team dealt with the current maintenance process again, and it has been revised again by the process management techniques. Repair process which is sub-process of maintenance process has been discussed again. In the improved processes, the ABC equipment classification technique was used to decide which machine or machines will be given priority in case of failure. This technique is a prioritization method of malfunctioned machine based on the effect of the production, product quality, maintenance costs and job security. Improved maintenance and repair processes have been implemented in the company for three months, and the obtained data were compared with the previous year data. In conclusion, breakdown maintenance was found to occur in a shorter time, with lower cost and lower spare parts inventory.

Keywords: ABC equipment classification, business process management (BPM), maintenance, repair performance

Procedia PDF Downloads 178

Authors: Fatima Khurshid, Noor Ul Ain, Syed Abdul Rehman Kashif, Zainab Riaz, Abdullah Usman Khan, Muhammad Imran

Abstract:

As the world is moving towards extra-high voltage (EHV) and ultra-high voltage (UHV) power systems, the performance requirements of power transformers are becoming crucial to the system reliability and security. With the transformers being an essential component of a power system, low health index of transformers poses greater risks for safe and reliable operation. Therefore, to meet the rising demands of the power system and transformer performance, researchers are being prompted to provide solutions for enhanced thermal and electrical properties of transformers. This paper proposes an approach to improve the health index of a transformer by using nano-technology in conjunction with bio-degradable oils. Vegetable oils can serve as potential dielectric fluid alternatives to the conventional mineral oils, owing to their numerous inherent benefits; namely, higher fire and flashpoints, and being environment-friendly in nature. Moreover, the addition of nanoparticles in the dielectric fluid further serves to improve the dielectric strength of the insulation medium. In this research, using the finite element method (FEM) in COMSOL Multiphysics environment, and a 2D space dimension, three different oil samples have been modelled, and the electric field distribution is computed for each sample at various electric potentials, i.e., 90 kV, 100 kV, 150 kV, and 200 kV. Furthermore, each sample has been modified with the addition of nanoparticles of different radii (50 nm and 100 nm) and at different interparticle distance (5 mm and 10 mm), considering an instant of time. The nanoparticles used are non-conductive and have been modelled as alumina (Al₂O₃). The geometry has been modelled according to IEC standard 60897, with a standard electrode gap distance of 25 mm. For an input supply voltage of 100 kV, the maximum electric field stresses obtained for the samples of synthetic vegetable oil, olive oil, and mineral oil are 5.08 ×10⁶ V/m, 5.11×10⁶ V/m and 5.62×10⁶ V/m, respectively. It is observed that for the unmodified samples, vegetable oils have a greater dielectric strength as compared to the conventionally used mineral oils because of their higher flash points and higher values of relative permittivity. Also, for the modified samples, the addition of nanoparticles inhibits the streamer propagation inside the dielectric medium and hence, serves to improve the dielectric properties of the medium.

Keywords: dielectric strength, finite element method, health index, nanotechnology, streamer propagation

Procedia PDF Downloads 129

Authors: Y. Landkocz, P. Gosset, A. Héliot, C. Corbière, C. Vendeville, V. Keravec, S. Billet, A. Verdin, C. Monteil, D. Préterre, J-P. Morin, F. Sichel, T. Douki, P. J. Martin

Abstract:

Air Pollution produced by automobile traffic is one of the main sources of pollutants in urban atmosphere and is largely due to exhausts of the diesel engine powered vehicles. The International Agency for Research on Cancer, which is part of the World Health Organization, classified in 2012 diesel engine exhaust as carcinogenic to humans (Group 1), based on sufficient evidence that exposure is associated with an increased risk for lung cancer. Amongst the strategies aimed at limiting exhausts in order to take into consideration the health impact of automobile pollution, filtration of the emissions and use of biofuels are developed, but their toxicological impact is largely unknown. Diesel exhausts are indeed complex mixtures of toxic substances difficult to study from a toxicological point of view, due to both the necessary characterization of the pollutants, sampling difficulties, potential synergy between the compounds and the wide variety of biological effects. Here, we studied the potential indirect genotoxicity of emission of Diesel engines through on-line exposure of rats in inhalation chambers to a subchronic high but realistic dose. Following exposure to standard gasoil +/- rapeseed methyl ester either upstream or downstream of a particle filter or control treatment, rats have been sacrificed and their lungs collected. The following indirect genotoxic parameters have been measured: (i) telomerase activity and telomeres length associated with rTERT and rTERC gene expression by RT-qPCR on frozen lungs, (ii) γH2AX quantification, representing double-strand DNA breaks, by immunohistochemistry on formalin fixed-paraffin embedded (FFPE) lung samples. These preliminary results will be then associated with global cellular response analyzed by pan-genomic microarrays, monitoring of oxidative stress and the quantification of primary DNA lesions in order to identify biological markers associated with a potential pro-carcinogenic response of diesel or biodiesel, with or without filters, in a relevant system of in vivo exposition.

Keywords: diesel exhaust exposed rats, γH2AX, indirect genotoxicity, lung carcinogenicity, telomerase activity, telomeres length

Procedia PDF Downloads 378

Authors: Elisabeth Unterfrauner, Christian Voigt

Abstract:

Since the foundation of the first Fab Lab by the Massachusetts Institute of Technology about 17 years ago, the Maker movement has spread globally with the foundation of maker spaces and Fab Labs worldwide. In these workshops, citizens have access to digital fabrication technologies such as 3D printers and laser cutters to develop and test their own ideas and prototypes, which makes it an attractive place for start-up companies. Know-How is shared not only in the physical space but also online in diverse communities. According to the Horizon report, the Maker movement, however, will also have an impact on educational settings in the following years. The European project ‘DOIT - Entrepreneurial skills for young social innovators in an open digital world’ has incorporated key elements of making to develop an early entrepreneurial education program for children between the age of six and 16. The Maker pedagogy builds on constructive learning approaches, learning by doing principles, learning in collaborative and interdisciplinary teams and learning through trial and error where mistakes are acknowledged as learning opportunities. The DOIT program consists of seven consecutive elements. It starts with a motivation phase where students get motivated by envisioning the scope of their possibilities. The second step is about Co-design: Students are asked to collect and select potential ideas for innovations. In the Co-creation phase students gather in teams and develop first prototypes of their ideas. In the iteration phase, the prototype is continuously improved and in the next step, in the reflection phase, feedback on the prototypes is exchanged between the teams. In the last two steps, scaling and reaching out, the robustness of the prototype is tested with a bigger group of users outside of the educational setting and finally students will share their projects with a wider public. The DOIT program involves 1,000 children in two pilot phases at 11 pilot sites in ten different European countries. The comprehensive evaluation design is based on a mixed method approach with a theoretical backbone on Lackeus’ model of entrepreneurship education, which distinguishes between entrepreneurial attitudes, entrepreneurial skills and entrepreneurial knowledge. A pre-post-test with quantitative measures as well as qualitative data from interviews with facilitators, students and workshop protocols will reveal the effectiveness of the program. The evaluation results will be presented at the conference.

Keywords: early entrepreneurial education, Fab Lab, maker education, Maker movement

Procedia PDF Downloads 113

Authors: Ahmed Slami, Med El Amine Brixi Nigassa, Nassima Labdelli, Sofiane Soulimane, Arnaud Pothier

Abstract:

Many people suffer from diabetes, a disease marked by abnormal levels of sugar in the blood; 285 million people have diabetes, 6.6% of the world adult population (in 2010), according to the International Diabetes Federation. Insulin medicament is invented to be injected into the body. Generally, the injection requires the patient to do it manually. However, in many cases he will be unable to inject the drug, saw that among the side effects of hyperglycemia is the weakness of the whole body. The researchers designed a medical device that injects insulin too autonomously by using micro-pumps. Many micro-pumps of concepts have been investigated during the last two decades for injecting molecules in blood or in the body. However, all these micro-pumps are intended for slow infusion of drug (injection of few microliters by minute). Now, the challenge is to develop micro-pumps for fast injections (1 microliter in 10 seconds) with accuracy of the order of microliter. Recently, studies have shown that only piezoelectric actuators can achieve this performance, knowing that few systems at the microscopic level were presented. These reasons lead us to design new smart microsystems injection drugs. Therefore, many technological advances are still to achieve the improvement of materials to their uses, while going through their characterization and modeling action mechanisms themselves. Moreover, it remains to study the integration of the piezoelectric micro-pump in the microfluidic platform features to explore and evaluate the performance of these new micro devices. In this work, we propose a new micro-pump model based on piezoelectric actuation with a new design. Here, we use a finite element model with Comsol software. Our device is composed of two pumping chambers, two diaphragms and two actuators (piezoelectric disks). The latter parts will apply a mechanical force on the membrane in a periodic manner. The membrane deformation allows the fluid pumping, the suction and discharge of the liquid. In this study, we present the modeling results as function as device geometry properties, films thickness, and materials properties. Here, we demonstrate that we can achieve fast injection. The results of these simulations will provide quantitative performance of our micro-pumps. Concern the spatial actuation, fluid rate and allows optimization of the fabrication process in terms of materials and integration steps.

Keywords: COMSOL software, piezoelectric, micro-pump, microfluidic

Procedia PDF Downloads 333

Authors: J. B. Athavale, Sean Clarke

Abstract:

Introduction According to ancient Indian scriptures, a person’s consciousness includes the physical body, the vital energy sheath (Pranshakti), the mental body (which includes one’s feelings and emotions), the intellectual body (which refers to one’s decision-making ability), and the Soul (which is the God Principle that resides in every person). Apart from the physical body, all the other aspects are subtle in nature. In today’s world, much attention is given to one’s physical appearance and intellectual prowess. While there have been improvements in the attention given to mental health, its complete nature is not understood, and in many cultures, mental ill health is considered taboo and looked down upon. Regarding the spiritual well-being of a person, our spiritual research has shown that people’s understanding and efforts are mostly lacking and superficial as they do not conform to Universal Spiritual Principles. Also, true well-being occurs only when all the bodies are healthy. Methodology The spiritual research team at the University has found that the spiritual aspect of a person’s life affects all the physical, psychological, and intellectual bodies of a person resulting in ill health. Cleansing these bodies at a spiritual level is essential to regain well-being. Using Aura and Energy Scanners and advanced sixth sense, we studied what causes spiritual impurity in various bodies and how to cleanse them. We measured the spiritual vibrations of a person and how they get affected due to various daily activities. For example, we studied the difference in a person’s aura before and after applying chemical-based makeup vs. natural makeup. Key Findings From the various spiritual research experiments we conducted, we found that: • All our actions and our thoughts affect our various bodies and have the potential to change the aura for the better or worse. • When there is an increase in negative vibrations around a person, negative energies from the subtle dimension are more likely to affect a person. • As the person’s spiritual level increases, the positivity in their aura also increases, and it is much easier to cleanse the various bodies spiritually. • Spiritual practice is like a general spiritual tonic that increases the positivity in one’s aura. The benefits of this are that it leads to mental stability and intellectual clarity. • Spiritual healing remedies augment any spiritual practice to obtain a faster healing effect. Conclusion Taking care of oneself spiritually has a positive halo effect on all one’s bodies. Spiritual cleansing is required regularly if one wants to attain a state of well-being. Spiritual practice and spiritual healing lead to spiritual growth, stability of mind, and less stress and reactions. Spiritually purer people affect the environment positively, and there is less unrest and more harmony between man and nature.

Keywords: body, spirituality, cleansing, consciousness

Procedia PDF Downloads 60