Search results for: manual data inquiry
11894 Zinc (II) Complexes of Nitrogen, Oxygen and Sulfur Coordination Modes: Synthesis, Spectral Studies and Antibacterial Activities
Authors: Ayodele Odularu, Peter Ajibade, Albert Bolhuis
Abstract:
This study aimed at assessing the antibacterial activities of four zinc (II) complexes. Zinc (II) complexes of nitrogen, oxygen and sulfur coordination modes were synthesized using direct substitution reaction. The characterization techniques involved physicochemical properties (molar conductivity) and spectroscopic techniques. The molar conductivity gave the non-electrolytic nature of zinc (II) complexes. The spectral studies of zinc (II) complexes were done using electronic spectra (UV-Vis) and Fourier Transform Infra-red Spectroscopy (FT-IR). Spectral data from the spectroscopic studies confirmed the coordination of the mixed ligands with zinc (II) ion. The antibacterial activities of zinc(II) complexes of were all in supportive of Overtone’s concept and Tweedy’s theory of chelation for bacterial strains of S. aureus MRSA252 and E coli MC4100 because the zones of inhibition were greater than the corresponding ligands. In summary, all zinc (II) complexes of ZEPY, ZE1PH, ZE1PY and ZE135PY all have potentials for antibacterial activities.Keywords: antibacterial activities, spectral studies, syntheses, zinc(II) complexes
Procedia PDF Downloads 26911893 A Simulation Model and Parametric Study of Triple-Effect Desalination Plant
Authors: Maha BenHamad, Ali Snoussi, Ammar Ben Brahim
Abstract:
A steady-state analysis of triple-effect thermal vapor compressor desalination unit was performed. A mathematical model based on mass, salinity and energy balances is developed. The purpose of this paper is to develop a connection between process simulator and process optimizer in order to study the influence of several operating variables on the performance and the produced water cost of the unit. A MATLAB program is used to solve the model equations, and Aspen HYSYS is used to model the plant. The model validity is examined against a commercial plant and showed a good agreement between industrial data and simulations results. Results show that the pressures of the last effect and the compressed vapor have an important influence on the produced cost, and the increase of the difference temperature in the condenser decreases the specific heat area about 22%.Keywords: steady-state, triple effect, thermal vapor compressor, Matlab, Aspen Hysys
Procedia PDF Downloads 16811892 Hybrid Robust Estimation via Median Filter and Wavelet Thresholding with Automatic Boundary Correction
Authors: Alsaidi M. Altaher, Mohd Tahir Ismail
Abstract:
Wavelet thresholding has been a power tool in curve estimation and data analysis. In the presence of outliers this non parametric estimator can not suppress the outliers involved. This study proposes a new two-stage combined method based on the use of the median filter as primary step before applying wavelet thresholding. After suppressing the outliers in a signal through the median filter, the classical wavelet thresholding is then applied for removing the remaining noise. We use automatic boundary corrections; using a low order polynomial model or local polynomial model as a more realistic rule to correct the bias at the boundary region; instead of using the classical assumptions such periodic or symmetric. A simulation experiment has been conducted to evaluate the numerical performance of the proposed method. Results show strong evidences that the proposed method is extremely effective in terms of correcting the boundary bias and eliminating outlier’s sensitivity.Keywords: boundary correction, median filter, simulation, wavelet thresholding
Procedia PDF Downloads 42311891 Variogram Fitting Based on the Wilcoxon Norm
Authors: Hazem Al-Mofleh, John Daniels, Joseph McKean
Abstract:
Within geostatistics research, effective estimation of the variogram points has been examined, particularly in developing robust alternatives. The parametric fit of these variogram points which eventually defines the kriging weights, however, has not received the same attention from a robust perspective. This paper proposes the use of the non-linear Wilcoxon norm over weighted non-linear least squares as a robust variogram fitting alternative. First, we introduce the concept of variogram estimation and fitting. Then, as an alternative to non-linear weighted least squares, we discuss the non-linear Wilcoxon estimator. Next, the robustness properties of the non-linear Wilcoxon are demonstrated using a contaminated spatial data set. Finally, under simulated conditions, increasing levels of contaminated spatial processes have their variograms points estimated and fit. In the fitting of these variogram points, both non-linear Weighted Least Squares and non-linear Wilcoxon fits are examined for efficiency. At all levels of contamination (including 0%), using a robust estimation and robust fitting procedure, the non-weighted Wilcoxon outperforms weighted Least Squares.Keywords: non-linear wilcoxon, robust estimation, variogram estimation, wilcoxon norm
Procedia PDF Downloads 44511890 A New Method to Estimate the Low Income Proportion: Monte Carlo Simulations
Authors: Encarnación Álvarez, Rosa M. García-Fernández, Juan F. Muñoz
Abstract:
Estimation of a proportion has many applications in economics and social studies. A common application is the estimation of the low income proportion, which gives the proportion of people classified as poor into a population. In this paper, we present this poverty indicator and propose to use the logistic regression estimator for the problem of estimating the low income proportion. Various sampling designs are presented. Assuming a real data set obtained from the European Survey on Income and Living Conditions, Monte Carlo simulation studies are carried out to analyze the empirical performance of the logistic regression estimator under the various sampling designs considered in this paper. Results derived from Monte Carlo simulation studies indicate that the logistic regression estimator can be more accurate than the customary estimator under the various sampling designs considered in this paper. The stratified sampling design can also provide more accurate results.Keywords: poverty line, risk of poverty, auxiliary variable, ratio method
Procedia PDF Downloads 45011889 Presence and Severity of Language Deficits in Comprehension, Production and Pragmatics in a Group of ALS Patients: Analysis with Demographic and Neuropsychological Data
Authors: M. Testa, L. Peotta, S. Giusiano, B. Lazzolino, U. Manera, A. Canosa, M. Grassano, F. Palumbo, A. Bombaci, S. Cabras, F. Di Pede, L. Solero, E. Matteoni, C. Moglia, A. Calvo, A. Chio
Abstract:
Amyotrophic Lateral Sclerosis (ALS) is a neurodegenerative disease of adulthood, which primarily affects the central nervous system and is characterized by progressive bilateral degeneration of motor neurons. The degeneration processes in ALS extend far beyond the neurons of the motor system, and affects cognition, behaviour and language. To outline the prevalence of language deficits in an ALS cohort and explore their profile along with demographic and neuropsychological data. A full neuropsychological battery and language assessment was administered to 56 ALS patients. Neuropsychological assessment included tests of executive functioning, verbal fluency, social cognition and memory. Language was assessed using tests for verbal comprehension, production and pragmatics. Patients were cognitively classified following the Revised Consensus Criteria and divided in three groups showing different levels of language deficits: group 1 - no language deficit; group 2 - one language deficit; group 3 - two or more language deficits. Chi-square for independence and non-parametric measures to compare groups were applied. Nearly half of ALS-CN patients (48%) reported one language test under the clinical cut-off, and only 13% of patents classified as ALS-CI showed no language deficits, while the rest 87% of ALS-CI reported two or more language deficits. ALS-BI and ALS-CBI cases all reported two or more language deficits. Deficits in production and in comprehension appeared more frequent in ALS-CI patients (p=0.011, p=0.003 respectively), with a higher percentage of comprehension deficits (83%). Nearly all ALS-CI reported at least one deficit in pragmatic abilities (96%) and all ALS-BI and ALS-CBI patients showed pragmatic deficits. Males showed higher percentage of pragmatic deficits (97%, p=0.007). No significant differences in language deficits have been found between bulbar and spinal onset. Months from onset and level of impairment at testing (ALS-FRS total score) were not significantly different between levels and type of language impairment. Age and education were significantly higher for cases showing no deficits in comprehension and pragmatics and in the group showing no language deficits. Comparing performances at neuropsychological tests among the three levels of language deficits, no significant differences in neuropsychological performances were found between group 1 and 2; compared to group 1, group 3 appeared to decay specifically on executive testing, verbal/visuospatial learning, and social cognition. Compared to group 2, group 3 showed worse performances specifically in tests of working memory and attention. Language deficits have found to be spread in our sample, encompassing verbal comprehension, production and pragmatics. Our study reveals that also cognitive intact patients (ALS-CN) showed at least one language deficit in 48% of cases. Pragmatic domain is the most compromised (84% of the total sample), present in nearly all ALS-CI (96%), likely due to the influence of executive impairment. Lower age and higher education seem to preserve comprehension, pragmatics and presence of language deficits. Finally, executive functions, verbal/visuospatial learning and social cognition differentiate the group with no language deficits from the group with a clinical language impairment (group 3), while attention and working memory differentiate the group with one language deficit from the clinical impaired group.Keywords: amyotrophic lateral sclerosis, language assessment, neuropsychological assessment, language deficit
Procedia PDF Downloads 15311888 Decomposing the Socio-Economic Inequalities in Utilization of Antenatal Care in South Asian Countries: Insight from Demographic and Health Survey
Authors: Jeetendra Yadav, Geetha Menon, Anita Pal, Rajkumar Verma
Abstract:
Even after encouraging maternal and child wellness programs at worldwide level, lower-middle income nations are not reached the goal set by the UN yet. This study quantified the contribution of socioeconomic determinants of inequality to the utilization of Antenatal Care in South Asian Countries. This study used data from Demographic Health Survey (DHS) of the selected countries were used, and Oaxaca decomposing were applied for socioeconomic inequalities in utilization of antenatal care. Finding from the multivariate analysis shows that mother’s age at the time of birth, birth order and interval, mother’s education, mass media exposure and economic status were significant determinants of the utilization of antenatal care services in South Asian countries. Considering, concentration index curve, the line of equity was greatest in Pakistan which followed by India and Nepal.Keywords: antenatal care, decomposition, inequalities, South Asian countries
Procedia PDF Downloads 17511887 A Model of the Adoption of Maritime Autonomous Surface Ship
Authors: Chin-Shan Lu, Yi-Pei Liu
Abstract:
This study examines the factors influencing the adoption of MASS in Taiwan's shipping industry. Digital technology and unmanned vehicle advancements have enhanced efficiency and reduced environmental impact in the shipping industry. The IMO has set regulations to promote low-carbon emissions and autonomous ship technology. Using the TOE framework and DOI theory, a research model was constructed, and data from 132 Taiwanese shipping companies were collected via a questionnaire survey. A structural equation modeling (SEM) was conducted to examine the relationships between variables. Results show that technological and environmental factors significantly influence operators' attitudes toward MASS, while organizational factors impact their willingness to adopt. Enhancing technological support, internal resource allocation, top management support, and cost management are crucial for promoting adoption. This study identifies key factors and provides recommendations for adopting autonomous ships in Taiwan's shipping industry.Keywords: MASS, technology-organization-environment, diffusion of innovations theory, shipping industry
Procedia PDF Downloads 1111886 Monitoring of Belt-Drive Defects Using the Vibration Signals and Simulation Models
Authors: A. Nabhan, Mohamed R. El-Sharkawy, A. Rashed
Abstract:
The main aim of this paper is to dedicate the belt drive system faults like cogs missing, misalignment and belt worm using vibration analysis technique. Experimentally, the belt drive test-rig is equipped to measure vibrations signals under different operating conditions. Finite element 3D model of belt drive system is created and vibration response analyzed using commercial finite element software ABAQUS/CAE. Root mean square (RMS) and Crest Factor will serve as indicators of average amplitude of envelope analysis signals. The vibration signals pattern obtained from the simulation model and experimental data have the same characteristics. It can be concluded that each case of the RMS is more effective in detecting the defect for acceleration response. While Crest Factor parameter has a response with the displacement and velocity of vibration signals. Also it can be noticed that the model has difficulty in completing the solution when the misalignment angle is higher than 1 degree.Keywords: simulation model, misalignment, cogs missing, vibration analysis
Procedia PDF Downloads 28211885 A Distributed Smart Battery Management System – sBMS, for Stationary Energy Storage Applications
Authors: António J. Gano, Carmen Rangel
Abstract:
Currently, electric energy storage systems for stationary applications have known an increasing interest, namely with the integration of local renewable energy power sources into energy communities. Li-ion batteries are considered the leading electric storage devices to achieve this integration, and Battery Management Systems (BMS) are decisive for their control and optimum performance. In this work, the advancement of a smart BMS (sBMS) prototype with a modular distributed topology is described. The system, still under development, has a distributed architecture with modular characteristics to operate with different battery pack topologies and charge capacities, integrating adaptive algorithms for functional state real-time monitoring and management of multicellular Li-ion batteries, and is intended for application in the context of a local energy community fed by renewable energy sources. This sBMS system includes different developed hardware units: (1) Cell monitoring units (CMUs) for interfacing with each individual cell or module monitoring within the battery pack; (2) Battery monitoring and switching unit (BMU) for global battery pack monitoring, thermal control and functional operating state switching; (3) Main management and local control unit (MCU) for local sBMS’s management and control, also serving as a communications gateway to external systems and devices. This architecture is fully expandable to battery packs with a large number of cells, or modules, interconnected in series, as the several units have local data acquisition and processing capabilities, communicating over a standard CAN bus and will be able to operate almost autonomously. The CMU units are intended to be used with Li-ion cells but can be used with other cell chemistries, with output voltages within the 2.5 to 5 V range. The different unit’s characteristics and specifications are described, including the different implemented hardware solutions. The developed hardware supports both passive and active methods for charge equalization, considered fundamental functionalities for optimizing the performance and the useful lifetime of a Li-ion battery package. The functional characteristics of the different units of this sBMS system, including different process variables data acquisition using a flexible set of sensors, can support the development of custom algorithms for estimating the parameters defining the functional states of the battery pack (State-of-Charge, State-of-Health, etc.) as well as different charge equalizing strategies and algorithms. This sBMS system is intended to interface with other systems and devices using standard communication protocols, like those used by the Internet of Things. In the future, this sBMS architecture can evolve to a fully decentralized topology, with all the units using Wi-Fi protocols and integrating a mesh network, making unnecessary the MCU unit. The status of the work in progress is reported, leading to conclusions on the system already executed, considering the implemented hardware solution, not only as fully functional advanced and configurable battery management system but also as a platform for developing custom algorithms and optimizing strategies to achieve better performance of electric energy stationary storage devices.Keywords: Li-ion battery, smart BMS, stationary electric storage, distributed BMS
Procedia PDF Downloads 9011884 Measurements of Recovery Stress and Recovery Strain of Ni-Based Shape Memory Alloys
Authors: W. J. Kim
Abstract:
The behaviors of the recovery stress and strain of an ultrafine-grained Ni-50.2 at.% Ti alloy prepared by high-ratio differential speed rolling (HRDSR) were examined by a specially designed tensile-testing set up, and the factors that influence the recovery stress and strain were studied. After HRDSR, both the recovery stress and strain were enhanced compared to the initial condition. The constitutive equation showing that the maximum recovery stress is a sole function of the recovery strain was developed based on the experimental data. The recovery strain increased as the yield stress increased. The maximum recovery stress increased with an increase in yield stress. The residual recovery stress was affected by the yield stress as well as the austenite-to-martensite transformation temperature. As the yield stress increased and as the martensitic transformation temperature decreased, the residual recovery stress increased.Keywords: high-ratio differential speed rolling, tensile testing, severe plastic deformation, shape memory alloys
Procedia PDF Downloads 35911883 The Moderating Effects of Attachment Style on the Relationship between the Psychological Symptoms and Well-Being of Mental Health Practitioners in Rehabilitation Centers: A Preliminary Study
Authors: Amaba, Marinela C., Espino, Gianne Ericka S. J. Valencia, Zeia Beatriz C.
Abstract:
This study aims to determine the moderating role of attachment style on the relationship between psychological symptoms and well-being of mental health practitioners in rehabilitation centers that are accredited of the Department of Health in Pampanga. Using the data gathered from 46 mental health practitioners, multiple regression models were conducted to test the main and moderating effects of attachment styles. The findings show that all three psychological symptoms namely depression, anxiety, and stress have main effects on their general well-being on a negative direction. However, attachment style did not moderate the relationship between the psychological symptoms and general well-being. On one hand, results about the relationship of psychological symptoms and well-being are consistent to previous findings of other studies while on the other hand, results in moderation were contradicting.Keywords: attachment style, psychological symptoms, well-being, mental health practitioners, rehabilitation centers
Procedia PDF Downloads 54611882 Identification of Conserved Domains and Motifs for GRF Gene Family
Authors: Jafar Ahmadi, Nafiseh Noormohammadi, Sedegeh Fabriki Ourang
Abstract:
GRF, Growth regulating factor, genes encode a novel class of plant-specific transcription factors. The GRF proteins play a role in the regulation of cell numbers in young and growing tissues and may act as transcription activations in growth and development of plants. Identification of GRF genes and their expression are important in plants to performance of the growth and development of various organs. In this study, to better understanding the structural and functional differences of GRFs family, 45 GRF proteins sequences in A. thaliana, Z. mays, O. sativa, B. napus, B. rapa, H. vulgare, and S. bicolor, have been collected and analyzed through bioinformatics data mining. As a result, in secondary structure of GRFs, the number of alpha helices was more than beta sheets and in all of them QLQ domains were completely in the biggest alpha helix. In all GRFs, QLQ, and WRC domains were completely protected except in AtGRF9. These proteins have no trans-membrane domain and due to have nuclear localization signals act in nuclear and they are component of unstable proteins in the test tube.Keywords: domain, gene family, GRF, motif
Procedia PDF Downloads 45311881 Ethnobotanical Study of Medicinal Plants of Leguminosae in Kantharalak Community Forest, Si Sa Ket Province, Thailand
Authors: W. Promprom, W. Chatan
Abstract:
Leguminosae is a large plant family and its members are important for local people utilization in the Northeast of Thailand. This research aimed to survey medicinal plants in this family in Kantharalak Community forest. The plant collection and exploration were made from October 2017 to September 2018. Folk medicinal uses were studied by interviewing villagers and folk medicine healers living around the community forest by asking about local names, using parts, preparation and properties. The results showed that 65 species belonging to 40 genera were found. Among these, 30 species were medicinal plant. The most used plant parts were leaf. Decoction and drinking were mostly preparation method and administration mode used. All medicinal plants could be categorized into 17 diseases/symptoms. Most plant (56.66%) were used for fever. The voucher specimens were deposited in Department of Biology, Faculty of Science, Mahasarakham University, Thailand. Therefore, the data from this study might be widely used by the local area and further scientific study.Keywords: ethnobotany, ethnophamacology, medicinal plant, taxonomy, utilization
Procedia PDF Downloads 14811880 Ethnic Conflict Dynamics in the Ethiopian Federation: Case of the Oromo-Somali Conflict
Authors: Takele Bekele Bayu
Abstract:
Though Ethiopia is an ancient country with ethnocultural and linguistic diversity, modern Ethiopia came into being in the second half of the 19th century under the military expansion of King Menelik II. Since then, the subsequent political system in the country failed to recognize and accommodate the country’s ethnolinguistic diversity. However, in 1991 the new government led by the Ethiopian People's Revolutionary Democratic Front (EPRDF) adopted federal-state structuring whereby constitutionally recognized and institutionally accommodated the country’s diversity. This investigation aimed to analyze drivers of ethnic conflict and its dynamism along the Eastern shared border of the Somali and Oromia regional administrations within the federal framework. The paper employed a comparative research design, adopted mixed research methods, and used survey questionnaires and focus group discussions (FGDs) for data collection. The study found that the Somali-Oromo conflict is complex and the dynamics and the sources of conflict in the study areas are similar.Keywords: Ethiopia, Oromo, Somali, ethnic conflict, federalism
Procedia PDF Downloads 6911879 Factor to Elicit Spatial Presence: Calmness
Authors: Nadia Diyana Mohd Muhaiyuddin, Dayang Rohaya Awang Rambli
Abstract:
The aim of our work is to identify whether user’s calmness can be a factor to elicit user’s spatial presence experience. Hence, a systematic mental model technique called repertory grid was selected to collect data because users can freely give their opinions in this approach. Three image-based virtual reality (IBVR) environments were created to satisfy the requirement of the repertory grid. Different virtual environments were necessary to allow users to compare and give feedback. Result was analyzed by using descriptive analysis through the SPSS software. The result revealed that ‘users feel calm’ is accepted as one of the factors that can elicit spatial presence. Users also highlighted five IBVR characteristics that could elicit spatial presence, namely, calm sound, calm content, calm color, calm story line, and the calm feeling of the user.Keywords: spatial presence, presence, virtual reality, image-based virtual reality, human-computer interaction
Procedia PDF Downloads 28211878 Diabatic Flow of Sub-Cooled R-600a Inside a Capillary Tube: Concentric Configuration
Authors: Ravi Kumar, Santhosh Kumar Dubba
Abstract:
This paper presents an experimental study of a diabatic flow of R-600a through a concentric configured capillary tube suction line heat exchanger. The details of experimental facility for testing the diabatic capillary tube with different inlet sub-cooling degree and pressure are discussed. The effect of coil diameter, capillary length, capillary tube diameter, sub-cooling degree and inlet pressure on mass flow rate are presented. The degree of sub-cooling at the inlet of capillary tube is varied from 3-20°C. The refrigerant mass flow rate is scattered up with rising of pressure. A semi-empirical correlation to predict the mass flow rate of R-600a flowing through a diabatic capillary tube is proposed for sub-cooled inlet conditions. The proposed correlation predicts measured data with an error band of ±20 percent.Keywords: diabatic, capillary tube, concentric, R-600a
Procedia PDF Downloads 20111877 W-WING: Aeroelastic Demonstrator for Experimental Investigation into Whirl Flutter
Authors: Jiri Cecrdle
Abstract:
This paper describes the concept of the W-WING whirl flutter aeroelastic demonstrator. Whirl flutter is the specific case of flutter that accounts for the additional dynamic and aerodynamic influences of the engine rotating parts. The instability is driven by motion-induced unsteady aerodynamic propeller forces and moments acting in the propeller plane. Whirl flutter instability is a serious problem that may cause the unstable vibration of a propeller mounting, leading to the failure of an engine installation or an entire wing. The complicated physical principle of whirl flutter required the experimental validation of the analytically gained results. W-WING aeroelastic demonstrator has been designed and developed at Czech Aerospace Research Centre (VZLU) Prague, Czechia. The demonstrator represents the wing and engine of the twin turboprop commuter aircraft. Contrary to the most of past demonstrators, it includes a powered motor and thrusting propeller. It allows the changes of the main structural parameters influencing the whirl flutter stability characteristics. Propeller blades are adjustable at standstill. The demonstrator is instrumented by strain gauges, accelerometers, revolution-counting impulse sensor, sensor of airflow velocity, and the thrust measurement unit. Measurement is supported by the in house program providing the data storage and real-time depiction in the time domain as well as pre-processing into the form of the power spectral densities. The engine is linked with a servo-drive unit, which enables maintaining of the propeller revolutions (constant or controlled rate ramp) and monitoring of immediate revolutions and power. Furthermore, the program manages the aerodynamic excitation of the demonstrator by the aileron flapping (constant, sweep, impulse). Finally, it provides the safety guard to prevent any structural failure of the demonstrator hardware. In addition, LMS TestLab system is used for the measurement of the structure response and for the data assessment by means of the FFT- and OMA-based methods. The demonstrator is intended for the experimental investigations in the VZLU 3m-diameter low-speed wind tunnel. The measurement variant of the model is defined by the structural parameters: pitch and yaw attachment stiffness, pitch and yaw hinge stations, balance weight station, propeller type (duralumin or steel blades), and finally, angle of attack of the propeller blade 75% section (). The excitation is provided either by the airflow turbulence or by means of the aerodynamic excitation by the aileron flapping using a frequency harmonic sweep. The experimental results are planned to be utilized for validation of analytical methods and software tools in the frame of development of the new complex multi-blade twin-rotor propulsion system for the new generation regional aircraft. Experimental campaigns will include measurements of aerodynamic derivatives and measurements of stability boundaries for various configurations of the demonstrator.Keywords: aeroelasticity, flutter, whirl flutter, W WING demonstrator
Procedia PDF Downloads 8711876 Comparative Study of Medical and Fine Art Students on the Level of Perceived Stress and Coping Skills
Authors: Bushra Mussawar, Saleha Younus
Abstract:
Students often view their academic life demanding and stressful. However, apart from academics, stress springs from various other sources namely, finance, family, health, friends etc. The present study aims to assess the level of perceived stress in medical and fine arts students, and to determine the coping strategies used by the students to mitigate stress. The sample of the study consisted of 178 medical and fine arts students. The sample was selected through purposive sampling. Pearson correlation coefficient and T-test were used to analyze data. Results of the study revealed that there exists a positive relationship between perceived stress and coping strategies. Additionally, the two groups showed marked differences in terms of stress perception and coping styles. The level of perceived stress was found to be high in medical students nonetheless, they employed more positive coping strategies than fine arts students who scored high on negative coping strategies which are deleterious to the overall wellbeing.Keywords: perceived stress, coping strategies, medical, fine arts students
Procedia PDF Downloads 29911875 Importance of Hospitality In Tourism Industry
Authors: S M Abdus Sattar
Abstract:
Introduction: The tourism industry is a vital component of economies, providing opportunities for economic growth and cultural exchange. At the heart of this industry lies the concept of hospitality. Tourism refers to the activity of traveling for leisure or business and hospitality refers to the welcoming, amenities and providing of services to guests in the travel and accommodation industries. Tourism is one of the fastest growing industries in the world today. Objectives: The most important objective of Tourism and Hospitality study are: To assess different aspects, To identify the reasons, To analyze the contribution in GDP of Bangladesh, To identify importances of hospitality, To identify challenges, To Development of leadership characteristics, communication, teamwork skill, customer service and problem-solving, To provide welcoming treatment to guests, offering accommodation, food, transportation and entertainment services to ensure guests feel safe and comfortable away from home, To explore future prospects in Bangladesh and To suggests some recommendations for development of these sector. Methodology: Statistical method has been adopted in this study. Common characteristics of the people of particular area are found out. Tourism data is collected through various methods, such as surveys, interviews, visitor registration, travel agency records, hotel bookings, transport ticketing systems, online platforms, social media, Bangladesh Tourism Corporation, World Travel and Tourism Council, Quantitative and qualitative research methods are used while collecting and analyzing data. Findings: Tourism and Hospitality focuses on marketing, management, attractions, recreation events, travel related services, lodging, operations of restaurants and food services. Tourism offers great opportunities for emerging economies and developing countries. It creates jobs, strengthens the local economy, contributes to local infrastructure development, can help to conserve the natural environment, cultural assets, traditions, reduce poverty and inequality. The hospitality industry contributes to the economy of a country by employing its human resources. It generates new employment, contributing to the Gross Domestic Product (GDP) of a country. Around 330 million people were employed in the Tourism and Hospitality sector in globally. Tourism and Hospitality industry is creating high tax revenues. Tourism is a rising industry in Bangladesh. Studying hospitality can also help develop a range of essential skills that are valuable in any industry. Conclusion: As the conclusion, tourism industry is focused on providing quality attractions and events in order to entice tourists to come. The hospitality industry provides the good service for client. Hospitality and Tourism are closely related. Hospitality built up the relationship between host and guest. The importance of hospitality in tourism industry is immense. The Tourism and Hospitality industry is an important contributor to Bangladesh's economy. It is necessary to develop the Tourism infrastructure, maintain tourist destinations, railway stations, airports, rest house, hotels and improve the quality of services.Keywords: tourism, hospitality, GDP, employment, economy
Procedia PDF Downloads 811874 Determinants of Corporate Social Responsibility Adoption: Evidence from China
Authors: Jing (Claire) LI
Abstract:
More than two decades from 2000 to 2020 of economic reforms have brought China unprecedented economic growth. There is an urgent call of research towards corporate social responsibility (CSR) in the context of China because while China continues to develop into a global trading market, it suffers from various serious problems relating to CSR. This study analyses the factors affecting the adoption of CSR practices by Chinese listed companies. The author proposes a new framework of factors of CSR adoption. Following common organisational factors and external factors in the literature (including organisational support, company size, shareholder pressures, and government support), this study introduces two additional factors, dynamic capability and regional culture. A survey questionnaire was conducted on the CSR adoption of Chinese listed companies in Shen Zhen and Shang Hai index from December 2019 to March 2020. The survey was conducted to collect data on the factors that affect the adoption of CSR. After collection of data, this study performed factor analysis to reduce the number of measurement items to several main factors. This procedure is to confirm the proposed framework and ensure the significant factors. Through analysis, this study identifies four grouped factors as determinants of the CSR adoption. The first factor loading includes dynamic capability and organisational support. The study finds that they are positively related to the first factor, so the first factor mainly reflects the capabilities of companies, which is one component in internal factors. In the second factor, measurement items of stakeholder pressures mainly are from regulatory bodies, customer and supplier, employees and community, and shareholders. In sum, they are positively related to the second factor and they reflect stakeholder pressures, which is one component of external factors. The third factor reflects organisational characteristics. Variables include company size and cultural score. Among these variables, company size is negatively related to the third factor. The resulted factor loading of the third factor implies that organisational factor is an important determinant of CSR adoption. Cultural consistency, the variable in the fourth factor, is positively related to the factor. It represents the difference between perception of managers and actual culture of the organisations in terms of cultural dimensions, which is one component in internal factors. It implies that regional culture is an important factor of CSR adoption. Overall, the results are consistent with previous literature. This study is of significance from both theoretical and empirical perspectives. First, from the significance of theoretical perspective, this research combines stakeholder theory, dynamic capability view of a firm, and neo-institutional theory in CSR research. Based on association of these three theories, this study introduces two new factors (dynamic capability and regional culture) to have a better framework for CSR adoption. Second, this study contributes to empirical literature of CSR in the context of China. Extant Chinese companies lack recognition of the importance of CSR practices adoption. This study built a framework and may help companies to design resource allocation strategies and evaluate future CSR and management practices in an early stage.Keywords: China, corporate social responsibility, CSR adoption, dynamic capability, regional culture
Procedia PDF Downloads 12911873 A Chinese Nested Named Entity Recognition Model Based on Lexical Features
Abstract:
In the field of named entity recognition, most of the research has been conducted around simple entities. However, for nested named entities, which still contain entities within entities, it has been difficult to identify them accurately due to their boundary ambiguity. In this paper, a hierarchical recognition model is constructed based on the grammatical structure and semantic features of Chinese text for boundary calculation based on lexical features. The analysis is carried out at different levels in terms of granularity, semantics, and lexicality, respectively, avoiding repetitive work to reduce computational effort and using the semantic features of words to calculate the boundaries of entities to improve the accuracy of the recognition work. The results of the experiments carried out on web-based microblogging data show that the model achieves an accuracy of 86.33% and an F1 value of 89.27% in recognizing nested named entities, making up for the shortcomings of some previous recognition models and improving the efficiency of recognition of nested named entities.Keywords: coarse-grained, nested named entity, Chinese natural language processing, word embedding, T-SNE dimensionality reduction algorithm
Procedia PDF Downloads 12111872 Study of Intermolecular Interactions in Binary Mixtures of 1-Butyl-3-Methyl Imidazolium Bis (Trifluoro Methyl Sulfonyl) Imide and 1-Ethyl-3-Methyl Imidazolium Ethyl Sulphate at Different Temperature from 293.18 to 342.15 K
Authors: V. Lokesh, M. Manjunathan, S. Sairam, K. Saithsh Kumar, R. Anantharaj
Abstract:
The densities of pure and its binary mixtures of 1-Butyl-3-methyl imidazolium bis (trifluoro methyl sulfonyl) imide and 1–Ethyl-3-methyl imidazolium ethyl sulphate at different temperature, over the entire composition range were measured at 293.15, 298.15, 303.15, 308.15, 313.15, 318.15, 323.15, 328.15, 33.15, 338.15, 343.15 K. In this study, the liquid-liquid extraction procedure was used. From this experimental data, the excess molar volumes, apparent molar volume, partial molar volumes and the excess partial molar volumes have been calculated for over the whole composition range. Hence, the effect of temperature and composition on all derived thermodynamic properties of this binary mixture will be discussed in terms of intermolecular interactions.Keywords: ionic liquid, interaction energy, effect of temperature, effect of composition
Procedia PDF Downloads 16711871 Thai Tourists’ Satisfaction and Tourist’s Decision Making Process in Southern of Thailand
Authors: Rewadee Waiyawassana
Abstract:
The objectives of the research on Thai tourists’ satisfaction of visiting Southern of Thailand are i) to study the Thai tourists’ satisfaction who select southern of Thailand as their destinations ii) to study their tourist’s decision making process in Southern of Thailand. The samples of the study are 619 Thai visitors at Southern of Thailand by accidental sampling technic and focus group interview for 12 key informant by purposive sampling. The data analysis includes Percentage, Frequency and One-way ANOVA. The findings from the research are the satisfaction of Thai visitors on southern of Thailand ranks from the resources of the destination, transportation, convenience, security, and promotion and public relations; with the high level of satisfaction on all the factors the government or responsible agencies should also modernize the marketing and public relation with increasing public relations, the potential visitors shall be updated with new information and alternative tourist destination also.Keywords: public relations, Southern of Thailand, Thai Tourists’ satisfaction, Tourist’s decision making process
Procedia PDF Downloads 31611870 Theoretical Investigation of the Structural, Electronic, Optical and Elastic Properties of the Perovskite ScRhO₃
Authors: L. Foudia, K. Haddadi, M. Reffas
Abstract:
First principles study of structural, elastic, electronic and optical properties of the monoclinic perovskite type ScRhO₃ has been reported using the pseudo-potential plane wave method within the local density approximation. The calculated lattice parameters, including the lattice constants and angle β are in excellent agreement with the available experimental data, which proving the reliability of the chosen theoretical approach. Pressure dependence up to 20 GPa of the single crystal and polycrystalline elastic constants has been investigated in details using the strain-stress approach. The mechanical stability, ductility, average elastic wave velocity, Debye temperature and elastic anisotropy were also assessed. Electronic band structure and density of states (DOS) demonstrated its semiconducting nature showing a direct band gap of 1.38 eV. Furthermore, several optical properties, such as absorption coefficient, reflectivity, refractive index, dielectric function, optical conductivity and electron energy loss function have been calculated for radiation up to 40 eV.Keywords: ab-initio, perovskite, DFT, band gap.
Procedia PDF Downloads 6711869 The Effects of Infographics as a Supplementary Tool in Promoting Academic Reading Skill in an EFL Class
Authors: Niracha Chompurach, Dararat Khampusaen
Abstract:
EFL students have to be able to synthesize the texts they are reading critically to compose and connect the information. This study focuses on the effects of the application of Infographics as a supplementary tool to improve Thai EFL students’ Academic reading skills. Infographics are graphic visual representations of information, data, and knowledge offering students to work on gathering multiple types of information, such as pictures, texts, graphs, mapping, and charts. The study aims to investigate if the Infographics as a supplementary tool in academic reading lessons can make a difference in students’ reading skills, and the students’ opinions toward the application of infographics as a reading tool. The participants of this study were 3rd year Thai EFL Khon Kaen University students who took English Academic Reading course. This study employed Infographics assignments, Infographics rubric, and Gucus group interview. This study would advantage for both EFL teachers and students as a means to engage the students to handle the larger load of and represents the complex information in visible and comprehensible way.Keywords: EFL, e-learning, infographics, language education
Procedia PDF Downloads 16011868 The Organizational Behavior that Affect to the Work Motivation in the Dusit Workplace
Authors: Suvimon Wajeetongratana, Prateep Wajeetongratana
Abstract:
The purpose of this research will study the organizational behavior including self-efficacy, hope, optimism, and resiliency that affect to the work motivation in the Dusit workplace and the sample consisted of the production workers in a private company in Dusit area for four hundred workers with approximately 10,000 employees and in this study will provide the multiple regression analysis was used to analyze the questionnaire survey data. The results of the analysis indicate the latent core confidence factor derived from the four components of self-efficacy, hope, optimism, and resiliency provided a significant positive impact on performance. The impact of the integrated latent core confidence factor was, in fact, more effective than derived from any one individual component, as well as any core trait-like self-evaluations such as self-esteem, general efficacy, internal locus of control, and emotional stability.Keywords: firm performance effectiveness, organizational behavior, work motivation, Dusit workplace
Procedia PDF Downloads 36711867 Organizational Socialization Levels in Nurses
Authors: Manar Aslan, Ayfer Karaaslan, Serap Selçuk
Abstract:
The research was conducted in order to determine the organizational socialization levels of nurses working in hospitals in the form of a descriptive study. The research population was composed of nurses employed in public and private sector hospitals in the province of Konya with 0-3 years of professional experience in the hospitals (N=1200); and the sample was composed of 495 nurses that accepted to take part in the study voluntarily. Organizational Socialization Scale which was developed by Haueter, Macan and Winter (2003) and whose validity-reliability in Turkish was analyzed by Ataman (2012) was used. Statistical evaluation of data was conducted in SPSS.16 software. The results of the study revealed that the total score taken by nurses at the organizational socialization scale was 262.95; and this was close to the maximum score. Particularly the departmental socialization sub-dimension proved to be higher in comparison to the other two dimensions (organization socialization and task socialization). Statistically meaningful differences were found in the levels of organization socialization in relation to the status of organizational orientation training, level of education and age group.Keywords: nurses, newcomers, organizational socialization, total score
Procedia PDF Downloads 34111866 Runtime Monitoring Using Policy-Based Approach to Control Information Flow for Mobile Apps
Authors: Mohamed Sarrab, Hadj Bourdoucen
Abstract:
Mobile applications are verified to check the correctness or evaluated to check the performance with respect to specific security properties such as availability, integrity, and confidentiality. Where they are made available to the end users of the mobile application is achievable only to a limited degree using software engineering static verification techniques. The more sensitive the information, such as credit card data, personal medical information or personal emails being processed by mobile application, the more important it is to ensure the confidentiality of this information. Monitoring non-trusted mobile application during execution in an environment where sensitive information is present is difficult and unnerving. The paper addresses the issue of monitoring and controlling the flow of confidential information during non-trusted mobile application execution. The approach concentrates on providing a dynamic and usable information security solution by interacting with the mobile users during the run-time of mobile application in response to information flow events.Keywords: mobile application, run-time verification, usable security, direct information flow
Procedia PDF Downloads 37111865 Investigation of Software Integration for Simulations of Buoyancy-Driven Heat Transfer in a Vehicle Underhood during Thermal Soak
Authors: R. Yuan, S. Sivasankaran, N. Dutta, K. Ebrahimi
Abstract:
This paper investigates the software capability and computer-aided engineering (CAE) method of modelling transient heat transfer process occurred in the vehicle underhood region during vehicle thermal soak phase. The heat retention from the soak period will be beneficial to the cold start with reduced friction loss for the second 14°C worldwide harmonized light-duty vehicle test procedure (WLTP) cycle, therefore provides benefits on both CO₂ emission reduction and fuel economy. When vehicle undergoes soak stage, the airflow and the associated convective heat transfer around and inside the engine bay is driven by the buoyancy effect. This effect along with thermal radiation and conduction are the key factors to the thermal simulation of the engine bay to obtain the accurate fluids and metal temperature cool-down trajectories and to predict the temperatures at the end of the soak period. Method development has been investigated in this study on a light-duty passenger vehicle using coupled aerodynamic-heat transfer thermal transient modelling method for the full vehicle under 9 hours of thermal soak. The 3D underhood flow dynamics were solved inherently transient by the Lattice-Boltzmann Method (LBM) method using the PowerFlow software. This was further coupled with heat transfer modelling using the PowerTHERM software provided by Exa Corporation. The particle-based LBM method was capable of accurately handling extremely complicated transient flow behavior on complex surface geometries. The detailed thermal modelling, including heat conduction, radiation, and buoyancy-driven heat convection, were integrated solved by PowerTHERM. The 9 hours cool-down period was simulated and compared with the vehicle testing data of the key fluid (coolant, oil) and metal temperatures. The developed CAE method was able to predict the cool-down behaviour of the key fluids and components in agreement with the experimental data and also visualised the air leakage paths and thermal retention around the engine bay. The cool-down trajectories of the key components obtained for the 9 hours thermal soak period provide vital information and a basis for the further development of reduced-order modelling studies in future work. This allows a fast-running model to be developed and be further imbedded with the holistic study of vehicle energy modelling and thermal management. It is also found that the buoyancy effect plays an important part at the first stage of the 9 hours soak and the flow development during this stage is vital to accurately predict the heat transfer coefficients for the heat retention modelling. The developed method has demonstrated the software integration for simulating buoyancy-driven heat transfer in a vehicle underhood region during thermal soak with satisfying accuracy and efficient computing time. The CAE method developed will allow integration of the design of engine encapsulations for improving fuel consumption and reducing CO₂ emissions in a timely and robust manner, aiding the development of low-carbon transport technologies.Keywords: ATCT/WLTC driving cycle, buoyancy-driven heat transfer, CAE method, heat retention, underhood modeling, vehicle thermal soak
Procedia PDF Downloads 146