Search results for: causes of construction project delays

Authors: Byeong-Sam Kim, Kyeongwoo Park

Abstract:

In this study, induced structural optimization is performed to compare the trade-off between wing weight and induced drag for wing panel extensions, construction of wing panel and winglets. The aerostructural optimization problem consists of parameters with strength condition, and two maneuver conditions using residual stresses in panel production. The results of kinematic motion analysis presented a homogenization based theory for 3D beams and 3D shells for wing panel. This theory uses a kinematic description of the beam based on normalized displacement moments. The displacement of the wing is a significant design consideration as large deflections lead to large stresses and increased fatigue of components cause residual stresses. The stresses in the wing panel are small compared to the yield stress of aluminum alloy. This study describes the implementation of a large wing panel, aerostructural analysis and structural parameters optimization framework that couples a three-dimensional panel method.

Keywords: wing panel, aerostructural optimization, FEM, structural analysis

Procedia PDF Downloads 566

Authors: Mohammad Ruhul Amin, Nusrat Jahan

Abstract:

Natural gas is a cleaner fuel compared to the others. But it needs some treatment before it is in a state to be used. So natural gas purification is an integral part of any process where natural gas is used as raw material or fuel. There are several impurities in natural gas that have to be removed before use. CO2 is one of the major contaminants. In this project we have removed CO2 by amine process by using MEA solution. We have built up the whole amine process for removing CO2 in Aspen Hysys and simulated the process. At the end of simulation we have got very satisfactory results by using MEA solution for the removal of CO2. Simulation result shows that amine absorption process enables to reduce CO2 content from NG by 58%. HYSYS optimizer allowed us to get a perfect optimized plant. After optimization the profit of existing plant is increased by 2.34 %.Simulation and optimization by Aspen-HYSYS simulator makes available us to enormous information which will help us to further research in future.

Keywords: Aspen–Hysys, CO2 removal, flowsheet development, MEA solution, natural gas optimization

Procedia PDF Downloads 473

Authors: Peyman Amini Motlagh, Ali Pak

Abstract:

Seismic retrofitting of important structures is essential in seismological active zones. The importance is doubled when it comes to some buildings like schools, hospitals, bridges etc. because they are required to continue their serviceability even after a major earthquake. Generally, seismic retrofitting codes have paid little attention to retrofitting of foundations due to its construction complexity. In this paper different methods for seismic retrofitting of tall buildings’ foundations will be discussed and evaluated. Foundations are considered in three different categories. First, foundations those are in danger of liquefaction of their underlying soil. Second, foundations located on slopes in seismological active regions. Third, foundations designed according to former design codes and may show structural defects under earthquake loads. After describing different methods used in different countries for retrofitting of the existing foundations in seismological active regions, comprehensive comparison between these methods with regard to the above mentioned categories is carried out. This paper gives some guidelines to choose the best method for seismic retrofitting of tall buildings’ foundations in retrofitting projects.

Keywords: existing foundation, landslide, liquefaction, seismic retrofitting

Procedia PDF Downloads 377

Authors: Kyong-Ku Yun, Dae-Ae Kim, Kyeo-Re Lee, Kyong Namkung, Seung-Yeon Han

Abstract:

Micro silica is collected as a by-product of the silicon and ferrosilicon alloy production in electric arc furnace using highly pure quartz, wood chips, coke and the like. It consists of about 85% of silicon which has spherical particles with an average particle size of 150 μm. The bulk density of micro silica varies from 150 to 700kg/m^3 and the fineness ranges from 150,000 to 300,000cm^2/g. An amorphous structure with a high silicon oxide content of micro silica induces an active reaction with calcium hydroxide (Ca(OH)₂) generated by the cement hydrate of a large surface area (about 20 m^² / g), and they are also known to form calcium, silicate, hydrate conjugate (C-S-H). Micro silica tends to act as a filler because of the fine particles and the spherical shape. These particles do not get covered by water and they fit well in the space between the relatively rough cement grains which does not freely fluidize concrete. On the contrary, water demand increases since micro silica particles have a tendency to absorb water because of the large surface area. The overall effect of micro silica depends on the amount of micro silica added with other parameters in the water-(cement + micro silica) ratio, and the availability of superplasticizer. In this research, it was studied on cellular sprayed concrete. This method involves a direct re-production of ready mixed concrete into a high performance at a job site. It could reduce the cost of construction by an adding a cellular and a micro silica into a ready mixed concrete truck in a field. Also, micro silica which is difficult with mixing due to high fineness in the field can be added and dispersed in concrete by increasing the fluidity of ready mixed concrete through the surface activity of cellular. Increased air content is converged to a certain level of air content by spraying and it also produces high-performance concrete by remixing of powders in the process of spraying. As it does not use a field mixing equipment the cost of construction decrease and it can be constructed after installing special spray machine in a commercial pump car. Therefore, use of special equipment is minimized, providing economic feasibility through the utilization of existing equipment. This study was carried out to evaluate a highly reliable method of confirming dispersion through a high performance cellular sprayed concrete. A mixture of 25mm coarse aggregate and river sand was applied to the concrete. In addition, by applying silica fume and foam, silica fume dispersion is confirmed in accordance with foam mixing, and the mean and standard deviation is obtained. Then variation coefficient is calculated to finally evaluate the dispersion. Comparison and analysis of before and after spraying were conducted on the experiment variables of 21L, 35L foam for each 7%, 14% silica fume respectively. Taking foam and silica fume as variables, the experiment proceed. Casting a specimen for each variable, a five-day sample is taken from each specimen for EDS test. In this study, it was examined by an experiment materials, plan and mix design, test methods, and equipment, for the evaluation of dispersion in accordance with micro silica and foam.

Keywords: micro silica, distribution, ready mixed concrete, foam

Procedia PDF Downloads 195

Authors: Vanessa Do, Lauren Smith, Leslie Carver

Abstract:

It is widely known that individuals with autism spectrum disorder (ASD) may exhibit sensitivity to stimuli. Even at a young age, they tend to display stimuli-related discomfort in their behavior during play. Play serves a crucial role in a child’s early years as it helps support healthy brain development, socio-emotional skills, and adaptation to their environment There is research dedicated to studying infant preferences for toys, especially in regard to: gender preferences, the advantages of promoting play, and the caregiver’s role in their child’s play routines. However, there is a disproportionate amount of literature examining how play patterns may differ in children with sensory sensitivity, such as children diagnosed with ASD. Prior literature has studied and found supporting evidence that individuals with ASD have deficits in social communication and have increased presence of repetitive behaviors and/or restricted interests, which also display in early childhood play patterns. This study aims to examine potential differences in toy preference between infants with (FH+) and without (FH-) a familial history of ASD ages 6. 9, and 12 months old. More specifically, this study will address the question, “do FH+ infants tend to play more with toys that require less social engagement compared to FH- infants?” Infants and their caregivers were recruited and asked to engage in a free-play session in their homes that lasted approximately 5 minutes. The sessions were recorded and later coded offline for engagement behaviors categorized by toy; each toy that the infants interacted with was coded as belonging to one of 6 categories: sensory (designed to stimulate one or more senses such as light-up toys or musical toys) , construction (e.g., building blocks, rubber suction cups), vehicles (e.g., toy cars), instructional (require steps to accomplish a goal such as flip phones or books), imaginative (e.g., dolls, stuffed animals), and miscellaneous (toys that do not fit into these categories). Toy engagement was defined as the infant looking and touching the toy (ILT) or looking at the toy while their caregiver was holding it (IL-CT). Results reported include/will include the proportion of time the infant was actively engaged with the toy out of the total usable video time per subject — distractions observed during the session were excluded from analysis. Data collection is still ongoing; however, the prediction is that FH+ infants will have higher engagement with sensory and construction toys as they require the least amount of social effort. Furthermore, FH+ infants will have the least engagement with the imaginative toys as prior literature has supported the claim that individuals with ASD have a decreased likelihood to engage in play that requires pretend play and other social skills. Looking at what toys are more or less engaging to FH+ infants is important as it provides significant contributions to their healthy cognitive, social, and emotional development. As play is one of the first ways for a child to understand the complexities of the larger world, the findings of this study may help guide further research into encouraging play with toys that are more engaging and sensory-sensitive for children with ASD.

Keywords: autism engagement, children’s play, early development, free-play, infants, toy

Procedia PDF Downloads 200

Authors: Naim Karasekreter, Ugur Fidan, Fatih Basciftci

Abstract:

Wireless sensor networks are networks in which more than one sensor node is organized among themselves. The working principle is based on the transfer of the sensed data over the other nodes in the network to the central station. Wireless sensor networks concentrate on routing algorithms, energy efficiency and clustering algorithms. In the clustering method, the nodes in the network are divided into clusters using different parameters and the most suitable cluster head is selected from among them. The data to be sent to the center is sent per cluster, and the cluster head is transmitted to the center. With this method, the network traffic is reduced and the energy efficiency of the nodes is increased. In this study, clustering algorithms were examined in terms of clustering performances and cluster head selection characteristics to try to identify weak and strong sides. This work is supported by the Project 17.Kariyer.123 of Afyon Kocatepe University BAP Commission.

Keywords: wireless sensor networks (WSN), clustering algorithm, cluster head, clustering

Procedia PDF Downloads 486

Authors: Catharina O. Vianna Dias da Silva, Amanda F. Batista, Ana Clara C. Burgos Lessa, Carolina S. Lucchesi Ramacciotti, Maria Clara B. de Andrade, Roberto de B. Silva

Abstract:

This article aims to analyze the bioethical aspects related to the historical practices of experiments on humans that occurred in Nazi Germany during the period of World War II (1939-1945). The method was based on the bibliographic review of articles published in databases such as SciELO and Pubmed. In the discussion, historical and humanistic aspects that contributed to the construction of a genocidal culture practiced during this period were analyzed. Additionally, an ethical question arises: should the information acquired during this dark period be used by science? After analysis, it was found that these Nazi experiments went over medical and ethical principles, being a deplorable milestone in history. It was also concluded that, although they generated potentially 'useful' results in the scientific field, they should be discarded as an ethical question of principle, of never daring to validate such a deplorable way of obtaining knowledge.

Keywords: Nazism, bioethics, human experimentation, human rights, genocide, torture, medicine

Procedia PDF Downloads 144

Authors: Syfur Rahman, Mohammad J. Khattak

Abstract:

Every year a huge quantity of recycling concrete aggregate (RCA) is generated in the United States of America. Utilization of RCA can solve the storage problem, prevent environmental pollution, and reduce the construction cost. However, due to the overall low strength and durability characteristics of RCA, its usages are limited to a certain area like a landfill, low strength base material, replacement of a few percentages of virgin aggregates in Portland cement concrete, etc. This study focuses on the improvement of the strength and durability characteristics of RCA by introducing the concept of roller-compacted geopolymer concrete. In this research, developed roller-compacted geopolymer concrete (RCGPC) and roller-compacted cement concrete (RCC) mixtures containing 100% recycled concrete aggregate were evaluated and compared. Several selected RCGPC mixtures were investigated to find out the effect of mixture variables, including sodium hydroxide (NaOH) molar concentration, sodium silicate (Na₂SiO₃), to sodium hydroxide (NaOH) ratio on the strength, stiffness and durability characteristics of the developed RCGPC. Sodium hydroxide (NaOH) and sodium silicate (Na₂SiO₃) were mixed in different ratios to synthesize the alkali activator. American Concrete Pavement Association (ACPA) recommended RCC gradation was used with a maximum nominal aggregate size of 19 mm with a 4% fine particle passing 0.075 mm sieve. The mixtures were made using NaOH molar concentration of 8M and 10M along with, Na₂SiO₃ to NaOH ratio of 0 and 1 by mass and 15% class F fly ash. Optimum alkali content and moisture content were determined for each RCGPC and RCC mixtures, respectively, using modified proctor test. Compressive strength, semi-circular bending beam strength, and dynamic modulus test were conducted to evaluate the mechanistic characteristics of both mixtures. To determine the optimum curing conditions for RCGPC, effects of different curing temperature and curing duration on compressive strength were also studied. Sulphate attack and freeze-thaw tests were also carried out to assess the durability properties of the developed mixtures. X-ray diffraction (XRD) was used for morphology and microstructure analysis. From the optimum moisture content results, it was found that RCGPC has high alkali content, which was mainly due to the high absorption capacity of RCA. It was found that the mixtures with Na₂SiO₃ to NaOH ratio of 1 yielded about 60% higher compressive strength than the ratio of 0. Further, the mixtures using 10M NaOH concentrations and alkali ratio of 1 produced about 28 MPa of compressive strength, which was around 33% higher than 8M NaOH mixtures. Similar results were obtained for elastic and dynamic modulus of the mixtures. On the other hand, the semi-circular bending beam strength remained the same for both 8 and 10 molar NaOH geopolymer mixtures. Formation of new geopolymeric compounds and chemical bonds in the newly formed novel RCGPC mixtures were also discovered using XRD analysis. The results of mechanical and durability testing further revealed that RCGPC performed similarly to that of RCC mixtures. Based on the results of mechanical and durability testing, the developed RCGPC mixtures using 100% recycled concrete could be used as a cost-effective solution for the construction of pavement structures.

Keywords: roller compacted concrete, geopolymer concrete, recycled concrete aggregate, concrete pavement, fly ash

Procedia PDF Downloads 122

Authors: Hamide Amani, Afshin FarahBakhsh, Iman Farahbakhsh

Abstract:

In this paper, an amprometric biosensor based on surface modified polypyrrole (PPy) has been developed for the quantitative estimation of urea in aqueous solutions. The incorporation of urease (Urs) into a bipolymeric substrate consisting of PPy was performed by entrapment to the polymeric matrix, PPy acts as amperometric transducer in these biosensors. To increase the membrane conductivity, multi-walled carbon nanotubes (MWCNT) were added to the PPy solution. The entrapped MWCNT in PPy film and the bipolymer layers were prepared for construction of Pt/PPy/MWCNT/Urs. Two different configurations of working electrodes were evaluated to investigate the potential use of the modified membranes in biosensors. The evaluation of two different configurations of working electrodes suggested that the second configuration, which was composed of an electrode-mediator-(pyrrole and multi-walled carbon nanotube) structure and enzyme, is the best candidate for biosensor applications.

Keywords: urea biosensor, polypyrrole, multi-walled carbon nanotube, urease

Procedia PDF Downloads 300

Authors: I. K. Sharma

Abstract:

Over the years world over system are being developed by research labs continuously monitor under water parameters in the coastal waters of sea such as conductivity, salinity, pressure, temperature, chlorophyll and biological blooms at different levels of water column. The research institutions have developed profilers which are launched by ship connected through cable, glider type profilers following underwater trajectory, buoy any driven profilers, wire guided profilers etc. In all these years, the effect was to design autonomous profilers with no cable quality connection, simple operation and on line date transfer in terms accuracy, repeatability, reliability and consistency. Hence for the Ministry of Communication and Information Technology, India sponsored research project to National Institute of Oceanography, GOA, India to design and develop autonomous vertical profilers, it has taken system and AVP has been successfully developed and tested.

Keywords: oceanography, water column, autonomous profiler, buoyancy

Procedia PDF Downloads 383

Authors: Amal M. Alrayes, Hayat M. Ali

Abstract:

Since the beginning of distance education with the rapid evolution of technology, the social network plays a vital role in the educational process to enforce the interaction been the learners and teachers. There are many Web 2.0 technologies, services and tools designed for educational purposes. This research aims to investigate instructors’ acceptance towards web-based learning systems in higher educational institutes in Kingdom of Bahrain. Questionnaire is used to investigate the instructors’ usage of Web 2.0 and the factors affecting their acceptance. The results confirm that instructors had high accessibility to such technologies. However, patterns of use were complex. Whilst most expressed interest in using online technologies to support learning activities, learners seemed cautious about other values associated with web-based system, such as the shared construction of knowledge in a public format. The research concludes that there are main factors that affect instructors’ adoption which are security, performance expectation, perceived benefits, subjective norm, and perceived usefulness.

Keywords: Web 2.0, higher education, acceptance, students' perception

Procedia PDF Downloads 311

Authors: Amanda R. Teixeira, João H. S. Rego, Gabriel F. S. Brito, Fabricio M. Silva

Abstract:

The use of superplasticizer additives has provided several advances for the civil construction industry, enabling gains in the rheological behavior and mechanical properties of cementitious matrices. These compounds act at the solid-liquid interface of colloidal suspensions of cement pastes, preventing agglomeration of the particles. Although the use in the concrete industry is wide, the mechanisms of dispersion of concrete admixtures composed of polycarboxylate in cement with supplementary cementitious materials have ample opportunity to be investigated, providing the attainment of increasingly compatible and efficient cement-addition-additive systems. The cements used in the research are Portland Cement CPV and two cements Portland Cement Composite (CPIV) with calcined clay contents of 20% and 28% and three commercial additives based on polycarboxylate. The performance of the additives and obtaining the optimal content was determined by the Marsh Cone test and spread by Mini-Slump.

Keywords: calcined clay, composite cements, superplasticizer additives, polycarboxylate

Procedia PDF Downloads 80

Authors: Fateh Adhnouss, Husam El-Asfour, Kenneth McIsaac, AbdulMutalib Wahaishi, Idris El-Feghia

Abstract:

Conceptualization is an essential component of semantic ontology-based approaches. There have been several approaches that rely on extensional structure and extensional reduction structure in order to construct conceptualization. In this paper, several limitations are highlighted relating to their applicability to the construction of conceptualizations in dynamic and open environments. These limitations arise from a number of strong assumptions that do not apply to such environments. An intensional structure is strongly argued to be a natural and adequate modeling approach. This paper presents a conceptualization structure based on property relations and propositions theory (PRP) to the model ontology that is suitable for open environments. The model extends the First-Order Logic (FOL) notation and defines the formal representation that enables interoperability between software systems and supports semantic integration for software systems in open, dynamic environments.

Keywords: conceptualization, ontology, extensional structure, intensional structure

Procedia PDF Downloads 92

Authors: Geniece Mondé

Abstract:

This article examines how formerly incarcerated mothers deploy strategic comparisons to support their claims of moral self-worth. In depth interviews with 69 ex-offender mothers show that although women occupy a morally ambiguous space, they frame their roles as “good” mothers as independent of past illegal activity. In substantiating the “good” mother narrative women draw comparisons with two groups of women. Some respondents identify individuals perceived as morally disadvantaged and draw comparisons that illustrate their comparative strength in relation to mothers who fail to adequately meet the needs of their children. Women also compared themselves to morally advantaged mothers and expressed a desire to embody the ideals and values of women they viewed as superior mothers. Findings reveal that respondents’ use of strategic comparisons substantiates their framing of personal moral identity, as well as their goals for the future. The paper concludes by examining the theoretical implications of strategic comparisons for the study of morality and identity construction.

Keywords: Ex-Offender, Rehabilitation, Incarceration, Motherhood

Procedia PDF Downloads 119

Authors: Belinda Crissman

Abstract:

Serious mental disorder is greatly overrepresented in prisoners compared to the general community, with consequences for prison management, recidivism and the prisoners themselves. Incarcerated individuals with psychotic disorders experience insufficient detection and treatment and higher rates of suicide in custody. However direct evidence to explain the overrepresentation of individuals with psychosis in prisons is sparse. The current study aimed to use a life course criminology perspective to answer two key questions: 1) What is the temporal relationship between psychosis and offending (does first mental health contact precede first recorded offence, or does the offending precede the mental health diagnosis)? 2) Are there key temporal points or system contacts prior to incarceration that could be identified as opportunities for early intervention? Data from the innovative Queensland Linkage project was used to link individuals with their corrections, health and relevant social service systems to answer these questions.

Keywords: mental disorder, crime, life course criminology, prevention

Procedia PDF Downloads 113

Authors: Clarissa D. M. O. Guimaraes, Mariza C. M. Fernandes, Francisco R. V. Diaz, Juliana R. Souza

Abstract:

The use of mineral fillers in the preparation of organic matrix composites can be an efficient alternative in minimizing the environmental damage generated in passive mineral beneficiation processes. In addition, it may represent a new material option for wind, construction, and aeronautical industries, for example. In this sense, epoxy resin composites with Tailings of Scheelite (TS) were developed. The composites were manufactured with 5%, 10% and 20% of TS in volume percentage, homogenized by mechanical mixing and molded in a silicon mold. In order to make the tribological evaluation, pin on disk tests were performed to analyze coefficient of friction and wear. The wear mechanisms were identified by SEM (scanning electron microscope) images. The coefficient of friction had a tendency to decrease with increasing amount of filler. The wear tends to increase with increasing amount of filler, although it exhibits a similar wear behavior. The results suggest characteristics that are potential used in many tribological applications.

Keywords: composites, mineral filler, tailings of scheelite, tribology

Procedia PDF Downloads 149

Authors: Ece Kaya

Abstract:

Urban waterfront re-development is a well-established phenomenon internationally since 1960s. In cities throughout the world, old industrial waterfront land is being redeveloped into luxury housing, offices, tourist attractions, cultural amenities and shopping centres. These developments are intended to attract high-income residents, tourists and investors to the city. As urban waterfronts are iconic places for the cities and catalyst for further development. They are often referred as flagship project. In Sydney, the re-development of industrial waterfront has been exposed since 1980s with Darling Harbour Project. Darling Harbour waterfront used to be the main arrival and landing place for commercial and industrial shipping until 1970s. Its urban development has continued since the establishment of the city. It was developed as a major industrial and goods-handling precinct in 1812. This use was continued by the mid-1970s. After becoming a redundant industrial waterfront, the area was ripe for re-development in 1984. Darling Harbour is now one of the world’s fascinating waterfront leisure and entertainment destinations and its transformation has been considered as a success story. It is a contradictory statement for this paper. Data collection was carried out using an extensive archival document analysis. The data was obtained from Australian Institute of Architects, City of Sydney Council Archive, Parramatta Heritage Office, Historic Houses Trust, National Trust, and University of Sydney libraries, State Archive, State Library and Sydney Harbour Foreshore Authority Archives. Public documents, primarily newspaper articles and design plans, were analysed to identify possible differences in motives and to determine the process of implementation of the waterfront redevelopments. It was also important to obtain historical photographs and descriptions to understand how the waterfront had been altered. Sites maps in different time periods have been identified to understand what kind of changes happened on the urban landscape and how the developments affected areas. Newspaper articles and editorials have been examined in order to discover what aspects of the projects reflected the history and heritage. The thematic analysis of the archival data helped determine Darling Harbour is a historically important place as it had represented a focal point for Sydney's industrial growth and the cradle of industrial development in European Australia. It has been found that the development area was designated in order to be transformed to a place for tourist, education, recreational, entertainment, cultural and commercial activities and as a result little evidence remained of its industrial past. This paper aims to discuss the industrial significance of Darling Harbour and to explain the changes on its industrial landscape. What is absent now is the layer of its history that creates the layers of meaning to the place so its historic industrial identity is effectively lost.

Keywords: historical significance, industrial heritage, industrial waterfront, re-development

Procedia PDF Downloads 286

Authors: Harendra Singh, Rajesh Pandey

Abstract:

The paper presents a numerical method based on operational matrix of integration and Ryleigh method for the solution of a class of non-linear fractional variational problems (NLFVPs). Chebyshev first kind polynomials are used for the construction of operational matrix. Using operational matrix and Ryleigh method the NLFVP is converted into a system of non-linear algebraic equations, and solving these equations we obtained approximate solution for NLFVPs. Convergence analysis of the proposed method is provided. Numerical experiment is done to show the applicability of the proposed numerical method. The obtained numerical results are compared with exact solution and solution obtained from Chebyshev third kind. Further the results are shown graphically for different fractional order involved in the problems.

Keywords: non-linear fractional variational problems, Rayleigh-Ritz method, convergence analysis, error analysis

Procedia PDF Downloads 278

Authors: Faraz Nikpour Arani, Shahin Haghi Navand

Abstract:

After Two years of operation, the “Nahj Al Balaghe” riverside park, redesigning research was ordered by second region of Tehran municipality, the goal was to construct the first cultural tourism center in city of Tehran. After Pathological and analytical studies of existing situation, that made by field work research’s and interviews, the main problems was identified as lack of thematic design and some physical problems that reduced the activity and livability ratio of the park. The main approach of this project was thematic physical redesign and redefinition of activities in order to the “Nahj Al Balaghe’s” ideas, cultural days in “shamsi calendar”, the “7 artistic dimensions” and “four classical elements”. This paper is the abstraction of a full research that was done by writers.

Keywords: thematic redesign, Nah Al Balaghe riverside park, cultural tourism center, Tehran

Procedia PDF Downloads 622

Authors: Christos Stamopoulos

Abstract:

Nowadays, the technological evolution has brought changes and new requirements not only on human’s life but also on the environment in which they live. Cities have begun to be organized in new ways which comply with contemporary living standards. The aim of this paper was to present the characteristics and to introduce good construction strategies of smart cities around the world. Also, a case study of the city of Kalampaka and its residents was surveyed. More specifically, residents’ knowledge about smart cities and their opinion for future progress was examined. Statistical analysis showed that residents’ knowledge about smart cities was fairly good (48% knew the phrase 'smart city'). However, respondents believe that the appearance of the city of Kalampaka needs improvement in many areas (the 75% are disappointed with the current appearance of the city). Furthermore, regression analysis showed that the value of the environmental sustainability is greatly influenced by the energy saving, as well as, innovation has an impact on the level of quality of life, while older people seem satisfied with administration’s efforts for development.

Keywords: development, economy, environment, governance, quality of life, smart city

Procedia PDF Downloads 323

Authors: Rezki Akkouche

Abstract:

This work exposes metal tanks in general and floating roofs in particular by listing the codes and standards which study this kind of structure. Initial research discusses the types of tanks, how they are designed, and the disadvantages and advantages that each type has. Then, in-depth research was carried out carefully in order to popularize the floating roof tank and the principles of its design and operation while defining the different types of this kind of roof, how and what they are designed, naming the main installation accessories for these roofs and the dangers that a malfunction of these accessories would cause, also exposing the problems likely to be encountered on these roofs and the considerable and important advantages that floating roof tanks bring. A simplification of the two API 650 and Eurocode 3 regulations - Tanks part - has been made by explaining and mentioning the design rules and laws of this type of structure. Thus a comparison of the two regulations is accomplished by exemplifying this with a study of an actual project.

Keywords: tanks of metal, floating roof, performance, comparative analysis

Procedia PDF Downloads 113

Authors: Daianne Fernandes Diogenes

Abstract:

Railway ballast aggregates’ shape properties and size distribution can be directly affected by several factors, such as traffic, fouling, and maintenance processes, which cause breakage and wearing, leading to the fine particles’ accumulation through the ballast layer. This research aims to analyze the influence of traffic, tamping process, and sleepers’ stiffness on aggregates' shape and mechanical properties, by using traditional and digital image processing (DIP) techniques and cyclic tests, like resilient modulus (RM) and permanent deformation (PD). Aggregates were collected in different phases of the railway service life: (i) right after the crushing process; (ii) after construction, for the aggregates positioned below the sleepers and (iii) after 5 years of operation. An increase in the percentage of cubic particles was observed for the materials (ii) and (iii), providing a better interlocking, increasing stiffness and reducing axial deformation after 5 years of service, when compared to the initial conditions.

Keywords: digital image processing, mechanical behavior, railway ballast, shape properties

Procedia PDF Downloads 104

Authors: Chen Xi, Kuan Sinman, LI Haofeng, Huang Hongming, Zeng Chengyu, Tong Zhiyuan

Abstract:

Stray animals are on the rise in mainland China's cities. There are legal reasons for this, namely the lack of protection for domestic pets in mainland China, where only wildlife protection laws exist. At a social level, the ease with which families adopt pets and the lack of a social view of animal nature has led to the frequent abandonment and loss of stray animals. If left unmanaged, conflicts between humans and stray animals can also increase. This project provides an inexpensive and widely applicable management tool for urban management by collecting videos and pictures of stray animals captured by surveillance or transmitted by humans and using artificial intelligence technology (mainly using YOLOv5 recognition technology) and recording and managing them in a database.

Keywords: urban planning, urban governance, artificial intelligence, convolutional neural network

Procedia PDF Downloads 84

Authors: Hang Tran, Victor Brial, Luca Sorelli, Claudiane Ouellet-Plamondon, David Conciatori, Laurent Birry

Abstract:

Spend pot lining (SPL) is a by-product generated from primary aluminum production. SPL consists of two parts, the first cut is rich in carbonaceous materials, and the second cut is rich in aluminum and silicon oxides. After treating by the hydrometallurgical Low Caustic Leaching and Liming process, the refractory part of SPL becomes an inert material, called LCLL ash in this project. LCLL ash was calcined at different temperatures (800 and 1000°C) and Calcined LCLL ash ground as fines of cement and replacement a part of cement in concrete production. The effect of LCLL ash on the chemical properties, mechanical properties and fresh behavior of concrete was evaluated by isothermal calorimetry, compressive test, and slump test. These results were compared to the reference mixture.

Keywords: spend pot lining, concrete, cement, compressive strength, calorimetry

Procedia PDF Downloads 199

Authors: Mathula Thangarajh

Abstract:

Duchenne muscular dystrophy (DMD) is a severe form of X-linked muscular dystrophy caused by mutations in the dystrophin gene resulting in progressive skeletal muscle weakness. Boys with DMD also have significant cognitive disabilities. The intelligence quotient of boys with DMD, compared to peers, is approximately one standard deviation below average. Detailed neuropsychological testing has demonstrated that boys with DMD have a global developmental impairment, with verbal memory and visuospatial skills most significantly affected. Furthermore, the total brain volume and gray matter volume are lower in children with DMD compared to age-matched controls. These results are suggestive of a significant structural and functional compromise to the developing brain as a result of absent dystrophin protein expression. There is also some genetic evidence to suggest that mutations in the 3’ end of the DMD gene are associated with more severe neurocognitive problems. Our working hypothesis is that (i) boys with DMD do not make gains in neurodevelopmental skills compared to typically developing children and (ii) women carriers of DMD mutations may have subclinical cognitive deficits. We also hypothesize that there may be an intergenerational vulnerability of cognition, with boys of DMD-carrier mothers being more affected cognitively than boys of non-DMD-carrier mothers. The objectives of this study are: 1. Assess the neurodevelopment in boys with DMD at 4-time points and perform baseline neuroradiological assessment, 2. Assess cognition in biological mothers of DMD participants at baseline, 3. Assess possible correlation between DMD mutation and cognitive measures. This study also explores functional brain abnormalities in people with DMD by exploring how regional and global connectivity of the brain underlies executive function deficits in DMD. Such research can contribute to a better holistic understanding of the cognition alterations due to DMD and could potentially allow clinicians to create better-tailored treatment plans for the DMD population. There are four study visits for each participant (baseline, 2-4 weeks, 1 year, 18 months). At each visit, the participant completes the NIH Toolbox Cognition Battery, a validated psychometric measure that is recommended by NIH Common Data Elements for use in DMD. Visits 1, 3, and 4 also involve the administration of the BRIEF-2, ABAS-3, PROMIS/NeuroQoL, PedsQL Neuromuscular module 3.0, Draw a Clock Test, and an optional fMRI scan with the N-back matching task. We expect to enroll 52 children with DMD, 52 mothers of children with DMD, and 30 healthy control boys. This study began in 2020 during the height of the COVID-19 pandemic. Due to this, there were subsequent delays in recruitment because of travel restrictions. However, we have persevered and continued to recruit new participants for the study. We partnered with the Muscular Dystrophy Association (MDA) and helped advertise the study to interested families. Since then, we have had families from across the country contact us about their interest in the study. We plan to continue to enroll a diverse population of DMD participants to contribute toward a better understanding of Duchenne Muscular Dystrophy.

Keywords: neurology, Duchenne muscular dystrophy, muscular dystrophy, cognition, neurodevelopment, x-linked disorder, DMD, DMD gene

Procedia PDF Downloads 86

Authors: Thong Lantharthong, Nattchote Rugthaicharoencheep, Att Phayomhom

Abstract:

This paper presents the electrical effect of two neighboring distribution substation during the construction phase. The size of auxiliary grounding grid have an effect on entire grounding system. The bigger the size of auxiliary grounding grid, the lower the GPR and maximum touch voltage, with the exception that when the two grids are unconnected, i.e. the bigger the size of auxiliary grounding grid, the higher the maximum step voltage. The results in this paper could be served as design guideline of grounding system, and perhaps remedy of some troublesome grounding grids in power distribution’s system. Modeling and simulation is carried out on the Current Distribution Electromagnetic interference Grounding and Soil structure (CDEGS) program. The simulation results exhibit the design and analysis of power system grounding and perhaps could be set as a standard in grounding system design and modification in distribution substations.

Keywords: grounding system, touch voltage, step voltage, safety criteria

Procedia PDF Downloads 436

Authors: Saurabh Sharma

Abstract:

Introduction: The case study deals with the ground stabilisation of Nabi Karim Metro Station in Delhi, India, wherein an extremely complex geology was encountered while excavating the tunnelling shaft for launching Tunnel Boring Machine. The borelog investigation and the Seismic Refraction Technique (SRT) indicated towards the presence of an extremely hard rocky mass from a depth of 3-4 m itself, and accordingly, the Geotechnical Interpretation Report (GIR) concluded the presence of Grade-IV rock from 3m onwards and presence of Grade-III and better rock from 5-6m onwards. Accordingly, it was planned to retain the ground by providing secant piles all around the launching shaft and then excavating the shaft vertically after leaving a berm of 1.5m to prevent secant piles from getting exposed. To retain the side slopes, rock bolting with shotcreting and wire meshing were proposed, which is a normal practice in such strata. However, with the increase in depth of excavation, the rock quality kept on decreasing at an unexpected and surprising pace, with the Grade-III rock mass at 5-6 m converting to conglomerate formation at the depth of 15m. This worsening of geology from high grade rock to slushy conglomerate formation can never be predicted and came as a surprise to even the best geotechnical engineers. Since the excavation had already been cut down vertically to manage the shaft size, the execution was continued with enhanced cautions to stabilise the side slopes. But, when the shaft work was about to finish, a collapse was encountered on one side of the excavation shaft. This collapse was unexpected and surprising since all measures to stabilise the side slopes had been taken after face mapping, and the grid size, diameter, and depth of the rockbolts had already been readjusted to accommodate rock fractures. The above scenario was baffling even to the best geologists and geotechnical engineers, and it was decided that any further slope stabilisation scheme shall have to be designed in such a way to ensure safe completion of works. Accordingly, following revisions to excavation scheme were made: The excavation would be carried while maintaining a slope based on type of soil/rock. The rock bolt type was changed from SN rockbolts to Self Drilling type anchor. The grid size of the bolts changed on real time assessment. the excavation carried out by implementing a ‘Bench Release Approach’. Aggressive Real Time Instrumentation Scheme. Discussion: The above case Study again asserts vitality of correct interpretation of the geological strata and the need of real time revisions of the construction schemes based on the actual site data. The excavation is successfully being done with the above revised scheme, and further details of the Revised Slope Stabilisation Scheme, Instrumentation Schemes, Monitoring results, along with the actual site photographs, shall form the part of the final Paper.

Keywords: unconfined compressive strength (ucs), rock mass rating (rmr), rock bolts, self drilling anchors, face mapping of rock, secant pile, shotcrete

Procedia PDF Downloads 56

Authors: K. Bose

Abstract:

India is one of the largest democracies in the global south, which demonstrates the highest social enterprise activities in the subcontinent. Although there has been a meteoric rise in social enterprise activities, it is not a new phenomenon, as it dates back to Vinoba Bhave's Land Gift movement in 1950. India also has a rich history of a welfare mix where non-governmental organisations played a significant role in the public welfare provision. Lately, the government’s impetus on entrepreneurship has contributed to a burgeoning social enterprise sector in the country; however, there is a lack in understanding of how social enterprises are constructed in India. Social entrepreneurship as practice has been conceptualised as a multi-dimensional concept, which is predominantly explained through the characteristics of a social entrepreneur. Social enterprise organisation, which is a component of social entrepreneurship practice are also classified through the role of the social entrepreneur; thus making social entrepreneur a vital unit shaping organisation and practice. Hence, individual identity of the social entrepreneur acts as a steering agent for defining organisation and practice. Individual identity does not operate in a vacuum and different isomorphic pressures (resource-rich actors/institutions) leads to negotiation in these identities. Dey and Teasdale's work investigated this identity work of non-profit practitioners within the practice of social enterprises in England. Furthermore, the construction of social enterprises is predominantly understood through two approaches i.e. an institutional logic perspective emerging from Europe and process and outcome perspective derived from the United States. These two approaches explain social enterprise as an inevitable institutional outcome in a linear and simplistic manner. Such linear institutional transition is inferred from structural policy reforms and austerity measures adopted by the government, which led to heightened competition for funds in the non-profit sector. These political and economic challenges were specific to the global north, which is different from transitions experienced in the global south, thus further investigation would help understand social enterprise activities as a contextual phenomenon. There is a growing interest in understanding the role of the context within the entrepreneurship literature, additionally, there is growing recognition in entrepreneurship research that economic behaviour is realised far better within its historical, temporal, institutional, spatial and social context, as these contexts provide boundaries to individuals in terms of opportunities and actions. Social enterprise phenomenon too is realised as contextual phenomenon though it differs from traditional entrepreneurship in terms of its dual mission (social and economic), however, the understanding of the role of context in social entrepreneurship has been limited. Hence, this work in progress study integrates identity work of social entrepreneur and the role of context. It investigates the identities of social entrepreneur and its negotiation within its context. Further, how this negotiated identity transcends into organisational practice in turn shaping how social enterprises are constructed in a specific region. The study employs a qualitative inquiry of semi-structured interviews and ethnographic institutionalism. Interviews were analysed using critical discourse analysis and the preliminary outcomes are currently a work in progress.

Keywords: context, Dey and Teasdale, identity, social entrepreneurs, social enterprise, social entrepreneurship

Procedia PDF Downloads 158

Authors: Fawehinmi Olabisi Alaba, O. R. Adeniyi

Abstract:

Farming households faces lots of disaster which contribute to endemic poverty. Anticipated increases in extreme weather events will exacerbate this. Primary data was administered to farming household using multi-stage random sampling technique. The result of the analysis shows that majority of the respondents (69.9%) are male, have mean household size, years of formal education and age of 5±1.14, 6±3.41, and 51.06±10.43 respectively. The major (48.9%) type of disaster experienced is flooding. Major coping mechanism adopted is sourcing for support from family and friends. Age, education, experience, access to extension agent, and mitigation control method contribute significantly to vulnerability to disaster. The major adaptation method (62.3%) is construction of drainage. The study revealed that the coping mechanisms employed may become less effective as increasingly fragile livelihood systems struggle to withstand disaster shocks. Thus there is need for training of the farmers on measures to adapt to mitigate the shock from disasters.

Keywords: adaptation, disasters, flooding, vulnerability

Procedia PDF Downloads 244

Authors: Antarjeeta Nayak, Jalandhar Pradhan, Ramakrishna Biswal

Abstract:

Poverty is a complex phenomenon influenced by a large number of factors and which can be studied from many different perspectives. Most of the poverty assessments can be divided into three broad categories- construction of poverty profile (who the poor are), causes of poverty (why people are poor) and poverty alleviation strategies (what to do about poverty). In this regard, we need to know more about poverty, the factors that drive it and those that maintain it. Specifically, how people perceive and experience poverty will generate a body of knowledge that would enable government and poverty alleviation agencies to better target their interventions and understand the stigma associated with poverty. In the Indian context, the perceptions of the causes of poverty are particularly relevant because of the persistent higher percent of people below poverty line and wider economic-social inequalities despite the continuing decline of poverty in the present times. In this study we investigated the perceived attributions for poverty among youths (University students) in India. A questionnaire having 35 questions was administered to a sample of 200 University students (n=200). Findings showed that Indian youth were more inclined to attribute poverty to Structural factors; supporting system-blame hypothesis.

Keywords: poverty, perception of the causes of poverty, Indian youth, social sciences and humanities

Procedia PDF Downloads 402