Search results for: eliminate redundant civil work

Authors: Tapas Kumar Sinha, Joseph Mathew

Abstract:

At the moment earth is in grave danger due to threats of global warming. The temperature of the earth has risen by almost 20C. Glaciers in the Arctic have started to melt. It would be foolhardy to think that this is a small effect and in time it would go away. Global warming is caused by a number of factors. However, one sure and simple way to totally eliminate this problem is to put programmable shields in space. Just as an umbrella blocks sunlight, a programmable shield in space will block sun rays from reaching the earth as in a solar eclipse and cause cooling in the penumbral region just as it happens during an eclipse.

Keywords: glaciers, green house, global warming space, satellites

Procedia PDF Downloads 562

Authors: Boukhadia Karima

Abstract:

The fluid mechanics is the study of fluid motion laws and their interaction with solid bodies, this project leads to illustrate this interaction with depth studies and approved by experiments on the wind tunnel TE44, ensuring the efficiency, accuracy and reliability of these tests on a NACA0015 profile. A symmetric NACA0015 was placed in a subsonic wind tunnel, and measurements were made of the pressure on the upper and lower surface of the wing and of the velocity across the vortex trailing downstream from the tip of the wing. The aim of this work is to investigate experimentally the scattered pressure profile in a free airflow and the aerodynamic forces acting on this profile. The addition of around-lateral edge to the wing tip was found to eliminate the secondary vortex near the wing tip, but had little effect on the downstream characteristics of the trailing vortex. The increase in wing lift near the tip because of the presence of the trailing vortex was evident in the surface pressure, but was not captured by circulation-box measurements. The circumferential velocity within the vortex was found to reach free-stream values and produce core rotational speeds. Near the wing, the trailing vortex is asymmetric and contains definite zones where the stream wise velocity both exceeds and falls behind the free-stream value. When referenced to the free stream velocity, the maximum vertical velocity of the vortex is directly dependent on α and is independent of Re. A numerical study was conducted through a CFD code called FLUENT 6.0, and the results are compared with experimental.

Keywords: CFD code, NACA Profile, detachment, angle of incidence, wind tunnel

Procedia PDF Downloads 386

Authors: Samina Khalid, Shamila Nasreen

Abstract:

Dimensionality reduction as a preprocessing step to machine learning is effective in removing irrelevant and redundant data, increasing learning accuracy, and improving result comprehensibility. However, the recent increase of dimensionality of data poses a severe challenge to many existing feature selection and feature extraction methods with respect to efficiency and effectiveness. In the field of machine learning and pattern recognition, dimensionality reduction is important area, where many approaches have been proposed. In this paper, some widely used feature selection and feature extraction techniques have analyzed with the purpose of how effectively these techniques can be used to achieve high performance of learning algorithms that ultimately improves predictive accuracy of classifier. An endeavor to analyze dimensionality reduction techniques briefly with the purpose to investigate strengths and weaknesses of some widely used dimensionality reduction methods is presented.

Keywords: age related macular degeneration, feature selection feature subset selection feature extraction/transformation, FSA’s, relief, correlation based method, PCA, ICA

Procedia PDF Downloads 460

Authors: Izzati Nabiyla Risfa

Abstract:

The role of civil society has become an important issue in national and international level nowadays. Government all over the world started to realize that the involvement of civil society can boost up public services and better policy making. Global Policy Forum stated that there are five good reasons for civil society to be engaged in global governance; (1) to conferring legitimacy on policy decisions; (2) to increasing the pool of policy ideas; (3) to support less powerful governments; (4) countering a lack of political will; and (5) helping states to put nationalism aside. Indonesia also keeps up with this good trend. In November 2011, Indonesian Government set up LAPOR! (means “to report” in Indonesian), an online portal for complaints about public services, which is accessible through its website lapor.ukp.go.id. LAPOR! also accessible through social media (Twitter, Facebook) and text message. This program is an initiative from the government to provide an integrated and accessible portal for the Indonesian public to submit complaints and inquiries as a means of enhancing public participation in national development programs. LAPOR! aims to catalyze public participation as well as to have a more coordinated national complaint handling mechanism. The goal of this program is to increase the role of civil society in order to develop better public services. Thus, LAPOR! works in a simplest way possible. Public can submit any complaints or report their problem concerning development programs and public services simply through the website, short message services to 1708 and mobile applications for BlackBerry and Android. LAPOR! will then transfer every validated input to relevant institutions to be featured and responded on the website. LAPOR! is now integrated with 81 Ministries, 5 local government, and 44 State Owned Enterprise. Public can also give comments, likes or share them through Facebook and Twitter to have a discussion and to ensure the completeness of the reports. LAPOR! has unexpectedly contributed to various successful cases concerning public services. So far the portal has over 280,704 registered users, receiving an average of 1,000 reports every day. Government's response rate increase time to time, with 81% of complaints and inquiries have been solved or are being investigated. This paper will examine the effectiveness of LAPOR! as a tools to increase the role of civil society in order to develop better public services in Indonesia. Beside their promising story, there still are various difficulties that need to be solved. With qualitative approach as methodology for this research, writers will also explore potential improvement of LAPOR! so it can perform effectively as a leading national complaint handling system in Indonesia.

Keywords: civil society, government, Indonesia, public services

Procedia PDF Downloads 455

Authors: Idette Sheirina Biyo, Rhodora Lynn C. Lintag

Abstract:

This paper explores how the work-life balance of selected working single mothers situated in a coastal community is affecting their well-being. Working single mothers carry the responsibility of earning for their family while simultaneously exercising their motherhood. This study utilized a purposeful qualitative research through semi-structured interviews among ten working single mothers living in the coastal community of La Huerta, Parañaque in order to identify the following: a) experiences of the working single mothers, b) problems usually encountered, and c) how these problems are affecting their well-being. Dorothy Smith’s Feminist Standpoint theory is used as a theoretical lens in order to explain their work-life balance. Results have shown that despite their dual roles as the main income earners and heads of the households, they are not neglecting to care for their well-being. They consider getting sufficient rest, eating well, and going to church as forms of caring for their well-being. Other factors that affect their work-life balance include living arrangements, work hours, type of work, and income.

Keywords: coastal community, well-being, work-life balance, Working single mother

Procedia PDF Downloads 172

Authors: Baptiste Brodard

Abstract:

In Switzerland, as well as in other European countries, specific social issues related to Muslims have recently emerged in public debates. In addition to the question of terrorism and radicalization, Muslim migrant populations are highly affected by social problems such as crime, poverty, marginalization, and overrepresentation in prisons. This situation has drawn the state’s attention to the need for implementing new responses to the challenges of religious extremism, crime, and social exclusion particularly involving Muslims. While local authorities have begun to implement trainings and projects to tackle these new social issues, Muslim grassroots associations have developed some initiatives to address the needs of the population, mainly focusing on problems related to Islam and Muslims but also addressing the rest of the population. Finally, some local authorities have acknowledged the need for these alternative initiatives as well as their positive contributions to society. The study is based on a Ph.D. research grounded on a case study of three Islamic networks in Switzerland, including various local organizations tackling social exclusion and religious radicalization through innovative grassroots projects. Using an ethnographic approach, it highlights, on the one hand, the specificities of such organizations by exploring the role of Islamic norms within the social work practices. On the other hand, it focuses on the inclusion of such faith-based projects within the mainstream society, observing the relationships between Islamic organisations and both the state and other civil society organizations. Finally, the research study aims to identify some innovative ways and trends of social work involving the inclusion of community key actors within the process. Results showed similar trends with Islamic social work developed in other European countries such as France and the United Kingdom, but also indicate a range of specificities linked to the Swiss socio-political context, which shapes the involvement of religious actors in different ways. By exploring faith-based commitment to addressing concrete social issues, the study finally contributes to shedding light on the link between Islam, social work and activism within the European context.

Keywords: exclusion, Islam, Muslims, social work, Switzerland

Procedia PDF Downloads 100

Authors: Goh Mingyuan Asher, Nurul Fadiah Johari, Neo Yu Wei, Kim Aryung, Ho Kong Chong, Irene Y. H. N. G.

Abstract:

The COVID-19 pandemic represents an externally induced force as they face a combination of reduced work, dismissal, and job change for young precarious workers. The paper drew insights from two interview waves of the in-work poverty study in Singapore which were conducted a year apart. By analysing respondents’ job histories before and at the start of the pandemic as well as their job experiences over the two waves of interviews, the study found the presence of what scholars describe as trap and stepping stone trajectories. Trap trajectories refer to how the nature of precarious employment leads respondents to be in dead-end jobs with no room for progression while stepping stone trajectories refer to how poor work provides opportunities for the accumulation of work experiences. We also look at how structure, agency and biographical factors affect job trajectories and discuss the impacts of COVID-19 on work experiences and the implications of the bifurcation of trajectory outcomes on poverty and inequality among the young working poor in Singapore.

Keywords: working poor, precarity, young workers, COVID-19, work trajectories

Procedia PDF Downloads 79

Authors: Ruilin Zhu, Katarzyna Olcoń, Rose M. Pulliam, Dorie J. Gilbert

Abstract:

Cultural humility is increasingly important in social work literature, given its emphasis on mitigating power imbalances in helping relationships, particularly across cultural differences. Consequently, there is a need to understand whether and how cultural humility can be taught in social work education. Relying on ethnographic observations and reflective journals from a cultural immersion program, this study identified the learning process required to develop cultural humility: confusion and discomfort, re-moulding, and humility in action.

Keywords: social work education, cultural humility, transformative learning theory, study abroad, ethnographic observations

Procedia PDF Downloads 132

Authors: Jacinta Ifeoma Obidile

Abstract:

Teachers (vocational and technical educators inclusive) use Information and Communications Technology (ICT) for tasks outside of their normal working hours. This expansion of work duties to non-work time challenges their work-life balance. However, there has been inconsistency in the results on how these relationships correlate. This, therefore, calls for further research studies to examine the moderating mechanisms of such relationships. The present study, therefore, ascertained how vocational and technical educators’ technology acceptance relates to their work-related ICT use beyond their working hours and work-life balance, as well as how their integration affects these relationships. The population of the study comprised 320 Vocational and Technical Educators from the Southeast geopolitical zone of Nigeria. Data were collected from the respondents using the structured questionnaire. The questionnaire was validated by three experts. The reliability of the study was conducted using 20 vocational and technical educators from the South who were not part of the population. The overall reliability coefficient of 0.81 was established using Cronbach’s alpha method. The data collected was analyzed using Structural equation modeling. Findings, among others, revealed that vocational and technical educators’ work-life balance was mediated by increased digital learning environment use after work hours, although reduced by social influence.

Keywords: vocational and technical educators, digital learning environment, working hours, work-life balance, integration preference

Procedia PDF Downloads 24

Authors: Zurong Liang

Abstract:

Chinese social work has experienced a sharp rise in staff turnover. Work-family conflict is a key risk factor for employees’ turnover intention. While the relationship between work-family conflict and turnover intention has been widely documented, little is known about its mediating and moderating mechanisms, especially among social workers in China. This study explored the mediating role of job-based and collective psychological ownership and the moderating role of person-organization value congruence. The study drew on data from the China Social Work Longitudinal Study 2019, a nationally representative sample of 1,421 Chinese social workers (79.73% female; mean age = 28.9 years old). We performed a moderated mediation analysis combining a simple slope test and the Johnson-Neyman technique. Both job-based psychological ownership and collective psychological ownership were found to mediate the association between work-family conflict and turnover intention. Person-organization value congruence moderated the indirect relationship between work-family conflict and turnover intention via collective psychological ownership. This study enhances understanding of the impact of the psychological mechanisms of work-family conflict on Chinese social workers’ turnover intention. Specific strategies should be adopted to establish a work environment that supports psychological ownership, enhances social workers’ identification with and attachment to their organizations, and thus reduces their turnover intention.

Keywords: turnover, work-family conflict, ownership, social worker, China

Procedia PDF Downloads 27

Authors: Natalia Khvorostianov, Nelly Elias

Abstract:

The present study seeks to analyze representation of social work in immigrant media, focusing on the case of online newspapers established by immigrants from the Former Soviet Union (FSU) in Israel. This immigrant population is particularly interesting because social work did not exist as a profession practiced in the USSR and hence most FSU immigrants arrive in Israel without a basic knowledge of the essence of social work, the services it provides and the logic behind its treatment methods. The sample of 37 items was built through a Google search of the Russian online newspapers and portals originated in Israel by using keywords such as “social worker,” “social work services” and the like. All items were analyzed by using qualitative content analysis. Principal analytical categories used for the analysis were: Assessment of social work services (negative, positive, neutral); social workers’ professionalism and effectiveness; goals and motives underlying their activity; cross-cultural contact with immigrants and methods used in working with immigrants. On this basis, four dominant images used to portray Israeli social work services and social workers were identified: Lack of professionalism, cultural gaps between FSU immigrants and Israeli social workers, repressive character of social work services and social workers’ involvement in corruption and crime.

Keywords: FSU immigrants, immigrant media, media images, social workers

Procedia PDF Downloads 337

Authors: Houmame Benbouali

Abstract:

This paper introduces the design, analysis, tests and application of a new isolation system used in irregular structure, also briefly introduces the recent research, and development on seismic isolation of civil buildings in China. A very large platform (2 stories RC frame) with plane size 1500m wide and 2000m long was built to cover the city railway communication hub area. About 50 isolation house buildings (9 stories RC frame) with 480,000 M2 were built on the top floor of platform. A new advanced isolation system named Storied-Isolation was used to ensure the seismic safety for this irregular structure with the largest isolation house building area in the world. This new isolation system has been used widely in China. There are over 400 buildings with seismic isolation have been built in China until 2003. This paper will introduce the recent research, and development on seismic isolation of civil buildings in China, including the tendency of application on seismic isolation, different isolation systems, different design level being used, design codes, application status and examples of application. Also the paper makes discussion of some problems on the future development of seismic isolation in China.

Keywords: civil buildings, floor, irregular structure, seismic isolation

Procedia PDF Downloads 297

Authors: Rajaa Filali, Mohamed Bouhdadi

Abstract:

This paper presents an incremental formal development of the Wireless Transaction Protocol (WTP) in Event-B. WTP is part of the Wireless Application Protocol (WAP) architectures and provides a reliable request-response service. To model and verify the protocol, we use the formal technique Event-B which provides an accessible and rigorous development method. This interaction between modelling and proving reduces the complexity and helps to eliminate misunderstandings, inconsistencies, and specification gaps. As result, verification of WTP allows us to find some deficiencies in the current specification.

Keywords: event-B, wireless transaction protocol, proof obligation, refinement, Rodin, ProB

Procedia PDF Downloads 292

Authors: Jin Woong Lee, Kyuman Cho, Taehoon Kim

Abstract:

The application of constructability is increasingly required not only in the construction phase but also in the whole project stage. In particular, the proper application of construction experience and knowledge during the design phase enables the minimization of inefficiencies such as design changes and improvements in constructability during the construction phase. In order to apply knowledge effectively, engineering technology efforts should be implemented with design progress. Among many engineering technologies, engineering for temporary works, including facilities, equipment, and other related construction methods, is important to improve constructability. Therefore, as basic research, this study investigates the applicability of temporary work engineering during the design phase in the building construction industry. As a result, application of temporary work engineering has a greater impact on construction cost reduction and constructability improvement. In contrast to the existing design-bid-build method, the turn-key and CM (construct management) procurement methods currently being implemented in Korea are expected to have a significant impact on the direction of temporary work engineering. To introduce temporary work engineering, expert/professional organization training is first required, and a lack of client awareness should be preferentially improved. The results of this study are expected to be useful as reference material for the development of more effective temporary work engineering tasks and work processes in the future.

Keywords: Temporary Work Engineering, Design Phase, Constructability, Building Construction

Procedia PDF Downloads 360

Authors: Kenneth O. Otasowie, Matthew Ikuabe, Clinton Aigbavboa, Ayodeji Oke

Abstract:

Subcontracting has become a fundamental feature in the construction industry, particularly as most projects in South Africa (SA) are executed by subcontractors. However, the sector in SA contributes to the high level of occupational hazards and injuries recorded, despite Health and Safety (H&S) regulations being enforced in the industry. Hence, this study aims to evaluate the barriers to health and safety practices by subcontractors in SA Construction Industry. A survey design was adopted. A total number of one hundred and forty-four (144) questionnaires were administered to quantity surveyors, construction managers, construction project managers, project managers, architects, and civil and structural engineers, who are owners or work in small and medium enterprises in Guateng Province, SA and eighty-three (83) were returned and found suitable for analysis. Collected data were analysed using percentage, mean item score, standard deviation, and one-sample t-test. The findings show that lack of skilled workers, lack of safety training, and insufficient safety awareness are the most significant barriers to health and safety practices in SA Construction Industry. Therefore, the study recommends the improvement in skills of staff and adequate training for the safe execution of work be provided to all employees and supervisors in these subcontracting firms. These will mitigate the rate of accident occurrence on construction sites.

Keywords: barriers, health and safety, subcontractors, South Africa

Procedia PDF Downloads 76

Authors: V. Jaime Contreras, S. Iliana Nunez, S. Mario Sanchez

Abstract:

Inside a manufacturing facility, we can find innumerable automatic and manual operations, all of which are relevant to the production process. Some of these processes add more value to the products more than others. Manual operations tend to add value to the product since they can be found in the final assembly area o final operations of the process. In this areas, where a mistake or accident can increase the cost of waste exponentially. To reduce or mitigate these costly mistakes, one approach is to rely on automation to eliminate the operator from the production line - requires a hefty investment and development of specialized machinery. In our approach, the center of the solution is the operator through sufficient and adequate instrumentation, real-time reporting and ergonomics. Efficiency and reduced cycle time can be achieved thorough the integration of Internet-of-Things (IoT) ready technologies into assembly operations to enhance the ergonomics of the workstations. Augmented reality visual aids, RFID triggered personalized workstation dimensions and real-time data transfer and reporting can help achieve these goals. In this case study, a standard work cell will be used for real-life data acquisition and a simulation software to extend the data points beyond the test cycle. Three comparison scenarios will run in the work cell. Each scenario will introduce a dimension of the ergonomics to measure its impact independently. Furthermore, the separate test will determine the limitations of the technology and provide a reference for operating costs and investment required. With the ability, to monitor costs, productivity, cycle time and scrap/waste in real-time the ROI (return on investment) can be determined at the different levels to integration. This case study will help to show that ergonomics in the assembly lines can make significant impact when IoT technologies are introduced. Ergonomics can effectively reduce waste and increase productivity with minimal investment if compared with setting up to custom machine.

Keywords: augmented reality visual aids, ergonomics, real-time data acquisition and reporting, RFID triggered workstation dimensions

Procedia PDF Downloads 190

Authors: Ana Lambelho

Abstract:

Nowadays is very common that an activity may be performed independently or dependently. In Portugal, the Labour Law exclusively protects the dependent labour relations. The independent work is regulated by civil law, where the autonomy of the will is the main principle. For companies is more advantageous to hire people under a service agreement since, in that case, the relation is not submitted to the limits established in Labour law and collective bargaining. This practice has nothing wrong, if the performance of work is, in fact, made autonomously. The problem is the increased frequency of the celebration of service agreements to hide a legal relation of subordination. Aware of this and regarding the huge difficulty to demonstrate the existence of subordinated work (that often runs against the employee), the Portuguese legislator devoted some legislative rules in order to facilitate the evidence of legal subordination and, on the other hand, to avoid the misuse of the provision of service agreements. This study focuses precisely on the analysis of this solution, namely the so-called presumption of ‘laboralidade’ and on the lawsuit to recognize the existence of a labour contract. The presumption of the existence of a labour contract is present in the Portuguese legal system since 2003, and received, with the 2009 Labour Code, a new redaction that, according to the doctrine and the jurisprudence, finally approached it to a legal presumption, with the consequent reversal of the burden of proof and, in consequence, made easier to proof the legal subordination, because the employee will just have to plead and prove the existence of two of the elements described in the law to use this presumption. Another change in the Portuguese legal framework is related with the competencies of the Authority for Working Conditions (AWC): now, if during an inspection, the Authority finds a situation that seems to be an undeclared employment situation, it may access the company and, if it does not regularize voluntarily the situation, AWC has a duty to communicate to the public prosecutor, who will begin the lawsuit for the recognition of the existence of an employment contract. To defend the public interest, the action to recognize the existence of an employment contract will follow its terms, even against the employee will. Although the existence of these mechanisms does not solve by itself the problem of evasion of labour law and false ‘green receipts’, it is undeniable that it is an important step in combating fraud in this field.

Keywords: independent work, labour contract, Portugal, service agreement

Procedia PDF Downloads 308

Authors: Zita Fomukong Andam

Abstract:

Civil disobedience according to John Rawls (1971) is a public nonviolent and conscientious breach of laws undertaken with the aim of bringing about a change in government laws and policies. Thus individuals who engage themselves in such an act are aware and ready to accept the consequences of their actions. Cameroon more precisely the Northwest and the Southwest region which are the English part are considered as one of the societies facing this act of civil disobedience. It has been a tormenting issue in the country affecting its economy and the tourism sector. This is because these regions known as one of the best touristic sites of the country is not more considered as a destination to be visited by tourist because of its insecurities. Many commercial buildings have been burning down, leaving many young Cameroonians jobless. Education has been hindered, and youths are forced to relocate to nearby cities in order to continue their education. This crisis has created a lot of insecurity throughout the regions thus youths now have one common interest to travel abroad either to seek refuge or to continue their education and even search for jobs. The purpose of this research is to assess the issue of civil disobedience, trying to understand why it is affected only by a specific region in a country while the others are doing fine. A deep research discourse was conducted with randomly selected individuals aging between 15 to 40 years living both in the destination and abroad. Survey questionnaires and interviews were carried out as a method to collect data. The results show that this crisis has impacted the local residents psychologically and has injected a lot of fears into tourists and they are no more willing to visit the destination. In addition, it has brought a negative impact on the county’s economy since tourism is considered as the key sector in a country’s economy. On the other hand, the results showed that many local residents have remained jobless, others have lost family members, and the daily routine life has been affected. Understanding these results, the national government and international bodies might be able to propose possible and efficient solutions in order to attain stability and security in this region.

Keywords: civil disobedience, economic impact, local residents, tourist

Procedia PDF Downloads 87

Authors: Payam Najafi, Behnam Ebrahimi, Hamid Montazerolghaem, Safoura Akbari-Alavijeh, Rasoul Tarkesh Esfahani

Abstract:

The combination of work and study has been recently gained lots of attention due to the crucial demand of industries to skillfully trained youth. Nevertheless, the distance between university and industry makes this combination challenging. According to the OECD (2012), in most countries, there is a limited link between students’ field of study and their area of work while studying. On the other hand, high unemployment rates among the specialized workforce, which is common in developing countries, highlights the need to strengthen this relationship. Innovative Center of Isfahan Chamber of Commerce has defined a project called 'POUYESH', which helps students to find related work opportunities to their field of study as well as supporting industries to supply their needed workforce. The present research is sought to explore the effect of the running project as a model of combining work and study on the university-industry linkage.

Keywords: work and study, university-industry linkage, POUYESH project, field of study

Procedia PDF Downloads 158

Authors: R. Barbour

Abstract:

Peace-building organisations act as a network of information for communities. Through fieldwork, it was highlighted that grassroots organisations and activists may cooperate with each other in their actions of peace-building; however, they would not collaborate. Within two divided societies; Nicosia in Cyprus and Jerusalem in Israel, there is a distinction made by organisations and activists with regards to activities being more ‘co-operative’ than ‘collaborative’. This theme became apparent when having informal conversations and semi-structured interviews with various members of the activist communities. This idea needs further exploration as these distinctions could impact upon the efficiency of peacebuilding activities within divided societies. Civil societies within divided landscapes, both physically and socially, play an important role in conflict resolution. How organisations and activists interact with each other has the possibility to be very influential with regards to peacebuilding activities. Working together sets a positive example for divided communities. Cooperation may be considered a primary level of interaction between CSOs. Therefore, at the beginning of a working relationship, organisations cooperate over basic agendas, parallel power structures and focus, which led to the same objective. Over time, in some instances, due to varying factors such as funding, more trust and understanding within the relationship, it could be seen that processes progressed to more collaborative ways. It is evident to see that NGOs and activist groups are highly independent and focus on their own agendas before coming together over shared issues. At this time, there appears to be more collaboration in Nicosia among CSOs and activists than Jerusalem. The aims and objectives of agendas also influence how organisations work together. In recent years, Nicosia, and Cyprus in general, have perhaps changed their focus from peace-building initiatives to more environmental issues which have become new-age reconciliation topics. Civil society does not automatically indicate like-minded organisations however solidarity within social groups can create ties that bring people and resources together. In unequal societies, such as those in Nicosia and Jerusalem, it is these ties that cut across groups and are essential for social cohesion. Societies are a collection of social groups; individuals who have come together over common beliefs. These groups in turn shape the identities and determine the values and structures within societies. At many different levels and stages, social groups work together through cooperation and collaboration. These structures in turn have the capabilities to open up networks to less powerful or excluded groups, with the aim to produce social cohesion which may contribute social stability and economic welfare over any extended period.

Keywords: collaboration, cooperation, grassroots activism, networks of communication

Procedia PDF Downloads 131

Authors: Ying Zhang

Abstract:

In ASME Boiler and Pressure Vessel Code, the plastic load is defined by applying the twice elastic slope (TES) criterion of plastic collapse to a characteristic load-deformation curve for the vessel. Several other plastic criterion such as tangent intersection (TI) criterion, plastic work (PW) criterion have been proposed in the literature, but all exhibit a practical limitation: difficult to define the load parameter for vessels subject to several combined loads. An alternative criterion: plastic work-tangent (PWT) criterion for evaluating plastic load in pressure vessel design by analysis is presented in this paper. According to the plastic work-load curve, when the tangent variation is less than a given value in the plastic phase, the corresponding load is the plastic load. Application of the proposed criterion is illustrated by considering the elastic-plastic response of the lower head of reactor pressure vessel (RPV) and nozzle intersection of (RPV). It is proposed that this is because the PWT criterion more fully represents the constraining effect of material strain hardening on the spread of plastic deformation and more efficiently ton evaluating the plastic load.

Keywords: plastic load, plastic work, strain hardening, plastic work-tangent criterion

Procedia PDF Downloads 331

Authors: Mesbah Tarek, Kelaiaia Samia, Chiheb Sofien, Kelaiaia Mounia Samira, Labar Hocine

Abstract:

Short circuit causes important damage in power systems. The aim of this paper is the investigation of the effect of short circuit at the AC side inverter in HVDC transmission line. The cutoff of HVDC transmission line implies important economic losses. In this paper it is proposed an efficient procedure which can protect and eliminate the fault quickly. The theoretical development and simulation are well detailed and illustrated.

Keywords: AC inverter, HVDC, short circuit, switcher gate, power system

Procedia PDF Downloads 541

Authors: Jie Yang, Jian-Min Meng

Abstract:

A GPU-based floating object detection scheme is presented in this paper which is designed for floating mine detection tasks. This system uses contrast and motion information to eliminate as many false positives as possible while avoiding false negatives. The GPU computation platform is deployed to allow detecting objects in real-time. From the experimental results, it is shown that with certain configuration, the GPU-based scheme can speed up the computation up to one thousand times compared to the CPU-based scheme.

Keywords: object detection, GPU, motion estimation, parallel processing

Procedia PDF Downloads 448

Authors: Iting Chiang, Cheng-Yu Wei, Chin-Teng Kuo, Po-Sheng Hsu, Yo-Lun Yang, Yung-Chang Kang, Chien-Chon Chen, Chih-Yuan Chen

Abstract:

In recent years, it is reported that microalloying of nitrogen atoms within traditional Cr-Mo-V hot work tool steels can achieve better high temperature mechanical properties, which thus leads to such metallurgical approach widely utilized in the several commercial advanced hot work tool steels. Although the performance of hot work tool steel can be improved better by alloy composition design strategy, the influence of processing parameters on the mechanical property, especially on the service life of hot work tool steel, is still not fully understood yet. A longer service life of hot work tool steel can decrease the manufacturing cost effectively and thus become a research hot spot. According to several previous studies, it is generally acknowledged the service life of hot work tool steels can be increased effectively as the steels possessing higher hardness and toughness due to the formation and propagation of microcracks within the steel can be inhibited effectively. Therefore, in the present research, the designed experiments are primarily to explore the synergistic effect of nitrogen content and austenitization conditioning on the mechanical properties of hot work tool steels has been conducted and analyzed. No matter the nitrogen content, the results indicated the hardness of hot work tool steels increased as the austenitization treatment executed at higher temperature. On the other hand, an optimum toughness of hot work tool steel can be achieved as the austenitization treatment performed at a suitable temperature range. The possible explanation of such metallurgical phenomenon has been also proposed and analyzed in the present research.

Keywords: hot work tool steel, Cr-Mo-V, toughness, hardness, TEM

Procedia PDF Downloads 38

Authors: Simegn Alemayehu Ayele

Abstract:

Abstract: On November 4, 2020, the Ethiopian government launched a military operation against the Tigray People's Liberation Front (TPLF) in Ethiopia's Tigray Province, sparking the beginning of the Tigray War. This study focuses on the most recent Tigray War as it explores the effects of the civil war on Ethiopia's import and export activity. This study examines the consequences of violence on Ethiopia's trade relations, including its trading partners, export volume, and import requirements, using a combination of qualitative and quantitative data. The research outcome showed that Ethiopia's trade activities have suffered significantly as a result of the Tigray conflict, with both imports and exports declining. Particularly, the violence has hampered logistics and transportation networks, which has reduced the number of products exported and imported. Furthermore, the conflict has weakened Ethiopia's trading relationships and reduced demand for Ethiopian commodities. The survey also reveals that some of Ethiopia's major trade routes have been closed as a result of the conflict, severely restricting trade activities. These findings underline the necessity for political stability and conflict resolution procedures to support the nation's import and export activity by indicating that civil war has substantial repercussions for Ethiopia's economic development and trade activities.

Keywords: import demands, logistic networks, trade partiners, trade relatinships

Procedia PDF Downloads 50

Authors: Moira Cordiner

Abstract:

As a result of an Australian university approving a policy to improve the quality of assessment practices, as an academic developer (AD) with expertise in criterion-referenced assessment commenced in 2008. The four-year appointment was to support 40 'champions' in their Schools. This presentation is based on the experiences of a group of Chemistry academics who worked with the AD to develop and implement an honours dissertation rubric. Honours is a research year following a three-year undergraduate year. If the standard of the student's work is high enough (mainly the dissertation) then the student can commence a PhD. What became clear during the process was that much more was at stake than just the successful development and trial of the rubric, including academics' reputations, university rankings and research outputs. Working with the champion-Head of School(HOS) and the honours coordinator, the AD helped them adapt an honours rubric that she had helped create and trial successfully for another Science discipline. A year of many meetings and complex power plays between the two academics finally resulted in a version that was critiqued by the Chemistry teaching and learning committee. Accompanying the rubric was an explanation of grading rules plus a list of supervisor expectations to explain to students how the rubric was used for grading. Further refinements were made until all staff were satisfied. It was trialled successfully in 2011, then small changes made. It was adapted and implemented for Medicine honours with her help in 2012. Despite coming to consensus about statements of quality in the rubric, a few academics found it challenging matching these to the dissertations and allocating a grade. They had had no time to undertake training to do this, or make overt their implicit criteria and standards, which some admitted they were using - 'I know what a first class is'. Other factors affecting grading included: the small School where all supervisors knew each other and the students, meant that friendships and collegiality were at stake if low grades were given; no external examiners were appointed-all were internal with the potential for bias; supervisors’ reputations were at stake if their students did not receive a good grade; the School's reputation was also at risk if insufficient honours students qualified for PhD entry; and research output was jeopardised without enough honours students to work on supervisors’ projects. A further complication during the study was a restructure of the university and retrenchments, with pressure to increase research output as world rankings assumed greater importance to senior management. In conclusion, much more was at stake than developing a usable rubric. The HOS had to be seen to champion the 'new' assessment practice while balancing institutional demands for increased research output and ensuring as many honours dissertations as possible met high standards, so that eventually the percentage of PhD completions and research output rose. It is therefore in the institution's best interest for this cycle to be maintained as it affects rankings and reputations. In this context, are rubrics redundant?

Keywords: explicit and implicit standards, judging quality, university rankings, research reputations

Procedia PDF Downloads 311

Authors: Enrico Maria la Forgia

Abstract:

Since the 80ies, in specific situations, France’s Muslims have enacted political actions to reply to attacks on their identity or assimilation attempts, using their religious affiliation as a resource for the organization and expression of collective claims. Indeed, despite Islam's internal sectarian and ethnic differences, religion may be politicized when minorities’ social and cultural rights are under attack. French Civil Society organizations, in this specific case with an Islamic background (ICSO - Islamic Civil Society Organizations), play an essential role in defending Muslims’ social and cultural rights. As a matter of fact, Civil Society organized on an ethnic or religious base is a way to strengthen minoritarian communities and their role as political actors, especially in multicultural contexts. Since the first 1983’s “Marche des Beurs” (slang word referring to French citizens with foreign origins), which involved many Muslims, the development of ICSO contributed to the strenghtening of Islam in France, here meant as a Social Movement aiming to constitute a French version of Islam, defending minorities’ cultural and religious rights, and change the perception of Islam itself in national society. However, since a visible and stigmatized minority, ICSO do not relate only to protests as a strategy to achieve their goals: on several occasions, pressure on authorities through personal networks and connections, or the introduction into public debates of bargaining through the exploitation of national or international crisis, might appear as more successfully - public discourses on minorities and Islam are generally considered favorable conditions to advance requests for cultural legitimation. The proposed abstract, based on a literary review and theoretical/methodological reflection on the state of knowledge on the topic, aims to open a new branch of studies and analysis of Civil Society and Social Movements in Europe, focusing on the French Islamic community as a political actor relating on ICSO to pressure society, local, and national authorities to improve Muslims' rights. The opted methodology relies on a qualitative approach based on ethnography and face-to-face interviews addressing heads and middle-high level activists from ICSO, in an attempt to individuate the strategies enacted by ICSO for mobilizing Muslims and build relations with, on one hand, local and national authorities; into the other, with actors belonging to the Civil Society/political sphere. The theoretical framework, instead, relies on the main Social Movements Theories (resources mobilization, political opportunity structure, and contentious/non-contentious movements), aiming to individuate eventual gaps in the analysis of Islamic Social Movements and Civil Society in minoritarian contexts.

Keywords: Islam, islamophobia, civil society, social movements, sociology, qualitative methodology, Islamic activism in social movement theory, political change, Islam as social movement, religious movements, protest and politics, France, Islamic civil society

Procedia PDF Downloads 59

Authors: Reem Abuiyada

Abstract:

This paper is an attempt to review the pursuance of social-work field practice run by the department of social work, Dhofar University, situated in Dhofar region, Sultanate of Oman. It assesses the students’ engagement in social work in local community training that equips them to practice their allocated tasks and management skills that in turn made them more educated in fieldwork concepts, and especially in helping to overcome the challenges experienced by the Omani community to bring them positive changes. Besides, this paper evaluates the efficacy of fieldwork practice from the students' standpoints in higher education. And, it assumes the fact that this practice helped the students in giving equal significance to academic instruction, preparing for them to face the futuristic professions in an effective way.

Keywords: social work field training, students, Dhofar University, Oman, education

Procedia PDF Downloads 163

Authors: Novawiguna Kemalasari, Ahmad Badawi Saluy

Abstract:

This research is a planned activity to find an objective answer to PT XYZ problem through scientific procedure. In this study, It was used quantitative research methods by using samples taken from a department selected by researchers. This study aims to analyze the influence of organizational culture, work discipline and work motivation on employee performance of Personal Care & Cosmetic Department (PCC) Flammable PT XYZ. This research was conducted at PT XYZ Personal Care & Cosmetic Department (PCC) Flammable involving 82 employees as respondents, the data were obtained by using questionnaires filled in self-rating by respondents. The data were analyzed by multiple linear regression model processed by using SPSS version 22. The result of research showed that organizational culture variable, work discipline and work motivation had significant effect to employee performance.

Keywords: organizational culture, work discipline, employee motivation, employees performance

Procedia PDF Downloads 219

Authors: Ridha Abdulla Al Hammam

Abstract:

Purpose: to measure the extent of perceived structural empowerment and work commitment the intensive care unit in SMC have in their work place. Background: nurses’ access to power structures (information, recourses, opportunity, and support) directly influences their productivity, retention, and job satisfaction. Exploring nurses’ level and sources of work commitment (affective, normative, and continuance) is very essential to guide nursing leaders making decisions to improve work environment to facilitate effective nursing care. Both concepts (Structural Empowerment and Work Commitment) were never investigated in our critical care unit. Methods: a sample of 50 nurses attained from the Intensive Care Unit (Adult). Conditions for Workplace Effectiveness Questionnaire and Three-Component Model Employee Commitment Survey were used to measure the two concepts respectively. The study is quantitative, descriptive, and correlational in design. Results: the participants reported moderate structural empowerment provided by their work place (M=15 out of 20). The sample perceived high access to opportunity mainly through gaining more skills (M=4.45 out of 5) where the rest power structures were perceived with moderate accessibility. The participants’ affective commitment (M=5.6 out of 7) to work in the ICU overweighed their normative and continuance commitment (M=5.1, M=4.9 out of 7) implying a stronger emotional connection with their unit. Strong positive and significant correlations were observed between the participants’ structural empowerment scores and all work commitment sources. Conclusion: these results provided an insight on aspects of work environment that need to be fostered and improved in our intensive care unit which have a direct linkage to nurses’ work commitment and potentially to their quality of care they provide.

Keywords: structural empowerment, commitment, intensive care, nurses

Procedia PDF Downloads 259