Search results for: Tube Feeding

Authors: Shima Soleimani, Steven Eckels

Abstract:

One area of special importance for surface-level study of heat exchangers is tubes with internal micro-fins (< 0.5 mm tall). Micro-finned surfaces are a kind of extended solid surface in which energy is exchanged with water that acts as the source or sink of energy. Significant performance gains are possible for either shell, tube, or double pipe heat exchangers if the best surfaces are identified. The parametric studies of micro-finned tubes that have appeared in the literature left some key parameters unexplored. Specifically, they ignored three-dimensional (3D) micro-fin configurations, conduction heat transfer in the fins, and conduction in the solid surface below the micro-fins. Thus, this study aimed at implementing a parametric study of 3D micro-finned tubes that considered micro-fin height and discontinuity features. A 3D conductive and convective heat-transfer simulation through coupled solid and periodic fluid domains is applied in a commercial package, ANSYS Fluent 19.1. The simulation is steady-state with turbulent water flow cooling inner wall of a tube with micro-fins. The simulation utilizes a constant and uniform temperature on the tube outer wall. Performance is mapped for 18 different simulation cases, including a smooth tube using a realizable k-ε turbulence model at a Reynolds number of 48,928. Results compared the performance of 3D tubes with results for the similar two-dimensional (2D) one. Results showed that the micro-fin height has greater impact on performance factor than discontinuity features in 3D micro-fin tubes. A transformed 3D micro-fin tube can enhance heat transfer and pressure drop up to 21% and 56% compared to a 2D one, respectfully.

Keywords: three-dimensional micro-finned tube, heat transfer, friction factor, heat exchanger

Procedia PDF Downloads 94

Authors: Shu-Bo Yang, Wei Wu, Yuan-Heng Liu

Abstract:

This research aims to design a heat-exchanger type of methanol reformer coupled with a preheating design in gPROMS® environment. The endothermic methanol steam reforming reaction (MSR) and the exothermic preferential oxidation reaction (PROX) occur in the inner tube and the outer tube of the reformer, respectively. The effective heat transfer manner between the inner and outer tubes is investigated. It is verified that the countercurrent-flow type reformer provides the higher hydrogen yield than the cocurrent-flow type. Since the hot spot temperature appears in the outer tube, an improved scheme is proposed to suppress the hot spot temperature by splitting the excess air flowing into two sites. Finally, an optimization algorithm for maximizing the hydrogen yield is employed to determine optimal operating conditions.

Keywords: methanol reformer, methanol steam reforming, optimization, simulation

Procedia PDF Downloads 310

Authors: Shima Soleimani, Steven Eckels

Abstract:

One area of special importance for the surface-level study of heat exchangers is tubes with internal micro-fins (< 0.5 mm tall). Micro-finned surfaces are a kind of extended solid surface in which energy is exchanged with water that acts as the source or sink of energy. Significant performance gains are possible for either shell, tube, or double pipe heat exchangers if the best surfaces are identified. The parametric studies of micro-finned tubes that have appeared in the literature left some key parameters unexplored. Specifically, they ignored three-dimensional (3D) micro-fin configurations, conduction heat transfer in the fins, and conduction in the solid surface below the micro-fins. Thus, this study aimed at implementing a parametric study of 3D micro-finned tubes that considered micro-fine height and discontinuity features. A 3D conductive and convective heat-transfer simulation through coupled solid and periodic fluid domains is applied in a commercial package, ANSYS Fluent 19.1. The simulation is steady-state with turbulent water flow cooling the inner wall of a tube with micro-fins. The simulation utilizes a constant and uniform temperature on the tube outer wall. Performance is mapped for 18 different simulation cases, including a smooth tube using a realizable k-ε turbulence model at a Reynolds number of 48,928. Results compared the performance of 3D tubes with results for the similar two-dimensional (2D) one. Results showed that the micro-fine height has a greater impact on performance factors than discontinuity features in 3D micro-fin tubes. A transformed 3D micro-fin tube can enhance heat transfer, and pressure drops up to 21% and 56% compared to a 2D one, respectfully.

Keywords: three-dimensional micro-fin tube, heat transfer, friction factor, heat exchanger

Procedia PDF Downloads 87

Authors: Leja Salciute

Abstract:

Mental health difficulties are one of the reasons for abnormal feeding behaviour. This is especially evident in a crisis situation. Abnormal feeding behaviour occurs when individuals use food as a method to provide relief for these negative emotions. The study aimed to discover an association between emotional regulation, mental health difficulties and disruption in feeding behaviours in the UK in times of crisis. A mixed-methods design was used. Abnormal feeding behaviour was measured using the Binge Eating Disorder Screener-7, SCOFF scale, Crisis impact scale, Difficulties in Emotion Regulation Scale and demographics. The sample comprised 342 participants with a history of excessive overeating. The participants (male= 198, female= 141 and other= 3) came from the general population and they were aged 16 and over. Participants ranged in age from 16 to 89. Findings from the survey concluded that difficulties with emotion regulation were found to be associated with abnormal feeding behaviours. Mental health difficulties correlated significantly with changes in individuals’ lives, such as work or routines. Individuals differed in their abnormal feeding behaviour in terms of their age, that is, younger individuals showed less struggle with their eating patterns while older individuals faced greater struggles with their abnormal feeding behaviour. Emotion regulation significantly influenced abnormal feeding behaviour. Results from qualitative data suggest four common themes that were identified: demonstration of gratitude, negative emotions, disruptions to social life, and financial loss. For example, participants developed and gained an awareness of being grateful for the simple things in life even when participants experienced hardships. The results also suggested that emotional eating acted like a sedative that allowed the participant to run away from their painful reality. Crisis situation negatively affected relationships among participants and induced negativity related to social interaction. Finally, the respondents highlighted that the presence of uncertainty made it hard to plan ahead and look forward to the future. Although respondents experienced negative emotions and financial losses, some of them still managed to allocate time for themselves and enjoy their time off during crisis. However, majority of respondents referred to their inability to control their external circumstances and turned to and relied upon food overconsumption instead. This had a negative effect on their mental health and presented disruptions in feeding behaviour. It was recommended for individuals in times of crisis to seek psychological support in the form of Cognitive Behavioural Therapy (CBT).

Keywords: binge eating, maladaptive eating behaviours, mental health, negative emotions in crisis

Procedia PDF Downloads 43

Authors: Otgonjargal Damdinbaljir

Abstract:

Background: Infant feeding practices have a major role in determining the nutritional status of children and are associated with household socioeconomic and demographic factors. In 2010, Mongolia used WHO 2008 edition of Indicators for assessing infant and young child feeding practices for the first time. Objective: To evaluate the feeding status of infants and young children under 2 years old in Mongolia. Materials and Methods: The study was conducted by cluster random sampling. The data on breastfeeding and complementary food supplement of the 350 infants and young children aged 0-23 months in 21 provinces of the 4 economic regions of the country and capital Ulaanbaatar city were collected through questionnaires. The feeding status was analyzed according to the WHO 2008 edition of Indicators for assessing infant and young child feeding practices. Analysis of data: Survey data was analysed using the PASW statistics 18.0 and EPI INFO 2000 software. For calculation of overall measures for the entire survey sample, analyses were stratified by region. Age-specific feeding patterns were described using frequencies, proportions and survival analysis. Logistic regression was done with feeding practice as dependent and socio demographic factors as independent variables. Simple proportions were calculated for each IYCF indicator. The differences in the feeding practices between sexes and age-groups, if any, were noted using chi-square test. Ethics: The Ethics Committee under the auspices of the Ministry of Health approved the study. Results: A total of 350 children aged 0-23 months were investigated. The rate of ever breastfeeding of children aged 0-23 months reached up to 98.2%, while the percentage of early initiation of breastfeeding was only 85.5%. The rates of exclusive breastfeeding under 6 months, continued breastfeeding for 1 year, and continued breastfeeding for 2 years were 71.3%, 74% and 54.6%, respectively. The median time of giving complementary food was the 6th month and the weaning time was the 9th month. The rate of complementary food supplemented from 6th-8th month in time was 80.3%. The rates of minimum dietary diversity, minimum meal frequency, and consumption of iron-rich or iron-fortified foods among children aged 6-23 months were 52.1%, 80.8% (663/813) and 30.1%, respectively. Conclusions: The main problems revealed from the study were inadequate category and frequency of complementary food, and the low rate of consumption of iron-rich or iron-fortified foods were the main issues to be concerned on infant feeding in Mongolia. Our findings have highlighted the need to encourage mothers to enrich their traditional wheat- based complementary foods add more animal source foods and vegetables.

Keywords: complementary feeding, early initiation of breastfeeding, exclusive breastfeeding, minimum meal frequency

Procedia PDF Downloads 456

Authors: Ifeoma C. Afiaenyi, Elizabeth K. Ngwu, Rufina N. B. Ayogu

Abstract:

Diabetes has crept into the rural areas of Nigeria, causing devastating effects on its sufferers; most of them could not afford diabetic medications. Moringa oleifera has been used extensively in animal models to demonstrate its antilipidaemic and haematinic qualities; however, there is a scarcity of data on the effect of graded levels of Moringa oleifera leaves on the lipid profile and hematological parameters in human diabetic subjects. The study determined the effect of Moringa oleifera leaves on the lipid profile and hematological parameters of type 2 diabetic subjects in Ukehe, a rural Nigerian community. Twenty-four adult male and female diabetic subjects were purposively selected for the study. These subjects were shared into four groups of six subjects each. The diets used in the study were isocaloric. A control group (diabetics, group 1) was fed diets without Moringa oleifera leaves. Experimental groups 2, 3 and 4 received 20g, 40g and 60g of Moringa oleifera leaves daily, respectively, in addition to the diets. The subjects' lipid profile and hematological parameters were measured prior to the feeding trial and at the end of the feeding trial. The feeding trial lasted for fourteen days. The data obtained were analyzed using the computer program Statistical Product for Service Solution (SPSS) for windows version 21. A Paired-samples t-test was used to compare the means of values collected before and after the feeding trial within the groups and significance was accepted at p < 0.05. There was a non-significant (p > 0.05) decrease in the mean total cholesterol of the subjects in groups 1, 2 and 3 after the feeding trial. There was a non-significant (p > 0.05) decrease in the mean triglyceride levels of the subjects in group 1 after the feeding trial. Groups 1 and 3 subjects had a non-significant (p > 0.05) decrease in their mean low-density lipoprotein (LDL) cholesterol after the feeding trial. Groups 1, 2 and 4 had a significant (p < 0.05) increase in their mean high-density lipoprotein (HDL) cholesterol after the feeding trial. A significant (p < 0.05) decrease in the mean hemoglobin level was observed only in group 4 subjects. Similarly, there was a significant (p < 0.05) decrease in the mean packed cell volume of group 4 subjects. It was only in group 4 that a significant (p < 0.05) decrease in the mean white blood cells of the subjects was also observed. The changes observed in the parameters assessed were not dose-dependent. Therefore, a similar study of longer duration and more samples is imperative to authenticate these results.

Keywords: anemia, diabetic subjects, lipid profile, moringa oleifera

Procedia PDF Downloads 161

Authors: Olufemi Samuel Shola, Oladapo Adenike Adesola

Abstract:

Inadequate dietary intake has increased the susceptibility of under five children to malnutrition and infections. This study, therefore, assessed the feeding practices of children of 0-23 months of age among mothers in urban areas of Akure, Ondo State, Nigeria. Simple random sampling technique was used to select four hundred (400) mothers out of 710 mothers from 7 primary health care centres in Akure metropolis for the study. Data were collected using modified WHO 2003 Questionnaire on child feeding practices. Data were analyzed using descriptive statistics, while chi-square was used to determine the association between variables. Results showed that 52.0% of the children were males, with 47.5% in the 6-8 months age group. More than half (57.0%) of the mothers were between the ages of 20-29 years, and 45.0% had secondary education. Majority (94.3%) of the mothers breastfed their children in the last 24 hours preceding the survey. The feeding practices history of mothers showed that 28.0% and 53.7% of the mothers initiated breastfeeding less than 30 minutes and between 30 minutes to 1 hour after delivery, respectively. Also, 52.0% of mothers practiced exclusive breastfeeding for six months, while 26.2% breastfed from 6 months up to 2 years of age. Dietary diversity of the children age 6-23 months revealed that 68.7% of the children attained the minimum dietary diversity by consuming 4 or more food groups in the last 24 hours. There was a significant association (P < 0.05) between mothers’ education (n=180), occupation(n=41) and dietary diversity (n= 150) and meal frequency (n=209). Therefore, the study concluded that the duration of breastfeeding and time of introduction of complementary food did not meet WHO recommended guidelines. There is urgent need to launching more programmes.

Keywords: breastfeeding, mothers, child feeding, urban areas, ondo state, nigeria

Procedia PDF Downloads 95

Authors: Baboo Ali, Avni Ugur

Abstract:

Pesticide namely, Diflubenzuron, is tremendously used in pear orchards against different insect pests of pear fruit trees in Turkey. The predatory bug, Anthocoris nemoralis (F.) is found in pear orchard feeding on Cacopsylla pyri (L.) (Homoptera: Psyllidae), is an insect pest of pear fruit trees. In this study, the effectiveness of the above mentioned pesticide on various biological stages of predatory bug were investigated under laboratory conditions of 25±1˚C, 75±5% RH, and photoperiod of 16L: 8D h. Newly emerged 1st, 2nd, 3rd, 4th and 5th instars as well as the female and male stages of the predatory bug were placed on treated petri dishes and their mortality was checked after every 24 hours till the survival of the last individual. Prey consumption of surviving instars as well as the adult stages was determined simultaneously. All biological stages of the predatory bug were fed with eggs of Ephestia kuehniella during the whole research work. Percent hatch of treated eggs was recorded after every 24 hours, and the behavioral test of the male and female stages against Diflubenzuron was also determined using Y-tube olfactometer. Consequently, the mortality rate of 1st, 2nd, 3rd, 4th, and 5th instars was 61.32 %, 67.50%, 74. 91%, 80.11%, and 83.04%, respectively. In case of male and female stages, it has been recorded as 95.47% and 95.50%, respectively. Thus, a significant difference was not found between female and male mortality rates. Prey consumption of 1st, 2nd, 3rd, 4th and 5th surviving instars was noted as 8.01, 11. 72, 13.24, 16.93 and 20.49 number of eggs/day while in females and males, it was 12.05 and 12.71 number of eggs/day, respectively. Hatching ratio of treated eggs of predator was 25.32±4.08. As far as the behavioral test is concerned, it has been indicated that Diflubenzuron has 65% repellent effect on the newly emerged male and female stages of the predatory bug while using Y-tube olfactometer under laboratory conditions.

Keywords: behavior, biological stages, diflubenzuron, effectiveness, pesticide, predatory bug

Procedia PDF Downloads 495

Authors: Mianheng Lai, Johnny Ching Ming Ho, Hoat Joen Pam

Abstract:

Concrete-filled-steel-tube (CFST) columns are becoming increasingly popular owing to the superior behavior contributed by the composite action. However, this composite action cannot be fully developed because of different dilation properties between steel tube and concrete. During initial compression, there will be de-bonding between the constitutive materials. As a result, the strength, initial stiffness and ductility of CFST columns reduce significantly. To resolve this problem, external confinement in the form of spirals is proposed to improve the interface bonding. In this paper, a total of 14CFST columns with high-strength as well as ultra-high-strength concrete in-filled were fabricated and tested under uni-axial compression. From the experimental results, it can be concluded that the proposed spirals can improve the strength, initial stiffness, ductility and the interface bonding condition of CFST columns by restraining the lateral expansion of steel tube and core concrete. Moreover, the failure modes of confined core concrete change due to the strong confinement provided by spirals.

Keywords: concrete-filled-steel-tube, confinement, failure mode, high-strength concrete, spirals

Procedia PDF Downloads 330

Authors: Manish Chand, Subhrojit Bagchi, R. Kumar

Abstract:

A new dry tube (DT) has been installed in the tank of KAMINI research reactor, Kalpakkam India. This tube will be used for neutron activation analysis of small to large samples and testing of neutron detectors. DT tube is 375 cm height and 7.5 cm in diameter, located 35 cm away from the core centre. The experimental thermal flux at various axial positions inside the tube has been measured by irradiating the flux monitor (¹⁹⁷Au) at 20kW reactor power. The measured activity of ¹⁹⁸Au and the thermal cross section of ¹⁹⁷Au (n,γ) ¹⁹⁸Au reaction were used for experimental thermal flux measurement. The flux inside the tube varies from 10⁹ to 10¹⁰ and maximum flux was (1.02 ± 0.023) x10¹⁰ n cm⁻²s⁻¹ at 36 cm from the bottom of the tube. The Au and Zr foils without and with cadmium cover of 1-mm thickness were irradiated at the maximum flux position in the DT to find out the irradiation specific input parameters like sub-cadmium to epithermal neutron flux ratio (f) and the epithermal neutron flux shape factor (α). The f value was 143 ± 5, indicates about 99.3% thermal neutron component and α value was -0.2886 ± 0.0125, indicates hard epithermal neutron spectrum due to insufficient moderation. The measured flux profile has been validated using theoretical model of KAMINI reactor through Monte Carlo N-Particle Code (MCNP). In MCNP, the complex geometry of the entire reactor is modelled in 3D, ensuring minimum approximations for all the components. Continuous energy cross-section data from ENDF-B/VII.1 as well as S (α, β) thermal neutron scattering functions are considered. The neutron flux has been estimated at the corresponding axial locations of the DT using mesh tally. The thermal flux obtained from the experiment shows good agreement with the theoretically predicted values by MCNP, it was within ± 10%. It can be concluded that this MCNP model can be utilized for calculating other important parameters like neutron spectra, dose rate, etc. and multi elemental analysis can be carried out by irradiating the sample at maximum flux position using measured f and α parameters by k₀-NAA standardization.

Keywords: neutron flux, neutron activation analysis, neutron flux shape factor, MCNP, Monte Carlo N-Particle Code

Procedia PDF Downloads 131

Authors: The Nan Chang, Ping-Tang Yu, Jyun-Ming Lin

Abstract:

A triple band circularly polarized antenna covering 1.17, 1.22, and 1.57 GHz is presented. To extend to the triple-band operation, we need to add one more ring while maintaining the mechanism to independently control each ring. The inset-part in the feeding scheme is used to excite the band at 1.22 GHz, while the proximate-part of the feeding scheme is used to excite not only the band at 1.57 GHz but also the band at 1.17 GHz. This is achieved by up-vertically coupled with one ring to radiate at 1.57 GHz and down-vertically coupled another ring to radiate at 1.17 GHz. It is also noted that the inset-part in our feeding scheme is by horizontal coupling. Furthermore, to increase the gain at all three bands, three air-layers are added to make the total height of the antenna be 7.8 mm. The total thickness of the three air-layers is 3 mm. The gains of the three bands are all greater than 5 dBiC after adding the air-layers.

Keywords: circular polarization, global position system, high gain, triband antenna

Procedia PDF Downloads 211

Authors: Tran Gia Khanh, Dao Phuong Nam, Do Trong Tan, Nguyen Van Huong, Mai Xuan Sinh

Abstract:

This work presents the problem of tube-based robust model predictive controller for a class of continuous-time systems in the presence of input disturbances. The main objective is to point out the state trajectory of closed system being maintained inside a sequence of tubes. An estimation of attraction region of the closed system is pointed out based on input state stability (ISS) theory and linearized model in each time interval. The theoretical analysis and simulation results demonstrate the performance of the proposed algorithm for a wheeled inverted pendulum system.

Keywords: input state stability (ISS), tube-based robust MPC, continuous-time nonlinear systems, wheeled inverted pendulum

Procedia PDF Downloads 191

Authors: Sophia Anastasiou, Cosmas Nathanailides, Fotini Kakali, Panagiotis Logothetis, Gregorios Kanlis

Abstract:

The method and rearing conditions of aquaculture may very between different regions and aquaculture sites. Globally, the Aquaculture industry faces a challenge to develop aquaculture methods which safeguard the economic viability of the company, the welfare of farmed fish and final product quality and sustainable development of aquaculture. Marine fish farms in Greece operate in different locations and farmed fish are exposed to a variety of rearing conditions. This paper investigates the variability of product quality and the financial performance of different marine fish farms operating in West Greece. Production parameters of gilthead sea bream fish farm such as feeding regimes, mortalities, fish densities were used to calculate the economic efficiency of six different aquaculture sites from West Greece. Samples of farmed sea bream were collected and lipid content, microbial load and filleting yield of the samples were used as quality criteria. The results indicate that Lipid content, filleting yield and microbial load of fish originating from different fish farms varied significantly with improved quality exhibited in fish farms which exhibited improved Feed conversion rates and lower mortalities. Changes in feeding management practices such as feed quality and feeding regimes have a significant impact on the financial performance of sea bass farms. Fish farms which exhibited improved feeding conversion rates also exhibited increased profitability. Improvements in the FCR explained about 13.4 % of the difference in profitability of the different aquaculture sites. Lower mortality and higher growth rates were also exhibited by the fish farms which exhibited improved FCR. It is concluded that best feeding management practices resulted in improved product quality and profitability.

Keywords: fish quality, aquaculture management, feeding management, profitability

Procedia PDF Downloads 447

Authors: B. U. Ibrahim, A. Okafor

Abstract:

Sixty-two (62) samples of Clarias anguillaris were collected from Tagwai Reservoir and used for the study. 29 male and 33 female samples were obtained for the study. Body measurement indicated that different sizes were collected for the study. Males, females and combined sexes had standard length and total length means of 26.56±4.99 and 31.13±6.43, 27.17±5.21 and 30.62±5.43, 26.88±5.08 and 30.86±5.88 cm, respectively. The weights of males, females and combined sexes have mean weights of 241.10±96.27, 225.75±78.66 and 232.93±86.95 gm, respectively. Eight items; fish, insects, plant materials, sand grains, crustaceans, algae, detritus and unidentified items were eaten as food by Clarias anguilarias in Tagwai Reservoir. Frequency of occurrence and numerical methods used in stomach contents analysis indicated that fish was the highest, followed by insect, while the lowest was the algae. Frequency of stomach fullness of Clarias anguillaris showed low percentage of empty stomachs or stomachs without food (21.00%) and high percentage of stomachs with food (79.00%), which showed high abundance of food and high feeding intensity during the period of study. Classification of fish based on feeding habits showed that Clarias anguillaris in this study is an omnivore because it consumed both plant and animal materials.

Keywords: stomach content, feeding habit, Clarias anguillaris, Tagwai Reservoir

Procedia PDF Downloads 566

Authors: Mirza Popovac

Abstract:

This paper investigates the application of the vortex tubes towards increasing the efficiency of high temperature heat pumps based on natural refrigerants, by recovering a part of the expansion work within the refrigerant cycle. To this purpose the 3D Navier-Stokes solver is used to perform a set of numerical simulations, investigating the vortex tube performance. Firstly, the fluid flow and heat transfer characteristics are analyzed for standard configurations of vortex tubes, and the obtained results are validated against the experimental and numerical data available in literature. Subsequently, different geometry specifications are analyzed, as well as the interplay between relevant heat pump operating conditions and the properties of natural refrigerants. Finally, the characteristic curve of performance will be derived for investigated vortex tubes specifications when used within high temperature heat pumps.

Keywords: heat pump, vortex tube, CFD, natural refrigerant

Procedia PDF Downloads 114

Authors: M. Kamal M. Shah, Noorhifiantylaily Ahmad, O. Irma Wani, J. Sahari

Abstract:

This paper presents the computationally mechanics analysis of energy absorption for cylindrical and square thin wall tubed structure by using ABAQUS/explicit. The crashworthiness behavior of AISI 1020 mild steel thin-walled tube under axial loading has been studied. The influence effects of different model’s cross-section, as well as model length on the crashworthiness behavior of thin-walled tube, are investigated. The model was placed on loading platform under axial loading with impact velocity of 5 m/s to obtain the deformation results of each model under quasi-static loading. The results showed that model undergoes different deformation mode exhibits different energy absorption performance.

Keywords: axial loading, computational mechanics, energy absorption performance, crashworthiness behavior, deformation mode

Procedia PDF Downloads 408

Authors: Ahmed E. Hodaib, Muhammed A. Hashem

Abstract:

High-speed transportation has become a growing concern. To increase high-speed efficiencies and minimize power consumption of a vehicle, we need to eliminate the friction with the ground and minimize the aerodynamic drag acting on the vehicle. Due to the complexity and high power requirements of electromagnetic levitation, we make use of the air in front of the capsule, that produces the majority of the drag, to compress it in two phases and inject a proportion of it through small nozzles to make a high-pressure air cushion to levitate the capsule. The tube is partially-evacuated so that the air pressure is optimized for maximum compressor effectiveness, optimum tube size, and minimum vacuum pump power consumption. The total relative mass flow rate of the tube air is divided into two fractions. One is by-passed to flow over the capsule body, ensuring that no chocked flow takes place. The other fraction is sucked by the compressor where it is diffused to decrease the Mach number (around 0.8) to be suitable for the compressor inlet. The air is then compressed and intercooled, then split. One fraction is expanded through a tail nozzle to contribute to generating thrust. The other is compressed again. Bleed from the two compressors is used to maintain a constant air pressure in an air tank. The air tank is used to supply air for levitation. Dividing the total mass flow rate increases the achievable speed (Kantrowitz limit), and compressing it decreases the blockage of the capsule. As a result, the aerodynamic drag on the capsule decreases. As the tube pressure decreases, the drag decreases and the capsule power requirements decrease, however, the vacuum pump consumes more power. That’s why Design optimization techniques are to be used to get the optimum values for all the design variables given specific design inputs. Aerodynamic shape optimization, Capsule and tube sizing, compressor design, diffuser and nozzle expander design and the effect of the air bearing on the aerodynamics of the capsule are to be considered. The variations of the variables are to be studied for the change of the capsule velocity and air pressure.

Keywords: tube-capsule, hyperloop, aerodynamic design optimization, air compressor, air bearing

Procedia PDF Downloads 303

Authors: S. H. Chew, Z. X. Eng, K. E. Chuah, T. Y. Lim, H. M. A. Yim

Abstract:

In recent years, geotextile tube has been widely used in the hydraulic engineering and dewatering industry. To construct a stable containment bund with geotextile tubes, the sand slurry is always the preference infilling material. However, the shortage of sand supply posts a problem in Singapore to adopt this construction method in the actual construction of long containment bund. Hence, utilizing the soft dredged clay or the excavated soft clay as the infilling material of geotextile tubes has a great economic benefit. There are any technical issues with using this soft clayey material as infilling material, especially on the excessive settlement and stability concerns. To minimize the shape deformation and settlement of geotextile tube associated with the use of this soft clay infilling material, a modified innovative infilling material is proposed – lightly cemented soft clay. The preliminary laboratory studies have shown that the dewatering mechanism via geotextile material of the tube skin, and the introduction of cementitious chemical action of the lightly cemented soft clay will accelerate the consolidation and improve the shear strength of infill material. This study aims to extend the study by conducting a pilot test of the geotextile tube filled with lightly cemented clay. This study consists of testing on a series of miniature geo-tubes and two full-size geotextile tube. In the miniature geo-tube tests, a number of small scaled-down size of geotextile tubes were filled with cemented clay (at water content of 150%) with cement content of 0% to 8% (by weight). The shear strength development of the lightly cemented clay under dewatering mechanism was evaluated using a modified in-situ Cone Penetration Test (CPT) at 0 days, 3 days, 7 days and 28 days after the infilling. The undisturbed soil samples of lightly cemented infilled clay were also extracted at 3-days and 7-days for triaxial tests and evaluation of final water content. The results suggested that the geotextile tubes filled with un-cemented soft clay experienced very significant shape change over the days (as control test). However, geotextile mini-tubes filled with lightly cemented clay experienced only marginal shape changed, even that the strength development of this lightly cemented clay inside the tube may not show significant strength gain at the early stage. The shape stability is believed to be due to the confinement effect of the geotextile tube with clay at non-slurry state. Subsequently, a full-scale instrumented geotextile tube filled with lightly cemented clay was performed. The extensive results of strain gauges and pressure transducers installed on this full-size geotextile tube demonstrated a substantial mobilization of tensile forces on the geotextile skin corresponding to the filling activity and the subsequent dewatering stage. Shape change and the in-fill material strength development was also monitored. In summary, the construction of containment bund with geotextile tube filled with lightly cemented clay is found to be technically feasible and stable with the use of the sufficiently strong (i.e. adequate tensile strength) geotextile tube, the adequate control on the dosage of cement content, and suitable water content of infilling soft clay material.

Keywords: cemented clay, containment bund, dewatering, geotextile tube

Procedia PDF Downloads 247

Authors: Ali Motevalli, Shahin Nayyeri Amiri

Abstract:

Cross-Hole Sonic Logging (CSL) is a common type of Non-Destructive Testing (NDT) method, which is currently used to check the integrity of placed drilled shafts. CSL evaluates the integrity of the concrete inside the cage and between the access tubes based on propagation of ultrasonic waves between two or more access tubes. A number of access tubes are installed inside the reinforcing cage prior to concrete placement as guides for sensors. The access tubes can be PVC or steel galvanized based on ASTM6760. The type of the CSL tubes can affect the axial strength of the drilled shaft. The objective of this study is to compare the amount of axial load capacity of drilled shafts due to using a different type of CSL tubes inside the caging. To achieve this, three (3) large-scale drilled shaft samples were built and tested using a hydraulic actuator at the Florida International University’s (FIU) Titan America Structures and Construction Testing (TASCT) laboratory. During the static load test, load-displacement curves were recorded by the data acquisition system (MegaDAC). Three drilled shaft samples were built to evaluate the effect of the type of the CSL tube on the axial load capacity in drilled shaft foundations.

Keywords: drilled shaft foundations, axial load capacity, cage, PVC, galvanized tube, CSL tube

Procedia PDF Downloads 379

Authors: U. Pangnakorn, S. Kanlaya

Abstract:

The efficiency of wood vinegar mixed with each individual of three plants extract such as: citronella grass (Cymbopogon nardus), neem seed (Azadirachta indica A. Juss), and yam bean seed (Pachyrhizus erosus Urb.) were tested against the second instar larvae of housefly (Musca domestica L.). Steam distillation was used for extraction of the citronella grass while neem and yam bean were simple extracted by fermentation with ethyl alcohol. Toxicity test was evaluated in laboratory based on two methods of larvicidal bioassay: topical application method (contact poison) and feeding method (stomach poison). Larval mortality was observed daily and larval survivability was recorded until the survived larvae developed to pupae and adults. The study resulted that treatment of wood vinegar mixed with citronella grass showed the highest larval mortality by topical application method (50.0%) and by feeding method (80.0%). However, treatment of mixed wood vinegar and neem seed showed the longest pupal duration to 25 day and 32 days for topical application method and feeding method respectively. Additional, larval duration on treated M. domestica larvae was extended to 13 days for topical application method and 11 days for feeding method. Thus, the feeding method gave higher efficiency compared with the topical application method.

Keywords: housefly (Musca domestica L.), neem seed (Azadirachta indica), citronella grass (Cymbopogon nardus), yam bean seed (Pachyrhizus erosus), mortality

Procedia PDF Downloads 314

Authors: Dhawal Ladani

Abstract:

Shell and tube type heat exchangers are predominantly used in heat exchange between two fluids and other applications. This paper projects the optimal design of the pipe used in the heat exchanger in such a way to minimize the vibration occurring in the pipe. Paper also consists of the comparison of the different design of the pipe to get the maximize the heat transfer rate by converting laminar flow into the turbulent flow. By the updated design the vibration in the pipe due to the flow is also decreased. Computational Fluid Dynamics and Thermal Heat Transfer analysis are done to justifying the result. Currently, the straight pipe is used in the shell and tube type of heat exchanger where as per the paper the pipe consists of the curvature along with the pipe. Hence, the heat transfer area is also increased and result in the increasing in heat transfer rate. Curvature type design is useful to create turbulence and minimizing the vibration, also. The result will give the output comparison of the effect of laminar flow and the turbulent flow in the heat exchange mechanism, as well as, inverse effect of the boundary layer in heat exchanger is also justified.

Keywords: heat exchanger, heat transfer rate, laminar and turbulent effect, shell and tube

Procedia PDF Downloads 282

Authors: Khosru M. Salim, Md. Jasim Uddin, Mohammad Rejwan Uddin

Abstract:

Developing countries like Bangladesh has huge population lives in the rural areas out of electricity. They are using manually operated tube well for collecting underground water to meet their daily demand. A human labour is required to lift water from tube well. Sometimes, it is impossible for a elementary school going child to operate a tube well in the school. Solar powered water pump could be a sustainable water pumping solution in the rural area of Bangladesh. To minimize the cost, a 0.5 horse power solar water pump is designed considering the requirement of water for a typical house hold in this research. A prototype of the 0.5 hp capacity system is implemented and tested in the rooftop of the university lab to validate the performances. Based on the experimental data, the performance of the system is analyzed and presented in this paper.

Keywords: water pump, solar photovoltaic module, performance analysis, feasibility study

Procedia PDF Downloads 279

Authors: Clementina Ebere Okoro, Olumuyiwa Adeyemi Owolabi, Doris Bola James, Aloysius Nwabugo Maduforo, Andrew Lingililani Mbewe, Christopher Osaruwanmwen Isokpunwu

Abstract:

Poor dietary practices and malnutrition, including severe acute malnutrition among under-five children in Nigeria has remained a great public health concern. This study assessed infant and young child feeding practices and nutritional status of under-five children to determine the prevalence of malnutrition of under-five children in Kuje area council, Abuja. The study was a cross-sectional study. Multi-stage sampling techniques was used in selecting the population that was studied. Probability proportion by size was applied in choosing 30 clusters for the survey using ENA for SMART software 2011 version. Questionnaires were used to obtain information from the population, while appropriate equipment was used for measurements of anthropometric parameters. The data was also subjected to statistical analysis. Results were presented in tables and figures. The result showed that 96.7% of the children were breastfed, 30.6% had early initiation to breastfeeding within first hour of birth and 22.4% were breastfed exclusively up to 6 months, 69.8% fed infants’ colostrum, while 30.2% discarded colostrum. About half of the respondents (49.1%) introduced complementary feeding before six months and 23.2% introduced it after six months while 27.7% had age appropriate timely introduction of complementary feeding. The anthropometric result showed that the prevalence of global acute malnutrition (GAM) was 12.8%, severe wasting prevalence was 5.4%, moderate wasting was 7.4%, underweight was 24.4%, stunting was 40.3% and overweight was 7.0%. The result showed that there is a high prevalence of malnutrition among under-five children in Kuje

Keywords: malnutrition, under five children, breastfeeding, complementary feeding

Procedia PDF Downloads 231

Authors: Behnaz Farahani, Razieh Sotoudeh, Ali Vahdani, Hamed Abdi

Abstract:

Individual differences in eating behavior can cause underweight or overweight and obesity. Thus influencing factors on children’s eating behavior such as mothers’ feeding practices are needed to be more investigated. The goals of this survey are to evaluate the association of (i) parental pressure and children’s food avoidant tendency, (ii) parental restriction and children’s food approach tendency, (iii) modeling of healthy eating in front of children and their children’s eating behavior. 760 mothers of children aged 7-10 from schools in Isfahan were asked to complete questionnaires including Child Feeding Questionnaire, Children’s Eating Behavior Questionnaire, Modeling Questionnaire, and self-administered demographic questionnaire in which mothers reported their children’s height and weight as well. Of those mothers, 745 completed the questionnaires for the children’s index (mean age: 8.513±1.112) during the 2011-2012 school year. The results of this quantitative, descriptive, cross-sectional analysis indicated that “parental restriction” was positively associated with child food responsiveness (P,0.000) and food enjoyment (P,0.000) and surprisingly, it was positively associated with Food Fussiness(0.000) .Parental pressure to eat was positively associated with child satiety responsiveness (P,0.000), slowness (P,0.000), and fussiness (P,0.00) and negatively associated with Food responsiveness(p,0.000)and Enjoyment of food (p,0.002), modeling of healthy eating were positively associated with Enjoyment of food / q (p,0.000) and negatively with food fussiness (P,0.000). The results of this survey will improve interventions and maternal guidance on their feeding practices and their association with children’s eating behavior and weight.

Keywords: feeding practices, eating behavior, pressure to eat, restriction, modeling, satiety responsiveness, slowness in eating, food fussiness, food responsiveness, enjoyment of food

Procedia PDF Downloads 588

Authors: Mohamed M. Abo Elazm, Ali I. Shehata, Mohamed M. Khairat Dawood

Abstract:

A computational fluid dynamics (CFD) program FLUENT has been used to predict the fluid flow and heat transfer distribution within concentric heat exchangers. The effect of inlet inclination angle has been investigated with Reynolds number range (3000 – 4000) and Pr=0.71. The heat exchanger is fabricated from copper concentric inner tube with a length of 750 mm. The effects of hot to cold inlet flow rate ratio (MH/MC), Reynolds's number and of inlet inclination angle of 30°, 45°, 60° and 90° are considered. The results showed that the numerical prediction shows a good agreement with experimental measurement. The results present an efficient design of concentric tube heat exchanger to enhance the heat transfer by increasing the swirling effect.

Keywords: heat transfer, swirling effect, CFD, inclination angle, concentric tube heat exchange

Procedia PDF Downloads 289

Authors: Sisay Shine, Frew Tadesse, Zemenu Shiferaw, Lema Mideksa

Abstract:

Background: Stunting is one of the most important public health problems in Ethiopia with an estimated 44.4% of children less than five years of age are stunted. Thus, this study aimed to assess prevalence and associated factors of stunting among 6-59 months children in pastoral community of Korahay Zone, Somali Regional State, Ethiopia. Objective of the study: To assess prevalence and associated factors of stunting among 6-59 months children in pastoral community of Korahay Zone, Somali Regional State, Ethiopia, 2016. Methods: Community based cross sectional study design was done among 770 children in pastoral community of Korahay Zone. Systematic sampling techniques were used to select households and took child mother pair from each selected households. Data was collected using pre-tested and structured questionnaire. Odds ratio with 95% confidence interval was used to assess level of significance. Result: Prevalence of stunting among 6-59 months age children was 31.9%. Sex (AOR: 1.47, 95%CI 1.02, 2.11), age (AOR: 2.10, 95%CI 1.16, 3.80), maternal education (AOR: 3.42, 95%CI 1.58, 7.41), maternal occupation (AOR: 3.10, 95%CI 1.85, 5.19), monthly income (AOR: 1.47, 95%CI 1.03, 2.09), PNC visits (AOR: 1.59, 95%CI 1.07, 2.37), source of water (AOR: 3.41, 95%CI 1.96, 5.93), toilet availability (AOR: 1.71, 95%CI 1.13, 2.58), first milk feeding (AOR: 3.37, 95%CI 2.27, 5.02) and bottle feeding (AOR: 2.07, 95%CI 1.34, 3.18) were significant predictors of stunting. Conclusion and recommendations: Prevalence of stunting among 6-59 months children was high 31.9%. Lack maternal education, not feeding first milk, unsafe water supply, absence toilet availability and bottle feeding can increase the risk of stunting. So, educating mothers on child feeding practice, sanitation and important of first milk can reduce stunting.

Keywords: dietary, environmental, healthcare, socio-demographic, stunting

Procedia PDF Downloads 544

Authors: Zhou BingHai, Fradet Victor

Abstract:

Lean philosophy follows the simple principle of “creating more value with fewer resources”. In accordance with this policy, material handling can be managed by the mean of Kanban which by triggering every feeding tour only when needed regulates the flow of material in one of the most efficient way. This paper focuses on Kanban Supermarket’s parameters and their optimization on a purely cost-based point of view. Number and size of forklifts, as well as size of the containers they carry, will be variables of the cost function which includes handling costs, inventory costs but also shortage costs. With an innovative computational approach encoded into industrial engineering software Tecnomatix and reproducing real-life conditions, a fictive assembly line is established and produces a random list of orders. Multi-scenarios are then run to study the impact of each change of parameter and the variation of costs it implies. Lastly, best-case scenarios financially speaking are selected.

Keywords: Kanban, supermarket, parts-feeding policies, multi-scenario simulation, assembly line

Procedia PDF Downloads 170

Authors: Nicole Banton

Abstract:

The maternal and infant mortality rate of Blacks is three times that of Whites in the US. Research indicates that breastfeeding lowers both. In this paper, the researcher examines how the ideas that Black/African American mothers had about breastfeeding before, during, and after pregnancy (postpartum) affected whether or not they initiated breastfeeding. The researcher used snowball sampling to recruit thirty African-American mothers from the Orlando area. At the time of her interview, each mother had at least one child who was at least three years old. Through in-depth face-to-face interviews, the researcher investigated how mothers’ healthcare providers affected their decision-making about infant feeding, as well as how the type of birth that she had (e.g., preterm, vaginal, c-section, full term) affected her actual versus idealized infant feeding practice. Through our discussions, we explored how pre-pregnancy perceptions, birth and postpartum experiences, social support, and the discourses surrounding motherhood within an African-American context affected the perceptions and experiences that the mothers in the study had with their infant feeding practice(s). Findings suggest that the pregnancy and birth experiences of the mothers in the study influenced whether or not they breastfed exclusively, combined breastfeeding and infant formula use, or used infant formula exclusively. Specifically, the interplay of invocation of agency (the ability to control their bodies before, during, and after birth), birth outcomes, and the interaction that the mothers in this study had with resources, human and material, had the highest impact on the initiation, duration, and attitude toward breastfeeding.

Keywords: African American mothers, maternal health, breastfeeding, birth, midwives, obstetricians, hospital birth, breast pumps, formula use, infant feeding, lactation consultant, postpartum, vaginal birth, c-section, familial support, social support, work, pregnancy

Procedia PDF Downloads 42

Authors: M. A. Akhavan-Behabadi, M. Najafi, A. Abbasi

Abstract:

An empirical investigation was performed in order to study the heat transfer characteristics of R600a flow boiling inside horizontal flattened tubes and the simultaneous effect of nanoparticles on boiling heat transfer in flattened channel. Round copper tubes of 8.7 mm I.D. were deformed into flattened shapes with different inside heights of 6.9, 5.5, and 3.4 mm as test areas. The effect of different parameters such as mass flux, vapor quality and inside height on heat transfer coefficient was studied. Flattening the tube caused significant enhancement in heat transfer performance so that the maximum augmentation ratio of 163% was obtained in flattened channel with lowest internal height. A new correlation was developed based on the present experimental data to predict the heat transfer coefficient in flattened tubes. This correlation estimated 90% of the entire database within ±20%.

Keywords: nano particles, flattend tube, R600a, CuO

Procedia PDF Downloads 294

Authors: Syukri Himran, Rustan Taraka, Anto Duma

Abstract:

The aim of the study is to improve the understanding of latent and sensible thermal energy storage within a paraffin wax media by an array of cylindrical tubes arranged both in in-line and staggered layouts. An analytical and experimental study was carried out in a horizontal shell-and-tube type system during the melting process. Pertamina paraffin-wax was used as a phase change material (PCM), where as the tubes are embedded in the PCM. From analytical study we can obtain the useful information in designing a thermal energy storage such as : the motion of interface, amount of material melted at any time in the process, and the heat storage characteristic during melting. The use of staggered tubes is proposed as superior to in-line layout for thermal storage. The experimental study was used to verify the validity of the analytical predictions. From the comparisons, the analytical and experimental data are in a good agreement.

Keywords: latent, sensible, paraffin-wax, thermal energy storage, conduction, natural convection

Procedia PDF Downloads 539