Search results for: small helicopters
3877 Optimized Electron Diffraction Detection and Data Acquisition in Diffraction Tomography: A Complete Solution by Gatan
Authors: Saleh Gorji, Sahil Gulati, Ana Pakzad
Abstract:
Continuous electron diffraction tomography, also known as microcrystal electron diffraction (MicroED) or three-dimensional electron diffraction (3DED), is a powerful technique, which in combination with cryo-electron microscopy (cryo-ED), can provide atomic-scale 3D information about the crystal structure and composition of different classes of crystalline materials such as proteins, peptides, and small molecules. Unlike the well-established X-ray crystallography method, 3DED does not require large single crystals and can collect accurate electron diffraction data from crystals as small as 50 – 100 nm. This is a critical advantage as growing larger crystals, as required by X-ray crystallography methods, is often very difficult, time-consuming, and expensive. In most cases, specimens studied via 3DED method are electron beam sensitive, which means there is a limitation on the maximum amount of electron dose one can use to collect the required data for a high-resolution structure determination. Therefore, collecting data using a conventional scintillator-based fiber coupled camera brings additional challenges. This is because of the inherent noise introduced during the electron-to-photon conversion in the scintillator and transfer of light via the fibers to the sensor, which results in a poor signal-to-noise ratio and requires a relatively higher and commonly specimen-damaging electron dose rates, especially for protein crystals. As in other cryo-EM techniques, damage to the specimen can be mitigated if a direct detection camera is used which provides a high signal-to-noise ratio at low electron doses. In this work, we have used two classes of such detectors from Gatan, namely the K3® camera (a monolithic active pixel sensor) and Stela™ (that utilizes DECTRIS hybrid-pixel technology), to address this problem. The K3 is an electron counting detector optimized for low-dose applications (like structural biology cryo-EM), and Stela is also a counting electron detector but optimized for diffraction applications with high speed and high dynamic range. Lastly, data collection workflows, including crystal screening, microscope optics setup (for imaging and diffraction), stage height adjustment at each crystal position, and tomogram acquisition, can be one of the other challenges of the 3DED technique. Traditionally this has been all done manually or in a partly automated fashion using open-source software and scripting, requiring long hours on the microscope (extra cost) and extensive user interaction with the system. We have recently introduced Latitude® D in DigitalMicrograph® software, which is compatible with all pre- and post-energy-filter Gatan cameras and enables 3DED data acquisition in an automated and optimized fashion. Higher quality 3DED data enables structure determination with higher confidence, while automated workflows allow these to be completed considerably faster than before. Using multiple examples, this work will demonstrate how to direct detection electron counting cameras enhance 3DED results (3 to better than 1 Angstrom) for protein and small molecule structure determination. We will also show how Latitude D software facilitates collecting such data in an integrated and fully automated user interface.Keywords: continuous electron diffraction tomography, direct detection, diffraction, Latitude D, Digitalmicrograph, proteins, small molecules
Procedia PDF Downloads 953876 Influence of Preparation, Characterisation and Application of Carbon Nano Tube
Authors: Dhaivat S. Soni, Snehal Thakor, Afroz Bhatti
Abstract:
The prepare CNTs in bulk quantity by as easiest as possible method with highly pure and small diameter. Prepared CNTs first charactered its structural parameter for the conformation of CNTs and purity. Surface morphology of CNTs stured by using various instruments finally study application of prepared CNTs in various field. Carbon nanotubes (CNTs) were synthesized in large scale by pyrolyzing activated carbon in sealed autoclaves.Keywords: nanostructures, nanotubes, carbon, pyrolysis
Procedia PDF Downloads 3873875 Probabilistic Graphical Model for the Web
Authors: M. Nekri, A. Khelladi
Abstract:
The world wide web network is a network with a complex topology, the main properties of which are the distribution of degrees in power law, A low clustering coefficient and a weak average distance. Modeling the web as a graph allows locating the information in little time and consequently offering a help in the construction of the research engine. Here, we present a model based on the already existing probabilistic graphs with all the aforesaid characteristics. This work will consist in studying the web in order to know its structuring thus it will enable us to modelize it more easily and propose a possible algorithm for its exploration.Keywords: clustering coefficient, preferential attachment, small world, web community
Procedia PDF Downloads 2673874 Biochar and Food Security in Central Uganda
Authors: Nataliya Apanovich, Mark Wright
Abstract:
Uganda is among the poorest but fastest growing populations in the world. Its annual population growth of 3% puts additional stress through land fragmentation, agricultural intensification, and deforestation on already highly weathered tropical (Ferralsol) soils. All of these factors lead to decreased agricultural yields and consequently diminished food security. The central region of Uganda, Buganda Kingdom, is especially vulnerable in terms of food security as its high population density coupled with mismanagement of natural resources led to gradual loss of its soil and even changes in microclimate. These changes are negatively affecting livelihoods of smallholder farmers who comprise 80% of all population in Uganda. This research focuses on biochar for soil remediation in Masaka District, Uganda. If produced on a small scale from locally sourced materials, biochar can increase the quality of soil in a cost and time effective manner. To assess biochar potential, 151 smallholder farmers were interviewed on the types of crops grown, agricultural residues produced and their use, as well as on attitudes towards biochar use and its production on a small scale. The interviews were conducted in 7 sub-counties, 32 parishes, and 92 villages. The total farmland covered by the study was 606.2 kilometers. Additional information on the state of agricultural development and environmental degradation in the district was solicited from four local government officials via informal interviews. This project has been conducted in collaboration with the international agricultural research institution, Makerere University in Kampala, Uganda. The results of this research can have implications on the way farmers perceive the value of their agricultural residues and what they decide to do with them. The underlying objective is to help smallholders in degraded soils increase their agricultural yields through the use of biochar without diverting the already established uses of agricultural residues to a new soil management practice.Keywords: agricultural residues, biochar, central Uganda, food security, soil erosion, soil remediation
Procedia PDF Downloads 2753873 Climate Change, Multiple Stressors, and Livelihoods: A Search for Communities Understanding, Vulnerability, and Adaptation in Zanzibar Islands
Authors: Thani R. Said
Abstract:
There is a wide concern on the academic literatures that the world is on course to experience “severe and pervasive” negative impacts from climate change unless it takes rapid action to slash its greenhouse gas emissions. The big threat however, is more belligerent in the third world countries, small islands states in particular. Most of the academic literatures claims that the livelihoods, economic and ecological landscapes of most of the coastal communities are into serious danger due to the peril of climate change. However, focusing the climate change alone and paying less intention to the surrounding stressors which sometimes are apparent then the climate change its self has now placed at the greater concern on academic debates. The recently studies have begun to question such narrowed assessment of climate change intervening programs from both its methodological and theoretical perspectives as related with livelihoods and the landscapes of the coastal communities. Looking climate as alone as an ostentatious threat doesn't yield the yield an appropriate mechanisms to address the problem in its totality and tend to provide the partially picture of the real problem striking the majority of the peoples living in the coastal areas of small islands states, Zanzibar in particular. By using the multiples human grounded knowledge approaches, the objective of this study is to go beyond the mere climate change by analyzing other multiples stressors that real challenging and treating the livelihoods, economic and ecological landscapes of the coastal communities through dialectic understanding, vulnerability and adaptive mechanisms at their own localities. To be more focus and to capture the full picture on this study special intention will be given to those areas were climate changes intervening programs have been onto place, the study will further compare and contrast between the two islands communities, Unguja and Pemba taking into account their respective diverse economic and geographical landscapes prevailed.Keywords: climate change, multiple stressors, livelihoods, vulnerability-adaptation
Procedia PDF Downloads 3943872 Exploration of Environmental Parameters on the Evolution of Vernacular Building Techniques in East Austria
Authors: Hubert Feiglstorfer
Abstract:
Due to its location in a transition zone from the Pannonian to the pre-Alpine region, the east of Austria shows a small-scale diversity in the regional development of certain vernacular building techniques. In this article the relationship between natural building material resources, topography and climate will be examined. Besides environmental preconditions, social and economic historical factors have developed different construction techniques within certain regions in the Weinviertel and Burgenland, the two eastern federal states of Austria. But even within these regions, varying building techniques were found, due to the locally different use of raw materials like wood, stone, clay, lime, or organic fibres. Within these small-scale regions, building traditions were adapted over the course of time due to changes in the use of the building material, for example from wood to brick or from wood to earth. The processing of the raw materials varies from region to region, for example as rammed earth, cob, log, or brick construction. Environmental preconditions cross national borders. For that reason, developments in the neighbouring countries, the Czech Republic, Slovakia, Hungary and Slovenia are included in this analysis. As an outcome of this research a map was drawn which shows the interrelation between locally available building materials, topography, climate and local building techniques? As a result of this study, which covers the last 300 years, one can see how the local population used natural resources very sensitively adapted to local environmental preconditions. In the case of clay, for example, changes of proportions of lime and particular minerals cause structural changes that differ from region to region. Based on material analyses in the field of clay mineralogy, on ethnographic research, literature and archive research, explanations for certain local structural developments will be given for the first time over the region of East Austria.Keywords: European crafts, material culture, architectural history, earthen architecture, earth building history
Procedia PDF Downloads 2283871 Human–Wildlife Conflicts in Selected Areas of Azad Jammu and Kashmir, Pakistan
Authors: Nausheen Irshad
Abstract:
Human-wildlife conflict (HWC) exists in both developed and developing countries though it is more serious in developing nations. Knowledge of species ecology and species sensitivity to anthropogenic pressures is an important prerequisite for conservation/management. Therefore, three districts (Poonch, Bagh, and Muzaffarabad) of Azad Jammu and Kashmir were selected to highlight the wildlife hunting practices from January 2015 to November 2018. The study area was thoroughly explored to recover dead animals. Moreover, the local community was investigated (questionnaire survey) to catch on motives of killing. The results showed HWC mainly arises due to feeding habits of wild animals as some are frugivorous (small Indian civet and small Kashmir flying squirrel) who damaged human cultivated fruit trees. Besides, Indian crested porcupine and wild boar act as serious crop pests. The feeding upon domestic animals (common leopard) and poultry (Asiatic Jackal and Red fox) were also reported as factors of conflict. Hence numerous wild animals and birds (N=120) were found killed by natives in revenge. Despite protected status in Pakistan, the killed mammals belonged to categories of critically endangered (Panthera pardus) and near threatened (Viverricula indica) species. The important birds include critically endangered (Falco peregrines) and endangered (Lophura leucomelanos) species. It was found that mammals were primarily killed due to HWC (60%) followed by recreation (20%) and trade (15%) Whereas, the foremost hunting reasons for birds are recreation (50%), food (25%) and trade (25%). The drastic hunting/killing of the species needs our immediate attention. This unwarranted killing must be stopped forthwith otherwise these animals become extinct.Keywords: Azad Jammu and Kashmir, anthropogenic pressures, endangered species, human-wildlife conflicts
Procedia PDF Downloads 1553870 Phytolith Analysis of Intrabasaltic Palaeosols (Bole Beds) from the Deccan Volcanic Province of Western India: A Preliminary Study
Authors: Sayyed Mohammed Rafi
Abstract:
Phytolith studies were carried out for the intrabasaltic bole beds occurring in the western part of the Deccan Volcanic Province. This preliminary study indicates the presence of multiform phytoliths both in red and green boles. Red bole indicates well preserved elongate phytoliths from Acanthaceae plants while bulky Bulliform phytoliths mainly from Pleioblastus/ Andropogonea/reeds plants. Degeneration of few phytoliths from red bole indicates either leaching/etching or some other activity that is responsible for such post-preservation conditions. Phytoliths from the green bole, however, seem to be well preserved as compared to those from the red bole. The phytoliths from green bole are mainly of Festucoid types (especially small square and rectangular types) indicating the presence of Chrysobalanaceae type of vegetation followed by elongate phytoliths from Acanthaceae plant types. The Multiform Trichomes seems to be derived from Panicoid/Andropogonoid/Burseraceae/Fabaceae while Bulliforms from Pleioblastus/Andropogonea/reeds. Presences of silicified woody elements from both red and green boles indicate the presence of dicotyledonous plants which could have been in the form of small shrubs. The degenerated phytoliths in red bole suggest leaching/etching or higher intensity of weathering suggesting the existence of well-drained conditions during its formation that enhanced the leaching activity while the presence of well-preserved phytoliths in green bole point towards the existence of damp and desiccated conditions during its formation. The prevalence of dry condition during red bole formation could suggest their formation under higher temperature as compared to green bole. Based on the phytolith analysis it is too early to comment on the palaeoclimates which could have prevailed during the bole bed formations. However a detailed micromorphological, as well as phytolith analysis of more samples, can throw light on the palaeoenvironmental conditions as well as the biological activity during their formation.Keywords: Deccan volcanic province, intrabasaltic bole beds, palaeoclimate, phytoliths
Procedia PDF Downloads 2353869 Sensory Interventions for Dementia: A Review
Authors: Leigh G. Hayden, Susan E. Shepley, Cristina Passarelli, William Tingo
Abstract:
Introduction: Sensory interventions are popular therapeutic and recreational approaches for people living with all stages of dementia. However, it is unknown which sensory interventions are used to achieve which outcomes across all subtypes of dementia. Methods: To address this gap, we conducted a scoping review of sensory interventions for people living with dementia. We conducted a search of the literature for any article published in English from 1 January 1990 to 1 June 2019, on any sensory or multisensory intervention targeted to people living with any kind of dementia, which reported on patient health outcomes. We did not include complex interventions where only a small aspect was related to sensory stimulation. We searched the databases Medline, CINHAL, and Psych Articles using our institutional discovery layer. We conducted all screening in duplicate to reduce Type 1 and Type 2 errors. The data from all included papers were extracted by one team member, and audited by another, to ensure consistency of extraction and completeness of data. Results: Our initial search captured 7654 articles, and the removal of duplicates (n=5329), those that didn’t pass title and abstract screening (n=1840) and those that didn’t pass full-text screening (n=281) resulted in 174 articles included. The countries with the highest publication in this area were the United States (n=59), the United Kingdom (n=26) and Australia (n=15). The most common type of interventions were music therapy (n=36), multisensory rooms (n=27) and multisensory therapies (n=25). Seven articles were published in the 1990’s, 55 in the 2000’s, and the remainder since 2010 (n=112). Discussion: Multisensory rooms have been present in the literature since the early 1990’s. However, more recently, nature/garden therapy, art therapy, and light therapy have emerged since 2008 in the literature, an indication of the increasingly diverse scholarship in the area. The least popular type of intervention is a traditional food intervention. Taste as a sensory intervention is generally avoided for safety reasons, however it shows potential for increasing quality of life. Agitation, behavior, and mood are common outcomes for all sensory interventions. However, light therapy commonly targets sleep. The majority (n=110) of studies have very small sample sizes (n=20 or less), an indicator of the lack of robust data in the field. Additional small-scale studies of the known sensory interventions will likely do little to advance the field. However, there is a need for multi-armed studies which directly compare sensory interventions, and more studies which investigate the use of layering sensory interventions (for example, adding an aromatherapy component to a lighting intervention). In addition, large scale studies which enroll people at early stages of dementia will help us better understand the potential of sensory and multisensory interventions to slow the progression of the disease.Keywords: sensory interventions, dementia, scoping review
Procedia PDF Downloads 1243868 The Effect of Traffic Load on the Maximum Response of a Cable-Stayed Bridge under Blast Loads
Authors: S. K. Hashemi, M. A. Bradford, H. R. Valipour
Abstract:
The Recent collapse of bridges has raised the awareness about safety and robustness of bridges subjected to extreme loading scenarios such as intentional/unintentional blast loads. The air blast generated by the explosion of bombs or fuel tankers leads to high-magnitude short-duration loading scenarios that can cause severe structural damage and loss of critical structural members. Hence, more attentions need to put towards bridge structures to develop guidelines to increase the resistance of such structures against the probable blast. Recent advancements in numerical methods have brought about the viable and cost effective facilities to simulate complicated blast scenarios and subsequently provide useful reference for safeguarding design of critical infrastructures. In the previous studies common bridge responses to blast load, the traffic load is sometimes not included in the analysis. Including traffic load will increase the axial compression in bridge piers especially when the axial load is relatively small. Traffic load also can reduce the uplift of girders and deck when the bridge experiences under deck explosion. For more complicated structures like cable-stayed or suspension bridges, however, the effect of traffic loads can be completely different. The tension in the cables increase and progressive collapse is likely to happen while traffic loads exist. Accordingly, this study is an attempt to simulate the effect of traffic load cases on the maximum local and global response of an entire cable-stayed bridge subjected to blast loadings using LS-DYNA explicit finite element code. The blast loads ranged from small to large explosion placed at different positions above the deck. Furthermore, the variation of the traffic load factor in the load combination and its effect on the dynamic response of the bridge under blast load is investigated.Keywords: blast, cable-stayed bridge, LS-DYNA, numerical, traffic load
Procedia PDF Downloads 3253867 A Technical-Economical Study of a New Solar Tray Distillator
Authors: Abderrahmane Diaf, Assia Cherfa, Lamia Karadaniz
Abstract:
Multiple tray solar distillation offers an interesting alternative for small-scale desalination and production high quality distilled water at a competitive cost using solar energy. In this work, we present indoor/outdoor trial performance data of our multiple tray solar distillation as well as the results of cost estimation analysis.Keywords: solar desalination, tray distillation, multi-étages solaire, solar distillation
Procedia PDF Downloads 4163866 Dynamics of Soil Fertility Management in India: An Empirical Analysis
Authors: B. Suresh Reddy
Abstract:
The over dependence on chemical fertilizers for nutrient management in crop production for the last few decades has led to several problems affecting soil health, environment and farmers themselves. Based on the field work done in 2012-13 with 1080 farmers of different size-classes in semi-arid regions of Uttar Pradesh, Jharkhand and Madhya Pradesh states of India, this paper reveals that the farmers in semi-arid regions of India are actively managing soil fertility and other soil properties through a wide range of practices that are based on local resources and knowledge. It also highlights the socio-economic web woven around these soil fertility management practices. This study highlights the contribution of organic matter by traditional soil fertility management practices in maintaining the soil health. Livestock has profound influence on the soil fertility enhancement through supply of organic manure. Empirical data of this study has clearly revealed how farmers’ soil fertility management options are being undermined by government policies that give more priority to chemical fertiliser-based strategies. Based on the findings it is argued that there should be a 'level playing field' for both organic and inorganic soil fertility management methods by promoting and supporting farmers in using organic methods. There is a need to provide credit to farmers for adopting his choice of soil fertility management methods which suits his socio-economic conditions and that best suits the long term productivity of soils. The study suggests that the government policies related to soil fertility management must be enabling, creating the conditions for development based more on locally available resources and local skills and knowledge. This will not only keep Indian soils in healthy condition but also support the livelihoods of millions of people, especially the small and marginal farmers.Keywords: livestock, organic matter, small farmers, soil fertility
Procedia PDF Downloads 1683865 Economic Assessment of the Fish Solar Tent Dryers
Authors: Collen Kawiya
Abstract:
In an effort of reducing post-harvest losses and improving the supply of quality fish products in Malawi, the fish solar tent dryers have been designed in the southern part of Lake Malawi for processing small fish species under the project of Cultivate Africa’s Future (CultiAF). This study was done to promote the adoption of the fish solar tent dryers by the many small scale fish processors in Malawi through the assessment of the economic viability of these dryers. With the use of the project’s baseline survey data, a business model for a constructed ‘ready for use’ solar tent dryer was developed where investment appraisal techniques were calculated in addition with the sensitivity analysis. The study also conducted a risk analysis through the use of the Monte Carlo simulation technique and a probabilistic net present value was found. The investment appraisal results showed that the net present value was US$8,756.85, the internal rate of return was 62% higher than the 16.32% cost of capital and the payback period was 1.64 years. The sensitivity analysis results showed that only two input variables influenced the fish solar dryer investment’s net present value. These are the dried fish selling prices that were correlating positively with the net present value and the fresh fish buying prices that were negatively correlating with the net present value. Risk analysis results showed that the chances that fish processors will make a loss from this type of investment are 17.56%. It was also observed that there exist only a 0.20 probability of experiencing a negative net present value from this type of investment. Lastly, the study found that the net present value of the fish solar tent dryer’s investment is still robust in spite of any changes in the levels of investors risk preferences. With these results, it is concluded that the fish solar tent dryers in Malawi are an economically viable investment because they are able to improve the returns in the fish processing activity. As such, fish processors need to adopt them by investing their money to construct and use them.Keywords: investment appraisal, risk analysis, sensitivity analysis, solar tent drying
Procedia PDF Downloads 2653864 Non-Native and Invasive Fish Species in Poland
Authors: Tomasz Raczyński
Abstract:
Non-native and invasive species negatively transform ecosystems. Non-native fish species can displace native fish species through competition, predation, disrupting spawning, transforming ecosystems, or transmitting parasites. This influence is more and more noticeable in Poland and in the world. From December 2014 to October 2020, did catch of fishes by electrofishing method carried on 416 sites in various parts of Poland. Research was conducted in both running and stagnant freshwaters with the predominance of running waters. Only sites where the presence of fish was found were analysed. The research covered a wide spectrum of waters from small mountain streams, through drainage ditches to the largest Polish river - the Vistula. Single sites covered oxbow lakes, small ponds and lakes. Electrofishing was associated with ichthyofauna inventories and was mainly aimed at detecting protected species of fish and lampreys or included in the annexes to the EU Habitats Directive (Council Directive 92/43/EEC on the Conservation of natural habitats and of wild fauna and flora). The results of these catches were analysed for alien and invasive fish species. The analysis of the catch structure shows that in 71 out of 416 research sites was found alien and invasive fish species, belonging to 9 taxa. According to the above, alien species of fish are present in 17% of the study sites. The most frequently observed species was the Prussian carp Carassius gibelio, which was recorded on 43 sites. Stone moroko Pseudorasbora parva was found on 24 sites. Chinese sleeper Perccottus glenii was found on 6 sites, and Bullhead Ameiurus sp. was also found on 6 sites. Western tubenose goby Proterorhinus semilunaris was found at 5 sites and Rainbow trout Oncorhynchus mykiss at 3 sites. Monkey goby Neogobius fluviatilis, Round goby Neogobius melanostomus and Eurasian carp Cyprinus carpio was recorded on 2 sites.Keywords: non-native species, invasive species, fish species, invasive fish species, native fish species
Procedia PDF Downloads 1023863 The Study of Heat and Mass Transfer for Ferrous Materials' Filtration Drying
Authors: Dmytro Symak
Abstract:
Drying is a complex technologic, thermal and energy process. Energy cost of drying processes in many cases is the most costly stage of production, and can be over 50% of total costs. As we know, in Ukraine over 85% of Portland cement is produced moist, and the finished product energy costs make up to almost 60%. During the wet cement production, energy costs make up over 5500 kJ / kg of clinker, while during the dry only 3100 kJ / kg, that is, switching to a dry Portland cement will allow result into double cutting energy costs. Therefore, to study raw materials drying process in the manufacture of Portland cement is very actual task. The fine ferrous materials drying (small pyrites, red mud, clay Kyoko) is recommended to do by filtration method, that is one of the most intense. The essence of filtration method drying lies in heat agent filtering through a stationary layer of wet material, which is located on the perforated partition, in the "layer-dispersed material - perforated partition." For the optimum drying purposes, it is necessary to establish the dependence of pressure loss in the layer of dispersed material, and the values of heat and mass transfer, depending on the speed of the gas flow filtering. In our research, the experimentally determined pressure loss in the layer of dispersed material was generalized based on dimensionless complexes in the form and coefficients of heat exchange. We also determined the relation between the coefficients of mass and heat transfer. As a result of theoretic and experimental investigations, it was possible to develop a methodology for calculating the optimal parameters for the thermal agent and the main parameters for the filtration drying installation. The comparison of calculated by known operating expenses methods for the process of small pyrites drying in a rotating drum and filtration method shows to save up to 618 kWh per 1,000 kg of dry material and 700 kWh during filtration drying clay.Keywords: drying, cement, heat and mass transfer, filtration method
Procedia PDF Downloads 2533862 Effect of Climate Change on Aridity Index in South Bihar
Authors: Aayush Anant, Roshni Thendiyath
Abstract:
Aridity impacts on agriculture, as well as ecological, human health, and economic activities. In the present study, the effect of climate change on aridity index has been analysed in South Bihar for the past 30 year period by five types of aridity indices as Lang AI, De-Martonne AI, Erinc AI, Pinna combinative AI and UNEP AI. For the study of aridity index, the analysis of rainfall and temperature is significant. Rainfall was analysed for 30 year period from data of 23 gridded stations in for the period 1991-2020. The results show that rainfall pattern was decreasing with respect to previous decades for majority of stations. Trend of maximum, minimum and mean annual temperature has been observed, which shows increasing trend. Structural breakpoint was observed for mean annual temperature data series in year 2004. In period 1991-2004 mean annual temperature was 25.25 ºC, and in period 2005-2020, mean annual temperature was 25.7 ºC. Average aridity index has been calculated by all the above mentioned methods for whole 30 period. Lang AI shows that eastern part of study area is Humid type, and rest all is semi arid. De-Martonne AI also reveals that east part is humid, but rest of the study area is moist sub humid. According to Erinc AI and Pinna, combinative AI shows that whole south Bihar is dry sub humid and semi dry, respectively. UNEP AI shows most of the part as sub humid, and very small part in west is semi arid, while small part of east is humid. Temporal distribution of all the aridity indices shows a decreasing trend. This indicates a decrease in the humid areas in south Bihar for the selected time period.Keywords: drought, aridity index, climate change, rainfall, temperature
Procedia PDF Downloads 723861 Adverse Curing Conditions and Performance of Concrete: Bangladesh Perspective
Authors: T. Manzur
Abstract:
Concrete is the predominant construction material in Bangladesh. In large projects, stringent quality control procedures are usually followed under the supervision of experienced engineers and skilled labors. However, in the case of small projects and particularly at distant locations from major cities, proper quality control is often an issue. It has been found from experience that such quality related issues mainly arise from inappropriate proportioning of concrete mixes and improper curing conditions. In most cases external curing method is followed which requires supply of adequate quantity of water along with proper protection against evaporation. Often these conditions are found missing in the general construction sites and eventually lead to production of weaker concrete both in terms of strength and durability. In this study, an attempt has been made to investigate the performance of general concreting works of the country when subjected to several adverse curing conditions that are quite common in various small to medium construction sites. A total of six different types of adverse curing conditions were simulated in the laboratory and samples were kept under those conditions for several days. A set of samples was also submerged in normal curing condition having proper supply of curing water. Performance of concrete was evaluated in terms of compressive strength, tensile strength, chloride permeability and drying shrinkage. About 37% and 25% reduction in 28-day compressive and tensile strength were observed respectively, for samples subjected to most adverse curing condition as compared to the samples under normal curing conditions. Normal curing concrete exhibited moderate permeability (close to low permeability) whereas concrete under adverse curing conditions showed very high permeability values. Similar results were also obtained for shrinkage tests. This study, thus, will assist concerned engineers and supervisors to understand the importance of quality assurance during the curing period of concrete.Keywords: adverse, concrete, curing, compressive strength, drying shrinkage, permeability, tensile strength
Procedia PDF Downloads 1893860 Influence of Thermal Annealing on Phase Composition and Structure of Quartz-Sericite Minerale
Authors: Atabaev I. G., Fayziev Sh. A., Irmatova Sh. K.
Abstract:
Raw materials with high content of Kalium oxide widely used in ceramic technology for prevention or decreasing of deformation of ceramic goods during drying process and under thermal annealing. Becouse to low melting temperature it is also used to decreasing of the temperature of thermal annealing during fabrication of ceramic goods [1,2]. So called “Porceline or China stones” - quartz-sericite (muscovite) minerals is also can be used for prevention of deformation as the content of Kalium oxide in muscovite is rather high (SiO2, + KAl2[AlSi3O10](OH)2). [3] . To estimation of possibility of use of this mineral for ceramic manufacture, in the presented article the influence of thermal processing on phase and a chemical content of this raw material is investigated. As well as to other ceramic raw materials (kaoline, white burning clays) the basic requirements of the industry to quality of "a porcelain stone» are following: small size of particles, relative high uniformity of disrtribution of components and phase, white color after burning, small content of colorant oxides or chromophores (Fe2O3, FeO, TiO2, etc) [4,5]. In the presented work natural minerale from the Boynaksay deposit (Uzbekistan) is investigated. The samples was mechanically polished for investigation by Scanning Electron Microscope. Powder with size of particle up to 63 μm was used to X-ray diffractometry and chemical analysis. The annealing of samples was performed at 900, 1120, 1350oC during 1 hour. Chemical composition of Boynaksay raw material according to chemical analysis presented in the table 1. For comparison the composition of raw materials from Russia and USA are also presented. In the Boynaksay quartz – sericite the average parity of quartz and sericite makes 55-60 and 30-35 % accordingly. The distribution of quartz and sericite phases in raw material was investigated using electron probe scanning electronic microscope «JEOL» JXA-8800R. In the figure 1 the scanning electron microscope (SEM) micrograps of the surface and the distributions of Al, Si and K atoms in the sample are presented. As it seen small granular, white and dense mineral includes quartz, sericite and small content of impurity minerals. Basically, crystals of quartz have the sizes from 80 up to 500 μm. Between quartz crystals the sericite inclusions having a tablet form with radiant structure are located. The size of sericite crystals is ~ 40-250 μm. Using data on interplanar distance [6,7] and ASTM Powder X-ray Diffraction Data it is shown that natural «a porcelain stone» quartz – sericite consists the quartz SiO2, sericite (muscovite type) KAl2[AlSi3O10](OH)2 and kaolinite Al203SiO22Н2О (See Figure 2 and Table 2). As it seen in the figure 3 and table 3a after annealing at 900oC the quartz – sericite contains quartz – SiO2 and muscovite - KAl2[AlSi3O10](OH)2, the peaks related with Kaolinite are absent. After annealing at 1120oC the full disintegration of muscovite and formation of mullite phase Al203 SiO2 is observed (the weak peaks of mullite appears in fig 3b and table 3b). After annealing at 1350oC the samples contains crystal phase of quartz and mullite (figure 3c and table 3с). Well known Mullite gives to ceramics high density, abrasive and chemical stability. Thus the obtained experimental data on formation of various phases during thermal annealing can be used for development of fabrication technology of advanced materials. Conclusion: The influence of thermal annealing in the interval 900-1350oC on phase composition and structure of quartz-sericite minerale is investigated. It is shown that during annealing the phase content of raw material is changed. After annealing at 1350oC the samples contains crystal phase of quartz and mullite (which gives gives to ceramics high density, abrasive and chemical stability).Keywords: quartz-sericite, kaolinite, mullite, thermal processing
Procedia PDF Downloads 4063859 Multiple Organ Manifestation in Neonatal Lupus Erythematous: Report of Two Cases
Authors: A. Lubis, R. Widayanti, Z. Hikmah, A. Endaryanto, A. Harsono, A. Harianto, R. Etika, D. K. Handayani, M. Sampurna
Abstract:
Neonatal lupus erythematous (NLE) is a rare disease marked by clinical characteristic and specific maternal autoantibody. Many cutaneous, cardiac, liver, and hematological manifestations could happen with affect of one organ or multiple. In this case, both babies were premature, low birth weight (LBW), small for gestational age (SGA) and born through caesarean section from a systemic lupus erythematous (SLE) mother. In the first case, we found a baby girl with dyspnea and grunting. Chest X ray showed respiratory distress syndrome (RDS) great I and echocardiography showed small atrial septal defect (ASD) and ventricular septal defect (VSD). She also developed anemia, thrombocytopenia, elevated C-reactive protein, hypoalbuminemia, increasing coagulation factors, hyperbilirubinemia, and positive blood culture of Klebsiella pneumonia. Anti-Ro/SSA and Anti-nRNP/sm were positive. Intravenous fluid, antibiotic, transfusion of blood, thrombocyte concentrate, and fresh frozen plasma were given. The second baby, male presented with necrotic tissue on the left ear and skin rashes, erythematous macula, athropic scarring, hyperpigmentation on all of his body with various size and facial haemorrhage. He also suffered from thrombocytopenia, mild elevated transaminase enzyme, hyperbilirubinemia, anti-Ro/SSA was positive. Intravenous fluid, methyprednisolone, intravenous immunoglobulin (IVIG), blood, and thrombocyte concentrate transfution were given. Two cases of neonatal lupus erythematous had been presented. Diagnosis based on clinical presentation and maternal auto antibody on neonate. Organ involvement in NLE can occur as single or multiple manifestations.Keywords: neonatus lupus erythematous, maternal autoantibody, clinical characteristic, multiple organ manifestation
Procedia PDF Downloads 4123858 Aspirin Loaded Poly-L-Lactic Acid Nanofibers and Their Potentials as Small Diameter Vascular Grafts
Authors: Mahboubeh Kabiri, Saba Aslani
Abstract:
Among various approaches used for the treatment of cardiovascular diseases, the occlusion of the small-diameter vascular graft (SDVG) is still an unresolved problem which seeks further research to address them. Though autografts are now the gold standards to be replaced for blocked coronary arteries, they suffer from inadequate quality and quantity. On the other hand, the major problems of the tissue engineered grafts are thrombosis and intimal hyperplasia. Provision of a suitable spatiotemporal release pattern of anticoagulant agents such as heparin and aspirin can be a step forward to overcome such issues . Herein, we fabricated electrospun scaffolds from FDA (Food and Drug Administration) approved poly-L-lactic acid (PLLA) with aspirin loaded into the nanofibers. Also, we surface coated the scaffolds with Amniotic Membrane lysate as a source for natural elastic polymers and a mimic of endothelial basement membrane. The scaffolds were characterized thoroughly structurally and mechanically for their morphology, fiber orientation, tensile strength, hydrophilicity, cytotoxicity, aspirin release and cell attachment support. According to the scanning electron microscopy (SEM) images, the size of fibers ranged from 250 to 500 nm. The scaffolds showed appropriate tensile strength expected for vascular grafts. Cellular attachment, growth, and infiltration were proved using SEM and MTT (3-(4,5-Dimethylthiazol-2-Yl)-2,5-Diphenyltetrazolium Bromide) assay. Drug-loaded scaffolds showed a sustained release profile of aspirin in 7 days. An enhanced cytocompatibility was observed in AM-coated electrospun PLLA fibers compared to uncoated scaffolds. Our results together indicated that AM lysate coated ASA releasing scaffolds have promising potentials for development of a biocompatible SDVG.Keywords: vascular tissue engineering, vascular grafts, anticoagulant agent, aspirin, amniotic membrane
Procedia PDF Downloads 1533857 Legal Problems with the Thai Political Party Establishment
Authors: Paiboon Chuwatthanakij
Abstract:
Each of the countries around the world has different ways of management and many of them depend on people to administrate their country. Thailand, for example, empowers the sovereignty of Thai people under constitution; however, our Thai voting system is not able to flow fast enough under the current Political management system. The sovereignty of Thai people is addressing this problem through representatives during current elections, in order to set a new policy for the countries ideology to change in the House and the Cabinet. This is particularly important in a democracy to be developed under our current political institution. The Organic Act on Political Parties 2007 is the establishment we have today that is causing confrontations within the establishment. There are many political parties that will soon be abolished. Many political parties have already been subsidized. This research study is to analyze the legal problems with the political party establishment under the Organic Act on Political Parties 2007. This will focus on the freedom of each political establishment compared to an effective political operation. Textbooks and academic papers will be referenced from studies home and abroad. The study revealed that Organic Act on Political Parties 2007 has strict provisions on the political structure over the number of members and the number of branches involved within political parties system. Such operations shall be completed within one year; but under the existing laws the small parties are not able to participate with the bigger parties. The cities are capable of fulfilling small political party requirements but fail to become coalesced because the current laws won't allow them to be united as one. It is important to allow all independent political parties to join our current political structure. Board members can’t help the smaller parties to become a large organization under the existing Thai laws. Creating a new establishment that functions efficiently throughout all branches would be one solution to these legal problems between all political parties. With this new operation, individual political parties can participate with the bigger parties during elections. Until current political institutions change their system to accommodate public opinion, these current Thai laws will continue to be a problem with all political parties in Thailand.Keywords: coalesced, political party, sovereignty, elections
Procedia PDF Downloads 3063856 Assessment of Waste Management Practices in Bahrain
Authors: T. Radu, R. Sreenivas, H. Albuflasa, A. Mustafa Khan, W. Aloqab
Abstract:
The Kingdom of Bahrain, a small island country in the Gulf region, is experiencing fast economic growth resulting in a sharp increase in population and greater than ever amounts of waste being produced. However, waste management in the country is still very basic, with landfilling being the most popular option. Recycling is still a scarce practice, with small recycling businesses and initiatives emerging in recent years. This scenario is typical for other countries in the region, with similar amounts of per capita waste being produced. In this paper, we are reviewing current waste management practices in Bahrain by collecting data published by the Government and various authors, and by visiting the country’s only landfill site, Askar. In addition, we have performed a survey of the residents to learn more about the awareness and attitudes towards sustainable waste management strategies. A review of the available data on waste management indicates that the Askar landfill site is nearing its capacity. The site uses open tipping as the method of disposal. The highest percentage of disposed waste comes from the building sector (38.4%), followed by domestic (27.5%) and commercial waste (17.9%). Disposal monitoring and recording are often based on estimates of weight and without proper characterization/classification of received waste. Besides, there is a need for assessment of the environmental impact of the site with systematic monitoring of pollutants in the area and their potential spreading to the surrounding land, groundwater, and air. The results of the survey indicate low awareness of what happens with the collected waste in the country. However, the respondents have shown support for future waste reduction and recycling initiatives. This implies that the education of local communities would be very beneficial for such governmental initiatives, securing greater participation. Raising awareness of issues surrounding recycling and waste management and systematic effort to divert waste from landfills are the first steps towards securing sustainable waste management in the Kingdom of Bahrain.Keywords: landfill, municipal solid waste, survey, waste management
Procedia PDF Downloads 1473855 Sustainable Crop Mechanization among Small Scale Rural Farmers in Nigeria: The Hurdles
Authors: Charles Iledun Oyewole
Abstract:
The daunting challenge that the ‘man with the hoe’ is going to face in the coming decades will be complex and interwoven. With global population already above 7 billion people, it has been estimated that food (crop) production must more than double by 2050 to meet up with the world’s food requirements. Nigeria population is also expected to reach over 240 million people by 2050, at the current annual population growth of 2.61 per cent. The country’s farming population is estimated at over 65 per cent, but the country still depends on food importation to complement production. The small scale farmer, who depends on simple hand tools: hoes and cutlasses, remains the centre of agricultural production, accounting for 90 per cent of the total agricultural output and 80 per cent of the market flow. While the hoe may have been a tool for sustainable development at a time in human history, this role has been smothered by population growth, which has brought too many mouths to be fed (over 170 million), as well as many industries to fuel with raw materials. It may then be argued that the hoe is unfortunately not a tool for the coming challenges and that agricultural mechanization should be the focus. However, agriculture as an enterprise is a ‘complete wheel’ which does not work when broken, particularly, in respect to mechanization. Generally, mechanization will prompt increase production, where land is readily available; increase production, will require post-harvest handling mechanisms, crop processing and subsequent storage. An important aspect of this is readily available and favourable markets for such produce; fuel by good agricultural policies. A break in this wheel will lead to the process of mechanization crashing back to subsistence production, and probably reversal to the hoe. The focus of any agricultural policy should be to chart a course for sustainable mechanization that is environmentally friendly, that may ameliorate Nigeria’s food and raw material gaps. This is the focal point of this article.Keywords: Crop production, Farmer, Hoes, Mechanization, Policy framework, Population, Growth, Rural areas
Procedia PDF Downloads 2083854 Associations between Physical Activity and Risk Factors for Type II Diabetes in Prediabetic Adults
Authors: Rukia Yosuf
Abstract:
Diabetes is a national healthcare crisis related to both macrovascular and microvascular complications. We hypothesized that higher levels of physical activity are associated with lower total and visceral fat mass, lower systolic blood pressure, and increased insulin sensitivity. Participant inclusion criteria: 21-50 years old, BMI ≥ 30 kg/m2, hemoglobin A1C 5.7-6.4, fasting glucose 100-125 mg/dL, and HOMA IR ≥ 2.5. Exclusion criteria: history of diabetes, hypertension, HIV, renal disease, hearing loss, alcoholic intake over four drinks daily, use of organic nitrates or PDE5 inhibitors, and decreased cardiac function. Total physical activity was measured using accelerometers, body composition using DXA, and insulin resistance via fsIVGTT. Clinical and biochemical cardiometabolic risk factors, blood pressure and heart rate were obtained using a calibrated sphygmomanometer. Anthropometric measures, fasting glucose, insulin, lipid profile, C-reactive protein, and BMP were analyzed using standard procedures. Within our study, we found correlations between levels of physical activity in a heterogeneous group of prediabetic adults. Patients with more physical activity had a higher degree of insulin sensitivity, lower blood pressure, total visceral adipose tissue, and overall lower total mass. Total physical activity levels showed small, but significant correlations with systolic blood pressure, visceral fat, lean mass and insulin sensitivity. After normalizing for the race, age, and gender using multiple regression, these associations were no longer significant considering our small sample size. More research into prediabetes will decrease the population of diabetics overall. In the future, we could increase sample size and conduct cross sectional and longitudinal studies in various populations with prediabetes.Keywords: diabetes, kidney disease, nephrology, prediabetes
Procedia PDF Downloads 1813853 The Strategic Roles of Women in Small Family Businesses: Evidence from Two Emerging Economies in West Africa
Authors: Bamidele Wale-Oshinowo, Doris Akyere Boateng, Lebura Sorbarikor
Abstract:
Women play significant roles when it comes to the survival of family businesses; however, their efforts are less acknowledged across the developing world. In the case where these businesses are started by husbands, women in many instances work as hard as the men to build up the business. In spite of this, the benefits women receive are not equal to their inputs. For instance, the profits accruing from ownership of these businesses are mainly enjoyed by husbands, as they are deemed to be the legal owners of family businesses in most developing economies. Though the number of women involvement in the ownership, management, and direction of family businesses keeps increasing over the years, their efforts sometimes are ‘invisible’ and not rewarded. Using a phenomenological approach, this study purposively selected 20 businesswomen each from Ghana and Nigeria for in-depth interviews on the different roles they play in ensuring the success of their family businesses (FBs). This study also explored the challenges and opportunities that these women have within their family businesses. Among the major findings of this study is the important strategic direction that women give in terms of providing both tangible and intangible resources such as transfer of transit knowledge to the next generation. Women were also found to play a significant role in the implementation of entrepreneurial orientation within small family businesses in Ghana and Nigeria. However, the study revealed that women experience various challenges as stakeholders in family businesses, among which are: work-life balance issues, succession issues, and culture-related presuppositions about gender roles both within the business and in their families. In the light of the study’s findings, critical recommendations made include encouraging founders and/or owners of family businesses to create a conducive and viable platform for women to grow into key leadership positions within Family businesses; doing this would impact strongly on the growth rate of these form of businesses within the African Region.Keywords: emerging economies, control, management, resources, strategy, women
Procedia PDF Downloads 3513852 Energy System Analysis Using Data-Driven Modelling and Bayesian Methods
Authors: Paul Rowley, Adam Thirkill, Nick Doylend, Philip Leicester, Becky Gough
Abstract:
The dynamic performance of all energy generation technologies is impacted to varying degrees by the stochastic properties of the wider system within which the generation technology is located. This stochasticity can include the varying nature of ambient renewable energy resources such as wind or solar radiation, or unpredicted changes in energy demand which impact upon the operational behaviour of thermal generation technologies. An understanding of these stochastic impacts are especially important in contexts such as highly distributed (or embedded) generation, where an understanding of issues affecting the individual or aggregated performance of high numbers of relatively small generators is especially important, such as in ESCO projects. Probabilistic evaluation of monitored or simulated performance data is one technique which can provide an insight into the dynamic performance characteristics of generating systems, both in a prognostic sense (such as the prediction of future performance at the project’s design stage) as well as in a diagnostic sense (such as in the real-time analysis of underperforming systems). In this work, we describe the development, application and outcomes of a new approach to the acquisition of datasets suitable for use in the subsequent performance and impact analysis (including the use of Bayesian approaches) for a number of distributed generation technologies. The application of the approach is illustrated using a number of case studies involving domestic and small commercial scale photovoltaic, solar thermal and natural gas boiler installations, and the results as presented show that the methodology offers significant advantages in terms of plant efficiency prediction or diagnosis, along with allied environmental and social impacts such as greenhouse gas emission reduction or fuel affordability.Keywords: renewable energy, dynamic performance simulation, Bayesian analysis, distributed generation
Procedia PDF Downloads 4893851 Entrepreneurial Orientation and Business Performance: The Case of Micro Scale Food Processors Operating in a War-Recovery Environment
Authors: V. Suganya, V. Balasuriya
Abstract:
The functioning of Micro and Small Scale (MSS) businesses in the northern part of Sri Lanka was vulnerable due to three decades of internal conflict and the subsequent post-war economic openings has resulted new market prospects for MSS businesses. MSS businesses survive and operate with limited resources and struggle to access finance, raw material, markets, and technology. This study attempts to identify the manner in which entrepreneurial orientation puts into practice by the business operators to overcome these business challenges. Business operators in the traditional food processing sector are taken for this study as this sub-sector of the food industry is developing at a rapid pace. A review of the literature was done to recognize the concepts of entrepreneurial orientation, defining MMS businesses and the manner in which business performance is measured. Direct interview method supported by a structured questionnaire is used to collect data from 80 respondents; based on a fixed interval random sampling technique. This study reveals that more than half of the business operators have opted to commence their business ventures as a result of identifying a market opportunity. 41 per cent of the business operators are highly entrepreneurial oriented in a scale of 1 to 5. Entrepreneurial orientation shows significant relationship and strongly correlated with business performance. Pro-activeness, innovativeness and competitive aggressiveness shows a significant relationship with business performance while risk taking is negative and autonomy is not significantly related to business performance. It is evident that entrepreneurial oriented business practices contribute to better business performance even though 70 per cent prefer the ideas/views of the support agencies than the stakeholders when making business decisions. It is recommended that appropriate training should be introduced to develop entrepreneurial skills focusing to improve business networks so that new business opportunities and innovative business practices are identified.Keywords: Micro and Small Scale (MMS) businesses, entrepreneurial orientation (EO), food processing, business operators
Procedia PDF Downloads 4843850 The Impact of Access to Finances on Survival of Small and Medium Enterprises: The South African Perspective in an Covid-19 Era
Authors: Thabiso Sthembiso Msomi
Abstract:
SMEs are the main engine of growth in most developing economies. One of the main factors that hinder the development of SME is access to finance. In this study, we explored the factors that hinder the growth and survival of SMEs in South Africa. The capital structure theory formed the theoretical underpinning for the study. The quantitative research design was adopted and data was collected from retail, construction, manufacturing and agriculture sectors of SMEs within the KwaZulu-Natal province of South Africa. The modified version of the Cochran formula was used to determine the sample size as 321 SMEs and analysed using the five-point Likert scale. The purposive sampling technique was used to select owners of SME. Statistical Package for the Social Sciences (SPSS) was used for the data analysis through Exploratory Factor Analysis (EFA) to determine the factor structures of items employed to measure each of the constructs in this study. Then, the Cronbach’s alpha test was conducted to determine the reliability of each construct. Kaiser-Meyer-Olkin (KMO) was used to determine the adequacy of the sample size. Linear regression was done to determine the effect of the independent variables on the dependent variable. The findings suggest that the main constraints facing South African SMEs were the lack of experienced management. Furthermore, the SMEs would fail to raise customer awareness of their products and services, which in turn affects their market access and monthly turnover. The study recommends that SMEs keep up-to-date records of business transactions to enable the business to keep track of its operations. The study recommends that South African banks adopt an SME accounting and bookkeeping program. The finding of this study benefits policymakers in both the private and public sectors.Keywords: small businesses, access to finances, COVID-19, SMEs survival
Procedia PDF Downloads 1683849 Use of a Business Intelligence Software for Interactive Visualization of Data on the Swiss Elite Sports System
Authors: Corinne Zurmuehle, Andreas Christoph Weber
Abstract:
In 2019, the Swiss Federal Institute of Sport Magglingen (SFISM) conducted a mixed-methods study on the Swiss elite sports system, which yielded a large quantity of research data. In a quantitative online survey, 1151 elite sports athletes, 542 coaches, and 102 Performance Directors of national sports federations (NF) have submitted their perceptions of the national support measures of the Swiss elite sports system. These data provide an essential database for the further development of the Swiss elite sports system. The results were published in a report presenting the results divided into 40 Olympic summer and 14 winter sports (Olympic classification). The authors of this paper assume that, in practice, this division is too unspecific to assess where further measures would be needed. The aim of this paper is to find appropriate parameters for data visualization in order to identify disparities in sports promotion that allow an assessment of where further interventions by Swiss Olympic (NF umbrella organization) are required. Method: First, the variable 'salary earned from sport' was defined as a variable to measure the impact of elite sports promotion. This variable was chosen as a measure as it represents an important indicator for the professionalization of elite athletes and therefore reflects national level sports promotion measures applied by Swiss Olympic. Afterwards, the variable salary was tested with regard to the correlation between Olympic classification [a], calculating the Eta coefficient. To estimate the appropriate parameters for data visualization, the correlation between salary and four further parameters was analyzed by calculating the Eta coefficient: [a] sport; [b] prioritization (from 1 to 5) of the sports by Swiss Olympic; [c] gender; [d] employment level in sports. Results & Discussion: The analyses reveal a very small correlation between salary and Olympic classification (ɳ² = .011, p = .005). Gender demonstrates an even small correlation (ɳ² = .006, p = .014). The parameter prioritization was correlating with small effect (ɳ² = .017, p = .001) as did employment level (ɳ² = .028, p < .001). The highest correlation was identified by the parameter sport with a moderate effect (ɳ² = .075, p = .047). The analyses show that the disparities in sports promotion cannot be determined by a particular parameter but presumably explained by a combination of several parameters. We argue that the possibility of combining parameters for data visualization should be enabled when the analysis is provided to Swiss Olympic for further strategic decision-making. However, the inclusion of multiple parameters massively multiplies the number of graphs and is therefore not suitable for practical use. Therefore, we suggest to apply interactive dashboards for data visualization using Business Intelligence Software. Practical & Theoretical Contribution: This contribution provides the first attempt to use Business Intelligence Software for strategic decision-making in national level sports regarding the prioritization of national resources for sports and athletes. This allows to set specific parameters with a significant effect as filters. By using filters, parameters can be combined and compared against each other and set individually for each strategic decision.Keywords: data visualization, business intelligence, Swiss elite sports system, strategic decision-making
Procedia PDF Downloads 863848 D-Wave Quantum Computing Ising Model: A Case Study for Forecasting of Heat Waves
Authors: Dmytro Zubov, Francesco Volponi
Abstract:
In this paper, D-Wave quantum computing Ising model is used for the forecasting of positive extremes of daily mean air temperature. Forecast models are designed with two to five qubits, which represent 2-, 3-, 4-, and 5-day historical data respectively. Ising model’s real-valued weights and dimensionless coefficients are calculated using daily mean air temperatures from 119 places around the world, as well as sea level (Aburatsu, Japan). In comparison with current methods, this approach is better suited to predict heat wave values because it does not require the estimation of a probability distribution from scarce observations. Proposed forecast quantum computing algorithm is simulated based on traditional computer architecture and combinatorial optimization of Ising model parameters for the Ronald Reagan Washington National Airport dataset with 1-day lead-time on learning sample (1975-2010 yr). Analysis of the forecast accuracy (ratio of successful predictions to total number of predictions) on the validation sample (2011-2014 yr) shows that Ising model with three qubits has 100 % accuracy, which is quite significant as compared to other methods. However, number of identified heat waves is small (only one out of nineteen in this case). Other models with 2, 4, and 5 qubits have 20 %, 3.8 %, and 3.8 % accuracy respectively. Presented three-qubit forecast model is applied for prediction of heat waves at other five locations: Aurel Vlaicu, Romania – accuracy is 28.6 %; Bratislava, Slovakia – accuracy is 21.7 %; Brussels, Belgium – accuracy is 33.3 %; Sofia, Bulgaria – accuracy is 50 %; Akhisar, Turkey – accuracy is 21.4 %. These predictions are not ideal, but not zeros. They can be used independently or together with other predictions generated by different method(s). The loss of human life, as well as environmental, economic, and material damage, from extreme air temperatures could be reduced if some of heat waves are predicted. Even a small success rate implies a large socio-economic benefit.Keywords: heat wave, D-wave, forecast, Ising model, quantum computing
Procedia PDF Downloads 489