Search results for: optimal condition

Authors: Majid Rashidi, Shahrbanoo Farkhondeh Biabnavi

Abstract:

The hydrodynamic instability phenomenon in a journal bearing may occur by either a reduction in the load carried by journal bearing, by an increase in the journal speed, by change in the lubricant viscosity, or a combination of these factors. The previous research and development work done to overcome the instability issue of journal bearings, operating in hydrodynamic lubricate regime, can be categorized as follows: A) Actively controlling the bearing sleeve by using piezo actuator, b) Inclusion of strategically located and shaped internal grooves within inner surface of the bearing sleeve, c) Actively controlling the bearing sleeve using an electromagnetic actuator, d)Actively and externally pressurizing the lubricant within a journal bearing set, and e)Incorporating tilting pads within the inner surface of the bearing sleeve that assume different equilibrium angular position in response to changes in the bearing design parameter such as speed and load. This work presents an innovative design concept for a 'smart journal bearing' set to operate in a stable hydrodynamic lubrication regime, despite variations in bearing speed, load, and its lubricant viscosity. The proposed bearing design allows adjusting its radial clearance for an attempt to maintain a stable bearing operation under those conditions that may cause instability for a bearing with a fixed radial clearance. The design concept allows adjusting the radial clearance at small increments in the order of 0.00254 mm. This is achieved by axially moving two symmetric conical rigid cavities that are in close contact with the conically shaped outer shell of a sleeve bearing. The proposed work includes a 3D model of the bearing that depicts the structural interactions of the bearing components. The 3D model is employed to conduct finite element Analyses to simulate the mechanical behavior of the bearing from a structural point of view. The concept of controlling of the radial clearance, as presented in this work, is original and has not been proposed and discuss in previous research. A typical journal bearing was analyzed under a set of design parameters, namely r =1.27 cm (journal radius), c = 0.0254 mm (radial clearance), L=1.27 cm (bearing length), w = 445N (bearing load), μ = 0.028 Pascale (lubricant viscosity). A shaft speed as 3600 r.p.m was considered, and the mass supported by the bearing, m, is set to be 4.38kg. The Summerfield Number associated with the above bearing design parameters turn to be, S=0.3. These combinations resulted in stable bearing operation. Subsequently, the speed was postulated to increase from 3600 r.p.mto 7200 r.p.m; the bearing was found to be unstable under the new increased speed. In order to regain stability, the radial clearance was increased from c = 0.0254 mm to0.0358mm. The change in the radial clearance was shown to bring the bearing back to stable an operating condition.

Keywords: adjustable clearance, bearing, hydrodynamic, instability, journal

Procedia PDF Downloads 283

Authors: Mehwish Jamil Noor

Abstract:

Morphological features of pollen (sculpturing) were useful for identification of different floral taxa. In this study 49 pollen grains, types belonging to 25 families were studied using Scanning Electron Microscope. Shape and sculpturing of pollen ranging from Psilate, scabrate to reticulate, bireticulate and echinolophate. Honey pollen was identified using morphological features, number and arrangement of pore and colpi, size and shape. It presents the first attempt from Pakistan involving extraction of pollen from honey, its identification and taxonomic analysis. Among pollen studied diversity in shape and sculpturing has been observed ranging from Psilate, scabrate to reticulate to bireticulate and echinolophate condition. Pollen has been identified with the help of morphological feature, number and arrangement of pore and colpi, size and shape, reference slides, light microscopic data and previous literature have been consulted for pollen identification. Pollen of closely related species resemble each other therefore pollen identification of airborne and honey pollen is not possible till species level. Survey of flora was carried in parallel to keep the record about the allergenic and melliferous preference of specific sites through surveys and interviews. Their pollination season and geographical distribution were recorded. Two hundred and five including wild and cultivated taxa were identified belonging to sixty-seven families. Major bee attracting wild shrub and trees includes Justicia adhatoda, Acacia nilotica, Ziziphus jujuba, Taraxicum officinalis, Artemisia dubia, Casuarina sp., Ulmus sp., Broussonetia papyrifera, Cupressus sp. or Pinus roxburghii etc. Cultivated crops like Pennisetum typhoides, Nigella sativa, Triticum sativum along with fruit trees of Pyrus, Prunus, Eryobotria, Citrus etc. are popular melliferous floras. Exotic/ introduced species like Eucalyptus or Parthenium hysterophorus, are also frequently visited by bees indicating the significance of those plants in the honey industry. It is concluded that different microscopic analysis techniques give more clear and authentic pictures of and melliferous pollen identification which is well supported by the floral calendar. The diversity of pollen are observed in case of melliferous pollen, and most of the windborne pollen were found less sculptured or psilate expressing the adaptation to the specific mode of pollination. Pollen morphology and sculpturing would serve as a reference for future studies.

Keywords: pollen, allergenic flora, sem, pollen key, Scanning Electron Microscopy (SEM)

Procedia PDF Downloads 202

Authors: Stephanie Remedios, Linda Veronica Rios

Abstract:

Background. Pediatric obesity is a serious health problem linked to multiple physical diseases and ailments, including diabetes, heart disease, and joint issues. While research has shown pediatric obesity can bring about an array of physical illnesses, it is less known how such a condition can affect children’s cognitive development. With childhood overweight and obesity prevalence rates on the rise, it is essential to understand the scope of their cognitive consequences. The present review of the literature tested the hypothesis that poor physical health, such as childhood obesity or malnutrition, negatively impacts a child’s cognitive development. Methodology. A systematic review was conducted to determine the relationship between poor physical health and lower cognitive functioning in children ages 4-16. Electronic databases were searched for studies dating back to ten years. The following databases were used: Science Direct, FIU Libraries, and Google Scholar. Inclusion criteria consisted of peer-reviewed academic articles written in English from 2012 to 2022 that analyzed the relationship between childhood malnutrition and obesity on cognitive development. A total of 17,000 articles were obtained, of which 16,987 were excluded for not addressing the cognitive implications exclusively. Of the acquired articles, 13 were retained. Results. Research suggested a significant connection between diet and cognitive development. Both diet and physical activity are strongly correlated with higher cognitive functioning. Cognitive domains explored in this work included learning, memory, attention, inhibition, and impulsivity. IQ scores were also considered objective representations of overall cognitive performance. Studies showed physical activity benefits cognitive development, primarily for executive functioning and language development. Additionally, children suffering from pediatric obesity or malnutrition were found to score 3-10 points lower in IQ scores when compared to healthy, same-aged children. Conclusion. This review provides evidence that the presence of physical activity and overall physical health, including appropriate diet and nutritional intake, has beneficial effects on cognitive outcomes. The primary conclusion from this research is that childhood obesity and malnutrition show detrimental effects on cognitive development in children, primarily with learning outcomes. Assuming childhood obesity and malnutrition rates continue their current trade, it is essential to understand the complete physical and psychological implications of obesity and malnutrition in pediatric populations. Given the limitations encountered through our research, further studies are needed to evaluate the areas of cognition affected during childhood.

Keywords: childhood malnutrition, childhood obesity, cognitive development, cognitive functioning

Procedia PDF Downloads 118

Authors: Behzad Babaei, B. Gangadhara Prusty

Abstract:

The objective of this study is to assess the hypotheses that a restored tooth with a class II occlusal-distal (OD) cavity can be strengthened by designing an optimized cavity geometry, as well as selecting the composite restoration with optimized elastic moduli when there is a sharp de-bonded edge at the interface of the tooth and restoration. Methods: A scanned human maxillary molar tooth was segmented into dentine and enamel parts. The dentine and enamel profiles were extracted and imported into a finite element (FE) software. The enamel rod orientations were estimated virtually. Fifteen models for the restored tooth with different cavity occlusal depths (1.5, 2, and 2.5 mm) and internal cavity angles were generated. By using a semi-circular stone part, a 400 N load was applied to two contact points of the restored tooth model. The junctions between the enamel, dentine, and restoration were considered perfectly bonded. All parts in the model were considered homogeneous, isotropic, and elastic. The quadrilateral and triangular elements were employed in the models. A mesh convergence analysis was conducted to verify that the element numbers did not influence the simulation results. According to the criteria of a 5% error in the stress, we found that a total element number of over 14,000 elements resulted in the convergence of the stress. A Python script was employed to automatically assign 2-22 GPa moduli (with increments of 4 GPa) for the composite restorations, 18.6 GPa to the dentine, and two different elastic moduli to the enamel (72 GPa in the enamel rods’ direction and 63 GPa in perpendicular one). The linear, homogeneous, and elastic material models were considered for the dentine, enamel, and composite restorations. 108 FEA simulations were successively conducted. Results: The internal cavity angles (α) significantly altered the peak maximum principal stress at the interface of the enamel and restoration. The strongest structures against the contact loads were observed in the models with α = 100° and 105. Even when the enamel rods’ directional mechanical properties were disregarded, interestingly, the models with α = 100° and 105° exhibited the highest resistance against the mechanical loads. Regarding the effect of occlusal cavity depth, the models with 1.5 mm depth showed higher resistance to contact loads than the model with thicker cavities (2.0 and 2.5 mm). Moreover, the composite moduli in the range of 10-18 GPa alleviated the stress levels in the enamel. Significance: For the class II OD cavity models in this study, the optimal geometries, composite properties, and occlusal cavity depths were determined. Designing the cavities with α ≥100 ̊ was significantly effective in minimizing peak stress levels. The composite restoration with optimized properties reduced the stress concentrations on critical points of the models. Additionally, when more enamel was preserved, the sturdier enamel-restoration interface against the mechanical loads was observed.

Keywords: dental composite restoration, cavity geometry, finite element approach, maximum principal stress

Procedia PDF Downloads 101

Authors: Dimitrios Bakavos, Dimitrios Tsivoulas, Chaowalit Limmaneevichitr

Abstract:

Aluminium cast alloys, of the Al-Si system, are widely used for shape castings. Their microstructures can be further improved on one hand, by alloying modification and on the other, by optimised artificial ageing. In this project four hypoeutectic Al-alloys, the A356, A356+ Ag, A356+Sc, and A356+Ag+Sc have been studied. The interactions of Ag and Sc during solidification and artificial ageing at 170°C to a T6 temper have been investigated in details. The evolution of the eutectic microstructure is studied by thermal analysis and interrupted solidification. The ageing kinetics of the alloys has been identified by hardness measurements. The precipitate phases, number density, and chemical composition has been analysed by means of transmission electron microscopy (TEM) and EDS analysis. Furthermore, the SHT effect onto the Si eutectic particles for the four alloys has been investigated by means of optical microscopy, image analysis, and the UTS strength has been compared with the UTS of the alloys after casting. The results suggest that the Ag additions, significantly enhance the ageing kinetics of the A356 alloy. The formation of β” precipitates were kinetically accelerated and an increase of 8% and 5% in peak hardness strength has been observed compared to the base A356 and A356-Sc alloy. The EDS analysis demonstrates that Ag is present on the β” precipitate composition. After prolonged ageing 100 hours at 170°C, the A356-Ag exhibits 17% higher hardness strength compared to the other three alloys. During solidification, Sc additions change the macroscopic eutectic growth mode to the propagation of a defined eutectic front from the mold walls opposite to the heat flux direction. In contrast, Ag has no significance effect on the solidification mode revealing a macroscopic eutectic growth similar to A356 base alloy. However, the mechanical strength of the as cast A356-Ag, A356-Sc, and A356+Ag+Sc additions has increased by 5, 30, and 35 MPa, respectively. The outcome is a tribute to the refining of the eutectic Si that takes place which it is strong in the A356-Sc alloy and more profound when silver and scandium has been combined. Moreover after SHT the Al alloy with the highest mechanical strength, is the one with Ag additions, in contrast to the as-cast condition where the Sc and Sc+Ag alloy was the strongest. The increase of strength is mainly attributed to the dissolution of grain boundary precipitates the increase of the solute content into the matrix, the spherodisation, and coarsening of the eutectic Si. Therefore, we could safely conclude for an A356 hypoeutectic alloy additions of: Ag exhibits a refining effect on the Si eutectic which is improved when is combined with Sc. In addition Ag enhance, the ageing kinetics increases the hardness and retains its strength at prolonged artificial ageing in a Al-7Si 0.3Mg hypoeutectic alloy. Finally the addition of Sc is beneficial due to the refinement of the α-Al grain and modification-refinement of the eutectic Si increasing the strength of the as-cast product.

Keywords: ageing, casting, mechanical strength, precipitates

Procedia PDF Downloads 498

Authors: J. A. Marañón, L. Lozano C. De Los Santos, L. Martínez-Campesino, E. Caballero-Garrido, F. Galán-Estella

Abstract:

Urinary incontinence (UI) is a significant health problem with considerable social and economic impact. An estimated 30% of women aged 30 to 60 years old have urinary incontinence (UI), while more than 50% of community-dwelling older women have the condition. Stress urinary incontinence and overactive bladder are the common types of incontinence The prevalence of stress and mixed (stress and urge) incontinence is higher than urge incontinence, but the latter is more likely to require treatment. In women, moderate and severe have a prevalence ranging from about 12% to 17% The objectives of this study was to examine the effect of the supplementation of tablets containing Dropsordry in women with urge urinary incontinence (UUI). Dropsordry is a novel active containing phytoestrogens from SOLGEN, the high genistin soy bean extract and pyrogallol plus polyphenols from standarized pumpkin seed extract,. The study was a single-center, not randomiized open prospective, study. 28 women with urinary incontinence ≥45 years were enrolled in this study (45-62 y. old age . Mean 52 y old). Items related to UI symptoms, were previously collected (T0) and these ítems were reviewed at the final of the study – 8 weeks. (T2). The presence of UI was previously diagnosed using the International Continence Society standards (ICS). Relationships between presence of UI and potential related factors as diabetes were also explored. Daily urinary test control was performed during the 8 weeks of treatment. Daily dosage was 1 g/ day (500 mg twice per day) from 0 to 4 week (T1), following a 500 mg/day daily intake from 4 to 8 week (T2). After eight weeks of treatment, the urgency grade score was reduced a 24,7%. The total urge episodes was reduced a 46%. Surprisingly there was no a significant change in daytime urinations (< 5%), however nocturia was reduced a 69,35%. Strenght Urinary Incontinence (SUI) was also tested showing a remarkably 52,17% reduction. Moreover the use of daily pantyliners was reduced a 66,25%. In addition, it was performed a panel test survey with quests when subjects of the study were enrolled (T0) and the same quests was performed after 8 weeks of supplementation (T2). 100% of the enrolled women fullfilled the ICIQ-SF quest (Spanish versión) and they were also questioned about the effects they noticed in response to taking the supplement and the change in quality of life. Interestingly no side effects were reported. There was a 96,2% of subjective satisfaction and a 85,8% objective score in the improvement of quality of life. CONCLUSION: the combination of High genistin isoflavones and pumpkin seed pyrogallol in Dropsordry tablets seems to be a safe and highly effective supplementation for the relieve of the urinary incontinence symptoms and a better quality of life in perimenopause women .

Keywords: isoflavones, pumpkin, menopause, incontinence, genistin

Procedia PDF Downloads 405

Authors: Fabrizio Ascione, Martina Borrelli, Rosa Francesca De Masi, Silvia Ruggiero, Giuseppe Peter Vanoli

Abstract:

The refurbishment of public buildings is one of the key factors of energy efficiency policy of European States. Educational buildings account for the largest share of the oldest edifice with interesting potentialities for demonstrating best practice with regards to high performance and low and zero-carbon design and for becoming exemplar cases within the community. In this context, this paper discusses the critical issue of dealing the energy refurbishment of a university building in heating dominated climate of South Italy. More in detail, the importance of using validated models will be examined exhaustively by proposing an analysis on uncertainties due to modelling assumptions mainly referring to the adoption of stochastic schedules for occupant behavior and equipment or lighting usage. Indeed, today, the great part of commercial tools provides to designers a library of possible schedules with which thermal zones can be described. Very often, the users do not pay close attention to diversify thermal zones and to modify or to adapt predefined profiles, and results of designing are affected positively or negatively without any alarm about it. Data such as occupancy schedules, internal loads and the interaction between people and windows or plant systems, represent some of the largest variables during the energy modelling and to understand calibration results. This is mainly due to the adoption of discrete standardized and conventional schedules with important consequences on the prevision of the energy consumptions. The problem is surely difficult to examine and to solve. In this paper, a sensitivity analysis is presented, to understand what is the order of magnitude of error that is committed by varying the deterministic schedules used for occupation, internal load, and lighting system. This could be a typical uncertainty for a case study as the presented one where there is not a regulation system for the HVAC system thus the occupant cannot interact with it. More in detail, starting from adopted schedules, created according to questioner’ s responses and that has allowed a good calibration of energy simulation model, several different scenarios are tested. Two type of analysis are presented: the reference building is compared with these scenarios in term of percentage difference on the projected total electric energy need and natural gas request. Then the different entries of consumption are analyzed and for more interesting cases also the comparison between calibration indexes. Moreover, for the optimal refurbishment solution, the same simulations are done. The variation on the provision of energy saving and global cost reduction is evidenced. This parametric study wants to underline the effect on performance indexes evaluation of the modelling assumptions during the description of thermal zones.

Keywords: energy simulation, modelling calibration, occupant behavior, university building

Procedia PDF Downloads 141

Authors: Brajendra S. Sengar, Vivek Garg, Gaurav Siddharth, Nisheka Anadkat, Amitesh Kumar, Shaibal Mukherjee

Abstract:

The optimal band gap (~ 1 to 1.5 eV) and high absorption coefficient ~104 cm⁻¹ has made Cu₂ZnSn(S,Se)₄ (CZTSSe) films as one of the most promising absorber materials in thin-film photovoltaics. Additionally, CZTSSe consists of elements that are abundant and non-toxic, makes it even more favourable. The CZTSSe thin films are grown at 100 to 500ᵒC substrate temperature (Tsub) on Soda lime glass (SLG) substrate by Elettrorava dual ion beam sputtering (DIBS) system by utilizing a target at 2.43x10⁻⁴ mbar working pressure with RF power of 45 W in argon ambient. The chemical composition, depth profiling, structural properties and optical properties of these CZTSSe thin films prepared on SLG were examined by energy dispersive X-ray spectroscopy (EDX, Oxford Instruments), Hiden secondary ion mass spectroscopy (SIMS) workstation with oxygen ion gun of energy up to 5 keV, X-ray diffraction (XRD) (Rigaku Cu Kα radiation, λ=.154nm) and Spectroscopic Ellipsometry (SE, M-2000D from J. A. Woollam Co., Inc). It is observed that from that, the thin films deposited at Tsub=200 and 300°C show Cu-poor and Zn-rich states (i.e., Cu/(Zn + Sn) < 1 and Zn/Sn > 1), which is not the case for films grown at other Tsub. It has been reported that the CZTSSe thin films with the highest efficiency are typically at Cu-poor and Zn-rich states. The values of band gap in the fundamental absorption region of CZTSSe are found to be in the range of 1.23-1.70 eV depending upon the Cu/(Zn+Sn) ratio. It is also observed that there is a decline in optical band gap with the increase in Cu/(Zn+Sn) ratio (evaluated from EDX measurement). Cu-poor films are found to have higher optical band gap than Cu-rich films. The decrease in the band gap with the increase in Cu content in case of CZTSSe films may be attributed to changes in the extent of p-d hybridization between Cu d-levels and (S, Se) p-levels. CZTSSe thin films with Cu/(Zn+Sn) ratio in the range 0.86–1.5 have been successfully deposited using DIBS. Optical band gap of the films is found to vary from 1.23 to 1.70 eV based on Cu/(Zn+Sn) ratio. CZTSe films with Cu/ (Zn+Sn) ratio of .86 are found to have optical band gap close to the ideal band gap (1.49 eV) for highest theoretical conversion efficiency. Thus by tailoring the value of Cu/(Zn+Sn), CZTSSe thin films with the desired band gap could be obtained. Acknowledgment: We are thankful to DIBS, EDX, and XRD facility equipped at Sophisticated Instrument Centre (SIC) at IIT Indore. The authors B. S. S and A. K. acknowledge CSIR, and V. G. acknowledges UGC, India for their fellowships. B. S. S is thankful to DST and IUSSTF for BASE Internship Award. Prof. Shaibal Mukherjee is thankful to DST and IUSSTF for BASE Fellowship and MEITY YFRF award. This work is partially supported by DAE BRNS, DST CERI, and DST-RFBR Project under India-Russia Programme of Cooperation in Science and Technology. We are thankful to Mukul Gupta for SIMS facility equipped at UGC-DAE Indore.

Keywords: CZTSSe, DIBS, EDX, solar cell

Procedia PDF Downloads 250

Authors: Mathieu Audet, Monica Soliman, Emilie Eve Gravel, Rebecca Friesdorf

Abstract:

Access to higher education is critical for reducing social inequalities. The Canada Learning Bond (CLB) is a government savings incentive aimed at increasing higher education access for children of low income families by providing money toward a Registered Education Savings Plan. To better understand the educational and financial decision-making of low income families, Employment Social Development Canada conducted qualitative fieldwork with eligible parents and children, teachers, and community organizations promoting the Bond. Insights from this fieldwork were then used to develop letters to better target the needs and experiences of eligible families. In the present study, we conducted a randomized controlled trial with children ages 12 to 13, the oldest cohort of eligible children, to test the effectiveness of the new letters. Parents or caregivers of 150,088 eligible children were assigned to one of five letter conditions promoting the Bond or to a control condition that did not receive a letter. The letter conditions were: (a) the standard letter from past outreach, (b) a letter presenting the exact amount the child was eligible to receive, enhancing the salience of benefits, (c) a letter with a social norm, (d) a letter with an image emphasizing the feasibility of higher education by presenting the diversity of options (i.e., college, trade schools, apprenticeships) – many participants interviewed viewed that university was unfeasible, and (e) a letter minimizing references to 'saving' (i.e., not framing the Bond explicitly as a savings incentive) – a concept that did not resonate with low income families who felt they could not afford to save. The exact amount was also presented in letters (c) through (e). The letter minimizing references to 'saving' and presenting the exact amount had the highest net take-up rate at 6.6%, compared to 3.5% for the standard letter group. Furthermore, this trial’s BI-informed letters showed the largest impact on take-up so far, with a net take-up of 5.7% compared to 3.0% and 3.9% in the first two trials. This research highlights the value of mixed-method approaches combining qualitative and behavioural insights methods for developing context-sensitive interventions for social programs. By gaining a deeper understanding of the needs and experiences of program users through qualitative fieldwork, and then integrating these insights into behaviourally informed communications, we were able to increase take-up of an education savings program, which may ultimately improve access to higher education in children of low income families.

Keywords: access to higher education, behavioral insights, government, innovation, mixed-methods, social programs

Procedia PDF Downloads 124

Authors: Kim Sang Hyuck, Y. Park Sung

Abstract:

The outbreak of national disasters stimulates the decrease of the both internal and domestic tourism demands, causing bad effects on the hospitality industry. The effective and efficient risk management regarding national disasters are being increasingly required from the hospitality industry practitioners and the tourism policymakers. To establish the effective and efficient risk management strategy on national disasters, the most essential prerequisite condition is the correct estimation of national disasters’ effects in terms of the size and duration of the damages occurred from national disaster on hospitality industry. More specifically, the national disasters are twofold: natural disaster and social disaster. In addition, the hospitality industry has consisted of several types of business, such as hotel, restaurant, travel agency, etc. As reasons of the above, it is important to consider how each type of national disasters differently influences on the performance of each type of hospitality industry. Therefore, the purpose of this study is examining the effects of national disaster on hospitality industry in Korea based on the types of national disasters as well as the types of hospitality business. The monthly data was collected from Jan. 2000 to Dec. 2016. The indexes of industrial production for each hospitality industry in Korea were used with the proxy variable for the performance of each hospitality industry. Two national disaster variables (natural disaster and social disaster) were treated as dummy variables. In addition, the exchange rate, industrial production index, and consumer price index were used as control variables in the research model. The impulse response analysis was used to examine the size and duration of the damages occurred from each type of national disaster on each type of hospitality industries. The results of this study show that the natural disaster and the social disaster differently influenced on each type of hospitality industry. More specifically, the performance of airline industry is negatively influenced by the natural disaster at the time of 3 months later from the incidence. However, the negative impacts of social disaster on airline industry occurred not significantly over the time periods. For the hotel industry, both natural disaster and social disaster negatively influence the performance of hotel industry at the time of 5 months and 6 months later, respectively. Also, the negative impact of natural disaster on the performance of restaurant industry occurred at the time of 5 months later, as well as for both 3 months and 6 months later for the social disaster. Finally, both natural disaster and social disaster negatively influence the performance of travel agency at the time of 3 months and 4 months later, respectively. In conclusion, the types of national disasters differently influence the performance of each type of hospitality industry in Korea. These results would provide an important information to establish the effective and efficient risk management strategy for the national disasters.

Keywords: impulse response analysis, Korea, national disaster, performance of hospitality industry

Procedia PDF Downloads 184

Authors: Drago Diaz Aleman, Jose Luis Saorin Perez, Cecile Meier, Itahisa Perez Conesa, Jorge De La Torre Cantero

Abstract:

Traditional manufacturing techniques used in artistic contexts compete with highly productive and efficient industrial procedures. The craft techniques and associated business models tend to disappear under the pressure of the appearance of mass-produced products that compete in all niche markets, including those traditionally reserved for the work of art. The surplus value derived from the prestige of the author, the exclusivity of the product or the mastery of the artist, do not seem to be sufficient reasons to preserve this productive model. In the last years, the adoption of open source digital manufacturing technologies in small art workshops can favor their permanence by assuming great advantages such as easy accessibility, low cost, and free modification, adapting to specific needs of each workshop. It is possible to use pieces modeled by computer and made with FDM (Fused Deposition Modeling) 3D printers that use PLA (polylactic acid) in the procedures of artistic casting. Models printed by PLA are limited to approximate minimum sizes of 3 cm, and optimal layer height resolution is 0.1 mm. Due to these limitations, it is not the most suitable technology for artistic casting processes of smaller pieces. An alternative to solve size limitation, are printers from the type (SLS) "selective sintering by laser". And other possibility is a laser hardens, by layers, metal powder and called DMLS (Direct Metal Laser Sintering). However, due to its high cost, it is a technology that is difficult to introduce in small artistic foundries. The low-cost DLP (Digital Light Processing) type printers can offer high resolutions for a reasonable cost (around 0.02 mm on the Z axis and 0.04 mm on the X and Y axes), and can print models with castable resins that allow the subsequent direct artistic casting in precious metals or their adaptation to processes such as electroforming. In this work, the design of a DLP 3D printer is detailed, using backlit LCD screens with ultraviolet light. Its development is totally "open source" and is proposed as a kit made up of electronic components, based on Arduino and easy to access mechanical components in the market. The CAD files of its components can be manufactured in low-cost FDM 3D printers. The result is less than 500 Euros, high resolution and open-design with free access that allows not only its manufacture but also its improvement. In future works, we intend to carry out different comparative analyzes, which allow us to accurately estimate the print quality, as well as the real cost of the artistic works made with it.

Keywords: traditional artistic techniques, DLP 3D printer, artistic casting, electroforming

Procedia PDF Downloads 142

Authors: Youcef Sehili, Khaled Loubar, Lyes Tarabet, Mahfoudh Cerdoun, Clement Lacroix

Abstract:

As emissions regulations grow more stringent and traditional fuel sources become increasingly scarce, incorporating carbon-free fuels in the transportation sector emerges as a key strategy for mitigating the impact of greenhouse gas emissions. While the utilization of hydrogen (H2) presents significant technological challenges, as evident in the engine limitation known as knocking, ammonia (NH3) provides a viable alternative that overcomes this obstacle and offers convenient transportation, storage, and distribution. Moreover, the implementation of a dual-fuel engine using ammonia as the primary gas is promising, delivering both ecological and economic benefits. However, when employing this combustion mode, the substitution of ammonia at high rates adversely affects combustion performance and leads to elevated emissions of unburnt NH3, especially under high loads, which requires special treatment of this mode of combustion. This study aims to simulate combustion in a common rail direct injection (CRDI) dual-fuel engine, considering the fundamental geometry of the combustion chamber as well as fifteen (15) alternative proposed geometries to determine the configuration that exhibits superior engine performance during high-load conditions. The research presented here focuses on improving the understanding of the equations and mechanisms involved in the combustion of finely atomized jets of liquid fuel and on mastering the CONVERGETM code, which facilitates the simulation of this combustion process. By analyzing the effect of piston bowl shape on the performance and emissions of a diesel engine operating in dual fuel mode, this work combines knowledge of combustion phenomena with proficiency in the calculation code. To select the optimal geometry, an evaluation of the Swirl, Tumble, and Squish flow patterns was conducted for the fifteen (15) studied geometries. Variations in-cylinder pressure, heat release rate, turbulence kinetic energy, turbulence dissipation rate, and emission rates were observed, while thermal efficiency and specific fuel consumption were estimated as functions of crankshaft angle. To maximize thermal efficiency, a synergistic approach involving the enrichment of intake air with oxygen (O2) and the enrichment of primary fuel with hydrogen (H2) was implemented. Based on the results obtained, it is worth noting that the proposed geometry (T8_b8_d0.6/SW_8.0) outperformed the others in terms of flow quality, reduction of pollutants emitted with a reduction of more than 90% in unburnt NH3, and an impressive improvement in engine efficiency of more than 11%.

Keywords: ammonia, hydrogen, combustion, dual-fuel engine, emissions

Procedia PDF Downloads 74

Authors: Luminiţa Duţică, Gheorghe Duţică

Abstract:

Many of the interrogations or dilemmas of the contemporary world found the answer in what was generically called the appeal to matrix. This genuine spiritual exercise of re-connection of the present to origins, to the primary source, revealed the ontological condition of timelessness, ahistorical, immutable (epi)phenomena, of those pure essences concentrated in the archetypal-referential layer of the human existence. The musical creation was no exception to this trend, the impasse generated by the deterministic excesses of the whole serialism or, conversely, by some questionable results of the extreme indeterminism proper to the avant-garde movements, stimulating the orientation of many composers to rediscover a universal grammar, as an emanation of a new ‘collective’ order (reverse of the utopian individualism). In this context, the music of oral tradition and therefore the world of the ancient modes represented a true revelation for the composers of the twentieth century, who were suddenly in front of some unsuspected (re)sources, with a major impact on all levels of edification of the musical work: morphology, syntax, timbrality, semantics etc. For the contemporary Romanian creators, the music of rituals, existing in the local archaic culture, opened unsuspected perspectives for which it meant to be a synthetic, inclusive and recoverer vision, where the primary (archetypal) genuine elements merge with the latest achievements of language of the European composers. Thus, anchored in a strong and genuine modal source, the compositions analysed in this paper evoke, in a manner as modern as possible, the atmosphere of some ancestral rituals such as: the invocation of rain during the drought (Paparudele, Scaloianul), funeral ceremony (Bocetul), traditions specific to the winter holidays and new year (Colinda, Cântecul de stea, Sorcova, Folklore traditional dances) etc. The reactivity of those rituals in the sound context of the twentieth century meant potentiating or resizing the archaic spirit of the primordial symbolic entities, in terms of some complexity levels generated by the technique of harmonies of chordal layers, of complex aggregates (gravitational or non-gravitational, geometric), of the mixture polyphonies and with global effect (group, mass), by the technique of heterophony, of texture and cluster, leading to the implementation of some processes of collective improvisation and instrumental theatre.

Keywords: archetype, improvisation, polyphony, ritual, instrumental theatre

Procedia PDF Downloads 304

Authors: Ramin Hosseinnezhad, Iurii Vozniak, Andrzej Galeski

Abstract:

Shear-induced crystallization, originated from orientation of chains along the flow direction, is an inevitable part of most polymer processing technologies. It plays a dominant role in determining the final product properties and is affected by many factors such as shear rate, cooling rate, total strain, etc. Investigation of the shear-induced crystallization process become of great importance for preparation of nanocomposite, which requires crystallization of nanofibrous sheared inclusions at higher temperatures. Thus, the effects of shear time, shear rate, and also thermal condition of cooling on crystallization of two aliphatic-aromatic copolyesters have been investigated. This was performed using Linkam optical shearing system (CSS450) for both Ecoflex® F Blend C1200 produced by BASF and synthesized copolyester of butylene terephthalate and a mixture of butylene esters: adipate, succinate, and glutarate, (PBASGT), containing 60% of aromatic comonomer. Crystallization kinetics of these biodegradable copolyesters was studied at two different conditions of shearing. First, sample with a thickness of 60µm was heated to 60˚C above its melting point and subsequently subjected to different shear rates (100–800 sec-1) while cooling with specific rates. Second, the same type of sample was cooled down when shearing at constant temperature was finished. The intensity of transmitted depolarized light, recorded by a camera attached to the optical microscope, was used as a measure to follow the crystallization. Temperature dependencies of conversion degree of samples during cooling were collected and used to determine the half-temperature (Th), at which 50% conversion degree was reached. Shearing ecoflex films for 45 seconds with a shear rate of 100 sec-1 resulted in significant increase of Th from 56˚C to 70˚C. Moreover, the temperature range for the transition of molten samples to crystallized state decreased from 42˚C to 20˚C. Comparatively low shift of 10˚C in Th towards higher temperature was observed for PBASGT films at shear rate of 600 sec-1 for 45 seconds. However, insufficient melt flow strength and non-laminar flow due to Taylor vortices was a hindrance to reach more elevated Th at very high shear rates (600–800 sec-1). The shift in Th was smaller for the samples sheared at a constant temperature and subsequently cooled down. This may be attributed to the longer time gap between cessation of shearing and the onset of crystallization. The longer this time gap, the more possibility for crystal nucleus to re-melt at temperatures above Tm and for polymer chains to recoil and relax. It is found that the crystallization temperature, crystallization induction time and spherulite growth of aliphatic-aromatic copolyesters are dramatically influenced by both the cooling rate and the shear imposed during the process.

Keywords: induced crystallization, shear rate, aliphatic-aromatic copolyester, ecoflex

Procedia PDF Downloads 448

Authors: G. A. Oladosu1, P. O. Ogbodogbo, C. I. Makinde1, M. O. Tijani, O. A. Adegboyega

Abstract:

Saprolegniasis is a major pathogenic infection that contributes significantly to poor hatching rates in incubated fish eggs in the Africa catfish hatchery in Nigeria. Malachite green known to be very effective against this condition has been banned because it is carcinogenic. There is, therefore, the need for other effective yet safer methods of controlling saprolegniasis in incubated fish eggs. A total of 50 ml crude, chloroform extract of pyocyanin from which solvent was removed to attain 30 ml, having a concentration of 12.16 ug/ml was produced from 700 ml broth culture of Pseudomonas aeruginosa isolated from a previous study. In-vitro susceptibility of the fungus was investigated by exposing fungal infected eggs to two different time-concentration ratios of pyocyanin; 0.275 ug/ml and 2.75 ug/ml for 1 and 24 hours, and 5 mg/L malachite green as positive control while normal saline was the control. The efficacy of pyocyanin was evaluated using the degree of mycelial growth inhibition in different treatments. Fertilized Clarias gariepinus eggs (between 45 to 64 eggs) were then incubated in 20 ml of medium containing similar concentrations of pyocyanin and malachite green, with freshwater as a control for 24 hours. Hatching rates of the incubated eggs were observed. Three samples of un-hatched eggs were taken from each medium and observed for the presence of fungal pathogens using microscopy. Another batch of three samples of un-hatched eggs from each treatment was also inoculated on Sabourand dextrose agar (SDA) using Egg-Agar Transfer Technique to observe for fungal growth. Mycelial growth was inhibited in fungal infected eggs treated with 2.75 ug/ml for 24 hrs and the 5 mg/L malachite green for both 1 hr and 24 hrs. The mortality rate was 100% in fertilized C. gariepinus eggs exposed for 24 hrs to 0.275 and 2.75 ug/ml of pyocyanin. The mortality rate was least in malachite green followed by the control treatment. Embryonic development was observed to be arrested in the eggs treated with the two pyocyanin concentrations as they maintain their colour but showed no development beyond the gastrula stage, whereas viable eggs in the control and malachite green treatments developed fully into healthy hatchlings. Furthermore, microscopy of the un-hatched eggs revealed the presence of a protozoan ciliate; Colpidium sp, (Tetrahymenidae), as well as a pathogenic fungus; Saprolegnia sp. in the control but not in the malachite green and pyocyanin treatments. Growth of Saprolegnia sp was also observed in SDA culture of un-hatched eggs from the control, but not from pyocyanin and malachite green treated eggs. Pyocyanin treatment of incubated eggs of Clarias gariepinus effectively prevented fungal infection in the eggs, but also arrested the development of the embryo. Therefore, crude chloroform extract of pyocyanin from Pseudomonas aeruginosa cannot be used in the control of Saprolegniasis in incubated Clarias gariepinus eggs at the concentration and duration tested in this study.

Keywords: African catfish, bioprophylaxis, catfish embryo, Saprolegniasis

Procedia PDF Downloads 115

Authors: Steven G. Sclan

Abstract:

Background: Since December 2019, the world has been afflicted by the spread of the Severe Acute Respiratory Syndrome-Corona Virus-2 (SARS-CoV-2), which is responsible for the condition referred to as Covid-19. The illness has had a cataclysmic impact on the political, social, economic, and overall well-being of the population of the entire globe. While Covid-19 has had a substantial universal fatality impact, it may have an even greater effect on the socioeconomic, medical well-being, and healthcare planning for remaining societies. Significance: As these numbers illustrate, many more persons survive the infection than die from it, and many of those patients have noted ongoing, persistent symptoms after successfully enduring the acute phase of the illness. Recognition and understanding of these symptoms are crucial for developing and arranging efficacious models of care for all patients (whether or not having been hospitalized) surviving acute covid illness and plagued by post-acute symptoms. Furthermore, regarding Covid infection in children (< 18 y/o), although it may be that Covid “+” children are not major vectors of infective transmission, it now appears that many more children than initially thought are carrying the virus without accompanying obvious symptomatic expression. It seems reasonable to wonder whether viral effects occur in children – those children who are Covid “+” and now asymptomatic – and if, over time, they might also experience similar symptoms. An even more significant question is whether Covid “+” asymptomatic children might manifest increased multiple health problems as they grow – i.e., developmental complications (e.g., physical/medical, metabolic, neurobehavioral, etc.) – in comparison to children who had been consistently Covid “ - ” during the pandemic. Topics Addressed and Theoretical Importance: This review is important because of the description of both quantitative and qualitative methods for clinical and biomedical research. Topics reviewed will consider the importance of well-designed, comprehensive (i.e., quantitative and qualitative methods) longitudinal studies of Post Covid-19 symptoms in both adults and children. Also reviewed will be general characteristics of longitudinal studies and a presentation of a model for a proposed study. Also discussed will be the benefit of longitudinal studies for the development of efficacious interventions and for the establishment of cogent, practical, and efficacious community healthcare service planning for post-acute covid patients. Conclusion: Results of multi-dimensional, longitudinal studies will have important theoretical implications. These studies will help to improve our understanding of the pathophysiology of long COVID and will aid in the identification of potential targets for treatment. Such studies can also provide valuable insights into the long-term impact of COVID-19 on public health and socioeconomics.

Keywords: COVID-19, post-COVID-19, long COVID, longitudinal research, quantitative research, qualitative research

Procedia PDF Downloads 59

Authors: E. V. Fakhrutdinova, Y. S. Kolesnikova, E. A. Karasik, V. M. Zagidullina

Abstract:

Poverty as the social and economic phenomenon exists in any society and represents a many-sided problem. In this sense it is universal and for many centuries serves as a research objects for scientists. Special attention to a problem of poverty in Russia is caused, first of all, by the critical growth of inequality and by scales of expansion of poverty, considerable decrease in the level and quality of life of the population, decrease in availability of education during the period of reforming. The expansion of poverty on the working members of society, youth, which has to provide reproduction of the population is alarming. As poverty is the reason of weakening of national security of the country, degradation of the population, decline in the quality of the human capital, complication of a demographic situation, strengthening of social contradictions in society, so far as the reduction of poverty, so, the increase in production. Poverty: the characteristic of an economic situation of the individual or social group at which they can't satisfy certain minimum requirements necessary for life, preservations of working capacity and reproduction. Poverty became one of the critical factors expelling people from the system of the institutional interactions reducing social space in which their relations were building breaking their social identity. Complication of the problem of poverty in modern society happened due to penetration of the related relations into many spheres of life. It is known that negative consequences of poverty display not only at the personal level of the poor person, but also at the level of interpersonal social interactions, decline in the quality and level of development of the human capital, and also at social and economic system in general. We conducted a research on the influence of education on the change of poverty level of the population. We consider education as a resource for an increase of the income and social mobility. Dependence of the income of the population on the level of education, availability of education (level of education and quality of education) on the level of income of families is found. Differentiation of quality and number of educational services for children depending on the level of the income of families is revealed. Influence of a factor of poverty on the availability of education is also studied. We consider expenses on education as the limiter of access to education. We consider education as a factor of fixation and aggravation of a property inequality. In the solution of problems of poverty the defining condition is the state regulation of social and economic development by means of creation of the effective institutional environment. The state has to develop measures for an increase of availability of various services to all categories of citizens, in particular services of health care and education, especially for poor citizens enters. The special attention regarding an increase of availability of education services has to be paid to creation of system of social elevators.

Keywords: poverty, education, human capital, quality of life

Procedia PDF Downloads 323

Authors: Ilana Singer, Anastasia Lučić, Julie Leclerc

Abstract:

Introduction: Tics, characterized by repetitive, sudden, non-voluntary motor movements or vocalizations, are prevalent in chronic tic disorder (CT) and Tourette Syndrome (TS). These neurodevelopmental disorders often coexist with various psychiatric conditions, leading to challenges and reduced quality of life. While medication in conjunction with behavioral interventions, such as Habit Reversal Training (HRT), Exposure Response Prevention (ERP), and Comprehensive Behavioral Intervention for Tics (CBIT), has shown efficacy, a significant proportion of patients experience persistent tics. Thus, innovative treatment approaches are necessary to improve therapeutic outcomes, such as mindfulness-based approaches. Nonetheless, the effectiveness of mindfulness-based interventions in the context of CT and TS remains understudied. Objective: The objective of this scoping review is to provide an overview of the current state of research on mindfulness-based interventions for CT and TS, identify knowledge and evidence gaps, discuss the effectiveness of mindfulness-based interventions with other treatment options, and discuss implications for clinical practice and policy development. Method: Using guidelines from Peters (2020) and the PRISMA-ScR, a scoping review was conducted. Multiple electronic databases were searched from inception until June 2023, including MEDLINE, EMBASE, PsychInfo, Global Health, PubMed, Web of Science, and Érudit. Inclusion criteria were applied to select relevant studies, and data extraction was independently performed by two reviewers. Results: Five papers were included in the study. Firstly, we found that mindfulness interventions were found to be effective in reducing anxiety and depression while enhancing overall well-being in individuals with tics. Furthermore, the review highlighted the potential role of mindfulness in enhancing functional connectivity within the Default Mode Network (DMN) as a compensatory function in TS patients. This suggests that mindfulness interventions may complement and support traditional therapeutic approaches, particularly HRT, by positively influencing brain networks associated with tic regulation and control. Conclusion: This scoping review contributes to the understanding of the effectiveness of mindfulness-based interventions in managing CT and TS. By identifying research gaps, this review can guide future investigations and interventions to improve outcomes for individuals with CT or TS. Overall, these findings emphasize the potential benefits of incorporating mindfulness-based interventions as a smaller subset within comprehensive treatment strategies. However, it is essential to acknowledge the limitations of this scoping review, such as the exclusion of a pre-established protocol and the limited number of studies available for inclusion. Further research and clinical exploration are necessary to better understand the specific mechanisms and optimal integration of mindfulness-based interventions with existing behavioral interventions for this population.

Keywords: scoping reviews, Tourette Syndrome, tics, mindfulness-based, therapy, intervention

Procedia PDF Downloads 83

Authors: Priyanka Patil, Logan Manikam

Abstract:

Background: The first 1000 days of life are a critical window and can result in adverse health consequences due to inadequate nutrition. South-Asian (SA) communities face significant health disparities, particularly in maternal and child health. Community-based interventions, often employing Participatory-Learning and Action (PLA) approaches, have effectively addressed health inequalities in lower-income nations. The aim of this study was to assess the feasibility of implementing a PLA intervention to improve infant feeding and care practices in SA communities living in London. Methods: Comprehensive analyses were conducted to assess the feasibility/fidelity of this pilot randomized controlled trial. Summary statistics were computed to compare key metrics, including participant consent rates, attendance, retention, intervention support, and perceived effectiveness, against predefined progression rules guiding toward a definitive trial. Secondary outcomes were analyzed, drawing insights from multiple sources, such as The Children’s-Eating-Behaviour Questionnaire (CEBQ), Parental-Feeding-Style Questionnaires (PFSQ), Food-diary, and the Equality-Impact-Assessment (EIA) tool. A video analysis of children's mealtime behavior trends was conducted. Feedback interviews were collected from study participants. Results: Process-outcome measures met predefined progression rules for a definitive trial, which deemed the intervention as feasible and acceptable. The secondary outcomes analysis revealed no significant changes in children's BMI z-scores. This could be attributed to the abbreviated follow-up period of 6 months, reduced from 12 months, due to COVID-19-related delays. CEBQ analysis showed increased food responsiveness, along with decreased emotional over/undereating. A similar trend was observed in PFSQ. The EIA tool found no potential discrimination areas, and video analysis revealed a decrease in force-feeding practices. Participant feedback revealed improved awareness and knowledge sharing. Conclusion: This study demonstrates that a co-adapted PLA intervention is feasible and well-received in optimizing infant-care practices among South-Asian community members in a high-income country. These findings highlight the potential of community-based interventions to enhance health outcomes, promoting health equity.

Keywords: child health, childhood obesity, community-based, infant nutrition

Procedia PDF Downloads 55

Authors: Robin Root

Abstract:

A fundamental premise of medical anthropology is that clinical phenomena are simultaneously cultural, political, and economic: none more so than the linked acronyms HIV/AIDS. For the medical researcher, HIV/AIDS signals an epidemiological pandemic and a pathophysiology. For persons diagnosed with an HIV-related condition, the acronym often conjures dread, too often marking and marginalizing the afflicted irretrievably. Critical medical anthropology is uniquely equipped to theorize the linkages that bind individual and social wellbeing to global structural and culture-specific phenomena. This paper reports findings from an anthropological study of HIV/AIDS in Swaziland, site of the highest HIV prevalence in the world. The project, initiated in 2005, has documented experiences of HIV/AIDS, religiosity, and treatment and care as well as drought and famine. Drawing on interviews with Swazi religious and traditional leaders about their experiences of leadership amidst worsening economic conditions, environmental degradation, and an ongoing global health crisis, the paper provides uncommon insights for global health practitioners whose singular paradigm for designing and delivering interventions is biomedically-based. In contrast, this paper details the role of local leaders in mediating extreme social suffering and resilience in ways that medical science cannot model but which radically impact how sickness is experienced and health services are delivered and accessed. Two concepts help to organize the paper’s argument. First, a ‘moral economy of language’ is central to showing up the implicit ‘technologies of knowledge’ that inhere in scientific and religious discourses of HIV/AIDS; people draw upon these discourses strategically to navigate highly vulnerable conditions. Second, Paulo Freire’s ethnographic focus on a culture’s 'dangerous words' opens up for examination how ‘sex’ is dangerous for religion and ‘god’ is dangerous for science. The paper interrogates hegemonic and ‘lived’ discourses, both biomedical and religious, and contributes to an important literature on the moral economies of health, a framework of explication and, importantly, action appropriate to a wide-range of contemporary global health phenomena. The paper concludes by asserting that it is imperative that global health planners reflect upon and ‘check’ their hegemonic policy platforms by, one, collaborating with local authoritative agents of ‘what sickness means and how it is best treated,’ and, two, taking account of the structural barriers to achieving good health.

Keywords: Africa, biomedicine, HIV/AIDS, qualitative research , religion

Procedia PDF Downloads 103

Authors: Shiva Naidoo, Kristena Yossef, Grimm Jimm, Mirza Wasique, Eric Kemmerer, Joshua Obuch, Anand Mahadevan

Abstract:

Background: Fiducial markers effectively enhance tumor target visibility prior to Stereotactic Body Radiation Therapy or Proton therapy. To streamline clinical practice, fiducial placement guidelines from a robotic radiosurgery vendor were examined with the goals of optimizing and standardizing feasible geometries for each treatment indication. Clinical examples of prostate, renal, and pancreatic cases are presented. Methods: Vendor guidelines (Accuray, Sunnyvale, Ca) suggest implantation of 4–6 fiducials at least 20 mm apart, with at least a 15-degree angular difference between fiducials, within 50 mm or less from the target centroid, to ensure that any potential fiducial motion (e.g., from respiration or abdominal/pelvic pressures) will mimic target motion. Also recommended is that all fiducials can be seen in 45-degree oblique views with no overlap to coincide with the robotic radiosurgery imaging planes. For the prostate, a standardized geometry that meets all these objectives is a 2 cm-by-2 cm square in the coronal plane. The transperineal implant of two pairs of preloaded tandem fiducials makes the 2 cm-by-2 cm square geometry clinically feasible. This technique may be applied for renal cancer, except repositioned in a sagittal plane, with the retroperitoneal placement of the fiducials into the tumor. Pancreatic fiducial placement via endoscopic ultrasound (EUS) is technically more challenging, as fiducial placement is operator-dependent, and lesion access may be limited by adjacent vasculature, tumor location, or restricted mobility of the EUS probe in the duodenum. Fluoroscopically assisted fiducial placement during EUS can help ensure fiducial markers are deployed with optimal geometry and visualization. Results: Among the first 22 fiducial cases on a newly installed robotic radiosurgery system, live x-ray images for all nine prostatic cases had excellent fiducial visualization at the treatment console. Renal and pancreatic fiducials were not as clearly visible due to difficult target access and smaller caliber insertion needle/fiducial usage. The geometry of the first prostate case was used to ensure accurate geometric marker placement for the remaining 8 cases. Initially, some of the renal and pancreatic fiducials were closer than the 20 mm recommendation, and interactive feedback with the proceduralists led to subsequent fiducials being too far to the edge of the tumor. Further feedback and discussion of all cases are being used to help guide standardized geometries and achieve ideal fiducial placement. Conclusion: The ideal tradeoffs of fiducial visibility versus the thinnest possible gauge needle to avoid complications needs to be systematically optimized among all patients, particularly in regards to body habitus. Multidisciplinary collaboration among proceduralists and radiation oncologists can lead to improved outcomes.

Keywords: fiducial, prostate cancer, renal cancer, pancreatic cancer, radiotherapy

Procedia PDF Downloads 93

Authors: Mahesh Vishwakarma, Sadhana Vishwakarma

Abstract:

Vocational education includes all kind of education which can help students to acquire skills related to a certain profession, art, or activity so that they are able to exercise that profession, art or activity after acquiring such qualification. However, in this global economy of the modern world, job seekers are expected to have certain soft skills over and above the technical knowledge and skills acquired in their areas of expertise. These soft skills include but not limited to interpersonal communication, understanding, personal attributes, problem-solving, working in team, quick adaptability to the workplace environment, and other. Not only the hands-on, job-related skills, and competencies are now being sought by the employers, but also a complex of attitudinal dispositions and affective traits are being looked by them in their prospective employees. This study was performed to identify the employability skills of technical students from an Industrial Training Centre (ITC) in central India. It also aimed to convey a message to the students currently on the role, that for them to remain relevant in the job market, they would need to constantly adapt to changes and evolving requirements in the work environment, including the use of updated technologies. Five hypotheses were formulated and tested on the employability skills of students as a function of gender, trade, work experience, personal attributes, and IT skills. Data were gathered with the help of center’s training officers who approached 200 recently graduated students from the center and administered the instrument to students. All 200 respondents returned the completed instrument. The instrument used for the study consisted of 2 sections; demographic details and employability skills. To measure the employability skills of the trainees, the instrument was developed by referring to the several instruments developed by the past researchers for similar studies. The 1st section of the instrument of demographic details recorded age, gender, trade, year of passing, interviews faced, and employment status of the respondents. The 2nd section of the instrument on employability skills was categorized into seven specific skills: basic vocational skills; personal attributes; imagination skills; optimal management of resources; information-technology skills; interpersonal skills; adapting to new technologies. The reliability and validity of the instrument were checked. The findings revealed valuable information on the relationship and interdependence of vocational education and employability skills of students in the central Indian scenario. The findings revealed a valuable information on supplementing the existing vocational education programs with few soft skills and competencies so as to develop a superior workforce much better equipped to face the job market. The findings of the study can be used as an example by the management of government and private industrial training centers operating in the other parts of the Asian region. Future research can be undertaken on a greater population base from different geographical regions and backgrounds for an enhanced outcome.

Keywords: employability skills, vocational education, industrial training centers, students

Procedia PDF Downloads 132

Authors: Y. Teterin, S. Suleymanova, I. Dmitriev, P. Yartcev

Abstract:

Introduction: One of the most common complications after pancreas transplantation are pancreatic fluid collections (PFCs), which are often complicated not only by infection and subsequent disfunction of the pancreatoduodenal graft (PDG), but also with a rather high mortality rate of recipients. Drainage is not always effective and often requires repeated open surgical interventions, which worsens the outcome of the surgery. Percutaneous drainage of PFCs combined with endoscopic stenting of the main pancreatic duct of the pancreatoduodenal graft (MPDPDG) showed high efficiency in the treatment of PFCs. Aims & Methods: From 01.01.2012 to 31.12.2021 at the Sklifosovsky Research Institute for Emergency Medicine were performed 64 transplantations of PDG. In 11 cases (17.2%), the early postoperative period was complicated by the formation of PFCs. Of these, 7 patients underwent percutaneous drainage of pancreonecrosis with high efficiency and did not required additional methods of treatment. In the remaining 4 patients, drainage was ineffective and was an indication for endoscopic stenting of the MPDPDG. They were the ones who made up the study group. Among them were 3 men and 1 woman. The mean age of the patients was 36,4 years.PFCs in these patients formed on days 1, 12, 18, and 47 after PDG transplantation. We used a gastroscope to stent the MPDPDG, due to anatomical features of the location of the duodenoduodenal anastomosis after PDG transplantation. Through the endoscope channel was performed selective catheterization of the MPDPDG, using a catheter and a guidewire, followed by its contrasting with a water-soluble contrast agent. Due to the extravasation of the contrast, was determined the localization of the defect in the PDG duct system. After that, a plastic pancreatic stent with a diameter of 7 Fr. and a length of 7 cm. was installed along guidewire. The stent was installed in such a way that its proximal edge completely covered the defect zone, and the distal one was determined in the intestinal lumen. Results: In all patients PDG pancreaticography revealed extravasation of a contrast in the area of the isthmus and body of the pancreas, which required stenting of the MPDPDG. In 1 (25%) case, the patient had a dislocation of the stent into the intestinal lumen (III degree according to Clavien-Dindo (2009)). This patient underwent repeated endoscopic stenting of the MPDPDG. On average 23 days after endoscopic stenting of the MPDPDG, the drainage tubes were removed and after approximately 40 days all patients were discharged in a satisfactory condition with follow-up endocrinologist and surgeon consultation. Pancreatic stents were removed after 6 months ± 7 days. Conclusion: Endoscopic stenting of the main pancreatic duct of the donor pancreas is by far the most highly effective and minimally invasive method in the treatment of PFCs after transplantation of the pancreatoduodenal complex.

Keywords: pancreas transplantation, endoscopy surgery, diabetes, stenting, main pancreatic duct

Procedia PDF Downloads 86

Authors: Gunawan Muhammad, Takashi Atsumi, Akira Komaru

Abstract:

Pinctada fucata has been the most important pearl culture species in Japan and known as Japanese Akoya Pearl Oyster. However, during summer 1994, mass mortality devastated pearl culture in most parts of Japan. Therefore, pearl farmers started to import Chinese Pearl Oysters from Hainan Island that came from the same species because they are believed to be more resistant towards high water temperature, despite their lack of ability in producing high-quality pearls. The local farmers were then hybridized Japanese and Chinese pearl oysters and currently known as Hybrid pearl oysters, as an attempt to produce a new oyster's strain which is more resistant towards high temperature but also able to produce higher quality pearls. However, despite both strains were implanted by mantle tissues from the same group of donors, the thickness of pearl nacre produced by both strains was different, even though tablet thickness shows a rather similar pattern. Hence, this leads to a question of whether mother oysters play a major role in both nacre deposition rate and tablet thickness of pearls or not. This study first describes the nacre deposition rate of the shells of Japanese and Hybrid mother oysters towards the water temperature condition in Ago Bay, Mie Prefecture, Japan. Later, a comparative study was conducted among 4 shell positions that had been chosen according to the mantle tissue location and shell growth directions. A correlative study was then taken between shells and pearls nacre deposition rate to know whether mother oyster ability in depositing nacre on their shells is related to that of pearls. All the four shell positions were significantly different in shell nacre growth rate (Kruskal-Wallis, p-value < 0.05), and the third position have faster nacre growth among the other three both in Japanese and Hybrid strains, especially in warm temperature. The ability to deposit nacre between Japanese and Hybrid during warm water conditions (August and September) is also significantly different in almost all positions (Mann Whitney U, p-value < 0.01), Japanese oyster growth faster than Hybrid in all four positions. This leads to a different total growth among the two strains and a higher possibility of thicker nacre thickness in Japanese shell nacre. Tablet thickness is significantly different among all positions of shells (Kruskal-Wallis, p-value < 0.01), the 2nd position deposited rather thinner tablet thickness than the other three, including on the 6th month of culture which is more desirable in producing pearls with good luster. This result gives us new information that pearl growth rate is highly affected by the mother oysters; however, nacre tablet thickness might be the result of the shell matrix expressed by different mantle position from donor oysters.

Keywords: nacre, deposition, biomineralization, pearl aquaculture, pearl oyster, Akoya pearl, pearl

Procedia PDF Downloads 138

Authors: Ambali Alade Odebowale, Andargachew Mekonnen Berhe, Haroldo T. Hattori, Andrey E. Miroshnichenko

Abstract:

Solar thermophotovoltaic systems (STPV) have emerged as a promising solution to overcome the Shockley-Queisser limit, a significant impediment in the direct conversion of solar radiation into electricity using conventional solar cells. The STPV system comprises essential components such as an optical concentrator, selective emitter, and a thermophotovoltaic (TPV) cell. The pivotal element in achieving high efficiency in an STPV system lies in the design of a spectrally selective emitter or absorber. Traditional methods for designing and optimizing selective emitters are often time-consuming and may not yield highly selective emitters, posing a challenge to the overall system performance. In recent years, the application of machine learning techniques in various scientific disciplines has demonstrated significant advantages. This paper proposes a novel nanostructure composed of four-layered materials (SiC/W/SiO2/W) to function as a selective emitter in the energy conversion process of an STPV system. Unlike conventional approaches widely adopted by researchers, this study employs a machine learning-based approach for the design and optimization of the selective emitter. Specifically, a random forest algorithm (RFA) is employed for the design of the selective emitter, while the optimization process is executed using genetic algorithms. This innovative methodology holds promise in addressing the challenges posed by traditional methods, offering a more efficient and streamlined approach to selective emitter design. The utilization of a machine learning approach brings several advantages to the design and optimization of a selective emitter within the STPV system. Machine learning algorithms, such as the random forest algorithm, have the capability to analyze complex datasets and identify intricate patterns that may not be apparent through traditional methods. This allows for a more comprehensive exploration of the design space, potentially leading to highly efficient emitter configurations. Moreover, the application of genetic algorithms in the optimization process enhances the adaptability and efficiency of the overall system. Genetic algorithms mimic the principles of natural selection, enabling the exploration of a diverse range of emitter configurations and facilitating the identification of optimal solutions. This not only accelerates the design and optimization process but also increases the likelihood of discovering configurations that exhibit superior performance compared to traditional methods. In conclusion, the integration of machine learning techniques in the design and optimization of a selective emitter for solar thermophotovoltaic systems represents a groundbreaking approach. This innovative methodology not only addresses the limitations of traditional methods but also holds the potential to significantly improve the overall performance of STPV systems, paving the way for enhanced solar energy conversion efficiency.

Keywords: emitter, genetic algorithm, radiation, random forest, thermophotovoltaic

Procedia PDF Downloads 61

Authors: Monu Ojha, Rahul Rana, Satywati Sharma, Kavya Dashora

Abstract:

The global production rate of plastics has increased enormously and global demand for polyethylene resins –High-density polyethylene (HDPE), Linear low-density polyethylene (LLDPE) and Low-density polyethylene (LDPE) is expected to rise drastically, with very high value. These get accumulated in the environment, posing a potential ecological threat as they are degrading at a very slow rate and remain in the environment indefinitely. The aim of the present study was to investigate the potential of commonly found soil microbes like Bacillus subtilus, Aspergillus niger, Pseudomonas fluroscence for their ability to biodegrade LDPE in the lab on solid and liquid media conditions as well as in presence of 1% salt in the soil. This study was conducted at Indian Institute of Technology, Delhi, India from July to September where average temperature and RH (Relative Humidity) were 33 degrees Celcius and 80% respectively. It revealed that the weight loss of LDPE strip obtained from market of approximately 4x6 cm dimensions is more in liquid broth media than in solid agar media. The percentage weight loss by P. fluroscence, A. niger and B. subtilus observed after 80 days of incubation was 15.52, 9.24 and 8.99% respectively in broth media and 6.93, 2.18 and 4.76 % in agar media. The LDPE strips from same source and on the same were subjected to soil in presence of above microbes with 1% salt (NaCl: obtained from commercial table salt) with temperature and RH 33 degree Celcius and 80%. It was found that the rate of degradation increased in the soil than under lab conditions. The rate of weight loss of LDPE strips under same conditions given in lab was found to be 32.98, 15.01 and17.09 % by P. fluroscence, A. niger and B. subtilus respectively. The breaking strength was found to be 9.65N, 29N and 23.85 N for P. fluroscence, A. niger and B. subtilus respectively. SEM analysis conducted on Zeiss EVO 50 confirmed that surface of LDPE becomes physically weak after biological treatment. There was the increase in the surface roughness indicating Surface erosion of LDPE film. FTIR (Fourier-transform infrared spectroscopy) analysis of the degraded LDPE films showed stretching of aldehyde group at 3334.92 and 3228.84 cm-1,, C–C=C symmetric of aromatic ring at 1639.49 cm-1.There was also C=O stretching of aldehyde group at 1735.93 cm-1. N=O peak bend was also observed which corresponds to 1365.60 cm-1, C–O stretching of ether group at 1217.08 and 1078.21 cm-1.

Keywords: microbial degradation, LDPE, Aspergillus niger, Bacillus subtilus, Peudomonas fluroscence, common salt

Procedia PDF Downloads 165

Authors: Allaire Eric, Hauet Pascal, Floresco Jean, Beley Sebastien, Sussman Helene, Virag Ronald

Abstract:

Background: Caverno-venous leakage (CVL) is devastating, although barely known disease, the first cause of major physical impairment in men under 25, and responsible for 50% of resistances to phosphodiesterase 5-inhibitors (PDE5-I), affecting 30 to 40% of users in this medication class. In this condition, too early blood drainage from corpora cavernosa prevents penile rigidity and penetration during sexual intercourse. The role of conservative surgery in this disease remains controversial. Aim: Assess complications and results of combined open surgery and embolization for CVL. Method: Between June 2016 and September 2021, 133 consecutive patients underwent surgery in our institution for CVL, causing severe erectile dysfunction (ED) resistance to oral medical treatment. Procedures combined vein embolization and ligation with microsurgical techniques. We performed a pre-and post-operative clinical (Erection Harness Scale: EHS) hemodynamic evaluation by duplex sonography in all patients. Before surgery, the CVL network was visualized by computed tomography cavernography. Penile EMG was performed in case of diabetes or suspected other neurological conditions. All patients were optimized for hormonal status—data we prospectively recorded. Results: Clinical signs suggesting CVL were ED since age lower than 25, loss of erection when changing position, penile rigidity varying according to the position. Main complications were minor pulmonary embolism in 2 patients, one after airline travel, one with Factor V Leiden heterozygote mutation, one infection and three hematomas requiring reoperation, one decreased gland sensitivity lasting for more than one year. Mean pre-operative pharmacologic EHS was 2.37+/-0.64, mean pharmacologic post-operative EHS was 3.21+/-0.60, p<0.0001 (paired t-test). The mean EHS variation was 0.87+/-0.74. After surgery, 81.5% of patients had a pharmacologic EHS equal to or over 3, allowing for intercourse with penetration. Three patients (2.2%) experienced lower post-operative EHS. The main cause of failure was leakage from the deep dorsal aspect of the corpus cavernosa. In a 14 months follow-up, 83.2% of patients had a clinical EHS equal to or over 3, allowing for sexual intercourse with penetration, one-third of them without any medication. 5 patients had a penile implant after unsuccessful conservative surgery. Conclusion: Open surgery combined with embolization for CVL is an efficient approach to CVL causing severe erectile dysfunction.

Keywords: erectile dysfunction, cavernovenous leakage, surgery, embolization, treatment, result, complications, penile duplex sonography

Procedia PDF Downloads 149

Authors: Rossana Roila, Raffaella Branciari, Lorenzo Cardinali, David Ranucci

Abstract:

The wild boar (Sus scrofa) population has strongly increased across Europe in the last decades, also causing severe fauna management issues. In central Italy, wild boar is the main hunted wild game species, with approximately 40,000 animals killed per year only in the Umbria region. The meat of the game is characterized by high-quality nutritional value as well as peculiar taste and aroma, largely appreciated by consumers. This type of meat and products thereof can meet the current consumers’ demand for higher quality foodstuff, not only from a nutritional and sensory point of view but also in relation to environmental sustainability, the non-use of chemicals, and animal welfare. The game meat production chain is characterized by some gaps from a hygienic point of view: the harvest process is usually conducted in a wild environment where animals can be more easily contaminated during hunting and subsequent practices. The definition and implementation of a certified and controlled supply chain could ensure quality, traceability and safety for the final consumer and therefore promote game meat products. According to European legislation in some animal species, such as bovine, the use of weak acid solutions for carcass decontamination is envisaged in order to ensure the maintenance of optimal hygienic characteristics. A preliminary study was carried out to evaluate the applicability of similar strategies to control the hygienic level of wild boar carcasses. The carcasses, harvested according to the selective method and processed into the game-handling establishment, were treated by nebulization with two different solutions: a 2% food-grade lactic acid solution and aromatic vinegar. Swab samples were performed before treatment and in different moments after-treatment of the carcasses surfaces and subsequently tested for Total Aerobic Mesophilic Load, Total Aerobic Psychrophilic Load, Enterobacteriaceae, Staphylococcus spp. and lactic acid bacteria. The results obtained for the targeted microbial populations showed a positive effect of the application of the lactic acid solution on all the populations investigated, while aromatic vinegar showed a lower effect on bacterial growth. This study could lay the foundations for the optimization of the use of a lactic acid solution to treat wild boar carcasses aiming to guarantee good hygienic level and safety of meat.

Keywords: game meat, food safety, process hygiene criteria, microbial population, microbial growth, food control

Procedia PDF Downloads 158

Authors: Yamina Boughari, Ruxandra Mihaela Botez, Florian Theel, Georges Ghazi

Abstract:

Clearance of flight control laws of a civil aircraft is a long and expensive process in the Aerospace industry. Thousands of flight combinations in terms of speeds, altitudes, gross weights, centers of gravity and angles of attack have to be investigated, and proved to be safe. Nonetheless, in this method, a worst flight condition can be easily missed, and its missing would lead to a critical situation. Definitively, it would be impossible to analyze a model because of the infinite number of cases contained within its flight envelope, that might require more time, and therefore more design cost. Therefore, in industry, the technique of the flight envelope mesh is commonly used. For each point of the flight envelope, the simulation of the associated model ensures the satisfaction or not of specifications. In order to perform fast, comprehensive and effective analysis, other varying parameters models were developed by incorporating variations, or uncertainties in the nominal models, known as Linear Fractional Representation LFR models; these LFR models were able to describe the aircraft dynamics by taking into account uncertainties over the flight envelope. In this paper, the LFRs models are developed using the speeds and altitudes as varying parameters; The LFR models were built using several flying conditions expressed in terms of speeds and altitudes. The use of such a method has gained a great interest by the aeronautical companies that have seen a promising future in the modeling, and particularly in the design and certification of control laws. In this research paper, we will focus on the Cessna Citation X open loop stability analysis. The data are provided by a Research Aircraft Flight Simulator of Level D, that corresponds to the highest level flight dynamics certification; this simulator was developed by CAE Inc. and its development was based on the requirements of research at the LARCASE laboratory. The acquisition of these data was used to develop a linear model of the airplane in its longitudinal and lateral motions, and was further used to create the LFR’s models for 12 XCG /weights conditions, and thus the whole flight envelope using a friendly Graphical User Interface developed during this study. Then, the LFR’s models are analyzed using Interval Analysis method based upon Lyapunov function, and also the ‘stability and robustness analysis’ toolbox. The results were presented under the form of graphs, thus they have offered good readability, and were easily exploitable. The weakness of this method stays in a relatively long calculation, equal to about four hours for the entire flight envelope.

Keywords: flight control clearance, LFR, stability analysis, robustness analysis

Procedia PDF Downloads 352

Authors: A. Sekhar, N. Ramakrishna Raju

Abstract:

This paper is a result of ground improvement using deep vibro techniques with combination of sand and stone columns performed on a highly liquefaction susceptible site (70 to 80% sand strata and balance silt) with low bearing capacities due to high settlements located (earth quake zone V as per IS code) at Madhepura, Bihar state in northern part of India. Initially, it was envisaged with bored cast in-situ/precast piles, stone/sand columns. However, after detail analysis to address both liquefaction and improve bearing capacities simultaneously, it was analyzed the deep vibro techniques with combination of sand and stone columns is excellent solution for given site condition which may be first time in India. First after detail soil investigation, pre eCPT test was conducted to evaluate the potential depth of liquefaction to densify silty sandy soils to improve factor of safety against liquefaction. Then trail test were being carried out at site by deep vibro compaction technique with sand and stone columns combination with different spacings of columns in triangular shape with different timings during each lift of vibro up to ground level. Different spacings and timing was done to obtain the most effective spacing and timing with vibro compaction technique to achieve maximum densification of saturated loose silty sandy soils uniformly for complete treated area. Then again, post eCPT test and plate load tests were conducted at all trail locations of different spacings and timing of sand and stone columns to evaluate the best results for obtaining the required factor of safety against liquefaction and the desired bearing capacities with reduced settlements for construction of industrial structures. After reviewing these results, it was noticed that the ground layers are densified more than the expected with improved factor of safety against liquefaction and achieved good bearing capacities for a given settlements as per IS codal provisions. It was also worked out for cost-effectiveness of lightly loaded single storied structures by using deep vibro technique with sand column avoiding stone. The results were observed satisfactory for resting the lightly loaded foundations. In this technique, the most important is to mitigating liquefaction with improved bearing capacities and reduced settlements to acceptable limits as per IS: 1904-1986 simultaneously up to a depth of 19M. To our best knowledge it was executed first time in India.

Keywords: ground improvement, deep vibro techniques, liquefaction, bearing capacity, settlement

Procedia PDF Downloads 197