Search results for: Antônio Carlos Júnior

Authors: Edwin Oviedo, Carlos Linares, Philippe Ayrault, Sylvette Brunet

Abstract:

Nowadays, light conventional crude oils are going down. Therefore, the exploitation of heavy crude oils has been increasing. Hence, a major quantity of refractory sulfur compounds such as dibenzothiophene (DBT) should be removed. Many efforts have been carried out to modify hydrotreatment typical supports in order to increase hydrodesulfurization (HDS) reactions. The present work shows the synthesis of tertiaries MgFeAl(0.16), MgFeAl(0.32), CoFeAl, ZnFeAl hydrotalcites, as supports of CoMo based catalysts, where 0.16 and 0.32 are the Fe3+/Al3+ molar ratio. Solids were characterized by different techniques (XRD, CO2-TPD, H2-TPR, FT-IR, BET, Chemical Analysis and HRTEM) and tested in the DBT HDS reaction. The reactions conditions were: Temp=325°C, P=40 Bar, H2/feed=475. Results show that the catalysts CoMo/MgFeAl(0.16) and CoMo/MgFeAl(0.32), which were the most basics, reduced the sulfur content from 500ppm to less than 1 ppm, increasing the cyclohexylbenzene content, i.e. presented a higher selective toward the HYD pathway than reference catalyst CoMo/γ- Al2O3. This is suitable for improving the fuel quality due to the increase of the cetane number. These catalysts were also more active to the HDS reaction increasing the direct desulfurization (DDS) way and presented a good stability. It is advantageous when the gas oil centane number should be improved. Cobalt, iron or zinc species inside support could avoid the Co and Mo dispersion or form spinel species which could be less active to hydrodesulfuration reactions, while hydrotalcites containing Mg increases the HDS activity probably due to improved Co/Mo ratio.

Keywords: catalyst, cetane number, dibenzothiophene, diesel, hydrodesulfurization, hydrotreatment, MoS2

Procedia PDF Downloads 155

Authors: Frappi Sofia, Nicolas Pilcher, Sander DenHaring, Royale Hardenstine, Luis Silva, Collin Williams, Mattie Rodrigue, Vincent Pieriborne, Mohammed Qurban, Carlos M. Duarte

Abstract:

Nowadays, elasmobranch populations are disappearing at a dangerous rate, mainly due to overexploitation, extensive fisheries, as well as climate change. The decline of these species can trigger a cascade effect, which may eventually lead to detrimental impacts on local ecosystems. The Elasmobranch in the Red Sea is facing one of the highest risks of extinction, mainly due to unregulated fisheries activities. Thus, it is of paramount importance to assess their current distribution and unveil their environmental preferences in order to improve conservation measures. Important data have been collected throughout the whole red Sea during the Red Sea Decade Expedition (RSDE) to achieve this goal. Elasmobranch sightings were gathered through the use of submarines, remotely operated underwater vehicles (ROV), scuba diving operations, and helicopter surveys. Over a period of 5 months, we collected 891 sightings, 52 with submarines, 138 with the ROV, 67 with the scuba diving teams, and 634 from helicopters. In total, we observed 657 and 234 individuals from the superorder Batoidea and Selachimorpha, respectively. The most common shark encountered was Iago omanensis, a deep-water shark of the order Carcharhiniformes. To each sighting, data on temperature, salinity density, and dissolved oxygen were integrated to reveal favorable conditions for each species. Additionally, an extensive literature review on elasmobranch research in the Eastern Red Sea has been carried out in order to obtain more data on local populations and to be able to highlight patterns of their distribution.

Keywords: distribution, elasmobranchs, habitat, rays, red sea, sharks

Procedia PDF Downloads 76

Authors: May Maricel De Gracia

Abstract:

Different generations respond differently to instruction because of their diverse characteristics, learning styles and study habits. Teaching strategies that were effective many years ago may not be effective now especially to the current generation which is Gen Z. Using quantitative research design, the main goal of this paper is to determine the impact of the implementation of educational technology integration in a private high school in the math performance of its Junior High School (JHS) students on SY 2014-2018 based on their periodical exam performance and on their final math grades. In support, survey on the use of technology was administered to determine the characteristics of both students and teachers of SY 2017-2018. Another survey regarding study habits was also administered to the students to determine their readiness with regards to note-taking skills, time management, test taking/preparation skills, reading, and writing and math skills. Teaching strategies were recommended based on the need of the current Gen Z JHS students. A total of 712 JHS students and 12 math teachers participated in answering the different surveys. Periodic exam means and final math grades between the school years without technology (SY 2004-2008) and with technology (SY 2014-2018) were analyzed through correlation and regression analyses. Result shows that the periodic exam mean has a 35.29% impact to the final grade of the students. In addition, z-test result where p > 0.05 shows that the periodical exam results do not differ significantly between the school years without integration of technology and with the integration of technology. However, with p < 0.01, a significant positive difference was observed in the final math grades of students between the school years without technology integration and with technology integration.

Keywords: classroom instruction, technology, generation z, math performance

Procedia PDF Downloads 144

Authors: Antonio De Lisa

Abstract:

The aim of this contribution is to describe a Sufi ceremony personally observed and recorded in Istanbul. It is part of research on the semiotics of religion that has been going on for some time. Over the centuries, Sufism has produced remarkable literature, elaborated mainly in the context of Arabic literature and Persian literature, but has also found expression in many other languages (Turkish, Indian, Malayo-Indonesian, etc.). Among the genres cultivated are: devotional books (prayers, meditation, spiritual exercises, etc.); the hagiographic texts, containing the biographies and sentences of the best-known Sufis; the texts that illustrate the abodes or stations of the spiritual path; finally, the theoretical treatises on various topics, often of an apologetic nature. Another typical expression of Sufism is in the literature in verse, which includes first-rate poets of both Arabic (Ibn al-Farid, Ibn 'Arabi) and Persian (Farid al-Din al-Attar, Rumi, Hafez, Gohar Shahi) expression. To observe an authentic Sufi ceremony, we contacted the Silivrikapı Mevlana Cultural Center in Istanbul. The ceremony we will talk about is a characteristic of the brotherhood called Mevleviyye (Mawlawiyya), so called from Mawlānā ('our lord', in Turkish: Mevlānā) Jalāl al-Dīn Muḥammad Rūmī (13th century) better known as the brotherhood of the Whirling Dervishes, founded in Konya. The characteristic of the order is to pray about one's love for Allah with music and dance in a ritual that has the name of Semà. The dance is a swirling movement in a group, representing a mystical journey of the spiritual ascent of man through the mind and love for the 'perfect'. Turning towards the truth, the follower of the group ascends towards love, passing beyond the World and Nothingness. After asceticism, he returns to the common world to communicate his own experience.

Keywords: semiotics of religion, sufi, rumi, islamic philosophy

Procedia PDF Downloads 84

Authors: Ling Xu, Giuseppe Loprencipe, Antonio D'Andrea

Abstract:

Asphalt pavement with recycled and sustainable materials has become the most commonly adopted strategy for road construction, including reclaimed asphalt pavement (RAP) and crumb rubber (CR) from waste tires. However, the adhesion and cohesion characteristics of rubberized reclaimed asphalt pavement were still ambiguous, resulting in deteriorated adhesion behavior and life performance. This research investigated the effect of bonding characteristics on rutting resistance and moisture susceptibility of rubberized reclaimed asphalt pavement in terms of two RAP sources with different oxidation levels and two tire rubber with different particle sizes. Firstly, the binder bond strength (BBS) test and bonding failure distinguishment were conducted to analyze the surface behaviors of binder-aggregate interaction. Then, the compatibility and penetration grade of rubberized RAP binder were evaluated by rotational viscosity test and penetration test, respectively. Hamburg wheel track (HWT) test with high-temperature viscoelastic deformation analysis was adopted, which illustrated the rutting resistance. Additionally, a water boiling test was employed to evaluate the moisture susceptibility of the mixture and the texture features were characterized with the statistical parameters of image colors. Finally, the colloid structure model of rubberized RAP binder with surface interaction was proposed, and statistical analysis was established to release the correlation among various indexes. This study concluded that the gel-phase colloid structure and molecular diffusion of the free light fraction would affect the surface interpretation with aggregate, determining the bonding characteristic of rubberized RAP asphalt.

Keywords: bonding characteristics, reclaimed asphalt pavement, rubberized asphalt, sustainable material

Procedia PDF Downloads 57

Authors: Rolando Barradas, Salviano Soares, António Valente, José Alberto Lencastre, Paulo Oliveira

Abstract:

This article reviews the Ant Colony Optimization, a nature-inspired algorithm, and its implementation in the Scratch/m-Block programming environment. The Ant Colony Optimization is a part of Swarm Intelligence-based algorithms and is a subset of biological-inspired algorithms. Starting with a problem in which one has a maze and needs to find its path to the center and return to the starting position. This is similar to an ant looking for a path to a food source and returning to its nest. Starting with the implementation of a simple wall follower simulator, the proposed solution uses a dynamic graphical interface that allows young students to observe the ants’ movement while the algorithm optimizes the routes to the maze’s center. Things like interface usability, Data structures, and the conversion of algorithmic language to Scratch syntax were some of the details addressed during this implementation. This gives young students an easier way to understand the computational concepts of sequences, loops, parallelism, data, events, and conditionals, as they are used through all the implemented algorithms. Future work includes the simulation results with real contest mazes and two different pheromone update methods and the comparison with the optimized results of the winners of each one of the editions of the contest. It will also include the creation of a Digital Twin relating the virtual simulator with a real micromouse in a full-size maze. The first test results show that the algorithm found the same optimized solutions that were found by the winners of each one of the editions of the Micromouse contest making this a good solution for maze pathfinding.

Keywords: nature inspired algorithms, scratch, micromouse, problem-solving, computational thinking

Procedia PDF Downloads 116

Authors: Claire B. Salvedia, Enrico P. Supangco, Francisco B. Eligado, Renato Sa Vega, Antonio A. Rayos

Abstract:

The study was conducted to evaluate the effect of probiotic feeding on weight gain, blood biochemical and hematological indices of crossbred dairy goat kids. Sixteen (16) crossbred Anglo-Nubian x Saanen dairy goat kids, 3 to 4 months old, ranging from 19 to 23kg were randomly assigned into four treatments fed with 5x109 cfu/ml probiotic supplements; Treatment 1 – control; Treatment 2 – lactic acid bacteria (L. plantarum BS and P. acidilactici 3G3); treatment 3 – S. cerevisiae 2030; Treatment 4 – multi-strain probiotics (L. plantarum BS, P. acidilactici 3G3, and S.cerevisiae 2030). Feed ration provided daily for each of the experimental animals were composed of 1kg mixed concentrate feed ((Leucaena leucocephala dried leaves and pollard), and 4 kg fresh Pennisetum purpureum and Gliciridia sepium leaves (50:50). The experimental feeding trial lasted for 9 weeks. Result revealed that treatments fed with probiotics had significantly (P≤0.05) higher weight gain compared to the control. Significant effect on plasma urea nitrogen (PUN) and triglyceride were noted during 30th and 60th day of probiotic feeding. White blood cell counts were significantly affected by probiotic feeding during the 60th day. Concentrations of glucose and cholesterol remained unchanged throughout the experimental period. The findings suggests, under the condition of the experiment, that live probiotic feeding could have a significant role in improving weight gain and metabolism of crossbred dairy goat kids.

Keywords: probiotics, weight gain, blood biochemical indices, crossbred dairy goat kids

Procedia PDF Downloads 479

Authors: Ajmal Hussain

Abstract:

In Indian music parlance, Rasa denotes a distinct aesthetic experience that builds up in the mind of the listeners while listening to a piece of Indian classical music. The distinction of the experience is rooted in the concept that it gives rise to an enhanced awareness about the Self or God and creates a mental state detached from mundane issues of everyday life. The theory of Rasa was initially proposed in the context of theatre but became a part of Indian musicological discourse roughly two thousand years ago, however, to this day, it remains shrouded in mystery due to its religious associations and connotations. This paper attempts to demystify the theory of Rasa in the light of available scientific knowledge fund particularly in Brain and Mind sciences. The paper initially describes the religious context of the theory of Rasa and then discusses its classical formulations by Bharata and Abhinavagupta including the steps and stages laid down by the latter to explain the creation of musical experience. The classical formulations are then interpreted with reference to the scientific knowledge fund about the human mind and mechanics of perception. The study uses the model of human mind as proposed by Portuguese-American neuroscientist Antonio Damasio in his theory ‘A Nesting Principle’. On the basis of the findings by Damasio, the paper interprets the experience of Rasa from a scientific perspective and clarifies the sequence of steps and stages involved in the making of musical experience. The study concludes that although the classical formulations of Rasa identify key aspects of musical experience, the association of Rasa with religion is misleading. The association with religion does not depend upon musical stimulus but the intellectual orientation of the listener. It further establishes that the function of Rasa is more profound as, from an evolutionary perspective, it can be seen as a catalyst for higher consciousness.

Keywords: aesthetic, consciousness, music, Rasa

Procedia PDF Downloads 126

Authors: Luiz Carlos Wrobel, Matjaz Hribersek, Jure Marn, Jurij Iljaz

Abstract:

Dynamic thermography has been clinically proven to be a valuable diagnostic technique for skin tumor detection as well as for other medical applications such as breast cancer diagnostics, diagnostics of vascular diseases, fever screening, dermatological and other applications. Thermography for medical screening can be done in two different ways, observing the temperature response under steady-state conditions (passive or static thermography), and by inducing thermal stresses by cooling or heating the observed tissue and measuring the thermal response during the recovery phase (active or dynamic thermography). The numerical modelling of heat transfer phenomena in biological tissue during dynamic thermography can aid the technique by improving process parameters or by estimating unknown tissue parameters based on measured data. This paper presents a nonlinear numerical model of multilayer skin tissue containing a skin tumor, together with the thermoregulation response of the tissue during the cooling-rewarming processes of dynamic thermography. The model is based on the Pennes bioheat equation and solved numerically by using a subdomain boundary element method which treats the problem as axisymmetric. The paper includes computational tests and numerical results for Clark II and Clark IV tumors, comparing the models using constant and temperature-dependent thermophysical properties, which showed noticeable differences and highlighted the importance of using a local thermoregulation model.

Keywords: boundary element method, dynamic thermography, static thermography, skin tumor diagnostic

Procedia PDF Downloads 99

Authors: Carla Pérez-Chirinos Buxadé, Bruno Fernández-Valdés, Mónica Morral-Yepes, Sílvia Tuyà Viñas, Josep Maria Padullés Riu, Gerard Moras Feliu

Abstract:

There is a long way to explore all the possible applications inertial measurement units (IMUs) have in the sports field. The aim of this study was to evaluate the validity of a new application on the use of these wearable sensors, specifically it was to evaluate a magnet-based timing system (M-BTS) for timing gate-to-gate in an alpine ski slalom using the magnetometer embedded in an IMU. This was a validation study. The criterion validity of time measured by the M-BTS was assessed using the 95% error range against actual time obtained from photocells. The experiment was carried out with first-and second-year junior skiers performing a ski slalom on a ski training slope. Eight alpine skiers (17.4 ± 0.8 years, 176.4 ± 4.9 cm, 67.7 ± 2.0 kg, 128.8 ± 26.6 slalom FIS-Points) participated in the study. An IMU device was attached to the skier’s lower back. Skiers performed a 40-gate slalom from which four gates were assessed. The M-BTS consisted of placing four bar magnets buried into the snow surface on the inner side of each gate’s turning pole; the magnetometer built into the IMU detected the peak-shaped magnetic field when passing near the magnets at a certain speed. Four magnetic peaks were detected. The time compressed between peaks was calculated. Three inter-gate times were obtained for each system: photocells and M-BTS. The total time was defined as the time sum of the inter-gate times. The 95% error interval for the total time was 0.050 s for the ski slalom. The M-BTS is valid for timing gate-to-gate in an alpine ski slalom. Inter-gate times can provide additional data for analyzing a skier’s performance, such as asymmetries between left and right foot.

Keywords: gate crossing time, inertial measurement unit, timing system, wearable sensor

Procedia PDF Downloads 178

Authors: Gláucio de Castro Júnior, Daniela Prometi, Patrícia Tuxi

Abstract:

The project 'Inventory Signs-terms of the cultural heritage field in Libras' provides for the establishment of an inventory of signs, terms relating to the field of cultural heritage in Libras, from the results of research in progress as the pilot project' Accessibility Communication, Translation and Interpretation to the Application Portal Libras Heritage 'and the Pilot Project' registration-signal terms for the preparation of bilingual lexicon Libras / Portuguese terms available in the Portal Heritage. The project's goal is to spread the lexicographical rules on the use of technologies in video graphic records of sign language and foster the training of undergraduate students and graduate to the registration of the linguistic diversity of Libras through social and communicative interaction with the community deaf and enable access to Deaf information relating to the field of cultural heritage in Libras. As a result, we expect the spread of the inventory of cultural heritage-signs in terms Libras in application usage 'Portal Heritage'. To achieve the proposed objectives are accomplished technical consulting and continuous training for the production of academic material through theoretical and practical meetings, taught by experts Libras LIP / UNB in partnership with some institutions. The Inventory project signals-Terms under Heritage in Libras field initially took place in Rio de Janeiro in order to allow its development in the Midwest region, due to technical, elected some cities in Brazil, including Manaus in Amazon Macapa in Amapa, Salvador Bahia, Goiás and Goiânia in Florianopolis in Santa Catarina. At the end of all this process, the assessment by preparing a technical report presenting all the advances and points achieved in the project looking for social improvement, economic, environmental and language in the use of technology will be conducted.

Keywords: signs-terms, equity-cultural accessibility, technology, sign language

Procedia PDF Downloads 415

Authors: Lissette Alejandra Lara, Mario Gomez, Jose Carlos Rodriguez

Abstract:

ransnational corporations (TNCs) as units in which it is possible technology and knowledge transfer across borders and the potential for generating innovation and contributing in economic development both in home and host countries have been widely acknowledged in the foreign direct investment (FDI) literature. Particularly, the accelerated expansion of emerging countries TNCs in the last decades has guided an uprising research stream that measure the presence of reverse technology transfer, defined as the extent to which emerging countries’ TNCs use outward FDI in a host country through certain mechanisms to absorb and transfer knowledge thus improving its technological capabilities in the home country. The objective of this paper is to test empirically the presence of reverse technology transfer and its impact on the innovation capabilities in Mexican transnational corporations (MXTNCs) as a part of the emerging countries TNCs that have successfully entered to industrialized markets. Using a panel dataset of 22 MXTNCs over the period 1994-2015, the results of the econometric model demonstrate that the amount of Mexican outward FDI and the research and development (R&D) expenditure in host developed countries had a positive impact on the innovation capabilities at the firm and industry level. There is also evidence that management of acquired brands and the organizational structure of Mexican subsidiaries improved these capabilities. Implications for internationalization strategies of emerging countries corporations and future research guidelines are discussed.

Keywords: emerging countries, foreign direct investment, innovation capabilities, Mexican transnational corporations, reverse technology transfer

Procedia PDF Downloads 221

Authors: Ricardo Mendoza, Jason Briceño, Juan F. Santa, Gabriel Peluffo, Mauricio Márquez, Beatriz Cardozo, Carlos Gutiérrez

Abstract:

The most common controlled method to obtain impact strength of composites materials is performing a Charpy Impact Test which consists of a pendulum with calibrated mass and length released from a known height. In fact, composites components experience impact events in normal operations such as when a tool drops or a foreign object strikes it. These events are categorized into low velocity impact (LVI) which typically occurs at velocities below 10m/s. In this study, the major aim was to calculate the absorbed energy during the impact. Tests were performed on three types of composite panels: fiberglass laminated panels, coir fiber reinforced polyester and coir fiber reinforced polyester subjected to water immersion for 48 hours. Coir fibers were obtained in local plantations of the Caribbean coast of Colombia. They were alkali treated in 5% aqueous NaOH solution for 2h periods. Three type of shape impactors were used on drop-weight impact test including hemispherical, ogive and pointed. Failure mechanisms and failure modes of specimens were examined using an optical microscope. Results demonstrate a reduction in absorbed energy correlated with the increment of water absorption of the panels. For each level of absorbed energy, it was possible to associate a different fracture state. This study compares results of energy absorbed obtained from two impact test methods.

Keywords: coir fiber, polyester composites, low velocity impact, Charpy impact test, drop-weight impact test

Procedia PDF Downloads 448

Authors: Sarah Ryu

Abstract:

Agricultural methods and ecological approaches employed by the pre-colonial Mayans may provide valuable insights into forest management and viable alternatives for resource sustainability in the face of major deforestation across Central and South America.Using a combination of observation data collected from the modern indigenous inhabitants near Mixco in Guatemala and historical data, this study was able to create a holistic picture of how the Maya maintained their ecosystems. Surveys and observations were conducted in the field, over a period of twelve weeks across two years. Geographic and archaeological data for this area was provided by Guatemalan organizations such as the Universidad de San Carlos de Guatemala. Observations of current indigenous populations around Mixco showed that they adhered to traditional Mayan methods of agriculture, such as terrace construction and arboriculture. Rather than planting one cash crop as was done by the Spanish, indigenous peoples practice agroforestry, cultivating forests that would provide trees for construction material, wild plant foods, habitat for game, and medicinal herbs. The emphasis on biodiversity prevented deforestation and created a sustainable balance between human consumption and forest regrowth. Historical data provided by MayaSim showed that the Mayans successfully maintained their ecosystems from about 800BCE to 700CE. When the Mayans practiced natural resource conservation and cultivated a harmonious relationship with the forest around them, they were able to thrive and prosper alongside nature. Having lasted over a thousand years, the Mayan empire provides a valuable lesson in sustainability and human attitudes towards the environment.

Keywords: biodiversity, forestry, mayan, sustainability

Procedia PDF Downloads 173

Authors: Marco Antonio Lara De la Calleja, María Catalina Ovando Chico, Eduardo Lopez Ruiz

Abstract:

Community empowerment has been proved to be a key element in the solution of the food security problem. As a result of a conceptual analysis, it was found that agricultural production, economic development and governance, are the traditional basis of food security models. Although the literature points to social inclusion as an important factor for food security, no model has considered it as the basis of it. The aim of this research is to identify different dimensions that make an integral model for food security, with emphasis on community empowerment. A diagnosis was made in the study community (Tatoxcac, Zacapoaxtla, Puebla), to know the aspects that impact the level of food insecurity. With a statistical sample integrated by 200 families, the Latin American and Caribbean Food Security Scale (ELCSA) was applied, finding that: in households composed by adults and children, have moderated food insecurity, (ELCSA scale has three levels, low, moderated and high); that result is produced mainly by the economic income capacity and the diversity of the diet on its food. With that being said, a model was developed to promote food security through five dimensions: 1. Regional context of the community; 2. Structure and system of local food; 3. Health and nutrition; 4. Information and technology access; and 5. Self-awareness and empowerment. The specific actions on each axis of the model, allowed a systemic approach needed to attend food security in the community, through the empowerment of society. It is concluded that the self-awareness of local communities is an area of extreme importance, which must be taken into account for participatory schemes to improve food security. In the long term, the model requires the integrated participation of different actors, such as government, companies and universities, to solve something such vital as food security.

Keywords: community empowerment, food security, model, systemic approach

Procedia PDF Downloads 367

Authors: Diego Carrasco, Catarina Freitas, Hugo Rio Tinto, Ricardo Rio Tinto, Nuno Couto, Joaquim Gago, Carlos Carvalho

Abstract:

Introduction: Endoscopic ultrasound-guided choledochoduodenostomy (EUS-CD) to drain the gallbladder can be a palliative care procedure for non-surgical oncologic patients with cholelithiasis and cholangitis process. Case description: A 59-years old Caucasian male diagnosed with extrahepatic cholangiocarcinoma with multiple liver, lung and peritoneum metastasis, unresponsive to treatment with gemcitabine/cisplatin, presented in the institution with fever, hypotension, and severe upper right abdominal pain secondary to cholelithiasis and cholangitis process. The patient was admitted and started on large spectrum antibiotics plus fluid-challenge. Afterward, a percutaneous transhepatic biliary drainage (PTBD) was performed to drain the gallbladder. This procedure temporarily stabilized the patient. However, the definitive solution required gallbladder removal. Since the patient exhibited an advanced oncologic disease and poor response to the chemotherapy, he was not a candidate for surgical intervention. Diagnostic Pathways: A self-expanding metal stent was placed from the duodenum into the bile duct by endoscopic ultrasound-guided. The stent allowed efficient drainage of the contrast from the gallbladder at the end of the endoscopic procedure. Conclusion and Discussion: The stent allowed efficient drainage of the contrast from the gallbladder at the end of the endoscopic procedure and successfully reversed the cholangitis process. EUS-CD is an effective and safe technique and can be used as a palliative care procedure for non-surgical oncologic patients.

Keywords: palliative care, cholangiocarcinoma, choledochoduodenostomy, endoscopic ultrasound-guided

Procedia PDF Downloads 180

Authors: Hana Tadesse, Marika Grillini, Giulia Simonato, Alessandra Mondin, Giorgia Dotto, Antonio Frangipane Di Regalbono, Bersissa Kumsa, Rudi Cassini, Maria Luisa Menandro

Abstract:

Dogs are known to host several tick-borne pathogens with zoonotic potential; however, scant information is available on the epidemiology of these pathogens in low-income tropical coun- tries and in particular in sub-Saharan Africa. With the aim of investigating a wide range of tick- borne pathogens (i.e., Rickettsia spp., Anaplasma spp., Erhlichia spp., Borrelia spp., Hepatozoon spp. and Babesia spp.), 273 blood samples were collected from dogs in selected districts of Ethiopia and analyzed by real-time and/or end-point PCR. The results of the study showed that Hepatozoon canis was the most prevalent pathogen (53.8%), followed by Anaplasma phagocythophilum (7.0%), Babesia canis rossi (3.3%), Ehrlichia canis (2.6%) and Anaplasma platys (2.2%). Furthermore, five samples tested positive for Borrelia spp., identified as Borrelia afzelii (n = 3) and Borrelia burgdorferi (n = 2), and two samples for Rickettsia spp., identified as Rickettsia conorii (n = 1) and Rickettsia monacensis (n = 1). The finding of Anaplasma phagocythophilum and different species of the genera Borrelia and Rickettsia with zoonotic potential was unexpected and alarming, and calls for further investigation on the roles of dogs and on the tick, species acting as vector in this specific context. Other pathogens (Hepatozoon canis, Babaesia canis rossi, Anaplasma platys, Ehrlichia canis) are already known to have an important impact on the dogs’ health but have minor zoonotic potential as they were rarely or never reported in humans. Dogs from rural areas were found to be at higher risk for different pathogens, probably due to the presence of other wild canids in the same environment. The findings of the present study contribute to a better knowledge of the epidemiology of tick-borne pathogens, which is relevant to human and animal health.

Keywords: Dogs, Tick-borne pathogens, Africa, Ethiopia

Procedia PDF Downloads 84

Authors: Florence Ncube

Abstract:

This paper examines the military and post-military experiences of soldiers who deserted from the Rwanda Defence Force (RDF) and tried to make a living in South Africa. Because they are deserters, they try to hide their military identity, yet it is simultaneously somewhat coercively ascribed to them by the Rwandan state and can put them in potential danger. The paper attends to the constructions, experiences, practices, and subjective understanding of the deserters’ being in exile to examine how, under circumstances of perceived threat, these men navigate real or perceived state-sponsored surveillance and threat in non-military settings in South Africa where they have become potential political and disciplinary targets. To make sense of the deserters’ experiences in these circumstances, the paper stitches together a number of useful theoretical concepts, including Bourdieu’s (1992) theory of practice and Vigh’s (2009; 2018) concept of social navigation because no single approach can coherently analyze the specificity of this study. Conventional post-military literature privileges an understanding of army desertion as a malignancy and somewhat problematic. Little is known about the military and post-military experiences of deserters who believe that army desertion is in fact a building block towards achieving subjective peace, even in the context of exile. The paper argues that the presence of Rwandan state agents in South Africa strips the context of the exile of its capacity to provide the deserters with peace, safety, and security. This paper recenters army desertion in analyses of militarism, soldiering, and transition in African contexts and complicates commonsense understandings of army desertion which assume that it is entirely problematic. This paper is drawn from an ethnography conducted among 30 junior-rank Rwandan army deserters exiled in Johannesburg and Cape Town. The researcher employed life histories, in-depth interviews, and deep hangouts to collect data.

Keywords: army deserter, military, identity, exile, peacebuilding, South Africa

Procedia PDF Downloads 62

Authors: Georgi Vendramin, Aurea Lúcia, Yamamoto, Carlos Itsuo, Souza Melegari, N. Samuel

Abstract:

This article describes the development of a model that uses a method where openings are represented by single glass and double glass. The model is based on a healthy balance equations purely theoretical and empirical data. Simplified equations are derived through a synthesis of the measured data obtained from meteorological stations. The implementation of the model in a design tool integrated buildings is discussed in this article, to better punctuate the requirements of comfort and energy efficiency in architecture and engineering. Sustainability, energy efficiency, and the integration of alternative energy systems and concepts are beginning to be incorporated into designs for new buildings and renovations to existing buildings. Few means have existed to effectively validate the potential performance benefits of the design concepts. It was used a method of degree-days for an assessment of the energy performance of a building showed that the design of the architectural design should always be considered the materials used and the size of the openings. The energy performance was obtained through the model, considering the location of the building Central Park Shopping Mall, in the city of Cascavel - PR. Obtained climatic data of these locations and in a second step, it was obtained the coefficient of total heat loss in the building pre-established so evaluating the thermal comfort and energy performance. This means that the more openings in buildings in Cascavel – PR, installed to the east side, they may be higher because the glass added to the geometry of architectural spaces will cause the environment conserve energy.

Keywords: sustainable design, energy modeling, design validation, degree-days methods

Procedia PDF Downloads 410

Authors: Carlos Alberto Ríos Reyes

Abstract:

Traditionally, clays have been considered as one of the main problems in the flow of fluids in hydrocarbon reservoirs. However, there is not known the significance of zeolites formed from the reactivity of clays and their effect not only on the costs of operations carried out by the oil industry in the world but also on production. The present work focused on understanding the interaction between clay minerals with brines and alkaline solutions used in the oil industry. For this, a comparative study was conducted where the reaction of sedimentary rocks under laboratory conditions was examined. Original and treated rocks were examined by X-ray powder diffraction (XRPD) and Scanning Electron Microscopy (SEM) to determine the changes that these rocks underwent upon contact with fluids of variable chemical composition. As a result, zeolite Linde Type A (LTA), sodalite (SOD), and cancrinite (CAN) can be formed after experimental work, which coincided with the dissolution of kaolinite and smectite. Results reveal that the Oil Industry should invest efforts and focus its gaze to understand at the pore scale the problem that could arise as a consequence of the clay-fluid interaction in hydrocarbon reservoir rocks due to the presence of clays in their porous system, as well as the formation of zeolites, which are better hydrocarbon absorbents. These issues could be generating losses in world production. We conclude that there is a critical situation that may be occurring in the stimulation of hydrocarbon reservoirs, where real solutions are necessary not only for the formulation of more efficient and effective injection fluids but also to contribute to the improvement of production and avoid considerable losses in operating costs.

Keywords: clay minerals, zeolites, rock-fluid interaction, experimental work, reactivity

Procedia PDF Downloads 76

Authors: Antonio Monteiro, Jorge Azevedo, Severiano Silva, Alfredo Teixeira

Abstract:

The objective of this study was to compare the carcass and in vivo real-time ultrasound measurements (RTU) and their capacity to predict the composition of Serrana goats up to 40% of maturity. Twenty one females (11.1 ± 3.97 kg) and Twenty one males (15.6 ± 5.38 kg) were utilized to made in vivo measurements with a 5 MHz probe (ALOKA 500V scanner) at the 9th-10th, 10th-11th thoracic vertebrae (uT910 and uT1011, respectively), at the 1st- 2nd, 3rd-4th, and 4th-5th lumbar vertebrae (uL12, ul34 and uL45, respectively) and also at the 3rd-4th sternebrae (EEST). It was recorded the images of RTU measurements of Longissimus thoracis et lumborum muscle (LTL) depth (EM), width (LM), perimeter (PM), area (AM) and subcutaneous fat thickness (SFD) above the LTL, as well as the depth of tissues of the sternum (EEST) between the 3rd-4th sternebrae. All RTU images were analyzed using the ImageJ software. After slaughter, the carcasses were stored at 4 ºC for 24 h. After this period the carcasses were divided and the left half was entirely dissected into muscle, dissected fat (subcutaneous fat plus intermuscular fat) and bone. Prior to the dissection measurements equivalent to those obtained in vivo with RTU were recorded. Using the Statistica 5, correlation and regression analyses were performed. The prediction of carcass composition was achieved by stepwise regression procedure, with live weight and RTU measurements with and without transformation of variables to the same dimension. The RTU and carcass measurements, except for SFD measurements, showed high correlation (r > 0.60, P < 0.001). The RTU measurements and the live weight, showed ability to predict carcass composition on muscle (R2 = 0.99, P < 0.001), subcutaneous fat (R2 = 0.41, P < 0.001), intermuscular fat (R2 = 0.84, P < 0.001), dissected fat (R2 = 0.71, P < 0.001) and bone (R2 = 0.94, P < 0.001). The transformation of variables allowed a slight increase of precision, but with the increase in the number of variables, with the exception of subcutaneous fat prediction. In vivo measurements by RTU can be applied to predict kid goat carcass composition, from 5 measurements of RTU and the live weight.

Keywords: carcass, goats, real time, ultrasound

Procedia PDF Downloads 256

Authors: Rodrigo T. Sepulveda-Hirose, Ana B. Carrera-Aguilar, Magnolia G. Martinez-Rivera, Pablo de J. Angeles-Salto, Carlos Herrera-Ventosa

Abstract:

In order to diminish health risks, it is of major importance to monitor air quality. However, this process is accompanied by the high costs of physical and human resources. In this context, this research is carried out with the main objective of developing a predictive model for concentrations of inhalable particles (PM10-2.5) using remote sensing. To develop the model, satellite images, mainly from Landsat 8, of the Mexico City’s Metropolitan Area were used. Using historical PM10 and PM2.5 measurements of the RAMA (Automatic Environmental Monitoring Network of Mexico City) and through the processing of the available satellite images, a preliminary model was generated in which it was possible to observe critical opportunity areas that will allow the generation of a robust model. Through the preliminary model applied to the scenes of Mexico City, three areas were identified that cause great interest due to the presumed high concentration of PM; the zones are those that present high plant density, bodies of water and soil without constructions or vegetation. To date, work continues on this line to improve the preliminary model that has been proposed. In addition, a brief analysis was made of six models, presented in articles developed in different parts of the world, this in order to visualize the optimal bands for the generation of a suitable model for Mexico City. It was found that infrared bands have helped to model in other cities, but the effectiveness that these bands could provide for the geographic and climatic conditions of Mexico City is still being evaluated.

Keywords: air quality, modeling pollution, particulate matter, remote sensing

Procedia PDF Downloads 149

Authors: Todd Pennington, Carol Wilkinson, Keven Prusak

Abstract:

Traditional models of student teaching practices typically involve the placement of a student teacher with an experienced mentor teacher. However, due to the ever-decreasing number of quality placements, an alternative triad approach is the paired placement of student teachers with one mentor teacher in a community of practice. This study examined the paired-placement of student teachers in physical education to determine the benefits and drawbacks after a 14-week student teaching experience. PETE students (N = 22) at a university in the United States were assigned to work in a triad with a student teaching partner and a mentor teacher, making up eleven triads for the semester. The one exception was a pair that worked for seven weeks at an elementary school and then for seven weeks at a junior high school, thus having two mentor teachers and participating in two triads. A total of 12 mentor teachers participated in the study. All student teachers and mentor teachers volunteered and agreed to participate. The student teaching experience was structured so that students engaged in: (a) individual teaching (one teaching the lesson with the other observing), (b) co-planning, and (c) peer coaching. All students and mentor teachers were interviewed at the conclusion of the experience. Using interview data, field notes, and email response data, the qualitative data was analyzed using the constant comparative method. The benefits of the paired placement experience emerged into three categories (a) quality feedback, (b) support, and (c) collaboration. The drawbacks emerged into four categories (a) unrealistic experience, (b) laziness in preparation, (c) lack of quality feedback, and (d) personality mismatch. Recommendations include: providing in-service training prior to student teaching to optimize the triad experience, ongoing seminars throughout the experience specifically designed for triads, and a hybrid model of paired placement for the first half of student teaching followed by solo student teaching for the second half of the experience.

Keywords: community of practice, paired placement, physical education, student teaching

Procedia PDF Downloads 394

Authors: Fernández-Brito David, Lopez-Medina Javier Alonso, Murillo-Bracamontes Eduardo Antonio, Palomino-Ovando Martha Alicia, Gervacio-Arciniega José Juan

Abstract:

Magnetic Force Microscopy (MFM) is an Atomic Force Microscopy (AFM) technique that characterizes, at a nanometric scale, the magnetic properties of ferromagnetic materials. Conventional MFM works by scanning in two different AFM modes. The first one is tapping mode, in which the cantilever has short-range force interactions with the sample, with the purpose to obtain the topography. Then, the lift AFM mode starts, raising the cantilever to maintain a fixed distance between the tip and the surface of the sample, only interacting with the magnetic field forces of the sample, which are long-ranged. In recent years, there have been attempts to improve the MFM technique. Bimodal MFM was first theoretically developed and later experimentally proven. In bimodal MFM, the AFM internal piezoelectric is used to cause the cantilever oscillations in two resonance modes simultaneously, the first mode detects the topography, while the second is more sensitive to the magnetic forces between the tip and the sample. However, it has been proven that the cantilever vibrations induced by the internal AFM piezoelectric ceramic are not optimal, affecting the bimodal MFM characterizations. Moreover, the Secondary Resonance Magnetic Force Microscopy (SR-MFM) was developed. In this technique, a coil located below the sample generates an external magnetic field. This alternating magnetic field excites the cantilever at a second frequency to apply the Bimodal MFM mode. Nonetheless, for ferromagnetic materials with a low coercive field, the external field used in SR-MFM technique can modify the magnetic domains of the sample. In this work, a Hybrid Bimodal MFM (HB-MFM) technique is proposed. In HB-MFM, the bimodal MFM is used, but the first resonance frequency of the cantilever is induced by the magnetic field of the ferromagnetic sample due to its vibrations caused by a piezoelectric element placed under the sample. The advantages of this new technique are demonstrated through the preliminary results obtained by HB-MFM on a hard disk sample. Additionally, traditional two pass MFM and HB-MFM measurements were compared.

Keywords: magnetic force microscopy, atomic force microscopy, magnetism, bimodal MFM

Procedia PDF Downloads 64

Authors: Marta E. Hernandez-Caballero, Veronica Borgonio-Cuadra, Antonio Miranda-Duarte, Xochitl Rojas-Toledo, Normand Garcia-Hernandez, Maura Cardenas-Garcia, Teresa Abad-Camacho

Abstract:

Breast cancer (BC) is the most common tumor in women over the world. DNA methylation is an epigenetic modification critical in CpG sites, aberrant methylation of CpG islands in promoters is a hallmark of cancer. So, gene expression can be regulated by alterations in DNA methylation. In cell lines DACT2 gene reduces the growth and migration of tumor cells by its participation in the suppression of TGFb/SMAD2/3. PHF20L1 is involved in histone acetylation therefore, it regulates transcription. Our aim was to analyze the methylation status of the DACT2 and PHF20L1 promoter regions in tumoral and healthy mammary tissue from women with BC in different progression states. The study included 77 patients from Centro Medico Nacional La Raza in Mexico City. After identifying a CpG island in DACT2 and PHF20L1 promoters, DNA methylation status was analyzed through sodium bisulfite with subsequent amplification using methylation-specific PCR. Results revealed no changes in methylation status of PHF20L1 and cancer stages (II y III) or in comparison to healthy tissues, it was demethylated. DACT2 promoter methylation was no significant between tumoral stages (II, P = 0.37; III, P = 0.17) or with healthy tissue. Previous data reported DACT2 methylated in nasopharyngeal carcinoma but in this study promoter methylation was not observed. PHF20L1 protein contains N-terminal Tudor and C-terminal plant homeodomain domains, it has been suggested that can stabilize DNMT1 regulating DNA methylation, therefore, was associated with poor prognostic in BC. We found no evidence of methylation in patients and controls in PHF20L1 promoter, so its association with BC may have no direct relation with promoter methylation. More studies including other methylation sites in these genes in BC are necessary.

Keywords: bisulfite conversion, breast cancer, DACT2, DNA methylation, PHF20L1, tumoral status

Procedia PDF Downloads 294

Authors: Anyi Katherine Garzon Robles, Luis Carlos Gomez Florez

Abstract:

Since the advent of the Internet, the use of Information Technologies (IT) has increased exponentially. The field of informatics and telecommunications has put on the table countless possibilities for the development of different socio-economic activities, promoting a change of social paradigm and the emergence of the so-called information and knowledge society. For more than a decade, the Colombian government has been working on the incorporation of IT into the public sector through an e-government strategy. However, to date, many technological gaps has not yet been identified in the country to our knowledge, especially in rural areas and far from large cities, where factors such as low investment and the expansion of the armed conflict have led to economic and technological stagnation. This paper presents the research results obtained from the execution of a research project, which was approach from a qualitative approach and a methodological design of a participatory action research type. This design consists of nine fundamental stages divided into four work cycles. For which different strategies for data collection and analysis were established. From which, a methodology was obtained for the identification of technological gaps and the measurement of the level of technological acceptance in the rural sector, based on the TAM (Technology Acceptance Model) model, as a previous activity to the development of IT solutions framed in the e-government strategy in Colombia. The result of this research work represents a contribution from academia for the improvement of the country's technological development and a guide for the proper planning of IT solutions aimed at promoting a close relationship between government and citizens.

Keywords: E-government, knowledge society, level of technological acceptance, technological gaps, technology acceptance model

Procedia PDF Downloads 232

Authors: Nessa-Amie T. Peñaflor, Antonio Cinto

Abstract:

This is a descriptive research on the level of math anxiety and mathematics misconceptions in algebra. This research is composed of four parts: (1) analysis of the level of anxiety of the respondents; (2) analysis of the common mathematical misconceptions in algebra; (3) relationship of socio-demographic profile in math anxiety and mathematical misconceptions and (4) analysis of the relationship of math anxiety and misconceptions in algebra. Through the demographic profile questionnaire it was found out that most of the respondents were female. Majority had ages that ranged from 13-15. Most of them had parents who finished secondary education. The biggest portion of Grade Seven students where from families with annual family income ranging from PhP 100, 000 to PhP 299, 999. Most of them came from public school. Mathematics Anxiety Scale for Secondary and Senior Secondary School Students (MAS) and set of 10 open-ended algebraic expressions and polynomials were also administered to determine the anxiety level and the common misconceptions in algebra. Data analysis revealed that respondents had high anxiety in mathematics. Likewise, the common mathematical misconceptions of the Grade Seven students were: combining unlike terms; multiplying the base and exponents; regarding the variable x as 0; squaring the first and second terms only in product of two binomials; wrong meaning attached to brackets; writing the terms next to each other but not simplifying in using the FOIL Method; writing the literal coefficient even if the numerical coefficient is 0; and dividing the denominator by the numerator when the numerical coefficient in the numerator is smaller than the numerical coefficient of the denominator. Results of the study show that the socio-demographic characteristics were not related to mathematics anxiety and misconceptions. Furthermore, students from higher section had high anxiety than those students on the lower section. Thus, belonging to higher or lower section may affect the mathematical misconceptions of the respondents.

Keywords: algebra, grade 7 math, math anxiety, math misconceptions

Procedia PDF Downloads 407

Authors: Swarnapriya Thiyagarajan, Modesto Antonio Sosa Aquino, Miguel Vallejo Hernandez, Senthilkumar Kalaiselvan Dhivyaraj, Jayaramakrishnan Velusamy

Abstract:

In this paper the lithium tetra borate (Li2B4O7) was prepared by used water/solution assisted synthesis method. Once finished the synthesization, Copper (Cu) were used to doping material with Li2B4O7 in order to enhance its thermo luminescent properties. The heating temperature parameters were 750°C for 2 hr and 150°C for 2hr. The samples produced by water assisted method were doped at different doping percentage (0.02%, 0.04%, 0.06%, 0.08%, 0.12%, 0.5%, 0.1%, and 1%) of Cu.The characteristics and identification of Li2B4O7 (undoped and doped) were determined in four tests. They are X-ray diffraction (XRD), Scanning electron microscope (SEM), Photoluminescence (PL), Ultra violet visible spectroscopy (UV Vis). As it is evidence from the XRD and SEM results the obtained Li2B4O7 and Li2B4O7 doping with Cu was confirmed and also confirmed the chemical compositition and their morphologies. The obtained lithium tetraborate XRD pattern result was verified with the reference data of lithium tetraborate with tetragonal structure from JCPDS. The glow curves of Li2B4O7 and Li2B4O7 : Cu were obtained by thermo luminescence (TLD) reader (Harshaw 3500). The pellets were irradiated with different kind of dose (58mGy, 100mGy, 500mGy, and 945mGy) by using an X-ray source. Finally this energy response was also compared with TLD100. The order of kinetics (b), frequency factor (S) and activation energy (E) or the trapping parameters were calculated using peak shape method. Especially Li2B4O7: Cu (0.1%) presents good glow curve in all kind of doses. The experimental results showed that this Li2B4O7: Cu could have good potential applications in radiation dosimetry. The main purpose of this paper is to determine the effect of synthesis on the TL properties of doped lithium tetra borate Li2B4O7.

Keywords: dosimetry, irradiation, lithium tetraborate, thermoluminescence

Procedia PDF Downloads 269

Authors: Sofia G. Meirinho, Luis G. Dias, António M. Peres, Lígia R. Rodrigues

Abstract:

The emerging development of electrochemical aptasen sors has enabled the easy and fast detection of protein biomarkers in standard and real samples. Biomarkers are produced by body organs or tumours and provide a measure of antigens on cell surfaces. When detected in high amounts in blood, they can be suggestive of tumour activity. These biomarkers are more often used to evaluate treatment effects or to assess the potential for metastatic disease in patients with established disease. Osteopontin (OPN) is a protein found in all body fluids and constitutes a possible biomarker because its overexpression has been related with breast cancer evolution and metastasis. Currently, biomarkers are commonly used for the development of diagnostic methods, allowing the detection of the disease in its initial stages. A previously described RNA aptamer was used in the current work to develop a simple and sensitive electrochemical aptasensor with high affinity for human OPN. The RNA aptamer was biotinylated and immobilized on a gold electrode by avidin-biotin interaction. The electrochemical signal generated from the aptamer–target molecule interaction was monitored electrochemically using cyclic voltammetry in the presence of [Fe (CN) 6]−3/− as a redox probe. The signal observed showed a current decrease due to the binding of OPN. The preliminary results showed that this aptasensor enables the detection of OPN in standard solutions, showing good selectivity towards the target in the presence of others interfering proteins such as bovine OPN and bovine serum albumin. The results gathered in the current work suggest that the proposed electrochemical aptasensor is a simple and sensitive detection tool for human OPN and so, may have future applications in cancer disease monitoring.

Keywords: osteopontin, aptamer, aptasensor, screen-printed electrode, cyclic voltammetry

Procedia PDF Downloads 424

Authors: Camarena Rodriguez C. S., Portocarrero Bonifaz A., Palma Esparza R., Romero Carlos N. A.

Abstract:

Adobe is a construction material that fulfills the same function as a conventional brick. Widely used since ancient times, it is present in an appreciable percentage of buildings in Latin America. Adobe is a mixture of clay and sand. The interest in the study of the properties of this material arises due to its presence in the infrastructure of hospital´s radiological services, located in places with low economic resources, for the attenuation of radiation. Some materials such as lead and concrete are the most used for shielding and are widely studied in the literature. The present study will determine the mass attenuation coefficient of Adobe. The minimum required thicknesses for the primary and secondary barriers will be estimated for the shielding of radiological facilities where conventional and dental X-rays are performed. For the experimental procedure, an X-ray source emitted direct radiation towards different thicknesses of an Adobe barrier, and a detector was placed on the other side. For this purpose, an UNFORS Xi solid state detector was used, which collected information on the difference of radiation intensity. The initial parameters of the exposure started at 45 kV; and then the tube tension was varied in increments of 5 kV, reaching a maximum of 125 kV. The X-Ray tube was positioned at a distance of 0.5 m from the surface of the Adobe bricks, and the collimation of the radiation beam was set for an area of 0.15 m x 0.15 m. Finally, mathematical methods were applied to determine the mass attenuation coefficient for different energy ranges. In conclusion, the mass attenuation coefficient for Adobe was determined and the approximate thicknesses of the most common Adobe barriers in the hospital buildings were calculated for their later application in the radiological protection.

Keywords: Adobe, attenuation coefficient, radiological protection, shielding, x-rays

Procedia PDF Downloads 154