Search results for: Muhammad R. Ahmed

Authors: Shegufta Zahan, Muhammad A. Zahin, Muhammad M. Hossain, Raquib Ahsan

Abstract:

Rice Husk Ash (RHA) is one of the agricultural waste byproducts available widely in the world and contains a large amount of silica. In Bangladesh, stones cannot be used as coarse aggregate in infrastructure works as they are not available and need to be imported from abroad. As a result, bricks are mostly used as coarse aggregates in concrete as they are cheaper and easily produced here. Clay is the raw material for producing brick. Due to rapid urban growth and the industrial revolution, demand for brick is increasing, which led to a decrease in the topsoil. This study aims to produce lightweight block aggregates with sufficient strength utilizing RHA at low cost and use them as an ingredient of concrete. RHA, because of its pozzolanic behavior, can be utilized to produce better quality block aggregates at lower cost, replacing clay content in the bricks. The whole study can be divided into three parts. In the first part, characterization tests on RHA and clay were performed to determine their properties. Six different types of RHA from different mills were characterized by XRD and SEM analysis. Their fineness was determined by conducting a fineness test. The result of XRD confirmed the amorphous state of RHA. The characterization test for clay identifies the sample as “silty clay” with a specific gravity of 2.59 and 14% optimum moisture content. In the second part, blocks were produced with six different types of RHA with different combinations by volume with clay. Then mixtures were manually compacted in molds before subjecting them to oven drying at 120 °C for 7 days. After that, dried blocks were placed in a furnace at 1200 °C to produce ultimate blocks. Loss on ignition test, apparent density test, crushing strength test, efflorescence test, and absorption test were conducted on the blocks to compare their performance with the bricks. For 40% of RHA, the crushing strength result was found 60 MPa, where crushing strength for brick was observed 48.1 MPa. In the third part, the crushed blocks were used as coarse aggregate in concrete cylinders and compared them with brick concrete cylinders. Specimens were cured for 7 days and 28 days. The highest compressive strength of block cylinders for 7 days curing was calculated as 26.1 MPa, whereas, for 28 days curing, it was found 34 MPa. On the other hand, for brick cylinders, the value of compressing strength of 7 days and 28 days curing was observed as 20 MPa and 30 MPa, respectively. These research findings can help with the increasing demand for topsoil of the earth, and also turn a waste product into a valuable one.

Keywords: characterization, furnace, pozzolanic behavior, rice husk ash

Procedia PDF Downloads 86

Authors: Ahmad Alwosheel, Ahmed Alqaraawi

Abstract:

This work proposes a new speaker segmentation approach for two speakers. It is an online approach that does not require a prior information about speaker models. It has two phases, a conventional approach such as unsupervised BIC-based is utilized in the first phase to detect speaker changes and train a Neural Network, while in the second phase, the output trained parameters from the Neural Network are used to predict next incoming audio stream. Using this approach, a comparable accuracy to similar BIC-based approaches is achieved with a significant improvement in terms of computation time.

Keywords: artificial neural network, diarization, speaker indexing, speaker segmentation

Procedia PDF Downloads 479

Authors: Rania F. Ahmed, Sally A. El Awdan, Gehad A. Abdel Jaleel, Dalia O. Saleh, Omar A. H. Ahmed-Farid

Abstract:

The metabolic syndrome is an important public health concern often related to obesity, improper diet, and sedentary lifestyles and can predispose individuals to the development of many dangerous health conditions, disability and early death. This research aimed to investigate the efficacy of resveratrol (RSV) to reverse the neuro-complications associated with metabolic syndrome experimentally-induced in rats using an eight weeks high fat, high fructose diet (HFHF) model. The corresponding drug treatments were administered orally during the last 10 days of the diet. Behavioural tests namely the open field test (OFT) and the forced swimming test (FST) were conducted. Brain levels of monoamines viz. serotonin, norepinephrine and dopamine as well as their metabolites were assessed. 8-hydroxyguanosine (8-OHDG) as an indicative of DNA-fragmentation, nitric oxide (NOx) and tumor necrosis factor-α (TNF- α) were estimated. Finally, brain antioxidant parameters namely malondialdehyde (MDA), reduced and oxidized glutathione (GSH, GSSG) were evaluated. HFHF-induced metabolic syndrome resulted in decreased activity in the OFT and increased immobility duration in the FST. Furthermore, HFHF-induced metabolic syndrome lead to a significant increase in brain monoamines turn over as well as elevation in 8-OHDG, NOx, TNF- α, MDA and GSSG; and reduction in GSH. Ten days daily treatment with RSV (20 and 40 mg/kg p.o) dose dependently increased activity in the OFT and decreased immobility duration in the FST. Moreover, RSV normalized brain monoamines contents, reduced 8-OHDG, NOx, TNF- α, MDA and GSSG; and elevated GSH. In conclusion, we can say that RSV showed neuro-protective properties against HFHF-induced metabolic syndrome represented by monoamines preservation, prevention of neurodegeneration, anti-inflammatory and antioxidant potentials and could be recommended as a beneficial daily dietary supplement to treat the neuronal side effects associated with HFHF-induced metabolic syndrome.

Keywords: antioxidants, DNA-fragmentation, forced swimming test, HFHF-induced metabolic syndrome, monoamines, nitric oxide (NOx), open field, resveratrol, tumor necrosis factor-α (TNF- α), 8-hydroxyguanosine (8-OHDG)

Procedia PDF Downloads 257

Authors: Majed Ahmed Alfayad

Abstract:

Technology is now present in almost all areas and practices globally, and this has led governments around the world to adopt technology in the public sector. Therefore, electronic government has been introduced as a means of the automation of government services. New technologies and trends appear every single day, and governments need to meet the citizen’s requirements and expectations in order to succeed in the E-Government program. This research investigates the potential of mobile government as an enhancement force for the E-Government project in the Kingdom of Saudi Arabia, where the usage of mobile technology is coming to be favoured by citizens. Qualitative methodology has been adopted in this study for the data collection and analysis, and in particular the grounded theory approach.

Keywords: e-government, e-participation, m-government, mobile technology

Procedia PDF Downloads 309

Authors: Ahmed I. Raheem

Abstract:

In this thesis, stratified and stratified wavy flow regimes have been investigated numerically for the oil (1.57 mPa s viscosity and 780 kg/m3 density) and water twophase flow in small and large horizontal steel pipes with a diameter between 0.0254 to 0.508 m by ANSYS Fluent software. Volume of fluid (VOF) with two phases flows using two equations family models (Realizable k-

Keywords: CFD, two-phase flow, pressure gradient, volume of fluid, large diameter, horizontal pipe, oil-water stratified and stratified wavy flow

Procedia PDF Downloads 413

Authors: Muhammad Zeeshan, Rabia Nazir, Lubna Tahir

Abstract:

Low cost filter based on iron doped zeolite (Fe-Z) and pottery clay was developed for an effective and efficient treatment of the drinking water contaminated with microbes. Fe-Z was characterized using powder XRD, SEM and EDX and shown to have average particle size of 49 nm with spongy appearance. The simulated samples of water self-contaminated with six microbes (S. typhi, B. subtilus, E. coli, S. aures, K. pneumoniae, and P. aeruginosa) after treatment with Fe-Z indicated effective removal of all the microbes in less than 30 min. Equally good results were obtained when actual drinking water samples, totally unfit for human consumption, were treated with Fe-Z.

Keywords: iron doped zeolite, biological and chemical treatment, drinking water

Procedia PDF Downloads 423

Authors: Imran Muhammad

Abstract:

The main cause of infectious disease in the modern world is Mycobacterium Tuberculosis (MT). To combat tuberculosis, new and efficient drugs are an urgent need in the modern world. Schif bases are potent for their biological pharmacophore activity. Thus we selected different Vanillin-based Schiff bases for their binding activity against target enzymes of Mycobacterium tuberculosis that is (DprE1 (decaprenyl phosphoryl-β-D-ribose 2′-epimerase), and DNA gyrase subunit-A), using molecular docking. We evaluate the inhibition potential, interaction, and binding mode of these compounds with the target enzymes.

Keywords: schiff bases, tuberculosis, DNA gyrase, DprE1, docking

Procedia PDF Downloads 55

Authors: Muhammad Rafiq, Lamae Zulfiqar, Nazish Idrees Chaudhary

Abstract:

A growing number of research focuses on healthy and unhealthy eating behaviors and their impact on health. It was intended to study the Islamic point of view on eating behavior, its impact on mental health and preventative strategies in the light of the Quran and Sunnah. Different articles and Islamic sayings related to eating behaviors and mental health were reviewed in detail. It was also revealed scientifically and through Islamic point of view that appropriate quantity, quality and timings of food have positive effects on mental health. Therefore, a 3Rs model of eating behaviors has been proposed.

Keywords: food intake, mental health, quality of food, quantity of food

Procedia PDF Downloads 215

Authors: Shamila Ahmed

Abstract:

The paper examines how the fluidity between the local level and the global level is an intrinsic feature of new terrorism. Through using cosmopolitanism, the narratives of the two opposing sides of ISIS and the ‘war on terrorism’ response are explored. It is demonstrated how the fluidity between these levels facilitates the radicalisation process through exploring how groups such as ISIS highlight the perceived injustices against Muslims locally and globally and therefore exploit the globalisation process which has reduced the space between these levels. Similarly, it is argued that the ‘war on terror’ involves the intersection of fear, security, threat, risk and social control as features of both the international ‘war on terror’ and intra state policies.

Keywords: terrorism, war on terror, cosmopolitanism, global level terrorism

Procedia PDF Downloads 566

Authors: Muhammad Farhan Saeed, Waheed Aslam Khan, Muhammad Nadeem, Iftikhar Ahmad, Zakir Ali

Abstract:

Milk is an important and fundamental nutrition source of human diet. In Pakistan, the milk used by the consumer is of low quality and is often contaminated due to the lack of quality controls. Mycotoxins produced from molds which contaminate the agriculture commodities of animal feed. Mycotoxins are poisons which affect the animals when they consume contaminated feeds. Aflatoxin AFM1 is naturally occurring form of mycotoxins in milk which is carcinogenic. To assess public awareness regarding milk Aflatoxin contamination, a population-based survey using a questionnaire was carried out from general public and from farmers of both rural and urban areas. It was revealed from the data that people of rural area were more satisfied about quality of available milk but the awareness level about milk contamination was found lower in both areas. Total 297 samples of milk were collected from rural (n=156) and urban (n=141) areas of district Vehari during June-July 2015. Milk samples were collected from three different point sources; farmer, milkman and milkshop. These point sources had three types of dairy milk including cow milk, buffalo milk and mixed milk. After performing ELISA test 18 samples with positive ELISA results were maintain per source for further analysis for aflatoxin M1 (AFM1) by High Performance Liquid Chromatography (HPLC). Higher percentages of samples were found exceeding the permissible limit for urban area. In rural area about 15% samples and from urban area about 35% samples were exceeded the permissible limit of AFM1 with 0.05µg/kg set by European Union. From urban areas about 55% of buffalo, 33% of cows and 17% of mixed milk samples were exceeded the permissible AFM1 level as compared with 17%, 11% and 17% for milk samples from rural areas respectively. Samples from urban areas 33%, 44% and 28% were exceeded the permissible AFM1 level for farmer, milkman and of milk shop respectively as compared with 28% and 17% of farmer and milkman’s samples from rural areas respectively. The presence of AFM1 in milk samples demands the implementation of strict regulations and also urges the need for continuous monitoring of milk and milk products in order to minimize the health hazards. Regulations regarding aflatoxins contamination and adulteration should be strictly imposed to prevent health problems related to milk quality. Permissible limits for aflatoxin should be enforced strongly in Pakistan so that economic loss due to aflatoxin contamination can be reduced.

Keywords: Vehari, aflatoxins AFM1, milk, HPLC

Procedia PDF Downloads 339

Authors: Samia Moulebhar, Chahrazed Bendenia, Souhila Bendenia, Hanaa Merad-dib, Sarra Merabet, Sid Ahmed Khantar, Baghdad Hadri

Abstract:

The photovoltaic solar field is today experiencing exponential advancement with the exploitation of new technological sectors of nanoparticles, namely the field of solar cells based on organic polymer materials. These cells are flexible, easy to process and low cost. This work includes a presentation of the conjugated polymer materials used in the design of photovoltaic technology devices while determining their properties and then the models used for the modeling of thin film photovoltaic cells heterojunction.

Keywords: photovoltaic, cells, nanoparticles, organic

Procedia PDF Downloads 53

Authors: Tarek Ninouh, Ahmed Rouili

Abstract:

The Roman paths or roads offer a very interesting archaeological material, because they allow us to understand the history of human settlement and are also factors that increase territorial identity. Roman roads are one of the hallmarks of the Roman empire, which extends to North Africa. The objective of this investigation is to attract the attention of researchers to the importance of Roman roads and paths, which are found in Algeria, according to the quality of the materials and techniques used in this period of our history, and to encourage other decision makers to protect and enhance these routes because the current urbanization, intensive agricultural practices, or simply forgotten, decreases the sustainability of this important historical heritage.

Keywords: Roman paths, quality of materials, property, valuation

Procedia PDF Downloads 408

Authors: Ahmed AlNouss, Salim Ahmed

Abstract:

Process control refers to the techniques to control the variables in a process in order to maintain them at their desired values. Advanced process control (APC) is a broad term within the domain of control where it refers to different kinds of process control and control related tools, for example, model predictive control (MPC), statistical process control (SPC), fault detection and classification (FDC) and performance assessment. APC is often used for solving multivariable control problems and model predictive control (MPC) is one of only a few advanced control methods used successfully in industrial control applications. Advanced control is expected to bring many benefits to the plant operation; however, the extent of the benefits is plant specific and the application needs a large investment. This requires an analysis of the expected benefits before the implementation of the control. In a real plant simulation studies are carried out along with some experimentation to determine the improvement in the performance of the plant due to advanced control. In this research, such an exercise is undertaken to realize the needs of APC application. The main objectives of the paper are as follows: (1) To apply MPC to a number of simulations set up to realize the need of MPC by comparing its performance with that of proportional integral derivatives (PID) controllers. (2) To study the effect of controller parameters on control performance. (3) To develop appropriate performance index (PI) to compare the performance of different controller and develop novel idea to present tuning map of a controller. These objectives were achieved by applying PID controller and a special type of MPC which is dynamic matrix control (DMC) on the multi-tanks process simulated in loop-pro. Then the controller performance has been evaluated by changing the controller parameters. This performance was based on special indices related to the difference between set point and process variable in order to compare the both controllers. The same principle was applied for continuous stirred tank heater (CSTH) and continuous stirred tank reactor (CSTR) processes simulated in Matlab. However, in these processes some developed programs were written to evaluate the performance of the PID and MPC controllers. Finally these performance indices along with their controller parameters were plotted using special program called Sigmaplot. As a result, the improvement in the performance of the control loops was quantified using relevant indices to justify the need and importance of advanced process control. Also, it has been approved that, by using appropriate indices, predictive controller can improve the performance of the control loop significantly.

Keywords: advanced process control (APC), control loop, model predictive control (MPC), proportional integral derivatives (PID), performance indices (PI)

Procedia PDF Downloads 391

Authors: Sherif O. Zain Elabideen, Ahmed A. Helal, Ibrahim F. El-Arabawy

Abstract:

Due to the drastic increase of the wind turbines installed capacity; the grid codes are increasing the restrictions aiming to treat the wind turbines like other conventional sources sooner. In this paper, an intensive review has been presented for different techniques used to add low voltage ride through capability to Doubly Fed Induction Generator (DFIG) wind turbine. A system model with 1.5 MW DFIG wind turbine is constructed and simulated using MATLAB/SIMULINK to explore the effectiveness of the reviewed techniques.

Keywords: DFIG, grid side converters, low voltage ride through, wind turbine

Procedia PDF Downloads 403

Authors: Ahmed Machmoum, Malika El Kyal

Abstract:

We consider iterative parallel multi-splitting method for differential algebraic equations. The main feature of the proposed idea is to use the asynchronous form. We prove that the multi-splitting technique can effectively accelerate the convergent performance of the iterative process. The main characteristic of an asynchronous mode is that the local algorithm not have to wait at predetermined messages to become available. We allow some processors to communicate more frequently than others, and we allow the communication delays tobe substantial and unpredictable. Note that synchronous algorithms in the computer science sense are particular cases of our formulation of asynchronous one.

Keywords: computer, multi-splitting methods, asynchronous mode, differential algebraic systems

Procedia PDF Downloads 527

Authors: Muhammad Tahir, Mushtaq Muhammad

Abstract:

Capital structure is one of the key decisions taken by the financial managers. This study aims to investigate the factors influencing capital structure decision in Oil and Gas industry of Pakistan using secondary data from published annual reports of listed Oil and Gas Companies of Pakistan. This study covers the time-period from 2008-2014. Capital structure can be affected by profitability, firm size, growth opportunities, dividend payout, liquidity, business risk, and ownership structure. Panel data technique with Ordinary least square (OLS) regression model has been used to find the impact of set of explanatory variables on the capital structure using the Stata. OLS regression results suggest that dividend payout, firm size and government ownership have the most significant impact on financial leverage. Dividend payout and government ownership are found to have significant negative association with financial leverage however firm size indicated positive relationship with financial leverage. Other variables having significant link with financial leverage includes growth opportunities, liquidity and business risk. Results reveal significant positive association between growth opportunities and financial leverage whereas liquidity and business risk are negatively correlated with financial leverage. Profitability and managerial ownership exhibited insignificant relationship with financial leverage. This study contributes to existing Managerial Finance literature with certain managerial implications. Academically, this research study describes the factors affecting capital structure decision of Oil and Gas Companies in Pakistan and adds latest empirical evidence to existing financial literature in Pakistan. Researchers have studies capital structure in Pakistan in general and industry at specific, nevertheless still there is limited literature on this issue. This study will be an attempt to fill this gap in the academic literature. This study has practical implication on both firm level and individual investor/ lenders level. Results of this study can be useful for investors/ lenders in making investment and lending decisions. Further, results of this study can be useful for financial managers to frame optimal capital structure keeping in consideration the factors that can affect capital structure decision as revealed by this study. These results will help financial managers to decide whether to issue stock or issue debt for future investment projects.

Keywords: capital structure, multicollinearity, ordinary least square (OLS), panel data

Procedia PDF Downloads 273

Authors: Muhammad Rizwan Akram, Saim Raza, Hamza Hanif Chauhan

Abstract:

This paper describes the aim of research to evaluate the performance of ordinary Portland concretes containing cement replacement materials in both binary and ternary system. Blocks of concrete were prepared to have a constant water-binder ratio of 0.30. The test variables included the type and the amount of the supplementary cementious materials (SCMs) such as class of Silica Fume (SF) and ground granulated blast furnace slag (GGBS). Portland cement was replaced with Silica Fume (SF) upto 7.5% and GGBS up to a level of 50%. Then physical properties are assessed from the compressive strength and permeability tests.

Keywords: silica fume, GGBS, compressive strength, permeability

Procedia PDF Downloads 358

Authors: Amel Ltifi, Ahmed Zouinkhi, Mohamed Salim Bouhlel

Abstract:

Security and trust management in Vehicular Ad-hoc NETworks (VANET) is a crucial research domain which is the scope of many researches and domains. Although, the majority of the proposed trust management systems for VANET are based on specific road infrastructure, which may not be present in all the roads. Therefore, road security should be managed by vehicles themselves. In this paper, we propose a new Self Organized Trust Management system (SOTM). This system has the responsibility to cut with the spread of false warnings in the network through four principal components: cooperation, trust management, communication and security.

Keywords: ative vehicle, cooperation, trust management, VANET

Procedia PDF Downloads 402

Authors: Abdul Qadir Jangda, Khadija Mariam, Usman Ahmed, Sharib Ahmed

Abstract:

The Gafchromic EBT3 film has the characteristic of high spatial resolution, weak energy dependence and near tissue equivalence which makes them viable to be used for in-vivo dosimetry in External Beam and Brachytherapy applications. The aim of this study is to assess the smallest film dimension that may be feasible for the use in in-vivo dosimetry. To evaluate the viability, the film sizes from 3 x 3 mm to 20 x 20 mm were calibrated with 6 MV Photon and 6 MeV electron beams. The Gafchromic EBT3 (Lot no. A05151201, Make: ISP) film was cut into five different sizes in order to establish the relationship between absorbed dose vs. film dimensions. The film dimension were 3 x 3, 5 x 5, 10 x 10, 15 x 15, and 20 x 20 mm. The films were irradiated on Varian Clinac® 2100C linear accelerator for dose range from 0 to 1000 cGy using PTW solid water phantom. The irradiation was performed as per clinical absolute dose rate calibratin setup, i.e. 100 cm SAD, 5.0 cm depth and field size of 10x10 cm2 and 100 cm SSD, 1.4 cm depth and 15x15 cm2 applicator for photon and electron respectively. The irradiated films were scanned with the landscape orientation and a post development time of 48 hours (minimum). Film scanning accomplished using Epson Expression 10000 XL Flatbed Scanner and quantitative analysis carried out with ImageJ freeware software. Results show that the dose variation with different film dimension ranging from 3 x 3 mm to 20 x 20 mm is very minimal with a maximum standard deviation of 0.0058 in Optical Density for a dose level of 3000 cGy and the the standard deviation increases with the increase in dose level. So the precaution must be taken while using the small dimension films for higher doses. Analysis shows that there is insignificant variation in the absorbed dose with a change in film dimension of EBT3 film. Study concludes that the film dimension upto 3 x 3 mm can safely be used up to a dose level of 3000 cGy without the need of recalibration for particular dimension in use for dosimetric application. However, for higher dose levels, one may need to calibrate the films for a particular dimension in use for higher accuracy. It was also noticed that the crystalline structure of the film got damage at the edges while cutting the film, which can contribute to the wrong dose if the region of interest includes the damage area of the film

Keywords: external beam radiotherapy, film calibration, film dosimetery, in-vivo dosimetery

Procedia PDF Downloads 474

Authors: Syed Ali Taqi, Muhammad Ismail

Abstract:

A comparative study of estimators of population means in two phase sampling in the presence of non-response when Unknown population means of the auxiliary variable(s) and incomplete information of study variable y as well as of auxiliary variable(s) is made. Three real data sets of University students, hospital and unemployment are used for comparison of all the available techniques in two phase sampling in the presence of non-response with the newly generalized ratio estimators.

Keywords: two-phase sampling, ratio estimator, product estimator, generalized estimators

Procedia PDF Downloads 216

Authors: Rukhsar Ahmed, Jawed Aziz Masudi

Abstract:

In the present study, an attempt has been made about the right to an education in Pakistan. The research is the focus in respect of International Law Article 26 of the Universal Declaration of Human Rights. The main motivation behind getting great training is, as a rule, decent resident and afterward being effective in close to home and expert life. We are fragmented without decent instruction since training makes us the right mastermind and right chief. In such a focused world, instruction has turned into a need for people after sustenance, dress and haven. It can give answers for all issues; it advances great propensities and mindfulness about defilement, fear-mongering, and other social issues among us.

Keywords: education, right to education, human right, universal declaration, law

Procedia PDF Downloads 132

Authors: Zellagui Redouane, Bellaouar Ahmed, Lachi Mohammed

Abstract:

The railway axles are the essential parts in the bogie of train, and its failure creates a big problem in the railway transport; during the work of this parts we noticed a premature deterioration. The aim has been presented a predictive model allowing the identification of the probable causes that are the cause of these premature deterioration. The results are employed for predicting fatigue crack growth in the railway axle, Also we want to present the variation value of stress intensity factor in different positions of elliptical crack tip. The modeling of axle in performed by the SOLID WORKS software and imported into ANSYS.

Keywords: crack growth, static load, railway axle, lifetime

Procedia PDF Downloads 336

Authors: Suyeb Ahmed Khan, Mahmood Mian

Abstract:

Simulation plays an important role during all phases of the design and engineering of communications systems, from early stages of conceptual design through the various stages of implementation, testing, and fielding of the system. In the present paper, a simulation model has been constructed for the WCDMA system in order to evaluate the performance. This model describes multiusers effects and calculation of BER (Bit Error Rate) in 3G mobile systems using Simulink MATLAB 7.1. Gaussian Approximation defines the multi-user effect on system performance. BER has been analyzed with comparison between transmitting data and receiving data.

Keywords: WCDMA, simulations, BER, MATLAB

Procedia PDF Downloads 567

Authors: Muhammad Heikal Ismail, Law Chung Lim, Hii Ching Lik

Abstract:

In maintaining food quality and shelf life, drying is employed in food industry as the most reliable perseverance technique. In this way, heat pump drying and hot air drying of fresh rice noodles was deduced to freeze drying in achieving quality attributes of oil content Scanning Electron Microscope (SEM) images, texture, and colour. Soxthlet analysis shows freeze dried noodles contain more than 10 times oil content, distinct pores of SEM images, higher hardness by more than three times, and wider colour changes by average more than two times to both methods to explain the less transparency physical outlook of freeze dried samples.

Keywords: freeze drying, heat pump drying, noodles, Soxthlet

Procedia PDF Downloads 464

Authors: Ahmed Madian, Muaz Aljarhi

Abstract:

Coordinate Rotation Digital Computer (CORDIC) is a unique digital computing unit intended for the computation of mathematical operations and functions. This paper presents a multi-CORDIC processor that integrates different CORDIC architectures on a single FPGA chip and allows the user to select the CORDIC architecture to proceed with based on what he wants to calculate and his/her needs. Synthesis show that radix 2 CORDIC has the lowest clock delay, radix 8 CORDIC has the highest LUT usage and lowest register usage while Hybrid Radix 4 CORDIC had the highest clock delay.

Keywords: multi, CORDIC, FPGA, processor

Procedia PDF Downloads 450

Authors: Nazeef, Suleiman, Umar, Danladi Muhammad, Ja'afar Ali, Zaliha Adamu Umar

Abstract:

The population dynamics of Auchenoglanis occidentalis from the Dadin-Kowa reservoir were studied. Population dynamic parameters such as growth, mortality and recruitment patterns were analyzed using length frequency data over a 12-month period employing FiSAT II software. Findings revealed that LWR (b - constant) = 2.88, K = 0.72 -yr., L∞ = 40.91 cm and Tmax = 3.57 years and Ɵ’ = 3.14. Mortality indices revealed that natural mortality (M = 1.39), fishing mortality (F = 0.22) and exploitation ratio (E = 0.14), Lc/L∞ = 0.48, Emax = 0.64, while Lopt = 26.4 cm. Uni-modal recruitment peak observed with Lm = 27.3 cm. A restocking program is suitable to ensure its continuous existence as it seems to have a low population.

Keywords: fish population dynamics, auchenoglanis occidentalis, FISAT II, natural mortality

Procedia PDF Downloads 18

Authors: Muhammad Umar Kiani, Waseem Sakawat

Abstract:

This study presents the development of FEM code using Quadrilateral 4-Node (Q4) and Triangular 3-Node (T3) elements. Code is formulated using MATLAB language. Instead of using both elements in the same code, two separate codes are written. Quadrilateral element is difficult to handle directly, that is why natural coordinates (eta, ksi) are used. Due to this, Q4 code includes numerical integration (Gauss quadrature). In this case, complete numerical integration is performed using 2 points. On the other hand, T3 element can be modeled directly, by using direct stiffness approach. Axially loaded element, cantilever (special constraints) and Patch test cases were analyzed using both codes and the results were verified by using Ansys.

Keywords: FEM code, MATLAB, numerical integration, ANSYS

Procedia PDF Downloads 397

Authors: Shafiq ur Rehman, Zubair Ahmed Shaikh

Abstract:

This research provides the comparative study of different mobile payment system and proposes an efficient solution of mobile payment system. The research involves discovering how the mobile payment methods can be used and implemented keeping user and system interaction under consideration. The implementation of Nielsen’s heuristic and universal design principles enhanced the user’s interaction design and made the system more appropriate, understandable and visible to the end user. The design of application is greatly affected by the user driven factors. These factors help in the efficiency of the application usage.

Keywords: mobile payment system, m-commerce, usability, near field communication

Procedia PDF Downloads 432

Authors: Shafique Qadir Memon, Muhammad Safar Mirjat, Abdul Quadir Mughal, Nadeem Amjad

Abstract:

The aims of this study were to determine direct input energy and indirect energy in maize production, to evaluate the inputs energy consumption and outputs energy gained for maize production in Islamabad, Pakistan for spring 2013. Results showed that grain yield was maximum under deep tillage as compared to conventional and zero tillage. Total energy input/output were maximum in deep tillage as compared to conventional tillage while lowest in zero tillage, net energy gain were found maximum under deep tillage.

Keywords: tillage, energy, grain yield, net energy gain

Procedia PDF Downloads 440

Authors: Somaya A. Abd El Mottaleb, Ahmed Abd El Aziz, Heba A. Fayed, Moustafa H. Aly

Abstract:

In this paper, we present the performance of spectral amplitude coding optical code division multiple access using different detectors at different transmission distances using single photodiode detection technique. Modified double weight codes are used as signature codes. Simulation results show that the system using avalanche photo detector can move distance longer than that using positive intrinsic negative photo detector.

Keywords: avalanche photodiode, modified double weight, multiple access technique, single photodiode.

Procedia PDF Downloads 585