Search results for: innovation program

Authors: V. E. Bazhenov, A. V. Li, A. A. Komissarov, A. V. Koltygin, S. A. Tavolzhanskii, O. O. Voropaeva, A. M. Mukhametshina, A. A. Tokar, V. A. Bautin

Abstract:

Magnesium-based alloys are considered as effective materials in the development of biodegradable implants. The magnesium alloys containing Mg, Zn, Ca as an alloying element are the subject of the particular interest. These elements are the nutrients for the human body, which provide their high biocompatibility. In this work, we investigated the effect of severe plastic deformation (SPD) on the mechanical and corrosion properties of Mg-Zn-Ca and Mg-Zn-Ca-Mn alloys containing from 2 to 4 wt.% Zn; 0.7 wt.% Ca and up to 1 wt.% Mn. Hot extrusion was used as a method of intensive plastic deformation. The temperature of hot extrusion was set to 220 °C and 300 °C. Metallographic analysis after hot extrusion shows that the grain size in the studied alloys depends on the deformation temperature. The grain size for all of investigated alloys is in the range from 3 to 7 microns, and 3 μm corresponds to the extrusion temperature of 220 °C. Analysis of mechanical properties after extrusion shows that extrusion at a temperature of 220 °C and alloying with Mn increase the strength characteristics and decrease the ductility of studied alloys. A slight anisotropy of properties in the longitudinal and transverse directions was also observed. Measurements of corrosion properties revealed that the addition of Mn to Mg-Zn-Ca alloys reduces the corrosion rate. On the other hand, increasing the Zn content in alloys increases the corrosion rate. The extrusion temperature practically does not affect the corrosion rate. Acknowledgement: The authors gratefully acknowledge the financial support of the Ministry of Science and Higher Education of the Russian Federation in the framework of Increase Competitiveness Program of NUST «MISiS» (No K2-2019-008), implemented by a governmental decree dated 16th of March 2013, N 211.

Keywords: biocompatibility, hot extrusion, magnesium alloys, severe plastic deformation, properties

Procedia PDF Downloads 93

Authors: P. Bhavya, P. R. Jayasree

Abstract:

This paper presents a low cost transformer isolated boost half bridge micro-inverter for single phase grid connected PV system. Since the output voltage of a single PV panel is as low as 20~50V, a high voltage gain inverter is required for the PV panel to connect to the single-phase grid. The micro-inverter has two stages, an isolated dc-dc converter stage and an inverter stage with a dc link. To achieve MPPT and to step up the PV voltage to the dc link voltage, a transformer isolated boost half bridge dc-dc converter is used. To output the synchronised sinusoidal current with unity power factor to the grid, a pulse width modulated full bridge inverter with LCL filter is used. Variable step size Maximum Power Point Tracking (MPPT) method is adopted such that fast tracking and high MPPT efficiency are both obtained. AC voltage as per grid requirement is obtained at the output of the inverter. High power factor (>0.99) is obtained at both heavy and light loads. This paper gives the results of computer simulation program of a grid connected solar PV system using MATLAB/Simulink and SIM Power System tool.

Keywords: boost-half-bridge, micro-inverter, maximum power point tracking, grid connection, MATLAB/Simulink

Procedia PDF Downloads 327

Authors: Siqi Fang, Jingxi Hou

Abstract:

Positive psychology and coaching psychology share a number of fundamental assumptions and common themes. Blending positive psychology, mindfulness, and coaching psychology, our work in team coaching with leaders enhances both leadership and team effectiveness. Although individual coaching has proven to be effective, this article advocates the benefits of leadership coaching in team settings, because durable changes in leadership behaviors are more likely to occur. Does leadership team coaching really work? Does it help improve senior leadership team effectiveness and productivity? This action research study answers these questions by tracking the progress of three typical senior leadership teams consisting of 31 executives participating in a six-month team coaching program. Assessments (pre- and post), workshops, and feedback based on ego development theories and mindfulness were applied to upgrade the senior leadership teams’ transformational stages and reframe their organizational leadership cultures. Results suggest that the team effectiveness of the three leadership teams increased up to 43 percent according to post-survey feedback from superior, direct report, and peers. Discussion is offered to show that senior leadership team coaching help teams to achieve a consensus on common purposes, establish a foundation of trust, improve collective skills, and promote efficient operation. All factors translate into better team performance. Implications of the results for future executive development programs are discussed and specific recommendations are provided.

Keywords: action research, ego development, mindfulness, senior leadership team coaching, team effectiveness, transformational stages

Procedia PDF Downloads 354

Authors: Adedayo Jeremiah Adeyekun, Samuel Oluwagbemiga Ishola,

Abstract:

This paper is an assessment of factors influencing the cost and time performance of subcontractors and the need for effective performance of subcontractors at the project sites. The factors influencing the performance of subcontractors are grouped, similar to those identified with the project or an organization and on another hand, there are significant factors influencing the performance of the subcontractors. These factors incorporate management level leadership, time required to complete the project, profit, staff capability/expertise, reputation, installment method, organization history, and project procurement method strategy, security, bidding technique, insurance, bond and relationship with the major contractors. The factors influencing the management of subcontractors in building development projects includes performance of significant past projects, standard of workmanship, consistence with guidelines, regular payment to labourers, adherence to program, regularity and viability of communication with main contractor, adherence to subcontract necessities. Other factors comprise adherence to statutory environmental regulations, number of experienced sites administrative staff, inspection and maintenance of good workplace, number of artisans and workers, quality of as-built and shop drawings and ability to carry out the quantity of work and so on. This study also aimed to suggest a way forward to improve the performance of subcontractors which is the reason for exceeding budget at the project sites. To carry out this study, a questionnaire was drafted to derive information on the causes of low performance of subcontractors and the implication to cost.

Keywords: performance, contractor, subcontractors, construction

Procedia PDF Downloads 61

Authors: Michael Sinclair, Andrea Ghermandi, Sheela A. Moses, Joseph Sabu

Abstract:

Passively crowdsourced data, such as geotagged photographs from social media, represent an opportunistic source of location-based and time-specific behavioral data for ecosystem services analysis. Such data have innovative applications for environmental management and protection, which are replicable at wide spatial scales and in the context of both developed and developing countries. Here we test one such innovation, based on the analysis of the metadata of online geotagged photographs, to investigate the provision of recreational services by the entire network of wetland ecosystems in the state of Kerala, India. We estimate visitation to individual wetlands state-wide and extend, for the first time to a developing region, the emerging application of cultural ecosystem services modelling using data from social media. The impacts of restoration of wetland areal extension and water quality improvement are explored as a means to inform more sustainable management strategies. Findings show that improving water quality to a level suitable for the preservation of wildlife and fisheries could increase annual visits by 350,000, an increase of 13% in wetland visits state-wide, while restoring previously encroached wetland area could result in a 7% increase in annual visits, corresponding to 49,000 visitors, in the Ashtamudi and Vembanad lakes alone, two large coastal Ramsar wetlands in Kerala. We discuss how passive crowdsourcing of social media data has the potential to improve current ecosystem service analyses and environmental management practices also in the context of developing countries.

Keywords: coastal wetlands, cultural ecosystem services, India, passive crowdsourcing, social media, wetland restoration

Procedia PDF Downloads 136

Authors: Hamad Albadr

Abstract:

Joint Commission International (JCI) accreditation process intent to improve the safety and quality of care in the international community through the provision of education, publications, consultation, and evaluation services. These standards apply to the entire organization as well as to each department, unit, or service within the organization. Medical Technology that contains both medical equipment and devices, is an essential part of health care. Appropriate management of equipment maintenance for ensuring medical technology safe, the equipment life is maximized, and the total costs are minimized. JCI medical technology evaluation and accreditation use standards, intents, and measurable elements. The paper focuses on evaluation of JCI standards for medical technology in Saudi Arabian hospitals: a Study Case of PSMMC that define the performance expectation, structures, or functions that must be in place for a hospital to be accredited by JCI through measurable elements that indicate a score during the survey process that identify the requirements for full compliance with the standard specially through Facility Management and Safety (FMS) section that require the hospital establishes and implements a program for inspecting, testing, and maintaining medical technology and documenting the results, to ensure that medical technology is available for use and functioning properly, the hospital performs and documents; an inventory of medical technology; regular inspections of medical technology; testing of medical technology according to its use and manufacturers’ requirements; and performance of preventive maintenance.

Keywords: joint commission international (JCI) accreditation, medical technology, Saudi Arabia, Saudi Arabian hospitals

Procedia PDF Downloads 539

Authors: Matthew Armitt

Abstract:

The revolutionary school of architectural teaching – VKhUTEAMAS (1923-1926) was a new approach for a new society bringing architectural education to the masses and masses to the growing industrial production. The school's pedagogical contribution of the 1920s made it an important school of the modernist movement, engaging pedagogy as a mode of experimentation. The teachers and students saw design education not just as a process of knowledge transfer but as a vehicle for design innovation developing an approach without precedent. This process of teaching and learning served as a vehicle for venturing into the unknown through a discipline of architectural teaching called “Space” developed by the Soviet architect Nikolai Ladovskii (1881-1941). The creation of “Space” was paramount not only for its innovative pedagogy but also as an experimental laboratory for developing new architectural language. This paper discusses whether the historical teaching of “Space” can function in the construction of the modern teaching identity today to promote value, richness, quality, and diversity inherent in architectural design education. The history of “Space” teaching remains unknown within academic circles and separate from the current architectural teaching debate. Using VKhUTEMAS and the teaching of “Space” as a pedagogical lens and drawing upon research carried out in the Russian Federation, America, Canada, Germany, and the UK, this paper discusses how historically different models of teaching and learning can intersect through examining historical based educational research by exploring different design studio initiatives; pedagogical methodologies; teaching and learning theories and problem-based projects. There are strong arguments and desire for pedagogical change and this paper will promote new historical and educational research to widen the current academic debate by exposing new approaches to architectural teaching today.

Keywords: VKhUTEMAS, discipline space, modernist pedagogy, teaching identity

Procedia PDF Downloads 113

Authors: John Bankier

Abstract:

Development of academic English occurs not only in communities of practice but also within wider social networks, referred to by Zappa-Hollman and Duff as individual networks of practice. Such networks may exist whether students are developing academic English in English-dominant contexts or in contexts in which English is not a majority language. As yet, little research has examined how newcomers to universities interact with a variety of social ties in such networks to receive academic and emotional support as they develop the academic English necessary to succeed in local and global academia. The one-year ethnographic study described in this presentation followed five Japanese university students enrolled on an academic English program in their home country. We graphically represent participants’ individual networks of practice related to academic English and display the role of interaction in these networks to socialization. Specific examples of academic practices will be linked to specific instances of social interaction. Interaction supportive of the development of academic practices often occurred during unplanned interactions outside the classroom and among small groups of close friends who were connected to each other in more than one way, such as those taking multiple classes together. These interactions occurred in study spaces, in hallways between class periods, at lunchtimes, and online. However, constraints such as differing accommodation arrangements, class scheduling and the hierarchical levelling of English classes by test scores discouraged some participants both from forming strong ties related to English and from interacting with existing ties. The presentation will briefly describe ways in which teachers in all contexts can maximise interaction outside the classroom.

Keywords: academic, english, practice, network

Procedia PDF Downloads 245

Authors: Hamid Mustafa, Huson J. Heather, Kim Eiusoo, McClure Matt, Khalid Javed, Talat Nasser Pasha, Afzal Ali1, Adeela Ajmal, Tad Sonstegard

Abstract:

Genetic differences associated with speciation, breed formation or local adaptation can help to preserve and effective utilization of animals in selection programs. Analyses of population structure and breed diversity have provided insight into the origin and evolution of cattle. In this study, we used a high-density panel of SNP markers to examine population structure and diversity among ten Pakistani indigenous cattle breeds. In total, 25 individuals from three cattle populations, including Achi (n=08), Bhagnari (n=04) and Cholistani (n=13) were genotyped for 777, 962 single nucleotide polymorphism (SNP) markers. Population structure was examined using the linkage model in the program STRUCTURE. After characterizing SNP polymorphism in the different populations, we performed a detailed analysis of genetic structure at both the individual and population levels. The whole-genome SNP panel identified several levels of population substructure in the set of examined cattle breeds. We further searched for spatial patterns of genetic diversity among these breeds under the recently developed spatial principal component analysis framework. Overall, such high throughput genotyping data confirmed a clear partitioning of the cattle genetic diversity into distinct breeds. The resulting complex historical origins associated with both natural and artificial selection have led to the differentiation of numerous different cattle breeds displaying a broad phenotypic variety over a short period of time.

Keywords: Pakistan, cattle, genetic diversity, population structure

Procedia PDF Downloads 599

Authors: Hana A. Jameel Alsaeed, Rayyan Ibrahim Khaleel, Hanaa Hussein Mukhlif

Abstract:

Background: Contamination in Iraq's hospitals is a localized problem with high rates of disease And deaths that mainly affect poor areas. Thus, this study aims to evaluate hospital infections in the city of Mosul and to identify the etiology. So to assess environmental infection prevention in pediatric wards and newborn critical care units in Mosul city. Methods: The present study is a cross-sectional hospital based in Mosul-Iraq between (10th February to 1st April 2022). Purposive sample of 60 nurses from neonatal intensive care units and pediatric wards in three pediatric teaching hospitals in Mosul city; Data was gathered using a questionnaire created by the researchers after reviewing previous studies. Results: The study showed that the majority of the study infection prevention and control policy isn't available in 46.7% of departments, and 45% of hospital workers in Iraq don't know if there is an Iraqi version of it. 70% of the study group had participated in an infection control training program. Conclusions: In the majority of samples 55% of respondents to the study claimed not to be aware of these rules. 60% of the study's participants had never attended a course on infection prevention and control, according to the study's findings on education and training programs. In the neonatal and critical care unit, nurses' skill levels, years of experience, and actual duties varied by wide statistically significant differences.

Keywords: pediatric, infection control, assessment, mosul city

Procedia PDF Downloads 67

Authors: Haifa Saleh, Kamiran Abduka, Robin Kalfat, Riadh Al-Mahaidi

Abstract:

The effectiveness of using pre-stressing steel bars for shear strengthening of high strength reinforced concrete (RC) slabs was assessed. Two large-scale RC slabs were tested, one without shear reinforcement and the second strengthened against punching shear failure using pre-stressing steel bars. The two slabs had the same dimensions, flexural reinforcement ratio, loading and support arrangements. The experimental program including the method of strengthening, set up and instrumentation are described in this paper. The experimental results are analyzed and discussed in terms of the structural behavior of the RC slabs, the performance of pre-stressing steel bolts and failure modes. The results confirmed that the shear strengthening technique increased the shear capacity, ductility and yield capacity of the slab by up to 15%, 44%, and 22%, respectively compared to the unstrengthened slab. The strengthening technique also successfully contributed to changing the failure mode from a brittle punching shear mode to ductile flexural failure mode. Vic3D digital image correlation system (photogrammetry) was also used in this research. This technique holds several advantages over traditional contact instrumentations including that it is inexpensive, it produces results that are simple to analyze and it is remote visualization technique. The displacement profile along the span of the slab and rotation has been found and compared with the results obtained from traditional sensors. The performance of the photogrammetry technique was very good and the results of both measurements were in very close agreement.

Keywords: flat slab, photogrammetry, punching shear, strengthening

Procedia PDF Downloads 147

Authors: Susan K. Steele-Moses, Aimee Badeaux

Abstract:

Background Literature: Nurse anesthesia education placed high demands on students both personally and professionally. High levels of anxiety affect student’s mental, emotional, and physical well-being, which impacts their student success. Whereas more research has focused on the health and well-being of graduate students, far less has focused specifically on nurse anesthesia students (SNRAs), who may experience higher levels of anxiety due to the rigor of their academic program. Current literature describes stressors experienced by SRNAs that cause anxiety and affect their performance, including personal, academic, clinical, interpersonal, emotional, and financial. Sample: DNP-NA 2025 and DNP-NA 2024 cohorts (N = 36). Eighteen (66.7%) students participated in the study. Instrumentation: The DASS-21 was used to measure stress (7 items; α = .87) and anxiety (7 items; α = .74) from the participants. Intervention: The mind-shift meditation app, based on cognitive behavioral therapy, is being used daily before clinical and exams to decrease nurse anesthesia students’ stress and anxiety over time. Results: At baseline, the students exhibited a moderate level of stress, but their anxiety levels were low. The range of scores was 4-21 (out of 28) for stress (M = 12.88; SD = 5.40) and 0-16 (out of 28) for anxiety (M = 6.81; SD = 5.04). Both stress and anxiety were normally distributed [SW = .242 (stress); SW = .210 (anxiety)] without any outliers. There was a significant difference between their stress and anxiety levels (t = 5.55; p < .001) at baseline. Stress and anxiety will be measured over time, with the change analyzed using repeated measures ANOVA. Implications for Practice: The use of purposeful mindfulness meditation has been shown to decrease stress and anxiety in nursing students.

Keywords: mindfulness, meditation, graduate nursing education, nursing education

Procedia PDF Downloads 63

Authors: Indhumathi Gopal

Abstract:

Undergraduate research is well documented in Science, Technology, Engineering, and Mathematics (STEM), neurosciences, and microbiology disciplines, though it is hardly part of a physical fitness & wellness discipline. However, students need experiential learning opportunities, like internships and research assistantships, to get ahead with graduate schools and be gainfully employed. The first step towards this goal is to have students do a simple research project in a semester-long course. The value of research experiences and how to integrate research activity in a physical fitness & wellness course are discussed. The investigator looks into a mini research project, “Awareness of Obesity among College Students” and explains how to guide students through the research process, including journal search, data collection, and basic statistics. Besides, students will be introduced to the statistical package program SPSS 22.0 to assist with data evaluation. The lab component of the combined lecture-physical activity course could include the measurement of student’s weight with respect to their height to obtain body mass index (BMI). Students could categorize themselves in accordance with the World Health Organization’s guidelines. Results obtained after completing the data analysis help students be aware of their own potential health risks associated with overweight and obesity. Overweight and obesity are risk factors for hypertension, hypercholesterolemia, heart disease, stroke, diabetes, and certain types of cancer. It is hoped that this experience will get students interested in scientific studies, gain confidence, think critically, and develop problem-solving and good communication skills.

Keywords: physical fitness, undergraduate research experience, obesity, BMI

Procedia PDF Downloads 56

Authors: B. Engel, H. Hassan

Abstract:

Rotary draw bending is a method which is being used in tube forming. In the tube bending process, the neutral axis moves towards the inner arc and the wall thickness distribution changes for tube’s cross section. Thinning takes place in the outer arc of the tube (extrados) due to the stretching of the material, whereas thickening occurs in the inner arc of the tube (intrados) due to the comparison of the material. The calculations of the wall thickness distribution, neutral axis shifting, and strain distribution have not been accurate enough, so far. The previous model (the geometrical model) describes the neutral axis shifting and wall thickness distribution. The geometrical of the tube, bending radius and bending angle are considered in the geometrical model, while the influence of the material properties of the tube forming are ignored. The advanced model is a modification of the previous model using material properties that depends on the correction factor. The correction factor is a purely empirically determined factor. The advanced model was compared with the Finite element simulation (FE simulation) using a different bending factor (Bf=bending radius/ diameter of the tube), wall thickness (Wf=diameter of the tube/ wall thickness), and material properties (strain hardening exponent). Finite element model of rotary draw bending has been performed in PAM-TUBE program (version: 2012). Results from the advanced model resemble the FE simulation and the experimental test.

Keywords: rotary draw bending, material properties, neutral axis shifting, wall thickness distribution

Procedia PDF Downloads 383

Authors: Fauzik Lendriyono, Isbandi Rukminto Adi

Abstract:

Muhammadiyah is an Islamic-based organization taking care to human suffering. The existence of Muhammadiyah organization is strong supported by its members. Muhammadiyah as the oldest Islamic organization in Indonesia, since its establishment has had main activities, such as in the fields of education, health, and social services, one of the form is Orphanage. However, at present, Muhammadiyah orphanage was in a dilemma because of differences in orientation and commitment of the caretaker-managers. This research on Muhammadiyah orphanage is very important because it is able to know the problem identification and to find the ideal concept for the better management of an orphanage in Muhammadiyah. This research is a phenomenology study by research subjects: caretaker of the orphanage in Muhammadiyah at Great Malang. The research data was obtained after the observation, in-depth interviews, review of documentation and the discussion focused. Data were analyzed with interpretative phenomenological analysis. Basic problems for causes of differences in orientation and commitment administrators of Muhammadiyah orphanage is the influence of organizational culture and organizational environment factors. Organizational culture factors include the Islamic-based value and organization ideology, so that the Islamic values and the values of Muhammadiyah are used as guidelines in the orphanage. Environmental factors include the demand for its organization sustainability as characterized by economically productive activities organized by Orphanage and a program to produce a cadre of Muhammadiyah. To support the social welfare of Muhammadiyah, the ideal Orphanage concept for Muhammadiyah is a missionary and self-sufficient orphanage.

Keywords: orphanage, Muhammadiyah, misionary, Great Malang

Procedia PDF Downloads 186

Authors: S. Lemoussu, J. C. Chaudemar, R. A. Vingerhoeds

Abstract:

The aeronautics sector is currently living an unprecedented growth largely due to innovative projects. In several cases, such innovative developments are being carried out by Small and Medium sized-Enterprises (SMEs). For instance, in Europe, a handful of SMEs are leading projects like airships, large civil drones, or flying cars. These SMEs have all limited resources, must make strategic decisions, take considerable financial risks and in the same time must take into account the constraints of safety, cost, time and performance as any commercial organization in this industry. Moreover, today, no international regulations fully exist for the development and certification of this kind of projects. The absence of such a precise and sufficiently detailed regulatory framework requires a very close contact with regulatory instances. But, SMEs do not always have sufficient resources and internal knowledge to handle this complexity and to discuss these issues. This poses additional challenges for those SMEs that have system integration responsibilities and that must provide all the necessary means of compliance to demonstrate their ability to design, produce, and operate airships with the expected level of safety and reliability. The final objective of our research is thus to provide a methodological framework supporting SMEs in their development taking into account recent innovation and institutional rules of the sector. We aim to provide a contribution to the problematic by developing a specific Model-Based Systems Engineering (MBSE) approach. Airspace regulation, aeronautics standards and international norms on systems engineering are taken on board to be formalized in a set of models. This paper presents the on-going research project combining Systems Engineering and Project Management process modeling and taking into account the metamodeling problematic.

Keywords: aeronautics, certification, process modeling, project management, SME, systems engineering

Procedia PDF Downloads 152

Authors: Gbenga Martins, Christopher J. Olowookere, Lateef Bamidele, Kehinde O. Olatunji

Abstract:

The aims of this research are to measure the scattered dose rate during an X-ray examination in an X-ray room, compare the scattered dose rate with exposure parameters based on the body region examined, and examine the X-ray examination done with an over couch tube. The research was carried out using Gamma Scout software installation on the computer system (Laptop) to record the radiation counts, pulse rate, and dose rate. The measurement was employed by placing the detector at 900 to the incident X-ray. Proforma was used for the collection of patients’ data such as age, sex, examination type, and initial diagnosis. Data such as focus skin distance (FSD), body mass index (BMI), body thickness of the patients, the beam output (kVp) were collected at Obafemi Awolowo University, Ile-Ife, Western Nigeria. Total number of 136 patients was considered during this research. Dose rate range between 14.21 and 86.78 µSv/h for the plain abdominal region, 85.70 and 2.86 µSv/h for the lumbosacral region,1.3 µSv/yr and 3.6 µSv/yr in the pelvis region, 2.71 µSv/yr and 28.88 µSv/yr for leg region, 3.06 µSv/yr and 29.98 µSv/yr in hand region. The results of this study were compared with those of other studies carried out in other countries. The findings of this study indicated that the number of exposure parameters selected for each diagnostic examination contributed to the dose rate recorded. Therefore, these results call for a quality assurance program (QAP) in diagnostic X-ray units in Nigerian hospitals.

Keywords: X-radiation, exposure parameters, dose rate, pulse rate, number of counts, tube current, tube potential, diagnostic examination, scattered radiation

Procedia PDF Downloads 95

Authors: Chanda Burrage

Abstract:

The past half-century has revealed massive structural, geographic, and technological changes in livestock production. The move, for instance, toward expanding export markets, massive feedlots for the fattening of cattle and improved veterinary standards is a global trend in food animal agribusiness and is apparent in both developed and developing regions. In the Horn of Africa, various breeds of cattle that previously were not considered in economic terms are now treated as commodities and branded for numerous export markets. Formerly a culturally significant exchange good within the subsistence pastoral livelihoods, cattle are now identified as a key economic resource and fully connected to global markets. This study incorporates an ethnographic-commodity chain approach to examine critical issues surrounding regional trade, harmonization of standards, import & export legislation, the role of the private sector, and infrastructure development relative to the Boran cattle breed and Borana pastoralists. The specific sites assessed include the cattle production region of Moyale in southern Ethiopia, feedlots and export abattoirs in Adama, Ethiopia, and quarantines and ports in Djibouti and Somaliland. The goal is to evaluate innovation and modernization outcomes and narratives around Boran cattle production and development and the associate livelihood changes for cattle producers in southern Ethiopia and how the smallholder pastoralists are coping with the multitude of global changes. Inevitably, the inherent pressures related to such changes alter, and may even promote the reconfiguration of identity, while inadvertently contribute to the capacity of smallholder cattle producers to act independently and make their own free choices in sustainability. It is through these processes that local Borana groups may appropriate, bypass, or put to new use available and innovative material resources.

Keywords: globalization, global change, commodification, pastoralism, vulnerability, adaptive capacity

Procedia PDF Downloads 376

Authors: Zaw Z Aung

Abstract:

Background: High-risk groups for hepatitis B infection (HBV) are people who injected drugs (PWID), men who have sex with men (MSM), people living with HIV (PLHIV) and persons with hepatitis C (HCV), etc. HBV/HCV coinfected patients are at increased risk of cirrhosis, hepatic decompensation and hepatocellular carcinoma. To the best of author’s knowledge, there is currently no data for hepatitis B vaccine utilization in HCV positive patients and their antibody response. Methodology: From February 2018 to May 2018, consented participants at or above 18 years who came to the clinic in Mandalay were tested with the anti-HCV rapid test. Those who tested HCV positive (n=168) were further tested with hepatitis B profile and asked about their previous hepatitis B vaccination history and risk factors. Results: Out of 168 HCV positive participants, three were excluded for active HBV infections. The remaining 165 were categorized into previously vaccinated 64% (n=106) and unvaccinated 36% (n=59) There were three characteristics groups- PWID monoinfected (n=77), General Population (GP) monoinfected (n=22) and HIV/HCV coinfected participants (n=66). Unvaccinated participants were highest in HIV/HCV, with 68%(n=45) followed by GP (23%, n=5) and PWID (12%, n=9). Among previously vaccinated participants, the highest percentage was PWID (88%, n=68), the second highest was GP (77%, n=17) and lowest in HIV/HCV patients (32%, n=21). 63 participants completed third doses of vaccination (PWID=36, GP=13, HIV/HCV=14). 53% of participants who completed 3 dose of hepatitis B were non-responders (n=34): HIV/HCV (86%, n=12), PWID (44%, n=16), and GP (46%, n=6) Conclusion: Even in the presence of effective and safe hepatitis B vaccine, uptake is low among high risk groups especially PLHIV that needs to be improved. Integration or collaboration of hepatitis B vaccination program, HIV/AIDS and hepatitis C treatment centers is desirable. About half of vaccinated participants were non-responders so that optimal doses, schedule and follow-up testing need to be addressed carefully for those groups.

Keywords: Hepatitis B vaccine, Hepatitis C, HIV, Myanmar

Procedia PDF Downloads 126

Authors: Ahmed Mousa, Huda Mazeed

Abstract:

The research aims to determine the appropriate songs and artistic indications for the kindergarten child. In addition, it aims to use the songs of folk to develop expressive visual drawings with artistic connotations for the kindergarten child. The current research used a one group semi-experimental approach to identify the impact of songs on expressive children's drawings. The research community is represented in the educational administration in Giza Governorate for the academic year (2018 - 2019). The sample was taken from the kindergarten of Gamal Abdel Nasser School of Dokki Educational Administration in Giza Governorate. The study was applied to the second level children sample (5-6 years), where they numbered 20 children, males and females. The research results show that there are statistically significant differences between the average scores of the children of the experimental group in the pre and post-measurements on the observation card for children after hearing the songs of social and national folk in favor of post measurement. Moreover, the results demonstrate that there are no statistically significant differences between the average scores of children in the experimental group in the measurements, the post and follow-up, on the observation card of children's drawings for social and national folk.

Keywords: folk songs, visual expressive, artistic connotations, early childhood

Procedia PDF Downloads 158

Authors: Elizabeth Starzycka-Korbas, Michal Starzycki, Wojciech Rybinski, Mirosława Dabert

Abstract:

For a few years, the populations of pathogenic fungi occurring in winter oilseed rape in Malyszyn were analyzed. Brassica napus L. in Poland and in the world is a source of energy for both the men (oil), and animals, as post-extraction middling, as well as a motor fuel (oil, biofuel) therefore studies of this type are very important. The species composition of pathogenic fungi can be an indicator of seed yield. The occurrence of oilseed rape pathogens during several years were analyzed using the sequencing method DNA ITS. The results were compared in the gene bank using the program NCBI / BLAST. In field conditions before harvest of oilseed rape presence of pathogens infesting B. napus has been assessed. For example, in 2015, 150 samples have been isolated and applied to PDA medium for the identification of belonging species. From all population has been selected mycelium of 83 isolates which were sequenced. Others (67 isolates) were pathogenic fungi of the genus Alternaria which are easily to recognize. The population of pathogenic species on oilseed rape have been identified after analyzing the DNA ITS and include: Leptosphaeria sp. 38 (L. maculans 25, L. biglobosa 13), Alternaria sp. 29, Fusarium sp. 3, Sclerotinia sclerotiorum 7, heterogeneous 6, total of 83 isolates. The genus Alternaria sp. fungi wear the largest share of B. napus pathogens in particular years. Another dangerous species for oilseed rape was Leptosphaeria sp. Populations of pathogens in each year were different. The number of pathogens occurring in the field and their composition is very important for breeders and farmers because of the possible selection of the most resistant genotypes for sowing in the next growing season.

Keywords: B. napus, DNA ITS Sequencing, pathogenic fungi, population

Procedia PDF Downloads 275

Authors: Azizah Ismail, Zainab Khalifah, Abbas Mardani

Abstract:

Sustainable community-based tourism through homestay programme is a growing niche market that has impacted destinations in many countries including Malaysia. With demand predicted to continue increasing, the importance of the homestay product will grow in the tourism industry. This research examines the sustainability criteria for homestay programme in Malaysia covering economic, socio-cultural and environmental dimensions. This research applied a two-stage methodology for data analysis. Specifically, the researcher implements a hybrid method which combines two multi-criteria decision making approaches. In the first stage of the methodology, the Decision Making Trial and Evaluation Laboratory (DEMATEL) technique is applied. Then, Analytical Network Process (ANP) is employed for the achievement of the objective of the current research. After factors identification and problem formulation, DEMATEL is used to detect complex relationships and to build a Network Relation Map (NRM). Then ANP is used to prioritize and find the weights of the criteria and sub-criteria of the decision model. The research verifies the framework of multi-criteria for sustainable community-based tourism from the perspective of stakeholders. The result also provides a different perspective on the importance of sustainable criteria from the view of multi-stakeholders. Practically, this research gives the framework model and helps stakeholders to improve and innovate the homestay programme and also promote community-based tourism.

Keywords: community-based tourism, homestay programme, sustainable tourism criteria, sustainable tourism development

Procedia PDF Downloads 116

Authors: Jorge Anibal Restrepo Morales, Sonia Martín Gómez

Abstract:

A model based on a logical framework was developed to quantify SMEs' internationalization capacity. To do so, linguistic variables, such as human talent, infrastructure, innovation strategies, FTAs, marketing strategies, finance, etc. were integrated. It is argued that a company’s management of international markets depends on internal factors, especially capabilities and resources available. This study considers internal factors as the biggest business challenge because they force companies to develop an adequate set of capabilities. At this stage, importance and strategic relevance have to be defined in order to build competitive advantages. A fuzzy inference system is proposed to model the resources, skills, and capabilities that determine the success of internationalization. Data: 157 linguistic variables were used. These variables were defined by international trade entrepreneurs, experts, consultants, and researchers. Using expert judgment, the variables were condensed into18 factors that explain SMEs’ export capacity. The proposed model is applied by means of a case study of the textile and clothing cluster in Medellin, Colombia. In the model implementation, a general index of 28.2 was obtained for internationalization capabilities. The result confirms that the sector’s current capabilities and resources are not sufficient for a successful integration into the international market. The model specifies the factors and variables, which need to be worked on in order to improve export capability. In the case of textile companies, the lack of a continuous recording of information stands out. Likewise, there are very few studies directed towards developing long-term plans, and., there is little consistency in exports criteria. This method emerges as an innovative management tool linked to internal organizational spheres and their different abilities.

Keywords: business strategy, exports, internationalization, fuzzy set methods

Procedia PDF Downloads 284

Authors: Khaled Saad Eldin Mohamed Ragab

Abstract:

This paper investigates analytically the torsion behavior of steel fibered high strength self compacting concrete beams reinforced by GFRP bars. Nonlinear finite element analysis on 12­ beams specimens was achieved by using ANSYS software. The nonlinear finite element analysis program ANSYS is utilized owing to its capabilities to predict either the response of reinforced concrete beams in the post elastic range or the ultimate strength of a reinforced concrete beams produced from steel fiber reinforced self compacting concrete (SFRSCC) and reinforced by GFRP bars. A general description of the finite element method, theoretical modeling of concrete and reinforcement are presented. In order to verify the analytical model used in this research using test results of the experimental data, the finite element analysis were performed. Then, a parametric study of the effect ratio of volume fraction of steel fibers in ordinary strength concrete, the effect ratio of volume fraction of steel fibers in high strength concrete, and the type of reinforcement of stirrups were investigated. A comparison between the experimental results and those predicted by the existing models are presented. Results and conclusions thyat may be useful for designers have been raised and represented.

Keywords: nonlinear analysis, torsionally loaded, self compacting concrete, steel fiber reinforced self compacting concrete (SFRSCC), GFRP bars and sheets

Procedia PDF Downloads 445

Authors: S. Fahiminiya, J. Nadaf, F. Rauch, L. Jerome-Majewska, J. Majewski

Abstract:

Background: Sequencing of protein coding regions of human genome (Whole Exome Sequencing; WES), has demonstrated a great success in the identification of causal mutations for several rare genetic disorders in human. Generally, most of WES studies have focused on rare variants in coding exons and splicing-sites where missense substitutions lead to the alternation of protein product. Although focusing on this category of variants has revealed the mystery behind many inherited genetic diseases in recent years, a subset of them remained still inconclusive. Here, we present the result of our WES studies where analyzing only rare variants in coding regions was not conclusive but further investigation revealed the involvement of non-coding variants and copy number variations (CNV) in etiology of the diseases. Methods: Whole exome sequencing was performed using our standard protocols at Genome Quebec Innovation Center, Montreal, Canada. All bioinformatics analyses were done using in-house WES pipeline. Results: To date, we successfully identified several disease causing mutations within gene coding regions (e.g. SCARF2: Van den Ende-Gupta syndrome and SNAP29: 22q11.2 deletion syndrome) by using WES. In addition, we showed that variants in non-coding regions and CNV have also important value and should not be ignored and/or filtered out along the way of bioinformatics analysis on WES data. For instance, in patients with osteogenesis imperfecta type V and in patients with glucocorticoid deficiency, we identified variants in 5'UTR, resulting in the production of longer or truncating non-functional proteins. Furthermore, CNVs were identified as the main cause of the diseases in patients with metaphyseal dysplasia with maxillary hypoplasia and brachydactyly and in patients with osteogenesis imperfecta type VII. Conclusions: Our study highlights the importance of considering non-coding variants and CNVs during interpretation of WES data, as they can be the only cause of disease under investigation.

Keywords: whole exome sequencing data, non-coding variants, copy number variations, rare diseases

Procedia PDF Downloads 402

Authors: Andrea Palazzo, Daniel Macek, Veronika Malinova

Abstract:

Contour processing is the new technology challenge for architects and construction companies. The many advantages it promises make it one of the most interesting solutions for construction in terms of automation of building processes. The technology for 3D printing houses offers many application possibilities, from low-cost construction, to being considered by NASA for visionary projects as a good solution for building settlements on other planets. Another very important point is that clients, as architects, will no longer have many limits in design concerning ideas and creativity. The prices for real estate are constantly increasing and the lack of availability of construction materials as well as the speculation that has been created around it in 2021 is bringing prices to such a level that in the future real estate developers risk not being able to find customers for these ultra-expensive homes. Hence, this paper starts with the introduction of 3D printing, which now has the potential to gain an important position in the market, becoming a valid alternative to the classic construction process. This technology is not only beneficial from an economic point of view but it is also a great opportunity to have an impact on the environment by reducing CO2 emissions. Further on in the article we will also understand if, after the COP 26 (2021 United Nations Climate Change Conference), world governments could also push towards building technologies that reduce the waste materials that are needed to be disposed of and at the same time reduce emissions with the contribution of governmental funds. This paper will give us insight on the multiple benefits of 3D printing and emphasise the importance of finding new solutions for materials that can be used by the printer. Therefore, based on the type of material, it will be possible to understand the compatibility with current regulations and how the authorities will be inclined to support this technology. This will help to enable the rise and development of this technology in Europe and in the rest of the world on actual housing projects and not only on prototypes.

Keywords: additive manufacturing, contour crafting, development, new regulation, printing material

Procedia PDF Downloads 181

Authors: Gargi Ghosh

Abstract:

Municipal solid waste management (MSWM) is an obligatory function of the local self-government as per the Indian constitution, and this paper gives a glimpse of the system in Indian towns focusing on its present state and use of technology in the system. The paper analyses the MSWM characteristics in 35 towns in the southern state of Karnataka. The lifestyle in these towns was found to be very sustainable with minimal disposal and considerable reuse. Average per capita waste generated in the towns ranged from 300 gm/person to 500 gm/person. The waste collection efficiency varied from 60% to 80%. The waste shows equal share of organic and non-organic waste composition with a low calorific value. Lack of capacity of the municipal body in terms of manpower, assets & knowledge and social consciousness were found to be two major issues in the system. Technical solutions in use in India at present are composting, organic re-reprocessing, bio-methanation, waste to energy etc. The tonnage of waste generated ranged from 8 TPD to 80 TPD. The feasibility of technology has been analysed in the context of the above characteristics. It was found that low calorific value and mixed nature of waste made waste to energy and bio methanation processes unsuitable. Composting – windrow and closed door was found best to treat the bulk of the waste. Organic–re-processors was planned for phase 2 of MSWM program in the towns with effective implementation of segregation at source. GPS and RFID technology was recommended for monitoring the collection process and increasing accountability of the citizens for effective implementation.

Keywords: solid waste management, Indian towns, waste management technology, waste charateristics

Procedia PDF Downloads 305

Authors: Marzena Trojanczyk, Mariusz Jaworski, Ewa Dmoch Gajzlerska

Abstract:

Purpose: The purpose of this paper is to assess the relationship between the level of quality of life and willingness to take treatment in patients with eating disorders as anorexia, bulimia and compulsive bingeing. Material and methods: The subjects consisted of 99 women with eating disorders: anorexia, n = 33; bulimia, n = 35; compulsive overeating, n = 31 and 35 women in the control group. The study used an original questionnaire to assess the overall quality of life, as well as selected areas of the physical, mental, social and spiritual satisfaction. The subjects were also asked about the level of motivation for treatment, and the importance of the disease in the lives of patients. Statistical analyses were performed using the statistical program SPSS 18.0. Results: Women with eating disorders in particular groups did not differ with respect to each other in the aspect of overall quality of life, satisfaction with the development of the spiritual, social functioning and mental health. The severity level of the disease in the lives of patients showed a negative correlation with social functioning in women with anorexia nervosa. In the case of patients with compulsive bingeing a positive relationship between the level of importance of the disease and the satisfaction of spiritual development is reported. Conclusions: Concerning the inferior quality of life, there is no relationship between a willingness to take treatment and the importance of the disease in the lives of patients with anorexia, bulimia and compulsive bingeing.

Keywords: anorexia, bulimia, compulsive overeating, quality of life

Procedia PDF Downloads 374

Authors: W. Kongnoo, J. Loysongkroa, S. Chotivichien, N. Viriyautsahakul, N. Saiwongse

Abstract:

Obesity, stunting and wasting problems among Thai school-aged children are increasing due to inappropriate food consumption behavior and poor environments for desirable nutritional behavior. Because of a low school lunch budget of only 0.40 USD per person per day, food quality is not up to nutritional standards. Therefore, the Health Department with the Education Ministry and the Thai Health Promotion Foundation have developed a quality school lunch project during 2009–2013. The program objectives were development and management of public policy to increase school lunch budget. The methods used a healthy public policy motivation process and movement in 241 local administrative organizations and 538 schools. The problem and solution research was organized to study school food and nutrition management, create a best practice policy mobilization model and hold a public hearing to motivate an increase of school meal funding. The results showed that local public policy has been motivated during 2009-2011 to increase school meal budget using local budgets. School children with best food consumption behavior and exercise increased from 13.2% in 2009 to 51.6% in 2013 and stunting decreased from 6.0% in 2009 to 4.7% in 2013. As the result of national policy motivation (2012-2013), the cabinet meeting on October 22, 2013 has approved an increase of school lunch budget from 0.40 USD to 0.62 USD per person per day. Thus, 5,800,469 school children nationwide have benefited from the budget increase.

Keywords: public policy, quality school lunch, Thailand, obesity

Procedia PDF Downloads 334

Authors: P. T. Ngan

Abstract:

Purpose: The study aims to answer the question what are motivational conditions that have great influences on employees’ innovative work behaviors by investigating the case of SATAMANKULMA/ Anya Productions Ky in Kuopio, Finland. Design/methodology: The main methodology utilized was the qualitative single case study research, analysis was conducted with an adapted thematic content analysis procedure, created from empirical material that was collected through interviews, observation and document review. Findings: The paper highlights the significance of combining relevant synergistic extrinsic and intrinsic motivations into the organizational motivation system. The findings show that intrinsic drives are essential for the initiation phases while extrinsic drives are more important for the implementation phases of innovative work behaviors. The study also offers the IDEA motivation model-interpersonal relationships & networks, development opportunities, economic constituent and application supports as an ideal tool to optimize business performance. Practical limitations/ implications: The research was only conducted from the perspective of SATAMANKULMA/Anya Productions Ky, with five interviews, a few observations and with several reviewed documents. However, further research is required to include other stakeholders, such as the customers, partner companies etc. Also the study does not offer statistical validity of the findings; an extensive case study or a qualitative multiple case study is suggested to compare the findings and provide information as to whether IDEA model relevant in other types of firms. Originality/value: Neither the innovation nor the human resource management field provides a detailed overview of specific motivational conditions might use to stimulate innovative work behaviors of individual employees. This paper fills that void.

Keywords: employee innovative work behaviors, extrinsic motivation, intrinsic motivation, organizational innovativeness

Procedia PDF Downloads 253