Search results for: low Young’s modulus

Authors: Dheyaa Wajid Abbood, Mohanad Salih Farhan, Awadh E. Ajeel

Abstract:

The basic goal of this study is the production of cheap building elements from plastic waste. environmentally friendly and of good thermal insulation. The study depends on the addition of plastic waste as aggregates to the mixes of concrete at different percentages by weight (12 percentages) to produce lightweight aggregate concrete the density (1095 - 1892) kg/m3.The experimental work includes 120 specimens of concrete 72 cubes (150*150*150)mm, 48 cylinder (150*300) mm. The results obtained for concrete were for local raw materials without any additional materials or treatment. The mechanical and thermal properties determined were (compressive strength, static modulus of elasticity, density, thermal conductivity (k), specific heat capacity (Cp), thermal expansion (α) after (7) days of curing at 20 0C. The increase in amount of plastic waste decreases the density of concrete which leads to decrease in the mechanical and to improvement in thermal properties. The average measured static modulus of elasticity are found less than the predicted static modulus of elasticity and splitting tensile strength (ACI 318-2008 and ACI 213R-2003). All cubes specimens when exposed to heat at (200, 400, 600 0C), the compressive strength of all mixes decreases gradually at 600 0C, the strength of lightweight aggregate concrete were disintegrated. Lightweight aggregate concrete is about 25% lighter than normal concrete in dead load, and to the improve the properties of thermal insulation of building blocks.

Keywords: LWAC, plastic waste, thermal property, thermal insulation

Procedia PDF Downloads 428

Authors: A. H. Yehia, M. M. Rashwan, K. A. Assaf, K. Abd el Samee

Abstract:

The aim of this work is to use an environmental, cheap; organic non-traditional admixture to improve the structural behavior of sustainable reinforced concrete beams contains different ratios of recycled concrete aggregate. The used admixture prepared by using wastes from vegetable oil industry. Under and over reinforced concrete beams made from natural aggregate and different ratios of recycled concrete aggregate were tested under static load until failure. Eight beams were tested to investigate the performance and mechanism effect of admixture on improving deformation characteristics, modulus of elasticity and toughness of tested beams. Test results show efficiency of organic admixture on improving flexural behavior of beams contains 20% recycled concrete aggregate more over the other ratios.

Keywords: deflection, modulus of elasticity, non-traditional admixture, recycled concrete aggregate, strain, toughness, under and over reinforcement

Procedia PDF Downloads 462

Authors: Kumator Taku, Bilkisu Amartey

Abstract:

This research used Grid indentation technique to investigate the effect of the addition of Coconut Shell Ash (CSA) on the nanomechanical properties of the main phases of the hydrated cement paste. Portland cement was partially replaced with 15% CSA at a water-binder ratio of 0.5 and cubes casted and cured for 28 days after which they were polished to reduce surface roughness to the barest minimum. The result of nanoindentation shows that addition of 15% CSA to cement paste transforms portlandite to C-S-H by the pozzolanic reaction. More so, there is reduced porosity and a reduction in the volume of CH by the addition of the CSA. Even though the addition of 15% CSA does not drastically change the average values of the hardness and elastic modulus of the two phases of the C-S-H, it greatly modifies their relative proportions, leading to the production of more HD C-S-H. Overall, incorporating 15%CSA to cement mortar improves the Nanomechanical properties of the four main phases of the hydrated cement paste.

Keywords: Coconut Shell Ash, Elastic Modulus, Hardness, Nanoindentation, Porosity

Procedia PDF Downloads 129

Authors: Baqir Rezai, Leila Heydarinasab, Rasol Roshan, Mohammad Ghulami

Abstract:

Introduction: The resilience process is one of the controversial and important subjects for child and youth immigrants throughout the world. Positive adaptation to the environment is a consequence of resilience which can affect the quality of life and physical and mental health among immigrants. Objective: A total of 714 Afghan young immigrants (14 to 18-years-old) who live in Iran for more than three years were entered into the study. A random sampling method was applied to obtain data. The study samples were divided into two groups (N1 =360 and N2=354) for exploratory and confirmation analysis. Exploratory factorial analysis was applied to confirm the construct validity of CYRM-28. Results: The results showed that this scale has useful validity content, and the study samples include three factors of individuals, context, and relational in child and youth resilience measure-28. However, from a total of 28 main items, only 15 items could identify these factors. Discussion: The resilience process among young immigrants is mainly explained by individuals, social and cultural conditions. For instance, young immigrants search the resilience process in conditions that caused their immigration. In this context, some questions about the content of security and personal promotion in society could identify three main factors.

Keywords: CYRM-28, factorial analysis, resilience, Afghan young immigrants

Procedia PDF Downloads 139

Authors: Vivi Anggraini, Afshin Asadi, Bujang B. K. Huat

Abstract:

Earth structures constructed of marine clay soils have tendency to crack. In order to improve the flexural strength and brittleness, a technique of mixing short fibers is introduced to the soil lime mixture. Coir fiber was used in this study as reinforcing elements. An experimental investigation consisting primarily of flexural tensile tests was conducted to examine the influence of coir fibers on the flexural behaviour of the reinforced soils. The test results demonstrated that the coir fibers were effective in improving the flexural strength and young’s modulus of all soils were examined and ductility after peak strength for reinforced marine clay soil was treated by lime. 5% lime treated soil and 1% coir fiber reinforced soil specimen’s demonstrated good strength and durability when submerged in water and retained 45% of their air-cured strengths.

Keywords: flexural strength, durabilty, lime, coir fibers, bending force, ductility

Procedia PDF Downloads 466

Authors: Athanasia Kouroupa

Abstract:

Existing research highlights the effect of employing robots in sessions with children and young people on the autism spectrum to develop and practice skills important to independent and functional living. The systematic review aimed to explore the way robots has been used with children and young people on the autism spectrum and the effect of using robots as a therapeutic interface. An electronic bibliographic database search using a combination of expressions was conducted. Data were extracted in relation to robot types, session characteristics, and outcomes and analysed using narrative synthesis. Forty studies were selected in the review. Humanoid robots were predominantly used to practice a range of social and communication skills. On average, children and young people on the autism spectrum had five sessions, twice a week, for approximately half an hour. Having sessions with a robot was commonly equal to or more effective than 'traditional' interventions delivered by a human therapist or having no therapy. The review reported encouraging outcomes to practice and develop a range of skills with children and young people on the autism spectrum. These findings suggest that some form of intervention is favourable over no intervention. However, there is little evidence for the relative effectiveness of the robot-based intervention as an innovative alternative option. Many of the studies had methodological weaknesses that make them vulnerable to bias. There is a need for further research that adheres to strict scientific methods making direct comparisons between different treatment options.

Keywords: autism, children, robots, outcomes

Procedia PDF Downloads 135

Authors: Abdalla Mohamed M. Musbahi

Abstract:

The study area lies in Al-Falah area on Airport-Tripoli in Zone (16) Where planned establishment of complex multi-floors for residential and commercial, this part was divided into seven subzone. In each sup zone, were collected Orthogonal profiles by using Seismic refraction method. The overall aim with this project is to investigate the applicability of Seismic refraction method is a commonly used traditional geophysical technique to determine depth-to-bedrock, competence of bedrock, depth to the water table, or depth to other seismic velocity boundaries The purpose of the work is to make engineers and decision makers recognize the importance of planning and execution of a pre-investigation program including geophysics and in particular seismic refraction method. The overall aim with this thesis is achieved by evaluation of seismic refraction method in different scales, determine the depth and velocity of the base layer (bed-rock). Calculate the elastic property in each layer in the region by using the Seismic refraction method. The orthogonal profiles was carried out in every subzones of (zone 16). The layout of the seismic refraction set up is schematically, the geophones are placed on the linear imaginary line whit a 5 m spacing, the three shot points (in beginning of layout–mid and end of layout) was used, in order to generate the P and S waves. The 1st and last shot point is placed about 5 meters from the geophones and the middle shot point is put in between 12th to 13th geophone, from time-distance curve the P and S waves was calculated and the thickness was estimated up to three-layers. As we know any change in values of physical properties of medium (shear modulus, bulk modulus, density) leads to change waves velocity which passing through medium where any change in properties of rocks cause change in velocity of waves. because the change in properties of rocks cause change in parameters of medium density (ρ), bulk modulus (κ), shear modulus (μ). Therefore, the velocity of waves which travel in rocks have close relationship with these parameters. Therefore we can estimate theses parameters by knowing primary and secondary velocity (p-wave, s-wave).

Keywords: application of seismic, geotechnical study, physical properties, seismic refraction

Procedia PDF Downloads 491

Authors: Bishnu Prasad Dulal, Sushil Chandra Baral, Radheshyam Bhattarai, Meera Tandan

Abstract:

Background: Non-use of contraceptives is a leading cause of unintended pregnancy. This study was done to explore the potential predictors of contraceptive used by young women, and the findings can inform policy makers to design the program to reduce unintended pregnancy for younger women who have a longer time of fecundity. Methodology: A nationally representative cross-sectional household survey was conducted by Health Research and Social Development Forum in 2012. Total 2259 currently married young women (15-24 years) were selected for the analysis out of 8578 women of reproductive age interviewed from the total 10260 households using systematic sampling. Binary logistic regression was used to identify factors associated with the use of modern contraceptive methods. Findings: The prevalence of modern contraceptive methods among young women was 25.2 %. Use of contraceptives was significantly associated with age at first marriage <15 year of age (OR:1.95) and ever delivered (OR: 1.8). Muslim women were significantly less likely to use contraceptives. Development region, wealth quintile, and awareness of abortion site were also statistically associated factors to use of contraceptives. Conclusion: The prevalence of contraceptives uses among young married women (25.2%) was lower than national prevalence (43%) of contraceptives use among married women of reproductive age. Our analysis focused on examining the association between women’s characteristics-related factors and use and nonuse of modern contraceptives. Awareness of safe abortion site is significantly associated while level of education was not. It is an interesting finding but difficult to interpret which needs further analysis on the basis of education. Maybe due to the underlying socio-religious practice of Muslim people, they had lower use of contraceptives. Programmers and policy makers could better help young women by increasing intervention activities to have a regular use of contraceptive-covering poor, Dalit and Muslim, and low aged women in order to reduce unintended pregnancy.

Keywords: unintended pregnancy, contraceptive, young women, Nepal

Procedia PDF Downloads 455

Authors: Amel Hamma, Allesandro Pegoretti

Abstract:

Kenaf fibres, with two aspect ratios, were melt compounded with two types of biopolymers named starch grafted polypropylene, and then blends compression molded to form plates of 1 mm thick. Results showed that processing induced variation of fibres length which is quantified by optical microscopy observations. Young modulus, stress at break and impact resistance values of starch-grafted-polypropylenes were remarkably improved by kenaf fibres for both matrixes and demonstrated best values when G906PJ were used as matrix. These results attest the good interfacial bonding between the matrix and fibres even in the absence of any interfacial modification. Vicat Softening Point and storage modules were also improved due to the reinforcing effect of fibres. Moreover, short-term tensile creep tests have proven that kenaf fibres remarkably improve the creep stability of composites. The creep behavior of the investigated materials was successfully modeled by the four parameters Burgers model.

Keywords: creep behaviour, kenaf fibres, mechanical properties, starch-grafted-polypropylene

Procedia PDF Downloads 230

Authors: F. Siahmed, A. Lounis, L. Faghi

Abstract:

The aim of this work is to study mechanical properties of composites based on fiber natural. This material has attracted attention of the scientific community for its mechanical properties, its moderate cost and its specification as regards the protection of environment. In this study the loofah part of the family of the natural fiber has been used for these significant mechanical properties. The fiber has porous structure, which facilitates the impregnation of the resin through these pores. The matrix used in this study is the type of unsaturated polyester. This resin was chosen for its resistance to long term.The work involves: -The chemical treatment of the fibers of loofah by NaOH solution (5%) -The realization of the composite resin / fiber loofah; The preparation of samples for testing -The tensile tests and bending -The observation of facies rupture by scanning electron microscopy The results obtained allow us to observe that the values of Young's modulus and tensile strength in tension is high and open up real prospects. The improvement in mechanical properties has been obtained for the two-layer composite fiber with 7.5% (by weight).

Keywords: loofah fiber, mechanical properties, composite, loofah fiber resin

Procedia PDF Downloads 447

Authors: Marta Czechowska-Bieluga

Abstract:

Social work education in Poland focuses mostly on developing competencies that address the needs of individuals and families affected by a variety of life's problems. As a result of the ageing of the Polish population, much attention is equally devoted to adults, including the elderly. However, social work with children and young people is the area of education which should be given more consideration. Social work students are mostly trained to cater to the needs of families and the competencies aimed to respond to the needs of children and young people do not receive enough attention and are only offered as elective classes. This paper strives to review the social work programmes offered by the selected higher education institutions in Poland in terms of social work training aimed at helping children and young people to address their life problems. The analysis conducted in this study indicates that university education for social work focuses on training professionals who will provide assistance only to adults. Due to changes in the social and political situation, including, in particular, changes in social policy implemented for the needy, it is necessary to extend this area of education to include the specificity of the support for children and young people; especially, in the light of the appearance of new support professions within the area of social work. For example, family assistants, whose task is to support parents in performing their roles as guardians and educators, also assist children. Therefore, it becomes necessary to equip social work professionals with competencies which include issues related to the quality of life of underage people living in families. Social work curricula should be extended to include the issues of child and young person development and the patterns governing this phase of life.

Keywords: social work education, social work programmes, social worker, university

Procedia PDF Downloads 289

Authors: WonSun Chen, James Boylan, Erwin Muharemovic, Denny Meyer

Abstract:

In Australia, drivers aged between 18 and 24 remained at high risk of road fatality over the last decade. Despite the successful implementation of the Graduated Licensing System (GLS) that supports young drivers in their early phases of driving, the road fatality statistics for these drivers remains high. In response to these statistics, studies conducted in Australia prior to the start of the COVID-19 pandemic have demonstrated the benefits of using telematics devices for improving driving behaviour, However, the impact of COVID-19 lockdown on young drivers’ driving behaviour has emerged as a global concern. Therefore, this naturalistic study aimed to evaluate and compare the driving behaviour(such as acceleration, braking, speeding, etc.) of young drivers with the adoption of in-vehicle telematics devices. Forty-two drivers aged between 18 and 30 and residing in the Australian state of Victoria participated in this study during the period of May to October 2022. All participants drove with the telematics devices during the first 30-day. At the start of the second 30-day, twenty-one participants were randomised to an intervention group where they were provided with an additional telematics ray device that provided visual feedback to the drivers, especially when they committed to aggressive driving behaviour. The remaining twenty-one participants remined their driving journeys without the extra telematics ray device (control group). Such trustworthy data enabled the assessment of changes in the driving behaviour of these young drivers using a machine learning approach in Python. Results are expected to show participants from the intervention group will show improvements in their driving behaviour compared to those from the control group.Furthermore, the telematics data enable the assessment and quantification of such improvements in driving behaviour. The findings from this study are anticipated to shed some light in guiding the development of customised campaigns and interventions to further address the high road fatality among young drivers in Australia.

Keywords: driving behaviour, naturalistic study, telematics data, young drivers

Procedia PDF Downloads 124

Authors: Runa Laila

Abstract:

In Bangladesh, migration and employment opportunities in the ready-made garment factories presented an alternative to early and arranged-marriage to many young women from the countryside. Although the positive impact of young women’s labour migration and employment in the garment industry on economic independence, increased negotiation power, and enhancement of self-esteem have been well documented, impact of employment on sexual norms and practices remained under-researched. This ethnographic study comprising of an in-depth interview of 21 single young women working in various garment factories in Gazipur, Dhaka, explores the implication of work on sexual norms and practices. This study found young single garment workers experience a range of consensual and coercive sexual relations. The mixed-sex work environment in the garment manufacturing industry and private housing arrangements provide young single women opportunities to develop romantic and sexual relationships in the transient urban space, which was more restricted in the rural areas. The use of mobile phones further aids lovers to meet in amusement parks, friends’ houses, or residential hotels beyond the gaze of colleagues and neighbors. Due to sexual double standard, men’s sexual advantage is seen as natural and accepted, while women are being blamed as immoral for being engaged in pre-marital sex. Although self-choice marriage and premarital relations reported to be common among garment workers, stigma related to premarital sex lead young single women to resort to secret abortion practices. Married men also use power position to lure women in a subordinate position in coerce sexual relations, putting their reproductive and psychological health at risk. To improve sexual and reproductive health and wellbeing of young female garment workers, it is important to understand these changing sexual practices which otherwise remain taboo in public health discourses.

Keywords: female migration, ready-made garment, reproductive health, sexual practice

Procedia PDF Downloads 186

Authors: A. Maria G. Melero, A. M. Senna, J. A. Domingues, M. A. Hausen, E. Aparecida R. Duek, V. R. Botaro

Abstract:

A hydrogel from cellulose acetate cross linked with ethylenediaminetetraacetic dianhydride (HAC-EDTA) was synthesized by our research group, and submitted to characterization and biological tests. Cytocompatibility analysis was performed by confocal microscopy using human adipocyte derived stem cells (ASCs). The FTIR analysis showed characteristic bands of cellulose acetate and hydroxyl groups and the tensile tests evidence that HAC-EDTA present a Young’s modulus of 643.7 MPa. The confocal analysis revealed that there was cell growth at the surface of HAC-EDTA. After one day of culture the cells presented spherical morphology, which may be caused by stress of the sequestration of Ca²⁺ and Mg²⁺ ions at the cell medium by HAC-EDTA, as demonstrated by ICP-MS. However, after seven days and 14 days of culture, the cells present fibroblastoid morphology, phenotype expected by this cellular type. The results give efforts to indicate this new material as a potential biomaterial for tissue engineering, in the future in vivo approach.

Keywords: cellulose acetate, hydrogel, biomaterial, cellular growth

Procedia PDF Downloads 195

Authors: A. A. Ajayi-Banji, M. A. Adegbile, T. D. Akpenpuun, J. Bello, O. Omobowale, D. A. Jenyo

Abstract:

Ceramic ware waste applicability as coarse aggregate was considered in this study for dense masonry unit production. The waste was crushed into 1.4 mm particle size and mixed with natural fine aggregate in the ratio 2:3. Portland ordinary cement, aggregate, and water mix ratio was 1:7:0.5. Masonry units produced were cured for 7, 21 and 28 days prior to compressive test. The result shows that curing age have a significant effect on all the compressive strength indices inspected except for Young’s modulus. Crushing force and the compressive strength of the ceramic-natural fine aggregate blocks increased by 11.7 – 54.7% and 11.6 – 59.2% respectively. The highest ceramic-natural fine block compressive strength at yield and peak, 4.97 MPa, was obtained after 21 days curing age. Ceramic aggregate introduced into the dense blocks improved the suitability of the blocks for construction purposes.

Keywords: ceramic ware waste, co-ballast, dense masonry unit, compressive strength, curing time

Procedia PDF Downloads 410

Authors: Alison Wilde, Stephen Millett

Abstract:

The cultural value of disabled people has largely been overlooked within forms of media and cultural analysis until the 1980s, when disabled people and disability studies highlighted the cultural misrecognition of disabled people and called for improved forms of cultural recognition and representation. Despite an increase in cultural analysis of representations of disabled people, much has been assumed about how images are read, and little work has been done on the value attributed to disabled people by media audiences and the viewing interests and encounters of film audiences. In particular, there has been little work on film reception, or on the way that young people interpret images of disability. We set out to understand some of the ways that young people read disability imagery, by showing small groups of young people different types of film featuring impairments, chosen from three different eras in film. These were Freaks, Rear Window (remake), and Finding Nemo. The discussions after these films allowed them to explore their own experiences of disability alongside the evolution of cultural representations; in so doing they discussed significant themes of cultural value and reflected on their own identities, e.g. in/dependency, autonomy, and competency and the ways these intersected with self-identity, and attitudes to disabled people.

Keywords: film, audience, identity, disability

Procedia PDF Downloads 419

Authors: Najmuddin Rasul

Abstract:

The purpose of this study is to determine whether media usage and change of citizenship norms influence trends of change of political participation of young voters in Indonesia. The focus of this study is to examine citizenship norms in the context of the development of information and communication technology influence political participation in the context of Indonesia's transition to democracy. The main theoretical framework is media and political participation. For data gathering, 384 young voters between the ages of 17 to 40 years were interviewed in Padang, West Sumatra, Indonesia. The results of this study reveal that gender, age and educational background of respondents did not influence significantly media usage and citizenship norms. The results also show that educational background is not a factor that distinguishes media usage but it becomes differentiating factor in citizenship norms. The results further show that media usage has a significant correlation with citizenship norms and citizenship norms has a significant relationship with political participation. In addition, media usage and citizenship norm significantly influence political participation. The sub-dimensions the citizenship norms (compliance, duty, and engaged citizenship) provides a significant contribution to the sub-dimensions of political participation (traditional political participation, modern political participation, civic political participation). Based on the findings it can be concluded that the political euphoria in the era of transition to democracy has changed pattern of media usage and citizenship norms among the young generation in Indonesia.

Keywords: political participation, media, citizenship norms, democracy, young voters, Indonesia

Procedia PDF Downloads 211

Authors: Rios A. S., Hild F., Deus E. P., Aimedieu P., Benallal A.

Abstract:

The damage micromechanisms of chopped strand mats manufactured by compression of Brazilian coconut fiber and coconut fibers in different external conditions (chemical treatment) were used in this study. Mechanical analysis testing uniaxial traction were used with Digital Image Correlation (DIC). The images captured during the tensile test in the coconut fibers and coconut fiber mats showed an uncertainty of measurement in order centipixels. The initial modulus (modulus of elasticity) and tensile strength decreased with increasing diameter for the four conditions of coconut fibers. The DIC showed heterogeneous deformation fields for coconut fibers and mats and the displacement fields showed the rupture process of coconut fiber. The determination of poisson’s ratio of the mat was performed through of transverse and longitudinal deformations found in the elastic region.

Keywords: coconut fiber, mechanical behavior, digital image correlation, micromechanism

Procedia PDF Downloads 459

Authors: Tillie Curran

Abstract:

This co-production project aimed for an expansive exploration of disabled young people’s hopes and dreams in the context of unprecedented societal changes. The research questions developed with disabled young people acting as peer researchers, ask ‘what does a good life look like now, and, what are your hopes and dreams for the future?’ Disabled children’s childhood studies and an asset-based approach placed the voice of disabled young people at the centre of the research process and inviting participants to ‘think big’! Over 18 months, academics, members of a Centre for Independent Living and peer researchers, came together to facilitate knowledge cafes with fifty disabled young people aged between 14 and 25 in a college and youth club setting. Methods used included trigger questions, photos voice, video, and cartooning. The peer researchers also investigated how house robots and connected autonomous vehicles might support their future aspirations and sense of freedom in this new era with a trip to the university robotic laboratory. Key themes arising from participants’ hopes and dream were about ‘being responsible’, ‘loving’, ‘freedom and happiness’ and a ‘strong sense of self and togetherness’ and suggest alternative narratives and rich visions of the future possibilities for disabled young people. The five key messages peer researchers produced for the report emphasised freedom to define their futures, desires to make the world a better place, to belong and have the chance of their own family life. Thematic analysis, production of the report and impact activities were all co-produced and as the project progressed peer researchers increasingly demonstrated a role as ‘change makers’ and have formed a young people’s co-production group going on into the future. Discussion of the project highlights the factors that made these processes successful and the ethical dilemmas encountered in the context of normalcy. Finally, we consider the implications for all involved as we rethink ‘the future’, not in terms of normative ideals or trajectories, or seeing service ‘transition’ as an end, but in terms of disabled young people’s contribution, participation, freedoms, and possibilities.

Keywords: co-production, disability, robotic, youth

Procedia PDF Downloads 129

Authors: Khaled Yahia

Abstract:

This paper deals with the problem of stator faults diagnosis in induction motors. Using the discrete wavelet transform (DWT) for the current Park’s vector modulus (CPVM) analysis, the inter-turn short-circuit faults diagnosis can be achieved. This method is based on the decomposition of the CPVM signal, where wavelet approximation and detail coefficients of this signal have been extracted. The energy evaluation of a known bandwidth detail permits to define a fault severity factor (FSF). This method has been tested through the simulation of an induction motor using a mathematical model based on the winding-function approach. Simulation, as well as experimental, results show the effectiveness of the used method.

Keywords: induction motors (IMs), inter-turn short-circuits diagnosis, discrete wavelet transform (DWT), current park’s vector modulus (CPVM)

Procedia PDF Downloads 569

Authors: Irfan Khan, Chiemeka David Ekene Arize, Hilly Swami, Suprabha Jha

Abstract:

Background: The rise of myocardial infarction (MI) among young adults, especially those with psychiatric conditions on antipsychotic medications, highlights the need to explore non-traditional cardiovascular risk factors. Case Presentation: We discuss a 24-year-old male with acute MI, diagnosed with an acute anxiety disorder, treated with risperidone and quetiapine, and with a history of occasional smoking. Despite no significant medical history, his presentation underscores the complex interactions between psychiatric conditions, antipsychotic medication, and lifestyle choices in the etiology of MI. Discussion: This case sheds light on the intricate relationship between minimal smoking habits, the use of atypical antipsychotics, and psychiatric illness as contributory factors to cardiovascular risk in young patients. It suggests a synergistic effect, amplifying the risk of MI, which is not adequately captured by traditional risk models. Conclusion: The case emphasizes the importance of an integrated care appro ach for young MI patients with psychiatric conditions and highlights the urgent need for further research to understand the compounded cardiovascular risk posed by psychiatric medications and lifestyle factors. It advocates for comprehensive risk assessments that consider these non-traditional factors to improve outcomes for this vulnerable patient population.

Keywords: myocardial infarction, young adults, psychiatric illness, antipsychotic medications, smoking

Procedia PDF Downloads 16

Authors: Aiswarea Mathew, Smita Mohanty, Jr., S. K. Nayak

Abstract:

Polyurethane networks based on castor oil (CO) as a renewable resource polyol were synthesized. Polyurethane/epoxy resin interpenetrating network nanocomposites containing modified montmorillonite organoclay (C30B-PU/EP nanocomposites) were prepared by an in situ intercalation method. The conventional spectroscopic characterization of the synthesized samples using FT-IR confirms the existence of the proposed castor oil based PU structure and also showed that strong interactions existed between C30B and EP/PU matrix. The dispersion degree of C30B in EP/PU matrix was characterized by X-Ray diffraction (XRD) method. Scanning electronic microscopy analysis showed that the interpenetrating process of PU and EP increases the exfoliation degree of C30B, and it improves the compatibility and the phase structure of polyurethane/epoxy resin interpenetrating polymer networks (PU/EP IPNs). The thermal stability improves compared to the polyurethane when the PU/EP IPN is formed. Mechanical properties including the Young’s modulus and tensile strength reflected marked improvement with addition of C30B.

Keywords: castor oil, epoxy, montmorillonite, polyurethane

Procedia PDF Downloads 400

Authors: Mohsin Talib Mohammed, Zahid A. Khan, Arshad N. Siddiquee

Abstract:

The wide use of titanium (Ti) materials in medicine gives impetus to a search for development new techniques with elevated properties such as strength, corrosion resistance and Young's modulus close to that of bone tissue. This article presents the most recent state of the art on the use of equal channel angular pressing (ECAP) technique in evolving mechanical characteristics of the ultrafine-grained bio-grade Ti materials. Over past few decades, research activities in this area have grown enormously and have produced interesting results, including achieving the combination of conflicting properties that are desirable for biomedical applications by severe plastic deformation (SPD) processing. A comprehensive review of the most recent work in this area is systematically presented. The challenges in processing ultrafine-grained Ti materials are identified and discussed. An overview of the biomedical Ti alloys processed with ECAP technique is given in this review, along with a summary of their effect on the important mechanical properties that can be achieved by SPD processing. The paper also offers insights in the mechanisms underlying SPD.

Keywords: mechanical properties, ECAP, titanium, biomedical applications

Procedia PDF Downloads 451

Authors: Merve Ak Efe

Abstract:

Youth branches in Turkey are one of the sub-fields where political ideologies are intersected with daily life practices. When the youth branches are examined within the framework of daily life practices, a social area can be defined where many types of capital turn into gains. The relationship between politics and capital is not only financial but can also be observed in the form of social, cultural, or emotional capital. This paper examines the political mobilization of young people who are members of the Youth Branch of the Justice and Development Party. The reason why JDP (Adalet ve Kalkınma Partisi) was chosen is that they have been the ruling party for twenty years, and there is a considerable number of young members within the party. Since Bayrampaşa is a district where JDP is politically active, This study is based on Bayrampaşa youth branches. The study examines how young people who are members of the party are mobilized and the everyday life practices and emotions underlying this mobilization. The data was collected through in-depth interviews with 13 young people, and the participant observation method was applied at the weekly meetings of the Justice and Development Party Bayrampaşa Youth Branch. Youth Branches represent a political space in which emotions turn into action for the young people who are involved in the party. During the field study at the micro level, it has been observed that the Bayrampaşa JDP Youth Branch hosted a transformation that incorporates political and social practices into modern tactics. One of the other results shows that being a member of youth branches causes a significant rise in social capital for young people. On the other hand, for the members with low cultural capital, there is an increase in social capital; however, an increase in cultural capital is not prominent.

Keywords: political mobilization, everyday practices, emotional capital, social capital, cultural capital

Procedia PDF Downloads 125

Authors: Shruti Soudi, Anushka Nayak

Abstract:

Altruism is a voluntary helping behavior that is not motivated by rewards. The empathy-altruism hypothesis states that altruistic behavior results from empathy, a constant emotional response between the helper and the individual in need. Individual variances in familiar ways of thinking, feeling, and acting are called personalities. The personality of an individual determines their behavior. More importantly, Adler was among the first psychologists to document the importance of birth order on personality. The present study aims to understand the influence of personality and birth order on altruism. A questionnaire consisting of standardized tools to measure altruism (Hindi Self Report Altruism Scale) and personality (Big Five Personality Inventory) will aid in studying the relationship between these variables among young adults in India. A statistical analysis of the data will be completed using ANOVA and T-Test in the SPSS Software.

Keywords: altruism, personality, birth order, ANOVA, young adults

Procedia PDF Downloads 77

Authors: H. Baltache, M. El Amine. Monir, R. Khenata, D. Rached, T. Seddik

Abstract:

The first principles calculations based on the density functional theory (DFT) by using the full-potential linearized augmented plane wave (FP-LAPW) method within the generalized gradient approximation (GGA) in order to investigate the structural and electronic properties of Cd1-xVxS alloy at x = 0.25 in zincblende structure. For the structural properties, we have calculated the equilibrium lattice parameters, such as lattice constant, bulk modulus and first pressure derivatives of the bulk modulus. From the electronic structure, we obtain that Cd0.75V0.25S alloy is nearly half-metallic. The analysis of the density of states (DOS) curves allow to evaluate the spin-exchange splitting energies Δx(d) and Δx(pd) that are generated by V-3d states, where the effective potential for spin-down case is attractive than for spin-up case. Calculations of the exchange constants N0α (valence band) and N0β (conduction band) are served to describe the magnetic behavior of the compounds.

Keywords: first-principles calculations, structural properties, electronic properties

Procedia PDF Downloads 365

Authors: Oyediran Wasiu Oyeleke

Abstract:

Melon is a popular economic cucurbit in Southwest, Nigeria. In recent time, many young farmers are shifting from melon to watermelon farming due to poor yield and low monetary returns. Hence, this study was carried out to assess the decline in melon yield and its contribution to young farmers’ diversification into watermelon farming in Oyo state, Nigeria. Purposive sampling technique was used in selecting 75 respondents from five villages in Ibarapa block of the Oyo State Agricultural Development Project (ADP). Data collected were analyzed using descriptive statistics and Pearson Product Moment Correlation (PPMC). Results show that majority of the respondents (77.3%) were between 31-40 years of age and 46.70% had secondary school education. Most of the respondents (80%) cultivated more than 3 ha of land for watermelon. Majority of the respondents (74.7%) intercropped melon with other crops while watermelon was cultivated as a sole crop. None of the respondents either grew improved melon seeds (certified seeds) or applied fertilizers but all respondents cultivated treated watermelon seeds, applied fertilizers, and agro-chemicals. The average yields of melon fell from 376.53kg/ha in 2009 to 280.70kg/ha in 2011. However, the respondents were shifting into watermelon production because of available quality seeds and its early maturity, easy harvest, and high sales. There was a significant relationship between melon output and young farmers’ diversification to watermelon in the study area at p < 0.05. The study concluded that decline in the melon yield discouraged youth to continue melon farming in the study area. It is hereby recommended that certified melon seeds should be made available while extension service providers should provide training support for the young farmers in order to reposition and boost melon production in the study area.

Keywords: decline, melon yield, contribution, watermelon, diversification, young farmers

Procedia PDF Downloads 186

Authors: Teju N. Adisa-Farrar

Abstract:

In European cities, social, political and cultural geographies of blackness exist. Organizations create spaces to discuss, express, and expose the realities of young people of African descent creating an Afropean lifestyle with transnational affiliations. Focusing on black and brown spaces produced by and for the young people of African descent in Vienna and Brussels, it became clear a multidisciplinary approach would be necessary. Using Cultural Studies frameworks along with Communications Theories on Black Public Spheres and Social-Geography, a basis was created for exploring the creative, political, and economic responses of young people who are apart of the historically (and contemporary) oppressed and excluded groups of the African Diaspora. Through this intrinsic study, it became apparent that spaces created and reclaimed by young people of the African Diaspora were more inclusive and democratic than other spaces. The organizations studied have used city life as the platform to express their struggles and celebrations of their multicultural identity; clearly using historical, global black and Pan-African movements as the basis for local adaptation of an African Diaspora identity.

Keywords: African diaspora, black public sphere, identity, spaces, geographies

Procedia PDF Downloads 293

Authors: Muhammad Akmal Putera, Noriyuki Yasufuku, Adel Alowaisy, Ahmad Rifai

Abstract:

Indonesia’s government has planned a project for a high-speed railway connecting the capital cities, Jakarta and Surabaya, about 700 km. Based on that location, it has been planning construction above the lowland soil region. The lowland soil region comprises cohesive soil with high water content and high compressibility index, which in fact, led to a settlement problem. Among the variety of railway track structures, the adoption of the ballastless track was used effectively to reduce the settlement; it provided a lightweight structure and minimized workspace. Contradictorily, deploying this thin layer structure above the lowland area was compensated with several problems, such as lack of bearing capacity and deflection behavior during traffic loading. It is necessary to combine with ground improvement to assure a settlement behavior on the clayey soil. Reflecting on the assurance of strength increment and working period, those were convinced by adopting methods such as cement-treated soil as the substructure of railway track. Particularly, evaluating mechanical properties in the field has been well known by using the plate load test and cone penetration test. However, observing an increment of mechanical properties has uncertainty, especially for evaluating cement-treated soil on the substructure. The current quality control of cement-treated soils was established by laboratory tests. Moreover, using small strain devices measurement in the laboratory can predict more reliable results that are identical to field measurement tests. Aims of this research are to show an intercorrelation of confining pressure with the initial condition of the Young modulus (E_o), Poisson ratio (υ_o) and Shear modulus (G_o) within small strain ranges. Furthermore, discrepancies between those parameters were also investigated. Based on the experimental result confirmed the intercorrelation between cement content and confining pressure with a power function. In addition, higher cement ratios have discrepancies, conversely with low mixing ratios.

Keywords: amount of cement, elastic zone, high-speed railway, lightweight structure

Procedia PDF Downloads 141

Authors: Roberta Ranielle M. de Freitas, Vagner R. Botaro

Abstract:

The relationship between biodegradation and mechanical behavior is fundamental for studies of the application of cellulose acetate films as a possible material for biodegradable packaging. In this work, the biodegradation of cellulose acetate (CA) with DS 2.5 was analyzed in simulated soil. CA films were prepared by casting and buried in the simulated soil. Samples were taken monthly and analyzed, the total time of biodegradation was 6 months. To characterize the biodegradable CA, the DMA technique was employed. The main result showed that the time of exposure to the simulated soil affects the mechanical properties of the films and the values of crystallinity. By DMA analysis, it was possible to conclude that as the CA is biodegraded, its mechanical properties were altered, for example, storage modulus has increased with biodegradation and the modulus of loss has decreased. Analyzes of DSC, XRD, and FTIR were also carried out to characterize the biodegradation of CA, which corroborated with the results of DMA. The observation of the carbonyl band by FTIR and crystalline indices obtained by XRD were important to evaluate the degradation of CA during the exposure time.

Keywords: biodegradation, cellulose acetate, DMA, simulated soil

Procedia PDF Downloads 218