Search results for: goods trade

Authors: Hsyi-En Cheng, Ying-Yi Liou

Abstract:

Metal-oxide semiconductor (MOS) gas sensors are widely used in the gas-detection market due to their high sensitivity, fast response, and simple device structures. However, the high working temperature of MOS gas sensors makes them difficult to integrate with the appliance or consumer goods. One-dimensional (1-D) nanostructures are considered to have the potential to lower their working temperature due to their large surface-to-volume ratio, confined electrical conduction channels, and small feature sizes. Unfortunately, the difficulty of fabricating 1-D nanostructure electrodes has hindered the development of low-temperature MOS gas sensors. In this work, we proposed a method to fabricate nanotube-arrays, and the SnO₂ nanotube-array sensors with different wall thickness were successfully prepared and examined. The fabrication of SnO₂ nanotube arrays incorporates the techniques of barrier-free anodic aluminum oxide (AAO) template and atomic layer deposition (ALD) of SnO₂. First, 1.0 µm Al film was deposited on ITO glass substrate by electron beam evaporation and then anodically oxidized by five wt% phosphoric acid solution at 5°C under a constant voltage of 100 V to form porous aluminum oxide. As the Al film was fully oxidized, a 15 min over anodization and a 30 min post chemical dissolution were used to remove the barrier oxide at the bottom end of pores to generate a barrier-free AAO template. The ALD using reactants of TiCl4 and H₂O was followed to grow a thin layer of SnO₂ on the template to form SnO₂ nanotube arrays. After removing the surface layer of SnO₂ by H₂ plasma and dissolving the template by 5 wt% phosphoric acid solution at 50°C, upright standing SnO₂ nanotube arrays on ITO glass were produced. Finally, Ag top electrode with line width of 5 μm was printed on the nanotube arrays to form SnO₂ nanotube-array sensor. Two SnO₂ nanotube-arrays with wall thickness of 30 and 60 nm were produced in this experiment for the evaluation of gas sensing ability. The flat SnO₂ films with thickness of 30 and 60 nm were also examined for comparison. The results show that the properties of ALD SnO₂ films were related to the deposition temperature. The films grown at 350°C had a low electrical resistivity of 3.6×10-3 Ω-cm and were, therefore, used for the nanotube-array sensors. The carrier concentration and mobility of the SnO₂ films were characterized by Ecopia HMS-3000 Hall-effect measurement system and were 1.1×1020 cm-3 and 16 cm3/V-s, respectively. The electrical resistance of SnO₂ film and nanotube-array sensors in air and in a 5% H₂-95% N₂ mixture gas was monitored by Pico text M3510A 6 1/2 Digits Multimeter. It was found that, at 200 °C, the 30-nm-wall SnO₂ nanotube-array sensor performs the highest responsivity to 5% H₂, followed by the 30-nm SnO₂ film sensor, the 60-nm SnO₂ film sensor, and the 60-nm-wall SnO₂ nanotube-array sensor. However, at temperatures below 100°C, all the samples were insensitive to the 5% H₂ gas. Further investigation on the sensors with thinner SnO₂ is necessary for improving the sensing ability at temperatures below 100 °C.

Keywords: atomic layer deposition, nanotube arrays, gas sensor, tin dioxide

Procedia PDF Downloads 216

Authors: S. Blanchard, D. Beladjine, K. Beddiar

Abstract:

Since 2015, the arrival of BIM in the building sector in France has turned the corporation world upside down. Not only constructive practices have been impacted, but also the uses and the men who have undergone important changes. Thus, the new collaborative mode generated by the BIM and the digital model has challenged the supremacy of some construction actors because the process involves working together taking into account the needs of other contributors. New BIM tools have emerged and actors in the act of building must take ownership of them. It is in this context that under the impetus of a European directive and the French government's encouragement of new missions and job profiles have. Moreover, concurrent engineering requires that each actor can advance at the same time as the others, at the whim of the information that reaches him, and the information he has to transmit. However, in the French legal system around public procurement, things are not planned in this direction. Also, a consequent evolution must take place to adapt to the methodology. The new missions generated by the BIM in France require a good mastery of the tools and the process. Also, to meet the objectives of the BIM approach, it is possible to define a typical job profile around the BIM, adapted to the various sectors concerned. The multitude of job offers using the same terms with very different objectives and the complexity of the proposed missions motivated by our approach. In order to reinforce exchanges with professionals or specialists, we carried out a statistical study to answer this problem. Five topics are discussed around the business area: the BIM in the company, the function (business), software used and BIM missions practiced (39 items). About 1400 professionals were interviewed. These people work in companies (micro businesses, SMEs, and Groups) of construction, engineering offices or, architectural agencies. 77% of respondents have the status of employees. All participants are graduated in their trade, the majority having level 1. Most people have less than a year of experience in BIM, but some have 10 years. The results of our survey help to understand why it is not possible to define a single type of BIM Manager. Indeed, the specificities of the companies are so numerous and complex and the missions so varied, that there is not a single model for a function. On the other hand, it was possible to define 3 main professions around the BIM (Manager, Coordinator and Modeler) and 3 main missions for the BIM Manager (deployment of the method, assistance to project management and management of a project).

Keywords: BIM manager, BIM modeler, BIM coordinator, project management

Procedia PDF Downloads 126

Authors: Akinola Helen Olufunke, Soetan Olatunbosun Jonathan, Adeleye Oludamola

Abstract:

Introduction: Antibiotic resistance has grown significantly, which is a major cause for concern. There have not been many significant developments in antibiotics over the past few decades, and practically all of the ones that are currently in use are losing effectiveness against pathogenic germs. Researchers are starting to focus more on the physiologically active compounds found in plants, particularly phytobiotics in poultry production. Consumption of chicken products is among the greatest in the country, but numerous nations, including Nigeria, use excessive amounts of necessary antibiotics in poultry farming, endangering the safety of such goods (through antimicrobial residues). Drug resistance has become a widespread issue as a result of the risky use of antibiotics in the chicken production industry. In order to replace antibiotics, biotic or natural products like phytobiotics (also known as botanicals or phytogenics) have drawn a lot of interest. Phytobiotics or their components are thought to be a relatively recent category of natural herbs that have acquired acceptance and favor among chicken farmers. The addition of several phytobiotic additions to poultry feed has demonstrated its capacity to improve both the broiler and layer populations' productivity. Design: Experimental research design and cross-sectional study was carried out at every 300 purposively selected farming household in the six-geopolitical zone in Nigeria. Data Analysis: A semi-structured questionnaire was administered to each farmer, and quantitative data were analyzed using Statistical Package for Social Science (SPSS) while the Chi-square test was used to analyze factors mitigating the use of Phytobiotics. Result: The result shows that the benefits associated with the use of phytobiotics are contributed to growth promotion in chickens and enhancement of productive performance of broiler and layer, which could be attributed to their antioxidant activity. The result further revealed that factors mitigating the use of phytobiotics were lack of knowledge in the use of phytobiotics, overdose or underdose usage, and seasonal availability of the phytobiotics. Others are the educational level of the farmers, intrinsic motivation, income poultry farming experience, price of phytobiotics based additives feeds, and intensity of extension agents in visiting them. Conclusion: The difficulties associated with using phytobiotics in chicken farms limit their willingness to boost productivity. The study found that most farmers were ignorant, which prevented them from handling this notion and turning their poultry into a viable enterprise while also allowing them to be creative. They believed that packing phytobiotics-based additive feed was expensive, and lastly, the seasonal availability of some phytobiotics. Recommendation: Further research in phytobiotics use in Nigeria should be carried out in order to establish its efficiency, safety, and awareness.

Keywords: mitigating, antibiotics, phytobiotics, poultry farming

Procedia PDF Downloads 145

Authors: Enayatollah Yazdani

Abstract:

In the post-Cold War era, the world is facing a new emerging global order with the rise of multiple actors in the international arena. China, as a rising global power, has great leverage in internal relations. In particular, during the last two decades, China has rapidly transformed its economy into a global leader in advanced technologies. As a rising power and as one of the two major founding members of the Shanghai Cooperation Organization (SCO), China has tried to use this regional organization, which has the potential to become an important political and security organization of the major states located in the vast Eurasian landmass, for its “go global” strategy. In fact, for Beijing, the SCO represents a new and unique cooperation model, reflecting its vision of a multipolar world order. China has used the SCO umbrella as a multilateral platform to address external threats posed by non-state actors on its vulnerable western border; to gain a strong economic and political foothold in Central Asia without putting the Sino-Russian strategic partnership at risk; and to enhance its energy security through large-scale infrastructure investment in, and trade with, the Central Asian member states. In other words, the SCO is one of the successful outcomes of Chines foreign policy in the post-Cold War era. The expansion of multilateral ties all over the world by dint of pursuing institutional strategies as SCO identifies China as a more constructive power. SCO became a new model of cooperation that was formed on the remains of collapsed Soviet system and predetermined China's geopolitical role in the region. As the fast developing effective regional mechanism, SCO now has more of an external impact on the international system and forms a new type of interaction for promoting China's grand strategy of 'peaceful rise.' This paper aims to answer this major question: How the Chinese government has manipulated the SCO for its foreign policy and global and regional influence? To answer this question, the main discussion is that with regard to the SCO capabilities and politico-economic potential, this organization has been used by China as a platform to expand influence beyond its borders.

Keywords: China, the Shanghai Cooperation Organization (SCO), Central Asia, global policy, foreign policy

Procedia PDF Downloads 46

Authors: S. Vaibhav Kant Sahu, Surabhi Bipin Seth

Abstract:

Human well-being has multiple constituents including the basic material for a good life, freedom and choice, health, good social relations, and security. Poverty is also multidimensional and has been defined as the pronounced deprivation of well-being. Dhurwa tribe of Bastar (India) have symbiotic relation with nature, it provisions ecosystem service such as food, fuel and fiber; regulating services such as climate regulation and non-material benefits such as spiritual or aesthetic benefits and they are managing their forest from ages. The demand for ecosystem services is now so great that trade-off among services become rule. Aim of study to explore evidences for linkages between ecosystem services and well-being of indigenous community, how much it helps them in poverty reduction and interaction between them. Objective of study was to find drivers of change and evidence concerning link between ecosystem, human development and sustainability, evidence in decision making does it opt for multi sectoral objectives. Which means human well-being as the central focus for assessment, while recognizing that biodiversity and ecosystems also have intrinsic value. Ecosystem changes that may have little impact on human well-being over days or weeks may have pronounced impacts over years or decades; so assessments needed to be conducted at spatial and temporal scales under social, political, economic scales to have high-resolution data. Researcher used framework developed by Millennium ecosystem assessment; since human action now directly or unknowingly virtually alter ecosystem. Researcher used ethnography study to get primary qualitative data, secondary data collected from panchayat office. The responses were transcribed and translated into English, as interview held in Hindi and local indigenous language. Focus group discussion were held with group of 10 women at Tiriya village. Researcher concluded with well-being is not just gap between ecosystem service supply but also increases vulnerability. Decision can have consequences external to the decision framework these consequences are called externalities because they are not part of the decision-making calculus.

Keywords: Bastar, Dhurwa tribe, ecosystem services, millennium ecosystem assessment, sustainability

Procedia PDF Downloads 276

Authors: Ming Gao, Matthew Tingchi Liu, Hoi Ngan Loi

Abstract:

Live streaming refers to the video contents generated by broadcasters and shared with viewers in real-time by uploading them to short-video platforms. In recent years, individual KOL broadcasters have successfully made use of live streams to sell a large amount of goods to the consumers. For example, Wei Ya, the Number 1 broadcaster in Taobao Live, sold products worth RMB 2.7 billion (USD 0.38 billion) in 2018. Regarding the success of live streaming commerce (LSC) in China, this study explores the elements of the booming LSC industry and attempts to explain the reasons behind its prosperity. A systematic review of industry reports and academic papers was conducted to summarize the latest findings in this field. And the results of this investigation showed that a live streaming eco-system has been established by the LSC players, namely, the platform, the broadcaster, the product supplier, and the viewer. In this eco-system, all players have complementary advantages and needs, and their close cooperation leads to a win-win situation. For instance, platforms and broadcasters have abundant internet traffic, which needs to be monetized, while product suppliers have mature supply chains and the need of promoting the products. In addition, viewers are attached to the LSC platforms to get product information, bargains, and entertainment. This study highlights the importance of the mass-personal hybrid communication nature of live streaming because its interpersonal communication feature increases consumers’ positive experiences, while its mass media broadcasting feature facilitates product promotion. Another innovative point of this study lies in its inclusion of the special characteristic of Chinese Internet culture - entertainment. The entertaining genres of the live streams created by broadcasters serve as down-to-earth approaches to reach their audiences easily. Further, the nature of video, i.e., the dynamic and salient stimulus, is emphasized in this study. Since video is more engaging, it can attract viewers in a quick and easy way. Meanwhile, the abundant, interesting, high-quality, and free short videos have added “stickiness” to platforms by retaining users and prolonging their staying time on the platforms. In addition, broadcasters’ important characters, such as physical attractiveness, humor, sex appeal, kindness, communication skills, and interactivity, are also identified as important factors that influence consumers’ engagement and purchase intention. In conclusion, all players have their own proper places in this live streaming eco-system, in which they work seamlessly to give full play to their respective advantages, with each player taking what it needs and offering what it has. This has contributed to the success of live streaming commerce in China.

Keywords: broadcasters, communication, entertainment, live streaming commerce, viewers

Procedia PDF Downloads 100

Authors: Arpita Banerjee

Abstract:

We now live in a world where half of the human population is city dwellers. The migration of people from rural to urban areas is rising continuously. But, the promise of a greater wage and better quality of life cannot keep up with the pace of migration. The rate of urbanization is much higher in developing countries. The UN predicts that 95 percent of this urban expansion will take place in the developing world in the next few decades. The population in the urban settlements of the developing nations is soaring, and megacities like Mumbai, Dhaka, Jakarta, Karachi, Manila, Shanghai, Rio de Janeiro, Lima, and Kinshasa are crammed with people, a majority of whom are migrants. Rural-urban migration has taken a new shape with the rising number of smaller cities. Apart from the increase in non-agricultural economic activities, growing demand for resources and energy, an increase in wastes and pollution, and a greater ecological footprint, there is another significant characteristic of the current wave of urbanization. This paper analyses that important marker of urbanization. It is the invisibility of production sites. The growing urban space ensures that the producers, the production sites, or the process stay beyond urban visibility. In cities and towns, living is majorly about earning money in either the informal service and small scale manufacturing sectors (a major part of which is food preparation), or the formal service sector. In the cases of both the informal service and small scale manufacturing or the formal service sector, commodity creation cannot be seen. The urban space happens to be the marketplace, where nature and its services, along with the non-urban labour, cannot be seen unless it is sold in the market. Hence, the consumers are now increasingly becoming disengaged from the producers. This paper compares the rate of increase in the size of and employment in the informal sector and/or that of the formal sector of some selected urban areas of India. Also, a comparison over the years of the aforementioned characteristics is presented in this paper, in order to find out how the anonymity of the producers to the urban consumers have grown as urbanization has risen. This paper also analyses the change in the transport cost of goods into the cities and towns of India and supports that claim made here that the invisibility of production is a crucial marker of modern-day urban-centric economic development. Such urbanization has an important ecological impact. The invisibility of the production site saves the urban consumer society from dealing with the ethical and ecological aspects of the production process. Once the real sector production is driven out of the cities and towns, the invisible ethical and ecological impacts of the growing urban consumption frees the consumers from associating themselves with any responsibility towards those impacts.

Keywords: ecological impact of urbanization, informal sector, invisibility of production, urbanization

Procedia PDF Downloads 108

Authors: Denise Levy, Anna Lucia C. H. Villavicencio

Abstract:

In a rapid-changing world, science teachers face considerable challenges. In addition to the basic curriculum, there must be included several transversal themes, which demand creative and innovative strategies to be arranged and integrated to traditional disciplines. In Brazil, nuclear science is still a controversial theme, and teachers themselves seem to be unaware of the issue, most often perpetuating prejudice, errors and misconceptions. This article presents the authors’ experience in the development of an interdisciplinary pedagogical proposal to include nuclear science in the basic curriculum, in a transversal and integrating way. The methodology applied was based on the analysis of several normative documents that define the requirements of essential learning, competences and skills of basic education for all schools in Brazil. The didactic materials and resources were developed according to the best practices to improve learning processes privileging constructivist educational techniques, with emphasis on active learning process, collaborative learning and learning through research. The material consists of an illustrated book for students, a book for teachers and a manual with activities that can articulate nuclear science to different disciplines: Portuguese, mathematics, science, art, English, history and geography. The content counts on high scientific rigor and articulate nuclear technology with topics of interest to society in the most diverse spheres, such as food supply, public health, food safety and foreign trade. Moreover, this pedagogical proposal takes advantage of the potential value of digital technologies, implementing QR codes that excite and challenge students of all ages, improving interaction and engagement. The expected results include the education of the educators for nuclear science communication in a transversal and integrating way, demystifying nuclear technology in a contextualized and significant approach. It is expected that the interdisciplinary pedagogical proposal contributes to improving attitudes towards knowledge construction, privileging reconstructive questioning, fostering a culture of systematic curiosity and encouraging critical thinking skills.

Keywords: science education, interdisciplinary learning, nuclear science, scientific literacy

Procedia PDF Downloads 104

Authors: Sana Iqbal

Abstract:

The female voice in Sufi poetry has been studied as a symbol of humility and devotion. Throughout the centuries, the Sufi shrines have also sheltered women and have served as a source of emotional strength in times of difficulty. Although women have been central to Sufi Islam, female-led rituals and performances (of veneration) are rarely studied as acts of empowerment and symbols of healing. This is especially true for rituals performed in informal spaces, which require going beyond the shrine practices. The rituals and meanings associated with Khizr Khwaja (or Sindhi Hindu god Jhelelal) among women in Punjab can serve as a useful case study to unpack some of these meanings. The paper aims to shed light on female-led rituals among women from Punjab associated with the folkloric traditions associated with Khizar Khwaja, Zinda Pir, Jhulelal or river god in the South Asian region to protect mariners from possible risks (since trade was primarily dependent on water channels) or for inducing timely rain date back to the 10th century in Sindh. However, these meanings and associations have evolved and the paper thus aims to establish a relationship between this figure and the women in Punjab by analysing the findings from an ethnographic study. It traces the historical meanings and significance attached to the divine figure and the wells (informal spaces) associated with him since the rituals performed by women is now infused solely with seeking fertility or to be blessed with a successful pregnancy, as opposed to him being celebrated for other reasons in older times. These associations beg the question of what women gain out of these rituals and making offerings to the mysterious figure of Khizr. Anecdotal evidence in the form of interviews conducted in Bhakar and Talwandi (Punjab) during the summer of 2015 helped to explore the stories related to this legend while also allowing us to witness some of the female-led ritual practices. It can be said that the symbols adopted in the ritual practices invoke liminality for women, which is a blend of opposites. The paper argues that this liminality/journey has been used as a vehicle to transcend all worldly structures of power and it symbolically emphasises the richness of feminine love/devotion and grants healing to female devotees.

Keywords: transgression, gender, liminality, ritual

Procedia PDF Downloads 93

Authors: Wilfred A. Abiaa, Chibundu N. Ezekiel, Benedikt Warth, Michael Sulyok, Paul C. Turner, Rudolf Krska, Paul F. Moundipa

Abstract:

Mycotoxins are a wide range of toxic secondary metabolites of fungi that contaminate various food commodities worldwide especially in sub-Saharan Africa (SSA). Such contamination seriously compromises food safety and quality posing a serious problem for human health as well as to trade and the economy. Their concentrations depend on various factors, such as the commodity itself, climatic conditions, storage conditions, seasonal variances, and processing methods. When humans consume foods contaminated by mycotoxins, they exert toxic effects to their health through various modes of actions. Rural populations in sub-Saharan Africa, are exposed to dietary mycotoxins, but it is supposed that exposure levels and health risks associated with mycotoxins between SSA countries may vary. Dietary exposures and health risk assessment studies have been limited by lack of equipment for the proper assessment of the associated health implications on consumer populations when they eat contaminated agricultural products. As such, mycotoxin research is premature in several SSA nations with product evaluation for mycotoxin loads below/above legislative limits being inadequate. Few nations have health risk assessment reports mainly based on direct quantification of the toxins in foods ('external exposure') and linking food levels with data from food frequency questionnaires. Nonetheless, the assessment of the exposure and health risk to mycotoxins requires more than the traditional approaches. Only a fraction of the mycotoxins in contaminated foods reaches the blood stream and exert toxicity ('internal exposure'). Also, internal exposure is usually smaller than external exposure thus dependence on external exposure alone may induce confounders in risk assessment. Some studies from SSA earlier focused on biomarker analysis mainly on aflatoxins while a few recent studies have concentrated on the multi-biomarker analysis of exposures in urine providing probable associations between observed disease occurrences and dietary mycotoxins levels. As a result, new techniques that could assess the levels of exposures directly in body tissue or fluid, and possibly link them to the disease state of individuals became urgent.

Keywords: mycotoxins, biomarkers, exposure assessment, health risk assessment, sub-Saharan Africa

Procedia PDF Downloads 542

Authors: Sikhumbuzo Zondi, Serges A. Kamga

Abstract:

Human security and human rights are mutually reinforcing concepts given that human security addresses questions related to human conditions such as the safety of individuals and the protection of individual rights and civil liberties. It does this by suggesting that the proper referent for security should be the individual and not the nation-state, due to the individual’s vulnerability to threats such as malnutrition and poverty, conflicts, exploitation and marginalization, despotism and climate change. Due to the primacy of the individual, human security comfortably expand to the notion of social justice, given that for far too-long, many individuals around the world have been denied of their basic human rights through racial discrimination, unfair labour and segregation policies and as a result encountered widespread social, environmental and economic injustices which are evident in the current structural division of the world between the developed north and the underdeveloped or developing south. In light of this view, ensuring freedom from want and freedom from fear, for all individuals is arguably the sound route to addressing and remedying the global ills of our time and a way to promoting human rights for all. The promotion of human security provides an important part of human/societal progress because inclusive security facilitates development and human rights protection, while insecurity reduces people’s growth and investment prospects and prolongs historical injustices. Therefore, this paper seeks to show that human security and human rights complements one another and that this correlation provides the necessary mechanisms for addressing and remedying the historical injustices that still affect most of the world’s population. It will look at linkages between human security and the individual right to equality and freedom from discrimination, right to life, liberty, and personal security; development; own property; adequate living standard; education; desirable work and to join trade unions; participate in government and in free elections; social security and equality before the law. The paper considers these human rights and liberties as vital for securing the core values of human life while at the same addressing socio-economic injustices that still persist in the contemporary world. The paper will be a desktop study using qualitative research methods on two case studies in Africa namely Cameroun and South Africa.

Keywords: justice, human security, human rights, injustices

Procedia PDF Downloads 147

Authors: Shabina Khan, Rukhsana Tabassum Syeda

Abstract:

Islamic banking is a finance system based on the principles of Shariah law. Charging interest is prohibited in Islam. Instead of charging interest the lender shares some part of profit or loss with the borrower, there is a great need for Islamic banking after the collapse of leading Wall Street institutions notably Lehman Brothers and other global finance institution, economic recession, Islamic banking have emerged as an alternative to conventional banking. Islamic banking is growing at the rate of more than 15% not only in Muslim countries, but also in secular and modern industrialized countries like U.K. Japan, France, Singapore, Hongkong. India with a total population of about 184 million about $ 1.5% Muslim deposit interest is lying unclaimed in different Indian banks, as there are no banks based on shariah laws approved by the RBI. When we take the example of Kerala state in India, almost 26.2% population is Muslim. Thus thousands of crore of rupees earned in interest is suspended accounts. In Kerala alone Rs. 40,000 crore and in Jammu and Kashmir Rs. 50,000 crore as interest earned on deposit of Muslim are lying unclaimed. By 2050, Indian Muslim population would be the largest in the world. It will surpass Indonesia. The Muslim population is likely to exceed 18% i.e. 310 mn. Muslim population will increase four percentage points from 14% to 18%. This paper studies the problems and prospects of Islamic banking in India. India has 29 states and Maharashtra is one of them. In the Maharashtra state is Aurangabad district. According to census 2011, Aurangabad city population is 51.07% is Hindu .Muslim is the second most popular religion with approximately 30.79. There are branches of Islamic banking run by Anjuman e Islam in many parts of India by the name of Al- Khair Baitul Mal which is a nongovernment organization. Its branch is in Aurangabad. The main objectives of this study are: 1. To find the scope of Islamic banking. 2. To study and analyze the prospects and problems of such organizations in Aurangabad district. 3. To create awareness about Islamic banking. 4. To study the functions of the organizations based on Islamic banking rules. 5. To encourage non-Muslims to invest in Islamic banking. The methodology used will be primary as well as secondary data. This is helping the weaker section of the society to obtain sources for trade and business. This paper finds that there is sufficient scope of Islamic banking in the region.

Keywords: Aurangabad, conventional banking, Islamic banking, Riba (interest)

Procedia PDF Downloads 225

Authors: Rajiv Kumar Srivastava

Abstract:

Manufacturing of complex products such as automobiles and computers requires a very large number of parts and sub-assemblies. The design of mechanisms for delivery of these materials to the point of assembly is an important manufacturing system and supply chain challenge. Different approaches to this problem have been evolved for assembly lines designed to make large volumes of standardized products. However, contemporary assembly systems are required to concurrently produce a variety of products using approaches such as mixed model production, and at times even mass customization. In this paper we examine the material supply approaches for variety production in moderate to large volumes. The conventional approach for material delivery to high volume assembly lines is to supply and stock materials line-side. However for certain materials, especially when the same or similar items are used along the line, it is more convenient to supply materials in kits. Kitting becomes more preferable when lines concurrently produce multiple products in mixed model mode, since space requirements could increase as product/ part variety increases. At times such kits may travel along with the product, while in some situations it may be better to have delivery and station-specific kits rather than product-based kits. Further, in some mass customization situations it may even be better to have a single delivery and assembly station, to which an entire kit is delivered for fitment, rather than a normal assembly line. Finally, in low-moderate volume assembly such as in engineered machinery, it may be logistically more economical to gather materials in an order-specific kit prior to launching final assembly. We have studied material supply mechanisms to support assembly systems as observed in case studies of firms with different combinations of volume and variety/ customization. It is found that the appropriate approach tends to be a hybrid between direct line supply and different kitting modes, with the best mix being a function of the manufacturing and supply chain environment, as well as space and handling considerations. In our continuing work we are studying these scenarios further, through the use of descriptive models and progressing towards prescriptive models to help achieve the optimal approach, capturing the trade-offs between inventory, material handling, space, and efficient line supply.

Keywords: assembly systems, kitting, material supply, variety production

Procedia PDF Downloads 198

Authors: Md Kamrul Hassan

Abstract:

Adaptation interventions are the common response to manage the vulnerabilities of climate change. The nature of adaptation intervention depends on the degree of vulnerability and the capacity of a society. The coping interventions can take the form of hard adaptation – utilising technologies and capital goods like dykes, embankments, seawalls, and/or soft adaptation – engaging knowledge and information sharing, capacity building, policy and strategy development, and innovation. Hard adaptation is quite capital intensive but provides immediate relief from climate change vulnerabilities. This type of adaptation is not real development, as the investment for the adaptation cannot improve the performance – just maintain the status quo of a social or ecological system, and often lead to maladaptation in the long-term. Maladaptation creates a two-way loss for a society – interventions bring further vulnerability on top of the existing vulnerability and investment for getting rid of the consequence of interventions. Hard adaptation is popular to the vulnerable groups, but it focuses so much on the immediate solution and often ignores the environmental issues and future risks of climate change. On the other hand, soft adaptation is education oriented where vulnerable groups learn how to live with climate change impacts. Soft adaptation interventions build the capacity of vulnerable groups through training, innovation, and support, which might enhance the resilience of a system. In consideration of long-term sustainability, soft adaptation can contribute more to resilience than hard adaptation. Taking a developing society as the study context, this study aims to investigate and understand the effectiveness of the adaptation interventions of the coastal community of Sundarbans mangrove forest in Bangladesh. Applying semi-structured interviews with a range of Sundarbans stakeholders including community residents, tourism demand-supply side stakeholders, and conservation and management agencies (e.g., Government, NGOs and international agencies) and document analysis, this paper reports several key insights regarding climate change adaptation. Firstly, while adaptation interventions may offer a short-term to medium-term solution to climate change vulnerabilities, interventions need to be revised for long-term sustainability. Secondly, soft adaptation offers advantages in terms of resilience in a rapidly changing environment, as it is flexible and dynamic. Thirdly, there is a challenge to communicate to educate vulnerable groups to understand more about the future effects of hard adaptation interventions (and the potential for maladaptation). Fourthly, hard adaptation can be used if the interventions do not degrade the environmental balance and if the investment of interventions does not exceed the economic benefit of the interventions. Overall, the goal of an adaptation intervention should be to enhance the resilience of a social or ecological system so that the system can with stand present vulnerabilities and future risks. In order to be sustainable, adaptation interventions should be designed in such way that those can address vulnerabilities and risks of climate change in a long-term timeframe.

Keywords: adaptation, climate change, maladaptation, resilience, Sundarbans, sustainability, vulnerability

Procedia PDF Downloads 167

Authors: Anna Cameron, Chunxia Zhao, Haofei Wang, Yun Liu, Guang Ze Yang

Abstract:

Since the first publication in 1775, cancer research has built a comprehensive understanding of how cellular components of the tumor niche promote disease development. However, only within the last decade has research begun to establish the impact of non-cellular components of the niche, particularly the extracellular matrix (ECM). The ECM, a three-dimensional scaffold that sustains the tumor microenvironment, plays a crucial role in disease progression. Cancer cells actively deregulate and remodel the ECM to establish a tumor-promoting environment. Recent work has highlighted the need to further our understanding of the complexity of this cancer-ECM relationship. In vitro models use hydrogels to mimic the ECM, as hydrogel matrices offer biological compatibility and stability needed for long term cell culture. However, natural hydrogels are being used in these models verbatim, without tuning their biophysical characteristics to achieve pathophysiological relevance, thus limiting their broad use within cancer research. The biophysical attributes of these gels dictate cancer cell proliferation, invasion, metastasis, and therapeutic response. Evaluating the three most widely used natural hydrogels, Matrigel, collagen, and agarose gel, the permeability, stiffness, and pore-size of each gel were measured and compared to the in vivo environment. The pore size of all three gels fell between 0.5-6 µm, which coincides with the 0.1-5 µm in vivo pore size found in the literature. However, the stiffness for hydrogels able to support cell culture ranged between 0.05 and 0.3 kPa, which falls outside the range of 0.3-20,000 kPa reported in the literature for an in vivo ECM. Permeability was ~100x greater than in vivo measurements, due in large part to the lack of cellular components which impede permeation. Though, these measurements prove important when assessing therapeutic particle delivery, as the ECM permeability decreased with increasing particle size, with 100 nm particles exhibiting a fifth of the permeability of 10 nm particles. This work explores ways of adjusting the biophysical characteristics of hydrogels by changing protein concentration and the trade-off, which occurs due to the interdependence of these factors. The global aim of this work is to produce a more pathophysiologically relevant model for each tumor type.

Keywords: cancer, extracellular matrix, hydrogel, microfluidic

Procedia PDF Downloads 68

Authors: Robert Kwame Kpaliba, Dennis Kpakpor Adotey, Yaw Serfor-Armah

Abstract:

Increase in the oceanic carbon dioxide absorbance from the atmosphere due to climate change has led to appreciable change in the chemistry of the oceans. The change in oceanic pH referred to as ocean acidification poses multiple threats and stresses on marine species, biodiversity, goods and services, and livelihoods. Marine ecosystems are continuously threatened by plethora of natural and anthropogenic stressors including carbon dioxide (CO₂) emissions causing a lot of changes which has not been experienced for approximately 60 years. Little has been done in Africa as a whole and Ghana in particular to improve the understanding of the variations of the carbonate chemistry of seawater and the biophysical impacts of ocean acidification on security of seafood, nutrition, climate and environmental change. There is, therefore, the need for regular monitoring of carbonate chemistry of seawater along Ghana’s coastline to generate reliable data to aid marine policy formulation. Samples of seawater were collected thrice every month for a one-year period from five study sites for the various parameters to be analyzed. Analysis of the measured physico-chemical and the carbonate chemistry parameters was done using simple statistics. Correlation test and ANOVA were run on both of the physico-chemical and carbonate chemistry parameters. The carbonate chemistry parameters were measured using computer software programme (CO₂cal v4.0.9) except total alkalinity and pH. The study assessed the variability of seawater carbonate chemistry in selected portions of the Central Atlantic Coastline of Ghana (Tsokomey/Bortianor, Kokrobitey, Gomoa Nyanyanor, Gomoa Fetteh, and Senya Breku landing beaches) over a 1-year period (June 2016–May 2017). For physico-chemical parameters, there was insignificant variation in nitrate (NO₃⁻) (1.62 - 2.3 mg/L), ammonia (NH₃) (1.52 - 2.05 mg/L), and salinity (sal) (34.50 - 34.74 ppt). Carbonate chemistry parameters for all the five study sites showed significant variation: partial pressure of carbon dioxide (pCO₂) (414.08-715.5 µmol/kg), carbonate ion (CO₃²⁻) (115-157.92 µmol/kg), pH (7.9-8.12), total alkalinity (TA) (1711.8-1986 µmol/kg), total carbon dioxide (TCO₂) (1512.1 - 1792 µmol/kg), dissolved carbon dioxide (CO₂aq) (10.97-18.92 µmol/kg), Revelle Factor (RF) (9.62-11.84), aragonite (ΩAr) (0.75-1.48) and calcite (ΩCa) (1.08-2.14). The study revealed that the partial pressure of carbon dioxide and temperature did not have a significant effect on each other (r² = 0.31) (p-value = 0.0717). There was an appreciable effect of pH on dissolved carbon dioxide (r² = 0.921) (p-value = 0.0000). The variation between total alkalinity and dissolved carbon dioxide was appreciable (r² = 0.731) (p-value = 0.0008). There was a significant correlation between total carbon dioxide and dissolved carbon dioxide (r² = 0.852) (p-value = 0.0000). Revelle factor correlated strongly with dissolved carbon dioxide (r² = 0.982) (p-value = 0.0000). Partial pressure of carbon dioxide corresponds strongly with atmospheric carbon dioxide (r² = 0.9999) (p-value = 0.00000).

Keywords: carbonate chemistry, seawater, central atlantic coastline, Ghana, ocean acidification

Procedia PDF Downloads 529

Authors: Iman Farasat, Howard M. Salis

Abstract:

The CRISPR/Cas9 system has revolutionized genome engineering by enabling site-directed and high-throughput genome editing, genome insertion, and gene knockdowns in several species, including bacteria, yeast, flies, worms, and human cell lines. This technology has the potential to enable human gene therapy to treat genetic diseases and cancer at the molecular level; however, the current CRISPR/Cas9 system suffers from seemingly sporadic off-target genome mutagenesis that prevents its use in gene therapy. A comprehensive mechanistic model that explains how the CRISPR/Cas9 functions would enable the rational design of the guide-RNAs responsible for target site selection while minimizing unexpected genome mutagenesis. Here, we present the first quantitative model of the CRISPR/Cas9 genome mutagenesis system that predicts how guide-RNA sequences (crRNAs) control target site selection and cleavage activity. We used statistical thermodynamics and law of mass action to develop a five-step biophysical model of cas9 cleavage, and examined it in vivo and in vitro. To predict a crRNA's binding specificities and cleavage rates, we then compiled a nearest neighbor (NN) energy model that accounts for all possible base pairings and mismatches between the crRNA and the possible genomic DNA sites. These calculations correctly predicted crRNA specificity across 5518 sites. Our analysis reveals that cas9 activity and specificity are anti-correlated, and, the trade-off between them is the determining factor in performing an RNA-mediated cleavage with minimal off-targets. To find an optimal solution, we first created a scheme of safe-design criteria for Cas9 target selection by systematic analysis of available high throughput measurements. We then used our biophysical model to determine the optimal Cas9 expression levels and timing that maximizes on-target cleavage and minimizes off-target activity. We successfully applied this approach in bacterial and mammalian cell lines to reduce off-target activity to near background mutagenesis level while maintaining high on-target cleavage rate.

Keywords: biophysical model, CRISPR, Cas9, genome editing

Procedia PDF Downloads 378

Authors: Jakub Berčík, Elena Horská, Ľudmila Nagyová

Abstract:

Nowadays, the point of sale remains one of the few channels of communication which is not oversaturated yet and has great potential for the future. The fact that purchasing decisions are significantly affected by emotions, while up to 75 % of them are implemented at the point of sale, only demonstrates its importance. The share of impulsive purchases is about 60-75 %, depending on the particular product category. Nevertheless, habits predetermine the content of the shopping cart above all and hence in this regard the role of in-store communication is to disrupt the routine and compel the customer to try something new. This is the reason why it is essential to know how to work with this relatively young branch of marketing communication as efficiently as possible. New global trend in this discipline is evaluating the effectiveness of particular tools in the in-store communication. To increase the efficiency it is necessary to become familiar with the factors affecting the customer both consciously and unconsciously, and that is a task for neuromarketing and sensory marketing. It is generally known that the customer remembers the negative experience much longer and more intensely than the positive ones, therefore it is essential for marketers to avoid this negative experience. The final effect of POP (Point of Purchase) or POS (Point of Sale) tools is conditional not only on their quality and design, but also on the location at the point of sale which contributes to the overall positive atmosphere in the store. Therefore, in-store advertising is increasingly in the center of attention and companies are willing to spend even a third of their marketing communication budget on it. The paper deals with a comprehensive, interdisciplinary research of the impact of traditional as well as innovative tools of in-store communication on the attention and emotional state (valence and arousal) of consumers on the food market. The research integrates measurements with eye camera (Eye tracker) and electroencephalograph (EEG) in real grocery stores as well as in laboratory conditions with the purpose of recognizing attention and emotional response among respondents under the influence of selected tools of in-store communication. The object of the research includes traditional (e.g. wobblers, stoppers, floor graphics) and innovative (e.g. displays, wobblers with LED elements, interactive floor graphics) tools of in-store communication in the fresh unpackaged food segment. By using a mobile 16-channel electroencephalograph (EEG equipment) from the company EPOC, a mobile eye camera (Eye tracker) from the company Tobii and a stationary eye camera (Eye tracker) from the company Gazepoint, we observe the attention and emotional state (valence and arousal) to reveal true consumer preferences using traditional and new unusual communication tools at the point of sale of the selected foodstuffs. The paper concludes with suggesting possibilities for rational, effective and energy-efficient combination of in-store communication tools, by which the retailer can accomplish not only captivating and attractive presentation of displayed goods, but ultimately also an increase in retail sales of the store.

Keywords: electroencephalograph (EEG), emotion, eye tracker, in-store communication

Procedia PDF Downloads 370

Authors: Mariam Begadze

Abstract:

Separation of Powers (SOP) has often been the most frequently posed objection against the judicial enforcement of socio-economic rights. Although a lot has been written to refute those, very rarely has it been assessed what effect the current practice of social rights adjudication has had on the construction of SOP doctrine in specific jurisdictions. Colombia is an appropriate case-study on this question. The notion of collaborative SOP in the 1991 Constitution has affected the court’s conception of its role. On the other hand, the trends in the jurisprudence have further shaped the collaborative notion of SOP. Other institutional characteristics of the Colombian constitutional law have played its share role as well. Tutela action, particularly flexible and fast judicial action for individuals has placed the judiciary in a more confrontational relation vis-à-vis the political branches. Later interventions through abstract review of austerity measures further contributed to that development. Logically, the court’s activism in this sphere has attracted attacks from political branches, which have turned out to be unsuccessful precisely due to court’s outreach to the middle-class, whose direct reliance on the court has turned into its direct democratic legitimacy. Only later have the structural judgments attempted to revive the collaborative notion behind SOP doctrine. However, the court-supervised monitoring process of implementation has itself manifested fluctuations in the mode of collaboration, moving into more managerial supervision recently. This is not surprising considering the highly dysfunctional political system in Colombia, where distrust seems to be the default starting point in the interaction of the branches. The paper aims to answer the question, what the appropriate judicial tools are to realize the collaborative notion of SOP in a context where the court has to strike a balance between the strong executive and the weak and largely dysfunctional legislative branch. If the recurrent abuse lies in the indifference and inaction of legislative branches to engage with political issues seriously, what are the tools in the court’s hands to activate the political process? The answer to this question partly lies in the court’s other strand of jurisprudence, in which it combines substantive objections with procedural ones concerning the operation of the legislative branch. The primary example is the decision on value-added tax on basic goods, in which the court invalidated the law based on the absence of sufficient deliberation in Congress on the question of the bills’ implications on the equity and progressiveness of the entire taxing system. The decision led to Congressional rejection of an identical bill based on the arguments put forward by the court. The case perhaps is the best illustration of the collaborative notion of SOP, in which the court refrains from categorical pronouncements, while does its bit for activating political process. This also legitimizes the court’s activism based on its role to counter the most perilous abuse in the Colombian context – failure of the political system to seriously engage with serious political questions.

Keywords: Colombian constitutional court, judicial review, separation of powers, social rights

Procedia PDF Downloads 82

Authors: Natalie Pomerantz, Nicholas Dugan, Molly Richards, Walter Zukas

Abstract:

The primary research question to be answered for Chemical/Biological (CB) protective clothing, is how to protect wearers from a range of chemical and biological threats in liquid, vapor, and aerosol form, while reducing the thermal burden. Currently, CB protective garments are hot, heavy, and wearers are limited by short work times in order to prevent heat injury. This study demonstrates how to incorporate different levels of protection on a material level and modify fabric composites such that the thermal burden is reduced to such an extent it approaches that of a standard duty uniform with no CB protection. CB protective materials are usually comprised of several fabric layers: a cover fabric with a liquid repellent coating, a protective layer which is comprised of a carbon-based sorptive material or semi-permeable membrane, and a comfort next-to-skin liner. In order to reduce thermal burden, all of these layers were laminated together to form one fabric composite which had no insulative air gap in between layers. However, the elimination of the air gap also reduced the CB protection of the fabric composite. In order to increase protection in the laminated composite, different nonwoven aerosol protective liners were added, and a super repellent coating was applied to the cover fabric, prior to lamination. Different adhesive patterns were investigated to determine the durability of the laminate with the super repellent coating, and the effect on air permeation. After evaluating the thermal properties, textile properties and protective properties of the iterations of these fabric composites, it was found that the thermal burden of these materials was greatly reduced by decreasing the thermal resistance with the elimination of the air gap between layers. While the level of protection was reduced in laminate composites, the addition of a super repellent coating increased protection towards low volatility agents without impacting thermal burden. Similarly, the addition of aerosol protective liner increased protection without reducing water vapor transport, depending on the nonwoven used, however, the air permeability was significantly decreased. The balance of all these properties and exploration of the trade space between thermal burden and protection will be discussed.

Keywords: aerosol protection, CBRNe protection, lamination, nonwovens, repellent coatings, thermal burden

Procedia PDF Downloads 335

Authors: A. M. Ferrari, L. Volpi, M. Pini, C. Siligardi, F. E. Garcia Muina, D. Settembre Blundo

Abstract:

A long tradition in the ceramic manufacturing since the 18th century, primarily due to the availability of raw materials and an efficient transport system, let to the birth and development of the Italian ceramic tiles district that nowadays represents a reference point for this sector even at global level. This economic growth has been coupled to attention towards environmental sustainability issues throughout various initiatives undertaken over the years at the level of the production sector, such as certification activities and sustainability policies. In this way, starting from an evaluation of the sustainability in all its aspects, the present work aims to develop a benchmarking helping both producers and consumers. In the present study, throughout the Life Cycle Sustainability Assessment (LCSA) framework, the sustainability has been assessed in all its dimensions: environmental with the Life Cycle Assessment (LCA), economic with the Life Cycle Costing (LCC) and social with the Social Life Cycle Assessment (S-LCA). The annual district production of stoneware tiles during the 2016 reference year has been taken as reference flow for all the three assessments, and the system boundaries cover the entire life cycle of the tiles, except for the LCC for which only the production costs have been considered at the moment. In addition, a preliminary method for the evaluation of local and indoor emissions has been introduced in order to assess the impact due to atmospheric emissions on both people living in the area surrounding the factories and workers. The Life Cycle Assessment results, obtained from IMPACT 2002+ modified assessment method, highlight that the manufacturing process is responsible for the main impact, especially because of atmospheric emissions at a local scale, followed by the distribution to end users, the installation and the ordinary maintenance of the tiles. With regard to the economic evaluation, both the internal and external costs have been considered. For the LCC, primary data from the analysis of the financial statements of Italian ceramic companies show that the higher cost items refer to expenses for goods and services and costs of human resources. The analysis of externalities with the EPS 2015dx method attributes the main damages to the distribution and installation of the tiles. The social dimension has been investigated with a preliminary approach by using the Social Hotspots Database, and the results indicate that the most affected damage categories are health and safety and labor rights and decent work. This study shows the potential of the LCSA framework applied to an industrial sector; in particular, it can be a useful tool for building a comprehensive benchmark for the sustainability of the ceramic industry, and it can help companies to actively integrate sustainability principles into their business models.

Keywords: benchmarking, Italian ceramic industry, life cycle sustainability assessment, porcelain stoneware tiles

Procedia PDF Downloads 98

Authors: Vikas Teotia, Sanjay Malhotra, Elina Mishra, Prashant Kumar, R. R. Singh, Priti Ukarde, P. P. Marathe, Y. S. Mayya

Abstract:

Bhabha Atomic Research Centre, Trombay is developing low energy high intensity Proton Accelerator (LEHIPA) as pre-injector for 1 GeV proton accelerator for accelerator driven sub-critical reactor system (ADSS). LEHIPA consists of RFQ (Radio Frequency Quadrupole) and DTL (Drift Tube Linac) as major accelerating structures. DTL is RF resonator operating in TM010 mode and provides longitudinal E-field for acceleration of charged particles. The RF design of drift tubes of DTL was carried out to maximize the shunt impedance; this demands the diameter of drift tubes (DTs) to be as low as possible. The width of the DT is however determined by the particle β and trade-off between a transit time factor and effective accelerating voltage in the DT gap. The array of Drift Tubes inside DTL shields the accelerating particle from decelerating RF phase and provides transverse focusing to the charged particles which otherwise tends to diverge due to Columbic repulsions and due to transverse e-field at entry of DTs. The magnetic lenses housed inside DTS controls the transverse emittance of the beam. Quadrupole magnets are preferred over solenoid magnets due to relative high focusing strength of former over later. The availability of small volume inside DTs for housing magnetic quadrupoles has motivated the usage of permanent magnet quadrupoles rather than Electromagnetic Quadrupoles (EMQ). This provides another advantage as joule heating is avoided which would have added thermal loaded in the continuous cycle accelerator. The beam dynamics requires uniformity of integral magnetic gradient to be better than ±0.5% with the nominal value of 2.05 tesla. The paper describes the magnetic design of the PMQ using Sm2Co17 rare earth permanent magnets. The paper discusses the results of five pre-series prototype fabrications and qualification of their prototype permanent magnet quadrupoles and a full scale DT developed with embedded PMQs. The paper discusses the magnetic pole design for optimizing integral Gdl uniformity and the value of higher order multipoles. A novel but simple method of tuning the integral Gdl is discussed.

Keywords: DTL, focusing, PMQ, proton, rate earth magnets

Procedia PDF Downloads 444

Authors: Vish Putcha, Chandrasekhar Putcha, Siva Hari

Abstract:

In the current digital era of free trading and pandemic-driven remote work culture, markets worldwide gained momentum for retail investors to trade from anywhere easily. The number of retail traders rose to 24% of the market from 15% at the pre-pandemic level. Most of them are young retail traders with high-risk tolerance compared to the previous generation of retail traders. This trend boosted the growth of subscription-based market predictors and market data vendors. Young traders are betting on these predictors, assuming one of them is correct. However, 90% of retail traders are on the losing end. This paper presents multiple indicators and attempts to derive behavioral patterns from the underlying stocks. The two major indicators that traders and investors follow are technical and fundamental. The famous investor, Warren Buffett, adheres to the “Value Investing” method that is based on a stock’s fundamental Analysis. In this paper, we present multiple indicators from various methods to understand the behavior patterns of stocks. For this research, we picked five stocks with a market capitalization of more than $200M, listed on the exchange for more than 20 years, and from different industry sectors. To study the behavioral pattern over time for these five stocks, a total of 8 indicators are chosen from fundamental, technical, and financial indicators, such as Price to Earning (P/E), Price to Book Value (P/B), Debt to Equity (D/E), Beta, Volatility, Relative Strength Index (RSI), Moving Averages and Dividend yields, followed by detailed mathematical Analysis. This is an interdisciplinary paper between various disciplines of Engineering, Accounting, and Finance. The research takes a new approach to identify clear indicators affecting stocks. Statistical Analysis of the data will be performed in terms of the probabilistic distribution, then follow and then determine the probability of the stock price going over a specific target value. The Chi-square test will be used to determine the validity of the assumed distribution. Preliminary results indicate that this approach is working well. When the complete results are presented in the final paper, they will be beneficial to the community.

Keywords: stock pattern, stock market analysis, stock predictions, trading, investing, fundamental analysis, technical analysis, quantitative trading, financial analysis, behavioral analysis

Procedia PDF Downloads 56

Authors: Evgeni Baratashvili, Giorgi Sulashvili, Malkhaz Sulashvili, Bela Khotenashvili, Irma Makharashvili

Abstract:

The most investment decision-making principle of regional travel firm's management and its partner is the formulation of the aims of investment programs. The investments can be targeted in order to reduce the firm's production costs and to purchase good transport equipment. In attractive region, in order to develop firm’s activities, the investment program can be targeted for increasing of provided services. That is the case where the sales already have been used in the market. The investment can be directed to establish the affiliate firms, branches, to construct new hotels, to create food and trade enterprises, to develop entertainment enterprises, etc. Economic development is of great importance to regional development. International experience shows that inclusive economic growth largely depends on not only the national, but also regional development planning and implementation of a strong and competitive regions. Regional development is considered as the key factor in achieving national success. Establishing a modern institute separate entities if the pilot centers will constitute a promotion, international best practice-based public-private partnership to encourage the use of models. Regional policy directions and strategies adopted in accordance with the successful implementation of major importance in the near future specific action plans for inclusive development and implementation, which will be provided in accordance with the effective monitoring and evaluation tools and measurable indicators combined. All of these above-mentioned investments are characterized by different levels, which are related to the following fact: How successful tourism marketing service is, whether it is able to determine the proper market's reaction according to the particular firm's actions. In the sphere of regional tourism industry and in the investment decision possible variants it can be developed the some specter of models. Each of the models can be modified and specified according to the situation, and characteristic skills of the existing problem that must be solved. Besides, while choosing the proper model, the process is affected by the regulation system of economic processes. Also, it is influenced by liberalization quality and by the level of state participation.

Keywords: net income of travel firm, economic growth, Investment profitability, regional development, tourist product, tourism development

Procedia PDF Downloads 238

Authors: Janice Haworth, Karamoko Camara, Marie-Therèse Dramou, Kokoly Haba, Daniel Léno, Augustin Mara, Adama Noël Oulari, Silafa Tolno, Noël Zoumanigui

Abstract:

The traditional rhythms of the West African country of Guinea have played a centuries-long role in defining the different people groups that make up the country. Throughout their history, before and since colonization by the French, the different ethnicities have used their traditional music as a distinct part of their historical identities. That is starting to change. Guinea is an impoverished nation created in the early twentieth-century with little regard for the history and cultures of the people who were included. The traditional rhythms of the different people groups and their heritages have remained. Fifteen individual traditional Guinean rhythms were chosen to represent popular rhythms from the four geographical regions of Guinea. Each rhythm was traced back to its native village and video recorded on-site by as many different local performing groups as could be located. The cyclical patterns rhythms were transcribed via a circular, spatial design and then copied into a box notation system where sounds happening at the same time could be studied. These rhythms were analyzed for their consistency-over-performance in a Fundamental Rhythm Pattern analysis so rhythms could be compared for how they are changing through different performances. The analysis showed that the traditional rhythm performances of the Middle and Forest Guinea regions were the most cohesive and showed the least evidence of change between performances. The role of music in each of these regions is both limited and focused. The Coastal and High Guinea regions have much in common historically through their ethnic history and modern-day trade connections, but the rhythm performances seem to be less consistent and demonstrate more changes in how they are performed today. In each of these regions the role and usage of music is much freer and wide-spread. In spite of advances being made as a country, different ethnic groups still frequently only respond and participate (dance and sing) to the music of their native ethnicity. There is some evidence that this self-imposed musical barrier is beginning to change and evolve, partially through the development of better roads, more access to electricity and technology, the nation-wide Ebola health crisis, and a growing self-identification as a unified nation.

Keywords: cultural identity, Guinea, traditional rhythms, west Africa

Procedia PDF Downloads 363

Authors: Dongshuo Wang, Minjie Xing

Abstract:

International businesses prefer to hire people who speak more than one language. With the booming of China’s market, industries and trade, business leaders are looking for people who can speak Chinese and operate successfully in a Chinese cultural context, and therefore an increasing number of tertiary students choose a Business Chinese (BC) course. As a result, BC syllabus design is urgently needed. What business knowledge should be included in China’s context? What aspects of BC culture should be included? How much Chinese language should be introduced to conduct business in China? With these research questions, this research explores a syllabus design that integrates the three aspects of subject knowledge of business in communication, business practice including the procedure of and strategies for communicating business in practice and language skills including the disciplinary and professional contexts in which linguistic choices are made. After literature review and consultancy with China-related business professionals, senior staff from business schools and representatives of students, the authors of this paper, together with language tutors drafted a syllabus based on the integrated approach to include subject knowledge, business practice and language skills. Due to the nature of this research which requires trial/test and detailed description for each correction, qualitative methods are adopted. Two in-depth focus group interviews (with 2 staff and 4 students in each group), and 18 individual interviews (8 staff and 10 students) were conducted. QDA was used for systematizing, organizing, and analysing qualitative data. It was discovered that the business knowledge related to a Chinese cultural context, including face value, networking skills, strategic plans for signing a contract, marketing, sales, and after-sale service, should be introduced through lectures and seminars; business practice could be implemented by students setting up their own companies, virtual or real; and language skills would be trained via writing business messages and presenting their companies in fairs and exhibitions. After a longitudinal study of trials and amendments for three years from 2013 to 2016, the syllabus was approved by staff and students and the university. Students appreciated the syllabus, as they could apply the subject knowledge into practice by using it in their own companies and Chinese language was used throughout the process. The syllabus is now ready to be used in universities offering BC, and the designing process can be applied to other new courses as well.

Keywords: business Chinese, syllabus design, business knowledge, language skills

Procedia PDF Downloads 322

Authors: Saikat Majumdar, D. C. Kalita

Abstract:

The Agriculture sector plays an important role in the rural economy of India. It is the backbone of our Indian economy and is the dominant sector in terms of employment and livelihood. Agriculture still contributes significantly to export earnings and is an important source of raw materials as well as of demand for many industrial products particularly fertilizers, pesticides, agricultural implements and a variety of consumer goods, etc. The performance of the agricultural sector influences the growth of Indian economy. According to the 2011 Agricultural Census of India, an estimated 61.5 percentage of rural populations are dependent on agriculture. Proper Agricultural infrastructure has the potential to transform the existing traditional agriculture into a most modern, commercial and dynamic farming system in India through its diffusion of technology. The rate of adoption of modern technology reflects the progress of development in agricultural sector. The adoption of any improved agricultural technology is also dependent on the development of road infrastructure or road network. The present study was consisting of 300 sample farmers out which 150 samples was taken from the developed area and rest 150 samples was taken from underdeveloped area. The samples farmers under develop and underdeveloped areas were collected by using Multistage Random Sampling procedure. In the first stage, North 24 Parganas District have been selected purposively. Then from the district, one developed and one underdeveloped block was selected randomly. In the third phase, 10 villages have been selected randomly from each block. Finally, from each village 15 sample farmers was selected randomly. The extents of adoption of technology in different areas were calculated through various parameters. These are percentage area under High Yielding Variety Cereals, percentage area under High Yielding Variety pulses, area under hybrids vegetables, irrigated area, mechanically operated area, amount spent on fertilizer and pesticides, etc. in both developed and underdeveloped areas of North 24 Parganas District, West Bengal. The percentage area under High Yielding Variety Cereals in the developed and underdeveloped areas was 34.86 and 22.59. 42.07 percentages and 31.46 percentages for High Yielding Variety pulses respectively. In the case the area under irrigation it was 57.66 and 35.71 percent while for the mechanically operated area it was 10.60 and 3.13 percent respectively in developed and underdeveloped areas of North 24 Parganas district, West Bengal. It clearly showed that the extent of adoption of technology was significantly higher in the developed area over underdeveloped area. Better road network system helps the farmers in increasing his farm income, farm assets, cropping intensity, marketed surplus and the rate of adoption of new technology. With this background, an attempt is made in this paper to study the impact of Agricultural Infrastructure on the adoption of modern technology in agriculture in North 24 Parganas District, West Bengal.

Keywords: agricultural infrastructure, adoption of technology, farm income, road network

Procedia PDF Downloads 79

Authors: Caroline Provost, Francois Dumont

Abstract:

Production of insects for human and animal consumption is an increasingly important activity in Canada. Protein production is more efficient and less harmful to the environment using insect rearing compared to the impact of traditional livestock, poultry and fish farms. Insects are rich in essential amino acids, essential fatty acids and trace elements. Thus, insect-based products could be used as a food supplement for livestock and domestic animals and may even find their way into the diets of high performing athletes or fine dining. Nevertheless, several parameters remain to be determined to ensure efficient and profitable production that meet the potential of these sectors. This project proposes to improve the production processes, rearing diets and processing methods for three species with valuable gastronomic and nutritional potential: the common mealworms (Tenebrio molitor), the small mealworm (Alphitobius diaperinus), and the giant mealworm (Zophobas morio). The general objective of the project is to acquire specific knowledge for mass rearing of insects dedicated to animal and human consumption in order to respond to current market opportunities and meet a growing demand for these products. Mass rearing of the three species of mealworm was produced to provide the individuals needed for the experiments. Mealworms eat flour from different cereals (e.g. wheat, barley, buckwheat). These cereals vary in their composition (protein, carbohydrates, fiber, vitamins, antioxidant, etc.), but also in their purchase cost. Seven different diets were compared to optimize the yield of the rearing. Diets were composed of cereal flour (e.g. wheat, barley) and were either mixed or left alone. Female fecundity, larvae mortality and growing curves were observed. Some flour diets have positive effects on female fecundity and larvae performance while each mealworm was found to have specific diet requirements. Trade-offs between mealworm performance and costs need to be considered. Experiments on the effect of flour composition on several parameters related to performance and nutritional and gastronomic value led to the identification of a more appropriate diet for each mealworm.

Keywords: mass rearing, mealworm, human consumption, diet

Procedia PDF Downloads 113

Authors: Natalia Carolina Encalada Castillo

Abstract:

As part of an intended radical policy change compared to former administrations in Ecuador, the transformation of the institutionality of international cooperation during the period of President Rafael Correa was considered as a key element for the construction of the state of 'Good Living'. This intention led to several regulatory changes in the reception of cooperation for development, and even the departure of some foreign cooperation agencies. Moreover, Ecuador launched the initiative to become a donor of cooperation towards other developing countries through the ‘South-South Cooperation’ approach. All these changes were institutionalized through the Ecuadorian System of International Cooperation as a new framework to establish rules and policies that guarantee a sovereign management of foreign aid. Therefore, this research project has been guided by two questions: What were the factors that motivated the transformation of the institutionality of international cooperation in Ecuador from 2007 to 2017? and, what were the implications of this transformation in terms of the international role of the country? This paper seeks to answer these questions through Role Theory within a Constructivist meta-theoretical perspective, considering that in this case, changes at the institutional level in the field of cooperation, responded not only to material motivations but also to interests built on the basis of a specific state identity. The latter was only possible to affirm through specific roles such as ‘sovereign recipient of cooperation’ as well as ‘donor of international cooperation’. However, the performance of these roles was problematic as they were not easily accepted by the other actors in the international arena or in the domestic level. In terms of methodology, these dynamics are analyzed in a qualitative way mainly through interpretive analysis of the discourse of high-level decision-makers from Ecuador and other cooperation actors. Complementary to this, document-based research of relevant information as well as interviews have been conducted. Finally, it is concluded that even if material factors such as infrastructure needs, trade and investment interests, as well as reinforcement of state control and monitoring of cooperation flows, motivated the institutional transformation of international cooperation in Ecuador; the essential basis of these changes was the search for a new identity for the country to be projected in the international arena. This identity started to be built but continues to be unstable. Therefore, it is important to potentiate the achievements of the new international cooperation policies, and review their weaknesses, so that non-reimbursable cooperation funds received as well as ‘South-South cooperation’ actions, contribute effectively to national objectives.

Keywords: Ecuador, international cooperation, Role Theory, state identity

Procedia PDF Downloads 172

Authors: Selinda England, Ben Bodnaryk

Abstract:

With an unprecedented increase in provincial immigration and government support for greater international and culturally diverse learners, a trade/applied learning-focused polytechnic with four campuses within one Canadian province saw the need for intercultural awareness and an intercultural teaching competence strategy for faculty training. An institution-wide pre-assessment needs survey was conducted in 2018, in which 87% of faculty professed to have some/no training when working with international and/or culturally diverse learners. After researching fellow Polytechnics in Canada and seeing very little in the way of faculty support for intercultural competence, an institutional project team comprised of members from all facets of the Polytechnic was created and included: Indigenous experts, Academic Chairs, Directors, Human Resource Managers, and international/settlement subject matter experts. The project team was organized to develop and implement a new academic model focused on enriching intercultural competence among faculty. Utilizing a competency based model, the project team incorporated inclusive terminology into competency indicators and devised a four-phase proposal for implementing intercultural teacher training: a series of workshops focused on the needs of international and culturally diverse learners, including teaching strategies based on current TESOL methodologies, literature and online resources for quick access when planning lessons, faculty assessment examples and models of interculturally proficient instructors, and future job descriptions - all which promote and encourage development of specific intercultural skills. Results from a post-assessment survey (to be conducted in Spring 2020) and caveats regarding improvements and next steps will be shared. The project team believes its intercultural and inclusive teaching competency-based model is one of the first, institution-wide faculty supported initiatives within the Canadian college and Polytechnic post-secondary educational environment; it aims to become a leader in both the province and nation regarding intercultural competency training for trades, industry, and business minded community colleges and applied learning institutions.

Keywords: cultural diversity and education, diversity training teacher training, teaching and learning, teacher training

Procedia PDF Downloads 88