Search results for: destructive PFAS treatment technology

Authors: I. Miličević, M. Hadzima Nyarko, R. Bušić, J. Simonović Radosavljević, M. Prokopijević, K. Vojisavljević

Abstract:

This paper investigates the effects of different treatment methods of rubber aggregates for self-compacting concrete (SCC) on compressive strength and modulus of elasticity. SCC mixtures with 10% replacement of fine aggregate with crumb rubber by total aggregate volume and with different aggregate treatment methods were investigated. The rubber aggregate was treated in three different methods: dry process, water-soaking, and NaOH treatment plus water soaking. Properties of SCC in a fresh and hardened state were tested and evaluated. Scanning electron microscope (SEM) analysis of three different SCC patches were made and discussed. It was observed that applying the proposed NaOH plus water soaking method resulted in the improvement of fresh and hardened concrete properties. It resulted in a more uniform distribution of rubber particles in the cement matrix, a better bond between rubber particles and the cement matrix, and higher compressive strength of SCC rubberized concrete.

Keywords: compressive strength, modulus of elasticity, NaOH treatment, rubber aggregate, self-compacting rubberized concrete, scanning electron microscope analysis

Procedia PDF Downloads 109

Authors: Mehmet Kale, Ramazan Sencan, Sibel Yavru, Ahmet Ak, Nuri Mamak, Sibel Hasırcıoglu, Mesih Kocamuftuoglu, Yakup Yıldırım, Hasbi Sait Saltık

Abstract:

Bovine Papilloma Virus (BPV)-induced warts can cause mastitis, teat blindness, reduction of milk yield, udder deformities, and a difficulty in getting the teats into the milking machine. Especially, surgical operations cannot be performed in BPV-induced teat warts because of the increased sensitivity of the breast region and small-sized papillomas. Thus, there is a need to find new topical treatment methods. We have developed a pomade for treatment of BPV in cattle. The pomade is consists of lanoline, snakeskin (two special kind of snake), alcohol, vaseline, and ether. Firstly, we determined 46 cattle with teat warts. In the study, BPV antigen was detected in 28 cattle blood samples (61%) by ELISA. The pomade was applied to all BPV infected animals. The regression and recovery of warts were 100% in all animals. We advised using the pomade for treatment of BPV-induced warts in teats.

Keywords: bovine papilloma virus, pomade, teat, udder

Procedia PDF Downloads 225

Authors: Ahmed Ali Samejo, Riffat Sultana

Abstract:

Pakistan has the sandy Thar Desert in the eastern area, which share border line with India and has exotic fauna and flora, the livelihood of native people rely on livestock and rain fed cultivated fields. The climate of Thar Desert is very harsh and stressful due to frequent drought and very little rainfall, which may occur during monsoon season in the months of July to October and temperature is high, and wind speed also increases in April to June. Schistocerca gregaria is a destructive pest of vegetation from Mauritania to the border line of Pakistan and India. Sometimes they produce swarms which consume all plant where ever they land down and cause the loss in agro-economy of the world. During the recent study, we observed that vegetation was not unique throughout the Thar Desert in the year 2015, because the first spell of rainfall showered over all areas of the Thar Desert in July. However, the second and third spell of rain was confined to village Mahandre jo par and surroundings from August to October. Consequently, vegetation and cultivated crops grew up specially bajra crop (Pennistum glaucum). The climate of Mahandre jo par and surroundings became favorable for S.gregaria, and remaining areas of Thar Desert went hostile. Therefore desert locust attracted to the pleasant area (Mahandre jo par and surroundings) and gradually concentrated, increased reproductive activities, but did not gregarize due to the harvest of bajra crop and the onset of the winter season with an immediate decrease in temperature. An outbreak was near to come into existence, and thereupon conditions become stressful for hoppers to continue further development. Afore mentioned was one reason behind hurdle to the outbreak, another reason might be that migration and concentration of desert locust took place at the end of the season, so climate becomes unfavorable for hoppers, due to dryness of vegetation. Soils also become dry, because rainfall was not showered in end of the season, that’s why eggs that were deposited in late summer were desiccated. This data might be proved fruitful to forecast any outbreak update in future.

Keywords: agro-economy, destructive pest, climate, outbreak, vegetation

Procedia PDF Downloads 172

Authors: Ahmad Masduki Bin Selamat

Abstract:

Malaysia is becoming a developed country by the year 2020, the problem is that little is known about the perceptions and curricular values of Malaysian high school students who have taken Living Skills as a subject in the regular public school. How these students perceive technology in their daily lives, in the country’s development and in global context, is not known. The study involved form 4 students from four public schools in Petaling District. The study found that the Petaling District students’ knowledge of technology were good, where 76.6 % of them scored 50% marks and above during the achievement test. In addition, it was also found that only excellent and squatter students perceived technology education as important as a school subject, compared to those students from the urban area. It was found that students preferred business and entrepreneurship topics rather than the other Living Skills curriculum. The study suggests that students should be exposed to technology education from the early years of schooling (preschool to secondary). In addition, the acquisition of skills, the evaluation, revision and modification of the instruction as well as the curriculum should be enforced.

Keywords: technology education, living skills, curricular values, public schools

Procedia PDF Downloads 453

Authors: Lin Zou

Abstract:

This paper explores how the development of science and technology in the recent decades has created new conditions for literature and aesthetics. These are epistemological conditions that not only offer empirical understandings of the human mentality, behavior, emotions, and humanity in general, but reshape how value and the ontological questions are understood and linked with humanity. This paper will discuss the implications of these epistemological conditions for the depiction and interpretation of human subjectivity in literature. The paper will first seek to present the argument that science and technology have created new conditions for literature and aesthetics. It then outlines the implications of these new conditions for literature and aesthetics. The main methodologies used are close reading and case studies.

Keywords: epistemological conditions, literature and aesthetics, science and technology, subjectivity

Procedia PDF Downloads 115

Authors: Ciro Cursio, Pio Luigi Cursio, Giulia Cursio, Isabella Chiardi, Luigi Cursio

Abstract:

Introduction: Full-face aesthetic treatments often present a difficult task: since different patients possess different anatomical and tissue characteristics, there is no guarantee that the same treatment will have the same effect on multiple patients; additionally, full-face rejuvenation and beautification treatments require not only a high degree of technical skill but also the ability to choose the right product for each area and a keen artistic eye. Method: We present an artificial intelligence-based algorithm that can generate realistic post-treatment 3D models based on the patient’s requests together with the doctor’s input. These 3-dimensional predictions can be used by the practitioner for two purposes: firstly, they help ensure that the patient and the doctor are completely aligned on the expectations of the treatment; secondly, the doctor can use them as a visual guide, obtaining a natural result that would normally stem from the practitioner's artistic skills. To this end, the algorithm is able to predict injection zones, the type and quantity of hyaluronic acid, the injection depth, and the technique to use. Results: Our innovation consists in providing an objective visual representation of the patient that is helpful in the patient-doctor dialogue. The patient, based on this information, can express her desire to undergo a specific treatment or make changes to the therapeutic plan. In short, the patient becomes an active agent in the choices made before the treatment. Conclusion: We believe that this algorithm will reveal itself as a useful tool in the pre-treatment decision-making process to prevent both the patient and the doctor from making a leap into the dark.

Keywords: hyaluronic acid, fillers, full face, artificial intelligence, 3D

Procedia PDF Downloads 89

Authors: Ramdani Nadia, Kheddaoui Abdelkrim, Nemmich Said, Tilmatine Amar

Abstract:

The waste production nationwide is increasing every year, on account of therapid urbanization and growing populations, also consumption modes. Algerian political authorities have chosen Technical Landfill Centres (TLC) as a competitive and safe technique of waste management. However, storing these wastes in a bad way poses several environmental challenges, especially in the Department of Saïda, the latter have significant groundwaters. The major problem registered on this Landfill is the leachate resulting from the degradation of buried wastes which were disposed off the outside of the leachate basin and present a source of pollution for the local groundwaters by heavy metals and pathogenic germs. The present paper investigates the leachate treatment ozone process produced by Dielectric Barrier Discharge (DBD) under high potential. The experimental results obtained allowed us to show the efficiency of the treatment process by ozone based on the micro pollutant analysis (DCO, DBO5 , COT, heavy metals) and microbial analysis, after ozonation treatment. The results show that 80% of micro pollutants are eliminated and 100% destruction of all bacteria which reveals the high efficiency of the process.

Keywords: landfill, leachate, treatment, ozone, polluants, bacteria, micropolluant

Procedia PDF Downloads 24

Authors: Dinesh Khanduja, Sahib Sartaj Singh

Abstract:

In India, among the start ups, many new ventures fail and for the few that survive and grow, there are always numerous problems. In order to make these surviving units productive and cost effective-in today’s competitive environment, the traditional ways of supporting small enterprises and the related programs of governmental assistance need to be significantly transformed. In this context, ‘Business Incubation’ is emerging as one of the most innovative instruments to support small enterprise creation and development all over the world. Incubators, by providing on the-spot diagnosis and treatment of business problems, dramatically lower the early stage failure rate. In Europe, US and countries like China, Singapore, Thailand etc., the exceptionally fast growth of business incubators has baffled even the researchers. In this direction in India, following on the world pattern, several initiatives have been taken over the last decade to encourage the concept of business incubation. Besides profiling the existing ‘Business Incubators’ in India, the paper dwells upon a case study of SMEs in state of Punjab for exploring the relevance of business incubation for enhancing their productive capacity.

Keywords: business incubation, Technology Business Incubator (TBI), Rural Business Hub (RBH), entrepreneurship, Business Development Services (BDS), technology management

Procedia PDF Downloads 508

Authors: Ergun Guntekin

Abstract:

Effects of heat treatment on elastic constants of Black pine (Pinus nigra) wood were investigated. Specimens were exposed to heat under atmospheric pressure at two different temperatures (180 and 210 °C) and three different time levels (2, 5, 8 hours). Three Young’s modulus in three anatomical directions, six Poisson’s ratios and three Shear modulus values associated with the main directions were evaluated by compression tests. Compression strength of the samples in three principal directions was also determined. All of the properties of the specimens tested were altered by heat treatment. The degree of alteration depends on the temperature as well as duration applied. Results indicate that EL and compression strength in L direction were not significantly influenced, compression strength in R direction significantly decreased, ER, ET and compression strength in T direction were increased for shorter periods, then dropped for 8-hour application of 180 ºC. ER was not significantly affected, compression strength in R direction and EL was significantly decreased, ET and compression strength in T direction were increased for shorter periods, then decreased for 8-hour application of 210 ºC. The shear modulus of the samples was decreased with application of treatment combinations. Most of the Poisson’s ratios were not affected by heat treatment.

Keywords: black pine, elastic constants, heat treatment, wood

Procedia PDF Downloads 155

Authors: Yasir Naseem

Abstract:

In this fast-growing and evolving world, usage and adoption of technology have displayed an essential component of the learning process, both in and out of the class, which converges and incorporates every domain of the learning aspects. It aids in learning distinct entities irrespective of their levels of challenge. It also incorporates both viewpoints of learning, i.e., competence as well as the performances of the learner. In today's learning scenario, nearly every language class ordinarily uses some form of technology. It integrates with various teaching methodologies and transforms in a way that now it grew as an integral part of the language learning courses. It has been employed to facilitate, promote, and enhances language learning. It facilitates educators in numerous ways and enhances their methodologies by equipping them to modify classroom activities, which covers every aspect of language learning.

Keywords: communication, methodology, technology, skills

Procedia PDF Downloads 177

Authors: Valentina Marutyan

Abstract:

Healthcare data mining is a rapidly developing field at the intersection of technology and medicine that has the potential to change our understanding and approach to providing healthcare. Healthcare and data mining is the process of examining huge amounts of data to extract useful information that can be applied in order to improve patient care, treatment effectiveness, and overall healthcare delivery. This field looks for patterns, trends, and correlations in a variety of healthcare datasets, such as electronic health records (EHRs), medical imaging, patient demographics, and treatment histories. To accomplish this, it uses advanced analytical approaches. Predictive analysis using historical patient data is a major area of interest in healthcare data mining. This enables doctors to get involved early to prevent problems or improve results for patients. It also assists in early disease detection and customized treatment planning for every person. Doctors can customize a patient's care by looking at their medical history, genetic profile, current and previous therapies. In this way, treatments can be more effective and have fewer negative consequences. Moreover, helping patients, it improves the efficiency of hospitals. It helps them determine the number of beds or doctors they require in regard to the number of patients they expect. In this project are used models like logistic regression, random forests, and neural networks for predicting diseases and analyzing medical images. Patients were helped by algorithms such as k-means, and connections between treatments and patient responses were identified by association rule mining. Time series techniques helped in resource management by predicting patient admissions. These methods improved healthcare decision-making and personalized treatment. Also, healthcare data mining must deal with difficulties such as bad data quality, privacy challenges, managing large and complicated datasets, ensuring the reliability of models, managing biases, limited data sharing, and regulatory compliance. Finally, secret code of data mining in healthcare helps medical professionals and hospitals make better decisions, treat patients more efficiently, and work more efficiently. It ultimately comes down to using data to improve treatment, make better choices, and simplify hospital operations for all patients.

Keywords: data mining, healthcare, big data, large amounts of data

Procedia PDF Downloads 78

Authors: A. Mohammed, A. M. Umar, S. H. Adamu

Abstract:

The study was conducted to evaluate the growth performance and nutrients utilization using 20 entire males of Sahelian goats fed Rumen content (fore-stomach digest) and poultry litter waste (PLW) at various levels of inclusion. The experimental animals were randomly allocated to diet A (Control), B (10% each of FSD and PLW), C (6.67%PLW and 13.33 FSD) and D(13.33% PLW and 6.67% FDS) at the rate of five animals per treatment. After 90 days of feeding trial, It was observed that Diets D had best feed intake and body weight gain which might be due to the good palatability of PLW and less odour of FSD in the diet. Diet C had the least feed cost then followed by diet B and while diet A(control) was more expensive than other treatments. There was the significant difference (P<0.05) between the treatments in the cost of daily feed consumption. Treatment A had the highest value while treatment C recorded the lowest cost of daily feed consumption. There was no significant difference (P > 0.05) between all treatments in terms of Cost of feed kg/ live weight gain, where treatment B had the highest value while the lowest obtained in treatment D. However, it is recommended that more research trial should be carried out to ascertain the true value of incorporating poultry litter waste and fore-stomach digest.

Keywords: poultry litter, rumen content, weight gain, economics

Procedia PDF Downloads 643

Authors: Naveen Porika, Snigdho Majumdar, Niraj Sethi

Abstract:

Water, food and energy securities are emerging as increasingly important and vital issues for India and the world. Hyderabad urban agglomeration (HUA), the capital city of Andhra Pradesh State in India, is the sixth largest city has a population of about 8.2 million. The Musi River, which is a tributary of Krishna river flows from west to east right through the heart of Hyderabad, about 80% of the water used by people is released back as sewage, which flows back into Musi every day with detrimental effects on the environment and people downstream of the city. The average daily sewage generated in Hyderabad city is 950 MLD, however, treatment capacity exists only for 541 Million Liters per Day (MLD) but only 407 MLD of sewage is treated. As a result, 543 MLD of sewage daily flows into Musi river. Hyderabad’s current estimated water demand stands at 320 Million Gallons per Day (MGD). However, its installed capacity is merely 270 MGD; by 2020 estimated demand will grow to 400 MGD. There is huge gap between current supply and demand, and this is likely to widen by 2021. Developing new fresh water sources is a challenge for Hyderabad, as the fresh water sources are few and far from the City (about 150-200 km) and requires excessive pumping. The constraints presented above make the conventional alternatives for supply augmentation unsustainable and unattractive .One such dependable and captive source of easily available water is the treated sewage. With proper treatment, water of desired quality can be recovered from the waste water (sewage) for recycle and reuse. Hyderabad Amberpet sewage treatment of capacity 339 MLD is Asia’s largest sewage treatment plant. Tertiary sewage treatment Standard basic engineering modules of 30 MLD,60 MLD, 120MLD & 180 MLD for sewage treatment plants has been developed which are utilized for developing Sewage Reclamation & Reuse model in Asia’s largest sewage treatment plant. This paper will focus on Hyderabad Water Supply & Demand, Sewage Generation & Treatment, Technical aspects of Tertiary Sewage Treatment and Utilization of developed standard modules for reclamation & reuse of treated sewage to overcome the deficit of 130 MGD as projected by 2021.

Keywords: water reclamation, reuse, Andhra Pradesh, hyderabad, musi river, sewage, demand and supply, recycle, Amberpet, 339 MLD, engineering modules, tertiary treatment

Procedia PDF Downloads 617

Authors: Khalid Abdelghany

Abstract:

Additive Manufacturing (AM) is the manufacturing technology that is used to fabricate fast products direct from CAD models in very short time and with minimum operation steps. Jointly with the advancement in medical computer modeling, AM proved to be a very efficient tool to help physicians, orthopedic surgeons and dentists design and fabricate patient-tailored surgical guides, templates and customized implants from the patient’s CT / MRI images. AM jointly with computer-assisted designing/computer-assisted manufacturing (CAD/CAM) technology have enabled medical practitioners to tailor physical models in a patient-and purpose-specific fashion and helped to design and manufacture of templates, appliances and devices with a high range of accuracy using biocompatible materials. In developing countries, there are some technical and financial limitations of implementing such advanced tools as an essential portion of medical applications. CMRDI institute in Egypt has been working in the field of Medical Additive Manufacturing since 2003 and has assisted in the recovery of hundreds of poor patients using these advanced tools. This paper focuses on the surgical and dental use of 3D printing technology in Egypt as a developing country. The presented case studies have been designed and processed using the software tools and additive manufacturing machines in CMRDI through cooperative engineering and medical works. Results showed that the implementation of the additive manufacturing tools in developed countries is successful and could be economical comparing to long treatment plans.

Keywords: additive manufacturing, dental and orthopeadic stents, patient specific surgical tools, titanium implants

Procedia PDF Downloads 315

Authors: Naomi Seidu, Edward Poluyi, Chibuikem Ikwuegbuenyi, Eghosa Morgan

Abstract:

The current poor prognosis of glioblastoma has called for the need for an improvement in treatment methods in order to improve its survival rate. Despite the different interventions currently available for this tumor, the average survival is still only a few months. (12-15). The aim is to create a more favorable prognosis and have a reduction in the resistance to treatment currently being experienced, even with surgical interventions and chemotherapy. From the available literature, there is a relationship between the presence of HOX genes (Homeobox genes) and glioblastoma, which could be attributable to the increasing treatment resistance. Hence silencing these genes can be a key to improving survival rates of glioblastoma. A series of studies have highlighted the role that HOX genes play in glioblastoma prognosis. Promotion of human glioblastoma initiation, aggressiveness, and resistance to Temozolomide has been associated with HOXA9. The role of HOX gene expression in cancer stem cells should be studied as it could provide a means of designing CSC-targeted therapies, as CSCs play a part in the initiation and progression of solid tumors.

Keywords: GBM- glioblastoma, HOXA gene- homeobox genes cluster, signaling pathways, temozolomide

Procedia PDF Downloads 106

Authors: Min Chen, Hui Lin

Abstract:

VGEs are a kind of typical web- and computer-based geographic environment, with aims of merging geographic knowledge, computer technology, virtual reality technology, network technology, and geographic information technology, to provide a digital mirror of physical geographic environments to allow users to ‘feel it in person’ by a means for augmenting the senses and to ‘know it beyond reality’ through geographic phenomena simulation and collaborative geographic experiments. Many achievements have appeared in this field, but further evolution should be explored. With the exploration of the conception of VGEs, and some examples, this article illustrated the role of VGEs and their contribution to currently GIScience. Based on the above analysis, questions are proposed for discussing about the future way of VGEs.

Keywords: virtual geographic environments (VGEs), GIScience, virtual reality, geographic information systems

Procedia PDF Downloads 575

Authors: Seval Yilmaz, Filiz Bayrakci Karel, Ali Savas Koparal

Abstract:

Textile products produced by leather have been indispensable for human consumption. Various chemicals are used to enhance the durability of end-products in the processing of leather products. The wastewaters from the leather industry which contain these chemicals exhibit toxic effects on the receiving environment and threaten the natural ecosystem. In this study, leather industry wastewater (LIW), which has high loads of contaminants, was treated using advanced treatment techniques instead of conventional methods. During the experiments, the performance of electrochemical methods was investigated. During the electrochemical experiments, the performance of batch electrooxidation (EO) using boron-doped diamond (BDD) electrodes with monopolar configuration for removal of chemical oxygen demand (COD) from LIW were investigated. The influences of electrolysis time, current density (which varies as 5 mA/cm², 10 mA/cm², 20 mA/cm², 30 mA/cm², 50 mA/cm²) and initial pH (which varies as 3,80 (natural pH of LIW), 7, 9) on removal efficiency were investigated in a batch stirred cell to determine the best treatment conditions. The current density applied to the electrochemical reactors is directly proportional to the consumption of electric energy, so electrical energy consumption was monitored during the experiment. The best experimental conditions obtained in electrochemical studies were as follows: electrolysis time = 60 min, current density = 30.0 mA/cm², pH 7. Using these parameters, 53.59% COD removal rates for LIW was achieved and total energy consumption was obtained as 13.03 kWh/m³. It is concluded that electrooxidation process constitutes a plausible and developable method for the treatment of LIW.

Keywords: BDD electrodes, COD removal, electrochemical treatment, leather industry wastewater

Procedia PDF Downloads 162

Authors: Nikolett Deutsch, Éva Pintér, Péter Bagó, Miklós Hetényi

Abstract:

Strategic technology management has emerged and evolved parallelly with strategic management paradigms. It focuses on the opportunity for organizations operating mainly in technology-intensive industries to explore and exploit technological capabilities upon which competitive advantage can be obtained. As strategic technology management involves multifunction within an organization, requires broad and diversified knowledge, and must be developed and implemented with business objectives to enable a firm’s profitability and growth, excellence in strategic technology management provides unique opportunities for organizations in terms of building a successful future. Accordingly, a framework supporting the evaluation of the technological readiness level of management can significantly contribute to developing organizational competitiveness through a better understanding of strategic-level capabilities and deficiencies in operations. In the last decade, several innovation maturity assessment models have appeared and become designated management tools that can serve as references for future practical approaches expected to be used by corporate leaders, strategists, and technology managers to understand and manage technological capabilities and capacities. The aim of this paper is to provide a comprehensive review of the state-of-the-art innovation maturity frameworks, to investigate the critical lessons learned from their application, to identify the similarities and differences among the models, and identify the main aspects and elements valid for the field and critical functions of technology management. To this end, a systematic literature review was carried out considering the relevant papers and articles published in highly ranked international journals around the 27 most widely known innovation maturity models from four relevant digital sources. Key findings suggest that despite the diversity of the given models, there is still room for improvement regarding the common understanding of innovation typologies, the full coverage of innovation capabilities, and the generalist approach to the validation and practical applicability of the structure and content of the models. Furthermore, the paper proposes an initial structure by considering the maturity assessment of the technological capacities and capabilities - i.e., technology identification, technology selection, technology acquisition, technology exploitation, and technology protection - covered by strategic technology management.

Keywords: innovation capabilities, innovation maturity models, technology audit, technology management, technology management maturity models

Procedia PDF Downloads 62

Authors: Maha Ibrahim Mohamed Khalifa

Abstract:

Background: Dental fear and anxiety lead to avoidance of dental treatment and deterioration of oral health. Aim of the study: To assess the levels of fear and anxiety among school-age children undergoing dental treatment. Setting: The study was conducted in Outpatient Dental Clinics at Benha Teaching Hospital. Research design: A descriptive research design was utilized to conduct the study. Sample: A purposive sample of 60 school-age children and their mothers attending at the previously mentioned setting was included. Tools: Three tools were used: Tool one: A structured interviewing questionnaire for Personal characteristics of children and their mothers. Tool two: Dental Subscale of Children's Fear Survey Schedule (CFSS-DS). Tool three: Modified Dental Anxiety Scale (MDAS). Results: It was illustrated that more than two-fifths (43.3%) of children had maximum fear and more than half of children (53.3%) had maximal anxiety. Conclusion: Many school-age children undergoing dental treatment suffer from high levels of fear and anxiety. Recommendations: The study recommended further research should be conducted to assess levels of fear and anxiety among children undergoing dental treatments and preferable nursing interventions for reducing their fears and anxieties.

Keywords: fear, anxiety, children, dental treatment

Procedia PDF Downloads 89

Authors: Folajinmi Oluwasina, Greg Abiaziem, Moses Luke, Mobolaji Kolawole, Nancy Yibowei, Anne Taiwo

Abstract:

Background: Occurrence of HIV infection has an adverse effect on the natural causes of Hepatitis B Viral (HBV) infection, faster progression of hepatic fibrosis demonstrated in patients with co-infection. This study was carried out to determine the incidence of HBV infection among HIV-positive patients, and to retrospectively evaluate laboratory characteristics of patients with HIV/HBV co-infection. Methods: A retrospective analysis of patient files for all HIV-infected cases followed-up and treated at 52 health facilities. Among HIV-infected cases, those with HBsAg positivity and HIV/Hepatitis B co-infection were determined. Socio demographic, alcohol or substance use, ART, CD4, Viral Load levels and treatment durations were retrospectively evaluated. Results: Of the 125 HIV-infected patients evaluated retrospectively, 17 (13.6%) had HBsAg positivity. Of these 17 cases were 11(64.7%) male and 6 (35.3%) female, with a mean age of 48.7 years. No patients had a history of alcohol or substance use. The mean duration of follow up was 28 months. 9 (52.9%) patients had negative HBV DNA at presentation while 8(47%) had positive HBV DNA, with normal ALT levels in all subjects. Among the 9 cases with negative HBV DNA who had no indication for the treatment of chronic hepatitis B. In five cases, treatment was commenced since HBV DNA was elevated in conjunction with low CD4. One patient in whom treatment was not indicated based on HBV DNA and CD4 levels in conjunction with the absence of AIDS defining clinical picture was currently being followed-up without treatment. Of the patients receiving HAART therapy, the average CD4 count at presentation was 278 cells/mm3 vs. 466 cells/mm3 at the end of 12 months. In three subjects with positive HBV DNA, a decrease in HBV DNA was noted after initiation of treatment. In four patients with negative DNA who received treatment, the HBV DNA negative status was found to remain, while one patient who did not receive treatment had elevated HBV DNA and decreased CD4 levels. Conclusion: It was shown that this group of patients with HIV/HBV co-infection, HAART was found to be associated with a decrease in HBV DNA in HBV DNA positive cases, absence of transition to positivity among those with negative HBV DNA, and with increased CD4 in all subjects.

Keywords: Hepatitis B, DNA, anti retroviral therapy, co-infection

Procedia PDF Downloads 270

Authors: Muhammad Zeeshan, Rabia Nazir, Lubna Tahir

Abstract:

Low cost filter based on iron doped zeolite (Fe-Z) and pottery clay was developed for an effective and efficient treatment of the drinking water contaminated with microbes. Fe-Z was characterized using powder XRD, SEM and EDX and shown to have average particle size of 49 nm with spongy appearance. The simulated samples of water self-contaminated with six microbes (S. typhi, B. subtilus, E. coli, S. aures, K. pneumoniae, and P. aeruginosa) after treatment with Fe-Z indicated effective removal of all the microbes in less than 30 min. Equally good results were obtained when actual drinking water samples, totally unfit for human consumption, were treated with Fe-Z.

Keywords: iron doped zeolite, biological and chemical treatment, drinking water

Procedia PDF Downloads 448

Authors: Micheal O. Alabi

Abstract:

Additive manufacturing (AM) is the official industry standard term (ASTM F2792) for all applications of the technology which is also known as 3D printing technology. It is defined as the process of joining materials to make objects from 3D model data, and it is usually layer upon layer, as opposed to subtractive manufacturing methodologies. This technology has gained significant interest within the academic, research institute and industry because of its ability to create complex geometries with customizable material properties. Despite the late adoption of the technology, additive manufacturing has been active in South Africa for past 21 years and it is predicted that additive manufacturing technology will play a significant and game-changing role in the fourth industrial revolution and in particular it promises to play an ever-growing role in efforts to re-industrialize the economy of South Africa. At the end of 2006, there are approximately ninety 3D printers in South Africa and in 2015 it was estimated that there are 3500 additive manufacturing systems and 3D printers in circulation in South Africa. A reasonable number of these additive manufacturing machines are in the high end of the market, in science councils and higher education institutions and this shows that the future of additive manufacturing in South Africa is very brighter compared to other African countries. This paper reviews the past and current industrial applications of additive manufacturing in South Africa from the academic research and industry perspective and what are the benefits of this technology to manufacturing companies and industrial sectors in the country.

Keywords: additive manufacturing, 3D printing technology, industrial applications, manufacturing

Procedia PDF Downloads 473

Authors: Omar Al Denali, Abdelaziz Badi

Abstract:

The ASTM A516 Grade 70 steel is a suitable material used for the fabrication of boiler pressure vessels working in moderate and lower temperature services, and it has good weldability and excellent notch toughness. The post-weld heat treatment (PWHT) or stress-relieving heat treatment has significant effects on avoiding the martensite transformation and resulting in high hardness, which can lead to cracking in the heat-affected zone (HAZ). An adaptive neuro-fuzzy inference system (ANFIS) was implemented to predict the material tensile strength of post-weld heat treatment (PWHT) experiments. The ANFIS models presented excellent predictions, and the comparison was carried out based on the mean absolute percentage error between the predicted values and the experimental values. The ANFIS model gave a Mean Absolute Percentage Error of 0.556 %, which confirms the high accuracy of the model.

Keywords: prediction, post-weld heat treatment, adaptive neuro-fuzzy inference system, mean absolute percentage error

Procedia PDF Downloads 155

Authors: Lizbeth Puerta, Enselmina Marín

Abstract:

The purpose of this research is to present a survey to be applied to professors of public universities, to identify the factors that benefit or hinder the university-industry relation. Hence, this research studies some elements that integrate the variables: Knowledge management, technology management, and technology transfer; to define the existence of a relation between these variables and the industry necessities of innovation. This study is exploratory, descriptive and non-experimental. The research question is: What is the impact of the knowledge management, the technology management, and the technology transfer, made by administrative support areas of the public universities, in the industries innovation? Thus, literature review was made to identify some elements that should be considered to design a survey that allows to obtain valid information to the study variables. After this, the survey was developed, and the Content Validity Analysis was made through the Lawshe Model. The analysis indicated that the Content Validity Index (CVI) was 0.80. Hence, it was determined that this survey presents acceptable psychometric properties to be used as an evaluation tool.

Keywords: innovation, knowledge management, technology management, technology transfer

Procedia PDF Downloads 408

Authors: Daniele Zullino, Gabriel Thorens, Léonice Furtado, Federico Seragnoli, Radu Iuga, Louise Penzenstadler

Abstract:

Context: Since the start of the 21st century, there has been a resurgence of interest in psychedelics, marked by a renewed focus on scientific investigations into their therapeutic potential. While psychedelic therapy has gained recognition for effectively treating depression and anxiety disorders, notable progress has been made in the clinical development of substances like psilocybin. Moreover, mounting evidence suggests promising applications of Lysergic acid diethylamide (LSD) and psilocybin in the field of addiction medicine. In Switzerland, compassionate treatment with LSD and psilocybin has been permitted since 2014 through exceptional licenses granted by the Federal Office of Public Health. This treatment approach is also available within the Geneva treatment program, extending its accessibility to patients undergoing opioid-assisted treatment involving substances like morphine and diacetylmorphine. The aim of this study is to assess the feasibility of psychedelic-assisted therapy in patients with opioid use disorder who are undergoing opioid-assisted treatment. This study addresses the question of whether psychedelic-assisted therapy can be successfully implemented in patients with opioid use disorder. It also explores the effects of psychedelic therapy on the patient's experiences and outcomes. Methodology: This is an open case series on six patients who have undergone at least one session with either LSD (100-200 micrograms) or psilocybin (20-40 mg). The patients were assessed using the Five Dimensional Altered States of Consciousness (5D-ASC)-Scale. The data were analyzed descriptively to identify patterns and trends in the patients' experiences. Results: The patients experienced substantial positive psychedelic effects during the psychedelic sessions without significant adverse effects. The patients reported positive experiences and improvements in their condition. Conclusion: The findings of this study support the feasibility and potential efficacy of psychedelic-assisted therapy in patients undergoing opioid-assisted treatment.

Keywords: psychedelics, psychedelic-assisted treatment, opioid use disorder, addiction, LSD, psilocybin

Procedia PDF Downloads 56

Authors: Amin Abbasi, Fariborz Shekari, Seyed Bahman Mousavi

Abstract:

Seed aging during storage is a complex biochemical and physiological processes that can lead to reduce seed germination. This phenomenon associated with increasing of total antioxidant activity during aging. To study the effects of hormones on seed aging, aged wheat seeds (control, 90 and 80% viabilities) were treated with GA3, Salicylic Acid, and paclobutrazol and antioxidant system were investigated as molecular biomarkers for seed vigor. The results showed that, seed priming treatment significantly affected germination percentage, normality seedling percentage, H2O2, MDA, CAT, APX, and GPX activates. Maximum germination percentage achieve in GA3 priming in control treatment. Germination percentage and normal seedling percentage increased in other GA3 priming treatment compared with other hormones. Also aging increased MDA, H2O2 content. MDA is considered sensitive marker commonly used for assessing membrane lipid peroxidation and H2O2result in toxicity to cellular membrane system and damages to plant cells. Amount of H2O2 and MDA declined in GA3 treatment. CAT, GPX and APX activities were reduced by increasing the aging time and at different levels of priming. The highest APX activity was observed in Salicylic Acid control treatment and the highest GPX and CAT activity was obtained in GA3 control treatment. The lowest MDA and H2O2 showed in GA3 control treatment, too. Hormone priming increased Antioxidant enzyme activity and decreased amount of reactive oxygen space and malondialdehyde (MDA) under aging treatment. Also, GA3 priming treatments have a significant effect on germination percentage and number of normal seedling. Generally aging seed, increase ROS and lipid peroxidation. Antioxidant enzymes activity of aged seeds increased after hormone priming.

Keywords: hormones priming, wheat, aging seed, antioxidant, lipid peroxidation

Procedia PDF Downloads 498

Authors: Rian Diana, Naufal Muharam Nurdin, Faisal Anwar, Hadi Riyadi, Ali Khomsan

Abstract:

The use of traditional medicine (herbs and medicinal plants) are common among Indonesian people especially the elderly. Few study explore the use of medicinal plants in middle aged people. This study aims to collect information on the use of medicinal plants in middle aged people in rural areas. This cross sectional study included 224 subjects aged 45-59 years old and conducted in Cianjur District, West Java in 2014. Semi-structured questionnaires were used to collect information about preference in treatment of illness, the use of medicinal plants, and their purposes. Information also recorded plant names, parts used, mode of preparation, and dosage. Buying drugs in stall (83.9%) is the first preference in treatment of illness, followed by modern treatment 19.2% (doctors) and traditional treatment 17.0% (herbs/medicinal plants). 87 subjects (38.8%) were using herbs and medicinal plants for curative (66.7%), preventive (31.2%), and rehabilitative (2.1%) purposes. In this study, 48 species are used by the subjects. Physalis minima L. 'cecenet', Orthosiphon aristatus Mic. 'kumis kucing', and Annona muricata 'sirsak' are commonly used for the treatment of hypertension and stiffness. Leaves (64.6%) are the most common part used. Medicinal plants were washed and boiled in a hot water. Subject drinks the herbs with a different dosage. One in three middle aged people used herbal and medicinal plants for curative and preventive treatment particularly hypertension and stiffness. Increasing knowledge about herbal or medicinal plants dosage and their interaction with medical drugs are important to do.Doses vary between 1-3 glasses/day for treatment and 1-2 glasses/months for prevention of diseases.

Keywords: herbs, hypertension, medicinal plants, middle age, rural

Procedia PDF Downloads 244

Authors: Faizul Azly Abd Dzubir, Muhammad F. Othman

Abstract:

Conventional structural health monitoring approach for mechanical equipment uses inspection data from Non-Destructive Testing (NDT) during plant shut down window and fitness for service evaluation to estimate the integrity of the equipment that is prone to crack damage. Yet, this forecast is fraught with uncertainty because it is often based on assumptions of future operational parameters, and the prediction is not continuous or online. Advanced Diagnostic and Prognostic Technology (ADaPT) uses Acoustic Emission (AE) technology and a stochastic prognostic model to provide real-time monitoring and prediction of mechanical defects or cracks. The forecast can help the plant authority handle their cracked equipment before it ruptures, causing an unscheduled shutdown of the facility. The ADaPT employs process historical data trending, finite element analysis, fitness for service, and probabilistic statistical analysis to develop a prediction model for crack initiation and growth due to mechanical damage. The prediction model is combined with live equipment operating data for real-time prediction of the remaining life span owing to fracture. ADaPT was devised at a hot combined feed exchanger (HCFE) that had suffered creep crack damage. The ADaPT tool predicts the initiation of a crack at the top weldment area by April 2019. During the shutdown window in April 2019, a crack was discovered and repaired. Furthermore, ADaPT successfully advised the plant owner to run at full capacity and improve output by up to 7% by April 2019. ADaPT was also used on a coke drum that had extensive fatigue cracking. The initial cracks are declared safe with ADaPT, with remaining crack lifetimes extended another five (5) months, just in time for another planned facility downtime to execute repair. The prediction model, when combined with plant information data, allows plant operators to continuously monitor crack propagation caused by mechanical damage for improved maintenance planning and to avoid costly shutdowns to repair immediately.

Keywords: mechanical damage, cracks, continuous monitoring tool, remaining life, acoustic emission, prognostic model

Procedia PDF Downloads 77

Authors: Sandrine Delpeux-Ouldriane, Min Cai, Laurent Duclaux, Laurence Reinert, Fabrice Muller

Abstract:

A novel hybrid adsorbent, based on chitosan biopolymer, clays and activated carbon was prepared. Hybrid chitosan beads containing dispersed clays and activated carbons were prepared by precipitation in basic medium. Such a composite material is still very porous and presents a wide adsorption spectrum. The obtained composite adsorbent is able to handle all the pollution types including heavy metals, polar and hydrophobic organic molecules and nitrates. It could find a place of choice in tertiary water treatment processes or for an ‘at source’ treatment concerning chemical or pharmaceutical industries.

Keywords: adsorption, chitosan, clay mineral, activated carbon

Procedia PDF Downloads 404

Authors: Petros Gkotsis, Anastasios Zouboulis, Manasis Mitrakas, Dimitrios Zamboulis, E. Peleka

Abstract:

The most serious drawback in wastewater treatment using membrane bioreactors (MBRs) is membrane fouling which gradually leads to membrane permeability decrease and efficiency deterioration. This work is part of a research project that aims to develop an integrated methodology for membrane fouling control, using specific chemicals which will enhance the coagulation and flocculation of compounds responsible for fouling, hence reducing biofilm formation on the membrane surface and limiting the fouling rate acting as a pre-treatment step. For this purpose, a pilot-scale plant with fully automatic operation achieved by means of programmable logic controller (PLC) has been constructed and tested. The experimental set-up consists of four units: wastewater feed unit, bioreactor, membrane (side-stream) filtration unit and permeate collection unit. Synthetic wastewater was fed as the substrate for the activated sludge. The dissolved oxygen (DO) concentration of the aerobic tank was maintained in the range of 2-3 mg/L during the entire operation by using an aerator below the membrane module. The membranes were operated at a flux of 18 LMH while membrane relaxation steps of 1 min were performed every 10 min. Both commercial and composite coagulants are added in different concentrations in the pilot-scale plant and their effect on the overall performance of the ΜΒR system is presented. Membrane fouling was assessed in terms of TMP, membrane permeability, sludge filterability tests, total resistance and the unified modified fouling index (UMFI). Preliminary tests showed that particular attention should be paid to the addition of the coagulant solution, indicating that pipe flocculation effectively increases hydraulic retention time and leads to voluminous sludge flocs. The most serious drawback in wastewater treatment using MBRs is membrane fouling, which gradually leads to membrane permeability decrease and efficiency deterioration. This results in increased treatment cost, due to high energy consumption and the need for frequent membrane cleaning and replacement. Due to the widespread application of MBR technology over the past few years, it becomes clear that the development of a methodology to mitigate membrane fouling is of paramount importance. The present work aims to develop an integrated technique for membrane fouling control in MBR systems and, thus, contribute to sustainable wastewater treatment.

Keywords: coagulation, membrane bioreactor, membrane fouling, pilot plant

Procedia PDF Downloads 310