Search results for: software process engineering

Authors: Christian Doppler, Gernot Hirschl, Gerhard Zsiga

Abstract:

Starting from 2020, an EU-wide CO2-limitation of 95g/km is scheduled for the average of an OEMs passenger car fleet. Considering that, further measures of optimization on the diesel cycle will be necessary in order to reduce fuel consumption and emissions while keeping performance values adequate at the least. The present article deals with charge air cooling (CAC) on the basis of a diesel passenger car model in a 0D/1D-working process calculation environment. The considered engine is a 2.4 litre EURO VI diesel engine with variable geometry turbocharger (VGT) and low-pressure exhaust gas recirculation (LP EGR). The object of study was the impact of charge air cooling on the engine working process at constant boundary conditions which could have been conducted with an available and validated engine model in AVL BOOST. Part load was realized with constant power and NOx-emissions, whereas full load was accomplished with a lambda control in order to obtain maximum engine performance. The informative results were used to implement a simulation model in Matlab/Simulink which is further integrated into a full vehicle simulation environment via coupling with ICOS (Independent Co-Simulation Platform). Next, the dynamic engine behavior was validated and modified with load steps taken from the engine test bed. Due to the modular setup in the Co-Simulation, different CAC-models have been simulated quickly with their different influences on the working process. In doing so, a new cooler variation isn’t needed to be reproduced and implemented into the primary simulation model environment, but is implemented quickly and easily as an independent component into the simulation entity. By means of the association of the engine model, longitudinal dynamics vehicle model and different CAC models (air/air & water/air variants) in both steady state and transient operational modes, statements are gained regarding fuel consumption, NOx-emissions and power behavior. The fact that there is no more need of a complex engine model is very advantageous for the overall simulation volume. Beside of the simulation with the mentioned demonstrator engine, there have also been conducted several experimental investigations on the engine test bench. Here the comparison of a standard CAC with an intake-manifold-integrated CAC was executed in particular. Simulative as well as experimental tests showed benefits for the water/air CAC variant (on test bed especially the intake manifold integrated variant). The benefits are illustrated by a reduced pressure loss and a gain in air efficiency and CAC efficiency, those who all lead to minimized emission and fuel consumption for stationary and transient operation.

Keywords: air/water-charge air cooler, co-simulation, diesel working process, EURO VI fuel consumption

Procedia PDF Downloads 256

Authors: T. Boonkang, C. Santhaweesuk, N. Pianthong, P. Neeramon, A. Phimhlo, S. Bangphan

Abstract:

The objective of this research was to apply metakaolin from northeast of Thailand as a binder in the casting process of rice polishing cylinder in replacement of the imported calcined magnesite cement and to reduce the production cost of the cylinder. Metakaolin was obtained from three different regions (Udon Thani, Nakhon Phanom, and Ubon Ratchathani). The design of experiment analysis using the MINITAB Release 14 based on the compressive strength and tensile strength testing was conducted. According to the analysis results, it was found that the optimal proportions were calcined magnesite cement: metakaolin from Udon Thani, Nakhon Phanom and Ubon Ratchathani equal to 63:37, 71:29, and 100:0, respectively. When used this formula to cast the cylinder and test the rice milling, it was found that the average broken rice percent was 32.52 and 38.29 for the cylinder contained the metakaolin from Udon Thani and Nakhon Phanom, respectively, which implied that the cylinder which contained the metakaolin from Udon Thani has higher efficiency than the cylinder which contained the metakaolin from Nakhon Phanom at 0.05 level of statistical significance. Whereas, the average wear rate of cylinder from both resources were 7.27 and 6.53 g/h, respectively.

Keywords: binder, casting, metakaolin, rice polishing cylinder

Procedia PDF Downloads 295

Authors: Kassahun Tilahun Dessie

Abstract:

The purpose of this study was to explore the awareness of teachers and the attitude they have to the curriculum they implement as well as to assess the actual and desired magnitude of teachers' participation in curriculum development process. It also aimed at investigating the factors that affect teachers' level of conception and perception towards the new higher education curriculum. The study was carried out in Debre Birhan University. Teachers, course coordinators, team leaders and presidents were included in the study as research subjects. Teachers were proportionally selected from each department (of the six faculties) based on available sampling technique. Accordingly, a total of 103 teachers were chosen as a subject of the study. In order to collect first hand data from the teachers, a questionnaire with four parts was developed by the researcher. To this end, scales were designed for measuring the extent of teachers' awareness and attitude. Each of the scales encompasses 11 and 17 items respectively. An open ended questionnaire was also attached for the purpose of obtaining elaborated data on the issue. Information was also obtained from interviews with presidents, team leaders and course coordinators. The data obtained were analyzed qualitatively using descriptive statistical tools. The overall results of the analysis revealed that the awareness of teachers on the curriculum was low. The meager participation of teachers in the process of curriculum development and the deficiency of trainings on the concern were major factors. Teachers' perception towards the existence and implementation of the new curriculum was also inclined to the negative, though difficult to generalize. Lack of awareness, administrators poor approach and lack of facilitating appropriate incentives as well as absence of room for evaluating the curriculum etc plays big role in endangering teachers attitude while the up to datedness of the new curriculum, involvement of teachers in the curriculum development process, the wide ranging quality of the new curriculum etc laid a better ground to boost teachers attitude towards the curriculum. This may have implication to the university in that there is a need to facilitate workshops or awareness creation trainings, to have positive and cooperative administrators, and embracing committed teachers to implement the curriculum efficiently.

Keywords: conception, perception, curriculum, higher education, Ethiopia

Procedia PDF Downloads 488

Authors: Stephen Bahooshy

Abstract:

Co-producing services with the people that access them is considered best practice in the United Kingdom, with the Care Act 2014 arguing that people who access services and their carers should be involved in the design, commissioning and delivery of services. Co-production is a way of working with the community, breaking down barriers of access and providing meaningful opportunity for people to engage. Unfortunately, owing to a number of reported factors such as time constraints, practitioner experience and departmental budget restraints, this process is not always followed. In 2019, in a south London borough, d/Deaf people who access services were engaged in the design, commissioning and delivery of an information and advice service that would support their community to access local government services. To do this, sensory impairment social workers and commissioners collaborated to host a series of engagement events with the d/Deaf community. Interpreters were used to enable communication between the commissioners and d/Deaf participants. Initially, the community’s opinions, ideas and requirements were noted. This was then summarized and fed back to the community to ensure accuracy. Subsequently, a service specification was developed which included performance metrics, inclusive of qualitative and quantitative indicators, such as ‘I statements’, whereby participants respond on an adapted Likert scale how much they agree or disagree with a particular statement in relation to their experience of the service. The service specification was reviewed by a smaller group of d/Deaf residents and social workers, to ensure that it met the community’s requirements. The service was then tendered using the local authority’s e-tender process. Bids were evaluated and scored in two parts; part one was by commissioners and social workers and part two was a presentation by prospective providers to an evaluation panel formed of four d/Deaf residents. The internal evaluation panel formed 75% of the overall score, whilst the d/Deaf resident evaluation panel formed 25% of the overall tender score. Co-producing the evaluation panel with social workers and the d/Deaf community meant that commissioners were able to meet the requirements of this community by developing evaluation questions and tools that were easily understood and use by this community. For example, the wording of questions were reviewed and the scoring mechanism consisted of three faces to reflect the d/Deaf residents’ scores instead of traditional numbering. These faces were a happy face, a neutral face and a sad face. By making simple changes to the commissioning and tender evaluation process, d/Deaf people were able to have meaningful involvement in the design and commissioning process for a service that would benefit their community. Co-produced performance metrics means that it is incumbent on the successful provider to continue to engage with people accessing the service and ensure that the feedback is utilized. d/Deaf residents were grateful to have been involved in this process as this was not an opportunity that they had previously been afforded. In recognition of their time, each d/Deaf resident evaluator received a £40 gift voucher, bringing the total cost of this co-production to £160.

Keywords: co-production, community engagement, deaf and hearing impaired, service design

Procedia PDF Downloads 259

Authors: Kholod Hajo

Abstract:

In this study COMSOL Multiphysics was used to design lateral flow biosensors (LFBs) which provide advantages in low cost, simplicity, rapidity, stability and portability thus making LFBs popular in biomedical, agriculture, food and environmental sciences. This study was focused on simulation model of biosensor based on gold nanoparticles (GNPs) designed using software package (COMSOL Multiphysics), the magnitude of the laminar velocity field in the flow cell, concentration distribution in the analyte stream and surface coverage of adsorbed species and average fractional surface coverage of adsorbed analyte were discussed from the model and couples of suggestion was given in order to functionalize GNPs and to increase the accuracy of the biosensor design, all above were obtained acceptable results.

Keywords: model, gold nanoparticles, biosensor, COMSOL Multiphysics

Procedia PDF Downloads 241

Authors: A. M. Sagir

Abstract:

The aim of this paper is to investigate the performance of the developed linear multistep block method for solving first order initial value problem of Ordinary Differential Equations (ODEs). The method calculates the numerical solution at three points simultaneously and produces three new equally spaced solution values within a block. The continuous formulations enable us to differentiate and evaluate at some selected points to obtain three discrete schemes, which were used in block form for parallel or sequential solutions of the problems. A stability analysis and efficiency of the block method are tested on ordinary differential equations involving practical applications, and the results obtained compared favorably with the exact solution. Furthermore, comparison of error analysis has been developed with the help of computer software.

Keywords: block method, first order ordinary differential equations, linear multistep, self-starting

Procedia PDF Downloads 294

Authors: Matheus Müller, Delma Vidal

Abstract:

The present paper aims to expose two techniques of dewatering for sludge, analyzing its operations and dewatering processes, aiming at improving the conditions of disposal of residues with high liquid content. It describes the field tests performed on two geotextile systems, a closed geotextile tube and an open geotextile drying bed, both of which are submitted to two filling cycles. The sludge used in the filling cycles for the field trials is from the water treatment plant of the Technological Center of Aeronautics – CTA, in São José dos Campos, Brazil. Data about volume and height abatement due to the dewatering and consolidation were collected per time, until it was observed constancy. With the laboratory analysis of the sludge allied to the data collected in the field, it was possible to perform a critical comparative study between the observed and the scientific literature, in this way, this paper expresses the data obtained and compares them with the bibliography. The tests were carried out on three fronts: field tests, including the filling cycles of the systems with the sludge from CTA, taking measurements of filling time per cycle and maximum filling height per cycle, heights against the abatement by dewatering of the systems over time; tests carried out in the laboratory, including the characterization of the sludge and removal of material samples from the systems to ascertain the solids content within the systems per time and; comparing the data obtained in the field and laboratory tests with the scientific literature. Through the study, it was possible to perceive that the process of densification of the material inside a closed system, such as the geotextile tube, occurs faster than the observed in the drying bed system. This process of accelerated densification can be brought about by the pumping pressure of the sludge in its filling and by the confinement of the residue through the permeable geotextile membrane (allowing water to pass through), accelerating the process of densification and dewatering by its own weight after the filling with sludge.

Keywords: consolidation, dewatering, geotextile drying bed, geotextile tube

Procedia PDF Downloads 114

Authors: Berhanu Keno Terfa

Abstract:

Flash floods are among the most dangerous natural disasters that pose a significant threat to human existence. They occur frequently and can cause extensive damage to homes, infrastructure, and ecosystems while also claiming lives. Although flash floods can happen anywhere in the world, their impact is particularly severe in developing countries due to limited financial resources, inadequate drainage systems, substandard housing options, lack of early warning systems, and insufficient preparedness. To address these challenges, a comprehensive study has been undertaken to analyze and map flood inundation using Geographic Information System (GIS) techniques by considering various factors that contribute to flash flood resilience and developing effective mitigation strategies. Key factors considered in the analysis include slope, drainage density, elevation, Curve Number, rainfall patterns, land-use/cover classes, and soil data. These variables were computed using ArcGIS software platforms, and data from the Sentinel-2 satellite image (with a 10-meter resolution) were utilized for land-use/cover classification. Additionally, slope, elevation, and drainage density data were generated from the 12.5-meter resolution of the ALOS Palsar DEM, while other relevant data were obtained from the Ethiopian Meteorological Institute. By integrating and regularizing the collected data through GIS and employing the analytic hierarchy process (AHP) technique, the study successfully delineated flash flood hazard zones (FFHs) and generated a suitable land map for urban agriculture. The FFH model identified four levels of risk in Bishoftu City: very high (2106.4 ha), high (10464.4 ha), moderate (1444.44 ha), and low (0.52 ha), accounting for 15.02%, 74.7%, 10.1%, and 0.004% of the total area, respectively. The results underscore the vulnerability of many residential areas in Bishoftu City, particularly the central areas that have been previously developed. Accurate spatial representation of flood-prone areas and potential agricultural zones is crucial for designing effective flood mitigation and agricultural production plans. The findings of this study emphasize the importance of flood risk mapping in raising public awareness, demonstrating vulnerability, strengthening financial resilience, protecting the environment, and informing policy decisions. Given the susceptibility of Bishoftu City to flash floods, it is recommended that the municipality prioritize urban agriculture adaptation, proper settlement planning, and drainage network design.

Keywords: remote sensing, flush flood hazards, Bishoftu, GIS.

Procedia PDF Downloads 17

Authors: Ahmed Amin Mousa, M. Abd El Salam

Abstract:

The current study presents a proposed program for acquisition the skills and techniques needed to produce concept cartoon. The proposed program has been prepared for non-specialist students who have never used neither graphics nor animating software. It was presented to postgraduates in Faculty of Education for Early Childhood, Cairo University, during the spring term of the 2014-2015 academic year. The program works in three different aspects: Drawing and images editing, sound manipulation, and creating animation. In addition, the researchers have prepared a questionnaire for measuring the quality of the concept cartoons produced by the students. The questionnaire was used as a pre-test and post-test, and at the end of the study, a significant difference was determined in favour of post-test results.

Keywords: cartoon, concept cartoon, kindergarten, animation

Procedia PDF Downloads 418

Authors: Olga V. Korotkaya

Abstract:

This article is devoted to an important problem of calculation of deflected mode of the combustion chamber and the nozzle end of a new liquid-propellant rocket cruise engine. A special attention is given to the methodology of calculation. Three operating modes are considered. The analysis has been conducted in ANSYS software. The methods of conducted research are mathematical modelling, substructure method, cyclic symmetry, and finite element method. The calculation has been carried out to order of S. P. Korolev Rocket and Space Corporation «Energia». The main results are practical. Proposed methodology and created models would be able to use for a wide range of strength problems.

Keywords: combustion chamber, cyclic symmetry, finite element method, liquid-propellant rocket engine, nozzle end, substructure

Procedia PDF Downloads 489

Authors: Nan Stevens

Abstract:

Photo-voice is a participatory method through which participants identify and represent their lived experiences and contexts through the use of photo imagery. Photo-voice is a qualitative research method that explores individuals’ lived experiences. This method is known as a creative art form to help researchers listen to the 'voice' of a certain population. A teacher educator at Thompson Rivers University, responsible for preparing new teachers for the demands of the profession in an ever-changing demographic, utilized the Photo-voice method to enable a self-study of emerging teachers’ readiness for the inclusive classroom. Coding analysis was applied to 96 Photo-voice portfolios, which were created over two years with the Inclusive Education course work, in a Bachelor of Education program (Elementary). Coding utilized students’ written associations to their visual images, anecdotes attached to visual metaphors, and personal narratives that illustrated the professional development process in which they were engaged. Thematic findings include: 1) becoming an inclusive educator is a process; 2) one must be open to identifying and exploring their fear and biases, and 3) an attitudinal shift enables relevant skill acquisition and readiness for working with diverse student needs.

Keywords: teacher education, inclusive education, professional development, Photo-voice

Procedia PDF Downloads 124

Authors: Imoh Philip

Abstract:

Basà language is classified as belonging to Kainji family, under the sub-phylum Western-Kainji known as Rubasa (Basa Benue) (Croizier & Blench, 1992:32). Basà is an under-described language spoken in the North-Central Nigeria. The language is characterized by subject-verb-object (henceforth SVO) as its canonical word order. Data for this work is sourced from the researcher’s native intuition of the language corroborated with a careful observation of native speakers. This paper investigates the syntactic derivational strategy of information-structure encoding in Basà language. It emphasizes on a negative operator, as a strategy for focusing a constituent or clause that follows it and negativizes a whole proposition. For items that are not nouns, they have to undergo an obligatory nominalization process, either by affixation, modification or conversion before they are moved to the pre verbal position for these operations. The study discovers and provides evidence of the fact showing that deferent constituents in the sentence such as the subject, direct, indirect object, genitive, verb phrase, prepositional phrase, clause and idiophone, etc. can be focused with the same negativizing operator. The process is characterized by focusing the pre verbal NP constituent alone, whereas the whole proposition is negated. The study can stimulate similar study or be replicated in other languages.

Keywords: negation, focus, Basà, nominalization

Procedia PDF Downloads 586

Authors: Miguel Contreras, David Long, Will Bachman

Abstract:

Background: Microscopy plays a central role in cell and developmental biology. In particular, fluorescence microscopy can be used to visualize specific cellular components and subsequently quantify their morphology through development of virtual-cell models for study of effects of mechanical forces on cells. However, there are challenges with these imaging experiments, which can make it difficult to quantify cell morphology: inconsistent results, time-consuming and potentially costly protocols, and limitation on number of labels due to spectral overlap. To address these challenges, the objective of this project is to develop an automatic computational machine learning pipeline to predict cellular components morphology for virtual-cell generation based on fluorescence cell membrane confocal z-stacks. Methods: Registered confocal z-stacks of nuclei and cell membrane of endothelial cells, consisting of 20 images each, were obtained from fluorescence confocal microscopy and normalized through software pipeline for each image to have a mean pixel intensity value of 0.5. An open source machine learning algorithm, originally developed to predict fluorescence labels on unlabeled transmitted light microscopy cell images, was trained using this set of normalized z-stacks on a single CPU machine. Through transfer learning, the algorithm used knowledge acquired from its previous training sessions to learn the new task. Once trained, the algorithm was used to predict morphology of nuclei using normalized cell membrane fluorescence images as input. Predictions were compared to the ground truth fluorescence nuclei images. Results: After one week of training, using one cell membrane z-stack (20 images) and corresponding nuclei label, results showed qualitatively good predictions on training set. The algorithm was able to accurately predict nuclei locations as well as shape when fed only fluorescence membrane images. Similar training sessions with improved membrane image quality, including clear lining and shape of the membrane, clearly showing the boundaries of each cell, proportionally improved nuclei predictions, reducing errors relative to ground truth. Discussion: These results show the potential of pre-trained machine learning algorithms to predict cell morphology using relatively small amounts of data and training time, eliminating the need of using multiple labels in immunofluorescence experiments. With further training, the algorithm is expected to predict different labels (e.g., focal-adhesion sites, cytoskeleton), which can be added to the automatic machine learning pipeline for direct input into Principal Component Analysis (PCA) for generation of virtual-cell mechanical models.

Keywords: cell morphology prediction, computational machine learning, fluorescence microscopy, virtual-cell models

Procedia PDF Downloads 192

Authors: Shruti Soudi, Anushka Nayak

Abstract:

Altruism is a voluntary helping behavior that is not motivated by rewards. The empathy-altruism hypothesis states that altruistic behavior results from empathy, a constant emotional response between the helper and the individual in need. Individual variances in familiar ways of thinking, feeling, and acting are called personalities. The personality of an individual determines their behavior. More importantly, Adler was among the first psychologists to document the importance of birth order on personality. The present study aims to understand the influence of personality and birth order on altruism. A questionnaire consisting of standardized tools to measure altruism (Hindi Self Report Altruism Scale) and personality (Big Five Personality Inventory) will aid in studying the relationship between these variables among young adults in India. A statistical analysis of the data will be completed using ANOVA and T-Test in the SPSS Software.

Keywords: altruism, personality, birth order, ANOVA, young adults

Procedia PDF Downloads 60

Authors: C. S. Paglia

Abstract:

The deformation and the crystallization in a 7075-T651 friction stir weld, in particular for regions directly in contact with the mechanical action of the rotating probe, have been investigated by means of optical microscopy. The investigation enabled to identify regions of the weld differently affected by the deformation caused by the welding process. The highly deformed grains in the horizontal direction close to the plate margin were indicative of shear movements along the horizontal plane, while highly deformed grains along the plate margin in the vertical direction were indicative of vertical shear movements of opposite directions, which superimposed the shear movement along the horizontal plane. The vertical shear movements were not homogeneous through the plate thickness. The microstructure indicated that after the probe passes, the grain growth may take place under static conditions. The small grains microstructure of the nugget region, formed after the main dynamic recrystallization process, develops to an equiaxed microstructure. A material transport influenced by the rotating shoulder was also observed from the trailing to the advancing side of the weld.

Keywords: AA7075-T651, friction stir welding, deformation, crystallization

Procedia PDF Downloads 112

Authors: A. T. Muruviwa

Abstract:

To-date, the discourse on corporate social responsibility (CSR) has primarily centred on the actions and inactions of corporations; hence, the dominant focus on CSR has been on impacts and outcomes. The obscuring effect of this approach has, arguably, resulted in the emergence of what may be termed a ‘Northern’ agenda on CSR theory and practice, in contrast to an emergency ‘Southern’ discourse, which appears to highlight the crucial issues of poverty reduction, infrastructure development and the broader questions of social provisioning and community empowerment. Some scholars have explicitly called for a CSR research agenda that focuses on the 'reciprocal duties' of the stakeholders in the CSR process rather than fixate on the actions and inactions of business. It is against the backdrop of these contestations that this study assesses the reciprocal relationships amongst CSR stakeholders in a Zimbabwean platinum mining town, with a view to demonstrating how such relationships – and the expectations and obligations embedded in them – impact on the success or failure of CSR initiatives. The existence of mutual relations between the corporation and its stakeholders signifies the successes of CSR processes and hence the outcomes. The company is Zimplats Mining Company; the community is Mhondoro-Ngezi, and the stakeholders are clearly identified in the study. The study utilised a triangulated design, with data collected using a mini survey, focus groups, in-depth interview and observation. The key findings are that the CSR process in the study community is dominated by the mining company. Despite the existence of a CSR framework that recognises government, local leaders and community members as legitimate stakeholders, there is little evidence of concrete contributions made by these stakeholders towards the realisation of CSR objectives. As a result, the community development process – in so far as CSR is concerned – fails to address the developmental concerns of the various stakeholders. On the basis of these findings, the study concludes that there is a crisis of reciprocity in the CSR process in Mhondoro-Ngezi, and that a situation where the conceptualisation of local development needs and the deployment of specific development tools seems to be driven by one stakeholder almost to the exclusion of all others, can only present contradictory development outcomes. The significance of this study is that it allows for the development of a more nuanced and robust CSR discourse. Rather than focusing on the corporate and stakeholder perspectives and outcomes of CSR initiatives, this study examines the CSR- development nexus by interrogating the idea of reciprocal responsibility as a sin qua non to CSR success. This analytical strategy and focus allow the researcher to gain a clear understanding of how stakeholder relationships and duties influence CSR processes and also the overall outcome. At a more practical level, the findings of the study should help to shape the policy on corporate community relationships with a view to enhancing the role of mining in development.

Keywords: community development, processes, reciprocity, stakeholders

Procedia PDF Downloads 335

Authors: Hayrettin Eroglu, Adem Kara

Abstract:

Recently there has been significant attention given to imaging of the biological tissues via microwave imaging techniques. In this study, a phantom for the test and calibration of Microwave imaging used in detecting unhealthy breast structure or tumors was produced by using sol gel method. The liquid and gel phantoms being used nowadays are not durable due to evaporation and their organic ingredients, hence a new design was proposed. This phantom was fabricated from materials that were widely available (water, salt, gelatin, and glycerol) and was easy to make. This phantom was aimed to be better from the ones already proposed in the literature in terms of its durability and stability. S Parameters of phantom was measured with 1-18 GHz Probe Kit and permittivity was calculated via Debye method in “85070” commercial software. One, three, and five-week measurements were taken for this phantom. Finally, it was verified that measurement results were very close to the real biological tissue measurement results.

Keywords: phantom, breast tissue, cancer, microwave imaging

Procedia PDF Downloads 338

Authors: Edward J. Kansa, Pavel Holoborodko

Abstract:

Continuously differentiable radial basis functions (RBFs) are meshfree, converge faster as the dimensionality increases, and is theoretically spectrally convergent. When implemented on current single and double precision computers, such RBFs can suffer from ill-conditioning because the systems of equations needed to be solved to find the expansion coefficients are full. However, the Advanpix extended precision software package allows computer mathematics to resemble asymptotically ideal Platonic mathematics. Additionally, full systems with extended precision execute faster graphical processors units and field-programmable gate arrays because no branching is needed. Sparse equation systems are fast for iterative solvers in a very limited number of cases.

Keywords: partial differential equations, Meshfree radial basis functions, , no restrictions on spatial dimensions, Extended arithmetic precision.

Procedia PDF Downloads 140

Authors: Yusuf A. Bako, Olubunmi O. Kolawole

Abstract:

This study sought to establish the effect of recruitment and selection on the employee performance in hospitality industries. The success of any organization in this modern business environment depends on the caliber of the manpower that steer the affairs of the organization. History has shown that recruitment and selection as a function of human resources management practices have a pivotal role in determining the level of employee performance in an organization. The hospitality industries have been faced with challenges of performance due to unconventional selection and placement practices in terms of poor policy in selecting candidate, inconsistency in selection process, sidetracking employment test and interview, godfatherism and regional selection process etc. The overall objective of the study was to determine how recruitment and selection affect employee performance in hospitality industry in Ogun State, Nigeria. This study adopts descriptive and inferential research design while population was drawn from leading hotels in Ogun State, Nigeria. The samples size was 100 employees and questionnaire was used to collect data while Cronbach alpha was used to test the instrument. The result of the study reveals that correlation between employee performance and recruitment and selection were highly significant.

Keywords: employee performance, human resources management, practices, recruitment, selection

Procedia PDF Downloads 353

Authors: M. Nemer, E. I. Konukseven

Abstract:

In this paper, a motion generation algorithm for a six Degrees of Freedom (DoF) robotic hand in a static environment is presented. The purpose of developing this method is to be used in the path generation of the end-effector for edge finishing and inspection processes by utilizing the CAD model of the considered workpiece. Nonetheless, the proposed algorithm may be extended to be applicable for other similar manufacturing processes. A software package programmed in the application programming interface (API) of SolidWorks generates tool path data for the robot. The proposed method significantly simplifies the given problem, resulting in a reduction in the CPU time needed to generate the path, and offers an efficient overall solution. The ABB IRB2000 robot is chosen for executing the generated tool path.

Keywords: CAD-based tools, edge deburring, edge scanning, offline programming, path generation

Procedia PDF Downloads 275

Authors: Shih-Jie Ma, Jui-Hsu Hsiao, Ming-Ying Hsieh, Shin-Yan Yang, Chun-Han Yeh, Kuo-Chun Su

Abstract:

In Taiwan, social enterprises and non-profit organizations (NPOs) are not familiar with innovative business models, such as live streaming. In 2019, a brand new course called internet celebrity training project is introduced to them by the Social Innovation Lab. The Goal of this paper is to evaluate the effect of this project, to explore the role of new technology (internet live stream) in business process management (BPM), and to analyze how live stream programs can assist social enterprises in creating new business models. Social Innovation, with the purpose to solve social issues in innovative ways, is one of the most popular topics in the world. Social Innovation Lab was established in 2017 by Executive Yuan in Taiwan. The vision of Social Innovation Lab is to exploit technology, innovation and experimental methods to solve social issues, and to maximize the benefits from government investment. Social Innovation Lab aims at creating a platform for both supply and demand sides of social issues, to make social enterprises and start-ups communicate with each other, and to build an eco-system in which stakeholders can make a social impact. Social Innovation Lab keeps helping social enterprises and NPOs to gain better publicity and to enhance competitiveness by facilitating digital transformation. In this project, Social Innovation Lab exerted the influence of social media such as YouTube and Facebook, to make social enterprises and start-ups adjust their business models by using the live stream of social media, which becomes one of the tools to expand their market and diversify their sales channels. Internet live stream training courses were delivered in different regions of Taiwan in 2019, including Taitung, Taichung, Kaohsiung and Hualien. Through these courses, potential groups and enterprises were cultivated to become so-called internet celebrities. With their concern about social issues in mind, these internet celebrities know how to manipulate social media to make a social impact in different fields, such as aboriginal people, food and agriculture, LOHAS (Lifestyles of Health and Sustainability), environmental protection and senior citizens. Participants of live stream training courses in Taiwan are selected to take in-depth interviews and questionnaire surveys. Results indicate that the digital transformation process of social enterprises and NPOs can be successful by implementing business process reengineering, a significant change made by social innovation internet celebrities. Therefore, this project can be the new driving force to facilitate the business model transformation in Taiwan.

Keywords: business process management, digital transformation, live stream, social innovation

Procedia PDF Downloads 134

Authors: Aleksandar Jovanovic, Katarina Kukic, Ana Uzelac, Dusan Teodorovic

Abstract:

Wisdom of the Crowd (WoC) is a decentralized method that uses the collective intelligence of humans. Individual guesses may be far from the target, but when considered as a group, they converge on optimal solutions for a given problem. We will utilize WoC to address the challenge of controlling traffic lights within intersections from the streets of Kragujevac, Serbia. The problem at hand falls within the category of NP-hard problems. We will employ an algorithm that leverages the swarm intelligence of bees: Bee Colony Optimization (BCO). Data regarding traffic signal timing at a single intersection will be gathered from citizens through a survey. Results obtained in that manner will be compared to the BCO results for different traffic scenarios. We will use Vissim traffic simulation software as a tool to compare the performance of bees’ and humans’ collective intelligence.

Keywords: wisdom of the crowd, traffic signal control, combinatorial optimization, bee colony optimization

Procedia PDF Downloads 97

Authors: Jahedul Islam Chowdhury, Bao Kha Nguyen, David Thornhill, Roy Douglas, Stephen Glover

Abstract:

Organic Rankine Cycle (ORC) is the most commonly used method for recovering energy from small sources of heat. The investigation of the ORC in supercritical condition is a new research area as it has a potential to generate high power and thermal efficiency in a waste heat recovery system. This paper presents a steady state ORC model in supercritical condition and its simulations with a real engine’s exhaust data. The key component of ORC, evaporator, is modelled using finite volume method, modelling of all other components of the waste heat recovery system such as pump, expander and condenser are also presented. The aim of this paper is to investigate the effects of mass flow rate and evaporator outlet temperature on the efficiency of the waste heat recovery process. Additionally, the necessity of maintaining an optimum evaporator outlet temperature is also investigated. Simulation results show that modification of mass flow rate is the key to changing the operating temperature at the evaporator outlet.

Keywords: Organic Rankine cycle, supercritical condition, steady state model, waste heat recovery

Procedia PDF Downloads 394

Authors: Maiko Kiyohara, Toshiki Ito

Abstract:

In this study, we used a psychotherapy process for patient with dissociative disorder and the graphic Rorschach (Digital version) (GRD). A dissociative disorder is a type of dissociation characterized by multiple alternating personalities (also called alternate identity or another identity). "dissociation" is a state in which consciousness, memory, thinking, emotion, perception, behavior, body image, and so on are divided and experienced. Dissociation symptoms, such as lack of memory, are seen, and the repetition of blanks in daily events causes serious problems in life. Although the pathological mechanism of dissociation has not yet been fully elucidated, it is said that it is caused by childhood abuse or shocking trauma. In case of Japan, no reliable data has been reported on the number of patients and prevalence of dissociative disorders, no drug is compatible with dissociation symptoms, and no clear treatment has been established. GRD is a method that the author revised in 2017 to a Graphic Rorschach, which is a special technique for subjects to draw language responses when enforce Rorschach. GRD reduces the burden on both the subject and the examiner, reduces the complexity of organizing data, improves the simplicity of organizing data, and improves the accuracy of interpretation by introducing a tablet computer during the drawing reaction. We are conducting research for the purpose. The patient in this case is a woman in her 50s, and has multiple personalities since childhood. At present, there are about 10 personalities whose main personality is just grasped. The patients is raising her junior high school sons as single parent, but personal changes often occur at home, which makes the home environment inferior and economically oppressive, and has severely hindered daily life. In psychotherapy, while a personality different from the main personality has appeared, I have also conducted psychotherapy with her son. In this case, the psychotherapy process and the GRD were performed to understand the personality characteristics, and the possibility of therapeutic significance to personality integration is reported.

Keywords: GRD, dissociative disorder, a case study of psychotherapy process, dissociation

Procedia PDF Downloads 103

Authors: Elena Krutskikh, Elena Khvatova

Abstract:

In tertiary settings expanding students’ vocabulary and teaching discursive competence is seen as one of the chief goals of a professional development course. However, such a focus often is detrimental to students’ cognitive competences, such as analysis, synthesis, and creative processing of information, and deprives students of motivation for self-improvement and self-development of language skills. The presentation is going to argue that in an ESP course special attention should be paid to reading/listening which can promote understanding and using the language as a tool for solving significant real world problems, including professional ones. It is claimed that in the learning process it is necessary to maintain a balance between the content and the linguistic aspect of the educational process as language acquisition is inextricably linked with mental activity and the need to express oneself is a primary stimulus for using a language. A study conducted among undergraduates indicates that they place a premium on quality materials that motivate them and stimulate their further linguistic and professional development. Thus, more demands are placed on study materials that should contain new information for students and serve not only as a source of new vocabulary but also prepare them for real tasks related to professional activities.

Keywords: critical reading, english for professional development, english for specific purposes, high order thinking skills, lexical approach, vocabulary acquisition

Procedia PDF Downloads 151

Authors: Derya Güler Aydin, Bahar Araz Takay

Abstract:

Two different forms of competition theories can be distinguished: Those theories that emphasize the equilibrating forces created by competition, and those emphasizing the disequilibrating forces. This difference can be attributed, among other things, to the differences regarding the functioning of the market economy; that is to say, the basic problem here is whether competition should be understood as a static state or a dynamic process. This study aims to analyze the dynamic competition theories by K. Marx and J. A. Schumpeter and neo- Schumperians all of which focus on the dynamic role played by competition through creating disequilibria, endogenous structural change and social transformation as a distinguishing characteristic of the market system. With this aim, in the first section, after examining the static, neoclassical competition theory, both Marx‟s theory, which is based on profit rate differentials, and Schumpeter‟s theory, which is based on the notion of “creative destruction”, will be discussed. In the second section, the long-term fluctuations, based on creative gales of destruction, the concept will be examined under the framework of techno-economic paradigm. It is argued that the dynamic, even disequilibrium tendencies created by the competition process should be regarded in both understanding the working of capitalism and social transformation of the system.

Keywords: competition, techno-enomic paradigm, Schumpeter, social evolution

Procedia PDF Downloads 225

Authors: Yi-Hsiang Pan, Ching-Hsiang Chen, Wei-Ting Hsu

Abstract:

The purpose of this study was to compare the learning effects of the sports education model (SEM) to those of the traditional teaching model (TTM) in physical education classes in terms of students learning motivation, action control, learning strategies, and learning performance. A quasi-experimental design was utilized in this study, and participants included two physical educators and four classes with a total of 94 students in grades 5 and 6 of elementary schools. Two classes implemented the SEM (n=47, male=24, female=23; age=11.89, SD=0.78) and two classes implemented the TTM (n=47, male=25, female=22, age=11.77; SD=0.66). Data were collected from these participants using a self-report questionnaire (including a learning motivation scale, action control scale, and learning strategy scale) and a game performance assessment instrument, and multivariate analysis of covariance was used to conduct statistical analysis. The findings of the study revealed that the SEM was significantly better than the TTM in promoting students learning motivation, action control, learning strategies, and game performance. It was concluded that the SEM could promote the mechanics of students self-regulated learning process, and thereby improve students movement performance.

Keywords: self-regulated learning theory, learning process, curriculum model, physical education

Procedia PDF Downloads 328

Authors: Vinay Kumar Vanjakula, Frank Adam

Abstract:

The generation of electricity through wind power is one of the leading renewable energy generation methods. Due to abundant higher wind speeds far away from shore, the construction of offshore wind turbines began in the last decades. However, the installation of offshore foundation-based (monopiles) wind turbines in deep waters are often associated with technical and financial challenges. To overcome such challenges, the concept of floating wind turbines is expanded as the basis of the oil and gas industry. For such a floating system, stabilization in harsh conditions is a challenging task. For that, a robust heavy-weight gravity anchor is needed. Transportation of such anchor requires a heavy vessel that increases the cost. To lower the cost, the gravity anchor is designed with ballast chambers that allow the anchor to float while towing and filled with water when lowering to the planned seabed location. The presence of such a large structure may influence the flow field around it. The changes in the flow field include, formation of vortices, turbulence generation, waves or currents flow breaking and pressure differentials around the seabed sediment. These changes influence the installation process. Also, after installation and under operating conditions, the flow around the anchor may allow the local seabed sediment to be carried off and results in Scour (erosion). These are a threat to the structure's stability. In recent decades, rapid developments of research work and the knowledge of scouring on fixed structures (bridges and monopiles) in rivers and oceans have been carried out, and very limited research work on scouring around a bluff-shaped gravity anchor. The objective of this study involves the application of different numerical models to simulate the anchor towing under waves and calm water conditions. Anchor lowering involves the investigation of anchor movements at certain water depths under wave/current. The motions of anchor drift, heave, and pitch is of special focus. The further study involves anchor scour, where the anchor is installed in the seabed; the flow of underwater current around the anchor induces vortices mainly at the front and corners that develop soil erosion. The study of scouring on a submerged gravity anchor is an interesting research question since the flow not only passes around the anchor but also over the structure that forms different flow vortices. The achieved results and the numerical model will be a basis for the development of other designs and concepts for marine structures. The Computational Fluid Dynamics (CFD) numerical model will build in OpenFOAM and other similar software.

Keywords: anchor lowering, anchor towing, gravity anchor, computational fluid dynamics, scour

Procedia PDF Downloads 153

Authors: Boubaker Fezzani, Ridha Ben Cheikh, Tarek Rouissi

Abstract:

In this work the original ADM1, implemented in the simulation software package MATLAB/Simulink, was modified and adapted and applied to reproduce the experimental results of the mesophilic anaerobic digestion of Esperto paper industry wastewater in a batch digester. The data set from lab-scale experiment runs were used to calibrate and validate the model. The simulations’ results indicated that the modified ADM1 was able to predict reasonably well the steady state results of gas flows, methane and carbon dioxide contents, pH and total volatile fatty acids (TVFA) observed with all influents concentrations.

Keywords: anaerobic digestion, mathematical modelling, Simulation, ADM1, batch digester, esparto paper industry effluent, mesophilic temperature

Procedia PDF Downloads 389

Authors: Rosa Buxeda, Lorenzo Saliceti-Piazza, Rodolfo J. Romañach, Luis Ríos, Sandra L. Maldonado-Ramírez

Abstract:

Biopharmaceuticals manufacturing is one of the major economic activities worldwide. Ninety-three percent of the workforce in a biomanufacturing environment concentrates in production-related areas. As a result, strategic collaborations between industry and academia are crucial to ensure the availability of knowledgeable workforce needed in an economic region to become competitive in biomanufacturing. In the past decade, our institution has been a key strategic partner with multinational biotechnology companies in supplying science and engineering graduates in the field of industrial biotechnology. Initiatives addressing all levels of the educational pipeline, from K-12 to college to continued education for company employees have been established along a ten-year span. The Amgen BioTalents Program was designed to provide undergraduate science and engineering students with training in biomanufacturing. The areas targeted by this educational program enhance their academic development, since these topics are not part of their traditional science and engineering curricula. The educational curriculum involved the process of producing a biomolecule from the genetic engineering of cells to the production of an especially targeted polypeptide, protein expression and purification, to quality control, and validation. This paper will report and describe the implementation details and outcomes of the first sessions of the program.

Keywords: biomanufacturing curriculum, interdisciplinary learning, workforce development, industry-academia partnering

Procedia PDF Downloads 270