Search results for: support shape

Authors: Marine Segui, Matthieu Mantilla, Ruxandra Mihaela Botez

Abstract:

This research is the part of a major project at the Research Laboratory in Active Controls, Avionics and Aeroservoelasticity (LARCASE) aiming to improve a Cessna Citation X aircraft cruise performance with an application of the morphing wing technology on its horizontal tail. However, the horizontal stabilizer of the Cessna Citation X turns around its span axis with an angle between -8 and 2 degrees. Within this range, the horizontal stabilizer generates certainly some unwanted drag. To cancel this drag, the LARCASE proposes to trim the aircraft with a horizontal stabilizer equipped by a morphing wing technology. This technology aims to optimize aerodynamic performances by changing the conventional horizontal tail shape during the flight. As a consequence, this technology will be able to generate enough lift on the horizontal tail to balance the aircraft without an unwanted drag generation. To conduct this project, an accurate aerodynamic model of the horizontal tail is firstly required. This aerodynamic model will finally allow precise comparison between a conventional horizontal tail and a morphed horizontal tail results. This paper presents how this aerodynamic model was designed. In this way, it shows how the 2D geometry of the horizontal tail was collected and how the unknown airfoil’s shape of the horizontal tail has been recovered. Finally, the complete horizontal tail airfoil shape was found and a comparison between aerodynamic polar of the real horizontal tail and the horizontal tail found in this paper shows a maximum difference of 0.04 on the lift or the drag coefficient which is very good. Aerodynamic polar data of the aircraft horizontal tail are obtained from the CAE Inc. level D research aircraft flight simulator of the Cessna Citation X.

Keywords: aerodynamic, Cessna, citation, coefficient, Datcom, drag, lift, longitudinal, model, OpenVSP

Procedia PDF Downloads 346

Authors: Elias K. Maragos, Petros E. Maravelakis

Abstract:

In Dynamic Data Envelopment Analysis (DDEA), which is a subfield of Data Envelopment Analysis (DEA), the productivity of Decision Making Units (DMUs) is considered in relation to time. In this case, as it is accepted by the most of the researchers, there are outputs, which are produced by a DMU to be used as inputs in a future time. Those outputs are known as intermediates. The common models, in DDEA, do not take into account the shape of the distribution of those inputs, outputs or intermediates data, assuming that the distribution of the virtual value of them does not deviate from linearity. This weakness causes the limitation of the accuracy of the analytical power of the traditional DDEA models. In this paper, the authors, using the concept of piecewise linear inputs and outputs, propose an extended DDEA model. The proposed model increases the flexibility of the traditional DDEA models and improves the measurement of the dynamic performance of DMUs.

Keywords: Dynamic Data Envelopment Analysis, DDEA, piecewise linear inputs, piecewise linear outputs

Procedia PDF Downloads 141

Authors: Shih-Wen Hsiao, Chu-Hsuan Lee, Rong-Qi Chen

Abstract:

When it comes to last, it is regarded as the critical foundation of shoe design and development. Not only the last relates to the comfort of shoes wearing but also it aids the production of shoe styling and manufacturing. In order to enhance the efficiency and application of last development, a computer aided methodology for customized last form designs is proposed in this study. The reverse engineering is mainly applied to the process of scanning for the last form. Then the minimum energy is used for the revision of surface continuity, the surface of the last is reconstructed with the feature curves of the scanned last. When the surface of a last is reconstructed, based on the foundation of the proposed last form reconstruction module, the weighted arithmetic mean method is applied to the calculation on the shape morphing which differs from the grading for the control mesh of last, and the algorithm of subdivision is used to create the surface of last mesh, thus the feet-fitting 3D last form of different sizes is generated from its original form feature with functions remained. Finally, the practicability of the proposed methodology is verified through later case studies.

Keywords: 3D last design, customization, reverse engineering, weighted morphing, shape blending

Procedia PDF Downloads 321

Authors: Mohammad Shahjahan, Md. Monoarul Haque

Abstract:

In the research work information and data were collected from both types of sources, direct and indirect. Numerological, qualitative and participatory analysis methods have been followed. There were two principal sources of collecting information and data. Firstly, the data provided by the service recipients (300 nos. of women and children victims) in the Victim Support Centre and service providing policemen, executives and staffs (60 nos.). Secondly, data collected from Specialists, Criminologists and Sociologists involved in victim support services through Consultative Interview, KII, Case Study and FGD etc. The initial data collection has been completed with the help of questionnaires as per strategic variations and with the help of guidelines. It is to be noted that the main objective of this research was to determine whether services provided to the victims for their facilities, treatment/medication and rehabilitation by different government/non-government organizations was veritable at all. At the same time socio-economic background and demographic characteristics of the victims have also been revealed through this research. The results of the study show that although the number of victims has increased gradually due to socio-economic, political and cultural realities in Bangladesh, the number of victim support centers has not increased as expected. Awareness among the victims about the effectiveness of the 8 centers working in this regard is also not up to the mark. Two thirds of the victims coming to get service were not cognizant regarding the victim support services at all before getting the service. Most of those who have finally been able to come under the services of the Victim Support Center through various means, have received sheltering (15.5%), medical services (13.32%), counseling services (13.10%) and legal aid (12.66%). The opportunity to stay in security custody and psycho-physical services were also notable. Usually, women and children from relatively poor and marginalized families of the society come to victim support center for getting services. Among the women, young unmarried women are the biggest victims of crime. Again, women and children employed as domestic workers are more affected. A number of serious negative impacts fall on the lives of the victims. Being deprived of employment opportunities (26.62%), suffering from psycho-somatic disorder (20.27%), carrying sexually transmitted diseases (13.92%) are among them. It seems apparent to urgently enact distinct legislation, increase the number of Victim Support Centers, expand the area and purview of services and take initiative to increase public awareness and to create mass movement.

Keywords: crime, victim, support, Bangladesh

Procedia PDF Downloads 61

Authors: Miyako Oulevey, Kaori Tsutsui, David Lavallee, Naohiko Kohtake

Abstract:

The Japan Sports Agency has made efforts to unify several career support programs for Olympic athletes prior to the 2020 Tokyo Olympics. One of the programs, the Japan Olympic Committee Career Academy (JCA) was established in 2008 for Olympic athletes at their retirement. Research focusing on the service content of sport career support programs can help athletes experience a more positive transition. This study was designed to investigate the service content of the JCA program in relation to athletes’ career transition needs, including any differences of the reasons for retirement between Summer/Winter and Male/Female Olympic athletes, and to suggest the directions of how to unify the career support programs in Japan after hosting the Olympic Games using sport career transition models. Semi-structured interviews were conducted and analyzed the JCA director who started and managed the program since its inception, and a total of 15 conceptual categories were generated by the analysis. Four conceptual categories were in the result of “JCA situation”, 4 conceptual categories were in the result of “Athletes using JCA”, and 7 conceptual categories were in the result of “JCA current difficulties”. Through the analysis it was revealed that: the JCA had occupational supports for both current and retired Olympic athletes; other supports such as psychological support were unclear due to the lack of psychological professionals in JCA and the difficulties collaborating with other sports organizations; and there are differences in tendencies of visiting JCA, financial situations, and career choices depending on Summer/Winter and Male/Female athletes.

Keywords: career support programs, causes of career termination, Olympic athlete, Olympic committee

Procedia PDF Downloads 122

Authors: Ayna Yusubova, Bart Clarysse

Abstract:

This paper explores role of research institutes in creation of support ecosystem for new technology-based ventures. Previous literature introduced research institutes as part of business and knowledge ecosystem, very few studies are available that consider a research institute as an ecosystem that support high-tech startups at every stage of development. Based on a resource-based view and a stage-based model of high-tech startups growth, this study aims to analyze how a research institute builds a startup support ecosystem by attracting different stakeholders in order to help startups to overcome resource. This paper is based on an in-depth case study of public research institute that focus on development of entrepreneurial ecosystem in a developed region. Analysis shows that the idea generation stage of high-tech startups that related to the invention and development of product or technology for commercialization is associated with a lack of critical knowledge resources. Second, at growth phase that related to market entrance, high-tech startups face challenges associated with the development of their business network. Accordingly, the study shows the support ecosystem that research institute creates helps high-tech startups overcome resource gaps in order to achieve a successful transition from one phase of growth to the next.

Keywords: new technology-based firms, ecosystems, resources, business incubators, research instutes

Procedia PDF Downloads 239

Authors: S. B. Kerur, B. S. Murgayya

Abstract:

The development of micro and nano particle is challenging task and the study of the behavior of material at the micro level is gaining importance as their behavior at micro/nano level is different. These micro particle are being used as a sensing element to measure and detects the hazardous chemical, gases, explosives and biological agents. In the present study, finite element method is used for static and dynamic analysis of simple and composite cantilever beams of different shapes. The present FE model is validated with available analytical results and various parameters like shape, materials properties, damped and undamped conditions are considered for the numerical study. The results show the effects of shape change on the natural frequency and as these are used with fluid for chemical applications, the effect of damping due to viscous nature of fluid are simulated by considering different damping coefficient effect on the dynamic behavior of cantilever beams. The obtained results show the effect of these parameters can be effectively utilized based on system requirements.

Keywords: micro, FEM, dynamic, cantilever beam

Procedia PDF Downloads 364

Authors: A. Tahar Djebbar

Abstract:

Modern technologies have penetrated all spheres of human life, education being one of them. This paper focuses the attention on the integration of technology-based education in the Algerian classroom in teaching foreign languages. It sheds light on a specific area of ICT application: ICT in English learning and teaching. Some Algerian teachers or tutors of English face many challenges among which the lack of teaching materials which are indispensable for transmitting knowledge to learners. Thus, they find themselves compelled to use online e-books or download them in PDF form to support their lessons. Teachers even download such teaching materials like pictures, videos, audios, podcasts, and flash cards from the internet and store them in their Flash USBs to shape up the teaching-learning conditions. They use computers, data shows, and the internet so as to facilitate the teaching–learning process in the classroom. Hence, technology has become a must in the Algerian classroom especially in teaching English which has become a very important language in a national and an international level. This study aims at showing that Algerian tutors/teachers who take up the challenge of getting involved in the technology-enhanced language learning and teaching in the Algerian schools and universities face many obstacles.

Keywords: computer, communication, English, internet, learners, language acquisition, teaching, technology

Procedia PDF Downloads 610

Authors: Krzysztof Skiba, Zbigniew Czyz, Ksenia Siadkowska, Piotr Borowiec

Abstract:

The article presents selected concepts of technologies that use intelligent materials in aircraft in order to improve their performance. Most of the research focuses on solutions that improve the performance of fixed wing aircraft due to related to their previously dominant market share. Recently, the development of the rotorcraft has been intensive, so there are not only helicopters but also gyroplanes and unmanned aerial vehicles using rotors and vertical take-off and landing. There are many different technologies to change a shape of the aircraft or its elements. Piezoelectric, deformable actuator systems can be applied in the system of an active control of vibration dampening in the aircraft tail structure. Wires made of shape memory alloys (SMA) could be used instead of hydraulic cylinders in the rear part of the aircraft flap. The aircraft made of intelligent materials (piezoelectrics and SMA) is one of the NASA projects which provide the possibility of changing a wing shape coefficient by 200%, a wing surface by 50%, and wing deflections by 20 degrees. Active surfaces made of shape memory alloys could be used to control swirls in the flowing stream. An intelligent control system for helicopter blades is a method for the active adaptation of blades to flight conditions and the reduction of vibrations caused by the rotor. Shape memory alloys are capable of recovering their pre-programmed shapes. They are divided into three groups: nickel-titanium-based, copper-based, and ferromagnetic. Due to the strongest shape memory effect and the best vibration damping ability, a Ni-Ti alloy is the most commercially important. The subject of this work was to prepare a conceptual design of a rotor blade with SMA actuators. The scope of work included 3D design of the supporting rotor blade, 3D design of beams enabling to change the geometry by changing the angle of rotation and FEM (Finite Element Method) analysis. The FEM analysis was performed using NX 12 software in the Pre/Post module, which includes extended finite element modeling tools and visualizations of the obtained results. Calculations are presented for two versions of the blade girders. For FEM analysis, three types of materials were used for comparison purposes (ABS, aluminium alloy 7057, steel C45). The analysis of internal stresses and extreme displacements of crossbars edges was carried out. The internal stresses in all materials were close to the yield point in the solution of girder no. 1. For girder no. 2 solution, the value of stresses decreased by about 45%. As a result of the displacement analysis, it was found that the best solution was the ABS girder no. 1. The displacement of about 0.5 mm was obtained, which resulted in turning the crossbars (upper and lower) by an angle equal to 3.59 degrees. This is the largest deviation of all the tests. The smallest deviation was obtained for beam no. 2 made of steel. The displacement value of the second girder solution was approximately 30% lower than the first solution. Acknowledgement: This work has been financed by the Polish National Centre for Research and Development under the LIDER program, Grant Agreement No. LIDER/45/0177/L-9/17/NCBR/2018.

Keywords: aircraft, helicopters, shape memory alloy, SMA, smart material, unmanned aerial vehicle, UAV

Procedia PDF Downloads 113

Authors: Kamal, Dinesh Kumar, J. P. Narayan, Komal Rani

Abstract:

This paper presents the effects of shape of basement topography on the characteristics of the basin-generated surface (BGS) waves and associated average spectral amplification (ASA) in the 3D basins having circular surface area. Seismic responses were computed using a recently developed 3D fourth-order spatial accurate time-domain finite-difference (FD) algorithm based on parsimonious staggered-grid approximation of 3D viscoelastic wave equations. An increase of amplitude amplification and ASA towards the centre of different considered basins was obtained. Further, it may be concluded that ASA in basin very much depends on the impedance contrast, exposure area of basement to the incident wave front, edge-slope, focusing of the BGS-waves and sediment-damping. There is an urgent need of incorporation of a map of differential ground motion (DGM) caused by the BGS-waves as one of the output maps of the seismic microzonation.

Keywords: 3D viscoelastic simulation, basin-generated surface waves, maximum displacement, average spectral amplification

Procedia PDF Downloads 270

Authors: Kimton Opiyo, Elliot M. Berry, Patil Karamchand, Barnabas K. Natamba

Abstract:

Background: Postpartum depression (PPD) is a major psychiatric disorder that affects women soon after birth and in some cases, is a continuation of antenatal depression. Food insecurity (FI) and social support (SS) are known to be associated with major depressive disorder, and vice versa. This study was conducted to examine the interrelationships among FI, SS, and PPD among postpartum women in Gulu, a post-conflict region in Uganda. Methods: Cross-sectional data from postpartum women on depression symptoms, FI and SS were, respectively, obtained using the Center for Epidemiologic Studies-Depression (CES-D) scale, Individually Focused FI Access scale (IFIAS) and Duke-UNC functional social support scale. Standard regression methods were used to assess associations among FI, SS, and PPD. Results: A total of 239 women were studied, and 40% were found to have any PPD, i.e., with depressive symptom scores of ≥ 17. The mean ± standard deviation (SD) for FI score and SS scores were 6.47 ± 5.02 and 19.11 ± 4.23 respectively. In adjusted analyses, PPD symptoms were found to be positively associated with FI (unstandardized beta and standardized beta of 0.703 and 0.432 respectively, standard errors =0.093 and p-value < 0.0001) and negatively associated with SS (unstandardized beta and standardized beta of -0.263 and -0.135 respectively, standard errors = 0.111 and p-value = 0.019). Conclusions: Many women in this post-conflict region reported experiencing PPD. In addition, this data suggest that food security and psychosocial support interventions may help mitigate women’s experience of PPD or its severity.

Keywords: postpartum depression, food insecurity, social support, post-conflict region

Procedia PDF Downloads 147

Authors: A.H.Y. Lai, C. Teyra

Abstract:

In Taiwan, there are 16 official indigenous groups, accounting for 2.3% of the total population. Like other indigenous populations worldwide, indigenous peoples in Taiwan have poorer mental health because of their history of oppression and colonisation. Amid the negative narratives, the ethnic identity of cultural minorities is their unique psychological and cultural asset. Moreover, positive socialisation is found to be related to strong ethnic identity. Based on Phinney’s theory on ethnic identity development and social support theory, this study adopted a strength-based approach conceptualising ethnic identity as the central organising principle that linked perceived social support and mental health among indigenous adults in Taiwan. Aims. Overall aim is to examine the effect of ethnic identity and social support on mental health. Specific aims were to examine : (1) the association between ethnic identity and mental health; (2) the association between perceived social support and mental health ; (3) the indirect effect of ethnic identity linking perceived social support and mental health. Methods. Participants were indigenous adults in Taiwan (n=200; mean age=29.51; Female=31%, Male=61%, Others=8%). A cross-sectional quantitative design was implemented using data collected in the year 2020. Respondent-driven sampling was used. Standardised measurements were: Ethnic Identity Scale(6-item); Social Support Questionnaire-SF(6 items); Patient Health Questionnaire(9-item); and Generalised Anxiety Disorder(7-item). Covariates were age, gender and economic satisfaction. A four-stage structural equation modelling (SEM) with robust maximin likelihood estimation was employed using Mplus8.0. Step 1: A measurement model was built and tested using confirmatory factor analysis (CFA). Step 2: Factor covariates were re-specified as direct effects in the SEM. Covariates were added. The direct effects of (1) ethnic identity and social support on depression and anxiety and (2) social support on ethnic identity were tested. The indirect effect of ethnic identity was examined with the bootstrapping technique. Results. The CFA model showed satisfactory fit statistics: x^2(df)=869.69(608), p<.05; Comparative ft index (CFI)/ Tucker-Lewis fit index (TLI)=0.95/0.94; root mean square error of approximation (RMSEA)=0.05; Standardized Root Mean Squared Residual (SRMR)=0.05. Ethnic identity is represented by two latent factors: ethnic identity-commitment and ethnic identity-exploration. Depression, anxiety and social support are single-factor latent variables. For the SEM, model fit statistics were: x^2(df)=779.26(527), p<.05; CFI/TLI=0.94/0.93; RMSEA=0.05; SRMR=0.05. Ethnic identity-commitment (b=-0.30) and social support (b=-0.33) had direct negative effects on depression, but ethnic identity-exploration did not. Ethnic identity-commitment (b=-0.43) and social support (b=-0.31) had direct negative effects on anxiety, while identity-exploration (b=0.24) demonstrated a positive effect. Social support had direct positive effects on ethnic identity-exploration (b=0.26) and ethnic identity-commitment (b=0.31). Mediation analysis demonstrated the indirect effect of ethnic identity-commitment linking social support and depression (b=0.22). Implications: Results underscore the role of social support in preventing depression via ethnic identity commitment among indigenous adults in Taiwan. Adopting the strength-based approach, mental health practitioners can mobilise indigenous peoples’ commitment to their group to promote their well-being.

Keywords: ethnic identity, indigenous population, mental health, perceived social support

Procedia PDF Downloads 88

Authors: Vineetha Bettaiah, Heggere S. Ranganath

Abstract:

This paper presents a Hierarchical Piecewise Linear Approximation (HPLA) for the representation of time series data in which the time series is treated as a curve in the time-amplitude image space. The curve is partitioned into segments by choosing perceptually important points as break points. Each segment between adjacent break points is recursively partitioned into two segments at the best point or midpoint until the error between the approximating line and the original curve becomes less than a pre-specified threshold. The HPLA representation achieves dimensionality reduction while preserving prominent local features and general shape of time series. The representation permits course-fine processing at different levels of details, allows flexible definition of similarity based on mathematical measures or general time series shape, and supports time series data mining operations including query by content, clustering and classification based on whole or subsequence similarity.

Keywords: data mining, dimensionality reduction, piecewise linear representation, time series representation

Procedia PDF Downloads 256

Authors: Jian-Xiu Wan, Yao Yin

Abstract:

In complex terrain and poor geological conditions areas, Railway, highway and other transportation constructions are still strongly developing. However, various geological disasters happened such as landslide, rock heap and so on. According to the results of geological investigation, the form of skirt (trapezoidal), semicircle and triangle rock heaps are mainly due to complex internal force and external force, in a certain extent, which is related to the terrain, the nature of the rock mass, the supply area and the surface shape of rock heap. Combined with the above factors, discrete element numerical simulation of rock mass is established under different terrain conditions based on 3DEC, and accelerated formation process of rock heap under seismic action is simulated. The fragmentation structure supply area is calculated, in which the most dangerous area is located. At the same time, the formation mechanism and development process are studied in different terrain conditions, and the structure of rock heap is judged by section, which can provide a strong theoretical and technical support for the prevention and control of geological disasters.

Keywords: 3DEC, fragmentation structure, rock heap, slope, seismic action

Procedia PDF Downloads 280

Authors: Ka C. Lam, Oluwafunmibi S. Idowu

Abstract:

Building girth is important in building economics and mostly used in quantities take-off of various cost items. Literature suggests that the use of conceptual quantities can improve the accuracy of cost models. Girth or perimeter of a building can be used to estimate conceptual quantities. Hence, the current paper aims to model the perimeter-area function of buildings shapes for use at the conceptual design stage. A detailed literature review on existing building shape indexes was carried out. An empirical approach was used to study the relationship between area and the shortest length of a four-sided orthogonal polygon. Finally, a mathematical approach was used to establish the observed relationships. The empirical results obtained were in agreement with the mathematical model developed. A new equation termed “conceptual perimeter equation” is proposed. The equation can be used to estimate building envelope quantities such as external wall area, external finishing area and scaffolding area before sketch or detailed drawings are prepared.

Keywords: building envelope, building shape index, conceptual quantities, cost modelling, girth

Procedia PDF Downloads 314

Authors: Moreno Liso Lourdes

Abstract:

The industrial design protects the appearance of part or all of a product resulting from the features of, in particular, the lines, contours, colors, shape, texture or materials of the product itself or its ornamentation. The industrial property offers a different answer depending on the characteristics of the shape object of protection possible, including the trademark and industrial design. There are certain cases where the trademark right invalidate the exclusive right of the industrial design. This can occur in the following situations: 1st) collected as a sign design and trademarked; and 2nd) you want to trademark and protected as a form design (either registered or unregistered). You can either get a trade mark or design right in the same sign or form, provided it meets the legal definition of brand and design and meets the requirements imposed for the protection of each of them, even able to produce an overlap of protection. However, this double protection does not have many advantages. It is, therefore, necessary to choose the best form of legal protection according to the most adequate ratios. The diversity of rights that can use the creator of an industrial design to protect your job requires you to make a proper selection to prevent others, especially their competitors, taking advantage of the exclusivity that guarantees the law. It is necessary to choose between defending the interests of the parties through a judicial or extrajudicial procedure when the conflict arises. In this paper, we opted for the defense through mediation.

Keywords: industrial design, ADR, Law, EUIPO

Procedia PDF Downloads 220

Authors: Anita Burgund Isakov, Cristina Nunes, Nevenka Zegarac, Ana Antunes

Abstract:

Contemporary societies are facing a noticeable shift in family realities, urging to need for the development of new policies, service, and practice orientation that has application across different sectors who serves families with children across the world. A challenge for the field of family support is diversity in conceptual assumptions and epistemological frameworks. Since many disciplines and professionals are working in the family support field, there is a need to map and gain a deeper insight into the skills for the workforce in this field. Under the umbrella of the COST action 'The Pan-European Family Support Research Network: A bottom-up, evidence-based and multidisciplinary approach', a review of the current state of knowledge published from the European studies on family support workforce skills standards is performed. Contributing to the aim of mapping and catalogization of skills standards, key stages of literature review were identified in order to extract and systematize the data. We have considered inclusion and exclusion criteria for this literature review. Inclusion criteria were: a) families living with their children and families using family support services; different methodological approaches were included: qualitative, quantitative, mix method, literature review and theoretical reflections various topic appeared in journals like working with families that are facing difficulties or culturally sensitive practice and relationship-based approaches; b) the dates ranged from 1995 to February 2020. Articles published prior to 1995 were excluded due to modernization of family support services across world; c) the sources and languages included peer-reviewed articles published in scientific journals in English. Six databases were searched and once we have extracted all the relevant papers (n=29), we searched the list of reference in each and we found 11 additional papers. In total 40 papers have been extracted from six data basis. Findings could be summarized in: 1) only five countries emerged with production in the specific topic, that is, workforce skills to family support (UK, USA, Canada, Australia, and Spain), 2) studies revealed that diverse skills support family topics were investigated, namely the professional support skills to help families of neglected/abused children or in care; the professional support skills to help families with children who suffer from behavioral problems and families with children with disabilities; and the professional support skills to help minority ethnic parents, 3) social workers were the main targeted professionals' studies albeit other child protection workers were studied too, 4) the workforce skills to family support were grouped in three topics: the qualities of the professionals (attitudes and attributes); technical skills, and specific knowledge. The framework of analyses, literature strategy and findings with study limitations will be further discussed. As an implication, this study contributes and advocates for the structuring of a common base for cross-sectoral and interdisciplinary qualification standards for the family support workforce.

Keywords: family support, skill standards, systemic review, workforce

Procedia PDF Downloads 97

Authors: Tz-Bang Du, Cheng-Han Hsieh, Li-Ping Ju, Hung-Jie Liou

Abstract:

Polyether amines synthesize by secondary hydroxyl polyether diol play an important role in epoxy hardener. The low molecular weight product is used in low viscosity and high transparent polyamine product for the logo, ground cover, especially for wind turbine blade, while the high molecular weight products are used in advanced agricultures such as a high-speed railway. High-pressure reductive amination process is required for producing these amines. In the condition of higher than 150 atm pressure and 200 degrees Celsius temperature, supercritical ammonia is used as a reactant and also a solvent. It would be a great challenge to select a catalyst support for such high-temperature alkaline circumstance. In this study, we have established a six-autoclave-type (SAT) high-pressure reactor for amination catalyst screening, which six experiment conditions with different temperature and pressure could be examined at the same time. We synthesized copper-nickel catalyst on different shaped alumina catalyst support and evaluated the catalyst activity for high-pressure reductive amination of polypropylene glycol (PPG) by SAT reactor. Ball type gamma alumina, ball type activated alumina and pellet type gamma alumina catalyst supports are evaluated in this study. Gamma alumina supports have shown better activity on PPG reductive amination than activated alumina support. In addition, the catalysts are evaluated in fixed bed reactor. The diamine product was successfully synthesized via this catalyst and the strength of the catalysts is measured. The crush strength of blank supports is about 13.5 lb for both gamma alumina and activated alumina. The strength increases to 20.3 lb after synthesized to be copper-nickel catalyst. After test in the fixed bed high-pressure reductive amination process for 100 hours, the crush strength of the used catalyst is 3.7 lb for activated alumina support, 12.0 lb for gamma alumina support. The gamma alumina is better than activated alumina to use as catalyst support in high-pressure reductive amination process.

Keywords: high pressure reductive amination, copper nickel catalyst, polyether amine, alumina

Procedia PDF Downloads 205

Authors: Ambeck Celyne Tebid, Harry S. Rampa

Abstract:

The South African Education system recognises the need for all learners including those experiencing learning difficulties, to have access to a single unified system of education. For teachers to be pedagogically responsive to an increasingly diverse learner population without appropriate support has been proven to be unrealistic. As such, this has considerably hampered interest amongst teachers, especially those at the foundation phase to work within an Inclusive Education (IE) and training system. This qualitative study aimed at investigating foundation phase teachers’ experiences of school-based support teams (SBSTs) in two Full-Service (inclusive schools) and one Mainstream public primary school in the Gauteng province of South Africa; with particular emphasis on finding ways to supporting them, since teachers claimed they were not empowered in their initial training to teach learners experiencing learning difficulties. Hence, SBSTs were created at school levels to fill this gap thereby, supporting teaching and learning by identifying and addressing learners’, teachers’ and schools’ needs. With the notion that IE may be failing because of systemic reasons, this study uses Bronfenbrenner’s (1979) ecosystemic as well as Piaget’s (1980) maturational theory to examine the nature of support and experiences amongst teachers taking individual and systemic factors into consideration. Data was collected using in-depth, face-to-face interviews, document analysis and observation with 6 foundation phase teachers drawn from 3 different schools, 3 SBST coordinators, and 3 school principals. Data was analysed using the phenomenological data analysis method. Amongst the findings of the study is that South African full- service and mainstream schools have functional SBSTs which render formal and informal support to the teachers; this support varies in quality depending on the socio-economic status of the relevant community where the schools are situated. This paper, however, argues that what foundation phase teachers settled for as ‘support’ is flawed; as well as how they perceive the SBST and its role is problematic. The paper conclude by recommending that, the SBST should consider other approaches at foundation phase teacher support such as, empowering teachers with continuous practical experiences on how to deal with real classroom scenarios, as well as ensuring that all support, be it on academic or non-academic issues should be provided within a learning community framework where the teacher, family, SBST and where necessary, community organisations should harness their skills towards a common goal.

Keywords: foundation phase, full- service schools, inclusive education, learning difficulties, school-based support teams, teacher support

Procedia PDF Downloads 211

Authors: Edén Bojórquez, Victor Baca, Alfredo Reyes-Salazar, Jorge González

Abstract:

In this paper, simplified equations to predict maximum inter-story drift demands of steel framed buildings are proposed in terms of two ground motion intensity measures based on the acceleration spectral shape. For this aim, the maximum inter-story drifts of steel frames with 4, 6, 8 and 10 stories subjected to narrow-band ground motion records are estimated and compared with the spectral acceleration at first mode of vibration Sa(T1) which is commonly used in earthquake engineering and seismology, and with a new parameter related with the structural response known as INp. It is observed that INp is the parameter best related with the structural response of steel frames under narrow-band motions. Finally, equations to compute maximum inter-story drift demands of steel frames as a function of spectral acceleration and INp are proposed.

Keywords: intensity measures, spectral shape, steel frames, peak demands

Procedia PDF Downloads 369

Authors: P. Sankar, P. James Daniel Paul, Siddhant Sahu

Abstract:

A brief review of the empirical studies on the methodology of the stock market decision support would indicate that they are at a threshold of validating the accuracy of the traditional and the fuzzy, artificial neural network and the decision trees. Many researchers have been attempting to compare these models using various data sets worldwide. However, the research community is on the way to the conclusive confidence in the emerged models. This paper attempts to use the automotive sector stock prices from National Stock Exchange (NSE), India and analyze them for the intra-sectorial support for stock market decisions. The study identifies the significant variables and their lags which affect the price of the stocks using OLS analysis and decision tree classifiers.

Keywords: Indian automotive sector, stock market decisions, equity portfolio analysis, decision tree classifiers, statistical data analysis

Procedia PDF Downloads 459

Authors: Jiangyong Liu, Xiangxiang Xu, Bote Luo, Xiaoxue Luo, Jiang Zhu, Lingzhi Yi

Abstract:

To address the problems of non-linearity and high randomness of the original power load sequence causing the degradation of power load forecasting accuracy, a short-term load forecasting method is proposed. The method is based on the Least Square Support Vector Machine optimized by an Improved Sparrow Search Algorithm combined with the Variational Mode Decomposition proposed in this paper. The application of the variational mode decomposition technique decomposes the raw power load data into a series of Intrinsic Mode Functions components, which can reduce the complexity and instability of the raw data while overcoming modal confounding; the proposed improved sparrow search algorithm can solve the problem of difficult selection of learning parameters in the least Square Support Vector Machine. Finally, through comparison experiments, the results show that the method can effectively improve prediction accuracy.

Keywords: load forecasting, variational mode decomposition, improved sparrow search algorithm, least square support vector machine

Procedia PDF Downloads 80

Authors: A. Yongsheng Guo, B. Obedat. Abdulazeez, C. Xiaoxian Zhu

Abstract:

This study aimed to identify the barriers to the development of small and medium-sized enterprises (SMEs) in China and build a theoretical framework to evaluate the support provided by the authorities and institutions. A grounded theory approach was adopted to collect and analyze data. 32 interviews were conducted with SME managers, and open, axial and selective coding was utilized to develop themes. Based on institutional theory, grounded theory models were used to present findings. The findings showed that the main barriers in the business environment were defaulting on contracts, bureaucracy in procedures, lack of financial and legal support, limited intermediaries and channels, and poor quality of products and services. This study found that many programs were provided to support SMEs. A theoretical framework was developed to evaluate the performance of the programs from the managers’ perspective. The concepts of economy, efficiency and effectiveness were used to evaluate the perceived value of the programs. This study suggests that specialized programs are needed to suit sector-specific requirements, and creative packages are helpful in supporting SMEs' growth.

Keywords: business support, public economics, public programme, SME

Procedia PDF Downloads 17

Authors: Mahsa Namvari, Kari Ullakko

Abstract:

It is well-known that the Co-doping of ferromagnetic shape memory alloys (FSMAs) is a crucial tool to control their multifunctional properties. The present work investigates the use of small quantities of Co to fine-tune the transformation, structure, microstructure, mechanical and magnetic properties of the polycrystalline Ni₄₉.₈Mn₂₈.₅Ga₂₁.₇ (at.%) alloy, At Co concentrations of 1-1.5 at.%, a microstructure with an average grain size of about 2.00 mm was formed with a twin structure, enabling the experimental observation of magnetic-field-induced twin variant rearrangement. At higher levels of Co-doping, the grain size was essentially reduced, and the crystal structure of the martensitic phase became 2M martensite. The decreasing grain size and changing crystal structure are attributed to the progress of γ-phase precipitates. Alongside the academic aspect, the results of the present work point to the commercial advantage of fabricating 10M Co-doped Ni-Mn-Ga actuating elements made from large grains of polycrystalline ingots obtained by a standard melting facility instead of grown single crystals.

Keywords: Ni-Mn-Ga, ferromagnetic shape memory, martensitic phase transformation, grain growth

Procedia PDF Downloads 64

Authors: Pachawo Bisani, Goodall Nyirenda

Abstract:

The Malawi National Antiretroviral Therapy (NART) Electronic Medical Record (EMR) system was designed and developed with guidance from the Ministry of Health through the Department of HIV and AIDS (DHA) with the aim of supporting the management of HIV patient data and reporting in high prevalence ART clinics. As of 2021, the system has been scaled up to over 206 facilities across the country. The system is integrated with the clinical decision support system (CDSS) to assist healthcare providers in making a decision about an individual patient at a particular point in time. Despite NART EMR undergoing several evaluations and assessments, little has been done to evaluate the clinical decision support system in the NART EMR system. Hence, the study aimed to evaluate the use of CDSS in the NART EMR system in Malawi. The study adopted a mixed-method approach, and data was collected through interviews, observations, and questionnaires. The study has revealed that the CDSS tools were integrated into the ART clinic workflow, making it easy for the user to use it. The study has also revealed challenges in system reliability and information accuracy. Despite the challenges, the study further revealed that the system is effective and efficient, and overall, users are satisfied with the system. The study recommends that the implementers focus more on the logic behind the clinical decision-support intervention in order to address some of the concerns and enhance the accuracy of the information supplied. The study further suggests consulting the system's actual users throughout implementation.

Keywords: clinical decision support system, electronic medical record system, usability, antiretroviral therapy

Procedia PDF Downloads 66

Authors: Tobias Huwer, Thomas Bobek, Gunter Spöcker

Abstract:

Driving forces for enhancements in production are trends like digitalization and individualized production. Currently, such developments are restricted to assembly parts. Thus, complex freeform surfaces are not addressed in this context. The need for efficient use of resources and near-net-shape production will require individualized production of complex shaped workpieces. Due to variations between nominal model and actual geometry, this can lead to changes in operations in Computer-aided process planning (CAPP) to make CAPP manageable for an adaptive serial production. In this context, 3D CAD data can be a key to realizing that objective. Along with developments in the geometrical adaptation, a preceding inspection method based on CAD data is required to support the process planner by finding objective criteria to make decisions about the adaptive manufacturability of workpieces. Nowadays, this kind of decisions is depending on the experience-based knowledge of humans (e.g. process planners) and results in subjective decisions – leading to a variability of workpiece quality and potential failure in production. In this paper, we present an automatic part inspection method, based on design and measurement data, which evaluates actual geometries of single workpiece preforms. The aim is to automatically determine the suitability of the current shape for further machining, and to provide a basis for an objective decision about subsequent adaptive manufacturability. The proposed method is realized by a workflow-based approach, keeping in mind the requirements of industrial applications. Workflows are a well-known design method of standardized processes. Especially in applications like aerospace industry standardization and certification of processes are an important aspect. Function blocks, providing a standardized, event-driven abstraction to algorithms and data exchange, will be used for modeling and execution of inspection workflows. Each analysis step of the inspection, such as positioning of measurement data or checking of geometrical criteria, will be carried out by function blocks. One advantage of this approach is its flexibility to design workflows and to adapt algorithms specific to the application domain. In general, within the specified tolerance range it will be checked if a geometrical adaption is possible. The development of particular function blocks is predicated on workpiece specific information e.g. design data. Furthermore, for different product lifecycle phases, appropriate logics and decision criteria have to be considered. For example, tolerances for geometric deviations are different in type and size for new-part production compared to repair processes. In addition to function blocks, appropriate referencing systems are important. They need to support exact determination of position and orientation of the actual geometries to provide a basis for precise analysis. The presented approach provides an inspection methodology for adaptive and part-individual process chains. The analysis of each workpiece results in an inspection protocol and an objective decision about further manufacturability. A representative application domain is the product lifecycle of turbine blades containing a new-part production and a maintenance process. In both cases, a geometrical adaptation is required to calculate individual production data. In contrast to existing approaches, the proposed initial inspection method provides information to decide between different potential adaptive machining processes.

Keywords: adaptive, CAx, function blocks, turbomachinery

Procedia PDF Downloads 282

Authors: Hyunho Shin, Jaekwang Jung, Jeongho Park, Sungwon Hwang

Abstract:

For the application of graphene quantum dots (GQDs) to optoelectronic nanodevices, it is of critical importance to understand the mechanisms which result in novel phenomena of their light absorption/emission. The optical transitions are known to be available up to ~6 eV in GQDs, especially useful for ultraviolet (UV) photodetectors (PDs). Here, we present size-dependent shape/edge-state variations of GQDs and visible photoluminescence (PL) showing anomalous size dependencies. With varying the average size (da) of GQDs from 5 to 35 nm, the peak energy of the absorption spectra monotonically decreases, while that of the visible PL spectra unusually shows nonmonotonic behaviors having a minimum at diameter ∼17 nm. The PL behaviors can be attributed to the novel feature of GQDs, that is, the circular-to-polygonal-shape and corresponding edge-state variations of GQDs at diameter ∼17 nm as the GQD size increases, as demonstrated by high resolution transmission electron microscopy. We believe that such a comprehensive scheme in designing device architecture and the structural formulation of GQDs provides a device for practical realization of environmentally benign, high performance flexible devices in the future.

Keywords: graphene, quantum dot, size, photoluminescence

Procedia PDF Downloads 270

Authors: Stela Doncheva

Abstract:

Postpartum distress, encompassing depressive symptoms, obsessions, and anxiety, remains a subject of significant scientific interest due to its prevalence among individuals giving birth. This critical and transformative period presents a multitude of factors that impact women's health. On the one hand, variables such as social support, satisfaction in romantic relationships, shared newborn care, and birth satisfaction directly affect the mental well-being of new mothers. On the other hand, the interplay of hormonal changes, personality characteristics, emotional difficulties, and the profound life adjustments experienced by mothers can profoundly influence their self-esteem and overall physical and emotional well-being. This paper extensively explores the factors of alexithymia, social support, partners' support, and birth satisfaction to gain deeper insights into their impact on postpartum distress. Utilizing a qualitative survey consisting of six self-reflective questionnaires, this study collects valuable data regarding the individual postpartum experiences of Bulgarian mothers. The primary objective is to enrich our understanding of the complex factors involved in the development of postpartum distress during this crucial period. The results shed light on the intricate nature of the problem and highlight the significant influence of bio-psycho-social elements. By contributing to the existing knowledge in the field, this research provides valuable implications for the development of interventions and support systems tailored to the unique needs of mothers in the postpartum period. Ultimately, this study aims to improve the overall well-being of new mothers and promote optimal maternal health during the postpartum journey.

Keywords: maternal mental health, postpartum distress, postpartum depression, postnatal mothers

Procedia PDF Downloads 39

Authors: Fenni Sim

Abstract:

Background: The application of systemic family therapy approaches to community health cases have not gathered traction. In National Kidney Foundation, Singapore, the belief is that community support has great potential in helping End Stage Renal Failure (ESRF) patients manage the demands of their treatment regime, whether Hemodialysis (HD) or Peritoneal Dialysis(PD) and sustain them on the treatment. However, the current community support does not include family interventions and is largely nursing based. Although nursing support is well provided to patients, and their family members in issues related to treatment and compliance, complex family issues and dynamics arising from caregiver strain or pre-dialysis relationship strain might deter efforts in managing the challenges of the treatment. Objective: The objective of the study is to understand the potential scope of work provided by a social worker who is trained in systemic family therapy and the effects of these interventions. Methodology: 3 families on HD and 3 families on PD who have been receiving family intervention for the past 6 months would be chosen for the study. A qualitative interview would be conducted to review the effectiveness for the family. Scales such as SCORE-15, PHQ-9, and Zarit Burden were used to measure family functioning, depression, and caregiver’s burden for the families. Results: The research is still in preliminary phase. Conclusion: The study highlights the importance of family intervention for families with multiple stressors on different treatment modalities who might have different needs and challenges. Nursing support needs to be complemented with family-based support to manage complex family issues in order to achieve better health outcomes and improved family coping.

Keywords: complementing nursing support, end stage renal failure, healthcare, systemic approaches

Procedia PDF Downloads 186

Authors: Ingrid van der Heijden, Kristen Dunkle, Rachel Jewkes

Abstract:

Background: Emerging literature on prevalence shows that men with disabilities are four more times likely than men without disabilities to experience sexual violence during their lifetime. However, compared to women with disabilities, men with disabilities still have lesser experiences of violence. While empirical evidence on the prevalence of victimization of men with disabilities is emerging, there is scarcer evidence highlighting disabled men’s perpetration of different forms of violence, particularly intimate partner violence. We can assume that men are likely to be both perpetrators and victims of violence, making more complex the causes and risks of violence. Gender norms and disability stigma play important roles in men’s experiences of violence. Men may be stigmatized because of their inability to attain hegemonic masculine ideals of strength, control over women and sexual conquest, which makes them more susceptible to emotional, physical and sexual abuse. Little to no evidence exists of men with disabilities’ experiences of perpetration of intimate partner violence, family violence or community violence. So far studies on male victimization do not succeed to offer contextual evidence that would highlight why and how men with disabilities perpetrate and/or are victims of sexual or other forms of violence. Objective: The overall aim to highlight men with disabilities’ experiences of both victimization and perpetration, and how living up to normative and hegemonic ideals of masculinity and ‘ability’ shape their experiences. It will include: identifying how gender and impairments intersect and shape their experiences of violence; identifying the contexts of and risks for violence; identifying the impacts and consequences of violence on their lives (including mental health impacts), and identifying obstacles and enablers to support and interventions to prevent violence. Methodology: In-depth qualitative interviews with 20 men with disabilities participating in interventions conducted by the What Works Global Programme for violence prevention (DIFD) in Africa and Asia. Men with a range of disabilities will be invited to share their lifetime experiences of violence. Implications for Practice: The data from this study will be used to start thinking about strategies to include men with disabilities in violence prevention strategies for both men and women. Limitations: Because men will be participating in interventions, it is assumed that they will not have severe impairments that hamper their cognitive or physical ability to participate in the intervention activities - and therefore will be able to participate in the in-depth interviews. Of course, this is a limitation of the study as it does not include those men with severe disabilities – measured by the World Health Organization’s International Classification of Functioning - who may be more vulnerable and at higher risk of experiencing violence, and who are less likely to be able to access services and interventions.

Keywords: gender, men with disabilities, perpetration of violence, victimization

Procedia PDF Downloads 307