Search results for: chlorophyll content monitoring

Authors: Nicholas Mavrogiannis, Francesca Crivellari, Zachary Gagnon

Abstract:

Development of low-cost, rapid, sensitive and portable biosensing systems are important for the detection and prevention of disease in developing countries, biowarfare/antiterrorism applications, environmental monitoring, point-of-care diagnostic testing and for basic biological research. Currently, the most established commercially available and widespread assays for portable point of care detection and disease testing are paper-based dipstick and lateral flow test strips. These paper-based devices are often small, cheap and simple to operate. The last three decades in particular have seen an emergence in these assays in diagnostic settings for detection of pregnancy, HIV/AIDS, blood glucose, Influenza, urinary protein, cardiovascular disease, respiratory infections and blood chemistries. Such assays are widely available largely because they are inexpensive, lightweight, and portable, are simple to operate, and a few platforms are capable of multiplexed detection for a small number of sample targets. However, there is a critical need for sensitive, quantitative and multiplexed detection capabilities for point-of-care diagnostics and for the detection and prevention of disease in the developing world that cannot be satisfied by current state-of-the-art paper-based assays. For example, applications including the detection of cardiac and cancer biomarkers and biothreat applications require sensitive multiplexed detection of analytes in the nM and pM range, and cannot currently be satisfied with current inexpensive portable platforms due to their lack of sensitivity, quantitative capabilities and often unreliable performance. In this talk, inexpensive label-free biomolecular detection at liquid interfaces using a newly discovered electrokinetic phenomenon known as fluidic dielectrophoresis (fDEP) is demonstrated. The electrokinetic approach involves exploiting the electrical mismatches between two aqueous liquid streams forced to flow side-by-side in a microfluidic T-channel. In this system, one fluid stream is engineered to have a higher conductivity relative to its neighbor which has a higher permittivity. When a “low” frequency (< 1 MHz) alternating current (AC) electrical field is applied normal to this fluidic electrical interface the fluid stream with high conductivity displaces into the low conductive stream. Conversely, when a “high” frequency (20MHz) AC electric field is applied, the high permittivity stream deflects across the microfluidic channel. There is, however, a critical frequency sensitive to the electrical differences between each fluid phase – the fDEP crossover frequency – between these two events where no fluid deflection is observed, and the interface remains fixed when exposed to an external field. To perform biomolecular detection, two streams flow side-by-side in a microfluidic T-channel: one fluid stream with an analyte of choice and an adjacent stream with a specific receptor to the chosen target. The two fluid streams merge and the fDEP crossover frequency is measured at different axial positions down the resulting liquid

Keywords: biodetection, fluidic dielectrophoresis, interfacial polarization, liquid interface

Procedia PDF Downloads 448

Authors: Desmond Appiah, Fan Zhang, Shouqi Yuan, Wei Xueyuan, Stephen N. Asomani

Abstract:

The side channel pump has distinctive hydraulic performance characteristics over other vane pumps because of its generation of high pressure heads in only one impeller revolution. Hence, there is soaring utilization and application in the fields of petrochemical, food processing fields, automotive and aerospace fuel pumping where high heads are required at low flows. The side channel pump is characterized by unstable flow because after fluid flows into the impeller passage, it moves into the side channel and comes back to the impeller again and then moves to the next circulation. Consequently, the flow leaves the side channel pump following a helical path. However, the pressure fluctuation exhibited in the flow greatly contributes to the unwanted noise and vibration which is associated with the flow. In this paper, a side channel pump prototype was examined thoroughly through numerical calculations based on SST k-ω turbulence model to ascertain the pressure fluctuation behavior. The pressure fluctuation intensity of the 3D unstable flow dynamics were carefully investigated under different working conditions 0.8QBEP, 1.0 QBEP and 1.2QBEP. The results showed that the pressure fluctuation distribution around the pressure side of the blade is greater than the suction side at the impeller and side channel interface (z=0) for all three operating conditions. Part-load condition 0.8QBEP recorded the highest pressure fluctuation distribution because of the high circulation velocity thus causing an intense exchanged flow between the impeller and side channel. Time and frequency domains spectra of the pressure fluctuation patterns in the impeller and the side channel were also analyzed under the best efficiency point value, QBEP using the solution from the numerical calculations. It was observed from the time-domain analysis that the pressure fluctuation characteristics in the impeller flow passage increased steadily until the flow reached the interrupter which separates low-pressure at the inflow from high pressure at the outflow. The pressure fluctuation amplitudes in the frequency domain spectrum at the different monitoring points depicted a gentle decreasing trend of the pressure amplitudes which was common among the operating conditions. The frequency domain also revealed that the main excitation frequencies occurred at 600Hz, 1200Hz, and 1800Hz and continued in the integers of the rotating shaft frequency. Also, the mass flow exchange plots indicated that the side channel pump is characterized with many vortex flows. Operating conditions 0.8QBEP, 1.0 QBEP depicted less and similar vortex flow while 1.2Q recorded many vortex flows around the inflow, middle and outflow regions. The results of the numerical calculations were finally verified experimentally. The performance characteristics curves from the simulated results showed that 0.8QBEP working condition recorded a head increase of 43.03% and efficiency decrease of 6.73% compared to 1.0QBEP. It can be concluded that for industrial applications where the high heads are mostly required, the side channel pump can be designed to operate at part-load conditions. This paper can serve as a source of information in order to optimize a reliable performance and widen the applications of the side channel pumps.

Keywords: exchanged flow, pressure fluctuation, numerical simulation, side channel pump

Procedia PDF Downloads 138

Authors: Nataliya G. Olkhovik

Abstract:

Nowadays in the system of Russian higher medical education there have been undertaken initiatives that resulted in focusing on the resources of e-learning in teaching foreign languages. Obviously, the face-to-face communication in foreign languages bears much more advantages in terms of effectiveness in comparison with the potential of e-learning. Thus, we’ve faced the necessity of strengthening the capacity of e-learning via integration of active methods into the process of teaching foreign languages, such as project activity of students. Successful project activity of students should involve the following components: monitoring, control, methods of organizing the student’s activity in foreign languages, stimulating their interest in the chosen project, approaches to self-assessment and methods of raising their self-esteem. The contemporary methodology assumes the project as a specific method, which activates potential of a student’s cognitive function, emotional reaction, ability to work in the team, commitment, skills of cooperation and, consequently, their readiness to verbalize ideas, thoughts and attitudes. Verbal activity in the foreign language is a complex conception that consolidates both cognitive (involving speech) capacity and individual traits and attitudes such as initiative, empathy, devotion, responsibility etc. Once we organize the project activity by the means of e-learning within the ‘Foreign language’ discipline we have to take into consideration all mentioned above characteristics and work out an effective way to implement it into the teaching practice to boost its educational potential. We have integrated into the e-platform Moodle the module of project activity consisting of the following blocks of tasks that lead students to research, cooperate, strive to leadership, chase the goal and finally verbalize their intentions. Firstly, we introduce the project through activating self-activity of students by the tasks of the phase ‘Preparation of the project’: choose the topic and justify it; find out the problematic situation and its components; set the goals; create your team, choose the leader, distribute the roles in your team; make a written report on grounding the validity of your choices. Secondly, in the ‘Planning the project’ phase we ask students to represent the analysis of the problem in terms of reasons, ways and methods of solution and define the structure of their project (here students may choose oral or written presentation by drawing up the claim in the e-platform about their wish, whereas the teacher decides what form of presentation to prefer). Thirdly, the students have to design the visual aids, speech samples (functional phrases, introductory words, keywords, synonyms, opposites, attributive constructions) and then after checking, discussing and correcting with a teacher via the means of Moodle present it in front of the audience. And finally, we introduce the phase of self-reflection that aims to awake the inner desire of students to improve their verbal activity in a foreign language. As a result, by implementing the project activity into the e-platform and project activity, we try to widen the frameworks of a traditional lesson of foreign languages through tapping the potential of personal traits and attitudes of students.

Keywords: active methods, e-learning, improving verbal activity in foreign languages, personal traits and attitudes

Procedia PDF Downloads 109

Authors: Aashutosh Garg, Ankur Rajpal, A. A. Kazmi

Abstract:

The efficiency of an on-site wastewater treatment system named Johkasou was evaluated based on its pollutant removal efficiency over 10 months. This system was installed at IIT Roorkee and had a capacity of treating 7 m3/d of sewage water, sufficient for a group of 30-50 people. This system was fed with actual wastewater through an equalization tank to eliminate the fluctuations throughout the day. Methanol and ammonium chloride was added into this equalization tank to increase the Chemical Oxygen Demand (COD) and ammonia content of the influent. The outlet from Johkasou is sent to a tertiary unit consisting of a Pressure Sand Filter and an Activated Carbon Filter for further treatment. Samples were collected on alternate days from Monday to Friday and the following parameters were evaluated: Chemical Oxygen Demand (COD), Biochemical Oxygen Demand (BOD), Total Suspended Solids (TSS), and Total Nitrogen (TN). The Average removal efficiency for Chemical Oxygen Demand (COD), Biochemical Oxygen Demand (BOD), Total Suspended Solids (TSS), and Total Nitrogen (TN) was observed as 89.6, 97.7, 96, and 80% respectively. The cost of treating the wastewater comes out to be Rs 23/m3 which includes electricity, cleaning and maintenance, chemical, and desludging costs. Tests for the coliforms were also performed and it was observed that the removal efficiency for total and fecal coliforms was 100%. The sludge generation rate is approximately 20% of the BOD removal and it needed to be removed twice a year. It also showed a very good response against the hydraulic shock load. We performed vacation stress analysis on the system to evaluate the performance of the system when there is no influent for 8 consecutive days. From the result of stress analysis, we concluded that system needs a recovery time of about 48 hours to stabilize. After about 2 days, the system returns again to original conditions and all the parameters in the effluent become within the limits of National Green Tribunal (NGT) standards. We also performed another stress analysis to save the electricity in which we turned the main aeration blower off for 2 to 12 hrs a day and the results showed that we can turn the blower off for about 4-6 hrs a day and this will help in reducing the electricity costs by about 25%. It was concluded that the Johkasou system can remove a sufficient amount of all the physiochemical parameters tested to satisfy the prescribed limit set as per Indian Standard.

Keywords: on-site treatment, domestic wastewater, Johkasou, nutrient removal, pathogens removal

Procedia PDF Downloads 120

Authors: A. U. Ugwu

Abstract:

Post-Apartheid South African education system had witnessed waves of curriculum reforms. Accordingly, there have been evidences of responsiveness towards local and global challenges of sustainable development over the past decade. In other words, the curriculum shows sensitivity towards issues of Sustainable Development (SD). Moreover, the paradigm of Sustainable Development Goals (SDGs) was introduced by the UNESCO in year 2015. The SDGs paradigm is essentially a vision towards actualizing sustainability in all aspects of the global society. Education for Sustainable Development (ESD) in retrospect entails teaching and learning to actualize the intended UNESCO 2030 SDGs. This paper explores how teaching and learning of ESD can be improved, by drawing from local context of the South African schooling system. Preservice natural sciences and technology teachers in their 2nd to 4th years of study at a university’s college of education in South Africa were contacted as participants of the study. Using qualitative case study research design, the study drew from the views and experiences of five (5) purposively selected participants from a broader study, aiming to closely understating how ESD is implemented pedagogically in teaching and learning. The inquiry employed questionnaires and a focus group discussion as qualitative data generation tools. A qualitative data analysis of generated data was carried out using content and thematic analysis, underpinned by interpretive paradigm. The result of analyzed data, suggests that ESD pedagogy at the location where this research was conducted is largely influenced by contextual factors. Furthermore, the result of the study shows that there is a critical need to employ/adopt local experiences or occurrences while teaching sustainable development. Certain pedagogical approaches such as the use of videos relative to local context should also be considered in order to achieve a more realistic application. The paper recommends that educational institutions through teaching and learning should implement ESD by drawing on local contexts and problems, thereby foregrounding constructivism, appreciating and fostering students' prior knowledge and lived experiences.

Keywords: context, education for sustainable development, natural sciences and technology preservice teachers, qualitative research, sustainable development goals

Procedia PDF Downloads 171

Authors: A. Kalizhanova, T. Shelestova

Abstract:

Teacher professional development (TPD) in Kazakhstan has followed a fairly standard format for centuries, with teachers learning new information from a lecturer and being tested using multiple-choice questions. In the online world, self-access courses have become increasingly popular. Due to their extensive multimedia content, peer-reviewed assignments, adaptable class times, and instruction from top university faculty from across the world, massive open online courses (MOOCs) have found a home in Kazakhstan's system for lifelong learning. Recent studies indicate the limited use of connectivism-based tools such as discussion forums by Kazakhstani pre-service and in-service English teachers, whose professional interests are limited to obtaining certificates rather than enhancing their teaching abilities and exchanging knowledge with colleagues. This paper highlights the significance of connectivism-based tools and instruments, such as MOOCs, for the continuous professional development of pre- and in-service English teachers, facilitators' roles, and their strategies for enhancing trainees' conceptual knowledge within the MOOCs' curriculum and online learning skills. Reviewing the most pertinent papers on Connectivism Theory, facilitators' function in TPD, and connectivism-based tools, such as MOOCs, a code extraction method was utilized. Three experts, former active participants in a series of projects initiated across Kazakhstan to improve the efficacy of MOOCs, evaluated the excerpts and selected the most appropriate ones to propose the matrix of teacher professional competencies that can be acquired through MOOCs. In this paper, we'll look at some of the strategies employed by course instructors to boost their students' English skills and knowledge of course material, both inside and outside of the MOOC platform. Participants' interactive learning contributed to their language and subject conceptual knowledge and prepared them for peer-reviewed assignments in the MOOCs, and this approach of small group interaction was given to highlight the outcomes of participants' interactive learning. Both formal and informal continuing education institutions can use the findings of this study to support teachers in gaining experience with MOOCs and creating their own online courses.

Keywords: connectivism-based tools, teacher professional development, massive open online courses, facilitators, Kazakhstani context

Procedia PDF Downloads 86

Authors: Berengere Vire, Nicolas Salvetat, Yoann Lannay, Guillaume Marcellin, Siem Van Der Laan, Franck Molina, Dinah Weissmann

Abstract:

Predicting suicidal behaviors is one of the most complex challenges of daily psychiatric practices. Today, suicide risk prediction using biological tools is not validated and is only based on subjective clinical reports of the at-risk individual. Therefore, there is a great need to identify biomarkers that would allow early identification of individuals at risk of suicide. Alterations of adenosine-to-inosine (A-to-I) RNA editing of neurotransmitter receptors and other proteins have been shown to be involved in etiology of different psychiatric disorders and linked to suicidal behavior. RNA editing is a co- or post-transcriptional process leading to a site-specific alteration in RNA sequences. It plays an important role in the epi transcriptomic regulation of RNA metabolism. On postmortem human brain tissue (prefrontal cortex) of depressed suicide victims, Alcediag found specific alterations of RNA editing activity on the mRNA coding for the serotonin 2C receptor (5-HT2cR). Additionally, an increase in expression levels of ADARs, the RNA editing enzymes, and modifications of RNA editing profiles of prime targets, such as phosphodiesterase 8A (PDE8A) mRNA, have also been observed. Interestingly, the PDE8A gene is located on chromosome 15q25.3, a genomic region that has recurrently been associated with the early-onset major depressive disorder (MDD). In the current study, we examined whether modifications in RNA editing profile of prime targets allow identifying disease-relevant blood biomarkers and evaluating suicide risk in patients. To address this question, we performed a clinical study to identify an RNA editing signature in blood of depressed patients with and without the history of suicide attempts. Patient’s samples were drawn in PAXgene tubes and analyzed on Alcediag’s proprietary RNA editing platform using next generation sequencing technology. In addition, gene expression analysis by quantitative PCR was performed. We generated a multivariate algorithm comprising various selected biomarkers to detect patients with a high risk to attempt suicide. We evaluated the diagnostic performance using the relative proportion of PDE8A mRNA editing at different sites and/or isoforms as well as the expression of PDE8A and the ADARs. The significance of these biomarkers for suicidality was evaluated using the area under the receiver-operating characteristic curve (AUC). The generated algorithm comprising the biomarkers was found to have strong diagnostic performances with high specificity and sensitivity. In conclusion, we developed tools to measure disease-specific biomarkers in blood samples of patients for identifying individuals at the greatest risk for future suicide attempts. This technology not only fosters patient management but is also suitable to predict the risk of drug-induced psychiatric side effects such as iatrogenic increase of suicidal ideas/behaviors.

Keywords: blood biomarker, next-generation-sequencing, RNA editing, suicide

Procedia PDF Downloads 262

Authors: Caroline Selai, Sushrut Jadhav

Abstract:

Background: University College London (UCL), the first secular university in England to admit students regardless of their religion and gender, has nearly 29,000 students of which approximately 30% are international students. The UCL Cultural Consultation Service (CCS) for staff and students is a unique service that provides assistance to staff and students experiencing challenges in their teaching, enabling, support work or studies which they believe may have a cultural component. The service provides one-to-one and group consultations, lectures, seminars, ‘grand rounds’, interactive workshops and bespoke interventions. Data: This paper presents a content analysis of CCS referrals over the last 36 months. We focus on the experience of international students, many of whom experience not only a challenge to their academic identity but also a profound challenge to their personal cultural identity. We also present 3 vignettes to illustrate how students interpret, accept, contest and resist changes in their cultural and academic identity. Discussion: This paper highlights (i) how students from collectivist cultures attempt to assimilate within an individualistic, highly competitive western university that is bound by its own institutional norms; (ii) problems in negotiating challenges at the interface of culture and gender (iii) the impact of culturally different hierarchies of power, discrimination and authority and (iv) the significance of earlier traumatic and kinship conflicts. Many international students’ social identities are shaped by their cultural and family scripts. A large number have been taught that their teachers are to be revered and their teachings unchallenged. This is at odds with quintessential goal of the western university to encourage healthy scepticism and hone students’ critical thinking skills. Conclusions: Pupil-teacher ‘cultural transference’ and shifts in cultural academic identities of students underscore critical aspects of developmental and learning challenges for students. Staff-student cultural conflict requires a broader, systemic analysis of students, staff and the wider organisation. Our findings challenge Eurocentric psychodynamic concepts such as the nature of parent-child relationship in Western Europe. We argue for a broader, more inclusive approach to develop both effective pedagogic skills in euro-american academic institutions and culturally- appropriate psychodynamic theory to underpin counselling international students.

Keywords: academic identity, cultural transference, cultural consultation in higher education, cultural formulation, cultural identity.

Procedia PDF Downloads 463

Authors: C. Virgilio, J. Carlier, P. Campistron, M. Toubal, P. Garnier, L. Broussous, V. Thomy, B. Nongaillard

Abstract:

Wetting efficiency of microstructures or nanostructures patterned on Si wafers is a real challenge in integrated circuits manufacturing. In fact, bad or non-uniform wetting during wet processes limits chemical reactions and can lead to non-complete etching or cleaning inside the patterns and device defectivity. This issue is more and more important with the transistors size shrinkage and concerns mainly high aspect ratio structures. Deep Trench Isolation (DTI) structures enabling pixels’ isolation in imaging devices are subject to this phenomenon. While low-frequency acoustic reflectometry principle is a well-known method for Non Destructive Test applications, we have recently shown that it is also well suited for nanostructures wetting characterization in a higher frequency range. In this paper, we present a high-frequency acoustic reflectometry characterization of DTI wetting through a confrontation of both experimental and modeling results. The acoustic method proposed is based on the evaluation of the reflection of a longitudinal acoustic wave generated by a 100 µm diameter ZnO piezoelectric transducer sputtered on the silicon wafer backside using MEMS technologies. The transducers have been fabricated to work at 5 GHz corresponding to a wavelength of 1.7 µm in silicon. The DTI studied structures, manufactured on the wafer frontside, are crossing trenches of 200 nm wide and 4 µm deep (aspect ratio of 20) etched into a Si wafer frontside. In that case, the acoustic signal reflection occurs at the bottom and at the top of the DTI enabling its characterization by monitoring the electrical reflection coefficient of the transducer. A Finite Difference Time Domain (FDTD) model has been developed to predict the behavior of the emitted wave. The model shows that the separation of the reflected echoes (top and bottom of the DTI) from different acoustic modes is possible at 5 Ghz. A good correspondence between experimental and theoretical signals is observed. The model enables the identification of the different acoustic modes. The evaluation of DTI wetting is then performed by focusing on the first reflected echo obtained through the reflection at Si bottom interface, where wetting efficiency is crucial. The reflection coefficient is measured with different water / ethanol mixtures (tunable surface tension) deposited on the wafer frontside. Two cases are studied: with and without PFTS hydrophobic treatment. In the untreated surface case, acoustic reflection coefficient values with water show that liquid imbibition is partial. In the treated surface case, the acoustic reflection is total with water (no liquid in DTI). The impalement of the liquid occurs for a specific surface tension but it is still partial for pure ethanol. DTI bottom shape and local pattern collapse of the trenches can explain these incomplete wetting phenomena. This high-frequency acoustic method sensitivity coupled with a FDTD propagative model thus enables the local determination of the wetting state of a liquid on real structures. Partial wetting states for non-hydrophobic surfaces or low surface tension liquids are then detectable with this method.

Keywords: wetting, acoustic reflectometry, gigahertz, semiconductor

Procedia PDF Downloads 328

Authors: Sikiru O. Aminu, Magda Ismail Abdul Mohsin, Fauziah M. Taib

Abstract:

Fund collections for Waqf projects in some Muslim countries received some boost because of the resuscitation of the cash waqf concept This study envisages that such development can improve the economic empowerment of the poor in contemporary Muslim communities given appropriate collections and effective management of the Waqf institution. Recent developments in the Financial Technology (FINTECH) space portend valuable relevance in the conduct and delivery of social charitable causes such as Waqf around the world. Particularly, emerging areas in FINTECH such as Islamic Crowdfunding (ICF) and blockchain have brought about greater efficiency and effectiveness through cost reduction, faster transactions, wider access, transparency and prompt disclosure of adequate information to relevant stakeholders. These FINTECH options of ICF and blockchain provide veritable opportunities to resuscitate, re-align, synergize and magnify the Islamic Social Finance (ISF) ecosystem of Waqf, Zakat and Sodaqah to generate positive and sustainable impact to the community, environment and the economy at large, with a view to projecting the Maqasid Shari’ah (Objective of the Law Giver). To document the effect of FINTECH on Waqf, this study examined the activities of six banks in Malaysia that signed a pact to utilize FINTECH for waqf collection towards improving the economy. Semi-structured Face to Face interviews were conducted with officers in charge of Waqf in the six banks, founder of the Islamic Crowdfunding platform and senior officers in Waqaf Selangor. Content analysis was used to analyze their responses, and the emergent themes were reported verbatim. Based on the derived themes, survey questionnaires were also administered to 300 customers with respect to the Waqf’s FINTECH functionalities of the identified banks.to further confirm and strengthen the results of the interviews. Simple descriptive analysis was performed on the result of the survey questionnaire to provide clear information on the questions raised. The findings showed a disproportionate level of readiness among the banks, where few of the banks have put structure in place to increase their Waqf collections, others are at their elementary stage. However, the commitment is high across the six banks to achieve their set goals.

Keywords: blockchain, Fintech, Islamic crowdfunding, waqf

Procedia PDF Downloads 174

Authors: A. De Serres-Lafontaine, S. Porlier, K. Poitras

Abstract:

Introduction: Placement is, without doubt, a challenging experience for both foster children and biological parents who witness their child being removed from their care. Yet, few studies have examined parenting in such a context through critical parental skills such as parental sensitivity and commitment. Sensitivity is described as the capacity of parents to respond accurately to their child’s needs in a warm, predictable and consistent way, whereas commitment is the ability of the parent to get involved physically and emotionally in an enduring relationship with his child. The research confirms the important role of parental sensitivity and parental commitment on child development following placement in foster care. Nevertheless, these studies were mainly conducted with foster parents, and few studies have examined these components of parenthood with biological parents. Method: This study evolves in two times. At first, 17 parents participated throughout a 90-minutes interview. It allowed to collect information regarding the sociodemographic situation, contacts, placement trajectory. Parental sensitivity is observed during a supervised parent-child contact. The second time occurred one to two years later and implied an at-home 90-minutes interview where we updated the information from the first interview and were able to assess the level of parental commitment. In this ongoing part of the study, five parents have already participated in implying the rest of them remain to be interviewed in the coming months - from October through December 2018. Results: Descriptive analysis from the first part of the study suggests the examination of two groups: 11 children have been reunified whereas six are still in foster care. Qualitative analysis allows to compare themes of sensitivity and commitment regarding if the reunification project occurs or not. Preliminary analysis about thematic content shows key components of parental commitment through parent’s reveal of the way they nurture a relationship with their child. Furthermore, preliminary analysis suggests that parental sensitivity is not associated with family reunification (r = 0,11, p = 0,74). Further analysis will be assessed with the date from the second part of the study to examine the potential association between commitment and reunification. Discussion: Parental sensitivity and commitment are fundamental to the well-being of the child in a placement trajectory. They need to be understood better as two different complex concepts and as two parenting skills that might have a way of echoing to one another when engaged in a specific context. Above all, a more accurate comprehension of parenting in a placement trajectory allows to sustain adequate intervention practices for birth parents and could change the way parental adequacy is assessed when reaching for reunification.

Keywords: child welfare, foster care, intervention practices, parenthood

Procedia PDF Downloads 184

Authors: W. L. Tsang, H. Y. Li, S. L. Wong, T. Y. Kwok, S. C. Yuen, S. S. Kwok, P. S. Ko, S. Y. Lau

Abstract:

Introduction: Palliative care is no doubt necessary in surgery. When one looks at studies of what patients with life-threatening illness want and compares to what they experience in surgical units, the gap is huge. Surgical nurses, being patient advocates, should engage with patients and families sooner rather than later in their illness trajectories to consider how to manage the illness, not just their capacity to survive. Objective: This clinical practice guide aims to fill the service gap of palliative care in surgery by producing a quality-driven, evidence-based yet straightforward clinical practice guide based on a focus strategy. Methodology: In line with Guide to Good Nursing Practice: End-of-Life Care recommended by Nursing Council of Hong Kong and the strategic goal of improving quality of palliative care proposed in HA Strategic Plan 2017-2022, multiple phases of work were undertaken from July 2015 to December 2017. A pragmatic clinical practice guide for surgical patients facing life-threatening conditions was developed based on assessments on knowledge of and attitudes towards end-of-life care of surgical nurses. Key domains, including preparation for bereavement, nursing care for imminently dying patients and at the dying scene were crystallized according to the results of the assessments and the palliative care checklist formulated by UCH Palliative Care Team. After a year of rollout, its content was refined through analyses of implementation in routine practice and consensus opinions from frontline nurses. Results and Outcomes: This clinical practice guide inspires surgical nurses with the art of care to provide for patients’ comfort, function, and longevity. It provides practical directions and assists nurses to master the skills on advance care planning and learn how to be clear with patients, families and themselves about the realities of the disease pictures. Through the implementation, patients and families are included in the decision process, and their wishes are honored. The delivery of explicit and high-quality palliative care maintains good nurse-to-patient relations and enhances satisfaction of hospital care of patients and families. Conclusion: Surgical nursing has always been up to the unique challenges of the era. This clinical practice guide has become an island of credibility for our nurses as they traverse the often stormy waters of life-limiting illness.

Keywords: palliative care delivery, palliative care in surgery, hospice care, end-of-life care

Procedia PDF Downloads 259

Authors: Wipakon Sonsnam, Kanya Napapongsa

Abstract:

The quantitative aim of the study; 1) health conditions, to examine the state of health of the aging, 2) perceived of self-efficacy, self-care of aging ,3) perceived of social support of the aging, 4) to examine factors associated with self-efficacy in enhancing the health and self-care when illness. 100 samples selected from communities in Dusit, Bangkok, 2014 by random sampling. The questionnaires were used to collect data have 5-point rating scale, consisting of strongly agree, agree, undecided, disagree, and strongly disagree; approved content valid by 3 experts, reliability coefficients alpha was .784 for perceived of self-efficacy, self-care of aging and .827 for perceived of social support of the aging. ST-5, 2Q used for collect mental health. The ability to engage in a daily routine was collected by Barthel ADL index. Founding, the sample group were female (68%). (33%) of them were in the age of 60-65. Most of them were married and still live with their spouse (55%) and do not work (38%). The average annual income was less than 10,000 baht supported by child. Most people think that income was adequate (49.0%) and Satisfaction (61.0%). Most of aging caring them-self, followed by them spouse (26%). Welfare of the public had supported, living for the aging (100%), followed by Join and health volunteers in communities (23%). In terms of health, (53%) of the sample group feels health was fair, hypertension was the most common health condition among sample group (68%), following by diabetes (55%). About eyesight, (42%) have visual acuity. (59.0%) do not need hearing aids. 84% have more than 20 teeth remaining, and have no problem with chewing (61%). In terms of Ability to engage in a daily routine, most of people (84%) in sample group are in type 1. (91%) of the participants don’t have bladder incontinence. For mental condition, (82%) do not have insomnia. (87%) do not have anxiety. (96%) do not have depression. However, (77%) of the sample group is facing stress. In terms of environment in home, bathroom in the home (90.0%) and floor of bathroom was slippery (91.0%). (48%) of the sample group has the skills of how to look after themselves while being sick, and how to keep up healthy lifestyle. Besides, some other factors, such as gender, age and educational background are related to the health perception. The statistical significance was <0.05. Suggestion: The instruments available to national standards such as ST-5, 2Q and Barthel ADL index. Reliability coefficients alpha was .784 for perceived of self-efficacy, self-care of aging and .827 for perceived of social support of the aging. The instrument used to collect perceived of social support must be further developed to study level of influence of social support that affect the health of elderly.

Keywords: ้health status, perception of aging, self-efficacy, social support

Procedia PDF Downloads 546

Authors: Alexandra Tucaliuc, Alexandra C. Blaga, Anca I. Galaction, Lenuta Kloetzer, Dan Cascaval

Abstract:

Ergosterol (ergosta-5,7,22-trien-3β-ol), also known as provitamin D2, is the precursor of vitamin D2 (ergocalciferol), because it is converted under UV radiation to this vitamin. The natural sources of ergosterol are mainly the yeasts (Saccharomyces sp., Candida sp.), but it can be also found in fungus (Claviceps sp.) or plants (orchids). In the yeasts cells, ergosterol is accumulated in membranes, especially in free form in the plasma membrane, but also as esters with fatty acids in membrane lipids. The chemical synthesis of ergosterol does not represent an efficient method for its production, in these circumstances, the most attractive alternative for producing ergosterol at larger-scale remains the aerobic fermentation using S. cerevisiae on glucose or by-products from agriculture of food industry as substrates, in batch or fed-batch operating systems. The aim of this work is to analyze comparatively the influence of aeration efficiency on ergosterol production by S. cerevisiae in batch and fed-batch fermentations, by considering different levels of mixing intensity, aeration rate, and n-dodecane concentration. The effects of the studied factors are quantitatively described by means of the mathematical correlations proposed for each of the two fermentation systems, valid both for the absence and presence of oxygen-vector inside the broth. The experiments were carried out in a laboratory stirred bioreactor, provided with computer-controlled and recorded parameters. n-Dodecane was used as oxygen-vector and the ergosterol content inside the yeasts cells has been considered at the fermentation moment related to the maximum concentration of ergosterol, 9 hrs for batch process and 20 hrs for fed-batch one. Ergosterol biosynthesis is strongly dependent on the dissolved oxygen concentration. The hydrocarbon concentration exhibits a significant influence on ergosterol production mainly by accelerating the oxygen transfer rate. Regardless of n-dodecane addition, by maintaining the glucose concentration at a constant level in the fed-batch process, the amount of ergosterol accumulated into the yeasts cells has been almost tripled. In the presence of hydrocarbon, the ergosterol concentration increased by over 50%. The value of oxygen-vector concentration corresponding to the maximum level of ergosterol depends mainly on biomass concentration, due to its negative influences on broth viscosity and interfacial phenomena of air bubbles blockage through the adsorption of hydrocarbon droplets–yeast cells associations. Therefore, for the batch process, the maximum ergosterol amount was reached for 5% vol. n-dodecane, while for the fed-batch process for 10% vol. hydrocarbon.

Keywords: bioreactors, ergosterol, fermentation, oxygen-vector

Procedia PDF Downloads 191

Authors: A. Chávez, A. Rodríguez, F. Pinzón

Abstract:

Society is concerned about measures of environmental, economic and social impacts generated in the solid waste disposal. These places of confinement, also known as landfills, are locations where problems of pollution and damage to human health are reduced. They are technically designed and operated, using engineering principles, storing the residue in a small area, compact it to reduce volume and covering them with soil layers. Problems preventing liquid (leachate) and gases produced by the decomposition of organic matter. Despite planning and site selection for disposal, monitoring and control of selected processes, remains the dilemma of the leachate as extreme concentration of pollutants, devastating soil, flora and fauna; aggressive processes requiring priority attention. A biological technology is the activated sludge system, used for tributaries with high pollutant loads. Since transforms biodegradable dissolved and particulate matter into CO2, H2O and sludge; transform suspended and no Settleable solids; change nutrients as nitrogen and phosphorous; and degrades heavy metals. The microorganisms that remove organic matter in the processes are in generally facultative heterotrophic bacteria, forming heterogeneous populations. Is possible to find unicellular fungi, algae, protozoa and rotifers, that process the organic carbon source and oxygen, as well as the nitrogen and phosphorus because are vital for cell synthesis. The mixture of the substrate, in this case sludge leachate, molasses and wastewater is maintained ventilated by mechanical aeration diffusers. Considering as the biological processes work to remove dissolved material (< 45 microns), generating biomass, easily obtained by decantation processes. The design consists of an artificial support and aeration pumps, favoring develop microorganisms (denitrifying) using oxygen (O) with nitrate, resulting in nitrogen (N) in the gas phase. Thus, avoiding negative effects of the presence of ammonia or phosphorus. Overall the activated sludge system includes about 8 hours of hydraulic retention time, which does not prevent the demand for nitrification, which occurs on average in a value of MLSS 3,000 mg/L. The extended aeration works with times greater than 24 hours detention; with ratio of organic load/biomass inventory under 0.1; and average stay time (sludge age) more than 8 days. This project developed a pilot system with sludge leachate from Doña Juana landfill - RSDJ –, located in Bogota, Colombia, where they will be subjected to a process of activated sludge and extended aeration through a sequential Bach reactor - SBR, to be dump in hydric sources, avoiding ecological collapse. The system worked with a dwell time of 8 days, 30 L capacity, mainly by removing values of BOD and COD above 90%, with initial data of 1720 mg/L and 6500 mg/L respectively. Motivating the deliberate nitrification is expected to be possible commercial use diffused aeration systems for sludge leachate from landfills.

Keywords: sludge, landfill, leachate, SBR

Procedia PDF Downloads 279

Authors: Ashleigh Hillier, Jody Goldstein, Lauren Tornatore, Emily Byrne

Abstract:

As individuals with disabilities attend higher education in greater numbers, universities are seeking ways to support the retention and success of these students, beyond the academically based accommodations. Although mentoring programs for this population are being implemented more frequently, there is a lack of empirically validated outcomes which could promote program replication. The research objective of this exploratory study was to examine outcomes for students with disabilities participating in a peer-to-peer mentoring program. Mentees (students with disabilities) met with their mentor (trained upperclassman) once a week for an hour for one semester (14-weeks). Mentors followed a curriculum structured by monthly and weekly goals to guide the sessions. Curriculum topics included socializing on campus, peer pressure, time management, communicating with peers and professors, classroom etiquette, study skills, and seeking help and campus resources. Data was collected over a period of seven semesters resulting in seven separate cohorts (n=46). The impact of the program was measured using quantitative self-report measures as well as qualitative content analysis of focus groups. Academic outcomes (retention, credits earned, and GPA) were compared between those in the mentoring program and a matched group of students registered with Disability Services who did not receive mentoring. In addition, a one-year follow up was conducted to examine the longer term impact of participation. Findings indicated that mentoring had the most impact in knowing how things work at the university, knowing how and where to find opportunities to meet people on campus, and knowing how to access supports. Mentors also provided a supportive relationship to the mentees and helped with social skills. There were no significant differences in academic outcomes between those who were mentored and those in the comparison group. Most mentees reported continuing to benefit from the program one year on, providing support for the retention of knowledge gained and maintenance of positive outcomes over time. In conclusion, while a range of positive outcomes were evidenced, the model was limited in its impact more broadly, particularly with regards to academic success and impacting more complex challenges.

Keywords: mentor, outcomes, students with disabilities, university

Procedia PDF Downloads 148

Authors: Anu Chandran, Reena Esther Rani

Abstract:

Background of the Study: Dotted with multiple Unique Destination Prepositions (UDPs), Tamil Nadu is an established tourism brand as regards leisure, MICE, culture, and ecological flavors. Albeit, the enchanting destination possesses distinctive attributes and resources yet to be tapped for better competitive advantage. Being a destination that allures an incredible variety of migratory birds, Tamil Nadu is deemed to be an ornithologist’s paradise. This study primarily explores the prospects of developing Kaliveli, recognized as a bird sanctuary in the Tindivanam forest division of the Villupuram district in the State. Kaliveli is an ideal nesting site for migratory birds and is currently apt for a prospective analysis of regenerative tourism. Objectives of the study: This research lays an accent on avian tourism as part and parcel of sustainable tourism ventures. The impacts of projects like the Ornithological Conservation Centre on tourists have been gauged in the present paper. It maps the futuristic proactive propositions linked to regenerative tourism on the site. How far technological innovations can do a world of good in Kaliveli through Artificial Intelligence, Smart Tourism, and similar latest coinages to entice real eco-tourists, have been conceptualized. The experiential dimensions of resource stewardship as regards facilitating tourists’ relish the offerings in a sustainable manner is at the crux of this work. Methodology: Modeled as a case study, this work tries to deliberate on the impact of existing projects attributed to avian fauna in Kalveli. Conducted in the qualitative research design mode, the case study method was adopted for the processing and presentation of study results drawn by applying thematic content analysis based on the data collected from the field. Result and discussion: One of the key findings relates to the kind of nature trails that can be a regenerative dynamic for eco-friendly tourism in Kaliveli. Field visits have been conducted to assess the niche tourism aspects which could be incorporated with the regenerative tourism model to be framed as part of the study.

Keywords: regenerative tourism, Kaliveli bird sanctuary, sustainable development, resource Stewardship, Ornithology, Avian Fauna

Procedia PDF Downloads 84

Authors: Emma R. Arakelova, Stepan G. Grigoryan, Flora G. Arsenyan, Nelli S. Babayan, Ruzanna M. Grigoryan, Natalia K. Sarkisyan

Abstract:

Novel nanosize zinc oxide composites of doxorubicin obtained by deposition of 180 nm thick zinc oxide film on the drug surface using DC-magnetron sputtering of a zinc target in the form of gels (PEO+Dox+ZnO and Starch+NaCMC+Dox+ZnO) were studied for drug delivery applications. The cancer specificity was revealed both in in vitro and in vivo models. The cytotoxicity of the test compounds was analyzed against human cancer (HeLa) and normal (MRC5) cell lines using MTT colorimetric cell viability assay. IC50 values were determined and compared to reveal the cancer specificity of the test samples. The mechanistic study of the most active compound was investigated using Flow cytometry analyzing of the DNA content after PI (propidium iodide) staining. Data were analyzed with Tree Star FlowJo software using cell cycle analysis Dean-Jett-Fox module. The in vivo anticancer activity estimation experiments were carried out on mice with inoculated ascitic Ehrlich’s carcinoma at intraperitoneal introduction of doxorubicin and its zinc oxide compositions. It was shown that the nanosize zinc oxide film deposition on the drug surface leads to the selective anticancer activity of composites at the cellular level with the range of selectivity index (SI) from 4 (Starch+NaCMC+Dox+ZnO) to 200 (PEO(gel)+Dox+ZnO) which is higher than that of free Dox (SI = 56). The significant increase in vivo antitumor activity (by a factor of 2-2.5) and decrease of general toxicity of zinc oxide compositions of doxorubicin in the form of the above mentioned gels compared to free doxorubicin were shown on the model of inoculated Ehrlich's ascitic carcinoma. Mechanistic studies of anticancer activity revealed the cytostatic effect based on the high level of DNA biosynthesis inhibition at considerable low concentrations of zinc oxide compositions of doxorubicin. The results of studies in vitro and in vivo behavior of PEO+Dox+ZnO and Starch+NaCMC+Dox+ZnO composites confirm the high potential of the nanosize zinc oxide composites as a vector delivery system for future application in cancer chemotherapy.

Keywords: anticancer activity, cancer specificity, doxorubicin, zinc oxide

Procedia PDF Downloads 416

Authors: Ashraf Nawaz Khan, R. Alagirusamy, Apurba Das, Puneet Mahajan

Abstract:

The thermoplastic-based fibre composites are acquiring a market sector of conventional as well as thermoset composites. However, replacing the thermoset with a thermoplastic composite has never been an easy task. The inherent high viscosity of thermoplastic resin reveals poor interface properties. In this work, a homo-polymer towpreg is produced through an electrostatic powder spray coating methodology. The produced flexible towpreg offers a low melt-flow distance during the consolidation of the laminate. The reduced melt-flow distance demonstrates a homogeneous fibre/matrix distribution (and low void content) on consolidation. The composite laminate has been fabricated with two manufacturing techniques such as conventional film stack (FS) and powder-coated (PC) technique. This helps in understanding the distinct response of produced laminates on applying load since the laminates produced through the two techniques are comprised of the same constituent fibre and matrix (constant fibre volume fraction). The changed behaviour is observed mainly due to the different fibre/matrix configurations within the laminate. The interface adhesion influences the load transfer between the fibre and matrix. Therefore, it influences the elastic, plastic, and failure patterns of the laminates. Moreover, the effect of preform geometries (plain weave and satin weave structure) are also studied for corresponding composite laminates in terms of various mechanical properties. The fracture analysis is carried out to study the effect of resin at the interlacement points through micro-CT analysis. The PC laminate reveals a considerably small matrix-rich and deficient zone in comparison to the FS laminate. The different load tensile, shear, fracture toughness, and drop weight impact test) is applied to the laminates, and corresponding damage behaviour is analysed in the successive stage of failure. The PC composite has shown superior mechanical properties in comparison to the FS composite. The damage that occurs in the laminate is captured through the SEM analysis to identify the prominent mode of failure, such as matrix cracking, fibre breakage, delamination, debonding, and other phenomena.

Keywords: composite, damage, fibre, manufacturing

Procedia PDF Downloads 139

Authors: Stephanie Yun Yu Law

Abstract:

Background: This study aims to investigate into communication between trainee doctors and patients, especially how doctor’s reaction to patient’s emotional issues expressed in the consultation affect patient’s satisfaction. Objectives: Thus, there are three aims in this study, 1.) how do trainee doctors react to patients emotional cues in OSCE station? 2.) Any differences in the respond type to emotional cues between first year students and third year students? 3.) Is response type (reducing space) related to OSCE outcome (patient satisfaction and expert rating)? Methods: Fifteen OSCE stations was videotaped, in which 9 were stations with first-year students and 6 were with third-year students. OSCE outcomes were measured by Communication Assessment Tool and Examiners Checklist. Analyses: All patient’s cues/concerns and student’s reaction were coded by Verona Coding Definitions of Emotional Sequence. Descriptive data was gathered from Observer XT and logistic regression (two-level) was carried out to see if occurrence of reducing space response can be predicted by OSCE outcomes. Results: Reducing space responses from all students were slightly less than a half in total responses to patient’s cues. The mean percentage of reducing space behaviours was lower among first year students when compared to third year students. Patient’s satisfaction significantly (p<0.05) and negatively predicted reducing space behaviours. Conclusions: Most of the medical students, to some extent, did not provide adequate responses for patient’s emotional cues. But first year students did provide more space for patients to talk about their emotional issues when compared to third year students. Lastly, patients would feel less satisfied if trainee doctors use more reducing space responses in reaction to patient’s expressed emotional cues/concerns. Practical implications: Firstly, medical training programme can be tailored on teaching students how to detect and respond appropriately to emotional cues in order to improve underperformed student’s communication skills in healthcare setting. Furthermore, trainee doctor’s relationship with patients in clinical practice can also be improved by reacting appropriately to patient’s emotive cues in consultations (such as limit the use of reducing space behaviours).

Keywords: doctors-patients communication, applied clinical psychology, health psychology, healthcare professionals

Procedia PDF Downloads 220

Authors: Berfu Guley Goren, Ayse Lale Berkoz

Abstract:

The aim of the study is to analyze the concept of universal design and accessibility to make the city which allows equality and independence for individuals. In the content of the study, literature researches and observations of samples in Istanbul, Turkey are analyzed. As a result proposals are going to be developed to create the cities which are designed for everyone. In globalization process, in cities, population have been increasing dramatically with social and economic activities. Medical developments have been effective in prolonging human life and the disability that comes with aging has also increased in parallel with the disabled population. Nowadays disability is an important phenomenon. Because approximately 1 billion people live with disabilities. The heterogeneous structure formed by the rapid gathering of individuals with different social, economic and physical characteristics in the cities creates great spatial diversity and richness in the cities with different needs brought together. Unlike the cultural and physical wealth in these places and the potential to integrate and diversify the urban people, unfortunately, the designs in practice cause the urban areas to break apart, the urbanities to tear themselves apart, to interfere with their communication and interactions. The social and physical structure of the city is important to feel belonging to the urban society. In most cities when an observation is made, obstructions for people with disabilities can be seen in urban physical structure and design. With these obstructions, people with disabilities cannot live in urban space, and they are desolated in urban life. The city, which offers equal opportunity, the relation between economic development, social justice and built environment must be planned synchronous. Isolation and stigmatization must be abolished by regulations, activities of awareness and universal urban design. Without regard to social, economical and physical features every individual has the same right, which is using the freedom of movement. Supporting freedom of movement of every individual may be ensured by universal design and its principles. So urban spaces are going to be for every individual. For equal opportunity in urban services, urban design must be the focus on every individual including people with disabilities. In built environment practices, democratic suitable spaces should be created. In this respect, urban planners, architects, political decision-makers and other relevant actors should work together and should think very versatile.

Keywords: disability, equality, universal design, urban design

Procedia PDF Downloads 308

Authors: Mathew O. Ayoola, Foluke Aderemi, Tunde E. Lawal, Opeyemi Oladejo, Micheal A. Abiola

Abstract:

Food animals reared for meat require transportation during their life cycle. The transportation procedures could initiate stressors capable of disrupting the physiological homeostasis. Such stressors associated with transportation may include; loading and unloading, crowding, environmental temperature, fear, vehicle motion/vibration, feed / water deprivation, and length of travel. This may cause oxidative stress and damage to excess free radicals or reactive oxygen species (ROS). In recent years, the application of natural products as a substitute for synthetic electrolytes and tranquilizers as anti-stress agents during the transportation is yet under investigation. Sweet orange, a predominant fruit in humid tropics, has been reported to have a good content of vitamin C (Ascorbic acid). Vitamin C, which is an active ingredient in orange juice, plays a major role in the biosynthesis of Corticosterone, a hormone that enhances energy supply during transportation and heat stress. Ninety-six, 15weeks, Isa brown pullets were allotted to four (4) oral treatments; sterile water (T1), synthetic vit C (T2), 30ml orange/liter of water (T3), 50ml orange/1 liter (T4). Physiological parameters; body temperature (BTC), rectal temperature (RTC), respiratory rate (RR), and panting rate (PR) were measured pre and post-transportation. The birds were transported with a specialized vehicle for a distance of 50km at a speed of 60 km/hr. The average environmental THI and within the vehicle was 81.8 and 74.6, respectively, and the average wind speed was 11km/hr. Treatments and periods had a significant (p>0.05) effect on all the physiological parameters investigated. Birds on T1 are significantly (p<0.05) different as compared to T2, T3, and T4. Values recorded post-transportation are significantly (p<0.05) higher as compared to pre-transportation for all parameters. In conclusion, this study showed that transportation as a stressor can affect the physiological homeostasis of pullets. Oral supplementation of electrolytes or tranquilizers is essential as an anti-stress during transportation. The application of the organic product in form of sweet orange could serve as a suitable alternative for the synthetic vitamin C.

Keywords: physiological, pullets, sweet orange, transportation stress, and vitamin C

Procedia PDF Downloads 123

Authors: Lotanna Ezeonu, Jason P. Robbins, Ziyu Tang, Xiaofang Yang, Bruce E. Koel, Simon G. Podkolzin

Abstract:

The interaction of organic molecules with metal surfaces is of interest in numerous technological applications, such as catalysis, bone replacement, and biosensors. Acetic acid is one of the main products of bio-oils produced from the pyrolysis of hemicellulosic feedstocks. However, their high oxygen content makes them unsuitable for use as fuels. Hydrodeoxygenation is a proven technique for catalytic deoxygenation of bio-oils. An understanding of the energetics and control of the bond-breaking sequences of biomass-derived oxygenates on metal surfaces will enable a guided optimization of existing catalysts and the development of more active/selective processes for biomass transformations to fuels. Such investigations have been carried out with the aid of ultrahigh vacuum and its concomitant techniques. The high catalytic activity of platinum in biomass-derived oxygenate transformations has sparked a lot of interest. We herein exploit infrared reflection absorption spectroscopy(IRAS), temperature-programmed desorption(TPD), and density functional theory(DFT) to study the adsorption and decomposition of acetic acid on a Pt(111) surface, which was then compared with Ni(111), a model non-noble metal. We found that acetic acid adsorbs molecularly on the Pt(111) surface, interacting through the lone pair of electrons of one oxygen atomat 90 K. At 140 K, the molecular form is still predominant, with some dissociative adsorption (in the form of acetate and hydrogen). Annealing to 193 K led to complete dehydrogenation of molecular acetic acid species leaving adsorbed acetate. At 440 K, decomposition of the acetate species occurs via decarbonylation and decarboxylation as evidenced by desorption peaks for H₂,CO, CO₂ and CHX fragments (x=1, 2) in theTPD.The assignments for the experimental IR peaks were made using visualization of the DFT-calculated vibrational modes. The results showed that acetate adsorbs in a bridged bidentate (μ²η²(O,O)) configuration. The coexistence of linear and bridge bonded CO was also predicted by the DFT results. Similar molecular acid adsorption energy was predicted in the case of Ni(111) whereas a significant difference was found for acetate adsorption.

Keywords: acetic acid, platinum, nickel, infared-absorption spectrocopy, temperature programmed desorption, density functional theory

Procedia PDF Downloads 113

Authors: Shamie Kumar

Abstract:

Background: Radiologists and radiographers (RR) need to educate themselves and their colleagues to ensure that AI is integrated safely, useful, and in a meaningful way with the direction it always benefits the patients. AI education and training are fundamental to the way RR work and interact with it, such that they feel confident using it as part of their clinical practice in a way they understand it. Methodology: This exploratory research will outline the current educational and training gaps for radiographers and radiologists in AI radiology diagnostics. It will review the status, skills, challenges of educating and teaching. Understanding the use of artificial intelligence within daily clinical practice, why it is fundamental, and justification on why learning about AI is essential for wider adoption. Results: The current knowledge among RR is very sparse, country dependent, and with radiologists being the majority of the end-users for AI, their targeted training and learning AI opportunities surpass the ones available to radiographers. There are many papers that suggest there is a lack of knowledge, understanding, and training of AI in radiology amongst RR, and because of this, they are unable to comprehend exactly how AI works, integrates, benefits of using it, and its limitations. There is an indication they wish to receive specific training; however, both professions need to actively engage in learning about it and develop the skills that enable them to effectively use it. There is expected variability amongst the profession on their degree of commitment to AI as most don’t understand its value; this only adds to the need to train and educate RR. Currently, there is little AI teaching in either undergraduate or postgraduate study programs, and it is not readily available. In addition to this, there are other training programs, courses, workshops, and seminars available; most of these are short and one session rather than a continuation of learning which cover a basic understanding of AI and peripheral topics such as ethics, legal, and potential of AI. There appears to be an obvious gap between the content of what the training program offers and what the RR needs and wants to learn. Due to this, there is a risk of ineffective learning outcomes and attendees feeling a lack of clarity and depth of understanding of the practicality of using AI in a clinical environment. Conclusion: Education, training, and courses need to have defined learning outcomes with relevant concepts, ensuring theory and practice are taught as a continuation of the learning process based on use cases specific to a clinical working environment. Undergraduate and postgraduate courses should be developed robustly, ensuring the delivery of it is with expertise within that field; in addition, training and other programs should be delivered as a way of continued professional development and aligned with accredited institutions for a degree of quality assurance.

Keywords: artificial intelligence, training, radiology, education, learning

Procedia PDF Downloads 90

Authors: Patrick Louie Robles, Jerry Suls, Ciaran Friel, Mark Butler, Samantha Gordon, Frank Vicari, Joan Duer-Hefele, Karina W. Davidson

Abstract:

Physical activity guidelines focus on increasing moderate-intensity activity for older adults, but adherence to recommendations remains low. This is despite the fact that scientific evidence finds increasing physical activity is positively associated with health benefits. Behavior change techniques (BCTs) have demonstrated some effectiveness in reducing sedentary behavior and promoting physical activity. This pilot study uses a personalized trials (N-of-1) design, delivered virtually, to evaluate the efficacy of using five BCTs in increasing low-intensity physical activity (by 2,000 steps of walking per day) in adults aged 45-75 years old. The 5 BCTs described in habit formation theory are goal setting, action planning, rehearsal, rehearsal in a consistent context, and self-monitoring. The study recruited health system employees in the target age range who had no mobility restrictions and expressed interest in increasing their daily activity by a minimum of 2,000 steps per day at least five days per week. Participants were sent a Fitbit Charge 4 fitness tracker with an established study account and password. Participants were recommended to wear the Fitbit device 24/7 but were required to wear it for a minimum of ten hours per day. Baseline physical activity was measured by Fitbit for two weeks. Participants then engaged remotely with a clinical research coordinator to establish a “walking plan” that included a time and day interval (e.g., between 7am -8am on Monday-Friday), a location for the walk (e.g., park), and how much time the plan would need to achieve a minimum of 2,000 steps over their baseline average step count (20 minutes). All elements of the walking plan were required to remain consistent throughout the study. In the 10-week intervention phase of the study, participants received all five BCTs in a single, time-sensitive text message. The text message was delivered 30 minutes prior to the established walk time and signaled participants to begin walking when the context (i.e., day of the week, time of day) they pre-selected is encountered. Participants were asked to log both the start and conclusion of their activity session by pressing a button on the Fitbit tracker. Within 30 minutes of the planned conclusion of the activity session, participants received a text message with a link to a secure survey. Here, they noted whether they engaged in the BCTs when prompted and completed an automaticity survey to identify how “automatic” their walking behavior had become. At the end of their trial, participants received a personalized summary of their step data over time, helping them learn more about their responses to the five BCTs. Whether the use of these 5 ‘habit formation’ BCTs in combination elicits a change in physical activity behavior among older adults will be reported. This study will inform the feasibility of a virtually-delivered N-of-1 study design to effectively promote physical activity as a component of healthy aging.

Keywords: aging, exercise, habit, walking

Procedia PDF Downloads 143

Authors: Ambika Perisamy, Asyriawati binte Mohd Hamzah

Abstract:

The focus of this presentation is to discuss teacher professional development (TPD) through the use of technology. TPD is necessary to prepare teachers for future challenges they will face throughout their careers and to develop new skills and good teaching practices. We will also be discussing current issues in embracing technology in the field of early childhood education and the impact on the professional development of teachers. Participants will also learn to apply teaching and learning practices through the use of technology. One major objective of this presentation is to coherently fuse practical, technology and theoretical content. The process begins by concretizing a set of preconceived ideas which need to be joined with theoretical justifications found in the literature. Technology can make observations fairer and more reliable, easier to implement, and more preferable to teachers and principals. Technology will also help principals to improve classroom observations of teachers and ultimately improve teachers’ continuous professional development. Video technology allows the early childhood teachers to record and keep the recorded video for reflection at any time. This will also provide opportunities for her to share with her principals for professional dialogues and continuous professional development plans. A total of 10 early childhood teachers and 4 principals were involved in these efforts which identified and analyze the gaps in the quality of classroom observations and its co relation to developing teachers as reflective practitioners. The methodology used involves active exploration with video technology recordings, conversations, interviews and authentic teacher child interactions which forms the key thrust in improving teaching and learning practice. A qualitative analysis of photographs, videos, transcripts which illustrates teacher’s reflections and classroom observation checklists before and after the use of video technology were adopted. Arguably, although PD support can be magnanimously strong, if teachers could not connect or create meaning out of the opportunities made available to them, they may remain passive or uninvolved. Therefore, teachers must see the value of applying new ideas such as technology and approaches to practice while creating personal meaning out of professional development. These video recordings are transferable, can be shared and edited through social media, emails and common storage between teachers and principals. To conclude the importance of reflective practice among early childhood teachers and addressing the concerns raised before and after the use of video technology, teachers and principals shared the feasibility, practical and relevance use of video technology.

Keywords: early childhood education, reflective, improve teaching and learning, technology

Procedia PDF Downloads 506

Authors: Petra Hypšová, Martin Seitl

Abstract:

One of the challenges of forensic psychology is to detect deception during a face-to-face interview. In addition to the classical approaches of monitoring the utterance and its components, detection is also sought by observing behavioral and physiological changes that occur as a result of the increased emotional and cognitive load caused by the production of distorted information. Typical are changes in facial temperature, eye movements and their fixation, pupil dilation, emotional micro-expression, heart rate and its variability. Expanding technological capabilities have opened the space to detect these psychophysiological changes and behavioral manifestations through non-contact technologies that do not interfere with face-to-face interaction. Non-contact deception detection methodology is still in development, and there is a lack of studies that combine multiple non-contact technologies to investigate their accuracy, as well as studies that show how different types of lies produced by different interviewers affect physiological and behavioral changes. The main objective of this study is to apply a specific non-contact technology for deception detection. The next objective is to investigate scenarios in which non-contact deception detection is possible. A series of psychophysiological experiments using infrared thermal imaging, eye tracking and behavioral analysis with FaceReader 9.0 software was used to achieve our goals. In the laboratory experiment, 16 adults (12 women, 4 men) between 18 and 35 years of age (SD = 4.42) were instructed to produce alternating prepared and spontaneous truths and lies. The baseline of each proband was also measured, and its results were compared to the experimental conditions. Because the personality of the examiner (particularly gender and facial appearance) to whom the subject is lying can influence physiological and behavioral changes, the experiment included four different interviewers. The interviewer was represented by a photograph of a face that met the required parameters in terms of gender and facial appearance (i.e., interviewer likability/antipathy) to follow standardized procedures. The subject provided all information to the simulated interviewer. During follow-up analyzes, facial temperature (main ROIs: forehead, cheeks, the tip of the nose, chin, and corners of the eyes), heart rate, emotional expression, intensity and fixation of eye movements and pupil dilation were observed. The results showed that the variables studied varied with respect to the production of prepared truths and lies versus the production of spontaneous truths and lies, as well as the variability of the simulated interviewer. The results also supported the assumption of variability in physiological and behavioural values during the subject's resting state, the so-called baseline, and the production of prepared and spontaneous truths and lies. A series of psychophysiological experiments provided evidence of variability in the areas of interest in the production of truths and lies to different interviewers. The combination of technologies used also led to a comprehensive assessment of the physiological and behavioral changes associated with false and true statements. The study presented here opens the space for further research in the field of lie detection with non-contact technologies.

Keywords: emotional expression decoding, eye-tracking, functional infrared thermal imaging, non-contact deception detection, psychophysiological experiment

Procedia PDF Downloads 102

Authors: Petros Dlamini, Bethiweli Malambo, Maggie Masenya

Abstract:

Knowledge management practices are very important in public libraries, especial in the era of the information society. The success of public libraries depends on the recognition and application of knowledge management practices. The study investigates the value and challenges of knowledge management practices in public libraries. Three research objectives informed the study: to identify knowledge management practices in public libraries, understand the value of knowledge management practices in public libraries, and determine the factors hampering knowledge management practices in public libraries. The study was informed by the interpretivism research paradigm, which is associated with qualitative studies. In that light, the study collected data from eight librarians and or library heads, who were purposively selected from public libraries. The study adopted a social anthropological approach, which thoroughly evaluated each participant's response. Data was collected from the respondents through telephonic semi-structured interviews and assessed accordingly. Furthermore, the study used the latest content concept for data interpretation. The chosen data analysis method allowed the study to achieve its main purpose with concrete and valid information. The study's findings showed that all six (100%) selected public libraries apply knowledge management practices. The findings of the study revealed that public libraries have knowledge sharing as the main knowledge management practice. It was noted that public libraries employ many practices, but each library employed its practices of choice depending on their knowledge management practices structure. The findings further showed that knowledge management practices in public libraries are employed through meetings, training, information sessions, and awareness, to mention a few. The findings revealed that knowledge management practices make the libraries usable. Furthermore, it has been asserted that knowledge management practices in public libraries meet users’ needs and expectations and equip them with skills. It was discovered that all participating public libraries from Umkhanyakude district municipality valued their knowledge management practices as the pillar and foundation of services. Noticeably, knowledge management practices improve users ‘standard of living and build an information society. The findings of the study showed that librarians should be responsible for the value of knowledge management practices as they are qualified personnel. The results also showed that 83.35% of public libraries had factors hampering knowledge management practices. The factors are not limited to shortage of funds, resources and space, and political interference. Several suggestions were made to improve knowledge management practices in public libraries. These suggestions include improving the library budget, increasing libraries’ building sizes, and conducting more staff training.

Keywords: knowledge management, knowledge management practices, storage, dissemination

Procedia PDF Downloads 99

Authors: Chen Wang, Jared Evans, Yan Asmann

Abstract:

With the quick evolvement of next-generation sequencing techniques, whole-exome or exome-panel data have become a cost-effective way for detection of small exonic mutations, but there has been a growing desire to accurately detect copy number variations (CNVs) as well. In order to address this research and clinical needs, we developed a sequencing coverage pattern-based method not only for copy number detections, data integrity checks, CNV calling, and visualization reports. The developed methodologies include complete automation to increase usability, genome content-coverage bias correction, CNV segmentation, data quality reports, and publication quality images. Automatic identification and removal of poor quality outlier samples were made automatically. Multiple experimental batches were routinely detected and further reduced for a clean subset of samples before analysis. Algorithm improvements were also made to improve somatic CNV detection as well as germline CNV detection in trio family. Additionally, a set of utilities was included to facilitate users for producing CNV plots in focused genes of interest. We demonstrate the somatic CNV enhancements by accurately detecting CNVs in whole exome-wide data from the cancer genome atlas cancer samples and a lymphoma case study with paired tumor and normal samples. We also showed our efficient reuses of existing exome sequencing data, for improved germline CNV calling in a family of the trio from the phase-III study of 1000 Genome to detect CNVs with various modes of inheritance. The performance of the developed method is evaluated by comparing CNV calling results with results from other orthogonal copy number platforms. Through our case studies, reuses of exome sequencing data for calling CNVs have several noticeable functionalities, including a better quality control for exome sequencing data, improved joint analysis with single nucleotide variant calls, and novel genomic discovery of under-utilized existing whole exome and custom exome panel data.

Keywords: bioinformatics, computational genetics, copy number variations, data reuse, exome sequencing, next generation sequencing

Procedia PDF Downloads 260

Authors: Lesly Y Carmona-Sarabia, Luisa Barraza-Vergara, Vilmalí López-Mejías, Wandaliz Torres-García, Maribella Domenech-Garcia, Madeline Torres-Lugo

Abstract:

Biosensors are used in many applications providing real-time monitoring to treat long-term conditions. Thus, understanding the physicochemical properties and biological side effects on the skin of polymers (e. g., poly(methyl methacrylate), PMMA) employed in the fabrication of wearable biosensors is crucial for the selection of manufacturing materials within this field. The PMMA (hydrophobic and thermoplastic polymer) is commonly employed as a coating material or substrate in the fabrication of wearable devices. The cytotoxicityof PMMA (including residual monomers or degradation products) on the skin, in terms of cells and tissue, is required to prevent possible adverse effects (cell death, skin reactions, sensitization) on human health. Within this work, accelerated aging of PMMA (Mw ~ 15000) through thermal and photochemical degradation was under-taken. The accelerated aging of PMMA was carried out by thermal (200°C, 1h) and photochemical degradation (UV-Vis, 8-15d) adapted employing ISO protocols (ISO-10993-12, ISO-4892-1:2016, ISO-877-1:2009, ISO-188: 2011). In addition, in vitro cytotoxicity evaluation of PMMA degradation products was performed using NIH3T3 fibroblast cells to assess the response of skin tissues (in terms of cell viability) exposed with polymers utilized to manufacture wearable biosensors, such as PMMA. The PMMA (Mw ~ 15000) before and after accelerated aging experiments was characterized by thermal gravimetric analysis (TGA), differential scanning calorimetric (DSC), powder X-ray diffractogram (PXRD), and scanning electron microscopy-energy dispersive spectroscopy (SEM-EDS) to determine and verify the successful degradation of this polymer under the specific conditions previously mention. The degradation products were characterized through nuclear magnetic resonance (NMR) to identify possible byproducts generated after the accelerated aging. Results demonstrated a percentage (%) weight loss between 1.5-2.2% (TGA thermographs) for PMMA after accelerated aging. The EDS elemental analysis reveals a 1.32 wt.% loss of carbon for PMMA after thermal degradation. These results might be associated with the amount (%) of PMMA degrade after the accelerated aging experiments. Furthermore, from the thermal degradation products was detected the presence of the monomer and methyl formate (low concentrations) and a low molecular weight radical (·COOCH3) in higher concentrations by NMR. In the photodegradation products, methyl formate was detected in higher concentrations. These results agree with the proposed thermal or photochemical degradation mechanisms found in the literature.1,2 Finally, significant cytotoxicity on the NIH3T3 cells was obtained for the thermal and photochemical degradation products. A decrease in cell viability by > 90% (stock solutions) was observed. It is proposed that the presence of byproducts (e.g. methyl formate or radicals such as ·COOCH₃) from the PMMA degradation might be responsible for the cytotoxicity observed in the NIH3T3 fibroblast cells. Additionally, experiments using skin models will be employed to compare with the NIH3T3 fibroblast cells model.

Keywords: biosensors, polymer, skin irritation, degradation products, cell viability

Procedia PDF Downloads 145