Search results for: optimal solution

Authors: Anders Schou Simonsen, Kim Sorensen, Thomas Condra

Abstract:

Wet scrubbers are used for flue gas desulfurization by injecting water directly into the flue gas stream from a set of sprayers. The water droplets will flow freely inside the scrubber, and flow down along the scrubber walls as a thin wall film while reacting with the gas phase to remove SO₂. This complex multiphase phenomenon can be divided into three main contributions: the continuous gas phase, the liquid droplet phase, and the liquid wall film phase. This study proposes a complete model, where all three main contributions are taken into account and resolved using OpenFOAM for the continuous gas phase, and MATLAB for the liquid droplet and wall film phases. The 3D continuous gas phase is composed of five species: CO₂, H₂O, O₂, SO₂, and N₂, which are resolved along with momentum, energy, and turbulence. Source terms are present for four species, energy and momentum, which are affecting the steady-state solution. The liquid droplet phase experiences breakup, collisions, dynamics, internal chemistry, evaporation and condensation, species mass transfer, energy transfer and wall film interactions. Numerous sub-models have been implemented and coupled to realise the above-mentioned phenomena. The liquid wall film experiences impingement, acceleration, atomization, separation, internal chemistry, evaporation and condensation, species mass transfer, and energy transfer, which have all been resolved using numerous sub-models as well. The continuous gas phase has been coupled with the liquid phases using source terms by an approach, where the two software packages are couples using a link-structure. The complete CFD model has been verified using 16 experimental tests from an existing scrubber installation, where a gradient-based pattern search optimization algorithm has been used to tune numerous model parameters to match the experimental results. The CFD model needed to be fast for evaluation in order to apply this optimization routine, where approximately 1000 simulations were needed. The results show that the complex multiphase phenomena governing wet scrubbers can be resolved in a single model. The optimization routine was able to tune the model to accurately predict the performance of an existing installation. Furthermore, the study shows that a coupling between OpenFOAM and MATLAB is realizable, where the data and source term exchange increases the computational requirements by approximately 5%. This allows for exploiting the benefits of both software programs.

Keywords: desulfurization, discrete phase, scrubber, wall film

Procedia PDF Downloads 264

Authors: Dali Nikolaishvili, Nino Khareba, Mariam Tsitsagi

Abstract:

Tbilisi has been a capital of Georgia since the 5ᵗʰ century. City area was covered by forest in historical past. Nowadays the situation has been changing dramatically. Dozens of problems are caused by damages/destruction of green cover and solution, at one glance, seems to be uncomplicated (planting trees and creating green quarters), but on the other hand, according to the increasing tendency, the built up of areas still remains unsolved. Finding out the ways to overcome such obstacles is important even for protecting the health of society. Making of Retrospective cartography of the forest area of Tbilisi with use of GIS technology and remote sensing was the main aim of the research. Research about the dynamic of forest-cover in Tbilisi and its surroundings included the following steps: assessment of the dynamic of forest in Tbilisi and its surroundings. The survey was mainly based on the retrospective mapping method. Using of GIS technology, studying, comparing and identifying the narrative sources was the next step. And the last one was analyzed of the changes from the 80s to the present days on the basis of decryption of remotely sensed images. After creating a unified cartographic basis, the mapping and plans of different periods have been linked to this geodatabase. Data about green parks, individual old plants existing in the private yards and respondents' Information (according to a questionnaire created in advance) was added to the basic database, the general plan of Tbilisi and Scientific works as well. On the basis of analysis of historic, including cartographic sources, forest-cover maps for different periods of time were made. In addition, was made the catalog of individual green parks (location, area, typical composition, name and so on), which was the basis of creating several thematic maps. Areas with a high rate of green area degradation were identified. Several maps depicting the dynamics of forest cover of Tbilisi were created and analyzed. The methods of linking the data of the old cartographic sources to the modern basis were developed too, the result of which may be used in Urban Planning of Tbilisi. Understanding, perceiving and analyzing the real condition of green cover in Tbilisi and its problems, in turn, will help to take appropriate measures for the maintenance of ancient plants, to develop forests and to plan properly parks, squares, and recreational sites. Because the healthy environment is the main condition of human health and implies to the rational development of the city.

Keywords: catalogue of green area, GIS, historical cartography, cartography, remote sensing, Tbilisi

Procedia PDF Downloads 137

Authors: Parth Gupta, Ujjawal Singh, Shashank Kumar, Mansi Chandra, Arnab Sarkar

Abstract:

Microfluidic devices have emerged as indispensable tools across various scientific disciplines, offering precise control and manipulation of fluids at the microscale. Their efficacy in flow-based research, spanning engineering, chemistry, and biology, relies heavily on the geometric design of microfluidic channels. This work introduces a novel approach to optimise these channels through Response Surface Methodology (RSM), departing from the conventional practice of addressing one parameter at a time. Traditionally, optimising microfluidic channels involved isolated adjustments to individual parameters, limiting the comprehensive understanding of their combined effects. In contrast, our approach considers the simultaneous impact of multiple parameters, employing RSM to efficiently explore the complex design space. The outcome is an innovative microfluidic channel that consumes an optimal sample volume and minimises flow time, enhancing overall efficiency. The relevance of geometric parameter optimization in microfluidic channels extends significantly in biomedical engineering. The flow characteristics of porous materials within these channels depend on many factors, including fluid viscosity, environmental conditions (such as temperature and humidity), and specific design parameters like sample volume, channel width, channel length, and substrate porosity. This intricate interplay directly influences the performance and efficacy of microfluidic devices, which, if not optimized, can lead to increased costs and errors in disease testing and analysis. In the context of biomedical applications, the proposed approach addresses the critical need for precision in fluid flow. it mitigate manufacturing costs associated with trial-and-error methodologies by optimising multiple geometric parameters concurrently. The resulting microfluidic channels offer enhanced performance and contribute to a streamlined, cost-effective process for testing and analyzing diseases. A key highlight of our methodology is its consideration of the interconnected nature of geometric parameters. For instance, the volume of the sample, when optimized alongside channel width, length, and substrate porosity, creates a synergistic effect that minimizes errors and maximizes efficiency. This holistic optimization approach ensures that microfluidic devices operate at their peak performance, delivering reliable results in disease testing. A key highlight of our methodology is its consideration of the interconnected nature of geometric parameters. For instance, the volume of the sample, when optimized alongside channel width, length, and substrate porosity, creates a synergistic effect that minimizes errors and maximizes efficiency. This holistic optimization approach ensures that microfluidic devices operate at their peak performance, delivering reliable results in disease testing. A key highlight of our methodology is its consideration of the interconnected nature of geometric parameters. For instance, the volume of the sample, when optimized alongside channel width, length, and substrate porosity, creates a synergistic effect that minimizes errors and maximizes efficiency. This holistic optimization approach ensures that microfluidic devices operate at their peak performance, delivering reliable results in disease testing.

Keywords: microfluidic device, minitab, statistical optimization, response surface methodology

Procedia PDF Downloads 68

Authors: Sibashish Baksi, Ujjaini Sarkar, Sudeshna Saha

Abstract:

In the present study, hydrolysis of Pinus roxburghi wood powder was carried out with Viscozyme, and kinetics of the hydrolysis has been investigated. Finely ground sawdust is submerged into 2% aqueous peroxide solution (pH=11.5) and pretreated through autoclaving, probe sonication, and alkaline peroxide pretreatment. Afterward, the pretreated material is subjected to hydrolysis. A chain of experiments was executed with delignified biomass (50 g/l) and varying enzyme concentrations (24.2–60.5 g/l). In the present study, 14.32 g/l of glucose, along with 7.35 g/l of xylose, have been recovered with a viscozyme concentration of 48.8 g/l and the same condition was treated as optimum condition. Additionally, thermal deactivation of viscozyme has been investigated and found to be gradually decreasing with escalated enzyme loading from 48.4 g/l (dissociation constant= 0.05 h⁻¹) to 60.5 g/l (dissociation constant= 0.02 h⁻¹). The hydrolysis reaction is a pseudo first-order reaction, and therefore, the rate of the hydrolysis can be expressed as a fractal-like kinetic equation that communicates between the product concentration and hydrolytic time t. It is seen that the value of rate constant (K) increases from 0.008 to 0.017 with augmented enzyme concentration from 24.2 g/l to 60.5 g/l. Greater value of K is associated with stronger enzyme binding capacity of the substrate mass. However, escalated concentration of supplied enzyme ensures improved interaction with more substrate molecules resulting in an enhanced de-polymerization of the polymeric sugar chains per unit time which eventually modifies the physiochemical structure of biomass. All fractal dimensions are in between 0 and 1. Lower the value of fractal dimension, more easily the biomass get hydrolyzed. It can be seen that with increased enzyme concentration from 24.2 g/l to 48.4 g/l, the values of fractal dimension go down from 0.1 to 0.044. This indicates that the presence of more enzyme molecules can more easily hydrolyze the substrate. However, an increased value has been observed with a further increment of enzyme concentration to 60.5g/l because of diffusional limitation. It is evident that the hydrolysis reaction system is a heterogeneous organization, and the product formation rate depends strongly on the enzyme diffusion resistances caused by the rate-limiting structures of the substrate-enzyme complex. Value of the rate constant increases from 1.061 to 2.610 with escalated enzyme concentration from 24.2 to 48.4 g/l. As the rate constant is proportional to Fick’s diffusion coefficient, it can be assumed that with a higher concentration of enzyme, a larger amount of enzyme mass dM diffuses into the substrate through the surface dF per unit time dt. Therefore, a higher rate constant value is associated with a faster diffusion of enzyme into the substrate. Regression analysis of time curves with various enzyme concentrations shows that diffusion resistant constant increases from 0.3 to 0.51 for the first two enzyme concentrations and again decreases with enzyme concentration of 60.5 g/l. During diffusion in a differential scale, the enzyme also experiences a greater resistance during diffusion of larger dM through dF in dt.

Keywords: viscozyme, glucose, fractal kinetics, thermal deactivation

Procedia PDF Downloads 111

Authors: Celine Jaspers

Abstract:

The Belgian legal system is slowly evolving to mandatory mediation to promote ADR. One of the reasons for this evolution is the lack of use of alternative methods in relation to their possible benefits. Especially in divorce cases, ADR can play a beneficial role in resolving disputes, since the emotional component is very much present. When children are involved, a solution provided by the parent may be more adapted to the child’s best interest than a court order. In the first part, the lack of use of voluntary ADR and the evolution toward mandatory ADR in Belgium will be indicated by sources of legislation, jurisprudence and social-scientific sources, with special attention to divorce cases. One of the reasons is lack of knowledge on ADR, despite the continuing efforts of the Belgian legislator to promote ADR. One of the last acts of ADR-promotion, was the implementation of an Act in 2018 which gives the judge the possibility to refer parties to mediation if at least one party wants to during the judicial procedure. This referral is subject to some conditions. The parties will be sent to a private mediator, recognized by the Federal Mediation Commission, to try to resolve their conflict. This means that at least one party can be mandated to try mediation (indicated as “semi-mandatory mediation”). The main goal is to establish the factors and elements that Belgium has to take into account in their further development of mandatory ADR, with consideration of the human rights perspective and the EU perspective. Furthermore it is also essential to detect some dangerous pitfalls other systems have encountered with their process design. Therefore, the second part, the comparative component, will discuss the existing framework in California, USA to establish the necessary elements, possible pitfalls and considerations the Belgian legislator can take into account when further developing the framework of mandatory ADR. The contrasting and functional method will be used to create key elements and possible pitfalls, to help Belgium improve its existing framework. The existing mandatory system in California has been in place since 1981 and is still up and running, and can thus provide valuable lessons and considerations for the Belgian system. Thirdly, the key elements from a human rights perspective and from a European Union perspective (e.g. the right to access to a judge, the right to privacy) will be discussed too, since the basic human rights and European legislation and jurisprudence play a significant part in Belgian legislation as well. The main sources for this part will be the international and European treaties, legislation, jurisprudence and soft law. In the last and concluding part, the paper will list the most important elements of a mandatory ADR-system design with special attention to the dangers of these elements (e.g. to include or exclude domestic violence cases in the mandatory ADR-framework and the consequences thereof), and with special attention for the necessary the international and European rights, prohibitions and guidelines.

Keywords: Belgium, divorce, framework, mandatory ADR

Procedia PDF Downloads 156

Authors: Laura Petrosyan

Abstract:

The high and persistent working results are possible when people are interested in the results of the work. Motivation of working may be present as a psychological complicated phenomena, which determines person's behavior in working process. Researchers point out that working motivation is displayed in three correlated conditions. These are interest in outcomes of work, satisfaction with the work, and the third, is the level of devotion of employee. Solution of the problem of effective staff management depends on the development of workers' skills. Despite, above mentioned problem could be solved by the process of finding methods to induce the employees to the effective work. Motivation of the managerial activity aroused not only during the working process, but also before it starts. During education the future manager obtains many professional skills. However, the experience shows, that only professional skills are not enough for the effective work. Presently, one of the global educational problems is the development of motivation in professions. In psychological literature the fact is mentioned, that the motivation can be inside and outside. Outside motivation is active only at short time. Instead, inside motivation can be active during all process of the professional development. Hence, the motivation of managerial activity might be developed during the education. The future manager choose the profession being under some impression of personal qualities. Detection of future manager’s motivation will influence on the development of syllabuses. Moreover, use of the psychological methods could be evolved for preparing motivated managers. Conducted research has been done in the Public Administration Academy of the RA. The aim of research was to discover students' motivation of profession. 102 master students took part in the research from Public Administration Academy. In the research were used the following methods: method of identifying a person's motivation to succeed (T. Elers) and method of studying students’ motivation (T.E. Ilyin). First of the methods designed to explore a person's motivational orientation to get success represented by Hackhausen. The method gives the opportunity to reveal the level of motivation to success. In the second method separated three scales: i) Knowledge achievements, ii) Knowledge of the profession, iii) Get a diploma. The data obtained from these tests gave quantitative data. Aanalyses of our survey results exposes that within master students the high level have the average rates of knowledge achievements. The average rates of knowledge of the profession and geting a diploma not in high level. Furthermore, there are almost equal to each other. In the educational process The student acquiring skills not synthesize with the wield profession. Results show that specialists really view about profession not formulated yet.

Keywords: managerial activity, motivation, psychological complicated phenomena, working process, education the future manager

Procedia PDF Downloads 448

Authors: Marie Davin, Marie-Laure Fauconnier, Gilles Colinet

Abstract:

In Wallonia, there are 6,000 estimated brownfields (rising to over 3.5 million in Europe) that require remediation. Polycyclic Aromatic Hydrocarbons (PAHs) are a class of recalcitrant carcinogenic/mutagenic organic compounds of major concern as they accumulate in the environment and represent 17% of all encountered pollutants. As an alternative to environmentally aggressive, expensive and often disruptive soil remediation strategies, a lot of research has been directed to developing techniques targeting organic pollutants. The following experiment, based on the observation that PAHs soil content decreases in the presence of plants, aimed at improving our understanding of the underlying mechanisms involved in phytoremediation. It focusses on plant root exudates and whether they improve PAHs solubilization, which would make them more available for bioremediation by soil microorganisms. The effect of saponin, a natural surfactant found in some plant roots such as members of the Fabaceae family, on PAHs solubilization was also investigated as part of the implementation of the experimental protocol. The experiments were conducted on soil collected from a brownfield in Saint-Ghislain (Belgium) and presenting weathered PAHs contamination. Samples of soil were extracted with different solutions containing either plant root exudates or commercial saponin. Extracted PAHs were determined in the different aqueous solutions using High-Performance Liquid Chromatography and Fluorimetric Detection (HPLC-FLD). Both root exudates of alfalfa (Medicago sativa L.) or red clover (Trifolium pratense L.) and commercial saponin were tested in different concentrations. Distilled water was used as a control. First of all, results show that PAHs are more extracted using saponin solutions than distilled water and that the amounts generally rise with the saponin concentration. However, the amount of each extracted compound diminishes as its molecular weight rises. Also, it appears that passed a certain surfactant concentration, PAHs are less extracted. This suggests that saponin might be investigated as a washing agent in polluted soil remediation techniques, either for ex-situ or in-situ treatments, as an alternative to synthetic surfactants. On the other hand, preliminary results on experiments using plant root exudates also show differences in PAHs solubilization compared to the control solution. Further results will allow discussion as to whether or not there are differences according to the exudates provenance and concentrations.

Keywords: brownfield, Medicago sativa, phytoremediation, polycyclic aromatic hydrocarbons, root exudates, saponin, solubilization, Trifolium pratense

Procedia PDF Downloads 253

Authors: Shahram Naghizadeh Raeisi, Ali Alghooneh

Abstract:

The application of whey protein in drink industry to enhance the nutritional value of the products is important. Furthermore, the gelification of protein during thermal treatment and shelf life makes some limitations in its application. So, the main goal of this research is manufacturing of high concentrate whey protein orange drink with appropriate shelf life. In this way, whey protein was 5 to 30% hydrolyzed ( in 5 percent intervals at six stages), then thermal stability of samples with 10% concentration of protein was tested in acidic condition (T= 90 °C, pH=4.2, 5 minutes ) and neutral condition (T=120° C, pH:6.7, 20 minutes.) Furthermore, to study the shelf life of heat treated samples in 4 months at 4 and 24 °C, the time sweep rheological test were done. At neutral conditions, 5 to 20% hydrolyzed sample showed gelling during thermal treatment, whereas at acidic condition, was happened only in 5 to 10 percent hydrolyzed samples. This phenomenon could be related to the difference in hydrodynamic radius and zeta potential of samples with different level of hydrolyzation at acidic and neutral conditions. To study the gelification of heat resistant protein solutions during shelf life, for 4 months with 7 days intervals, the time sweep analysis were performed. Cross over was observed for all heat resistant neutral samples at both storage temperature, while in heat resistant acidic samples with degree of hydrolysis, 25 and 30 percentage at 4 and 20 °C, it was not seen. It could be concluded that the former sample was stable during heat treatment and 4 months storage, which made them a good choice for manufacturing high protein drinks. The Scheffe polynomial model and numerical optimization were employed for modeling and high protein orange drink formula optimization. Scheffe model significantly predicted the overal acceptance index (Pvalue<0.05) of sensorial analysis. The coefficient of determination (R2) of 0.94, the adjusted coefficient of determination (R2Adj) of 0.90, insignificance of the lack-of-fit test and F value of 64.21 showed the accuracy of the model. Moreover, the coefficient of variable (C.V) was 6.8% which suggested the replicability of the experimental data. The desirability function had been achieved to be 0.89, which indicates the high accuracy of optimization. The optimum formulation was found as following: Modified whey protein solution (65.30%), natural orange juice (33.50%), stevia sweetener (0.05%), orange peel oil (0.15%) and citric acid (1 %), respectively. Its worth mentioning that this study made an appropriate model for application of whey protein in drink industry without bitter flavor and gelification during heat treatment and shelf life.

Keywords: croos over, orange beverage, protein modification, optimization

Procedia PDF Downloads 62

Authors: Kanogkan Leerojanaprapa

Abstract:

Textile and garment industry is used to a major exporting industry of Thailand. According to lacking of the nation's price-competitiveness by stopping the EU's GSP (Generalised Scheme of Preferences) and ‘Nationwide Minimum Wage Policy’ that Thailand’s employers must pay all employees at least 300 baht (about $10) a day, the supply chains of the Thai textile and garment industry is affected and need to be reformed. Therefore, either Thai textile or garment industry will be existed or not would be concerned. This is also challenged for the government to decide which industries should be promoted the future industries of Thailand. Recently Thai government launch The Cluster-based Special Economic Development Zones Policy for promoting business cluster (effect on September 16, 2015). They define a cluster as the concentration of interconnected businesses and related institutions that operate within the same geographic areas and textiles and garment is one of target industrial clusters and 9 provinces are targeted (Bangkok, Kanchanaburi, Nakhon Pathom, Ratchaburi, Samut Sakhon, Chonburi, Chachoengsao, Prachinburi, and Sa Kaeo). The cluster zone are defined to link west-east corridor connected to manufacturing source in Cambodia and Mynmar to Bangkok where are promoted to be design, sourcing, and trading hub. The Thai government will provide tax and non-tax incentives for targeted industries within the clusters and expects these businesses are scattered to where they can get the most benefit which will identify future industrial cluster. This research will show the difference between the current cluster and future cluster following the target provinces of the textile and garment. The current cluster is analysed from secondary data. The four characteristics of the numbers of plants in Spinning, weaving and finishing of textiles, Manufacture of made-up textile articles, except apparel, Manufacture of knitted and crocheted fabrics, and Manufacture of other textiles, not elsewhere classified in particular 77 provinces (in total) are clustered by K-means cluster analysis and Hierarchical Cluster Analysis. In addition, the cluster can be confirmed and showed which variables contribute the most to defined cluster solution with ANOVA test. The results of analysis can identify 22 provinces (which the textile or garment plants are located) into 3 clusters. Plants in cluster 1 tend to be large numbers of plants which is only Bangkok, Next plants in cluster 2 tend to be moderate numbers of plants which are Samut Prakan, Samut Sakhon and Nakhon Pathom. Finally plants in cluster 3 tend to be little numbers of plants which are other 18 provinces. The same methodology can be implemented in other industries for future study.

Keywords: ANOVA, hierarchical cluster analysis, industrial clusters, K -means cluster analysis, textile and garment industry

Procedia PDF Downloads 213

Authors: Georgios A. Fragkiadakis, Antonia Psaroudaki, Theodora Mouratidou, Eirini Sfakianaki

Abstract:

Research: Within the project "Actions for the optimal utilization of the potential of carob in the Region of Crete" which is financed-supervised by the Region, with collaboration of Crete University and Hellenic Mediterranean University, a SWOT (strengths, weaknesses, opportunities, threats) survey was carried out, to evaluate the prospects of carob in human nutrition, in Crete. Results and conclusions: 1). Strengths: There exists a local production of carob for human consumption, based on international reports, and local-product reports. The data on products in the market (over 100 brands of carob food), indicates a sufficiency of carob materials offered in Crete. The variety of carob food products retailed in Crete indicates a strong demand-production-consumption trend. There is a stable number (core) of businesses that invest significantly (Creta carob, Cretan mills, etc.). The great majority of the relevant food stores (bakery, confectionary etc.) do offer carob products. The presence of carob products produced in Crete is strong on the internet (over 20 main professionally designed websites). The promotion of the carob food-products is based on their variety and on a few historical elements connected with the Cretan diet. 2). Weaknesses: The international prices for carob seed affect the sector; the seed had an international price of €20 per kg in 2021-22 and fell to €8 in 2022, causing losses to carob traders. The local producers do not sort the carobs they deliver for processing, causing 30-40% losses of the product in the industry. The occasional high price triggers the collection of degraded raw material; large losses may emerge due to the action of insects. There are many carob trees whose fruits are not collected, e.g. in Apokoronas, Chania. The nutritional and commercial value of the wild carob fruits is very low. Carob trees-production is recorded by Greek statistical services as "other cultures" in combination with prickly pear i.e., creating difficulties in retrieving data. The percentage of carob used for human nutrition, in contrast to animal feeding, is not known. The exact imports of carob are not closely monitored. We have no data on the recycling of carob by-products in Crete. 3). Opportunities: The development of a culture of respect for carob trade may improve professional relations in the sector. Monitoring carob market and connecting production with retailing-industry needs may allow better market-stability. Raw material evaluation procedures may be implemented to maintain carob value-chain. The state agricultural services may be further involved in carob-health protection. The education of farmers on carob cultivation/management, can improve the quality of the product. The selection of local productive varieties, may improve the sustainability of the culture. Connecting the consumption of carob with health-food products, may create added value in the sector. The presence and extent of wild carob threes in Crete, represents, potentially, a target for grafting. 4). Threats: The annual fluctuation of carob yield challenges the programming of local food industry activities. Carob is a forest species also - there is danger of wrong classification of crops as forest areas, where land ownership is not clear.

Keywords: human nutrition, carob food, SWOT analysis, crete, greece

Procedia PDF Downloads 92

Authors: M. Tarik Boyraz, M. Bilge Imer

Abstract:

Conventionally cast nickel-based super alloys, such as commercial alloy IN 738 LC, are widely used in manufacturing of industrial gas turbine blades. With carefully designed microstructure and the existence of alloying elements, the blades show improved mechanical properties at high operating temperatures and corrosive environment. The aim of this work is to model and estimate these mechanical properties of IN 738 LC alloy solely based on simulations for projected heat treatment conditions or service conditions. The microstructure (size, fraction and frequency of gamma prime- γ′ and carbide phases in gamma- γ matrix, and grain size) of IN 738 LC needs to be optimized to improve the high temperature mechanical properties by heat treatment process. This process can be performed at different soaking temperature, time and cooling rates. In this work, micro-structural evolution studies were performed experimentally at various heat treatment process conditions, and these findings were used as input for further simulation studies. The operation time, soaking temperature and cooling rate provided by experimental heat treatment procedures were used as micro-structural simulation input. The results of this simulation were compared with the size, fraction and frequency of γ′ and carbide phases, and grain size provided by SEM (EDS module and mapping), EPMA (WDS module) and optical microscope for before and after heat treatment. After iterative comparison of experimental findings and simulations, an offset was determined to fit the real time and theoretical findings. Thereby, it was possible to estimate the final micro-structure without any necessity to carry out the heat treatment experiment. The output of this microstructure simulation based on heat treatment was used as input to estimate yield stress and creep properties. Yield stress was calculated mainly as a function of precipitation, solid solution and grain boundary strengthening contributors in microstructure. Creep rate was calculated as a function of stress, temperature and microstructural factors such as dislocation density, precipitate size, inter-particle spacing of precipitates. The estimated yield stress values were compared with the corresponding experimental hardness and tensile test values. The ability to determine best heat treatment conditions that achieve the desired microstructural and mechanical properties were developed for IN 738 LC based completely on simulations.

Keywords: heat treatment, IN738LC, simulations, super-alloys

Procedia PDF Downloads 248

Authors: Mamert Mbonimpa, Ousseynou Kanteye, Élysée Tshibangu Ngabu, Rachid Amrou, Abdelkabir Maqsoud, Tikou Belem

Abstract:

The management of mine wastes (waste rocks and tailings) containing sulphide minerals such as pyrite and pyrrhotite represents the main environmental challenge for the mining industry. Indeed, acid mine drainage (AMD) can be generated when these wastes are exposed to water and air. AMD is characterized by low pH and high concentrations of heavy metals, which are toxic to plants, animals, and humans. It affects the quality of the ecosystem through water and soil pollution. Different techniques involving soil materials can be used to control AMD generation, including impermeable covers (compacted clays) and oxygen barriers. The latter group includes covers with capillary barrier effects (CCBE), a multilayered cover that include the moisture retention layer playing the role of an oxygen barrier. Once AMD is produced at a mine site, it must be treated so that the final effluent at the mine site complies with regulations and can be discharged into the environment. Active neutralization with lime is one of the treatment methods used. This treatment produces sludge that is usually stored in sedimentation ponds. Other sludge management alternatives have been examined in recent years, including sludge co-disposal with tailings or waste rocks, disposal in underground mine excavations, and storage in technical landfill sites. Considering the ability of AMD neutralization sludge to maintain an alkaline to neutral pH for decades or even centuries, due to the excess alkalinity induced by residual lime within the sludge, valorization of sludge in specific applications could be an interesting management option. If done efficiently, the reuse of sludge could free up storage ponds and thus reduce the environmental impact. It should be noted that mixtures of sludge and soils could potentially constitute usable materials in CCBE for the rehabilitation of acid-generating mine sites, while sludge alone is not suitable for this purpose. The high sludge water content (up to 300%), even after sedimentation, can, however, constitute a geotechnical challenge. Adding lime to the mixtures can reduce the water content and improve the geotechnical properties. The objective of this paper is to investigate the impact of the sludge content (30, 40 and 50%) in sand-sludge mixtures (SSM) on their hydrogeotechnical properties (compaction, shrinkage behaviour, saturated hydraulic conductivity, and water retention curve). The impact of lime addition (dosages from 2% to 6%) on the moisture content, dry density after compaction and saturated hydraulic conductivity of SSM was also investigated. Results showed that sludge adding to sand significantly improves the saturated hydraulic conductivity and water retention capacity, but the shrinkage increased with sludge content. The dry density after compaction of lime-treated SSM increases with the lime dosage but remains lower than the optimal dry density of the untreated mixtures. The saturated hydraulic conductivity of lime-treated SSM after 24 hours of cure decreases by 3 orders of magnitude. Considering the hydrogeotechnical properties obtained with these mixtures, it would be possible to design CCBE whose moisture retention layer is made of SSM. Physical laboratory models confirmed the performance of such CCBE.

Keywords: mine waste, AMD neutralization sludge, sand-sludge mixture, hydrogeotechnical properties, mine site reclamation, CCBE

Procedia PDF Downloads 53

Authors: Mujahid Muhammad, Paul Kearney, Adel Aneiba

Abstract:

The ability for vehicles to communicate with other vehicles (V2V), the physical (V2I) and network (V2N) infrastructures, pedestrians (V2P), etc. – collectively known as V2X (Vehicle to Everything) – will enable a broad and growing set of applications and services within the intelligent transport domain for improving road safety, alleviate traffic congestion and support autonomous driving. The telecommunication research and industry communities and standardization bodies (notably 3GPP) has finally approved in Release 14, cellular communications connectivity to support V2X communication (known as LTE – V2X). LTE – V2X system will combine simultaneous connectivity across existing LTE network infrastructures via LTE-Uu interface and direct device-to-device (D2D) communications. In order for V2X services to function effectively, a robust security mechanism is needed to ensure legal and safe interaction among authenticated V2X entities in the LTE-based V2X architecture. The characteristics of vehicular networks, and the nature of most V2X applications, which involve human safety makes it significant to protect V2X messages from attacks that can result in catastrophically wrong decisions/actions include ones affecting road safety. Attack vectors include impersonation attacks, modification, masquerading, replay, MiM attacks, and Sybil attacks. In this paper, we focus our attention on LTE-based V2X security and access control mechanisms. The current LTE-A security framework provides its own access authentication scheme, the AKA protocol for mutual authentication and other essential cryptographic operations between UEs and the network. V2N systems can leverage this protocol to achieve mutual authentication between vehicles and the mobile core network. However, this protocol experiences technical challenges, such as high signaling overhead, lack of synchronization, handover delay and potential control plane signaling overloads, as well as privacy preservation issues, which cannot satisfy the adequate security requirements for majority of LTE-based V2X services. This paper examines these challenges and points to possible ways by which they can be addressed. One possible solution, is the implementation of the distributed peer-to-peer LTE security mechanism based on the Bitcoin/Namecoin framework, to allow for security operations with minimal overhead cost, which is desirable for V2X services. The proposed architecture can ensure fast, secure and robust V2X services under LTE network while meeting V2X security requirements.

Keywords: authentication, long term evolution, security, vehicle-to-everything

Procedia PDF Downloads 167

Authors: Cynthia K. Burzell

Abstract:

Aequor's Founder, a Marine and Medical Microbiologist, discovered novel, non-toxic chemicals in the ocean that uniquely remove biofilm in minutes and prevent its formation for days. These chemicals and over 70 synthesized analogs that Aequor developed can replace thousands of toxic biocides used in consumer and industrial products and, as new drug candidates, kill biofilm-forming bacteria and fungi Superbugs -the antimicrobial-resistant (AMR) pathogens for which there is no cure. Cynthia Burzell, PhD., is a Marine and Medical Microbiologist studying natural mechanisms that inhibit biofilm formation on surfaces in contact with water. In 2002, she discovered a new genus and several new species of marine microbes that produce small molecules that remove biofilm in minutes and prevent its formation for days. The molecules include new antimicrobials that can replace thousands of toxic biocides used in consumer and industrial products and can be developed into new drug candidates to kill the biofilm-forming bacteria and fungi -- including the antimicrobial-resistant (AMR) Superbugs for which there is no cure. Today, Aequor has over 70 chemicals that are divided into categories: (1) Novel natural chemicals. Lonza validated that the primary natural chemical removed biofilm in minutes and stated: "Nothing else known can do this at non-toxic doses." (2) Specialty chemicals. 25 of these structural analogs are already approved under the U.S. Environmental Protection Agency (EPA)'s Toxic Substances Control Act, certified as "green" and available for immediate sale. These have been validated for the following agro-industrial verticals: (a) Surface cleaners: The U.S. Department of Agriculture validated that low concentrations of Aequor's formulations provide deep cleaning of inert, nano and organic surfaces and materials; (b) Water treatments: NASA validated that one dose of Aequor's treatment in the International Space Station's water reuse/recycling system lasted 15 months without replenishment. DOE validated that our treatments lower energy consumption by over 10% in buildings and industrial processes. Future validations include pilot projects with the EPA to test efficacy in hospital plumbing systems. (c) Algae cultivation and yeast fermentation: The U.S. Department of Energy (DOE) validated that Aequor's treatment boosted biomass of renewable feedstocks by 40% in half the time -- increasing the profitability of biofuels and biobased co-products. DOE also validated increased yields and crop protection of algae under cultivation in open ponds. A private oil and gas company validated decontamination of oilfield water. (3) New structural analogs. These kill Gram-negative and Gram-positive bacteria and fungi alone, in combinations with each other, and in combination with low doses of existing, ineffective antibiotics (including Penicillin), "potentiating" them to kill AMR pathogens at doses too low to trigger resistance. Both the U.S. National Institutes for Health (NIH) and Department of Defense (DOD) has executed contracts with Aequor to provide the pre-clinical trials needed for these new drug candidates to enter the regulatory approval pipelines. Aequor seeks partners/licensees to commercialize its specialty chemicals and support to evaluate the optimal methods to scale-up of several new structural analogs via activity-guided fractionation and/or biosynthesis in order to initiate the NIH and DOD pre-clinical trials.

Keywords: biofilm, potentiation, prevention, removal

Procedia PDF Downloads 99

Authors: Aminu Mohammed, Shahidul Islam

Abstract:

Aframomum melegueta K.Schum commonly known as Grains of Paradise has been a popularly used spice in most of the African food preparation. Available data have shown that ethyl acetate fraction from crude ethanolic extract exhibited α-amylase and α-glucosidase inhibitory actions, improved pancreatic β-cell damage and ameliorated insulin resistance in diabetic rats. Additionally, 6-gingerol, 6-shogaol, 6-paradol and oleanolic acid are shown to be the compounds responsible for the antidiabetic action of A. melegueta. However, detail antioxidant potential of this spice in a diabetic animal model has not yet been reported. Thus, the present study investigates the effect of oral consumption of A. melegueta fruit on the in vivo antioxidant status of type 2 diabetes (T2D) model of rats. T2D was induced in rats by feeding a 10% fructose solution ad libitum for two weeks followed by a single intraperitoneal injection of streptozotocin (40 mg/kg body weight (bw)). The animals were orally administered with 150 (DAML) or 300 mg/kg bw (DAMH) of the fraction once daily for four weeks. Data were analyzed by using a statistical software package (SPSS for Windows, version 22, IBM Corporation, NY, USA) using Tukey’s-HSD multiple range post-hoc test. Values were considered significantly different at p < 0.05. According to the data, after four weeks of intervention, diabetic untreated animals showed significantly (p < 0.05) elevation of blood glucose levels. The levels of thiobarbituric acid reactive substances (TBARS) were observed to increase with concomitant reduction of reduced glutathione (GSH) levels in the serum and organs (liver, kidney, heart and pancreas) of diabetic untreated animals. The activities of endogenous antioxidant enzymes (superoxide dismutase, catalase, glutathione peroxidase, and reductase) were greatly reduced in the serum and organs of diabetic untreated animals compared to the normal animals. These alterations were reverted to near-normal after the treatment of A. melegueta fruit in the treated groups (DAML & DAMH) within the study period, especially at the dose of 300 mg/kg bw. This potent antioxidant action may partly be attributed to the presence of the 6-Gingerol, 6-shogaol and 6-paradol are known to possess antioxidant action. The results of our study showed that A. melegueta intake improved the antioxidant status of T2D rats and therefore could be used to ameliorate the diabetes-induced oxidative damage.

Keywords: Aframomum melegueta, antioxidant, ethyl acetate extract, type 2 diabetes

Procedia PDF Downloads 300

Authors: Mehdi Tajdari, Farzad Mokhtarnejad, Fatemeh Moradi, Mehdi Najafizadeh

Abstract:

Nowadays, energy absorbing devices have been widely used in all vehicles and moving parts such as railway couches, aircraft, ships and lifts. The aim is to protect these structures from serious damages while subjected to impact loads, or to minimize human injuries while collision is occurred in transportation systems. These energy-absorbing devices can dissipate kinetic energy in a wide variety of ways like friction, facture, plastic bending, crushing, cyclic plastic deformation and metal cutting. On the other hand, various structures may be used as collapsible energy absorbers. Metallic cylindrical tubes have attracted much more attention due to their high stiffness and strength combined with the low weight and ease of manufacturing process. As a matter of fact, favorable crash worthiness characteristics for energy dissipation purposes can be achieved from axial collapse of tubes while they crush progressively in symmetric modes. However, experimental and theoretical results have shown that depending on various parameters such as tube geometry, material properties of tube, boundary and loading conditions, circular tubes buckle in different modes of deformation, namely, diamond and Euler collapsing modes. It is shown that when the tube length is greater than the critical length, the tube deforms in overall Euler buckling mode, which is an inefficient mode of energy absorption and needs to be avoided in crash worthiness applications. This study develops a new method with the aim of improving energy absorption characteristics of long steel circular tubes. Inserting a helical spring into the tubes is proved experimentally to be an efficient solution. In fact when a long tube is subjected to axial compression load, the spring prevents of undesirable Euler or diamond collapsing modes. This is because the spring reinforces the internal wall of tubes and it causes symmetric deformation in tubes. In this research three specimens were prepared and three tests were performed. The dimensions of tubes were selected so that in axial compression load buckling is occurred. In the second and third tests a spring was inserted into tubes and they were subjected to axial compression load in quasi-static and impact loading, respectively. The results showed that in the second and third tests buckling were not happened and the tubes deformed in symmetric modes which are desirable in energy absorption.

Keywords: energy absorption, circular tubes, collapsing deformation, crashworthiness

Procedia PDF Downloads 340

Authors: Martina Marinelli, Samanta Vellante, Francesco Pilotti, Daniele Di Valerio, Gaetanino Paolone

Abstract:

Any development in web marketing technology requires changes in information engineering to identify instruments and techniques suitable for the production of software applications for informative marketing. Moreover, for large web solutions, designing an interface that enables human interactions is a complex process that must bridge between informative marketing requirements and the developed solution. A user-friendly interface in web marketing applications is crucial for a successful business. The paper introduces mkInfo - a software platform that implements informative marketing. Informative marketing is a new interpretation of marketing which places the information at the center of every marketing action. The creative team includes software engineering researchers who have recently authored an article on automatic code generation. The authors have created the mkInfo software platform to generate informative marketing web applications. For each web application, it is possible to automatically implement an opt in page, a landing page, a sales page, and a thank you page: one only needs to insert the content. mkInfo implements an autoresponder to send mail according to a predetermined schedule. The mkInfo platform also includes e-commerce for a product or service. The stakeholder can access any opt-in page and get basic information about a product or service. If he wants to know more, he will need to provide an e-mail address to access a landing page that will generate an e-mail sequence. It will provide him with complete information about the product or the service. From this point on, the stakeholder becomes a user and is now able to purchase the product or related services through the mkInfo platform. This paper suggests a possible definition for Informative Marketing, illustrates its basic principles, and finally details the mkInfo platform that implements it. This paper also offers some Informative Marketing models, which are implemented in the mkInfo platform. Informative marketing can be applied to products or services. It is necessary to realize a web application for each product or service. The mkInfo platform enables the product or the service producer to send information concerning a specific product or service to all stakeholders. In conclusion, the technical contributions of this paper are: a different interpretation of marketing based on information; a modular architecture for web applications, particularly for one with standard features such as information storage, exchange, and delivery; multiple models to implement informative marketing; a software platform enabling the implementation of such models in a web application. Future research aims to enable stakeholders to provide information about a product or a service so that the information gathered about a product or a service includes both the producer’s and the stakeholders' point of view. The purpose is to create an all-inclusive management system of the knowledge regarding a specific product or service: a system that includes everything about the product or service and is able to address even unexpected questions.

Keywords: informative marketing, opt in page, software platform, web application

Procedia PDF Downloads 127

Authors: Anisah Ari

Abstract:

Effects of organized crime permeate all facets of life, including public health, socio-economic endeavors, and human security. If any element of this is affected, it impacts large-scale national and global interest. Seeking to address terrorist networks through technical thinking is like trying to kill a weed by just cutting off its branches. It will re-develop and expand in proportions beyond one’s imagination, even in horrific ways that threaten human security. The continent of Africa has been bedeviled by this menace, with little or no solution to the problem. Nigeria is dealing with a protracted insurgency that is perpetrated by a sect against any form of westernization. Reimagining approaches to dealing with pressing issues like terrorism may require engaging the right set of people in the conversation for any sustainable change. These are people who have lived through the daily effects of the violence that ensues from the activities of terrorist activities. Effective leadership is required for an inclusive process, where spaces are created for diverse voices to be heard, and multiple perspectives are listened to, and not just heard, that supports a determination of the realistic outcome. Addressing insurgency in Nigeria has experienced a lot of disinformation and uncertainty. This may be in part due to poor leadership or an iteration of technical solutions to adaptive challenge peacemaking efforts in Nigeria has focused on behaviors, attitudes and practices that contribute to violence. However, it is important to consider the underlying issues that build-up, ignite and fan the flames of violence—looking at conflict as a complex system, issues like climate change, low employment rates, corruption and the impunity of discrimination due to ethnicity and religion. This article will be looking at an option of the more relational way of addressing insurgency through adaptive approaches that embody engagement and solutions with the people rather than for the people. The construction of a local turn in peacebuilding is informed by the need to create a locally driven and sustained peace process that embodies the culture and practices of the people in enacting an everyday peace beyond just a perennial and universalist outlook. A critical analysis that explores the socially identified individuals and situations will be made, considering the more adaptive approach to a complex existential challenge rather than a universalist frame. Case Study and Ethnographic research approach to understand what other scholars have documented on the matter and also a first-hand understanding of the experiences and viewpoints of the participants.

Keywords: terrorism, adaptive, peace, culture

Procedia PDF Downloads 103

Authors: Bollu Mounica

Abstract:

Background: Nowadays drug related problems were seen very commonly within the health care practice. These could result in the medication errors, adverse events, drug interactions and harm to patients. Pharmacist has an identified role in minimizing and preventing such type of problems. Objectives: To detect the incidence of drug related problems for the hospitalized patient, and to analyze the clinical pharmacist interventions performed during the review of prescription orders of the general medicine, psychiatry, surgery, pediatrics, gynaecology units of a large tertiary care teaching hospital. Methods: It was a retrospective, observational and interventional study. The analysis took place daily with the following parameters: dose, rate of administration, presentation and/or dosage form, presence of inappropriate/unnecessary drugs, necessity of additional medication, more proper alternative therapies, presence of relevant drug interactions, inconsistencies in prescription orders, physical-chemical incompatibilities/solution stability. From this evaluation, the drug therapy problems were classified, as well as the resulting clinical interventions. For a period starting November 2012 until December 2014, the inpatient medication charts and orders were identified and rectified by ward and practicing clinical pharmacists within the inpatient pharmacy services in a tertiary care teaching hospital on routine daily activities. Data was collected and evaluated. The causes of this problem were identified. Results: A total of 360 patients were followed. Male (71.66%) predominance was noted over females (28.33%). Drug related problems were more commonly seen in patients aged in between 31-60. Most of the DRP observed in the study resulted from the dispensing errors (26.11%), improper drug selection (17.22%), followed by untreated indications (14.4%) Majority of the clinical pharmacist recommendations were on need for proper dispensing (26.11%), and drug change (18.05%). Minor significance of DRPs were noted high (41.11 %), whereas (35.27 %) were moderate and (23.61 %) were major. The acceptance rate of intervening clinical pharmacist recommendation and change in drug therapy was found to be high (86.66%). Conclusion: Our study showed that the prescriptions reviewed had some drug therapy problem and the pharmacist interventions have promoted positive changes needed in the prescriptions. In this context, routine participation of clinical pharmacists in clinical medical rounds facilitates the identification of DRPs and may prevent their occurrence.

Keywords: drug related problems, clinical pharmacist, drug prescriptions, drug related problems, intervention

Procedia PDF Downloads 304

Authors: Luis Guilherme Resende Santos, Ido Nevat, Leslie Norford

Abstract:

The Urban Heat Island (UHI) is characterized by increased air temperatures in urban areas compared to undeveloped rural surrounding environments. With urbanization and densification, the intensity of UHI increases, bringing negative impacts on livability, health and economy. In order to reduce those effects, it is required to take into consideration design factors when planning future developments. Given design constraints such as population size and availability of area for development, non-trivial decisions regarding the buildings’ dimensions and their spatial distribution are required. We develop a framework for optimization of urban design in order to jointly minimize UHI intensity and buildings’ energy consumption. First, the design constraints are defined according to spatial and population limits in order to establish realistic boundaries that would be applicable in real life decisions. Second, the tools Urban Weather Generator (UWG) and EnergyPlus are used to generate outputs of UHI intensity and total buildings’ energy consumption, respectively. Those outputs are changed based on a set of variable inputs related to urban morphology aspects, such as building height, urban canyon width and population density. Lastly, an optimization problem is cast where the utility function quantifies the performance of each design candidate (e.g. minimizing a linear combination of UHI and energy consumption), and a set of constraints to be met is set. Solving this optimization problem is difficult, since there is no simple analytic form which represents the UWG and EnergyPlus models. We therefore cannot use any direct optimization techniques, but instead, develop an indirect “black box” optimization algorithm. To this end we develop a solution that is based on stochastic optimization method, known as the Cross Entropy method (CEM). The CEM translates the deterministic optimization problem into an associated stochastic optimization problem which is simple to solve analytically. We illustrate our model on a typical residential area in Singapore. Due to fast growth in population and built area and land availability generated by land reclamation, urban planning decisions are of the most importance for the country. Furthermore, the hot and humid climate in the country raises the concern for the impact of UHI. The problem presented is highly relevant to early urban design stages and the objective of such framework is to guide decision makers and assist them to include and evaluate urban microclimate and energy aspects in the process of urban planning.

Keywords: building energy consumption, stochastic optimization, urban design, urban heat island, urban weather generator

Procedia PDF Downloads 131

Authors: Mandeep Kaur, K. C. Sharma, P. L. Sharma, R. S. Chandel

Abstract:

Cauliflower is an important vegetable crop grown throughout the world and is attacked by a large number of insect pests at various stages of the crop growth. Amongst them, the cabbage aphid, Brevicoryne brassicae (Linnaeus) (Hemiptera: Aphididae) is an important insect pest. Continued feeding by both nymphs and adults of this aphid causes yellowing, wilting and stunting of plants. Amongst various management practices, the use of resistant cultivars is important and can be an effective method of reducing the population of this aphid. So it is imperative to know the complete record on various biological parameters and life table on specific cultivars. The biology and life fertility of the cabbage aphid were studied on five cauliflower cultivars viz. Megha, Shweta, K-1, PSB-1 and PSBK-25 under controlled temperature conditions of 20 ± 2°C, 70 ± 5% relative humidity and 16:8 h (Light: Dark) photoperiods. For studying biology; apterous viviparous adults were picked up from the laboratory culture of all five cauliflower cultivars after rearing them at least for two generations and placed individually on the desired plants of cauliflower cultivars grown in pots with ten replicates of each. Daily record on the duration of nymphal period, adult longevity, mortality in each stage and the total number of progeny produced per female was made. This biological data were further used to construct life fertility table on each cultivar. Statistical analysis showed that there was a significant difference ( P  < 0.05) between the different growth stages and the mean number of laid nymphs. The maximum and minimum growth periods were observed on Shweta and Megha (at par with K-1) cultivars, respectively. The maximum number of nymphs were laid on Shweta cultivar (26.40 nymphs per female) and minimum on Megha (at par with K-1) cultivar (15.20 nymphs per female). The true intrinsic rate of increase (rm) was found to be maximum on Shweta (0.233 nymphs/female/day) followed by PSB K-25 (0.207 nymphs/female/day), PSB-1 (0.203 nymphs/female/day), Megha (0.166 nymphs/female/day) and K-1 (0.153 nymphs/female/day). The finite rate of natural increase (λ) was also found to be in the order: K-1 < Megha < PSB-1 < PSBK-25 < Shweta whereas the doubling time (DT) was in the order of K-1 >Megha> PSB-1 >PSBk-25> Shweta. The aphids reared on the K-1 cultivar had the lowest values of rm & λ and the highest value of DT whereas on Shweta cultivar the values of rm & λ were the highest and the lowest value of DT. So on the basis of these studies, K-1 cultivar was found to be the least suitable and the Shweta cultivar was the most suitable for the cabbage aphid population growth. Although the cauliflower cultivars used in different parts of the world may be different yet the results of the present studies indicated that the application of cultivars affecting multiplication rate and reproductive parameters could be a good solution for the management of the cabbage aphid.

Keywords: biology, cauliflower, cultivars, fertility

Procedia PDF Downloads 184

Authors: L. Mercier, D. Beladjine, K. Beddiar

Abstract:

The digital transition of building in France brings many changes which some have been able to face very quickly, while others are struggling to find their place and the interest that BIM can bring in their profession. BIM today is already adopted or initiated by construction professionals. However, this change, which can be drastic for some, prevents them from integrating it definitively. This is the case with architects. The profession is shared on the practice of BIM in its exercise. The risk of not adopting this new working method now and of not wanting to switch to its new digital tools leads us to question the future of the profession in view of the gap that is likely to be created within project management. In order to deal with the subject efficiently, our work was based on a documentary watch on BIM and then on the profession of architect, which allowed us to establish links on these two subjects. The observation of the economic model towards which the agencies tend and the trend of the sought after profiles made it possible to develop the opportunities and the brakes likely to impact the future of the profession of architect. The centralization of research directs work towards the conclusion that the model implemented by companies does not allow to integrate BIM within their structure. A solution hypothesis was then issued, focusing on the development of agencies through the diversity of profiles, skills to be integrated internally with the aim of diversifying their skills, and their business practices. In order to address this hypothesis of a multidisciplinary agency model, we conducted a survey of architectural firms. It is built on the model of Anglo-Saxon countries, which do not have the same functioning in comparison to the French model. The results obtained showed a risk of gradual disappearance on the market from small agencies in favor of those who will have and could take this BIM working method. This is why the architectural profession must, first of all, look at what is happening within its training before absolutely wanting to diversify the profiles to integrate into its structure. This directs the study on the training of architects. The schools of French architects are generally behind schedule if we allow the comparison to the schools of engineers. The latter is currently experiencing a slight improvement with the emergence of masters and BIM options during the university course. If the training of architects develops towards learning BIM and the agencies have the desire to integrate different but complementary profiles, then they will develop their skills internally and therefore open their profession to new functions. The place of BIM Management on projects will allow the architect to remain in control of the project because of their overall vision of the project. In addition, the integration of BIM and more generally of the life cycle analysis of the structure will make it possible to guarantee eco-design or eco-construction by approaching the constraints of sustainable development omnipresent on the planet.

Keywords: building information modelling, BIM, BIM management, BIM manager, BIM architect

Procedia PDF Downloads 113

Authors: Smriti Rastogi, Narsingh Verma

Abstract:

Background: A vast body of research exists on the use of oral hypoglycaemic drugs, insulin injections and the like in managing diabetes but no such research exists that has taken into consideration the parameter of time restricted meal intake and its positive effects in managing diabetes. The utility of this project is immense as it offers a solution to the woes of diabetics based on circadian rhythm and normal physiology of the human body. Method: 80 Diabetics, enrolled from the Out Patient Department of Endocrinology, KGMU (King George's Medical University) were randomly divided based on consent to early dinner TRM(time restricted meal) group or not (control group). Follow up was done at six months and 12 months for anthropometric measurement, height, weight, waist-hip ratio, neck size, fasting, postprandial blood sugar, HbA1c, serum urea, serum creatinine, and lipid profile. The patient was given a clear understanding of chronomedicine and how it affects their health. A single intervention was done - the timing of dinner was at or around 7 pm for TRM group. Result: 65% of TRM group and 40 %(non- TRM) had normal HbA1c after 12 months. HbA1c in TRM Group (first visit to second follow up) had a significant p value=0.017. A p value of <0.0001 was observed on comparing the values of blood sugar (fasting) in TRM Group from the first visit and second follow up. The values of blood sugar (postprandial) in TRM Group (first visit and second follow up) showed a p-value <0.0001 (highly significant). Values of the three parameters were non- significant in the control group. Hip size(First Visit to Second Follow Up) TRM Group showed a p-value = 0.0344 (Significant) (Difference between means=2.762 ± 1.261)Detailed results of the above parameters and a few newer ones will be presented at the conference. Conclusion: Time restricted meal intake in diabetics shows promise and is worth exploring further. Time Restricted Meal intake in Type 2 diabetics has a significant effect in controlling and maintaining HbA1c as the reduction in HbA1c value was very significant in the TRM group vs. the control group. Similar highly significant results were obtained in the case of fasting and postprandial values of blood sugar in the TRM group when compared to the control group. The effects of time restricted meal intake in diabetics show promise and are worth exploring further. It is one of the first studies which have been undertaken in Indian diabetics, although the initial data obtained is encouraging yet further research and study are required to corroborate results.

Keywords: chronomedicine, diabetes, endocrinology, time restricted meal intake

Procedia PDF Downloads 126

Authors: J. Hakula

Abstract:

Discussion on euthanasia is a continuous process. Euthanasia is defined as 'deliberately ending a patient's life by administering life-ending drugs at the patient's explicit request'. With few exceptions, worldwide in most countries human societies have not been able to agree on some fundamental issues concerning ultimate decisions of life and death. Outranking methods in voting oriented social choice theory and multicriteria decision-making (MCDM) can be applied to issues in medical ethics. There is a wide range of voting methods, and using different methods the same group of voters can end up with different outcomes. In the MCDM context, decision alternatives can be substituted for candidates, and criteria for voters. The view chosen here is that of a single decision-maker. Initially, three alternatives and three criteria are chosen. Pairwise and basic positional voting rules - plurality, anti-plurality and the Borda count - are applied. In the MCDM solution, criteria are put weights by giving them the more 'votes'; the more important the decision-maker ranks them. A hypothetical example on evaluating properties of euthanasia consists of three alternatives A, B, and C, which are ranked according to three criteria - the patient’s willingness to cooperate, general action orientation (active/passive), and cost-effectiveness - the criteria having weights 7, 5, and 4, respectively. Using the plurality rule and the weights given to criteria, A is the best alternative, B and C thereafter. In pairwise comparisons, both B and C defeat A with weight scores 7 to 9. On the other hand, B is defeated by C with weights 11 to 5. Thus, C (i.e. the so-called Condorcet winner) defeats both A and B. The best alternative using the plurality principle is not necessarily the best in the pairwise sense, the conflict remaining unsolved with or without additional weights. Positional rules are sensitive to variations in alternative sets. In the example above, the plurality rule gives the rank ABC. If we leave out C, the plurality ranking between A and B results in BA. Withdrawing B or A the ranking is CA and CB, respectively. In pairwise comparisons an analogous problem emerges when the number of criteria is varied. Cyclic preferences may lead to a total tie, and no (rational) choice between the alternatives can be made. In conclusion, the choice of the best commitment to re-evaluate euthanasia, with criteria left unchanged, depends entirely on the evaluation method used. The right strategies matter, too. Future studies might concern the problem of an abstention - a situation where voters do not vote - and still their best candidate may win. Or vice versa, actively giving the ballot to their first rank choice might lead to a total loss. In MCDM terms, a decision might occur where some central criteria are not actively involved in the best choice made.

Keywords: medical ethics, euthanasia, voting methods, multicriteria decision-making

Procedia PDF Downloads 157

Authors: İrem Yetkin, Feray Maden, Seda Tosun, Yenal Akgün, Özgür Kilit, Koray Korkmaz, Gökhan Kiper, Mustafa Gündüzalp

Abstract:

Forced migration, whether caused by conflicts or other factors, frequently places individuals in vulnerable situations, necessitating immediate access to shelter. To promptly address the immediate needs of affected individuals, temporary shelters are often established. These shelters are characterized by their adaptable and functional nature, encompassing lightweight and sustainable structural systems, rapid assembly capabilities, modularity, and transportability. The shelter design is contingent upon demand, resulting in distinct phases for different structural forms. A multi-phased shelter approach covers emergency response, temporary shelter, and permanent reconstruction. Emergency shelters play a critical role in providing immediate life-saving aid, while temporary and transitional shelters, which are also called “t-shelters,” offer longer-term living environments during the recovery and rebuilding phases. Among these, temporary shelters are more extensively covered in the literature due to their diverse inhabiting functions. The roles of emergency shelters and temporary shelters are inherently separate, addressing distinct aspects of sheltering processes. Given their prolonged usage, temporary shelters are built for greater durability compared to emergency shelters. Nonetheless, inadequacies in temporary shelters can lead to challenges in ensuring habitability. Issues like non-expandable structures unsuitable for accommodating large families, the use of short-term shelters that worsen conditions, non-waterproof materials providing insufficient protection against bad weather conditions, and complex installation systems contribute to these problems. Given the aforementioned problems, there arises a need to develop adaptive shelters featuring lightweight components for ease of transport, possess the ability for rapid assembly, and utilize durable materials to withstand adverse weather conditions. In this study, first, the state-of-the-art on temporary shelters is presented. Then, an adaptive temporary shelter composed of foldable plates is proposed, which can easily be assembled and transportable. The proposed shelter is deliberated upon its movement capacity, transportability, and flexibility. This study makes a valuable contribution to the literature since it not only offers a systematic analysis of temporary shelters utilizing kinetic systems but also presents a practical solution that meets the necessary design requirements.

Keywords: deployable structures, foldable plates, forced migration, temporary shelters

Procedia PDF Downloads 72

Authors: Márcia Afonso, Marisa Dinis-Almeida, Cristina Fael

Abstract:

Climate change, namely precipitation patterns alteration, has led to extreme conditions such as floods and droughts. In turn, excessive construction has led to the waterproofing of the soil, increasing the surface runoff and decreasing the groundwater recharge capacity. The permeable pavements used in areas with low traffic lead to a decrease in the probability of floods peaks occurrence and the sediments reduction and pollutants transport, ensuring rainwater quality improvement. This study aims to evaluate the porous asphalt performance, developed in the laboratory, with addition of cellulosic fibres. One of the main objectives of cellulosic fibres use is to stop binder drainage, preventing its loss during storage and transport. Comparing to the conventional porous asphalt the cellulosic fibres addition improved the porous asphalt performance. The cellulosic fibres allowed the bitumen content increase, enabling retention and better aggregates coating and, consequently, a greater mixture durability. With this solution, it is intended to develop better practices of resilience and adaptation to the extreme climate changes and respond to the sustainability current demands, through the eco-friendly materials use. The mix design was performed for different size aggregates (with fine aggregates – PA1 and with coarse aggregates – PA2). The percentage influence of the fibres to be used was studied. It was observed that overall, the binder drainage decreases as the cellulose fibres percentage increases. It was found that the PA2 mixture obtained most binder drainage relative to PA1 mixture, irrespective of the fibres percentage used. Subsequently, the performance was evaluated through laboratory tests of indirect tensile stiffness modulus, water sensitivity, permeability and permanent deformation. The stiffness modulus for the two mixtures groups (with and without cellulosic fibres) presented very similar values between them. For the water sensitivity test it was observed that porous asphalt containing more fine aggregates are more susceptible to the water presence than mixtures with coarse aggregates. The porous asphalt with coarse aggregates have more air voids which allow water to pass easily leading to ITSR higher values. In the permeability test was observed that asphalt porous without cellulosic fibres presented had lower permeability than asphalt porous with cellulosic fibres. The resistance to permanent deformation results indicates better behaviour of porous asphalt with cellulosic fibres, verifying a bigger rut depth in porous asphalt without cellulosic fibres. In this study, it was observed that porous asphalt with bitumen higher percentages improve the performance to permanent deformation. This fact was only possible due to the bitumen retention by the cellulosic fibres.

Keywords: binder drainage, cellulosic fibres, permanent deformation, porous asphalt

Procedia PDF Downloads 226

Authors: Zhijie Li, Wenhui Peng, Zelong Yuan, Jianchun Wang

Abstract:

Turbulence is a complex phenomenon that plays a crucial role in various fields, such as engineering, atmospheric science, and fluid dynamics. Predicting and understanding its behavior over long time scales have been challenging tasks. Traditional methods, such as large-eddy simulation (LES), have provided valuable insights but are computationally expensive. In the past few years, machine learning methods have experienced rapid development, leading to significant improvements in computational speed. However, ensuring stable and accurate long-term predictions remains a challenging task for these methods. In this study, we introduce the implicit U-net enhanced Fourier neural operator (IU-FNO) as a solution for stable and efficient long-term predictions of the nonlinear dynamics in three-dimensional (3D) turbulence. The IU-FNO model combines implicit re-current Fourier layers to deepen the network and incorporates the U-Net architecture to accurately capture small-scale flow structures. We evaluate the performance of the IU-FNO model through extensive large-eddy simulations of three types of 3D turbulence: forced homogeneous isotropic turbulence (HIT), temporally evolving turbulent mixing layer, and decaying homogeneous isotropic turbulence. The results demonstrate that the IU-FNO model outperforms other FNO-based models, including vanilla FNO, implicit FNO (IFNO), and U-net enhanced FNO (U-FNO), as well as the dynamic Smagorinsky model (DSM), in predicting various turbulence statistics. Specifically, the IU-FNO model exhibits improved accuracy in predicting the velocity spectrum, probability density functions (PDFs) of vorticity and velocity increments, and instantaneous spatial structures of the flow field. Furthermore, the IU-FNO model addresses the stability issues encountered in long-term predictions, which were limitations of previous FNO models. In addition to its superior performance, the IU-FNO model offers faster computational speed compared to traditional large-eddy simulations using the DSM model. It also demonstrates generalization capabilities to higher Taylor-Reynolds numbers and unseen flow regimes, such as decaying turbulence. Overall, the IU-FNO model presents a promising approach for long-term dynamics prediction in 3D turbulence, providing improved accuracy, stability, and computational efficiency compared to existing methods.

Keywords: data-driven, Fourier neural operator, large eddy simulation, fluid dynamics

Procedia PDF Downloads 74

Authors: Ruwandika Perera

Abstract:

Even though the Sri Lankan government provides a reasonable level of support for students at all levels of the school system, for example, free education, textbooks, school uniforms, subsidized public transportation, and school meals, low participation in learning among secondary students is an issue warranting investigation, particularly in low socio-economic districts. This study attempted to determine the levels of motivation and engagement amongst students in a number of schools in two low socio-economic districts of Sri Lanka. This study employed quantitative research design in an attempt to determine levels of motivation and engagement amongst Sri Lankan secondary school students. Motivation and Engagement Scale-Junior School (MES-JS) was administered among 100 Sinhala-medium and 100 Tamil-medium eighth-grade students (50 students from each gender). The mean age of the students was 12.8 years. Schools were represented by type 2 government schools located in Monaragala and Nuwara Eliya districts in Sri Lanka. Confirmatory factor analysis (CFA) was conducted to measure the construct validity of the scale. Since this did not provide a robust solution, exploratory factor analysis (EFA) was conducted. Four factors were identified; Failure Avoidance and Anxiety (FAA), Positive Motivation (PM), Uncertain Control (UC), and Positive Engagement (PE). An independent-samples t-test was conducted to compare PM, PE, FAA, and UC in gender and ethnic groups. There was no significant difference identified for PE, FAA, and UC scales based upon gender. These results indicate that for the participants in this study, there were no significant differences based on gender in the levels of failure avoidance and anxiety, uncertain control, and positive engagement in the school experience. But, the result for the PM scale was close to significant, indicating there may be differences based on gender for positive motivation. A significant difference exists for all scales based on ethnicity, with the mean result for the Tamil students being significantly higher than that for the Sinhala students. These results indicate those Sinhala-medium students’ levels of positive motivation and positive engagement in learning was lower than Tamil-medium students. Also, these results indicate those Tamil-medium students’ levels of failure avoidance, anxiety, and uncertain control was higher than Sinhala-medium students. It could be concluded that male students levels of PM were significantly lower than female students. Also, Sinhala-medium students’ levels of PM and PE was lower than Tamil-medium students, and Tamil-medium students levels of FAA and UC was significantly higher than Sinhala-medium students. Thus, there might be particular school-related conditions affecting this situation, which are related to early adolescents’ motivation and engagement in learning.

Keywords: early adolescents, engagement, low socio-economic districts, motivation

Procedia PDF Downloads 163

Authors: Saeed Bagherifam, Trevor Brown, Chris Fellows, Ravi Naidu

Abstract:

Over the last century, rapid urbanization, industrial emissions, and mining activities have resulted in widespread contamination of the environment by heavy metal(loid)s. Arsenic (As) is a toxic metalloid belonging to group 15 of the periodic table, which occurs naturally at low concentrations in soils and the earth’s crust, although concentrations can be significantly elevated in natural systems as a result of dispersion from anthropogenic sources, e.g., mining activities. Bioavailability is the fraction of a contaminant in soils that is available for uptake by plants, food chains, and humans and therefore presents the greatest risk to terrestrial ecosystems. Numerous attempts have been made to establish in situ and ex-situ technologies of remedial action for remediation of arsenic-contaminated soils. In situ stabilization techniques are based on deactivation or chemical immobilization of metalloid(s) in soil by means of soil amendments, which consequently reduce the bioavailability (for biota) and bioaccessibility (for humans) of metalloids due to the formation of low-solubility products or precipitates. This study investigated the effectiveness of two different types of synthetic manganese and iron oxides (birnessite and goethite) for stabilization of As in a soil spiked with 1000 mg kg⁻¹ of As and treated with 10% dosages of soil amendments. Birnessite was made using HCl and KMnO₄, and goethite was synthesized by the dropwise addition of KOH into Fe(NO₃) solution. The resulting contaminated soils were subjected to a series of chemical extraction studies including sequential extraction (BCR method), single-step extraction with distilled (DI) water, 2M HNO₃ and simplified bioaccessibility extraction tests (SBET) for estimation of bioaccessible fractions of As in two different soil fractions ( < 250 µm and < 2 mm). Concentrations of As in samples were measured using inductively coupled plasma mass spectrometry (ICP-MS). The results showed that soil with birnessite reduced bioaccessibility of As by up to 92% in both soil fractions. Furthermore, the results of single-step extractions revealed that the application of both birnessite and Goethite reduced DI water and HNO₃ extractable amounts of arsenic by 75, 75, 91, and 57%, respectively. Moreover, the results of the sequential extraction studies showed that both birnessite and goethite dramatically reduced the exchangeable fraction of As in soils. However, the amounts of recalcitrant fractions were higher in birnessite, and Goethite amended soils. The results revealed that the application of both birnessite and goethite significantly reduced bioavailability and the exchangeable fraction of As in contaminated soils, and therefore birnessite and Goethite amendments might be considered as promising adsorbents for stabilization and remediation of As contaminated soils.

Keywords: arsenic, bioavailability, in situ stabilisation, metalloid(s) contaminated soils

Procedia PDF Downloads 135

Authors: Priyal Sepaha

Abstract:

A refugee crisis is manifested by challenges, both for the refugees and the asylum giving state. The situation turns into a mega-crisis when the situation is prejudicially handled by the home state, inappropriate refugee laws, exploding refugee population, and above all, no hope of any foreseeable solution or remedy. This paper studies the impact on the capability of stateless Rohingyas to migrate and seek refuge due to the enforcement of rigid criteria of movement imposed both by Myanmar as well as the adjoining countries in the name of national security. This theoretical study identifies the issues and the key factors and players which have precipitated the crisis. It further discusses the possible ramifications in the home, asylum giving, and the adjoining countries for not discharging their roles aptly. Additionally, an attempt has been made to understand the scarce response given to the impending crisis by the regional organizations like SAARC, ASEAN and CHOGAM as well as international organizations like United Nations Human Rights Council, Security Council, Office of High Commissioner for Refugees and so on, in the name of inadequacy of monetary funds and physical resources. Based on the refugee laws and practices pertaining to the case of Rohingyas, this paper analyses that the Rohingya Crisis is in dire need of an effective action plan to curb and resolve the biggest humanitarian crisis situation of the century. This mounting human tragedy can be mitigated permanently, by strengthening existing and creating new interdependencies among all stakeholders, as further ignorance can drive the countries of the Indian Sub-continent, in particular, and South East Asia, by and large into a violent civil war for seizing long-awaited civil rights by the marginalized Rohingyas. To curb this mass crisis, it will require the application of coercive pressure and diplomatic pursuance on the home country to acknowledge the rights of its fleeing citizens. This further necessitates mustering adequate monetary funds and physical resources for the asylum providing state. Additional challenges such as devising mechanisms for the refugee’s safe return, comprehensive planning for their holistic economic development and rehabilitation plan are needed. These, however, can only come into effect with a conscious strive by the regional and international community to fulfil their assigned role.

Keywords: asylum, citizenship, crisis, humanitarian, human rights, refugee, rohingya

Procedia PDF Downloads 132