Search results for: cold start

Authors: Waled A. Dawoud, Abdelazim M. Negm, Nasser M. Saleh

Abstract:

Offshore piling generates underwater sound at level high enough to cause physical damage or hearing impairment to the marine mammals. Several methods can be used to mitigate the effect of underwater noise from offshore pile driving on marine mammals which can be divided into three main approaches. The first approach is to keep the mammal out of the high-risk area by using aversive sound waves produced by acoustic mitigation devices such as playing-back of mammal's natural predator vocalization, alarm or distress sounds, and anthropogenic sound. The second approach is to reduce the amount of underwater noise from pile driving using noise mitigation techniques such as bubble curtains, isolation casing, and hydro-sound dampers. The third approach is to eliminate the overlap of underwater waves by using prolonged construction process. To investigate the effectiveness of different noise mitigation methods; a pile driven with 235 kJ rated energy diesel hammer near Jeddah Coast, Kingdom of Saudi Arabia was used. Using empirical sound exposure model based on Red Sea characteristics and limits of National Oceanic and Atmospheric Administration; it was found that the aversive sound waves should extend to 1.8 km around the pile location. Bubble curtains can reduce the behavioral disturbance area up to 28%; temporary threshold shift up to 36%; permanent threshold shift up to 50%; and physical injury up to 70%. Isolation casing can reduce the behavioral disturbance range up to 12%; temporary threshold shift up to 21%; permanent threshold shift up to 29%; and physical injury up to 46%. Hydro-sound dampers efficiency depends mainly on the used technology and it can reduce the behavioral disturbance range from 10% to 33%; temporary threshold shift from 18% to 25%; permanent threshold shift from 32% to 50%; and physical injury from 46% to 60%. To prolong the construction process, it was found that the single pile construction, use of soft start, and keep time between two successive hammer strikes more than 3 seconds are the most effective techniques.

Keywords: offshore pile driving, sound propagation models, noise effects on marine mammals, Underwater noise mitigation

Procedia PDF Downloads 519

Authors: Aschalew C. Workneh, K. S. Hari Prasad, C. S. P. Ojha

Abstract:

The crop water stress index (CWSI) is a cost-effective, non-destructive, and simple technique for tracking the start of crop water stress. This study investigated the feasibility of CWSI derived from canopy temperature to detect the water status of wheat crops. Artificial intelligence (AI) techniques have become increasingly popular in recent years for determining CWSI. In this study, the performance of two AI techniques, adaptive neuro-fuzzy inference system (ANFIS) and self-organizing maps (SOM), are compared while determining the CWSI of paddy crops. Field experiments were conducted for varying irrigation water applications during two seasons in 2022 and 2023 at the irrigation field laboratory at the Civil Engineering Department, Indian Institute of Technology Roorkee, India. The ANFIS and SOM-simulated CWSI values were compared with the experimentally calculated CWSI (EP-CWSI). Multiple regression analysis was used to determine the upper and lower CWSI baselines. The upper CWSI baseline was found to be a function of crop height and wind speed, while the lower CWSI baseline was a function of crop height, air vapor pressure deficit, and wind speed. The performance of ANFIS and SOM were compared based on mean absolute error (MAE), mean bias error (MBE), root mean squared error (RMSE), index of agreement (d), Nash-Sutcliffe efficiency (NSE), and coefficient of correlation (R²). Both models successfully estimated the CWSI of the paddy crop with higher correlation coefficients and lower statistical errors. However, the ANFIS (R²=0.81, NSE=0.73, d=0.94, RMSE=0.04, MAE= 0.00-1.76 and MBE=-2.13-1.32) outperformed the SOM model (R²=0.77, NSE=0.68, d=0.90, RMSE=0.05, MAE= 0.00-2.13 and MBE=-2.29-1.45). Overall, the results suggest that ANFIS is a reliable tool for accurately determining CWSI in wheat crops compared to SOM.

Keywords: adaptive neuro-fuzzy inference system, canopy temperature, crop water stress index, self-organizing map, wheat

Procedia PDF Downloads 34

Authors: Inkeri Jaaskelainen

Abstract:

The purpose of this study is to shed light on what it is like to study in apprenticeship training using Finnish as a second language. This study examines the stories and experiences of apprenticeship students learning and studying Finnish as part of their vocational studies. Also, this pilot study examines the effects of learning to pronounce Finnish through body motions and gestures. Many foreign students choose apprenticeships and start vocational training too early, while their language skills in Finnish are still very weak. Both duties at work and school assignments require reasonably good general language skills (B1.1), and, especially at work, language skills are also a safety issue. At work, students should be able to simultaneously learn Finnish and do vocational studies in a noisy, demanding, and stressful environment. Learning and understanding new things is very challenging under these circumstances and sometimes students get exhausted and experience a lot of stress - which makes learning even more difficult. Students are different from each other and so are their ways to learn. Thereafter, one of the most important features of apprenticeship training and second language learning is a good understanding of adult learners and their needs. Kinaesthetic methods are an effective way to support adult students’ cognitive skills and make learning more relaxing and fun. Empirical findings show that language learning can indeed be supported in physical ways, by body motions and gestures. The method used here, named TFFL (Touch and Feel Foreign Languages), was designed to support adult language learning, to correct or prevent language fossilization, and to help the student to manage emotions. Finnish is considered as a difficult language to learn, mostly because it is so different from nearly all other languages. Many learners complain that they are lost or confused and there is a need to find a way to simultaneously learn the language and to handle negative emotion that comes from the Finnish language and the learning process itself. Due to the nature of the Finnish language, good pronunciation skills are needed just to understand the way the language work. Movements (body movements etc.) are a natural part of many cultures, but not Finnish. In Finland, students have traditionally been expected to stay still, and that is not a natural way for many foreign students. However, the kinaesthetic TFFL method proved out to be a useful way to help some L2 students to feel phonemes, rhythm, and intonation, to improve their Finnish, and, thereby, also to successfully complete their vocational studies.

Keywords: Finnish, fossilization, interference, kinaesthetic method

Procedia PDF Downloads 110

Authors: Prakash M.N, Mahesh G, Muhammed Rafi K.M, Shiju P. Nair

Abstract:

Introduction: In launch vehicle missions, Reaction Control thrusters are being used for the three-axis stabilization of the vehicle during the coasting phases. A pressure-fed propulsion system is used for the operation of these thrusters due to its less complexity. In liquid stages, these thrusters are designed to draw propellant from the same tank used for the main propulsion system. So in order to regulate the propellant flow rates of these thrusters, flow control orifices are used in feed lines. These orifices are calibrated separately as per the flow rate requirement of individual thrusters for the nominal operating conditions. In some missions, it was observed that the thrusters were operated at higher thrust than nominal. This point was addressed through a series of cold flow and hot tests carried out in-ground and this paper elaborates the details of the same. Discussion: In order to find out the exact reason for this phenomenon, two flight configuration thrusters were identified and hot tested in the ground with calibrated orifices and feed lines. During these tests, the chamber pressure, which is directly proportional to the thrust, is measured. In both cases, chamber pressures higher than the nominal by 0.32bar to 0.7bar were recorded. The increase in chamber pressure is due to an increase in the oxidizer flow rate of both the thrusters. Upon further investigation, it is observed that the calibration of the feed line is done with ambient pressure downstream. But in actual flight conditions, the orifices will be subjected to operate with 10 to 11bar pressure downstream. Due to this higher downstream pressure, the flow through the orifices increases and thereby, the thrusters operate with higher chamber pressure values. Conclusion: As part of further investigatory tests, two numbers of fresh thrusters were realized. Orifice tuning of these thrusters was carried out in three different ways. In the first trial, the orifice tuning was done by simulating 1bar pressure downstream. The second trial was done with the injector assembled downstream. In the third trial, the downstream pressure equal to the flight injection pressure was simulated downstream. Using these calibrated orifices, hot tests were carried out in simulated vacuum conditions. Chamber pressure and flow rate values were exactly matching with the prediction for the second and third trials. But for the first trial, the chamber pressure values obtained in the hot test were more than the prediction. This clearly shows that the flow is detached in the 1st trial and attached for the 2nd & 3rd trials. Hence, the error in tuning the flow control orifices is pinpointed as the reason for this higher chamber pressure observed in flight.

Keywords: reaction control thruster, propellent, orifice, chamber pressure

Procedia PDF Downloads 184

Authors: Virag Vass, Ilona Bereczki, Erzsebet Szabo, Nora Debreczeni, Aniko Borbas, Pal Herczegh, Arpad Tosaki

Abstract:

Hydrogen sulfide (H₂S) is a toxic gas, but it is produced by certain tissues in a small quantity. According to earlier studies, ibuprofen and H₂S has a protective effect against damaging heart tissue caused by ischemia-reperfusion. Recently, we have been investigating the effect of a new water-soluble H₂S releasing ibuprofen molecule administered after artificially generated ischemia-reperfusion on isolated rat hearts. The H₂S releasing property of the new ibuprofen derivative was investigated in vitro in medium derived from heart endothelial cell isolation at two concentrations. The ex vivo examinations were carried out on rat hearts. Rats were anesthetized with an intraperitoneal injection of ketamine, xylazine, and heparin. After thoracotomy, hearts were excised and placed into ice-cold perfusion buffer. Perfusion of hearts was conducted in Langendorff mode via the cannulated aorta. In our experiments, we studied the dose-effect of the H₂S releasing molecule in Langendorff-perfused hearts with the application of gradually increasing concentration of the compound (0- 20 µM). The H₂S releasing ibuprofen derivative was applied before the ischemia for 10 minutes. H₂S concentration was measured with an H₂S detecting electrochemical sensor from the coronary effluent solution. The 10 µM concentration was chosen for further experiments when the treatment with this solution was occurred after the ischemia. The release of H₂S is occurred by the hydrolyzing enzymes that are present in the heart endothelial cells. The protective effect of the new H₂S releasing ibuprofen molecule can be confirmed by the infarct sizes of hearts using the Triphenyl-tetrazolium chloride (TTC) staining method. Furthermore, we aimed to define the effect of the H₂S releasing ibuprofen derivative on autophagic and apoptotic processes in damaged hearts after investigating the molecular markers of these events by western blotting and immunohistochemistry techniques. Our further studies will include the examination of LC3I/II, p62, Beclin1, caspase-3, and other apoptotic molecules. We hope that confirming the protective effect of new H₂S releasing ibuprofen molecule will open a new possibility for the development of more effective cardioprotective agents with exerting fewer side effects. Acknowledgment: This study was supported by the grants of NKFIH- K-124719 and the European Union and the State of Hungary co- financed by the European Social Fund in the framework of GINOP- 2.3.2-15-2016-00043.

Keywords: autophagy, hydrogen sulfide, ibuprofen, ischemia, reperfusion

Procedia PDF Downloads 126

Authors: Ghazal Faraj, Andras Micsik

Abstract:

The CIDOC Conceptual Reference Model (CRM) is an extensible ontology that provides integrated access to heterogeneous and digital datasets. The CIDOC-CRM offers a “semantic glue” intended to promote accessibility to several diverse and dispersed sources of cultural heritage data. That is achieved by providing a formal structure for the implicit and explicit concepts and their relationships in the cultural heritage field. The COURAGE (“Cultural Opposition – Understanding the CultuRal HeritAGE of Dissent in the Former Socialist Countries”) project aimed to explore methods about socialist-era cultural resistance during 1950-1990 and planned to serve as a basis for further narratives and digital humanities (DH) research. This project highlights the diversity of flourished alternative cultural scenes in Eastern Europe before 1989. Moreover, the dataset of COURAGE is an online RDF-based registry that consists of historical people, organizations, collections, and featured items. For increasing the inter-links between different datasets and retrieving more relevant data from various data silos, a shared federated ontology for reconciled data is needed. As a first step towards these goals, a full understanding of the CIDOC CRM ontology (target ontology), as well as the COURAGE dataset, was required to start the work. Subsequently, the queries toward the ontology were determined, and a table of equivalent properties from COURAGE and CIDOC CRM was created. The structural diagrams that clarify the mapping process and construct queries are on progress to map person, organization, and collection entities to the ontology. Through mapping the COURAGE dataset to CIDOC-CRM ontology, the dataset will have a common ontological foundation with several other datasets. Therefore, the expected results are: 1) retrieving more detailed data about existing entities, 2) retrieving new entities’ data, 3) aligning COURAGE dataset to a standard vocabulary, 4) running distributed SPARQL queries over several CIDOC-CRM datasets and testing the potentials of distributed query answering using SPARQL. The next plan is to map CIDOC-CRM to other upper-level ontologies or large datasets (e.g., DBpedia, Wikidata), and address similar questions on a wide variety of knowledge bases.

Keywords: CIDOC CRM, cultural heritage data, COURAGE dataset, ontology alignment

Procedia PDF Downloads 125

Authors: Aphinan Phukaoluan, Surachai Dechkunakorn, Niwat Anuwongnukroh, Anak Khantachawana, Pongpan Kaewtathip, Julathep Kajornchaiyakul, Wassana Wichai

Abstract:

Aims: This study aims to address the amount of force delivered by a NiTiCu orthodontic wire with a ternary composition ratio of 46.0 Ni: 49.0 Ti: 5.0 Cu and to compare the results with a commercial NiTiCu 35 °C orthodontic archwire. Materials and Methods: Nickel (purity 99.9%), Titanium (purity 99.9%), and Copper (purity 99.9%) were used in this study with the atomic weight ratio 46.0 Ni: 49.0 Ti: 5.0 Cu. The elements were melted to form an alloy using an electrolytic arc furnace in argon gas atmosphere and homogenized at 800 °C for 1 hr. The alloys were subsequently sliced into thin plates (1.5mm) by EDM wire cutting machine to obtain the specimens and were cold-rolled with 30% followed by heat treatment in a furnace at 400 °C for 1 hour. Then, the three newly fabricated NiTiCu specimens were cut in nearly identical wire sizes of 0.016 inch x0.022 inch. Commercial preformed Ormco NiTiCu35 °C archwire with size 0.016 inch x 0.022 inches were used for comparative purposes. Three-point bending test was performed using a Universal Testing Machine to investigate the force of the load-deflection curve at oral temperature (36 °C+ 1) with deflection points at 0.25, 0.5, 0.75, 1.0. 1.25, and 1.5 mm. Descriptive statistics was used to evaluate each variables and independent t-test was used to analyze the differences between the groups. Results: Both NiTiCu wires presented typical superelastic properties as observed from the load-deflection curve. The average force was 341.70 g for loading, and 264.18 g for unloading for 46.0 Ni: 49.0 Ti: 5.0 Cu wire. Similarly, the values were 299.88 g for loading, and 201.96 g for unloading of Ormco NiTiCu35°C. There were significant differences (p < 0.05) in mean loading and unloading forces between the two NiTiCu wires. The deflection forces in loading and unloading force for Ormco NiTiCu at each point were less than 46.0 Ni: 49.0 Ti: 5.0 Cu wire, except at the deflection point of 0.25mm. Regarding the force difference between each deflection point of loading and unloading force, Ormco NiTiCu35 °C exerted less force than 46.0 Ni: 49.0 Ti: 5.0 Cu wire, except at difference deflection at 1.5-1.25 mm of unloading force. However, there were still within the acceptable limits for orthodontic use. Conclusion: The fabricated ternary alloy of 46.0 Ni: 49.0 Ti: 5.0 Cu (atomic weight) with 30% reduction and heat treatment at 400°C for 1 hr. and Ormco 35 °C NiTiCu presented the characteristics of the shape memory in their wire form. The unloading forces of both NiTiCu wires were in the range of orthodontic use. This should be a good foundation for further studies towards development of new orthodontic NiTiCu archwires.

Keywords: loading force, ternary alloy, NiTiCu, shape memory, orthodontic wire

Procedia PDF Downloads 264

Authors: Ketsada Sutthiumporn, Sittichot Thongkaw, Malee Santikunaporn

Abstract:

In Thailand, biodiesel has been utilized as an attractive substitute of petroleum diesel and the government imposes a mandatory biodiesel blending requirement in transport sector to improve energy security, support agricultural sector and reduce emissions. Though biodiesel blend has many advantages over diesel fuel such as improved lubricity, low sulfur content and higher flash point, there are still some technical problems such as oxidative stability, poor cold- flow properties and impurity. Such problems were related to the fatty acid composition in feedstock. Moreover, Thailand has announced the use of low sulfur diesel as a base diesel and will be continually upgrading to EURO 5 in 2023. With ultra low sulfur content, it may affect the diesel fuel properties especially lubricity as well. Therefore, in this study, the physical and chemical properties of palm oil-based biodiesel in low sulfur diesel blends from different producers will be investigated by standard methods per ASTM and EN. Also, its economic benefits based on diesel price structure in Thailand will be highlighted. The appropriate biodiesel blend ratio can affect the physico-chemical properties and reasonable price in the country. Properties of biodiesel, including specific gravity, kinematic viscosity, FAME composition, flash point, sulfur, water, oxidation stability and lubricity were measured by standard methods of ASTM and EN. The results show that the FAME composition of biodiesel has the fatty acid of C12:0 to C20:1, mostly in C16:0, C18:0, C18:1, and C18:2, which were main characteristic compositions of palm biodiesel. The physical and chemical properties of biodiesel blended diesel was found to be increases with an increasing amount of biodiesel such as specific gravity, flash point and kinematic viscosity while sulfur value was decreased. Moreover, in this study, the various properties of each biodiesel blends were plotted to determine the appropriate proportional range of biodiesel-blended diesel with an optimum fuel price.It can be seen that the amount of B100 can be filled from 1% up to 7% in which the quality was in accordance with Notification of the department of Energy business.The understanding of relation between physico-chemical properties of palm oil-based biodiesel and pricing is beneficial to guide the better development of desired feedstock in Thailand and to implement biodiesel blends with comparative price and diesel engine performance.

Keywords: fatty acid methyl ester, biodiesel, fuel price structure, palm oil in Thailand

Procedia PDF Downloads 92

Authors: Vered Holzmann, Ramzi Halabi

Abstract:

The current research investigates motivators and barriers to high-tech entrepreneurship in the Israeli-Arab Community. With the aim to exploit the capacity of Israel as a 'start-up nation', we identify the most important aspects to promote integration of Israeli-Arab entrepreneurs in high-tech startups and business companies, thus impact the socio-economic status of the Arab community in Israel. We reviewed the literature on the role of high-tech and entrepreneurship in the Israeli economy, the profile of the Israeli-Arab community with regard to education and employability, and the characteristics of minority entrepreneurship to understand entrepreneurs' intentions, their incentives to choose the entrepreneurial route on one hand and the obstacles that they face on the other hand. Based on the literature review, we conducted an integrated study that included a survey among 73 Israeli-Arabs involved in high-tech entrepreneurship and 16 semi-structured interviews with Israeli-Arab and Jewish entrepreneurs and leaders in the high-tech industry. We analyzed the data to explore personal and social motivating factors to entrepreneurship as well as educational and socio-economical barriers for entrepreneurship. Three major elements were found to be the most influential on Arab high-tech entrepreneurship in Israel: education, financial resources, and strategic-institutional support. The relationship between education and employability that is well-known with regard to general education, requires two additional aspects in the field of high-tech entrepreneurship: education of technology and engineering, and education of business and entrepreneurship. The study findings reveal that the main motivation factors for entrepreneurship are development of creative ideas and improvement of the socio-economic status, while financial-related factors and lack of institutional and governmental support are perceived as impediments to entrepreneurial activities. Financing difficulties are mainly derived from discriminating financial environment and lack of professional networking. The relationship between entrepreneurship and economic growth seems to be clear and simple; thus it is a national interest to encourage entrepreneurship among the Arab community, and especially high-tech entrepreneurship which has a significant role in the economic growth of Israel.

Keywords: high-tech industry, innovation management, Israeli-Arab community, minority entrepreneurship, motivating factors and barriers

Procedia PDF Downloads 196

Authors: A. O. Abulibdeh

Abstract:

The aim of this study is to investigate and compare the changes in the Land Surface Temperature (LST) as a function of urbanization, particularly land use/land cover changes, in three cities in the UAE, mainly Abu Dhabi, Dubai, and Al Ain. The scale of this assessment will be at the macro- and micro-levels. At the macro-level, a comparative assessment will take place to compare between the four cities in the UAE. At the micro-level, the study will compare between the effects of different land use/land cover on the LST. This will provide a clear and quantitative city-specific information related to the relationship between urbanization and local spatial intra-urban LST variation in three cities in the UAE. The main objectives of this study are 1) to investigate the development of LST on the macro- and micro-level between and in three cities in the UAE over two decades time period, 2) to examine the impact of different types of land use/land cover on the spatial distribution of LST. Because these three cities are facing harsh arid climate, it is hypothesized that (1) urbanization is affecting and connected to the spatial changes in LST; (2) different land use/land cover have different impact on the LST; and (3) changes in spatial configuration of land use and vegetation concentration over time would control urban microclimate on a city scale and control macroclimate on the country scale. This study will be carried out over a 20-year period (1996-2016) and throughout the whole year. The study will compare between two distinct periods with different thermal characteristics which are the cool/cold period from November to March and warm/hot period between April and October. The best practice research method for this topic is to use remote sensing data to target different aspects of natural and anthropogenic systems impacts. The project will follow classical remote sensing and mapping techniques to investigate the impact of urbanization, mainly changes in land use/land cover, on LST. The investigation in this study will be performed in two stages. Stage one remote sensing data will be used to investigate the impact of urbanization on LST on a macroclimate level where the LST and Urban Heat Island (UHI) will be compared in the three cities using data from the past two decades. Stage two will investigate the impact on microclimate scale by investigating the LST and UHI using a particular land use/land cover type. In both stages, an LST and urban land cover maps will be generated over the study area. The outcome of this study should represent an important contribution to recent urban climate studies, particularly in the UAE. Based on the aim and objectives of this study, the expected outcomes are as follow: i) to determine the increase or decrease of LST as a result of urbanization in these four cities, ii) to determine the effect of different land uses/land covers on increasing or decreasing the LST.

Keywords: land use/land cover, global warming, land surface temperature, remote sensing

Procedia PDF Downloads 230

Authors: Lorraine Joyce Chua, Sheena Fatima Ragas, Flora Mae Tantay, Carolyn Marie Sunio

Abstract:

The Philippines is one of the countries most affected by weather-related disasters. The occurrence of natural disasters in this country increases due to environmental degradation making environment preservation a growing trend in the society including the corporate world. Most organizations implemented green practices in order to lower expenses unaware that some of these practices were already a part of a new trend in human resource management known as Green Human Resource Management (GHRM). GHRM is when business organizations implement HR policies programs processes and techniques that bring environmental impact and sustainability practices on the organization. In relation to this, the study hypothesizes that implementing GHRM practices in the workplace will spillover to an employees lifestyle and such lifestyle may moderate the impact of GHRM practices to his job performance. Private industries located in the Philippines National Capital Region (NCR) were purposively selected for the purpose of this study. They must be ISO14001 certified or are currently aiming for such certification. The employee respondents were randomly selected and were asked to answer a reliable and valid researcher-made questionnaire. Structural equation modeling (SEM) supported the hypothesis that GHRM practices may spillover to employees lifestyle stimulating such individual to start a green lifestyle which moderates the impact of GHRM to his job performance. It can also be implied that GHRM practices help shape employees to become environmentally aware and responsible which may help them in preserving the environment. The findings of this study may encourage Human Resource practitioners to implement GHRM practices in the workplace in order to take part in sustaining the environment while maintaining or improving employees job performance and keeping them motivated. This study can serve as a basis for future research regarding the importance of strengthening the GHRM implementation here in the Philippines. Future studies may focus more on the impact of GHRM to other factors, such as job loyalty and job satisfaction of the employees belonging to specific industries which would greatly contribute to the GHRM community in the Philippines.

Keywords: GHRM practices, Green Human Resource Management, Green Lifestyle, ISO14001, job performance, Philippines

Procedia PDF Downloads 244

Authors: Akshay Rege, Lara Gomaa, Maneesh Kumar Verma, Sem Carree

Abstract:

The aim of this paper is to articulate design strategies and recommendations for introducing robots into the city life of people based on experiments conducted with robots and semi-autonomous systems in three cities in the Netherlands. This research was carried out by the Spot robotics team of Impact Lab housed within YES!Delft, a start-up accelerator located in Delft, The Netherlands. The premise of this research is to inform the development of the ‘region of the future’ by the Municipality of Rotterdam-Den Haag (MRDH). The paper starts by reporting the desktop research carried out to find and develop multiple use cases for robots to support humans in various activities. Further, the paper reports the user research carried out by crowdsourcing responses collected in public spaces of Rotterdam-Den Haag region and on the internet. Furthermore, based on the knowledge gathered in the initial research, practical experiments were carried out using robots and semi-autonomous systems in order to test and validate our initial research. These experiments were conducted in three cities in the Netherlands which were Rotterdam, The Hague, and Delft. Custom sensor box, Drone, and Boston Dynamics' Spot robot were used to conduct these experiments. Out of thirty use cases, five were tested with experiments which were skyscraper emergency evacuation, human transportation and security, bike lane delivery, mobility tracking, and robot drama. The learnings from these experiments provided us with insights into human-robot interaction and symbiosis in cities which can be used to introduce robots in cities to support human activities, ultimately enabling the transitioning from a human only city life towards a blended one where robots can play a role. Based on these understandings, we formulated design guidelines and strategy recommendations for incorporating robots in the Rotterdam-Den Haag’s region of the future. Lastly, we discuss how our insights in the Rotterdam-Den Haag region can inspire and inform the incorporation of robots in different cities of the world.

Keywords: city life, design guidelines, human-robot Interaction, robot use cases, robotic experiments, strategy recommendations, user research

Procedia PDF Downloads 74

Authors: Martin Tazky, Rudolf Hela, Lucia Osuska, Petr Novosad

Abstract:

Concrete’s volumetric changes are natural process caused by silicate minerals’ hydration. These changes can lead to cracking and subsequent destruction of cementitious material’s matrix. In most cases, cracks can be assessed as a negative effect of hydration, and in all cases, they lead to an acceleration of degradation processes. Preventing the formation of these cracks is, therefore, the main effort. Once of the possibility how to eliminate this natural concrete shrinkage process is by using different types of dispersed reinforcement. For this application of concrete shrinking, steel and polymer reinforcement are preferably used. Despite ordinarily used reinforcement in concrete to eliminate shrinkage it is possible to look at this specific problematic from the beginning by itself concrete mix composition. There are many secondary raw materials, which are helpful in reduction of hydration heat and also with shrinkage of concrete during curing. The new science shows the possibilities of shrinkage reduction also by the controlled formation of hydration products, which could act by itself morphology as a traditionally used dispersed reinforcement. This contribution deals with the possibility of controlled formation of mono- and tri-sulfate which are considered like degradation minerals. Mono- and tri- sulfate's controlled formation in a cementitious composite can be classified as a self-healing ability. Its crystal’s growth acts directly against the shrinking tension – this reduces the risk of cracks development. Controlled formation means that these crystals start to grow in the fresh state of the material (e.g. concrete) but stop right before it could cause any damage to the hardened material. Waste materials with the suitable chemical composition are very attractive precursors because of their added value in the form of landscape pollution’s reduction and, of course, low cost. In this experiment, the possibilities of using the fly ash from fluidized bed combustion as a mono- and tri-sulphate formation additive were investigated. The experiment itself was conducted on cement paste and concrete and specimens were subjected to a thorough analysis of physicomechanical properties as well as microstructure from the moment of mixing up to 180 days. In cement composites, were monitored the process of hydration and shrinkage. In a mixture with the used admixture of fluidized bed combustion fly ash, possible failures were specified by electronic microscopy and dynamic modulus of elasticity. The results of experiments show the possibility of shrinkage concrete reduction without using traditionally dispersed reinforcement.

Keywords: shrinkage, monosulphates, trisulphates, self-healing, fluidized fly ash

Procedia PDF Downloads 167

Authors: Muhammad Shahid Shah, Akram Maqbool, Samina Ashraf

Abstract:

Since start of this century, world has adopted inclusion as a trend in special education. To meet the challenges of inclusion response, the Punjab government has developed a progressive policy to implement inclusive education. The objectives of this research were to analyze the administration and implementation process by consideration on the management, student’s admission process, screening and assessment, adaptations in curriculum and instruction along with an evaluation, government and nonprofit organizations support. The sample consisted of 50 schools both public and private with a total of 3000 students, 9 percent of which (270) were students with disabilities. Among all the students with disabilities, 63 percent (170) were male and 37 percent (100) were female. The concluded remarks regarding management revealed that a large number of inclusive schools was lacking in terms of developing a certain model for inclusion, including the managerial breakup of staff, the involvement of stakeholders, and conducted frequent meetings. Many of schools are not able to restructure their school organizations due to lack of financial resources, consultations, and backup. As for as student’s admission/identification/assessment was concerned, only 12 percent schools applied a selection process regarding student admission, half of which used different procedures for disable candidates. Approximately 5 percent of inclusive schools had modified their curriculum, including a variety of standards. In terms of instruction, 25 percent of inclusive schools reported that they modified their instructional process. Only a few schools, however, provided special equipment for students with visual impairment, physical impairment, speech and hearing problems, students with mild intellectual disabilities, and autism. In a student evaluation, more than 45 percent reported that test items, administration, time allocations, and students’ reports were modified. For the primary board examination conducted by the Education Department of Government of Punjab, this number decreased dramatically. Finally, government and nonprofit organizations support in the forms of funding, coaching, and facilities were mostly provided by provincial governments and by Ghazali Education Trust.

Keywords: inclusion, identification, assessment, funding, facilities, evaluation

Procedia PDF Downloads 118

Authors: Kalina Alina Aidarovna, Khayrullina Yulia Sergeevna

Abstract:

The question of forming quality housing and living environment remains a vexed problem in the current situation of high-rise apartment building in big cities of Russia. At this start up stage of the modern so-called "mass housing" market it needs to identify key quality characteristics on a different scale from apartments to the district. This paper describes the methodology of qualitative assessment of modern mass housing construction, made on the basis of the ITMO university in cooperation with the institute of spatial planning "Urbanika," based on the case study of St. Petersburg’s residential mass housing built in 2011-2014. The methodology of the study of housing and living environment goes back to the native and foreign urbanists of 60s - 80s, such Jane Jacobs, Jan Gehl, Oscar Newman, Krasheninnikov, as well as Sommer, Stools, Kohnen and Sherrod, Krasilnikova, Sychev, Zhdanov, Tinyaeva considering spatial features of living environment in a wide range of its characteristics (environmental control, territorial and personalization, privacy, etc.). Assessment is carrying out on the proposed system of criteria developed for each residential environment scale-district, quarter, courtyard, building surrounding grounds, houses, and flats. Thus the objects of study are planning unit of residential development areas (residential area, neighborhood, quarter) residential units areas (living artist, a house), and households (apartments) consisting of residential units. As a product of identified methodology, after the results of case studies of more than 700 residential complexes in St. Petersburg, we intend the creation of affordable online resource that would allow conducting a detailed qualitative evaluation or comparative characteristics of residential complexes for all participants of the construction market-developers, designers, realtors and buyers. Thereby the main objective of the rating may be achieved to improve knowledge, requirements, and demand for quality housing and living environment among the major stakeholders of the construction market.

Keywords: methodology of living environment, qualitative assessment of mass housing, scale-district, vexed problem

Procedia PDF Downloads 438

Authors: Jia-Chao Wang

Abstract:

The cosmic microwave background radiation (CMB) freed during the recombination era can be considered as a photon source of small duration; a one-time event happened everywhere in the universe simultaneously. If space is divided into concentric shells centered at an observer’s location, one can imagine that the CMB photons originated from the nearby shells would reach and pass the observer first, and those in shells farther away would follow as time goes forward. In the Big Bang model, space expands rapidly in a time-dependent manner as described by the scale factor. This expansion results in an event horizon coincident with one of the shells, and its radius can be calculated using cosmological calculators available online. Using Planck 2015 results, its value during the recombination era at cosmological time t = 0.379 million years (My) is calculated to be Revent = 56.95 million light-years (Mly). The event horizon sets a boundary beyond which the freed CMB photons will never reach the observer. The photons within the event horizon also exhibit a peculiar behavior. Calculated results show that the CMB observed today was freed in a shell located at 41.8 Mly away (inside the boundary set by Revent) at t = 0.379 My. These photons traveled 13.8 billion years (Gy) to reach here. Similarly, the CMB reaching the observer at t = 1, 5, 10, 20, 40, 60, 80, 100 and 120 Gy are calculated to be originated at shells of R = 16.98, 29.96, 37.79, 46.47, 53.66, 55.91, 56.62, 56.85 and 56.92 Mly, respectively. The results show that as time goes by, the R value approaches Revent = 56.95 Mly but never exceeds it, consistent with the earlier statement that beyond Revent the freed CMB photons will never reach the observer. The difference Revert - R can be used as a measure of the remaining observable CMB photons. Its value becomes smaller and smaller as R approaching Revent, indicating a dwindling supply of the observable CMB radiation. In this paper, detailed dwindling effects near the event horizon are analyzed with the help of online cosmological calculators based on the lambda cold dark matter (ΛCDM) model. It is demonstrated in the literature that assuming the CMB to be a blackbody at recombination (about 3000 K), then it will remain so over time under cosmological redshift and homogeneous expansion of space, but with the temperature lowered (2.725 K now). The present result suggests that the observable CMB photon density, besides changing with space expansion, can also be affected by the dwindling supply associated with the event horizon. This raises the question of whether the blackbody of CMB at recombination can remain so over time. Being able to explain the blackbody nature of the observed CMB is an import part of the success of the Big Bang model. The present results cast some doubts on that and suggest that the model may have an additional challenge to deal with.

Keywords: blackbody of CMB, CMB radiation, dwindling supply of CMB, event horizon

Procedia PDF Downloads 102

Authors: Stamatis Zoras, Vasilis Evagelopoulos, Theodoros Staurakas

Abstract:

The association between elevated air pollution levels and extreme climate conditions (temperature, particulate matter, ozone levels, etc.) and mental consequences has been, recently, the focus of significant number of studies. It varies depending on the time of the year it occurs either during the hot period or cold periods but, specifically, when extreme air pollution and weather events are observed, e.g. air pollution episodes and persistent heatwaves. It also varies spatially due to different effects of air quality and climate extremes to human health when considering metropolitan or rural areas. An air pollutant concentration and a climate extreme are taking a different form of impact if the focus area is countryside or in the urban environment. In the built environment the climate extreme effects are driven through the formed microclimate which must be studied more efficiently. Variables such as biological, age groups etc may be implicated by different environmental factors such as increased air pollution/noise levels and overheating of buildings in comparison to rural areas. Gridded air quality and climate variables derived from the land surface observations network of West Macedonia in Greece will be analysed against mortality data in a spatial format in the region of West Macedonia. Artificial intelligence (AI) tools will be used for data correction and prediction of health deterioration with climatic conditions and air pollution at local scale. This would reveal the built environment implications against the countryside. The air pollution and climatic data have been collected from meteorological stations and span the period from 2000 to 2009. These will be projected against the mortality rates data in daily, monthly, seasonal and annual grids. The grids will be operated as AI-based warning models for decision makers in order to map the health conditions in rural and urban areas to ensure improved awareness of the healthcare system by taken into account the predicted changing climate conditions. Gridded data of climate conditions, air quality levels against mortality rates will be presented by AI-analysed gridded indicators of the implicated variables. An Al-based gridded warning platform at local scales is then developed for future system awareness platform for regional level.

Keywords: air quality, artificial inteligence, climatic conditions, mortality

Procedia PDF Downloads 88

Authors: David Nchinda Keming

Abstract:

The present study is focused on both the national and international collective fight against Boko Haram terrorism on Cameroon and the rule played by the Lake Chad Basin Countries (LCBCs) and the global community to suffocate the sect’s activities in the region. Although countries of the Lake Chad Basin include: Cameroon, Chad, Nigeria and Niger others like Benin also joined the course. The justification for the internationalisation of the fight against Boko Haram could be explained by the ecological and international climatic importance of the Lake Chad and the danger posed by the sect not only to the Lake Chad member countries but to global armed, civil servants and the international political economy. The study, therefore, kick start with Cameroon’s reaction to Boko Haram’s terrorist attacks on its territory. It further expounds on Cameroon’s request on bilateral diplomacy from members of the UN Security Council for an international collective support to staple the winds of the challenging sect. The study relies on the hypothesis that Boko Haram advanced terrorism on Cameroon was more challenging to the domestic military intelligence thus forcing the government to seek for bilateral and multilateral international collective support to secure its territory from the powerful sect. This premise is tested internationally via (multilateral cooperation, bilateral response, regional cooperation) and domestically through (solidarity parade, religious discourse, political manifestations, war efforts, the vigilantes and the way forward). To accomplish our study, we made used of the mixed research methodologies to interpret the primary, secondary and tertiary sources consulted. Our results reveal that the collective response was effectively positive justified by the drastic drop in the sect’s operations in Cameroon and the whole LCBCs. Although the sect was incapacitated, terrorism remains an international malaise and Cameroon hosts a fertile ground for terrorists’ activism. Boko Haram was just weakened and not completely defeated and could reappear someday even under a different appellation. Therefore, to absolutely eradicate terrorism in general and Boko Haram in particular, LCBCs must improve their military intelligence on terrorism and continue to collaborate with advanced experienced countries in fighting terrorism.

Keywords: Boko Haram, terrorism, domestic, international, response

Procedia PDF Downloads 136

Authors: Surinder Pal, Ajay Gupta, Johny Khajuria

Abstract:

Casting simulation helps visualize mold filling and casting solidification; predict related defects like cold shut, shrinkage porosity and hard spots; and optimize the casting design to achieve the desired quality with high yield. Flow and solidification of molten metals are, however, a very complex phenomenon that is difficult to simulate correctly by conventional computational techniques, especially when the part geometry is intricate and the required inputs (like thermo-physical properties and heat transfer coefficients) are not available. Simulation software is based on the process of modeling a real phenomenon with a set of mathematical formulas. It is, essentially, a program that allows the user to observe an operation through simulation without actually performing that operation. Simulation software is used widely to design equipment so that the final product will be as close to design specs as possible without expensive in process modification. Simulation software with real-time response is often used in gaming, but it also has important industrial applications. When the penalty for improper operation is costly, such as airplane pilots, nuclear power plant operators, or chemical plant operators, a mockup of the actual control panel is connected to a real-time simulation of the physical response, giving valuable training experience without fear of a disastrous outcome. The all casting simulation software has own requirements, like magma cast has only best for crack simulation. The latest generation software Auto CAST developed at IIT Bombay provides a host of functions to support method engineers, including part thickness visualization, core design, multi-cavity mold design with common gating and feeding, application of various feed aids (feeder sleeves, chills, padding, etc.), simulation of mold filling and casting solidification, automatic optimization of feeders and gating driven by the desired quality level, and what-if cost analysis. IIT Bombay has developed a set of applications for the foundry industry to improve casting yield and quality. Casting simulation is a fast and efficient solution for process for advanced tool which is the result of more than 20 years of collaboration with major industrial partners and academic institutions around the world. In this paper the process of casting simulation is studied.

Keywords: casting simulation software’s, simulation technique’s, casting simulation, processes

Procedia PDF Downloads 461

Authors: Željka Rogač, Dejan Stevanović, Sara Bečanović, Ljubica Božić, Aleksandar Dimitrijević, Dragana Bogićević, Dimitrije Nikolić

Abstract:

Children with epilepsy face changes in cognitive functioning, the appearance of symptoms of psychopathology and a decline in their quality of life. Factors related to epileptic seizures and the side effects of AEDs are considered to be potential causes of these changes.These changes can be prevented by prompt action, replacement of AEDs, psychological and psychiatric treatment, and social support. However, a review of literature has not yielded a conclusion as to when it is best to react, i.e., when changes in the functioning of children with newly-diagnosed epilepsy appears. The primary goal of this study was to investigate the impact of the most commonly used AEDs on cognitive status, behavior, anxiety and depression, as well as quality of life of children with newly-diagnosed epilepsy, during the first six months of treatment. This is a non-interventional, prospective study involving six-month monitoring of cognitive status, internalizing and externalizing symptoms, as well as quality of life of children with newly-diagnosed epilepsy, and the impact of antiepileptic drugs on these domains. Children with new-onset epilepsy and their parents, immediately after the introduction of antiepileptic drugs as well as six months later, filled out appropriate questionnaires (RCADS, NCBRF, CHEQOL-25, KIDSCREEN-10, AEP). At the same time, a psychologist performed the psychological testing of the child (REVISK). At the very beginning of REVISK treatment, a reduced VIQ was established, while after six months there was a significant decrease in IQ, VIQ and especially PIQ, under the influence of primary cognitive potentials and the development of depressive symptoms. All scores of the RCADS and NCBFR questionnaires were significantly elevated after six months while internalizing and externalizing symptoms affected each other. The development of depressive symptoms was significantly influenced by AED. The scores of the CHEQOL25 and KIDSCREEN10 questionnaires were significantly reduced, influenced by the adverse effects of AED and quality of life at the start of treatment. Side effects of AEDs, were significantly associated with depressive symptoms and reduced quality of life and did not significantly affect cognitive decline, anxiety, ADHD, and behavioral disorders during the first six months.

Keywords: epilepsy, children, AEDs, cognition, behavior, ADHD, anxiety, depression, QOL

Procedia PDF Downloads 70

Authors: Rhea Khosla, Victoria Tzortziou-Brown

Abstract:

Introduction: Adolescent SRH has been neglected since the start of the millennium. Adolescents comprise 16% of the global population, with the largest proportion living in Asia (650 million). By late adolescence, individuals in these regions are likely to become sexually active, and thus they must understand their SRH rights. Many lack knowledge of SRH, using unreliable sources for such information. Sex education is necessary to standardize and inform sexual knowledge, which empowers adolescents to make informed SRH decisions. School is an appropriate environment for this, however, SRH education requires effective policy to enforce. Nonetheless, this issue remains of low political priority in Asia and Africa. Current literature on sex education policy in schools in these regions is scarce and tends to have broad aims. Thus, a scoping review was necessary. Methods: Literature searches were conducted in February 2023 using six databases, including grey literature databases (PubMed, Scopus, Embase, Web of Science, Google Scholar, Global Index Medicus), returning a total of 1537 unique articles. After screening titles, abstracts and full text, 17 articles remained. References of included articles were additionally searched, producing a further 7 articles, which then underwent thematic analysis Results: Most countries in Africa and Asia did not have studies on this topic. Studies derived data from interviews with key stakeholders and quantitative methods quantified questionnaire responses. Barriers were: policy/curriculum issues, societal opinions, teaching discomfort, and lack of educator training. Limitations were insufficient timing, inconsistent implementation, insufficient hours dedicated to teaching, education received late into schooling, and discrepancies between teachers, schools, and students about whether policies were being implemented. Discussion: Based on the existing limited evidence, a cultural shift to reduce stigma seems necessary, alongside teacher and student involvement in policy formulation with effective implementation monitoring and educator training.

Keywords: adolescent, Africa, Asia, education, sexual and reproductive health, policy

Procedia PDF Downloads 31

Authors: Sreelekha Prakash, Yulong Gu

Abstract:

Background: About 61% of adults surveyed across 25 states reported they had experienced at least one type of Adverse Childhood Experience (ACE) before 18 years of age. Relationships between ACEs and a variety of substance-related behaviors and behavioral health have been reported in previous studies. ACEs can have lasting, negative effects on health, well-being, as well as life opportunities such as education and job potential. Objectives: For the current research, the aim was to assess the factors affecting substance use behavior in young adults. The further onset of drug use and its association was analyzed with ACEs and mental health. Method: The young adults from a county in the north-eastern United States were invited to participate in an online questionnaire survey with prior consent through an IRB approved study. The Survey included questions related to social determinants of health, 10 item ACE questionnaire, and substance use related to Alcohol, Marijuana, Opioids, Stimulants, and other drugs. PHQ-9 questionnaire was used to assess cognitive health. Results: Data was analyzed for the 244 completed surveys {68% (165) were females, and 78% (190) were Whites}. The average age of the participants was 26.7 years, and approximately 80% were lifelong residents of the county or year-round residents. Of the respondents, 50% (122) were high school graduates with some college education, and 56% (136) had a full-time jobs. Past 30-day usage for alcohol was 76% (72), and marijuana was 28.4% (27). The data showed that the higher the ACE scores, the younger they start using any substance (p < 0.0001). The data for PHQ-9 and ACE scores showed that the higher the ACE score, the higher the PHQ-9 score, with a significant p-value (p 0.0001). The current data also showed a significant association with other drugs; marijuana use showed significance for 30 days of use (p 0.0001), stimulant use (0.0008), prescription drug misuse (0.01), and opioids (0.01). Conclusion: These findings further support the association between ACEs and initiation of drug use and its correlation with mental health symptoms. Promoting a safe and supportive environment for children and youth in their earlier ages can prevent the youth and young adults from the effects of drug use and create healthy living habits for young adults.

Keywords: subtance use, young adults, adverse childhood experience, PHQ-9

Procedia PDF Downloads 65

Authors: Zeineb Yousse, Fakher Kharrat

Abstract:

Mosaic is a part of a broad universal cultural heritage; sometimes it represents a rather essential source for the researches on the everyday life of some of the previous civilizations. Tunisia has one of the finest and largest collections of mosaics in the world, which is essentially exhibited in the Museums of Bardo and Sousse. Restored and reconstituted, they bear witnesses to hard work. Our paper deals with the discipline of conservation of Roman mosaics based on the proceedings of the workshop of the Museum of Sousse. Thus, we highlight two main objectives. In the first place, it is a question of revealing the techniques adopted by professionals to handle mosaics and to which school of conservation these techniques belong. In the second place, we are going to interpret the works initiated to preserve the archaeological heritage in order to protect it in present time and transmit it to future generations. To this end, we paid attention to four Roman mosaics currently exhibited in the Museum of Sousse. These Mosaics show different voids or gaps at the level of their surfaces and the method used to fill these gaps seems to be interesting to analyze. These mosaics are known under the names of: Orpheus Charming the Animals, Gladiator and Bears, Stud farm of Sorothus and finally Head of Medusa. The study on the conservation passes through two chained phases. We start with a small historical overview in order to gather information related to the original location, the date of its composition as well as the description of its image. Afterward, the intervention process is analyzed by handling three complementary elements which are: diagnosis of the existing state, the study of the medium processing and the study of the processing of the tesselatum surface which includes the pictorial composition of the mosaic. Furthermore, we have implemented an evaluation matrix with six operating principles allowing the assessment of the appropriateness of the intervention. These principles are the following: minimal intervention, reversibility, compatibility, visibility, durability, authenticity and enhancement. Various accumulated outcomes are pointing out the techniques used to fill the gaps as well as the level of compliance with the principles of conservation. Accordingly, the conservation of mosaics in Tunisia is a practice that combines various techniques without really arguing about the choice of a particular theory.

Keywords: conservation, matrix, museum of Sousse, operating particular theory, principles, Roman mosaics

Procedia PDF Downloads 307

Authors: Sharon Q. Yang, Robert J. Congleton

Abstract:

Information security is a broad concept that covers any issues and concerns about the proper access and use of information on the Internet, including measures and procedures to protect intellectual property and private data from illegal access and online theft; the act of hacking; and any defensive technologies that contest such cybercrimes. As more research and commercial activities are conducted online, cybercrimes have increased significantly, putting sensitive information at risk. Information security has become critically important for organizations and private citizens alike. Hackers scan for network vulnerabilities on the Internet and steal data whenever they can. Cybercrimes disrupt our daily life, cause financial losses, and instigate fear in the public. Since the start of the pandemic, most data related cybercrimes targets have been either financial or health information from companies and organizations. Libraries also should have a high interest in understanding and adopting information security methods to protect their patron data and copyrighted materials. But according to information security professionals, higher education and cultural organizations, including their libraries, are the least prepared entities for cyberattacks. One recent example is that of Steven’s Institute of Technology in New Jersey in the US, which had its network hacked in 2020, with the hackers demanding a ransom. As a result, the network of the college was down for two months, causing serious financial loss. There are other cases where libraries, colleges, and universities have been targeted for data breaches. In order to build an effective defense, we need to understand the most common types of cybercrimes, including phishing, whaling, social engineering, distributed denial of service (DDoS) attacks, malware and ransomware, and hacker profiles. Our research will focus on each hacking technique and related defense measures; and the social background and reasons/purpose of hacker and hacking. Our research shows that hacking techniques will continue to evolve as new applications, housing information, and data on the Internet continue to be developed. Some cybercrimes can be stopped with effective measures, while others present challenges. It is vital that people understand what they face and the consequences when not prepared.

Keywords: cybercrimes, hacking technologies, higher education, information security, libraries

Procedia PDF Downloads 110

Authors: Sushil Pradhan

Abstract:

Biotechnology contributes to sustainable development in several ways such as biofertilizer production, biopesticide production and management of environmental pollution, tissue culture and biodiversity conservation in vitro, in vivo and in situ, Insectivorous medicinal plant Drosera burmannii Vahl belongs to the Family-Droseraceae under Order-Caryophyllales, Dicotyledoneae, Angiospermeae which has 31 (thirty one) living genera and 194 species besides 7 (seven) extinct (fossil) genera. Locally it is known as “Patkanduri” in Odia. Its Hindi name is “Mukhajali” and its English name is “Sundew”. The earliest species of Drosera was first reported in 1753 by Carolous Linnaeus called Drosera indica L (Indian Sundew). The latest species of Drosera reported by Fleisch A, Robinson, AS, McPherson S, Heinrich V, Gironella E and Madulida D.A. (2011) is Drosera ultramafica from Malaysia. More than 50 % species of Drosera have been reported from Australia and next to Australia is South Africa. India harbours only 3 species such as D. indica L, Drosera burmannii Vahl and D. peltata L. From our Odisha only D. burmannii Vahl is being reported for the first time from the district of Subarnapur near Sonepur (Arjunpur Reserve Forest Area). Drosera plant is autotrophic but to supplement its Nitrogen (N2) requirement it adopts heterotrophic mode of nutrition (insectivorous/carnivorous) as well. The colour of plant in mostly red and about 20-30cm in height with beautiful pink or white pentamerous flowers. Plants grow luxuriantly during November to February in shady and moist places near small water bodies of running water stream. Medicinally it is a popular herb in the locality for the treatment of cold and cough in children in rainy season by the local Doctors (Kabiraj and Baidya). In the present field investigation an attempt has been made to understand the unique reproductive phase and life cycle of the plant thereby planning for its conservation and propagation through various techniques of tissue culture and biotechnology. More importantly besides morphological and anatomical studies, cytological investigation is being carried out to find out the number of chromosomes in the cell and its genomics as there is no such report as yet for Drosera burmannii Vahl. The ecological significance and biodiversity conservation of Drosera with special reference to energy, environmental and chemical engineering has been discussed in the research paper presentation.

Keywords: insectivorous, medicinal, drosera, biotechnology, chromosome, genome

Procedia PDF Downloads 364

Authors: Nathaniel Evans, Jessica Boersma, Kenneth Kass

Abstract:

With technology and STEM fields growing every day, there is a significant projected shortfall in qualified cybersecurity workers. As such, it is essential to develop a cybersecurity curriculum that builds skills and cultivates interest in cybersecurity early on. With new jobs being created every day and an already significant gap in the job market, it is vital that educators are pro-active in introducing a cybersecurity curriculum where students are able to learn new skills and engage in an age-appropriate cyber curriculum. Within this growing world of cybersecurity, students should engage in age-appropriate technology and cybersecurity curriculum, starting with elementary school (k-5), extending through high school, and ultimately into college. Such practice will provide students with the confidence, skills, and, ultimately, the opportunity to work in the burgeoning information security field. This paper examines educational methods, pedagogical practices, current cybersecurity curricula, and other educational resources and conducts analysis for false assumptions and developmental appropriateness. It also examines and identifies common mistakes with current cyber curriculum and lessons and discuss strategies for improvement. Throughout the lessons that were reviewed, many common mistakes continued to pop up. These mistakes included age appropriateness, technology resources that were available, and consistency of student’s skill levels. Many of these lessons were written for the wrong grade levels. The ones written for the elementary level all had activities that assumed that every student in the class could read at grade level and also had background knowledge of the cyber activity at hand, which is not always the case. Another major mistake was that these lessons assumed that all schools had any kind of technology resource available to them. Some schools are 1:1, and others are only allotted three computers in their classroom where the students have to share. While coming up with a cyber-curriculum, it has to be kept in mind that not all schools are the same, not every classroom is the same. There are many students who are not reading at their grade level or have not had exposure to the digital world. We need to start slow and ease children into the cyber world. Once they have a better understanding, it will be easier to move forward with these lessons and get the students engaged. With a better understanding of common mistakes that are being made, a more robust curriculum and lessons can be created that no only spark a student’s interest in this much-needed career field but encourage learning while keeping our students safe from cyber-attacks.

Keywords: assumptions, cybersecurity, k-12, teacher

Procedia PDF Downloads 147

Authors: Suchart Tripopsakul

Abstract:

This paper uses data from the Global Entrepreneurship Monitor (GEM) to investigate the difference of attitudes towards entrepreneurial intention (EI). EI is generally assumed to be the single most relevant predictor of entrepreneurial behavior. The aim of this paper is to examine a range of attitudes effect on individual’s intent to start a new venture. A cross-cultural comparison between Asia and Europe is used to further investigate the possible differences between potential entrepreneurs from these distinct national contexts. The empirical analysis includes a GEM data set of 10 countries (n = 10,306) which was collected in 2013. Logistic regression is used to investigate the effect of individual’s attitudes on EI. Independent variables include individual’s perceived capabilities, the ability to recognize business opportunities, entrepreneurial network, risk perceptions as well as a range of socio-cultural attitudes. Moreover, a cross-cultural comparison of the model is conducted including six ASEAN (Malaysia, Indonesia, Philippines, Singapore, Vietnam and Thailand) and four European nations (Spain, Sweden, Germany, and the United Kingdom). The findings support the relationship between individual’s attitudes and their entrepreneurial intention. Individual’s capability, opportunity recognition, networks and a range of socio-cultural perceptions all influence EI significantly. The impact of media attention on entrepreneurship and was found to influence EI in ASEAN, but not in Europe. On the one hand, Fear of failure was found to influence EI in Europe, but not in ASEAN. The paper develops and empirically tests attitudes toward Entrepreneurial Intention between ASEAN and Europe. Interestingly, fear of failure was found to have no significant effect in ASEAN, and the impact of media attention on entrepreneurship and was found to influence EI in ASEAN. Moreover, the resistance of ASEAN entrepreneurs to the otherwise high rates of fear of failure and high impact of media attention are proposed as independent variables to explain the relatively high rates of entrepreneurial activity in ASEAN as reported by GEM. The paper utilizes a representative sample of 10,306 individuals in 10 countries. A range of attitudes was found to significantly influence entrepreneurial intention. Many of these perceptions, such as the impact of media attention on entrepreneurship can be manipulated by government policy. The paper also suggests strategies by which Asian economy in particular can benefit from their apparent high impact of media attention on entrepreneurship.

Keywords: an entrepreneurial intention, attitude, GEM, ASEAN and Europe

Procedia PDF Downloads 281

Authors: Hyun-Ju Oh, Soon-Rim Suh, Mihan Kim

Abstract:

The steady and rapid increase of the older population is a global phenomenon. Chronic diseases and disabilities are increased due to aging. In general, exercise has been known to be most effective in preventing and managing chronic back pain. However, it is hard for the older women to initiate and maintain the exercise. Transtheoretical model (TTM) is one of the theories explain behavioral changes such as exercise. The application of the program considering the stage of behavior change is effective for the elderly woman to start and maintain the exercise. The purpose of this study was to develop TTM based exercise program and to examine its effect for elderly women with chronic back-pain. For the program evaluation, the non-equivalent control pre-posttest design was applied. The independent variable of this study is exercise intervention program. The contents of the program were constructed considering the characteristics of the elderly women with chronic low back pain, focusing on the process of change, the stage of change by the previous studies. The developed exercise program was applied to the elderly women with chronic low back pain in the planning stage and the preparation stage. The subjects were 50 older women over 65 years of age with chronic back-pain who did not practice regular exercise. The experimental group (n=25) received the 8weeks TTM based exercise program. The control group received the book which named low back pain management. Data were collected at three times: before the exercise intervention, right after the intervention, and 4weeks after the intervention. The dependent variables were the processes of change, decisional balance, exercise self-efficacy, back-pain, depression and muscle strength. The results of this study were as follows. Processes of change (<.001), pros of decisional balance (<.001), exercise self-efficacy (<.001), back pain (<.001), depression (<.001), muscle strength (<.001) were higher in the experimental group than in the control group right after the program and 4weeks after the programs. The results of this study show that applying the TTM based exercise program increases the use of the change process, increases the exercise self-efficacy, increases the stage of changing the exercise behavior and strengthens the muscular strength by lowering the degree of pain and depression Respectively. The significance of the study was to confirm the effect of continuous exercise by maintaining regular exercise habits by applying exercise program of the transtheoretical model to the chronic low back pain elderly with exercise intention.

Keywords: chronic back pain, elderly, exercise, women

Procedia PDF Downloads 241

Authors: Simon B. N. Thompson

Abstract:

Early indicator of neurological disease has been proposed by the expanded Thompson Cortisol Hypothesis which suggests that yawning is linked to rises in cortisol levels. Cortisol is essential to the regulation of the immune system and pathological yawning is a symptom of multiple sclerosis (MS). Electromyography activity (EMG) in the jaw muscles typically rises when the muscles are moved – extended or flexed; and yawning has been shown to be highly correlated with cortisol levels in healthy people. It is likely that these elevated cortisol levels are also seen in people with MS. The possible link between EMG in the jaw muscles and rises in saliva cortisol levels during yawning were investigated in a randomized controlled trial of 60 volunteers aged 18-69 years who were exposed to conditions that were designed to elicit the yawning response. Saliva samples were collected at the start and after yawning, or at the end of the presentation of yawning-provoking stimuli, in the absence of a yawn, and EMG data was additionally collected during rest and yawning phases. Hospital Anxiety and Depression Scale, Yawning Susceptibility Scale, General Health Questionnaire, demographic, and health details were collected and the following exclusion criteria were adopted: chronic fatigue, diabetes, fibromyalgia, heart condition, high blood pressure, hormone replacement therapy, multiple sclerosis, and stroke. Significant differences were found between the saliva cortisol samples for the yawners, t (23) = -4.263, p = 0.000, as compared with the non-yawners between rest and post-stimuli, which was non-significant. There were also significant differences between yawners and non-yawners for the EMG potentials with the yawners having higher rest and post-yawning potentials. Significant evidence was found to support the Thompson Cortisol Hypothesis suggesting that rises in cortisol levels are associated with the yawning response. Further research is underway to explore the use of cortisol as a potential diagnostic tool as an assist to the early diagnosis of symptoms related to neurological disorders. Bournemouth University Research & Ethics approval granted: JC28/1/13-KA6/9/13. Professional code of conduct, confidentiality, and safety issues have been addressed and approved in the Ethics submission. Trials identification number: ISRCTN61942768. http://www.controlled-trials.com/isrctn/

Keywords: cortisol, electromyography, neurology, yawning

Procedia PDF Downloads 564

Authors: M. Amanipour, J. Towfighi, E. Ganji Babakhani, M. Heidari

Abstract:

Cylindrical alumina microfiltration membrane (GMITM Corporation, inside diameter=9 mm, outside diameter=13 mm, length= 50 mm) with an average pore size of 0.5 micrometer and porosity of about 0.35 was used as the support for membrane reactor. This support was soaked in boehmite sols, and the mean particle size was adjusted in the range of 50 to 500 nm by carefully controlling hydrolysis time, and calcined at 650 °C for two hours. This process was repeated with different boehmite solutions in order to achieve an intermediate layer with an average pore size of about 50 nm. The resulting substrate was then coated with a thin and dense layer of silica by counter current chemical vapour deposition (CVD) method. A boehmite sol with 10 wt.% of nickel which was prepared by a standard procedure was used to make the catalytic layer. BET, SEM, and XRD analysis were used to characterize this layer. The catalytic membrane reactor was placed in an experimental setup to evaluate the permeation and hydrogen separation performance for a steam reforming reaction. The setup consisted of a tubular module in which the membrane was fixed, and the reforming reaction occurred at the inner side of the membrane. Methane stream, diluted with nitrogen, and deionized water with a steam to carbon (S/C) ratio of 3.0 entered the reactor after the reactor was heated up to 500 °C with a specified rate of 2 °C/ min and the catalytic layer was reduced at presence of hydrogen for 2.5 hours. Nitrogen flow was used as sweep gas through the outer side of the reactor. Any liquid produced was trapped and separated at reactor exit by a cold trap, and the produced gases were analyzed by an on-line gas chromatograph (Agilent 7890A) to measure total CH₄ conversion and H₂ permeation. BET analysis indicated uniform size distribution for catalyst with average pore size of 280 nm and average surface area of 275 m².g^-1. Single-component permeation tests were carried out for hydrogen, methane, and carbon dioxide at temperature range of 500-800 °C, and the results showed almost the same permeance and hydrogen selectivity values for hydrogen as the composite membrane without catalytic layer. Performance of the catalytic membrane was evaluated by applying membranes as a membrane reactor for methane steam reforming reaction at gas hourly space velocity (GHSV) of 10,000 h⁻¹ and 2 bar. CH₄ conversion increased from 50% to 85% with increasing reaction temperature from 600 °C to 750 °C, which is sufficiently above equilibrium curve at reaction conditions, but slightly lower than membrane reactor with packed nickel catalytic bed because of its higher surface area compared to the catalytic layer.

Keywords: catalytic membrane, hydrogen, methane steam reforming, permeance

Procedia PDF Downloads 239