Search results for: gender dynamics

Authors: Ahmed Borg, Elsa Aristodemou, Attia Attia

Abstract:

Well control involves managing the circulating drilling fluid within the wells and avoiding kicks and blowouts as these can lead to losses in human life and drilling facilities. Current practices for good control incorporate predictions of pressure losses through computational models. Developing a realistic hydraulic model for a good control problem is a very complicated process due to the existence of a complex multiphase region, which usually contains a non-Newtonian drilling fluid and the miscibility of formation gas in drilling fluid. The current approaches assume an inaccurate flow fluid model within the well, which leads to incorrect pressure loss calculations. To overcome this problem, researchers have been considering the more complex two-phase fluid flow models. However, even these more sophisticated two-phase models are unsuitable for applications where pressure dynamics are important, such as in managed pressure drilling. This study aims to develop and implement new fluid flow models that take into consideration the miscibility of fluids as well as their non-Newtonian properties for enabling realistic kick treatment. furthermore, a corresponding numerical solution method is built with an enriched data bank. The research work considers and implements models that take into consideration the effect of two phases in kick treatment for well control in conventional drilling. In this work, a corresponding numerical solution method is built with an enriched data bank. Software STARCCM+ for the computational studies to study the important parameters to describe wellbore multiphase flow, the mass flow rate, volumetric fraction, and velocity of each phase. Results showed that based on the analysis of these simulation studies, a coarser full-scale model of the wellbore, including chemical modeling established. The focus of the investigations was put on the near drill bit section. This inflow area shows certain characteristics that are dominated by the inflow conditions of the gas as well as by the configuration of the mud stream entering the annulus. Without considering the gas solubility effect, the bottom hole pressure could be underestimated by 4.2%, while the bottom hole temperature is overestimated by 3.2%. and without considering the heat transfer effect, the bottom hole pressure could be overestimated by 11.4% under steady flow conditions. Besides, larger reservoir pressure leads to a larger gas fraction in the wellbore. However, reservoir pressure has a minor effect on the steady wellbore temperature. Also as choke pressure increases, less gas will exist in the annulus in the form of free gas.

Keywords: multiphase flow, well- control, STARCCM+, petroleum engineering and gas technology, computational fluid dynamic

Procedia PDF Downloads 117

Authors: Barnali Thakuria, Labananda Choudhury

Abstract:

Gender equality and women’s empowerment is one of the components of eight Millennium Development Goal (MDG).Literacy and employment are the parameters which reflect the empowerment of women. But in a developing country like India, literacy and working status among the females are not satisfactory. Both literacy and employment technically can be measured by Literate Life Expectancy (LLE) and Working Life Expectancy (WLE).One can also combine both the factors literacy and working to get a better new measure. The proposed indicator can be called literate-working life expectancy (LWLE). LLE gives an average number of years a person lives in a literate state under current mortality and literacy conditions while WLE defined as average number of years a person lives in a working state if current mortality and working condition prevails. Similarly, LWLE gives number of expected years by a person living under both literate and working state. The situation of females cannot be figured out without comparing both the sexes. In the present paper an attempt has been made to estimate LLE and WLE in India along with some selected states from various zones of India namely Assam from the North-East, Gujarat from the West, Kerala from the South, Rajasthan from the North, Uttar Pradesh from the Central and West Bengal from the East respectively for both the sexes based on 2011 census. Furthermore, we have also developed a formula for a new indicator namely Literate-Working Life Expectancy (LWLE) and the proposed index has been applied in India and the selected states mentioned above for both males and females. Data has been extracted from SRS(Sample Registration System) based Abridged Life Table and Census of India. The computation of LLE follows the method developed by Lutz while WLE has followed the method developed by Saw Swee Hock. By combining both the factors literacy and employment, the new indicator LWLE also follows the method like LLE and WLE. Contrasted results have been found in different parts of India. The result shows that LLE at birth is highest(lowest) in the state Kerala(Uttar Pradesh) with 61.66 (39.51) years among the males. A similar situation is also observed among the females with 62.58 years and 25.11 years respectively. But male WLE at birth is highest (lowest) in Rajasthan(Kerala) with 37.11 (32.64) years. Highest female WLE at birth is also observed in Rajasthan with 23.51 years and the lowest is concentrated in Uttar Pradesh with 11.76 years. It is also found that Kerala’s performance is exceptionally good in terms of LWLE at birth while the lowest LWLE at birth prevails in the state Uttar Pradesh among the males. Female LWLE at birth is highest(lowest) in Kerala(Uttar Pradesh) with 19.73(4.77)years. The corresponding value of the index increases as the number of factors involved in the life expectancy decrease. It is found that women are lagging behind in terms of both literacy and employment. Findings of the study will help the planners to take necessary steps to improve the position of women.

Keywords: life expectancy, literacy, literate life expectancy, working life expectancy

Procedia PDF Downloads 420

Authors: Jayashree And Gajjam

Abstract:

Intellectual humility (IH) is defined as a virtuous mean between intellectual arrogance and intellectual self-diffidence by the ‘Doxastic Account of IH’ studied, researched and developed by western scholars not earlier than 2015 at the University of Edinburgh. Ancient Indian philosophical texts or the Upanisads written in the Sanskrit language during the later Vedic period (circa 600-300 BCE) have long addressed the virtue of being humble in several stories and narratives. The current research paper questions and revisits these character traits in an Indian context following an experimental method. Based on the subjective reports of more than 400 Indian teenagers and adults, it argues that while a few traits of IH (such as trustworthiness, respectfulness, intelligence, politeness, etc.) are panhuman and pancultural, a few are not. Some attributes of IH (such as proper pride, open-mindedness, awareness of own strength, etc.) may be taken for arrogance by the Indian population, while other qualities of Intellectual Diffidence such as agreeableness, surrendering can be regarded as the characteristic of IH. The paper then gives the reasoning for this discrepancy that can be traced back to the ancient Indian (Upaniṣadic) teachings that are still prevalent in many Indian families and still anchor their views on IH. The name Upanisad itself means ‘sitting down near’ (to the Guru to gain the Supreme knowledge of the Self and the Universe and setting to rest ignorance) which is equivalent to the three traits among the BIG SEVEN characterized as IH by the western scholars viz. ‘being a good listener’, ‘curious to learn’, and ‘respect to other’s opinion’. The story of Satyakama Jabala (Chandogya Upanisad 4.4-8) who seeks the truth for several years even from the bull, the fire, the swan and waterfowl, suggests nothing but the ‘need for cognition’ or ‘desire for knowledge’. Nachiketa (Katha Upanisad), a boy with a pure mind and heart, follows his father’s words and offers himself to Yama (the God of Death) where after waiting for Yama for three days and nights, he seeks the knowledge of the mysteries of life and death. Although the main aim of these Upaniṣadic stories is to give the knowledge of life and death, the Supreme reality which can be identical with traits such as ‘curious to learn’, one cannot deny that they have a lot more to offer than mere information about true knowledge e.g., ‘politeness’, ‘good listener’, ‘awareness of own limitations’, etc. The possible future scope of this research includes (1) finding other socio-cultural factors that affect the ideas on IH such as age, gender, caste, type of education, highest qualification, place of residence and source of income, etc. which may be predominant in current Indian society despite our great teachings of the Upaniṣads, and (2) to devise different measures to impart IH in Indian children, teenagers, and younger adults for the harmonious future. The current experimental research can be considered as the first step towards these goals.

Keywords: ethics and virtue epistemology, Indian philosophy, intellectual humility, upaniṣadic texts in ancient India

Procedia PDF Downloads 91

Authors: Boguslaw Schreyer

Abstract:

During the wheeled robot’s braking process, the extra dynamic vertical forces act on all wheels: left, right, front or rear. Those forces are directed downward on the front wheels while directed upward on the rear wheels. In order to maximize the deceleration, therefore, minimize the braking time and braking distance, we need to calculate a correct torque distribution: the front braking torque should be increased, and rear torque should be decreased. At the same time, we need to provide better transversal stability. In a simple case of all adhesion coefficients being the same under all wheels, the torque distribution may secure the optimal (maximal) control of the robot braking process, securing the minimum braking distance and a minimum braking time. At the same time, the transversal stability is relatively good. At any time, we control the transversal acceleration. In the case of the transversal movement, we stop the braking process and re-apply braking torque after a defined period of time. If we correctly calculate the value of the torques, we may secure the traction coefficient under the front and rear wheels close to its maximum. Also, in order to provide an optimum braking control, we need to calculate the timing of the braking torque application and the timing of its release. The braking torques should be released shortly after the wheels passed a maximum traction coefficient (while a wheels’ slip increases) and applied again after the wheels pass a maximum of traction coefficient (while the slip decreases). The correct braking torque distribution secures the front and rear wheels, passing this maximum at the same time. It guarantees an optimum deceleration control, therefore, minimum braking time. In order to calculate a correct torque distribution, a control unit should receive the input signals of a rear torque value (which changes independently), the robot’s deceleration, and values of the vertical front and rear forces. In order to calculate the timing of torque application and torque release, more signals are needed: speed of the robot: angular speed, and angular deceleration of the wheels. In case of different adhesion coefficients under the left and right wheels, but the same under each pair of wheels- the same under right wheels and the same under left wheels, the Select-Low (SL) and select high (SH) methods are applied. The SL method is suggested if transversal stability is more important than braking efficiency. Often in the case of the robot, more important is braking efficiency; therefore, the SH method is applied with some control of the transversal stability. In the case that all adhesion coefficients are different under all wheels, the front-rear torque distribution is maintained as in all previous cases. However, the timing of the braking torque application and release is controlled by the rear wheels’ lowest adhesion coefficient. The Lagrange equations have been used to describe robot dynamics. Matlab has been used in order to simulate the process of wheeled robot braking, and in conclusion, the braking methods have been selected.

Keywords: wheeled robots, braking, traction coefficient, asymmetric

Procedia PDF Downloads 164

Authors: Tunde Ope-Davies

Abstract:

Transmediality and platformization as online content-sharing protocols have continued to accentuate the growing impact of the unprecedented digital revolution across the world. The rapid transformation across all sectors as a result of this revolution has continued to spotlight the increasing importance of new media technologies in redefining and reshaping the rhythm and dynamics of our private and public discursive practices. Equally, social and political activities are being impacted daily through the creation and transmission of political discourse content through multi-channel platforms such as mobile telephone communication, social media networks and the internet. It has been observed that digital platforms have become central to the production, processing, and distribution of multimodal social data and cultural content. The platformization paradigm thus underpins our understanding of how digital platforms enhance the production and heterogenous distribution of media and cultural content through these platforms and how this process facilitates socioeconomic and political activities. The use of multiple digital platforms to share and transmit political discourse material synchronously and asynchronously has gained some exciting momentum in the last few years. Nigeria’s 2023 general elections amplified the usage of social media and other online platforms as tools for electioneering campaigns, socio-political mobilizations and civic engagement. The study, therefore, focuses on transmedia and platformed political discourse as a new strategy to promote political candidates and their manifesto in order to mobilize support and woo voters. This innovative transmedia digital discourse model involves a constellation of online texts and images transmitted through different online platforms almost simultaneously. The data for the study was extracted from the 2023 general elections campaigns in Nigeria between January- March 2023 through media monitoring, manual download and the use of software to harvest the online electioneering campaign material. I adopted a discursive-analytic qualitative technique with toolkits drawn from a computer-mediated multimodal discourse paradigm. The study maps the progressive development of digital political discourse in this young democracy. The findings also demonstrate the inevitable transformation of modern democratic practice through platform-dependent and transmedia political discourse. Political actors and media practitioners now deploy layers of social media network platforms to convey messages and mobilize supporters in order to aggregate and maximize the impact of their media campaign projects and audience reach.

Keywords: social media, digital humanities, political discourse, platformized discourse, multimodal discourse

Procedia PDF Downloads 83

Authors: Gamaliel Salazar, Adriana Chazaro, Oscar Madrigal

Abstract:

The evolution of Unmanned Aerial Systems (UAS) has made it possible to develop new vehicles capable to perform microgravity experiments which due its cost and complexity were beyond the reach for many institutions. In this study, the aerodynamic behavior of an UAS is studied through its deceleration stage after an initial free fall phase (where the microgravity effect is generated) using Computational Fluid Dynamics (CFD). Due to the fact that the payload would be analyzed under a microgravity environment and the nature of the payload itself, the speed of the UAS must be reduced in a smoothly way. Moreover, the terminal speed of the vehicle should be low enough to preserve the integrity of the payload and vehicle during the landing stage. The UAS model is made by a study pod, control surfaces with fixed and mobile sections, landing gear and two semicircular wing sections. The speed of the vehicle is decreased by increasing the angle of attack (AoA) of each wing section from 2° (where the airfoil S1091 has its greatest aerodynamic efficiency) to 80°, creating a circular wing geometry. Drag coefficients (Cd) and forces (Fd) are obtained employing CFD analysis. A simplified 3D model of the vehicle is analyzed using Ansys Workbench 16. The distance between the object of study and the walls of the control volume is eight times the length of the vehicle. The domain is discretized using an unstructured mesh based on tetrahedral elements. The refinement of the mesh is made by defining an element size of 0.004 m in the wing and control surfaces in order to figure out the fluid behavior in the most important zones, as well as accurate approximations of the Cd. The turbulent model k-epsilon is selected to solve the governing equations of the fluids while a couple of monitors are placed in both wing and all-body vehicle to visualize the variation of the coefficients along the simulation process. Employing a statistical approximation response surface methodology the case of study is parametrized considering the AoA of the wing as the input parameter and Cd and Fd as output parameters. Based on a Central Composite Design (CCD), the Design Points (DP) are generated so the Cd and Fd for each DP could be estimated. Applying a 2nd degree polynomial approximation the drag coefficients for every AoA were determined. Using this values, the terminal speed at each position is calculated considering a specific Cd. Additionally, the distance required to reach the terminal velocity at each AoA is calculated, so the minimum distance for the entire deceleration stage without comprising the payload could be determine. The Cd max of the vehicle is 1.18, so its maximum drag will be almost like the drag generated by a parachute. This guarantees that aerodynamically the vehicle can be braked, so it could be utilized for several missions allowing repeatability of microgravity experiments.

Keywords: microgravity effect, response surface, terminal speed, unmanned system

Procedia PDF Downloads 171

Authors: Wafeek Mohamed Ibrahim Mohamed

Abstract:

In the era of globalization, the camera of the cinematographic film plays a very important role in terms of monitoring and documenting what it was and distinguished the built environment of architectural and Urbanism. Moving the audience to the out-going backward through the cinematographic film and its stereophonic screen by which the picture appears at its best and its coexistence reached now its third dimension. The camera has indicated to the city shape with its paths, (alley) lanes, buildings and its architectural style. We have seen the architectural styles in its cinematic scenes which remained a remembrance in its history, in spite of the fact that some of which has been disappearing as what happened to ‘Boulak Bridge’ in Cairo built by ‘Eiffel’ and it has been demolished, but it remains a remembrance we can see it in the films of ’Usta Hassan’and A Crime in the Quiet Neighborhood. The purpose of the fundamental research is an attempt to reach a critical view of the idea of criticism and theorizing for Architecture and Urbanism in the cinematographic film and their relationship and reflection on the ‘audience’ understanding of the public opinion related to our built environment of Architectural and Urbanism with its problems and hardness. It is like as a trial to study the Architecture and Urbanism of the built environment in the cinematographic film and hooking up (linking) a realistic view of the governing conceptual significance thereof. The aesthetic thought of our traditional environment, in a psychological and anthropological framework, derives from the cinematic concept of the Architecture and Urbanism of the place and the dynamics of the space. The architectural space considers the foundation stone of the cinematic story and the main background of the events therein, which integrate the audience into a romantic trip to the city through its symbolized image of the spaces, lanes [alley], etc. This will be done through two main branches: firstly, Reviewing during time pursuit of the Architecture and Urbanism in the cinematographic films the thirties ago in the Egyptian cinema [onset from the film ‘Bab El Hadid’ to the American University at a film of ‘Saidi at the American University’]. The research concludes the importance of the need to study the cinematic films which deal with our societies, their architectural and Urbanism concerns whether the traditional ones or the contemporary and their crisis (such as the housing crisis in the film of ‘Krakoun in the street’, etc) to study the built environment with its architectural dynamic spaces through a modernist view. In addition, using the cinema as an important Media for spreading the ideas, documenting and monitoring the current changes in the built environment through its various dramas and comedies, etc. The cinema is considered as a mirror of the society and its built environment over the epochs. It assured the unique case constituted by cinema with the audience (public opinion) through a sense of emptiness and forming the mental image related to the city and the built environment.

Keywords: architectural and urbanism, cinematographic architectural, film, space in the film, media

Procedia PDF Downloads 237

Authors: Wedad Albalawi

Abstract:

The mathematical inequalities have been the core of mathematical study and used in almost all branches of mathematics as well in various areas of science and engineering. The inequalities by Hardy, Littlewood and Polya were the first significant composition of several science. This work presents fundamental ideas, results and techniques, and it has had much influence on research in various branches of analysis. Since 1934, various inequalities have been produced and studied in the literature. Furthermore, some inequalities have been formulated by some operators; in 1989, weighted Hardy inequalities have been obtained for integration operators. Then, they obtained weighted estimates for Steklov operators that were used in the solution of the Cauchy problem for the wave equation. They were improved upon in 2011 to include the boundedness of integral operators from the weighted Sobolev space to the weighted Lebesgue space. Some inequalities have been demonstrated and improved using the Hardy–Steklov operator. Recently, a lot of integral inequalities have been improved by differential operators. Hardy inequality has been one of the tools that is used to consider integrity solutions of differential equations. Then, dynamic inequalities of Hardy and Coposon have been extended and improved by various integral operators. These inequalities would be interesting to apply in different fields of mathematics (functional spaces, partial differential equations, mathematical modeling). Some inequalities have been appeared involving Copson and Hardy inequalities on time scales to obtain new special version of them. A time scale is an arbitrary nonempty closed subset of the real numbers. Then, the dynamic inequalities on time scales have received a lot of attention in the literature and has become a major field in pure and applied mathematics. There are many applications of dynamic equations on time scales to quantum mechanics, electrical engineering, neural networks, heat transfer, combinatorics, and population dynamics. This study focuses on Hardy and Coposon inequalities, using Steklov operator on time scale in double integrals to obtain special cases of time-scale inequalities of Hardy and Copson on high dimensions. The advantage of this study is that it uses the one-dimensional classical Hardy inequality to obtain higher dimensional on time scale versions that will be applied in the solution of the Cauchy problem for the wave equation. In addition, the obtained inequalities have various applications involving discontinuous domains such as bug populations, phytoremediation of metals, wound healing, maximization problems. The proof can be done by introducing restriction on the operator in several cases. The concepts in time scale version such as time scales calculus will be used that allows to unify and extend many problems from the theories of differential and of difference equations. In addition, using chain rule, and some properties of multiple integrals on time scales, some theorems of Fubini and the inequality of H¨older.

Keywords: time scales, inequality of hardy, inequality of coposon, steklov operator

Procedia PDF Downloads 95

Authors: Anna Mirczak

Abstract:

Introduction: In connection with the aging of the population and the increase in the number of people with chronic illnesses, the priority objective for public health has become not only lengthening life, but also improving quality of life in older persons, as well as maintenance of their relative independence and active participation in social life. The most important determinant of a person’s quality of life is health. According to the literature, older people with chronic illness who live in rural settings are at greater risk for poor outcomes than their urban counterparts. Furthermore research characterizes the rural elderly as having a higher incidence of sickness, dysfunction, disability, restricted mobility, and acute and chronic conditions than their urban citizens. It is dictated by the overlapping certain specific socio-economic factors typical for rural areas which include: social and geography exclusion, limited access to health care centers, and low socioeconomic status. Aim of the study: The objective of this study was to recognize health status and needs of older people living in selected rural areas in Poland and evaluate the impacts of working in the farm on their health status. Material and methods: The study was performed personally, using interviews based on the structural questionnaires, during the period from March 2011 to October 2012. The group of respondents consisted 203 people aged 65 years and over living in selected rural areas in Poland. The analysis of collected research material was performed using the statistical package SPSS 19 for Windows. The level of significance for the tested the hypotheses assumed value of 0.05. Results: The mean age of participants was 75,5 years (SD=5,7) range from 65 to 94 years. Most of the interviewees had children (89.2%) and grandchildren (83.7) and lived mainly with family members (75.9%) mostly in double (46.8%) and triple (20.8%) household. The majority of respondents (71,9%) were physical working on the farm. At the time of interview, each of the respondents reported that they had been diagnosed with at least one chronic diseases by their GP. The most common were: hypertension (67,5%), osteoarthritis (44,8%), atherosclerosis (43,3%), cataract (40,4%), arrhythmia (28,6%), diabetes mellitus (19,7%) and stomach or duodenum ulcer diseases (17,2%).The number of diseases occurring of the sample was dependent on gender and age. Significant associations were observed between working on the farm and frequency of occurrence cardiovascular diseases, the gastrointestinal tract dysfunction and sensory disorders. Conclusions: The most common causes of disability among older citizens were: chronic diseases, malnutrition and complaints about access to health services (especially to cardiologist and an ophthalmologist). Health care access and health status are a particular concern in rural areas where the population is older, has lower education and income levels, and is more likely to be living in medically underserved areas than is the case in urban areas.

Keywords: ageing, health status, older people, rural

Procedia PDF Downloads 262

Authors: Charles Davidson

Abstract:

This paper presents the Stoplight Analysis System of Partnering Organizations Readiness, offering a structured framework to evaluate conflict resolution collaboration feasibility, especially crucial in conflict areas, employing a colour-coded approach and specific assessment points, with implications for more informed decision-making and improved outcomes in peacebuilding initiatives. Derived from at total of 40 years of practical peacebuilding experience from the project’s two researchers as well as interviews of various other peacebuilding actors, this paper introduces the Stoplight Analysis System of Partnering Organizations Readiness, a comprehensive framework designed to facilitate effective collaboration in international/local peacebuilding partnerships by evaluating the readiness of both potential partner organisations and the location of the proposed project. ^The system employs a colour-coded approach, categorising potential partnerships into three distinct indicators: Red (no-go), Yellow (requires further research), and Green (promising, go ahead). Within each category, specific points are identified for assessment, guiding decision-makers in evaluating the feasibility and potential success of collaboration. The Red category signals significant barriers, prompting an immediate stoppage in the consideration of partnership. The Yellow category encourages deeper investigation to determine whether potential issues can be mitigated, while the Green category signifies organisations deemed ready for collaboration. This systematic and structured approach empowers decision-makers to make informed choices, enhancing the likelihood of successful and mutually beneficial partnerships. Methodologically, this paper utilised interviews from peacebuilders from around the globe, scholarly research of extant strategies, and a collaborative review of programming from the project’s two authors from their own time in the field. This method as a formalised model has been employed for the past two years across a litany of partnership considerations, and has been adjusted according to its field experimentation. This research holds significant importance in the field of conflict resolution as it provides a systematic and structured approach to peacebuilding partnership evaluation. In conflict-affected regions, where the dynamics are complex and challenging, the Stoplight Analysis System offers decision-makers a practical tool to assess the readiness of partnering organisations. This approach can enhance the efficiency of conflict resolution efforts by ensuring that resources are directed towards partnerships with a higher likelihood of success, ultimately contributing to more effective and sustainable peacebuilding outcomes.

Keywords: collaboration, conflict resolution, partnerships, peacebuilding

Procedia PDF Downloads 63

Authors: Debabrata Adhikari, Mikhail Matveev, Louise Brown, Andy Long, Jan Kočí

Abstract:

A good understanding of mesoscale permeability of complex architectures in fibrous porous preforms is of particular interest in order to achieve efficient and cost-effective resin impregnation of liquid composite molding (LCM). Fabrics used in structural reinforcements are typically woven or stitched. However, 3D fabric reinforcement is of particular interest because of the versatility in the weaving pattern with the binder yarn and in-plain yarn arrangements to manufacture thick composite parts, overcome the limitation in delamination, improve toughness etc. To predict the permeability based on the available pore spaces between the inter yarn spaces, unit cell-based computational fluid dynamics models have been using the Stokes Darcy model. Typically, the preform consists of an arrangement of yarns with spacing in the order of mm, wherein each yarn consists of thousands of filaments with spacing in the order of μm. The fluid flow during infusion exchanges the mass between the intra and inter yarn channels, meaning there is no dead-end of flow between the mesopore in the inter yarn space and the micropore in the yarn. Several studies have employed the Brinkman equation to take into account the flow through dual-scale porosity reinforcement to estimate their permeability. Furthermore, to reduce the computational effort of dual scale flow, scale separation criteria based on the ratio between yarn permeability to the yarn spacing was also proposed to quantify the dual scale and negligible micro-scale flow regime for the prediction of mesoscale permeability. In the present work, the key parameter to identify the influence of intra yarn permeability on the mesoscale permeability has been investigated with the systematic study of weft and warp yarn spacing on the plane weave as well as the position of binder yarn and number of in-plane yarn layers on 3D weave fabric. The permeability tensor has been estimated using an OpenFOAM-based model for the various weave pattern with idealized geometry of yarn implemented using open-source software TexGen. Additionally, scale separation criterion has been established based on the various configuration of yarn permeability for the 3D fabric with both the isotropic and anisotropic yarn from Gebart’s model. It was observed that the variation of mesoscale permeability Kxx within 30% when the isotropic porous yarn is considered for a 3D fabric with binder yarn. Furthermore, the permeability model developed in this study will be used for multi-objective optimizations of the preform mesoscale geometry in terms of yarn spacing, binder pattern, and a number of layers with an aim to obtain improved permeability and reduced void content during the LCM process.

Keywords: permeability, 3D fabric, dual-scale flow, liquid composite molding

Procedia PDF Downloads 94

Authors: Tinnaphop Sinsomboonthong

Abstract:

The hashtag, #LoveWins, has been widely used for celebrating the victory of the LGBTQ movement since June 2015 when the US Supreme Court enacted the rights of same-sex marriage. Nowadays, the hashtag is generally used among active social media users in many countries, including Thailand. Amidst the political conflict between advocates of the junta-backed legislation related to same-sex marriage laws, known as ‘Thailand’s Civil Partnership Draft Bills,’ and its detractors, the hashtag becomes crucial for Thailand’s 2019 national election season and shortly afterward as it was one of the most crucial parts of a political campaign to rebrand many political parties’ image, create an LGBT-friendly atmosphere and neutralize the bi-polarized politics of the law. The use of the hashtag is, therefore, not just an online entertainment but a politico-discursive tool, used by many actors for many purposes. Behind the confrontation between supporters and opposers of the law, the hashtag is used by both sides to highlight the Western-centric normativity of homosexual love, closely associated with Eurocentric modernity and heteronormativity. As an online ethnographical study, this paper aims to analyze how #LoveWins is used among Thai social media users in late 2018 to mid-2019 and how it is signified by Thai social media users during the Drafted-Bills period and the 2019 national election. A number of preliminary surveys of data on Twitter were conducted in December 2018 and, more intensely, in January 2019. Later, the data survey was officially conducted twice during February and April 2019, while the data collection was done during May-June 2019. Only public posts on Twitter that include the hashtag, #LoveWins, or any hashtags quoting ‘love’ and ‘wins’ are the main targets of this research. As a result of this, the use of the hashtag can be categorized into three levels, including banal decoration, homosexual love celebration, and colonial discourse on homosexual love. Particularly in the third type of the use of the hashtag, discourse analysis is applied to reveal that this hashtag is closely associated with the discourse of development and modernity as most of the descriptive posts demonstrate aspirations to become more ‘developed and modernized’ like many Western countries and Taiwan, the LGBT capital in Asia. Thus, calls for the ‘right to homosexual love’ and the ‘right to same-sex marriage’ in Thailand are shaped and formulated within the discursive linkage between modernity, development, and love. Also, the use of #LoveWins can be considered as a de-queering process of love as only particular types of gender identity, sexual orientation, and relationships that reflect Eurocentric modernity and heteronormativity are acceptable and advocated. Due to this, more inclusive queer loves should be supported rather than a mere essentialist-traditionalist homosexual love. Homonormativity must be deconstructed, and love must no longer be reserved for only one particular type of relationship that is standardized from/by the West. It must become more inclusive.

Keywords: #LoveWins, homosexual love, LGBT rights, same-sex marriage

Procedia PDF Downloads 138

Authors: K. Nazan Turhan, Tuğçe Ersan

Abstract:

The population of the world is approximately 8 billion, and it increases uncontrollably and irrepressibly, leading to an increase in consumption. This situation causes crucial problems, and food waste is one of these. The Food and Agriculture Organization of the United Nations (FAO) defines food waste as the discarding or alternative utilization of food that is safe and nutritious for the consumption of humans along the entire food supply chain, from primary production to end household consumer level. In addition, according to the estimation of FAO, one-third of all food produced for human consumption is lost or wasted worldwide every year. Wasting food endangers natural resources and causes hunger. For instance, excessive amounts of food waste cause greenhouse gas emissions, contributing to global warming. Therefore, waste management has been gaining significance in the last few decades at both local and global levels due to the expected scarcity of resources for the increasing population of the world. There are several ways to recover food waste. According to the United States Environmental Protection Agency’s Food Recovery Hierarchy, food waste recovery ways are source reduction, feeding hungry people, feeding animals, industrial uses, composting, and landfill/incineration from the most preferred to the least preferred, respectively. Bioethanol, biodiesel, biogas, agricultural fertilizer and animal feed can be obtained from food waste that is generated by different food industries. In this project, feeding animals was selected as a food waste recovery method and food waste of a plant was used to provide ingredient uniformity. Grasshoppers were used as a protein source. In other words, the project was performed to develop a dog food product by recovery of the plant’s food waste after following some steps. The collected food waste and purchased grasshoppers were sterilized, dried and pulverized. Then, they were all mixed with 60 g agar-agar solution (4%w/v). 3 different aromas were added, separately to the samples to enhance flavour quality. Since there are differences in the required amounts of different species of dogs, fulfilling all nutritional needs is one of the problems. In other words, there is a wide range of nutritional needs in terms of carbohydrates, protein, fat, sodium, calcium, and so on. Furthermore, the requirements differ depending on age, gender, weight, height, and species. Therefore, the product that was developed contains average amounts of each substance so as not to cause any deficiency or surplus. On the other hand, it contains more protein than similar products in the market. The product was evaluated in terms of contamination and nutritional content. For contamination risk, detection of E. coli and Salmonella experiments were performed, and the results were negative. For the nutritional value test, protein content analysis was done. The protein contents of different samples vary between 33.68% and 26.07%. In addition, water activity analysis was performed, and the water activity (aw) values of different samples ranged between 0.2456 and 0.4145.

Keywords: food waste, dog food, animal nutrition, food waste recovery

Procedia PDF Downloads 62

Authors: Emily Cherono Sawe, Elisha Ondieki Makori

Abstract:

Knowledge and digital economies have brought challenges and potential opportunities for universities to innovate and improve the quality of learning. Disruption technologies and information dynamics continue to transform and change the landscape in teaching, scholarship, and research activities across universities. Digital literacy is a fundamental and imperative element in higher education and training, as witnessed during the new norm. COVID-19 caused unprecedented disruption in universities, where teaching and learning depended on digital innovations and applications. Academic services and activities were provided online, including library information services. Information professionals were forced to adopt various digital platforms in order to provide information services to patrons. University libraries’ roles in fulfilling educational responsibilities continue to evolve in response to changes in pedagogy, technology, economy, society, policies, and strategies of parent institutions. Libraries are currently undergoing considerable transformational change as a result of the inclusion of a digital environment. Academic libraries have been at the forefront of providing online learning resources and online information services, as well as supporting students and staff to develop digital literacy skills via online courses, tutorials, and workshops. Digital literacy transformation and information staff are crucial elements reminiscent of the prioritization of skills and knowledge for lifelong learning. The purpose of this baseline research is to assess the implications of digital literacy transformation in institutions of higher learning in Kenya and share appropriate strategies to leverage and sustain teaching and research. Objectives include examining the leverage and preparedness of the digital literacy environment in streamlining learning in the universities, exploring and benchmarking imperative digital competence for information professionals, establishing the perception of information professionals towards digital literacy skills, and determining lessons, best practices, and strategies to accelerate digital literacy transformation for effective research and learning in the universities. The study will adopt a descriptive research design using questionnaires and document analysis as the instruments for data collection. The targeted population is librarians and information professionals, as well as academics in public and private universities teaching information literacy programmes. Data and information are to be collected through an online structured questionnaire and digital face-to-face interviews. Findings and results will provide promising lessons together with best practices and strategies to transform and change digital literacies in university libraries in Kenya.

Keywords: digital literacy, digital innovations, information professionals, librarians, higher education, university libraries, digital information literacy

Procedia PDF Downloads 91

Authors: Markéta Chmelíková, David Ullrich, Iva Burešová

Abstract:

The paper maps the possibilities and limits of diagnosing selected personality and performance characteristics of military leadership and psychology students in the context of coping with challenging situations. Individuals vary greatly inter-individually in their ability to effectively manage extreme situations, yet existing diagnostic tools are often criticized mainly for their low predictive power. Nowadays, every modern army focuses primarily on the systematic minimization of potential risks, including the prediction of desirable forms of behavior and the performance of military commanders. The context of military leadership is well known for its life-threatening nature. Therefore, it is crucial to research stress load in the specific context of military leadership for the purpose of possible anticipation of human failure in managing extreme situations of military leadership. The aim of the submitted pilot study, using an experiment of 24 hours duration, is to verify the possibilities of a specific combination of psychodiagnostic to predict people who possess suitable equipment for coping with increased stress load. In our pilot study, we conducted an experiment of 24 hours duration with an experimental group (N=13) in the bomb shelter and a control group (N=11) in a classroom. Both groups were represented by military leadership students (N=11) and psychology students (N=13). Both groups were equalized in terms of study type and gender. Participants were administered the following test battery of personality characteristics: Big Five Inventory 2 (BFI-2), Short Dark Triad (SD-3), Emotion Regulation Questionnaire (ERQ), Fatigue Severity Scale (FSS), and Impulsive Behavior Scale (UPPS-P). This test battery was administered only once at the beginning of the experiment. Along with this, they were administered a test battery consisting of the Test of Attention (d2) and the Bourdon test four times overall with 6 hours ranges. To better simulate an extreme situation – we tried to induce sleep deprivation - participants were required to try not to fall asleep throughout the experiment. Despite the assumption that a stay in an underground bomb shelter will manifest in impaired cognitive performance, this expectation has been significantly confirmed in only one measurement, which can be interpreted as marginal in the context of multiple testing. This finding is a fundamental insight into the issue of stress management in extreme situations, which is crucial for effective military leadership. The results suggest that a 24-hour stay in a shelter, together with sleep deprivation, does not seem to simulate sufficient stress for an individual, which would be reflected in the level of cognitive performance. In the context of these findings, it would be interesting in future to extend the diagnostic battery with physiological indicators of stress, such as: heart rate, stress score, physical stress, mental stress ect.

Keywords: bomb shelter, extreme situation, military leadership, psychodiagnostic

Procedia PDF Downloads 90

Authors: Naveed Ali

Abstract:

Under the construct of the ‘traditional family’ set-up (male and female parent) in the United Kingdom, the absence of a male parental figure remains a critical factor associated with an elevated risk of criminal behavior among youths. Empirical evidence suggests that father absence significantly correlates with increased rates of juvenile delinquency and criminality. For instance, data reveals that approximately 63% of young offenders in the United Kingdom originate from single-parent households, predominantly those without a father. Moreover, research displays that boys from father-absent homes are three times more likely to exhibit antisocial behavior compared to their peers from two-parent families. This absence can negatively impact educational attainment, with children from fatherless homes being twice as likely to leave school prematurely, thereby increasing their vulnerability to peer influence and gang affiliation- key pathways into criminal activities. Both legal frameworks and social policies in the United Kingdom acknowledge the pivotal role of family stability in crime prevention. Initiatives including parenting support programs, community-based interventions, and targeted youth services seek to address the challenges faced by single-parent families and mitigate the criminogenic effects of father absence. Despite these efforts, persistent challenges remain, including the need to address the broader socioeconomic determinants of family instability and to refine legal strategies that effectively address the root causes of youth offending linked to the absence of a male parental figure. A nuanced understanding of these dynamics is essential for developing more effective legal and social interventions aimed at reducing juvenile delinquency and supporting at-risk populations within the United Kingdom. This paper will highlight the significant impact of the absence of a male parental figure on youth crime rates in the United Kingdom, underlining the need for enhanced legal and social responses. By examining the interplay between family structure and juvenile offending, the paper will underline the importance of developing more comprehensive interventions that address both familial factors and the wider socioeconomic context. The findings aim to guide policymakers and practitioners in creating more effective strategies to reduce youth crime, ultimately strengthening support systems for vulnerable families and mitigating the adverse effects of father absence on young individuals.

Keywords: criminality, family law, legal framework, the united kingdom perspective

Procedia PDF Downloads 27

Authors: Benjamin O. Ehigie, Aderemi Alarape, Nyitor Shenge, Sylvester A. Okhakhume, Timileyin Fashola, Fiyinfunjah Dosumu

Abstract:

Organisational citizenship behaviour (OCB) is a construct in industrial and organisational behaviour that explains a person's voluntary commitment within an organisation, which is outside the scope of his or her contractual tasks. To attain organisational effectiveness the human factor of production is inevitable, hence the importance of employee behaviour. While the concept of organisational citizenship behavior is mostly discussed in the context of the workplace, it is reasoned that the idea could be reflective in relation to national commitment. Many developing countries in Africa, including Nigeria, suffer economic hardship today not necessarily due to poor resources but bad management of the resources. The mangers of their economies are not committed to the tenets of economic growth but engrossed in fraud, corruption, bribery, and other economic vices. It is this backdrop that necessitated the development and validation of the Ibadan-Nigeria Citizenship Behaviour (I-NCB) Scale. The study adopted a cross-sectional survey (online) research design, using 2404 postgraduate students in the Premier University of the country, with 99.2% being Nigerians and 0.8% non-Nigerians. Gender composition was 1,439 (60%) males and 965 (40%) females, 1201 (50%) were employed while 1203 50% unemployed, 74.2% of the employed were in public paid employment, 19.5% in private sector, and 6.3% were self-employed. Through literature review, 78 items were generated. Using 10 lecturers and 21 students, content and face validity were established respectively. Data collected were subjected to reliability and factor analytic statistics at p < .05 level of significance. Results of the content and face validity at 80% level of item acceptance resulted to 60 items; this was further reduced to 50 after item-total correlation using r=.30 criterion. Divergent validity of r= -.28 and convergent validity of r= .44 were obtained by correlating the I-NCB scale with standardized Counterproductive work behaviour (CWB) scale and Organisational Citizenship Behaviour (OCB) scale among the workers. The reliability coefficients obtained were; Cronbach alpha of internal consistency (α = 0.941) and split-half reliability of r = 0.728. Factor analyses of the I-NCB scale with principal component and varimax rotation yielded five factors when Eigenvalue above 1 were extracted. The factors which accounted for larger proportions of the total variance were given factor names as; Altruistic, Attachment, Affective, Civic responsibility and Allegiance. As much as there are vast journals on citizenship behaviour in organisations, there exists no standardized tool to measure citizenship behaviour of a country. The Ibadan-Nigeria Citizenship Behaviour (I-NCB) scale was consequently developed. The scale could be used to select personnel into political positions and senior administrative positions among career workers in Nigeria, with the aim of determining national commitment to service.

Keywords: counterproductive work behaviour, CWB, Nigeria Citizenship Behaviour, organisational citizenship behaviour, OCB, Ibadan

Procedia PDF Downloads 249

Authors: Buket Celik Ünal, Onur Ünal

Abstract:

Communication is the most challenging part of maintenance operations. Communication between expert and fieldworker is crucial for effective maintenance and this also affects the safety of the fieldworkers. To support a machine user in a remote collaborative physical task, both, a mobile and a stationary device are needed. Such a system is called a shared vision system and the system supports two people to solve a problem from different places. This system reduces the errors and provides a reliable support for qualified and less qualified users. Through this research, it was aimed to validate the effectiveness of using a shared vision system to facilitate communication between on-site workers and those issuing instructions regarding maintenance or inspection works over long distances. The system is designed with head-worn display which is called a shared vision system. As a part of this study, a substitute system is used and implemented by using a shared vision system for maintenance operation. The benefits of the use of a shared vision system are analyzed and results are adapted to the wind turbines to improve the occupational safety and health for maintenance technicians. The motivation for the research effort in this study can be summarized in the following research questions: -How can expert support technician over long distances during maintenance operation? -What are the advantages of using a shared vision system? Experience from the experiment shows that using a shared vision system is an advantage for both electrical and mechanical system failures. Results support that the shared vision system can be used for wind turbine maintenance and repair tasks. Because wind turbine generator/gearbox and the substitute system have similar failures. Electrical failures, such as voltage irregularities, wiring failures and mechanical failures, such as alignment, vibration, over-speed conditions are the common and similar failures for both. Furthermore, it was analyzed the effectiveness of the shared vision system by using a smart glasses in connection with the maintenance task performed by a substitute system under four different circumstances, namely by using a shared vision system, an audio communication, a smartphone and by yourself condition. A suitable method for determining dependencies between factors measured in Chi Square Test, and Chi Square Test for Independence measured for determining a relationship between two qualitative variables and finally Mann Whitney U Test is used to compare any two data sets. While based on this experiment, no relation was found between the results and the gender. Participants` responses confirmed that the shared vision system is efficient and helpful for maintenance operations. From the results of the research, there was a statistically significant difference in the average time taken by subjects on works using a shared vision system under the other conditions. Additionally, this study confirmed that a shared vision system provides reduction in time to diagnose and resolve maintenance issues, reduction in diagnosis errors, reduced travel costs for experts, and increased reliability in service.

Keywords: communication support, maintenance and inspection tasks, occupational health and safety, shared vision system

Procedia PDF Downloads 259

Authors: Aisha Ijaz

Abstract:

The paper focuses on the impact of Muslim religiosity on convenience food purchases and involvement experienced in a non-Muslim culture. There is a scarcity of research on the purchasing patterns of Muslim diaspora communities residing in risk societies, particularly in contexts where there is an increasing inclination toward industrialized food items alongside a renewed interest in the concept of natural foods. The United Kingdom serves as an appropriate setting for this study due to the increasing Muslim population in the country, paralleled by the expanding Halal Food Market. A multi-dimensional framework is proposed, testing for five forms of involvement, specifically Purchase Decision Involvement, Product Involvement, Behavioural Involvement, Intrinsic Risk and Extrinsic Risk. Quantitative cross-sectional consumer data were collected through a face-to-face survey contact method with 141 Muslims during the summer of 2020 in Liverpool located in the Northwest of England. proportion formula was utilitsed, and the population of interest was stratified by gender and age before recruitment took place through local mosques and community centers. Six input variables were used (intrinsic religiosity and involvement dimensions), dividing the sample into 4 clusters using the Two-Step Cluster Analysis procedure in SPSS. Nuanced variances were observed in the type of involvement experienced by religiosity group, which influences behaviour when purchasing convenience food. Four distinct market segments were identified: highly religious ego-involving (39.7%), less religious active (26.2%), highly religious unaware (16.3%), less religious concerned (17.7%). These segments differ significantly with respects to their involvement, behavioural variables (place of purchase and information sources used), socio-cultural (acculturation and social class), and individual characteristics. Choosing the appropriate convenience food is centrally related to the value system of highly religious ego-involving first-generation Muslims, which explains their preference for shopping at ethnic food stores. Less religious active consumers are older and highly alert in information processing to make the optimal food choice, relying heavily on product label sources. Highly religious unaware Muslims are less dietary acculturated to the UK diet and tend to rely on digital and expert advice sources. The less-religious concerned segment, who are typified by younger age and third generation, are engaged with the purchase process because they are worried about making unsuitable food choices. Research implications are outlined and potential avenues for further explorations are identified.

Keywords: consumer behaviour, consumption, convenience food, religion, muslims, UK

Procedia PDF Downloads 55

Authors: Kassahun Tilahun

Abstract:

The purpose of the study was two-fold: to examine the socio-demographic and psychological predictors of well-being and formulate a socio-culturally sound approach explaining the meaning and experience of psychological well-being among Ethiopian adults. Ryan and Deci’s Self-Determination Theory was duly considered as a theoretical framework of the study. The study followed a sequential explanatory mixed method design. Both quantitative and qualitative data were obtained, via scales and open-ended questionnaires, from 438 civil servants working in Addis Ababa. 30 interviews were also conducted to gain further information. An in-depth analysis of the reliability and validity of instruments was made before employing them to the main study. The results showed that adults were better off in both their scores of psychological and subjective well-being. Besides, adults’ well-being was found to be quite a function of their gender, age, marital status, educational level and household income. Males had a healthier psychological well-being status than females, where as females were better in their subjective well-being. A significant difference in psychological well-being was also observed between emerging and young adults, in favor of the young; and between cohabitated and married adults, married being advantageous. A significant difference in subjective well-being measures was also noticed among single, cohabitated and married adults, in favor of the married adults in all measures. The finding revealed that happiness level of adults decrease as their educational status increases while the reverse is true to psychological well-being. Besides, as adults’ household income boosts, so do their psychological well-being and satisfaction in life. The regression analysis also produced significant independent contributions of household income to overall well-being of adults. As such, subjective well-being was significantly predicted by dummy variable of sex and marital status. Likewise, the agreeableness, conscientiousness, neuroticism and openness dimensions of personality were notable significant predictors of adults’ psychological well-being where as extraversion and agreeableness were significant predictors of their subjective well-being. Religiosity was also a significant predictor of adults’ psychological well-being. Besides, adults’ well-being was significantly predicted by the interaction between conscientiousness and religiosity. From goal pursuit dimensions, attainment of extrinsic life goals was a significant predictor of both psychological and subjective well-being. Importance and attainment of intrinsic life goals also significantly predicts adults’ psychological well-being. Finally, the subjective well-being of adults was significantly predicted by environmental mastery, positive relations with others, self-acceptance and overall psychological well-being scores of adults. The thematic analysis identified five major categories of themes, which are essential in explaining the psychological well-being of Ethiopian adults. These were; socio-cultural harmony, social cohesion, security, competence and accomplishment, and the self. Detailed discussion on the rational for including these themes was made and appropriate implications were proposed. Researchers are encouraged to expand the findings of this research and in turn develop a suitable approach taping the psychological well-being of adults living in countries like Ethiopia.

Keywords: psychological well-being, subjective well-being, adulthood, Ethiopia

Procedia PDF Downloads 536

Authors: Ibrahim Musa, Mohammed Abdul-Aziz Mabrouk, Yusuf Tanko

Abstract:

Introduction: Long term physical training affect the performance of athletes especially the females. Soccer which is a team sport, played in an outdoor field, require adequate oxygen transport system for the maximal aerobic power during exercise in order to complete 90 minutes of competitive play. Suboptimal haematological status has often been recorded in athletes with intensive physical activity. It may be due to the iron depletion caused by hemolysis or haemodilution results from plasma volume expansion. There is lack of data regarding the dynamics of red blood cell variables, in male football players. We hypothesized that, a long competitive season involving frequent matches and intense training could influence red blood cell variables, as a consequence of applying repeated physical loads when compared with sedentary. Methods: This cross sectional study was carried on 40 adult males (20 athletes and 20 non athletes) between 18-25 years of age. The 20 apparently healthy male non athletes were taken as sedentary and 20 male footballers comprise the study group. The university institutional review board (ABUTH/HREC/TRG/36) gave approval for all procedures in accordance with the Declaration of Helsinki. Red blood cell (RBC) concentration, packed cell volume (PCV), and plasma volume were measured in fasting state and immediately after exercise. Statistical analysis was done by using SPSS/ win.20.0 for comparison within and between the groups, using student’s paired and unpaired “t” test respectively. Results: The finding from our study shows that, immediately after termination of exercise, the mean RBC counts and PCV significantly (p<0.005) decreased with significant increased (p<0.005) in plasma volume when compared with pre-exercised values in both group. In addition the post exercise RBC was significantly higher in untrained (261.10±8.5) when compared with trained (255.20±4.5). However, there was no significant differences in the post exercise hematocrit and plasma volume parameters between the sedentary and the footballers. Moreover, beside changes in pre-exercise values among the sedentary and the football players, the resting red blood cell counts and Plasma volume (PV %) was significantly (p < 0.05) higher in the sedentary group (306.30±10.05 x 104 /mm3; 58.40±0.54%) when compared with football players (293.70±4.65 x 104 /mm3; 55.60±1.18%). On the other hand, the sedentary group exhibited significant (p < 0.05) decrease in PCV (41.60±0.54%) when compared with the football players (44.40±1.18%). Conclusions: It is therefore proposed that the acute football exercise induced reduction in RBC and PCV is entirely due to plasma volume expansion, and not of red blood cell hemolysis. In addition, the training status also influenced haematological indices of male football players differently from the sedentary at rest due to adaptive response. This is novel.

Keywords: Haematological Indices, Performance Status, Sedentary, Male Football Players

Procedia PDF Downloads 254

Authors: Ioannis Panagiotopoulos, Aristidis Anastasakis, Konstantinos Toutouzas, Ioannis Iakovou, Charalampos Vlachopoulos, Vasilis Voudris, Georgios Tziomalos, Konstantinos Tsioufis, Efstathios Kastritis, Alexandros Briassoulis, Kimon Stamatelopoulos, Alexios Antonopoulos, Paraskevi Exadaktylou, Evanthia Giannoula, Anastasia Katinioti, Maria Kalantzi, Evangelos Leontiadis, Eftychia Smparouni, Ioannis Malakos, Nikolaos Aravanis, Argyrios Doumas, Maria Koutelou

Abstract:

Introduction: Cardiac amyloidosis from Transthyretin (ATTR-CA) is an infiltrative disease characterized by the deposition of pathological transthyretin complexes in the myocardium. This study describes the characteristics of patients diagnosed with ATTR-CA from 2019 until present at the Nuclear Medicine Department of Onassis Cardiac Surgery Center and AHEPA Hospital. These centers have extensive experience in amyloidosis and modern technological equipment for its diagnosis. Materials and Methods: Records of consecutive patients (N=73) diagnosed with any type of amyloidosis were collected, analyzed, and prospectively followed. The diagnosis of amyloidosis was made using specific myocardial scintigraphy with Tc-99m DPD. Demographic characteristics, including age, gender, marital status, height, and weight, were collected in a database. Clinical characteristics, such as amyloidosis type (ATTR and AL), serum biomarkers (BNP, troponin), electrocardiographic findings, ultrasound findings, NYHA class, aortic valve replacement, device implants, and medication history, were also collected. Some of the most significant results are presented. Results: A total of 73 cases (86% male) were diagnosed with amyloidosis over four years. The mean age at diagnosis was 82 years, and the main symptom was dyspnea. Most patients suffered from ATTR-CA (65 vs. 8 with AL). Out of all the ATTR-CA patients, 61 were diagnosed with wild-type and 2 with two rare mutations. Twenty-eight patients had systemic amyloidosis with extracardiac involvement, and 32 patients had a history of bilateral carpal tunnel syndrome. Four patients had already developed polyneuropathy, and the diagnosis was confirmed by DPD scintigraphy, which is known for its high sensitivity. Among patients with isolated cardiac involvement, only 6 had left ventricular ejection fraction below 40%. The majority of ATTR patients underwent tafamidis treatment immediately after diagnosis. Conclusion: In conclusion, the experiences shared by the two centers and the continuous exchange of information provide valuable insights into the diagnosis and management of cardiac amyloidosis. Clinical suspicion of amyloidosis and early diagnostic approach are crucial, given the availability of non-invasive techniques. Cardiac scintigraphy with DPD can confirm the presence of the disease without the need for a biopsy. The ultimate goal still remains continuous education and awareness of clinical cardiologists so that this systemic and treatable disease can be diagnosed and certified promptly and treatment can begin as soon as possible.

Keywords: amyloidosis, diagnosis, myocardial scintigraphy, Tc-99m DPD, transthyretin

Procedia PDF Downloads 86

Authors: Funda Erdem Şahnali, Ş. Özgür Atayılmaz, Tolga N. Aynur

Abstract:

Almost all of the domestic refrigerators operate on the principle of the vapor compression refrigeration cycle and removal of heat from the refrigerator cabinets is done via one of the two methods: natural convection or forced convection. In this study, airflow and temperature distributions inside a 375L no-frost type larder cabinet, in which cooling is provided by forced convection, are evaluated both experimentally and numerically. Airflow rate, compressor capacity and temperature distribution in the cooling chamber are known to be some of the most important factors that affect the cooling performance and energy consumption of a refrigerator. The objective of this study is to evaluate the original temperature distribution in the larder cabinet, and investigate for better temperature distribution solutions throughout the refrigerator domain via system optimizations that could provide uniform temperature distribution. The flow visualization and airflow velocity measurements inside the original refrigerator are performed via Stereoscopic Particle Image Velocimetry (SPIV). In addition, airflow and temperature distributions are investigated numerically with Ansys Fluent. In order to study the heat transfer inside the aforementioned refrigerator, forced convection theories covering the following cases are applied: closed rectangular cavity representing heat transfer inside the refrigerating compartment. The cavity volume has been represented with finite volume elements and is solved computationally with appropriate momentum and energy equations (Navier-Stokes equations). The 3D model is analyzed as transient, with k-ε turbulence model and SIMPLE pressure-velocity coupling for turbulent flow situation. The results obtained with the 3D numerical simulations are in quite good agreement with the experimental airflow measurements using the SPIV technique. After Computational Fluid Dynamics (CFD) analysis of the baseline case, the effects of three parameters: compressor capacity, fan rotational speed and type of shelf (glass or wire) are studied on the energy consumption; pull down time, temperature distributions in the cabinet. For each case, energy consumption based on experimental results is calculated. After the analysis, the main effective parameters for temperature distribution inside a cabin and energy consumption based on CFD simulation are determined and simulation results are supplied for Design of Experiments (DOE) as input data for optimization. The best configuration with minimum energy consumption that provides minimum temperature difference between the shelves inside the cabinet is determined.

Keywords: air distribution, CFD, DOE, energy consumption, experimental, larder cabinet, refrigeration, uniform temperature

Procedia PDF Downloads 108

Authors: Kalu Uka Orji, Nasiman Sapari, Khamaruzaman W. Yusof

Abstract:

Exposure of galena (PbS), tealite (PbSnS2), and other associated minerals during mining activities release lead (Pb) and other heavy metals into the mining water through oxidation and dissolution. Heavy metal pollution has become an environmental challenge. Lead, for instance, can cause toxic effects to human health, including brain damage. Ex-mining pond water was reported to contain lead as high as 69.46 mg/L. Conventional treatment does not easily remove lead from water. A promising and emerging treatment technology for lead removal is the application of the electrocoagulation (EC) process. However, some of the problems associated with EC are systematic reactor design, selection of maximum EC operating parameters, scale-up, among others. This study investigated an EC process for the removal of lead from synthetic ex-mining pond water using a batch reactor and Fe electrodes. The effects of various operating parameters on lead removal efficiency were examined. The results obtained indicated that the maximum removal efficiency of 98.6% was achieved at an initial PH of 9, the current density of 15mA/cm2, electrode spacing of 0.3cm, treatment time of 60 minutes, Liquid Motion of Magnetic Stirring (LM-MS), and electrode arrangement = BP-S. The above experimental data were further modeled and optimized using a 2-Level 4-Factor Full Factorial design, a Response Surface Methodology (RSM). The four factors optimized were the current density, electrode spacing, electrode arrangements, and Liquid Motion Driving Mode (LM). Based on the regression model and the analysis of variance (ANOVA) at 0.01%, the results showed that an increase in current density and LM-MS increased the removal efficiency while the reverse was the case for electrode spacing. The model predicted the optimal lead removal efficiency of 99.962% with an electrode spacing of 0.38 cm alongside others. Applying the predicted parameters, the lead removal efficiency of 100% was actualized. The electrode and energy consumptions were 0.192kg/m3 and 2.56 kWh/m3 respectively. Meanwhile, the adsorption kinetic studies indicated that the overall lead adsorption system belongs to the pseudo-second-order kinetic model. The adsorption dynamics were also random, spontaneous, and endothermic. The higher temperature of the process enhances adsorption capacity. Furthermore, the adsorption isotherm fitted the Freundlish model more than the Langmuir model; describing the adsorption on a heterogeneous surface and showed good adsorption efficiency by the Fe electrodes. Adsorption of Pb2+ onto the Fe electrodes was a complex reaction, involving more than one mechanism. The overall results proved that EC is an efficient technique for lead removal from synthetic mining pond water. The findings of this study would have application in the scale-up of EC reactor and in the design of water treatment plants for feed-water sources that contain lead using the electrocoagulation method.

Keywords: ex-mining water, electrocoagulation, lead, adsorption kinetics

Procedia PDF Downloads 147

Authors: Ram V. Mohan, John Rivas-Murillo, Ahmed Mohamed, Wayne D. Hodo

Abstract:

Cementitious materials, an excellent example of highly complex, heterogeneous material systems, are cement-based systems that include cement paste, mortar, and concrete that are heavily used in civil infrastructure; though commonly used are one of the most complex in terms of the material morphology and structure than most materials, for example, crystalline metals. Processes and features occurring at the nanometer sized morphological structures affect the performance, deformation/failure behavior at larger length scales. In addition, cementitious materials undergo chemical and morphological changes gaining strength during the transient hydration process. Hydration in cement is a very complex process creating complex microstructures and the associated molecular structures that vary with hydration. A fundamental understanding can be gained through multi-scale level modeling for the behavior and properties of cementitious materials starting from the material chemistry level atomistic scale to further explore their role and the manifested effects at larger length and engineering scales. This predictive modeling enables the understanding, and studying the influence of material chemistry level changes and nanomaterial additives on the expected resultant material characteristics and deformation behavior. Atomistic-molecular dynamic level modeling is required to couple material science to engineering mechanics. Starting at the molecular level a comprehensive description of the material’s chemistry is required to understand the fundamental properties that govern behavior occurring across each relevant length scale. Material chemistry level models and molecular dynamics modeling and simulations are employed in our work to describe the molecular-level chemistry features of calcium-silicate-hydrate (CSH), one of the key hydrated constituents of cement paste, their associated deformation and failure. The molecular level atomic structure for CSH can be represented by Jennite mineral structure. Jennite has been widely accepted by researchers and is typically used to represent the molecular structure of the CSH gel formed during the hydration of cement clinkers. This paper will focus on our recent work on the shear and compressive deformation and failure behavior of CSH represented by Jennite mineral structure that has been widely accepted by researchers and is typically used to represent the molecular structure of CSH formed during the hydration of cement clinkers. The deformation and failure behavior under shear and compression loading deformation in traditional hydrated CSH; effect of material chemistry changes on the predicted stress-strain behavior, transition from linear to non-linear behavior and identify the on-set of failure based on material chemistry structures of CSH Jennite and changes in its chemistry structure will be discussed.

Keywords: cementitious materials, deformation, failure, material chemistry modeling

Procedia PDF Downloads 285

Authors: Ali Abdul Kadhim, Fue Lien

Abstract:

Solid particle distribution on an impingement surface has been simulated utilizing a graphical processing unit (GPU). In-house computational fluid dynamics (CFD) code has been developed to investigate a 3D turbulent impinging jet using the lattice Boltzmann method (LBM) in conjunction with large eddy simulation (LES) and the multiple relaxation time (MRT) models. This paper proposed an improvement in the LBM-cellular automata (LBM-CA) probabilistic method. In the current model, the fluid flow utilizes the D3Q19 lattice, while the particle model employs the D3Q27 lattice. The particle numbers are defined at the same regular LBM nodes, and transport of particles from one node to its neighboring nodes are determined in accordance with the particle bulk density and velocity by considering all the external forces. The previous models distribute particles at each time step without considering the local velocity and the number of particles at each node. The present model overcomes the deficiencies of the previous LBM-CA models and, therefore, can better capture the dynamic interaction between particles and the surrounding turbulent flow field. Despite the increasing popularity of LBM-MRT-CA model in simulating complex multiphase fluid flows, this approach is still expensive in term of memory size and computational time required to perform 3D simulations. To improve the throughput of each simulation, a single GeForce GTX TITAN X GPU is used in the present work. The CUDA parallel programming platform and the CuRAND library are utilized to form an efficient LBM-CA algorithm. The methodology was first validated against a benchmark test case involving particle deposition on a square cylinder confined in a duct. The flow was unsteady and laminar at Re=200 (Re is the Reynolds number), and simulations were conducted for different Stokes numbers. The present LBM solutions agree well with other results available in the open literature. The GPU code was then used to simulate the particle transport and deposition in a turbulent impinging jet at Re=10,000. The simulations were conducted for L/D=2,4 and 6, where L is the nozzle-to-surface distance and D is the jet diameter. The effect of changing the Stokes number on the particle deposition profile was studied at different L/D ratios. For comparative studies, another in-house serial CPU code was also developed, coupling LBM with the classical Lagrangian particle dispersion model. Agreement between results obtained with LBM-CA and LBM-Lagrangian models and the experimental data is generally good. The present GPU approach achieves a speedup ratio of about 350 against the serial code running on a single CPU.

Keywords: CUDA, GPU parallel programming, LES, lattice Boltzmann method, MRT, multi-phase flow, probabilistic model

Procedia PDF Downloads 205

Authors: Camille Plant, Katherine McGill, Pek Ang

Abstract:

Oncology patients face a host of unique challenges, which are physical, psychological and philosophical in nature. This preliminary study aimed to explore the psychiatric morbidity of oncology patients in an outpatient setting at a major public hospital in Australia. The study found that 33 patients were referred to a Psychiatrist by a Clinical Psychologist or treating Oncologist. These patients attended an outpatient Psychiatry appointment at the Calvary Mater Hospital, Newcastle, over a 7 month period (June 2017-January 2018). Of these, 45% went on to have a follow-up appointment. The Clinical Global Impressions Scale (CGI) was used to gather symptom severity scores at baseline and at follow-up. The CGI is a clinician determined instrument that provides an assessment of global functioning. It is comprised of two companion one-item measures: the CGI-Severity (CGI-S) rates mental illness severity, and the CGI-Improvement (CGI-I) rates change in condition or improvement from initiation of treatment. Patients referred to a Psychiatrist were observed to be on average in the Markedly ill approaching Severely ill range (CGI-S average of 5.5). However, those patients who attended a follow-up appointment were on average only Moderately Ill at baseline (CGI-S average of 3.9). Despite these follow patients not being severely mentally ill initially, the contact was helpful, as their CGI-S scores improved on average to the Mildly Ill range (CGI-S average of 2.8). A Mixed ANOVA revealed that there was a significant improvement in mental illness severity post-follow-up appointment (Greenhouse-Geisser .000). There was a near even proportion of males and females attending appointments (58% female), and slightly more females attended a follow-up (60% female). Males were on average more mentally ill at baseline compared to females at baseline (male average M=3.86, female average M=3.56), and males had a greater reduction in mental illness severity on average compared to females (male average M=2.71, female average 3.00). This was approaching significance (.073) and would be important to explore with a larger sample size. Change in clinical condition for follow-up patients was also recorded. It was found that more than half of patients (53%) were observed to experience Minimal improvement in attending at least one follow-up appointment. There was no change for 27% of patients, and there were no patients who were worse at follow up. As this was a preliminary study with small sample size, future research conducted could explore whether there are any significant gender differences, such as whether males experience the significantly greater reduction in symptoms of mental illness compared to females, as well as any effects of cancer stage or type on psychiatric outcomes. Future research could also investigate outcomes for those patients who concurrently access a Clinical Psychologist alongside the Psychiatrist. A limitation of the study is that the outcome measure is a brief item rating completed by the clinician.

Keywords: clinical global impressions scale, psychiatry, morbidity, oncology, outcomes, psychiatry

Procedia PDF Downloads 145

Authors: Piotr Wisniewski, Sławomir Dykas

Abstract:

Condensation has a negative impact on turbomachinery efficiency in many energy processes.In technical applications, it is often impossible to dry the working fluid at the nozzle inlet. One of the most popular working fluid is atmospheric air that always contains water in form of steam, liquid, or ice crystals. Moreover, it always contains some amount of suspended particles which influence the phase change process. It is known that the phenomena of evaporation or condensation are connected with release or absorption of latent heat, what influence the fluid physical properties and might affect the machinery efficiency therefore, the phase transition has to be taken under account. This researchpresents an attempt to evaluate the impact of solid and liquid particles suspended in the air on the expansion of moist air in a low expansion rate, i.e., with expansion rate, P≈1000s⁻¹. The numerical study supported by analytical and experimental research is presented in this work. The experimental study was carried out using an in-house experimental test rig, where nozzle was examined for different inlet air relative humidity values included in the range of 25 to 51%. The nozzle was tested for a supersonic flow as well as for flow with shock waves induced by elevated back pressure. The Schlieren photography technique and measurement of static pressure on the nozzle wall were used for qualitative identification of both condensation and shock waves. A numerical model validated against experimental data available in the literature was used for analysis of occurring flow phenomena. The analysis of the suspended particles number, diameter, and character (solid or liquid) revealed their connection with heterogeneous condensation importance. If the expansion of fluid without suspended particlesis considered, the condensation triggers so called condensation wave that appears downstream the nozzle throat. If the solid particles are considered, with increasing number of them, the condensation triggers upwind the nozzle throat, decreasing the condensation wave strength. Due to the release of latent heat during condensation, the fluid temperature and pressure increase, leading to the shift of normal shock upstream the flow. Owing relatively large diameters of the droplets created during heterogeneous condensation, they evaporate partially on the shock and continues to evaporate downstream the nozzle. If the liquid water particles are considered, due to their larger radius, their do not affect the expanding flow significantly, however might be in major importance while considering the compression phenomena as they will tend to evaporate on the shock wave. This research proves the need of further study of phase change phenomena in supersonic flow especially considering the interaction of droplets with the aerodynamic waves in the flow.

Keywords: aerodynamics, computational fluid dynamics, condensation, moist air, multi-phase flows

Procedia PDF Downloads 116

Authors: Ashir Ahmed

Abstract:

Generally, radicalization happens when a person's thinking and behaviour become significantly different from how most of the members of their society and community view social issues and participate politically. Radicalization often leads to violent extremism that refers to the beliefs and actions of people who support or use violence to achieve ideological, religious or political goals. Studies on radicalization negate the common myths that someone must be in a group to be radicalised or anyone who experiences radical thoughts is a violent extremist. Moreover, it is erroneous to suggest that radicalisation is always linked to religion. Generally, the common motives of radicalization include ideological, issue-based, ethno-nationalist or separatist underpinning. Moreover, there are number of factors that further augments the chances of someone being radicalised and may choose the path of violent extremism and possibly terrorism. Since there are numbers of factors (and sometimes quite different) contributing in radicalization and violent extremism, it is highly unlikely to devise a single solution that could produce effective outcomes to deal with radicalization, violent extremism and terrorism. The pathway to deradicalization, like the pathway to radicalisation, is different for everyone. Considering the need of having customized deradicalization resolution, this study proposes a multi-tier framework, called ‘pyramid of deradicalization’ that first help identifying the stage at which an individual could be on the radicalization pathway and then propose a customize strategy to deal with the respective stage. The first tier (tier 1) addresses broader community and proposes a ‘universal approach’ aiming to offer community-based design and delivery of educational programs to raise awareness and provide general information on possible factors leading to radicalization and their remedies. The second tier focuses on the members of community who are more vulnerable and are disengaged from the rest of the community. This tier proposes a ‘targeted approach’ targeting the vulnerable members of the community through early intervention such as providing anonymous help lines where people feel confident and comfortable in seeking help without fearing the disclosure of their identity. The third tier aims to focus on people having clear evidence of moving toward extremism or getting radicalized. The people falls in this tier are believed to be supported through ‘interventionist approach’. The interventionist approach advocates the community engagement and community-policing, introducing deradicalization programmes to the targeted individuals and looking after their physical and mental health issues. The fourth and the last tier suggests the strategies to deal with people who are actively breaking the law. ‘Enforcement approach’ suggests various approaches such as strong law enforcement, fairness and accuracy in reporting radicalization events, unbiased treatment by law based on gender, race, nationality or religion and strengthen the family connections.It is anticipated that the operationalization of the proposed framework (‘pyramid of deradicalization’) would help in categorising people considering their tendency to become radicalized and then offer an appropriate strategy to make them valuable and peaceful members of the community.

Keywords: deradicalization, framework, terrorism, violent extremism

Procedia PDF Downloads 269

Authors: Linta Rose, Prasad K. Bhaskaran

Abstract:

Water-level information along the coast is very important for disaster management, navigation, planning shoreline management, coastal engineering and protection works, port and harbour activities, and for a better understanding of near-shore ocean dynamics. The water-level variation along a coast attributes from various factors like astronomical tides, meteorological and hydrological forcing. The study area is the Head Bay of Bengal which is highly vulnerable to flooding events caused by monsoons, cyclones and sea-level rise. The study aims to explore the extent to which wind and surface pressure can influence water-level elevation, in view of the low-lying topography of the coastal zones in the region. The ADCIRC hydrodynamic model has been customized for the Head Bay of Bengal, discretized using flexible finite elements and validated against tide gauge observations. Monthly mean climatological wind and mean sea level pressure fields of ERA Interim reanalysis data was used as input forcing to simulate water-level variation in the Head Bay of Bengal, in addition to tidal forcing. The output water-level was compared against that produced using tidal forcing alone, so as to quantify the contribution of meteorological forcing to water-level. The average contribution of meteorological fields to water-level in January is 5.5% at a deep-water location and 13.3% at a coastal location. During the month of July, when the monsoon winds are strongest in this region, this increases to 10.7% and 43.1% respectively at the deep-water and coastal locations. The model output was tested by varying the input conditions of the meteorological fields in an attempt to quantify the relative significance of wind speed and wind direction on water-level. Under uniform wind conditions, the results showed a higher contribution of meteorological fields for south-west winds than north-east winds, when the wind speed was higher. A comparison of the spectral characteristics of output water-level with that generated due to tidal forcing alone showed additional modes with seasonal and annual signatures. Moreover, non-linear monthly mode was found to be weaker than during tidal simulation, all of which point out that meteorological fields do not cause much effect on the water-level at periods less than a day and that it induces non-linear interactions between existing modes of oscillations. The study signifies the role of meteorological forcing under fair weather conditions and points out that a combination of multiple forcing fields including tides, wind, atmospheric pressure, waves, precipitation and river discharge is essential for efficient and effective forecast modelling, especially during extreme weather events.

Keywords: ADCIRC, head Bay of Bengal, mean sea level pressure, meteorological forcing, water-level, wind

Procedia PDF Downloads 217