Search results for: software ecosystem

Authors: Benaliouche Hana, Abdessemed Djamal, Meniai Abdessalem, Lesage Geoffroy, Heran Marc

Abstract:

This paper presents a dynamic mathematical model of activated sludge which is able to predict the formation and degradation kinetics of SMP (Soluble microbial products) in membrane bioreactor systems. The model is based on a calibrated version of ASM1 with the theory of production and degradation of SMP. The model was calibrated on the experimental data from MBR (Mathematical modeling Membrane bioreactor) pilot plant. Analytical expressions have been developed, describing the concentrations of the main state variables present in the sludge matrix, with the inclusion of only six additional linear differential equations. The objective is to present a new dynamic mathematical model of activated sludge capable of predicting the formation and degradation kinetics of SMP (UAP and BAP) from the submerged membrane bioreactor (BRMI), operating at low organic load (C / N = 3.5), for two sludge retention times (SRT) fixed at 40 days and 60 days, to study their impact on membrane fouling, The modeling study was carried out under the steady-state condition. Analytical expressions were then validated by comparing their results with those obtained by simulations using GPS-X-Hydromantis software. These equations made it possible, by means of modeling approaches (ASM1), to identify the operating and kinetic parameters and help to predict membrane fouling.

Keywords: Activated Sludge Model No. 1 (ASM1), mathematical modeling membrane bioreactor, soluble microbial products, UAP, BAP, Modeling SMP, MBR, heterotrophic biomass

Procedia PDF Downloads 268

Authors: Souhir Chelly, Chahida Harizi, Aicha Hechaichi, Sihem Aissaoui, Leila Ben Ayed, Maha Bergaoui, Mohamed Kouni Chahed

Abstract:

Introduction: The International Classification of Primary Care (ICPC) is part of the morbidity classification system. It had 17 chapters, and each is coded by an alphanumeric code: the letter corresponds to the chapter, the number to a paragraph in the chapter. The objective of this study is to show the utility of this classification in the coding of the reasons for demand for care in Primary health care (PHC), its advantages and limits. Methods: This is a cross-sectional descriptive study conducted in 4 PHC in Ariana district. Data on the demand for care during 2 days in the same week were collected. The coding of the information was done according to the CISP. The data was entered and analyzed by the EPI Info 7 software. Results: A total of 523 demands for care were investigated. The patients who came for the consultation are predominantly female (62.72%). Most of the consultants are young with an average age of 35 ± 26 years. In the ICPC, there are 7 rubrics: 'infections' is the most common reason with 49.9%, 'other diagnoses' with 40.2%, 'symptoms and complaints' with 5.5%, 'trauma' with 2.1%, 'procedures' with 2.1% and 'neoplasm' with 0.3%. The main advantage of the ICPC is the fact of being a standardized tool. It is very suitable for classification of the reasons for demand for care in PHC according to their specificity, capacity to be used in a computerized medical file of the PHC. Its current limitations are related to the difficulty of classification of some reasons for demand for care. Conclusion: The ICPC has been developed to provide healthcare with a coding reference that takes into account their specificity. The CIM is in its 10th revision; it would gain from revision to revision to be more efficient to be generalized and used by the teams of PHC.

Keywords: international classification of primary care, medical file, primary health care, Tunisia

Procedia PDF Downloads 247

Authors: Ainolnaim Azizol, Valerie Ross

Abstract:

Music is as old as mankind and rituals using music such as Kavadi have been associated with social, cultural, and spiritual practices in many traditional and modern societies. Recent literature has provided scientific evidence that music affects psychological and physical changes through stimulation of brainwave. Despite such advances, the scientific study of the sonic qualities peculiar to traditional instruments and how it impacts on ritualistic activities is still lacking. This study addresses one such phenomenon. Devotees in Kavadi rituals are known to be in a state of trance state and do not experience pain nor suffer injury despite the hundreds of needles pierced through their skins. Although scientists have sought to understand how this is possible, lesser is known about the music that is used to prepare devotees to enter into the trance state. This study fills this gap of knowledge by providing scientific evidence through the identification and mapping of the sonic spectrum or sound fingerprint of the instruments and the repertoire used in these ritualistic forms in their ethnographic environment and in audio-controlled situations. The objectives are to identify and categorize the different types of traditional music used in Kavadi rituals; to record, transcribe and digitally score the musical repertoire used in the oral tradition of Kavadi rituals; to map the sonic spectrum of ritual music using spectromography and advanced music analytical software a mixed methodology will be used. This comprises ethnographic field studies using interviews, participant observation, audio-video recordings and audio-methodology using spectromography and advanced audio-technology for sonic mapping and the transcription of audio recordings into digital scores.

Keywords: sonic, traditional, ritual, Kavadi, music

Procedia PDF Downloads 228

Authors: Anastasios Papathanasiou, George Liontos, Athanasios Katsouras, Vasiliki Liagkou, Euripides Glavas

Abstract:

Email remains a crucial communication tool due to its efficiency, accessibility and cost-effectiveness, enabling rapid information exchange across global networks. However, the global adoption of email has also made it a prime target for cyber threats, including phishing, malware and Business Email Compromise (BEC) attacks, which exploit its integral role in personal and professional realms in order to perform fraud and data breaches. To combat these threats, this research advocates for a multi-layered defense strategy incorporating advanced technological tools such as anti-spam and anti-malware software, machine learning algorithms and authentication protocols. Moreover, we developed an artificial intelligence model specifically designed to analyze email headers and assess their security status. This AI-driven model examines various components of email headers, such as "From" addresses, ‘Received’ paths and the integrity of SPF, DKIM and DMARC records. Upon analysis, it generates comprehensive reports that indicate whether an email is likely to be malicious or benign. This capability empowers users to identify potentially dangerous emails promptly, enhancing their ability to avoid phishing attacks, malware infections and other cyber threats.

Keywords: email security, artificial intelligence, header analysis, threat detection, phishing, DMARC, DKIM, SPF, ai model

Procedia PDF Downloads 27

Authors: Yousef Sharrab, Dimah Al-Fraihat, Monther Tarawneh, Aysh Alhroob, Ala’ Khalifeh, Nabil Sarhan

Abstract:

This paper explores the evolution of Electrical Engineering (EE) and Computer Science (CS) education in higher learning, examining the feasibility of unifying them into Electrical Engineering and Computer Science (EECS) for the technology industry. It delves into the historical reasons for their separation and underscores the need for integration. Emerging technologies such as AI, Virtual Reality, IoT, Cloud Computing, and Cybersecurity demand an integrated EE and CS program to enhance students' understanding. The study evaluates curriculum integration models, drawing from prior research and case studies, demonstrating how integration can provide students with a comprehensive knowledge base for industry demands. Successful integration necessitates addressing administrative and pedagogical challenges. For academic institutions considering merging EE and CS programs, the paper offers guidance, advocating for a flexible curriculum encompassing foundational courses and specialized tracks in computer engineering, software engineering, bioinformatics, information systems, data science, AI, robotics, IoT, virtual reality, cybersecurity, and cloud computing. Elective courses are emphasized to keep pace with technological advancements. Implementing this integrated approach can prepare students for success in the technology industry, addressing the challenges of a technologically advanced society reliant on both EE and CS principles. Integrating EE and CS curricula is crucial for preparing students for the future.

Keywords: electrical engineering, computer science, EECS, curriculum integration of EE and CS

Procedia PDF Downloads 39

Authors: Christina Zourna, Ioanna Papavassiliou-Alexiou

Abstract:

The purpose of this multi-phased action research PhD study in Greece was to investigate if and how Drama in Education (DiE) – used as an innovative group counselling method – may have positive effects on secondary education students’career self-efficacy and career decision-making skills development. Using both quantitative and qualitative research tools, high quality data were gathered at various stages of the research and were analysed through multivariate methods and open-source computer aided data analysis software such as R Studio, QualCoder, and SPSS packages. After a five-month-long educational intervention based on DiE method, it was found that 9th, 10th, and 11th gradersameliorated their self-efficacy and learned the process of making an informed career decision – through targeted information gathering about themselves and possible study paths – thus, developing career problem-solving and career management skills. Gender differences were non statistically important, while differences in grades showed a minor influence on some of the measured factorssuch as general career indecisiveness and self-evaluation. Students in the 11th grade scored significantly higher than younger students in the career self-efficacy scale and have stronger faith in their abilities e.g., choosing general over vocational school and major study orientation. The study has shown that DiE can be effective in group career guidance, especially concerning the pillars of self-awareness, self-efficacy, and career decision-making processes.

Keywords: career decision-making skills, career self-efficacy, CDDQ scale, CDMSE-SF scale, drama in education method

Procedia PDF Downloads 107

Authors: Waqed H. Almohammed, Mohammed Y. Fattah, Sajjad E. Rasheed

Abstract:

Dynamic traffic loads cause deformation of underground pipes, resulting in vehicle discomfort. This makes it necessary to reinforce the layers of soil above underground pipes. In this study, the subbase layer was reinforced. Finite element software (PLAXIS 3D) was used to in the simulation, which includes geocell reinforcement, vehicle loading, soil layers and Glass Fiber Reinforced Plastic (GRP) pipe. Geocell reinforcement was modeled using a geogrid element, which was defined as a slender structure element that has the ability to withstand axial stresses but not to resist bending. Geogrids cannot withstand compression but they can withstand tensile forces. Comparisons have been made between the numerical models and experimental works, and a good agreement was obtained. Using the mathematical model, the performance of three different pipes of diameter 600 mm, 800 mm, and 1000 mm, and three different vehicular speeds of 20 km/h, 40 km/h, and 60 km/h, was examined to determine their impact on surface settlement and vertical pressure at the pipe crown for two cases: with and without geocell reinforcement. The results showed that, for a pipe diameter of 600 mm under geocell reinforcement, surface settlement decreases by 94 % when the speed of the vehicle is 20 km/h and by 98% when the speed of the vehicle is 60 km/h. Vertical pressure decreases by 81 % when the diameter of the pipe is 600 mm, while the value decreases to 58 % for a pipe with diameter 1000 mm. The results show that geocell reinforcement causes a significant and positive reduction in surface settlement and vertical stress above the pipe crown, leading to an increase in pipe safety.

Keywords: dynamic loading, finite element, geocell-reinforcement, GRP pipe, PLAXIS 3D, surface settlement

Procedia PDF Downloads 237

Authors: Charles Q. Yu, Victoria H. Fan, Ahmed F. Al-Qahtani, Ibraim Viera

Abstract:

Introduction: Over 12 million people are blind due to opacity of the cornea, the clear tissue forming the front of the eye. Current methods use plastic implants to produce a clear optical pathway into the eye but are limited by a high rate of complications. New implants utilizing completely inside-the-eye projection technology can overcome blindness due to scarring of the eye by producing images on the retina without need for a clear optical pathway into the eye and may be free of the complications of traditional treatments. However, the interior of the eye is a challenging location for the design of optical focusing systems which can produce a sufficiently high quality image. No optical focusing systems have previously been characterized for this purpose. Methods: 3 optical focusing systems for intraocular (inside the eye) projection were designed and then modeled with ray tracing software, including a pinhole system, a planoconvex, and an achromatic system. These were then constructed using off-the-shelf components and tested in the laboratory. Weight, size, magnification, depth of focus, image quality and brightness were characterized. Results: Image quality increased with complexity of system design, as did weight and size. A dual achromatic doublet optical system produced the highest image quality. The visual acuity equivalent achieved with this system was better than 20/200. Its weight was less than that of the natural human crystalline lens. Conclusions: We demonstrate for the first time that high quality images can be produced by optical systems sufficiently small and light to be implanted within the eye.

Keywords: focusing, projection, blindness, cornea , achromatic, pinhole

Procedia PDF Downloads 114

Authors: Waqas Mehdi, Muhammad Umar Hassan, Khadeeja Mustafa

Abstract:

Objective: Post-concussion syndrome (PCS) is a medical term used to point out the complicated combination of physical, emotional, cognitive and behavioral signs and symptoms associated with Mild Traumatic Brain Injury(mTBI). This study was conducted to assess the improvement or debilitating effect of behavioral therapy in addition to the conventional treatment and to document these results for increasing the efficiency of treatment provided to such cases. Method: This was primarily an interventional prospective cohort study which was conducted in the Department of Neurosurgery, Mayo Hospital Lahore. The sample size was 200 patients who were randomly distributed into two groups. The interventional group with Cognitive behavioral therapy was added in addition to the conventional treatment regimen and the Control group receiving only conventional treatment. Results were noted initially as well as after two weeks of the follow-up period. Data were subsequently analyzed by Statistical Package for Social Sciences (SPSS) software and associations worked out. Result and conclusion: Among the patients that were given therapy sessions along with conventional medicine, there was a significant improvement in the symptoms and their overall quality of life. It is also important to notice that the time period taken for these effects to wane is cut down by psychiatric solutions too. So we can conclude that CBT sessions not only speed up recovery in patients with post-concussion syndrome they also aid in the efficiency improvement in functional capability and quality of life.

Keywords: neurosurgery, CBT, PCS, mTBI

Procedia PDF Downloads 151

Authors: Hesham Abd Elkhalek, Sherif M. Hafez, Yasser M. El Fahham

Abstract:

Allocating limited budget to maintain bridge networks and selecting effective maintenance strategies for each bridge represent challenging tasks for maintenance managers and decision makers. In Egypt, bridges are continuously deteriorating. In many cases, maintenance works are performed due to user complaints. The objective of this paper is to develop a practical and reliable framework to manage the maintenance, repair, and rehabilitation (MR&R) activities of Bridges network considering performance and budget limits. The model solves an optimization problem that maximizes the average condition of the entire network given the limited available budget using Genetic Algorithm (GA). The framework contains bridge inventory, condition assessment, repair cost calculation, deterioration prediction, and maintenance optimization. The developed model takes into account multiple parameters including serviceability requirements, budget allocation, element importance on structural safety and serviceability, bridge impact on network, and traffic. A questionnaire is conducted to complete the research scope. The proposed model is implemented in software, which provides a friendly user interface. The framework provides a multi-year maintenance plan for the entire network for up to five years. A case study of ten bridges is presented to validate and test the proposed model with data collected from Transportation Authorities in Egypt. Different scenarios are presented. The results are reasonable, feasible and within acceptable domain.

Keywords: bridge management systems (BMS), cost optimization condition assessment, fund allocation, Markov chain

Procedia PDF Downloads 275

Authors: Rahul Shrivastava, Manish Tripathi, Mohmmad Yasir, Shailesh Singh

Abstract:

Life style changes and depletion in atmospheric ozone layer in recent decades lead to increase in skin cancer including both melanoma and nonmelanomas. Natural products which were obtained from different plant species have the potential of anti skin cancer activity. In regard of this, present study focuses the potential effect of Glycosmis pentaphylla against anti skin cancer activity. Different Phytochemical constituents which were present in the roots of Glycosmis pentaphylla were identified and were used as ligands after sketching of their structures with the help of ACD/Chemsketch. These ligands are screened for their anticancer potential with proteins which are involved in skin cancer effects with the help of pyrx software. After performing docking studies, results reveal that Noracronycine secondary metabolite of Glycosmis pentaphylla shows strong affinity of their binding energy with Ribosomal S6 Kinase 2 (2QR8) protein. Ribosomal S6 Kinase 2 (2QR8) has an important role in the cell proliferation and transformation mediated through by N-terminal kinase domain and was induced by the tumour promoters such as epidermal growth factor. It also plays a key role in the neoplastic transformation of human skin cells and in skin cancer growth. Noracronycine interact with THR-493 and MET-496 residue of Ribosomal S6 Kinase 2 protein with binding energy ΔG = -8.68 kcal/mole. Thus on the basis of this study we can say that Noracronycine which present in roots of Glycosmis pentaphylla can be used as lead compound against skin cancer.

Keywords: glycosmis pentaphylla, pyrx, ribosomal s6 kinase, skin cancer

Procedia PDF Downloads 289

Authors: Sanusi Abubakar Sadiq

Abstract:

Despite the significance of tourism as a key revenue earner and employment generator, it is still being disregarded in many areas. The prospects of existing resources could boost development in communities; region, etc. are less used. This study is carried out with the view of developing Pandi-Tekki in Tanglang in Billiri Local Government Area as a Tourism Destination. It was primarily aimed at identifying features of Pandi-Tekki that could be developed into tourism attraction and suggest ways of developing the prospective site into a tourism destination, as well as exploring its possible contribution to tourism sector in Gombe State. Literature was reviewed based on relevant published materials. Data was collected through the use of qualitative and quantitative methods which include personal observation and structured questionnaire. Data was analyzed using the statistical package for the social sciences (SPSS) software. Result based on the data collected shows that Pandi-Tekki has potentials that can be developed as an attraction. The result also shows that the local community perceives tourism as a good development that will open them up to the entire world and also generate revenue to stimulate their economy. Conclusions were drawn based on the findings with regard to the analysis carried out in this research. It was discovered that Pandi-Tekki can be developed as a tourism destination, and there will be a great success towards achieving the aim and objectives of the development. Therefore, recommendations were made on creating awareness on the need to develop Pandi-Tekki as a Tourism Destination and the need for government to provide tourism facilities at the destination since it is a public outfit.

Keywords: attraction, destination, developing, features

Procedia PDF Downloads 268

Authors: Mahmoud Y. Shokry, Rami M. El-Sherbiny

Abstract:

This paper aims to highlight the role of some parameters that may be of a noticeable impact on numerical analysis/design of embankments. It presents the results of a three-dimensional (3-D) finite element analysis of a monitored earth embankment that was constructed on soft clay formation stabilized by cast in-situ piles using software PLAXIS 3D. A comparison between the predicted and the monitored responses is presented to assess the adequacy of the adopted numerical model. The model was used in the targeted parametric study. Moreover, a comparison was performed between the results of the 3-D analyses and the analytical solutions. This paper concluded that the effect of using mono pile caps led to decrease both the total and differential settlement and increased the efficiency of the piled embankment system. The study of using geogrids revealed that it can contribute in decreasing the settlement and maximizing the part of the embankment load transferred to piles. Moreover, it was found that increasing the stiffness of the geogrids provides higher values of tensile forces and hence has more effective influence on embankment load carried by piles rather than using multi-number of layers with low values of geogrid stiffness. The efficiency of the piled embankments system was also found to be greater when higher embankments are used rather than the low height embankments. The comparison between the numerical 3-D model and the theoretical design methods revealed that many analytical solutions are conservative and non-accurate rather than the 3-D finite element numerical models.

Keywords: efficiency, embankment, geogrids, soft clay

Procedia PDF Downloads 308

Authors: Rana Alaa El-Deen Ahmed, M. Elemam Shehab, Shereen Morsy, Nermeen Mekawie

Abstract:

With the growing popularity and acceptance of e-commerce platforms, users face an ever increasing burden in actually choosing the right product from the large number of online offers. Thus, techniques for personalization and shopping guides are needed by users. For a pleasant and successful shopping experience, users need to know easily which products to buy with high confidence. Since selling a wide variety of products has become easier due to the popularity of online stores, online retailers are able to sell more products than a physical store. The disadvantage is that the customers might not find products they need. In this research the customer will be able to find the products he is searching for, because recommender systems are used in some ecommerce web sites. Recommender system learns from the information about customers and products and provides appropriate personalized recommendations to customers to find the needed product. In this paper eleven classification algorithms are comparatively tested to find the best classifier fit for consumer online shopping attitudes and behavior in the experimented dataset. The WEKA knowledge analysis tool, which is an open source data mining workbench software used in comparing conventional classifiers to get the best classifier was used in this research. In this research by using the data mining tool (WEKA) with the experimented classifiers the results show that decision table and filtered classifier gives the highest accuracy and the lowest accuracy classification via clustering and simple cart.

Keywords: classification, data mining, machine learning, online shopping, WEKA

Procedia PDF Downloads 337

Authors: B. Arzhanov, A. Correia, P. Delgado, J. Meireles

Abstract:

Due to the higher power loss levels in electronic components, the thermal design of PCBs (Printed Circuit Boards) of an assembled device becomes one of the most important quality factors in electronics. Nonetheless, some of leading causes of the microelectronic component failures are due to higher temperatures, the leakages or thermal-mechanical stress, which is a concern, is the reliability of microelectronic packages. This article presents an experimental approach to measure the junction temperature of exposed pad packages. The implemented solution is in a prototype phase, using a temperature-sensitive parameter (TSP) to measure temperature directly on the die, validating the numeric results provided by the Mechanical APDL (Ansys Parametric Design Language) under same conditions. The physical device-under-test is composed by a Thermal Test Chip (TTC-1002) and assembly in a QFN cavity, soldered to a test-board according to JEDEC Standards. Monitoring the voltage drop across a forward-biased diode, is an indirectly method but accurate to obtain the junction temperature of QFN component with an applied power range between 0,3W to 1.5W. The temperature distributions on the PCB test-board and QFN cavity surface were monitored by an infra-red thermal camera (Goby-384) controlled and images processed by the Xeneth software. The article provides a set-up to monitorize in real-time the junction temperature of ICs, namely devices with the exposed pad package (i.e. QFN). Presenting the PCB layout parameters that the designer should use to improve thermal performance, and evaluate the impact of voids in solder interface in the device junction temperature.

Keywords: quad flat no-Lead packages, exposed pads, junction temperature, thermal management and measurements

Procedia PDF Downloads 273

Authors: Paschal A. Ochang, Emmanuel C. Oji

Abstract:

The Duffing’s Equation is a second order system that is very important because they are fundamental to the behaviour of higher order systems and they have applications in almost all fields of science and engineering. In the biological area, it is useful in plant stem dependence and natural frequency and model of the Brain Crash Analysis (BCA). In Engineering, it is useful in the study of Damping indoor construction and Traffic lights and to the meteorologist it is used in the prediction of weather conditions. However, most Problems in real life that occur are non-linear in nature and may not have analytical solutions except approximations or simulations, so trying to find an exact explicit solution may in general be complicated and sometimes impossible. Therefore we aim to find out if it is possible to obtain one analytical fixed point to the non-linear ordinary equation using fixed point analytical method. We started by exposing the scope of the Duffing’s equation and other related works on it. With a major focus on the fixed point and fixed point iterative scheme, we tried different iterative schemes on the Duffing’s Equation. We were able to identify that one can only see the fixed points to a Damped Duffing’s Equation and not to the Undamped Duffing’s Equation. This is because the cubic nonlinearity term is the determining factor to the Duffing’s Equation. We finally came to the results where we identified the stability of an equation that is damped, forced and second order in nature. Generally, in this research, we approximate the solution of Duffing’s Equation by converting it to a system of First and Second Order Ordinary Differential Equation and using Fixed Point Iterative approach. This approach shows that for different versions of Duffing’s Equations (damped), we find fixed points, therefore the order of computations and running time of applied software in all fields using the Duffing’s equation will be reduced.

Keywords: damping, Duffing's equation, fixed point analysis, second order differential, stability analysis

Procedia PDF Downloads 268

Authors: M. B. Ricardo De Oliveira, A. Borghi-Silva, L. Di Thommazo, D. Braatz

Abstract:

Prototypes can be understood as representations of a product concept. Furthermore, prototyping consists in an important stage in product development and results in better team communication, decision making, testing and problem solving through feedback. Although there are several methods of prototyping suggested by recent studies for designers to choose from, some methods present different advantages, such as cost and time reduction, performance and fidelity, which should be taken in account during a product development project. In this multidisciplinary study, involving areas of physiotherapy, engineering and computer science (hardware and software), we compared four developed prototypes of an ergometric step: a virtual prototype, a 3D printed prototype, a bricolage prototype and a prototype manufactured by a third-party company. These prototypes were evaluated in a comparative-qualitative approach for their contribution to the concept’s maturation of the product, the different prototyping methods used and the advantages and disadvantages of each one based on the product’s design specifications (performance, safety, materials, cost, maintenance, usability, ergonomics and portability). Our results indicated that despite prototypes show overall advantages, all of them have limitations, thus being crucial to have different methods of testing and interacting with the product. Additionally, virtual and 3D printed prototypes were essential at early stages of the project due to their low-cost and high-fidelity representation of the product, while the prototype manufactured by a third-party company and bricolage prototype introduced functional tests in real scenarios, allowing more detailed evaluations. This study also resulted in a patent for an ergometric step.

Keywords: Product Design, Product Development, Prototypes, Step

Procedia PDF Downloads 103

Authors: Rujnan Tuna, Ayse Cil Akinci

Abstract:

Work life takes up an important place in human life, and an employed person faces many stimuli from internal and external environments and is affected by them in a positive or negative way. Also, the handover process, which is the process of sharing information about the patient with other health professionals, is an important criterion to maintain patient care and enhance the quality of care provided. Handover is a key component for sustaining daily basic clinical practices and is also essential to maintain the safe patient care. This investigation followed a descriptive and correlation design in order to establish job stress and the handover efficiency of nurses and the relationship in between. The study was conducted with 192 nurses working in a public hospital in Istanbul between January and March 2017. Descriptive information form, Job Stressors Scale, and Handover Evaluation Scale were used to collect the data of the study. The data were analyzed by using IBM SPSS Statistics 22.0 statistical software. Approvals from participants, managers of institution, and ethics committee were taken for the study. As a result of the research, it was found that job stress was above the median value, and the highest score in the ‘work role conflict’ subdimension. Also, it was found that the effectiveness of the nurses' handover effectiviness was above the median value and the highest score in the ‘quality of information’ subdimension. In the study, there was a negatively weak correlation between ‘work role overload’ subdimension of Job Stressors Scale and ‘interaction and support’ subdimension of Handover Evaluation Scale. There is a need for further study in order to maintain patient safety.

Keywords: handover, job stress, nurse, patient

Procedia PDF Downloads 147

Authors: Savaş Durduran, Ceren Yağci

Abstract:

The nature of the events going on in the world, when people’s lives are considered significantly affects natural disasters. Considering thousands of years of earth history, it is seen that many natural disasters, particularly earthquakes located in our country. Behaving cautious, without occurring hazards, after being disaster is much easier and cost effective than returning to the normal life. The four phases of disaster management in the whole world has been described as; pre-disaster preparedness and mitigation, post-disaster response and rehabilitation studies. Pre-disaster and post-disaster phases has half the weight of disaster management. How much would be prepared for disaster, no matter how disaster damage reducing work gives important, we will be less harm from material and spiritual sense. To do this in a systematic way we use the Geographic Information Systems (GIS). The execution of the emergency services to be on time and emergency control mechanism against the development the most appropriate decision Geographic Information System GIS) can be useful. The execution of the emergency services to be on time and emergency control mechanism towards for developing to be the most appropriate decision Geographic Information System (GIS) can be useful. The results obtained by using products with GIS analysis of seismic data to the city, manager of the city required information and data that can be more healthy and satisfies the appropriate policy decisions can be produced. In this study, using ArcGIS software and benefiting reports of the earthquake that occurred in the Konya city, spatial and non-spatial data consisting databases created, by the help of this database a potential disaster management aimed in the city of Konya regard to urban earthquake, GIS-aided analyzes were performed.

Keywords: geographic information systems (GIS), disaster management, emergency control mechanism, Konya

Procedia PDF Downloads 456

Authors: Fouzieh Rouzmehr, Mehdi Mousavi

Abstract:

Hot mix asphalt concrete (HMAC) is a mixture of aggregates and bitumen. The primary ingredient that determines the mechanical properties of HMAC is the bitumen in it, which displays viscoelastic behavior under normal service conditions. For simplicity, asphalt concrete is considered an elastic material, but this is far from reality at high service temperatures and longer loading times. Viscoelasticity means that the material's stress-strain relationship depends on the strain rate and loading duration. The goal of this paper is to simulate the mechanical response of flexible pavements using linear elastic and viscoelastic modeling of asphalt concrete and predict pavement performance. Falling Weight Deflectometer (FWD) load will be simulated and the results for elastic and viscoelastic modeling will be evaluated. The viscoelastic simulation is performed by the Prony series, which will be modeled by using ANSYS software. Inflexible pavement design, tensile strain at the bottom of the surface layer and compressive strain at the top of the last layer plays an important role in the structural response of the pavement and they will imply the number of loads for fatigue (Nf) and rutting (Nd) respectively. The differences of these two modelings are investigated on fatigue cracking and rutting problem, which are the two main design parameters in flexible pavement design. Although the differences in rutting problem between the two models were negligible, in fatigue cracking, the viscoelastic model results were more accurate. Results indicate that modeling the flexible pavement with elastic material is efficient enough and gives acceptable results.

Keywords: flexible pavement, asphalt, FEM, viscoelastic, elastic, ANSYS, modeling

Procedia PDF Downloads 116

Authors: Jean Marie Vianney Ininahazwe, Patrick Bitangumutwenzi

Abstract:

Context: The issue of menstrual hygiene is an entry point for demonstrating the gender-specific nature of the needs of women and adolescent girls. Women and girls around the world face many challenges in managing their periods. They may be deprived of certain basic human rights, including those relating to education, work and health. This work describes the Knowledge, Attitudes and Practices of menstrual hygiene among adolescent girls from 12 to 19 years at Lake Tanganyika Secondary School. Method: This is a descriptive cross-sectional study among 384 adolescent girls from Lake Tanganyika secondary school over a period of 2 weeks from September 13 to September 27 and with a purely general objective of describing the Knowledge, Attitudes and Practices of menstrual hygiene in secondary schools. The study was conducted using a non-probability method and the sampling technique was for convenience. The data collection technique used was the survey by questionnaire and the exploitation of the documentary. The data collection tool used was the questionnaire. Microsoft Word 2013, Microsoft Excel 2.13 and EPI INFO7 software were used for this purpose. Results: We noticed that 55.47% of the participants knew that menstruation is a physiological process; 57.55% of the teenage girls surveyed get their information about menstrual hygiene from their mothers; 75.72% use sanitary napkins and 24.02% use fabrics as protective material; 35.16% of respondents have already lacked sanitary napkins since their menarche; 37.29% are absent from classes due to lack of sanitary napkins; 23.82% use soap and other products to wash.

Keywords: knowledge, attitudes, practices, menstrual hygiene

Procedia PDF Downloads 54

Authors: Jimmy Jiun-Ming Su, Yuan-Min Lin

Abstract:

Bioprinting has been applied to produce 3D cellular constructs for tissue engineering. Microextrusion printing is the most common used method. However, printing low viscosity bioink is a challenge for this method. Herein, we developed a new 3D printing system to fabricate cell-laden hydrogels via a DLP-based projector. The bioprinter is assembled from affordable equipment including a stepper motor, screw, LED-based DLP projector, open source computer hardware and software. The system can use low viscosity and photo-polymerized bioink to fabricate 3D tissue mimics in a layer-by-layer manner. In this study, we used gelatin methylacrylate (GelMA) as bioink for stem cell encapsulation. In order to reinforce the printed construct, surface modified hydroxyapatite has been added in the bioink. We demonstrated the silanization of hydroxyapatite could improve the crosslinking between the interface of hydroxyapatite and GelMA. The results showed that the incorporation of silanized hydroxyapatite into the bioink had an enhancing effect on the mechanical properties of printed hydrogel, in addition, the hydrogel had low cytotoxicity and promoted the differentiation of embedded human bone marrow stem cells (hBMSCs) and retinal pigment epithelium (RPE) cells. Moreover, this bioprinting system has the ability to generate microchannels inside the engineered tissues to facilitate diffusion of nutrients. We believe this 3D bioprinting system has potential to fabricate various tissues for clinical applications and regenerative medicine in the future.

Keywords: bioprinting, cell encapsulation, digital light processing, GelMA hydrogel

Procedia PDF Downloads 158

Authors: Maninderjeet K. Grewal, Sakshi Bhatnor, Renu Chadha

Abstract:

The composition of pharmaceutical entities and the molecular interactions can be altered to optimize drug properties such as solubility and bioavailability by the crystal engineering technique. The present work has emphasized on the preparation, characterization, and biopharmaceutical evaluation of co-crystal of BCS Class II anti-osteoarthritis drug, Oxaprozin (OXA) with aspartic acid (ASPA) as co-former. The co-crystals were prepared through the mechanochemical solvent drop grinding method. Characterization of the prepared co-crystal (OXA-ASPA) was done by using analytical tools such as differential scanning calorimetry (DSC), Fourier transform infrared spectroscopy (FT-IR), powder X-ray diffraction (PXRD). DSC thermogram of OXA-ASPA cocrystal showed a single sharp melting endotherm at 235 ºC, which was between the melting peaks of the drug and the counter molecules suggesting the formation of a new phase which is a co-crystal that was further confirmed by using other analytical techniques. FT-IR analysis of OXA-ASPA cocrystal showed a shift in a hydroxyl, carbonyl, and amine peaks as compared to pure drugs indicating all these functional groups are participating in cocrystal formation. The appearance of new peaks in the PXRD pattern of cocrystals in comparison to individual components showed that a new crystalline entity has been formed. The Crystal structure of cocrystal was determined using material studio software (Biovia) from PXRD. The equilibrium solubility study of OXA-ASPA showed improvement in solubility as compared to pure drug. Therefore, it was envisioned to prepare the co-crystal of oxaprozin with a suitable conformer to modulate its physiochemical properties and consequently, the biopharmaceutical parameters.

Keywords: cocrystals, coformer, oxaprozin, solubility

Procedia PDF Downloads 97

Authors: Sultan Al Shafian, Mozaher Ul Kabir, Khondoker Istiak Ahmad, Masnun Abrar, Mahfuza Khanum, Hossain M. Shahin

Abstract:

For structural evaluation of shallow foundation, the modulus of subgrade reaction is one of the most widely used and accepted parameter for its ease of calculations. To determine this parameter, one of the most common field method is Plate Load test method. In this field test method, the subgrade modulus is considered for a specific location and according to its application, it is assumed that the displacement occurred in one place does not affect other adjacent locations. For this kind of assumptions, the modulus of subgrade reaction sometimes forced the engineers to overdesign the underground structure, which eventually results in increasing the cost of the construction and sometimes failure of the structure. In the present study, the settlement of a shallow foundation has been analyzed using both conventional and numerical analysis. Around 25 plate load tests were conducted on a sand fill site in Bangladesh to determine the Modulus of Subgrade reaction of ground which is later used to design a shallow foundation considering different depth. After the collection of the field data, the field condition was appropriately simulated in a finite element software. Finally results obtained from both the conventional and numerical approach has been compared. A significant difference has been observed in the case of settlement while comparing the results. A proper correlation has also been proposed at the end of this research work between the two methods of in order to provide the most efficient way to calculate the subgrade modulus of the ground for designing the shallow foundation.

Keywords: modulus of subgrade reaction, shallow foundation, finite element analysis, settlement, plate load test

Procedia PDF Downloads 168

Authors: Ijaz Ahamad Tatlah

Abstract:

The justification of this study was to identify about physical facilities as encouragement to Quality Assurance Practices (QAP) in the Universities of Pakistan concerning the views of students, teachers and Directors of Quality Enhancement Cells’ (QEC’s) and to differentiate the views of students, teachers and Directors of QECs in relation to physical facilities about quality assurance practices in the universities of Pakistan. It was a quantitative and qualitative research study. This study was conducted on a sample of 28 universities (public and private sector) of Pakistan by using random and purposive sampling technique. Questionnaires and semi-structured interviews were planned to gather information from students, teachers and Directors of QECs in relation to physical facilities about quality assurance practices in the universities of Pakistan. The data was analyzed by using Descriptive, inferential statistics, and thematic coding. The study revealed that students, teachers and Directors of QEC’s faced a lot of problems and issues without physical facilities. Quality assurance Agency (QAA), Quality Assurance Department (QAD) and Higher Education commission (HEC) all are relevant Pakistani Agencies, which are working consistently of both sectors i.e. public and private to supervise, guide and facilitate the universities of Pakistan for developing quality assurance practices. Majority of the students teachers and Directors’ of QECs opined that books, research journals, manuals for use of science laboratories, equipment for experiments and update computers were available for teachers and students’ in the universities. It was suggested by the students teachers and Directors of QECs of universities that Quality Assurance Practices (QAP) can be accelerated by thinking the following steps: provision of sufficient resources, add the latest software for computers laboratories and new edition of books.

Keywords: physical facilities, quality assurance practices, library, laboratory

Procedia PDF Downloads 367

Authors: Mehdi Nasr Esfahani, Abdal-Rasool Gholamalian, Abdelfattah A. Dababat

Abstract:

Wheat, Triticum aestivum L. is one of the most important and strategic crops in the human diet. Several diseases threaten this particular crop. Common root rot disease of wheat by a fungal agent, Bipolaris sorokiniana is one of the important diseases, causing considerable losses worldwide. Resistant sources are the only feasible and effective method of control for managing diseases. In this study, the response of 33 domestic and exotic wheat genotypes, including cultivars and promising lines were screened to B. sorokiniana at greenhouse and field conditions, based on five scoring scale indexes of 0 to 100 severity percentage. The screening was continued on resistant wheat genotypes and repeated several times to confirm the greenhouse and field results. Statistical and cluster analysis of data was performed using SAS and SPSS software, respectively. The results showed that, the response of wheat genotypes to the disease in the greenhouse and field conditions was highly significant. The highest rate of common root rot disease infection, B. sorokiniana in the greenhouse and field, was of CVS. Karkheh and Beck Cross-Roshan with 60.83% and 59.16% disease severity respectively, and the lowest one were in cv. Alvand with 18.33%, followed by cv. Baharan with 19.16% disease severity, with a highly significant difference respectively. The remaining wheat genotypes were located in between these two highest and lowest infected groups to B. sorokiniana significantly. There was a high correlation coefficient between the related statistical groups and cluster analysis.

Keywords: wheat, rot, root, crown, fungus, genotype, resistance

Procedia PDF Downloads 121

Authors: Jalal Khan, Daniyal Ali Sehrai, Shakeel Ahmad

Abstract:

This paper presents the design and performance evaluation of multiband metamaterial based antenna operating in the 3.6 GHz (4G), 14.33 GHz, and 28.86 GHz (5G) frequency bands, for future mobile and handheld devices. The radiating element of the proposed design is made up of a conductive material supported by a 1.524 mm thicker Rogers-4003 substrate, having a relative dielectric constant and loss tangent of 3.55 and 0.0027, respectively. The substrate is backed by truncated ground plane. The future mobile communication system is based on higher frequencies, which are highly affected by the atmospheric conditions. Therefore, to overcome the path loss problem, essential enhancements and improvements must be made in the overall performance of the antenna. The traditional ground plane does not provide the in-phase reflection and surface wave suppression due to which side and back lobes are produced. This will affect the antenna performance in terms of gain and efficiency. To enhance the overall performance of the antenna, a metamaterial acting as a high impedance surface (HIS) is used as a reflector in the proposed design. The simulated gain of the metamaterial based antenna is enhanced from {2.76-6.47, 4.83-6.71 and 7.52-7.73} dB at 3.6, 14.33 and 28.89 GHz, respectively relative to the gain of the antenna backed by a traditional ground plane. The proposed antenna radiated efficiently with a radiated efficiency (>85 %) in all the three frequency bands with and without metamaterial surface. The total volume of the antenna is (L x W x h=45 x 40 x 1.524) mm³. The antenna can be potentially used for wireless handheld devices and mobile terminal. All the simulations have been performed using the Computer Simulation Technology (CST) software.

Keywords: CST MWS, fourth generation/fifth generation, 4G/5G, high gain, multiband, metamaterial

Procedia PDF Downloads 149

Authors: Yvette Nsabimana, Nadine Misago, Minani Methode

Abstract:

Context: the issue of menstrual hygiene is an entry point for demonstrating the gender-specific nature of the needs of women and adolescent girls. Women and girls around the world face many challenges in managing their periods. They may be deprived of certain basic human rights, including those relating to education, work and health. This work describes the Knowledge, Attitudes and Practices of menstrual hygiene among adolescent girls from 12 to 19 years of Lake Tanganyika Secondary School. Method: This is a descriptive cross-sectional study among 384 adolescent girls from Lake Tanganyika secondary school over a period of 2 weeks from September 13 to September 27 and with a purely general objective of describing the Knowledge, Attitudes and Practices of menstrual hygiene in secondary schools. The study was conducted using a non-probability method and the sampling technique was for convenience. The data collection technique used was the survey by questionnaire and the exploitation of the documentary. The data collection tool used was the questionnaire. Microsoft Word 2013, Microsoft Excel 2.13 and EPI INFO7 software were used for this purpose. Results: We noticed that 55.47% of the participants knew that menstruation is a physiological process; 57.55% of the teenage girls surveyed get their information about menstrual hygiene from their mothers; 75.72% use sanitary napkins and 24.02% use fabrics as protective material; 35.16% of respondents have already lacked sanitary napkins since their menarche; 37.29% are absent from classes due to lack of sanitary napkins; 23.82% use soap and other products to wash.

Keywords: knowledge, attitudes, practices, menstrual hygiene

Procedia PDF Downloads 59

Authors: S. Muogbo Uju, Akpunonu Uju,

Abstract:

The prevailing harsh environment factors couple with poverty rate and unemployment propels a high rate of entrepreneurial activities in developing countries of the world. Women entrepreneurs operate within gender bias among other constraint that can constitute a threat or create opportunity for women entrepreneurs. This empirical paper investigates and critically examines women entrepreneurship as an inventive approach to sustainable development in Anambra State. The study used descriptive statistics (frequencies, mean, and percentages) to answer the three research questions posed. Hypotheses testing were done with person product moment correlation and multiple regressions were employed in data analysis. SPSS [statistical package for Social Science] software was used to run the analysis. Three hundred and fifty three (353) copies of questionnaires were administered, and one hundred and forty six (146) copies were returned. Consequently, the findings of this study portrayed a significant impact between women entrepreneurship activities, job creation, wealth creation, youth empowerment, poverty reduction, employment generation, and increase in standard of livings of people. Therefore, the findings prescribe that government should ensure that managerial lessons are accompanied with the skill acquisition programs in order for them to understand the rudiment of owing and sustaining a business. The study also recommends that women entrepreneurs that have overcome the inertia of starting a business should come together to create platforms that can help those women who are yet to take a step or kick-start such venture.

Keywords: women entrepreneurship, skill acquisition, sustainability, wealth creation

Procedia PDF Downloads 424

Authors: Ogbonnaya O. Iroanya, Samson T. Fakorede, Osamudiamen J. Edosa, Hadiat A. Azeez

Abstract:

The human mitochondrial DNA (mtDNA) is about 17 kbp circular DNA fragments found within the mitochondria together with smaller fragments of 1200 bp known as the control region. Knowledge of variation within populations has been employed in forensic and molecular anthropology studies. The study was aimed at investigating the polymorphic nature of the two hypervariable segments (HVS) of the mtDNA, i.e., HVS1 and HVS2, and to determine the haplogroup distribution among individuals resident in Lagos, Southwestern Nigeria. Peripheral blood samples were obtained from sixty individuals who are not related maternally, followed by DNA extraction and amplification of the extracted DNA using primers specific for the regions under investigation. DNA amplicons were sequenced, and sequenced data were aligned and compared to the revised Cambridge Reference Sequence (rCRS) GenBank Accession number: NC_012920.1) using BioEdit software. Results obtained showed 61 and 52 polymorphic nucleotide positions for HVS1 and HVS2, respectively. While a total of three indels mutation were recorded for HVS1, there were seven for HVS2. Also, transition mutations predominate nucleotide change observed in the study. Genetic diversity (GD) values for HVS1 and HVS2 were estimated to be 84.21 and 90.4%, respectively, while random match probability was 0.17% for HVS1 and 0.89% for HVS2. The study also revealed mixed haplogroups specific to the African (L1-L3) and the Eurasians (U and H) lineages. New polymorphic sites obtained from the study are promising for human identification purposes.

Keywords: hypervariable region, indels, mitochondrial DNA, polymorphism, random match probability

Procedia PDF Downloads 102