Search results for: inclusive design

Authors: Vishal A. S. Salelkar, Sumitra S. Kandolkar

Abstract:

Golden ratio (ф) or Golden mean or Golden section, as it is often referred to, is a proportion or a mean, which is often used by architects while conceiving the aesthetics of a structure. Golden Ratio (ф) is an irrational number that can be roughly rounded to 1.618 and is derived out of quadratic equation x2-x-1=0. The use of Golden Ratio (ф) can be observed throughout history, as far as ancient Egyptians, which later peaked during the Greek golden age. The use of this design technique is very much prevalent. At present, architects around the world prefer this as one of the primary techniques to decide aesthetics. In this study, an analysis has been performed to investigate whether the use of the golden ratio while planning a structure has any effects on the seismic behavior of the structure. The structure is modeled and analyzed on ETABS (by Computers and Structures, Inc.) for Seismic requirements equivalent to Zone III (Region: Goa-India) as per Indian Standard Code IS-1893. The results were compared to that of an identical structure modeled along the lines of normal design philosophy, not using the Golden Ratio tools. The results were then compared for Story Shear, Story Drift, and Story Displacement Readings. Improvement in performance, although slight, but was observed. Similar improvements were also observed in subsequent iterations, performed using time-acceleration data of previous major earthquakes matched to Zone III as per IS-1893.

Keywords: ETABS, golden ratio, seismic design, structural behavior

Procedia PDF Downloads 154

Authors: O. Adjoul, A. Feugier, K. Benfriha, A. Aoussat

Abstract:

In general, issues related to design and maintenance are considered in an independent manner. However, the decisions made in these two sets influence each other. The design for maintenance is considered an opportunity to optimize the life cycle cost of a product, particularly in the nuclear or aeronautical field, where maintenance expenses represent more than 60% of life cycle costs. The design of large-scale systems starts with product architecture, a choice of components in terms of cost, reliability, weight and other attributes, corresponding to the specifications. On the other hand, the design must take into account maintenance by improving, in particular, real-time monitoring of equipment through the integration of new technologies such as connected sensors and intelligent actuators. We noticed that different approaches used in the Design For Maintenance (DFM) methods are limited to the simultaneous characterization of the reliability and maintainability of a multi-component system. This article proposes a method of DFM that assists designers to propose dynamic maintenance for multi-component industrial systems. The term "dynamic" refers to the ability to integrate available monitoring data to adapt the maintenance decision in real time. The goal is to maximize the availability of the system at a given life cycle cost. This paper presents an approach for simultaneous optimization of the design and maintenance of multi-component systems. Here the design is characterized by four decision variables for each component (reliability level, maintainability level, redundancy level, and level of monitoring data). The maintenance is characterized by two decision variables (the dates of the maintenance stops and the maintenance operations to be performed on the system during these stops). The DFM model helps the designers choose technical solutions for the large-scale industrial products. Large-scale refers to the complex multi-component industrial systems and long life-cycle, such as trains, aircraft, etc. The method is based on a two-level hybrid algorithm for simultaneous optimization of design and maintenance, using genetic algorithms. The first level is to select a design solution for a given system that considers the life cycle cost and the reliability. The second level consists of determining a dynamic and optimal maintenance plan to be deployed for a design solution. This level is based on the Maintenance Free Operating Period (MFOP) concept, which takes into account the decision criteria such as, total reliability, maintenance cost and maintenance time. Depending on the life cycle duration, the desired availability, and the desired business model (sales or rental), this tool provides visibility of overall costs and optimal product architecture.

Keywords: availability, design for maintenance (DFM), dynamic maintenance, life cycle cost (LCC), maintenance free operating period (MFOP), simultaneous optimization

Procedia PDF Downloads 98

Authors: Jenna Pyorala

Abstract:

This research looks at the principles and purposes ornamental design has served in the field of textile design. Ornamental designs are characterized by richness of details, abundance of elements, vegetative motifs and organic forms that flow harmoniously in complex compositions. Research on ornamental design is significant, because ornaments have been overlooked and considered as less meaningful and aesthetically pleasing than minimalistic, modern designs. This is despite the fact that in many parts of the world ornaments have been an important part of the cultural identification and expression for centuries. Ornament has been claimed to be superficial and merely used as a decorative way to hide the faults of designs. Such generalization is an incorrect interpretation of the real purposes of ornament. Many ornamental patterns tell stories, present mythological scenes or convey symbolistic meanings. Historically, ornamental decorations have been representing ideas and characteristics such as abundance, wealth, power and personal magnificence. The production of fine ornaments required refined skill, eye for intricate detail and perseverance while compiling complex elements into harmonious compositions. For this reason, ornaments have played an important role in the advancement of craftsmanship. Even though it has been claimed that people in the western design world have lost the relationship to ornament, the relation to it has merely changed from the practice of a craftsman to conceptualisation of a designer. With the help of new technological tools the production of ornaments has become faster and more efficient, demanding less manual labour. Designers who commit to this style of organic forms and vegetative motifs embrace and respect nature by representing its organically growing forms and by following its principles. The complexity of the designs is used as a way to evoke a sense of extraordinary beauty and stimulate intellect by freeing the mind from the predetermined interpretations. Through the study of these purposes it can be demonstrated that complex and richer design styles are as valuable a part of the world of design as more modern design approaches. The study highlights the meaning of ornaments by presenting visual examples and literature research findings. The practice based part of the project is the visual analysis of historical and cultural ornamental traditions such as Indian Chikan embroidery, Persian carpets, Art Nouveau and Rococo according to the rubric created for the purpose. The next step is the creation of ornamental designs based on the key elements in different styles. Theoretical and practical parts are woven together in this study that respects respect the long traditions of ornaments and highlight the importance of these design approaches to the field, in contrast to the more commonly preferred styles.

Keywords: cultural design traditions, ornamental design, organic forms from nature, textile design

Procedia PDF Downloads 211

Authors: M. Akhondizadeh, Mohsen Khajoei, Mojtaba Khajoei

Abstract:

The purpose of the present work was the design of a towing machine which was decided to be manufactured by Arman Gohar-e-Sirjan company in the Gol-e-Gohar iron ore complex in Iran. The load analysis has been conducted to determine the static and dynamic loads at the critical conditions. The inertial forces due to the velocity increment and road bump have been considered in load evaluation. The form of loading of the present machine is hauling and/or conveying the mineral machines on the mini ramp. Several stages of these forms of loading, from the initial touch of the tow and carried machine to the final position, have been assessed to determine the critical state. The stress analysis has been performed by the ANSYS software. Several geometries for the main load-carrying elements have been analyzed to have the optimum design by the minimum weight of the structure. Finally, a structure with a total weight of 38 tons has been designed with a static load-carrying capacity of 80 tons by considering the 40 tons additional capacity for dynamic effects. The stress analysis for 120 tons load gives the minimum safety factor of 1.18.

Keywords: mechanical design, stress analysis, tow structure, dynamic load, static load

Procedia PDF Downloads 90

Authors: Nargiza Nuralieva

Abstract:

This meta-analysis investigates the effectiveness of mental health interventions tailored for international students in China, with a specific focus on Uzbek students and Silk Road scholarship recipients. The comprehensive literature review synthesizes existing studies, papers, and reports, evaluating the outcomes, limitations, and cultural considerations of these programs. Data selection targets mental health programs for international students, honing in on a subset analysis related to Uzbek students and Silk Road scholarship recipients. The analysis encompasses diverse outcome measures, such as reported stress levels, utilization rates of mental health services, academic performance, and more. Results reveal a consistent and statistically significant reduction in reported stress levels, emphasizing the positive impact of these interventions. Utilization rates of mental health services witness a significant increase, highlighting the accessibility and effectiveness of support. Retention rates show marked improvement, though academic performance yields mixed findings, prompting nuanced exploration. Psychological well-being, quality of life, and overall well-being exhibit substantial enhancements, aligning with the overarching goal of holistic student development. Positive outcomes are observed in increased help-seeking behavior, positive correlations with social support, and significant reductions in anxiety levels. Cultural adaptation and satisfaction with interventions both indicate positive outcomes, underscoring the effectiveness of culturally sensitive mental health support. The findings emphasize the importance of tailored mental health interventions for international students, providing novel insights into the specific needs of Uzbek students and Silk Road scholarship recipients. This research contributes to a nuanced understanding of the multifaceted impact of mental health programs on diverse student populations, offering valuable implications for the design and refinement of future interventions. As educational institutions continue to globalize, addressing the mental health needs of international students remains pivotal for fostering inclusive and supportive learning environments.

Keywords: international students, mental health interventions, cross-cultural support, silk road scholarship, meta-analysis

Procedia PDF Downloads 36

Authors: H. Nikzad, S. Yoshitomi

Abstract:

In this paper, the optimal seismic design of reinforced concrete shear wall-frame building structures was done using structural optimization. The optimal section sizes were generated through structural optimization based on linear static analysis conforming to American Concrete Institute building design code (ACI 318-14). An analytical procedure was followed to validate the accuracy of the proposed method by comparing stresses on structural members through output files of MATLAB and ETABS. In order to consider the difference of stresses in structural elements by ETABS and MATLAB, and to avoid over-stress members by ETABS, a stress constraint ratio of MATLAB to ETABS was modified and introduced for the most critical load combinations and structural members. Moreover, seismic design of the structure was done following the International Building Code (IBC 2012), American Concrete Institute Building Code (ACI 318-14) and American Society of Civil Engineering (ASCE 7-10) standards. Typical reinforcement requirements for the structural wall, beam and column were discussed and presented using ETABS structural analysis software. The placement and detailing of reinforcement of structural members were also explained and discussed. The outcomes of this study show that the modification of section sizes play a vital role in finding an optimal combination of practical section sizes. In contrast, the optimization problem with size constraints has a higher cost than that of without size constraints. Moreover, the comparison of optimization problem with that of ETABS program shown to be satisfactory and governed ACI 318-14 building design code criteria.

Keywords: structural optimization, seismic design, linear static analysis, etabs, matlab, rc shear wall-frame structures

Procedia PDF Downloads 149

Authors: Madhusudan Hamirwasia, Sarang Barbarwar, Arshleen Kaur

Abstract:

The construction of memorials began thousands of years ago and the practice is still continuing. These memorials became a symbol to honor great people and events in the history. The aim of the study was to understand the evolution of memorials from an architectural design perspective. It is also concentrated on the similarities and differences between the memorials in Europe and those in the Indian subcontinent. The study shows how the design of a memorial has seen a considerable shift from the tribal Urasgattas to the contemporary commemorative structures. While they were somber symbolic gestures in the past, they have now transformed into a socio-cultural space in urban areas. Not only the memorials were inspired by the culture but the culture too got influenced by the memorials as with progressing time, they hold the vital link to our past. The study intends to encapsulate the essence of design elements in these memorials that convey the visitors the intangible messages held by the edifice in its tangible presence.

Keywords: evolution, emotion, memorials, symbolism

Procedia PDF Downloads 126

Authors: Milan Paudel, Fook Fah Yap, Anil K. Bastola

Abstract:

The difficulties in riding small wheel bicycles and their lesser stability have been perceived for a long time. Although small wheel bicycles are designed using the similar approach and guidelines that have worked well for big wheel bicycles, the performance of the big wheelers and the smaller wheelers are markedly different. Since both the big wheelers and small wheelers have same fundamental geometry, most blame the small wheel for this discrepancy in the performance. This paper reviews existing guidelines for bicycle design, especially the front steering geometry for the bicycle, and provides a systematic and quantitative analysis of different wheel sized bicycles. A validated mathematical model has been used as a tool to assess the dynamic performance of the bicycles in term of their self-stability. The results obtained were found to corroborate the subjective perception of cyclists for small wheel bicycles. The current approach for small wheel bicycle design requires higher speed to be self-stable. However, it was found that increasing the headtube angle and selecting a proper trail could improve the dynamic performance of small wheel bicycles. A range of parameters for front steering geometry has been identified for small wheel bicycles that have comparable stability as big wheel bicycles. Interestingly, most of the identified geometries are found to be beyond the ISO recommended range and seem to counter the current approach of small wheel bicycle design. Therefore, it was successfully shown that the guidelines for big wheelers do not translate directly to small wheelers, but careful selection of the front geometry could make small wheel bicycles as stable as big wheel bicycles.

Keywords: big wheel bicycle, design approach, ISO requirements, small wheel bicycle, stability and performance

Procedia PDF Downloads 176

Authors: F. Lhafiane, A. Elbyed, M. Bouchoum

Abstract:

The design of Reverse logistics Network has attracted growing attention with the stringent pressures from both environmental awareness and business sustainability. Reverse logistical activities include return, remanufacture, disassemble and dispose of products can be quite complex to manage. In addition, demand can be difficult to predict, and decision making is one of the challenges tasks. This complexity has amplified the need to develop an integrated architecture for product return as an enterprise system. The main purpose of this paper is to design Multi agent system (MAS) architecture using the Prometheus methodology to efficiently manage reverse logistics processes. The proposed MAS architecture includes five types of agents: Gate keeping Agent, Collection Agent, Sorting Agent, Processing Agent and Disposal Agent which act respectively during the five steps of reverse logistics Network.

Keywords: reverse logistics, multi agent system, prometheus methodology

Procedia PDF Downloads 448

Authors: Rachel M. Lørum, Henrik Eriksson, Frida Smith

Abstract:

Purpose: In recent years, the use of benchmarks for the improvement of healthcare has become increasingly common. There has been an increasing interest in why improvement initiatives so often fail to eliminate the problems they aspire to solve. Benchmarking comes with its fair share of challenges and problems, such as capturing the dynamics and complexities of the care environments, among others. In this study, we demonstrate how learning-oriented, voluntary benchmarks in the complex environment of public healthcare could be designed. Findings: Our four most important findings were the following: first, important organizational learning (OL) regarding the complexity of the service and implications on how to design a benchmark for learning and improvement occurred during the process. Second, participation by a wide range of professionals and stakeholders was crucial for capturing the complexity of people and organizations and increasing the quality of the template. Third, the continuous dialogue between all organizations involved was an important tool for ongoing organizational learning throughout the process. The last important finding was the impact of the facilitator’s role through supporting progress, coordination, and dialogue. Design: We chose participatory design as the research design. Data were derived from written materials such as e-mails, protocols, observational notes, and reflection notes collected during a period of 1.5 years. Originality: Our main contributions are the identification of important strategies, initiatives, and actors to involve when designing voluntary benchmarks for learning and improvement.

Keywords: organizational learning, quality improvement, learning-oriented benchmark, healthcare, patient safety

Procedia PDF Downloads 91

Authors: Tatyana Gavrilova, Vadim Onufriev

Abstract:

Knowledge-based systems’ design requires the developer’s owning the advanced analytical skills. The efficient development of that skills within university courses needs a deep understanding of main pitfalls and drawbacks, which students usually make during their analytical work in form of visual modeling. Thus, it was necessary to hold an analysis of 5-th year students’ learning exercises within courses of 'Intelligent systems' and 'Knowledge engineering' in Saint-Petersburg Polytechnic University. The analysis shows that both lack of system thinking skills and methodological mistakes in course design cause the errors that are discussed in the paper. The conclusion contains an exploration of the issues and topics necessary and sufficient for the implementation of the improved practices in educational design for future curricula of teaching programs.

Keywords: knowledge based systems, knowledge engineering, students’ errors, visual modeling

Procedia PDF Downloads 295

Authors: Rama Shanker, Anil Kumar Sachan

Abstract:

Basic ingredients of concrete are cement, fine aggregate, coarse aggregate and water. To produce a concrete of certain specific properties, optimum proportion of these ingredients are mixed. The important factors which govern the mix design are grade of concrete, type of cement and size, shape and grading of aggregates. Concrete mix design method is based on experimentally evolved empirical relationship between the factors in the choice of mix design. Basic draw backs of this method are that it does not produce desired strength, calculations are cumbersome and a number of tables are to be referred for arriving at trial mix proportion moreover, the variation in attainment of desired strength is uncertain below the target strength and may even fail. To solve this problem, a lot of cubes of standard grades were prepared and attained 28 days strength determined for different combination of cement, fine aggregate, coarse aggregate and water. An artificial neural network (ANN) was prepared using these data. The input of ANN were grade of concrete, type of cement, size, shape and grading of aggregates and output were proportions of various ingredients. With the help of these inputs and outputs, ANN was trained using feed forward back proportion model. Finally trained ANN was validated, it was seen that it gave the result with/ error of maximum 4 to 5%. Hence, specific type of concrete can be prepared from given material properties and proportions of these materials can be quickly evaluated using the proposed ANN.

Keywords: aggregate proportions, artificial neural network, concrete grade, concrete mix design

Procedia PDF Downloads 374

Authors: Joaquin Ticzon, Christian Demition, Jaime Honra

Abstract:

Additive manufacturing (AM) or 3D printing has been one of the emerging trends present in various industries, particularly in prototyping. This review focuses on the impact of additive manufacturing on a motor vehicle's performance aiming to investigate potential advancements to further revolutionize the way parts are manufactured. One of the most common problems faced in the automotive industry is carbon footprint emissions from motor vehicles, which was stated to be remedied by lightweight; additively manufactured parts helped reduce these emissions due to weight reduction provided by additively manufactured parts. Composed of various techniques for AM as well as materials utilized during the manufacturing process, which differ in terms of the quality and performance it provides during its application on the final product. Given this, the generative design will not be discussed in such a detailed manner because the focus will revolve around the effects on the performance of a vehicle due to additively manufactured parts.

Keywords: additive manufacturing (AM), automotive, computer aided design (CAD), generative design

Procedia PDF Downloads 7

Authors: Sowmiyaa V. S., Tiruvengala Padma, Dhanasekaran B.

Abstract:

Due to urbanization, traffic congestion, air pollution and fuel consumption underground metros are constructed in urban cities nowadays. These metros reduce the commutation time and makes the daily transportation in urban cities hassle free. To construct the underground metros deep excavations are to be carried out. These excavations should be supported by an appropriate earth retaining structures to provide stability and to prevent deformation failures. The failure of deep excavations is catastrophic and hence appropriate caution need to be carried out during design and construction stages. This paper covers the construction aspects, equipment, quality control, design aspects of one of the earth retaining systems the Diaphragm Walls.

Keywords: underground metros, diaphragm wall, quality control of diaphragm wall, design aspects of diaphragm wall

Procedia PDF Downloads 85

Authors: Muhammad M. A. S. Mahmoud

Abstract:

Natural gas sweetening process is a controlled process that must be done at maximum efficiency and with the highest quality. In this work, due to complexity and non-linearity of the process, the H₂S gas separation and the intelligent fuzzy controller, which is used to enhance the process, are simulated in MATLAB – Simulink. The new design of fuzzy control for Gas Separator is discussed in this paper. The design is based on the utilization of linear state-estimation to generate the internal knowledge-base that stores input-output pairs. The obtained input/output pairs are then used to design a feedback fuzzy controller. The proposed closed-loop fuzzy control system maintains the system asymptotically-stability while it enhances the system time response to achieve better control of the concentration of the output gas from the tower. Simulation studies are carried out to illustrate the Gas Separator system performance.

Keywords: gas separator, gas sweetening, intelligent controller, fuzzy control

Procedia PDF Downloads 448

Authors: Salem Alsanusi, Loubna Bentaher

Abstract:

Response Surface Methods (RSM) provide statistically validated predictive models that can then be manipulated for finding optimal process configurations. Variation transmitted to responses from poorly controlled process factors can be accounted for by the mathematical technique of propagation of error (POE), which facilitates ‘finding the flats’ on the surfaces generated by RSM. The dual response approach to RSM captures the standard deviation of the output as well as the average. It accounts for unknown sources of variation. Dual response plus propagation of error (POE) provides a more useful model of overall response variation. In our case, we implemented this technique in predicting compressive strength of concrete of 28 days in age. Since 28 days is quite time consuming, while it is important to ensure the quality control process. This paper investigates the potential of using design of experiments (DOE-RSM) to predict the compressive strength of concrete at 28th day. Data used for this study was carried out from experiment schemes at university of Benghazi, civil engineering department. A total of 114 sets of data were implemented. ACI mix design method was utilized for the mix design. No admixtures were used, only the main concrete mix constituents such as cement, coarse-aggregate, fine aggregate and water were utilized in all mixes. Different mix proportions of the ingredients and different water cement ratio were used. The proposed mathematical models are capable of predicting the required concrete compressive strength of concrete from early ages.

Keywords: mix proportioning, response surface methodology, compressive strength, optimal design

Procedia PDF Downloads 250

Authors: R. K. Saket

Abstract:

This paper presents design aspects and probabilistic approach for generation reliability evaluation of an alternative resource: municipal waste water based micro hydro power generation system. Annual and daily flow duration curves have been obtained for design, installation, development, scientific analysis and reliability evaluation of the MHPP. The hydro potential of the waste water flowing through sewage system of the BHU campus has been determined to produce annual flow duration and daily flow duration curves by ordering the recorded water flows from maximum to minimum values. Design pressure, the roughness of the pipe’s interior surface, method of joining, weight, ease of installation, accessibility to the sewage system, design life, maintenance, weather conditions, availability of material, related cost and likelihood of structural damage have been considered for design of a particular penstock for reliable operation of the MHPP. A MHPGS based on MWW and SEIG is designed, developed, and practically implemented to provide reliable electric energy to suitable load in the campus of the Banaras Hindu University, Varanasi, (UP), India. Generation reliability evaluation of the developed MHPP using Gaussian distribution approach, safety factor concept, peak load consideration and Simpson 1/3rd rule has presented in this paper.

Keywords: self excited induction generator, annual and daily flow duration curve, sewage system, municipal waste water, reliability evaluation, Gaussian distribution, Simpson 1/3rd rule

Procedia PDF Downloads 543

Authors: Thorsten Herrmann, Alexander Laukemann, Hansgeorg Binz, Daniel Roth

Abstract:

For the analysis of already identified and existing problems, the pertinent literature provides a comprehensive collection of approaches as well as methods in order to analyze the problems in detail. But coming up with problems, which are assets worth pursuing further, is often challenging. However, the importance of well-formulated problem ideas and their influence of subsequent creative processes are incontestable and proven. In order to meet the covered challenges, the Institute for Engineering Design and Industrial Design (IKTD) developed the Emoji Method. This paper presents the Emoji Method, which support designers to generate problem ideas in a structured way. Considering research findings from knowledge management and innovation management, research into emojis and emoticons reveal insights by means of identifying and formulating problem ideas within the early design phase. The simple application and the huge supporting potential of the Emoji Method within the early design phase are only few of the many successful results of the conducted evaluation. The Emoji Method encourages designers to identify problem ideas and describe them in a structured way in order to start focused with generating solution ideas for the revealed problem ideas.

Keywords: emojis, problem ideas, innovation management, knowledge management

Procedia PDF Downloads 132

Authors: Ibrahim Aydogdu, Alper Akin

Abstract:

In this study, the development of minimizing the cost and the CO2 emission of the RC retaining wall design has been performed by Biogeography Based Optimization (BBO) algorithm. This has been achieved by developing computer programs utilizing BBO algorithm which minimize the cost and the CO2 emission of the RC retaining walls. Objective functions of the optimization problem are defined as the minimized cost, the CO2 emission and weighted aggregate of the cost and the CO2 functions of the RC retaining walls. In the formulation of the optimum design problem, the height and thickness of the stem, the length of the toe projection, the thickness of the stem at base level, the length and thickness of the base, the depth and thickness of the key, the distance from the toe to the key, the number and diameter of the reinforcement bars are treated as design variables. In the formulation of the optimization problem, flexural and shear strength constraints and minimum/maximum limitations for the reinforcement bar areas are derived from American Concrete Institute (ACI 318-14) design code. Moreover, the development length conditions for suitable detailing of reinforcement are treated as a constraint. The obtained optimum designs must satisfy the factor of safety for failure modes (overturning, sliding and bearing), strength, serviceability and other required limitations to attain practically acceptable shapes. To demonstrate the efficiency and robustness of the presented BBO algorithm, the optimum design example for retaining walls is presented and the results are compared to the previously obtained results available in the literature.

Keywords: bio geography, meta-heuristic search, optimization, retaining wall

Procedia PDF Downloads 382

Authors: Hoi Nga Ng, Kam Weng Boey, Chi Wai Kwan

Abstract:

Supporters of Inclusive education proclaim that all students, regardless of disabilities or special educational needs (SEN), have the right to study in the normal school setting. It is asserted that students with SEN would benefit in academic performance and psychosocial adjustment via participation in common learning activities within the ordinary school system. When more and more students of SEN completed their early schooling, institute of higher education become the setting where students of SEN continue their learning. This study aimed to investigate the school well-being, social relationship, and academic self-concept of students of SEN in higher education. The Perception of Inclusion Questionnaire (PIQ) was used as the measuring instruments. PIQ was validated and incorporated in a questionnaire designed for online survey. Participation was voluntary and anonymous. A total of 90 students with SEN and 457 students without SEN responded to the online survey. Results showed no significant differences in school well-being and social relationship between students with and without SEN, but students with SEN, particularly those with learning and development impairment and those with mental illness and emotional problems, were significantly poorer in academic self-concept. Implications of the findings were discussed.

Keywords: ccademic self-concept, school well-being, social relationship, special educational needs

Procedia PDF Downloads 156

Authors: Ruth Nalugya, Claire Nimusiima, Elizabeth Kawesa, Harriet Nambejja, Geert van Hove, Janet Seeley, Femke Bannink Mbazzi

Abstract:

Background: ‘Obuntu bulamu’, an intervention for children, parents, and teachers to improve the participation and inclusion of children with disabilities (CwD) through peer-to-peer support, was developed and tested in central Uganda between 2017 and 2019. The intervention consisted of children, parents, and teachers' training sessions and peer to peer support activities directed at disability inclusion using an African disability framework. In this paper, we discuss parent participation in and parent evaluation of the ‘Obuntu bulamu’ intervention. Methods: This qualitative Afrocentric intervention study was implemented in 10 communities in the Wakiso district in Central Uganda. We purposely selected children aged 8 to 14 years with different impairments, their peers, and parents, with different levels of household income and familial support, who were enrolled in primary schools in the ten communities with on average three children with disabilities per community. Sixty four parents (33 parents of CwDs and 31 peers) participating in the ‘Obuntu bulamu’ study were interviewed at baseline and endline. Two focus group discussions were held with parents at the midline. Parents also participated in a consultative meeting about the intervention design at baseline, and two evaluation workshops held at midline and endline. Thematic data analysis of the interview and focus group data was conducted. Results: Findings showed parents found the group-based activities inspiring and said they built hope and confidence. Parents felt the intervention was acceptable, culturally appropriate, and supportive as it built on values and practices from their own traditions. Parents reported the intervention enhanced a sense of togetherness and belonging through the group meetings and follow-up activities. Parents also mentioned that the training helped them develop more positive attitudes towards CwD and disability inclusion. Parents felt that the invention increased a child’s participation and inclusion at home, school, and in communities. Conclusion: The Obuntu bulamu peer to peer support intervention is an acceptable, culturally appropriate intervention that has the potential to improve the inclusion of CwD. A larger randomized control trial is needed to evaluate the impact of the intervention model.

Keywords: inclusion, participation, inclusive education, peer support, belonging, Ubuntu, ‘Obuntu bulamu’

Procedia PDF Downloads 87

Authors: J. García-Pérez

Abstract:

An approach to compute optimum seismic design parameters is presented. It is based on the optimization of the expected present value of the total cost, which includes the initial cost of structures as well as the cost due to earthquakes. Different types of seismicity models are considered, including one for characteristic earthquakes. Uncertainties are included in some variables to observe the influence on optimum values. Optimum seismic design coefficients are computed for three different structural types representing high, medium and low rise buildings, located near and far from the seismic sources. Ordinary and important structures are considered in the analysis. The results of optimum values show an important influence of seismicity models as well as of uncertainties on the variables.

Keywords: importance factors, optimum parameters, seismic losses, seismic risk, total cost

Procedia PDF Downloads 271

Authors: Sumitra Nuanmeesri

Abstract:

The research focus on study, analyze and design the model of the infrastructure and computer networks for distance education, online learning via new media, e-learning and blended learning. The collected information from study and analyze process that information was evaluated by the index of item objective congruence (IOC) by 9 specialists to design model. The results of evaluate the model with the mean and standard deviation by the sample of 9 specialists value is 3.85. The results showed that the infrastructure and computer networks are designed to be appropriate to a great extent appropriate to a great extent.

Keywords: blended learning, new media, infrastructure and computer network, tele-education, online learning

Procedia PDF Downloads 388

Authors: Manjari Rai

Abstract:

Urbanization is an inevitable process of development of human society and an outcome of economic development and scientific and technological progress. While urbanization process in promoting the development of human civilization, also no doubt, urban landscape has been a corresponding impact. Urban environment has suffered unprecedented damage majorly due to the increase in urban population density and heavy migration rate, traffic congestion, and environmental pollution. All this have however led to a major ecological degradation and imbalance. As lands are used for the rapid and unplanned urbanization, the green lands are diminished, and severe pollution is created by waste products. Plastic, the most alarming waste at landfill sites, is yet uncontrolled. Therefore, initiatives must be taken to reduce plastic mediated pollution and increase green application. However, increasing green land is not possible due to the landfill by urban structures. In order to create a harmonious environment, sustainable development in the urban landscape becomes a matter of prime focus. This paper thus discusses the concept of ecological design combined with the urban landscape design, green landscape design on urban structures and sustainable development through the use of recyclable waste materials which is also a low costing approach of urban landscape design.

Keywords: ecological, degradation sustainable, landscape, urban

Procedia PDF Downloads 398

Authors: Agni Stylianou-Georgiou, Eliza Pitri

Abstract:

This study is a design narrative that discusses researchers’ new learning based on changes made in pedagogies and learning opportunities in the context of a Cognitive Psychology and an Art History undergraduate course. The purpose of this study was to investigate how to encourage creative problem-based play in tertiary education engaging instructors and student-teachers in designing educational games. Course instructors modified content to encourage flexible thinking during game design problem-solving. Qualitative analyses of data sources indicated that Thinking Birds’ questions could encourage flexible thinking as instructors engaged in creative problem-based play. However, student-teachers demonstrated weakness in adopting flexible thinking during game design problem solving. Further studies of student-teachers’ shifting perspectives during different instructional design tasks would provide insights for developing the Thinking Birds’ questions as tools for creative problem solving.

Keywords: creative problem-based play, educational games, flexible thinking, tertiary education

Procedia PDF Downloads 279

Authors: Z. Soleymani, M. Amirzadeh

Abstract:

Quality Function Deployment (QFD) was developed in 1960 in Japan and introduced in 1983 in America and Europe. The paper presents a real application of this technique in a way that the method of applying QFD in design and production aero fuel pumps has been considered. While designing a product and in order to apply system engineering process, the first step is identification customer needs then its transition to engineering parameters. Since each change in deign after production process leads to extra human costs and also increase in products quality risk, QFD can make benefits in sale by meeting customer expectations. Since the needs identified as well, the use of QFD tool can lead to increase in communications and less deviation in design and production phases, finally it leads to produce the products with defined technical attributes.

Keywords: customer voice, engineering parameters, gear pump, QFD

Procedia PDF Downloads 235

Authors: Helio Arthur Reis Irigaray, Fabricio Stocker

Abstract:

This study aims to discover the extent to which affinity groups effectively act to combat inequalities, promote diversity, and contribute to the inclusion of non-hegemonic groups in the work environment. To this end, we have built empirical research, in which we interviewed 36 leaders and members of the collectives of non-hegemonic groups, namely women, blacks, and LGBTQ. With the proper authorization of the participants, their interviews were transcribed and submitted for critical analysis of the discourse. The field revealed that collectives are the result of the articulation of non-hegemonic groups, which create and participate in legitimate and institutional spaces to promote diversity. We also identified that diversity actions have happened as a market trend and reproduced mimetically. As the largest companies implement these actions, they become benchmarking and thus create a flow that is reproduced by other companies. However, there is no effective change in the structures that could promote inclusion and belonging. We state that a diverse group of employees are not enough to claim that the organization is diverse and inclusive. There remains much more to discuss and delve into deeply, including gender, diversity, and intersectionality.

Keywords: diversity, inclusion, collectives, affinity groups, employee resource groups

Procedia PDF Downloads 74

Authors: Zhang Tianci, Ding Meng, Zuo Hongfu, Zeng Lina, Sun Zejun

Abstract:

Automation of airport operations can greatly improve ground movement efficiency. In this paper, we study the speed profile design problem for advanced airport ground movement control and guidance. The problem is constrained by the surface four-dimensional trajectory generated in taxi planning. A decomposed approach of two stages is presented to solve this problem efficiently. In the first stage, speeds are allocated at control points which ensure smooth speed profiles can be found later. In the second stage, detailed speed profiles of each taxi interval are generated according to the allocated control point speeds with the objective of minimizing the overall fuel consumption. We present a swarm intelligence based algorithm for the first-stage problem and a discrete variable driven enumeration method for the second-stage problem since it only has a small set of discrete variables. Experimental results demonstrate the presented methodology performs well on real world speed profile design problems.

Keywords: airport ground movement, fuel consumption, particle swarm optimization, smoothness, speed profile design

Procedia PDF Downloads 568

Authors: Axel Thallemer, Martin Danzer, Dominik Diensthuber, Aleksandar Kostadinov, Bernhard Rogler

Abstract:

Nature has always inspired the creative mind, to a lesser or greater extent. Introduced around the 1950s, Biomimetics served as a systematic method to treat the natural world as a ‘pattern book’ for technical solutions with the aim to create innovative products. Unfortunately, this technique is prone to failure when performed as a mere reverse engineering of a natural system or appearance. Contrary to that, a solution which looks at the principles of a natural design, promises a better outcome. One such example is the here presented case study, which shows the design process of three distinctive grippers. The devices have biomimetic properties on two levels. Firstly, they use a kinematic chain found in beaks and secondly, they have a biomimetic structural geometry, which was realized using additive manufacturing. In a next step, the manufacturing method was evaluated to estimate its efficiency for commercial production. The results show that the fabrication procedure is still in its early stage and thus it is not able to guarantee satisfactory results. To summarize the study, we claim that a novel solution can be derived using principles from nature, however, for the solution to be actualized successfully, there are parameters which are beyond reach for designers. Nonetheless, industrial designers can contribute to product innovation using biomimetics.

Keywords: biomimetics, innovation, design process, additive manufacturing

Procedia PDF Downloads 179

Authors: Azmi Ilmi Aziz, Wisnu Sadasih, Rizal Fanany

Abstract:

Purpose: This study describes systemic factors, intraocular lens (IOL), and ocular abnormalities in patients with IOL glistening at a tertiary hospital in Semarang. Methods: A retrospective, with a descriptive approach on patients with IOL glistening who visited the eye clinic between August 2019 to June 2023. Results: Twenty-five patients were examined; 11 patients (44%) had IOL glistening in their right eye, 4 patients (16%) in their left eye, and 10 patients (40%) in both eyes. The gender of patients consisted of 12 male patients (48%) and 13 female patients (52%). The median age of the patients was 68 years. The mean onset was 4.44 years after the first cataract surgery. Hypertension was found in 13 patients (52%), and diabetes was found in 9 patients (36%). Nine patients (36%) were identified with a foldable IOL with a closed loop design, and 1 patient (4%) with a PMMA IOL with an iris-fixated IOL design, while 15 other patients’ IOL were unrecorded. Glaucoma was found in 3 patients (12%). Conclusions: The result of this study showed that more than half of the patients were hypertensive, and some were glaucomatous, which had been discussed relevant in previous studies. Most IOL that could be identified was foldable IOL with a closed loop design. To our knowledge, the design of an IOL to glistening had never been explored. A longer study involving larger subjects is needed to better describe the systemic factors, IOL, and ocular abnormalities in patients with IOL glistening.

Keywords: glistening, intraocular lens, foldable IOL, PMMA IOL

Procedia PDF Downloads 62