Search results for: incivility at work

Authors: Wenhao Li, Shijun Guo

Abstract:

Carbon fibre reinforced composites are progressively replacing metal structures in modern civil aircraft. This is because composite materials have large potential of weight saving compared with metal. However, the achievement to date of weight saving in composite structure is far less than the theoretical potential due to many uncertainties in structural integrity and safety concern. Unlike the conventional metallic structure, composite components are bonded together along the joints where structural integrity is a major concern. To ensure the safety, metal fasteners are used to reinforce the composite bonded joints. One of the solutions for a significant weight saving of composite structure is to develop an effective technology of on-board Structural Health Monitoring (SHM) System. By monitoring the real-life stress status of composite structures during service, the safety margin set in the structure design can be reduced with confidence. It provides a means of safeguard to minimize the need for programmed inspections and allow for maintenance to be need-driven, rather than usage-driven. The aim of this paper is to develop smart composite joint. The key technology is a multifunctional thermoplastic composite fastener (MTCF). The MTCF will replace some of the existing metallic fasteners in the most concerned locations distributed over the aircraft composite structures to reinforce the joints and form an on-board SHM network system. Each of the MTCFs will work as a unit of the AU and AE technology. The proposed MTCF technology has been patented and developed by Prof. Guo in Cranfield University, UK in the past a few years. The manufactured MTCF has been successfully employed in the composite SLJ (Single-Lap Joint). In terms of the structure integrity, the hybrid SLJ reinforced by MTCF achieves 19.1% improvement in the ultimate failure strength in comparison to the bonded SLJ. By increasing the diameter or rearranging the lay-up sequence of MTCF, the hybrid SLJ reinforced by MTCF is able to achieve the equivalent ultimate strength as that reinforced by titanium fastener. The predicted ultimate strength in simulation is in good agreement with the test results. In terms of the structural health monitoring, a signal from the MTCF was measured well before the load of mechanical failure. This signal provides a warning of initial crack in the joint which could not be detected by the strain gauge until the final failure.

Keywords: composite single-lap joint, crack propagation, multifunctional composite fastener, structural health monitoring

Procedia PDF Downloads 148

Authors: Biljana Marković

Abstract:

Social networks are an integral part of our everyday lives, becoming an indispensable medium for communication in personal and business environments. New forms and ways of communication change the general mindset and significantly affect the quality of life of individuals. Quality of life is perceived as an abstract term, but often people are not aware that they directly affect the quality of their own lives, making minor but significant everyday choices and decisions. Quality of life can be defined broadly, but in the widest sense, it involves a subjective sense of satisfaction with one's life. Scientific knowledge about the impact of social networks on self-assessment of the quality of life of individuals is only just beginning to be researched. Available research indicates potential benefits as well as a number of disadvantages. In the context of the previous claims, the focus of the study conducted by the authors of this paper focuses on analyzing the impact of social networks on individual’s self-assessment of quality of life and the correlation between time spent on social networks, and the choice of content that individuals choose to share to present themselves. Moreover, it is aimed to explain how much and in what ways they critically judge the lives of others online. The research aspires to show the positive as well as negative aspects that social networks, primarily Facebook and Instagram, have on creating a picture of individuals and how they compare themselves with others. The topic of this paper is based on quantitative research conducted on a representative sample. An analysis of the results of the survey conducted online has elaborated a hypothesis which claims that content shared by individuals on social networks influences the image they create about themselves. A comparative analysis of the results obtained with the results of similar research has led to the conclusion about the synergistic influence of social networks on the feeling of the quality of life of respondents. The originality of this work is reflected in the approach of conducting research by examining attitudes about an individual's life satisfaction, the way he or she creates a picture of himself/herself through social networks, the extent to which he/she compares herself/himself with others, and what social media applications he/she uses. At the cognitive level, scientific contributions were made through the development of information concepts on quality of life, and at the methodological level through the development of an original methodology for qualitative alignment of respondents' attitudes using statistical analysis. Furthermore, at the practical level through the application of concepts in assessing the creation of self-image and the image of others through social networks.

Keywords: quality of life, social media, self image, influence of social media

Procedia PDF Downloads 108

Authors: Jeff Moussodji, Dominique Drouin

Abstract:

The highly complex technology requirements of today’s integrated circuits (ICs), lead to the increased use of several materials types such as metal structures, brittle and porous low-k materials which are used in both front end of line (FEOL) and back end of line (BEOL) process for wafer manufacturing. In order to singulate chip from wafer, a critical laser-grooving process, prior to blade dicing, is used to remove these layers of materials out of the dicing street. The combination of laser-grooving and blade dicing allows to reduce the potential risk of induced mechanical defects such micro-cracks, chipping, on the wafer top surface where circuitry is located. It seems, therefore, essential to have a fundamental understanding of the physics involving laser-dicing in order to maximize control of these critical process and reduce their undesirable effects on process efficiency, quality, and reliability. In this paper, the study was based on the convergence of two approaches, numerical and experimental studies which allowed us to investigate the interaction of a nanosecond pulsed laser and BEOL wafer materials. To evaluate this interaction, several laser grooved samples were compared with finite element modeling, in which three different aspects; phase change, thermo-mechanical and optic sensitive parameters were considered. The mathematical model makes it possible to highlight a groove profile (depth, width, etc.) of a single pulse or multi-pulses on BEOL wafer material. Moreover, the heat affected zone, and thermo-mechanical stress can be also predicted as a function of laser operating parameters (power, frequency, spot size, defocus, speed, etc.). After modeling validation and calibration, a satisfying correlation between experiment and modeling, results have been observed in terms of groove depth, width and heat affected zone. The study proposed in this work is a first step toward implementing a quick assessment tool for design and debug of multiple laser grooving conditions with limited experiments on hardware in industrial application. More correlations and validation tests are in progress and will be included in the full paper.

Keywords: laser-dicing, nano-second pulsed laser, wafer multi-stack, multiphysics modeling

Procedia PDF Downloads 189

Authors: Bharathadas Sandhya

Abstract:

Janamaithri Suraksha Project is the community policing project of Kerala police, fully sponsored by the Government of Kerala and in vogue in Kerala for the last ten years. The socio-economically weaker areas in the hilly terrains consisting of tribal hamlets are given special importance under the project. These hamlets are visited by the beat police officers, and they intervene in various issues in the hamlets. This study is based on data collected from 350 respondents living in the tribal hamlets of the Nilambur area in the District of Malappuram. The respondents were personally interviewed by the research team using a questionnaire consisting of 183 questions, seeking the details regarding their interaction with beat police officers, their ability to prevent or detect crimes, the menace of Maoists (extremist) presence, their interventions in other socio-economic problems like alcoholism, school dropout issues, lack of facilities for preparation for competitive examinations for educated youth, etc. The perception of the tribal population regarding the effectiveness of police intervention in their criminal justice complaints, the attitude of the police officers towards the tribal population when they approach the police station with a criminal complaint, are also studied. The general socio-economic problems of the tribal population as perceived by them are also brought out. Being the visible agency of the government, the police person coming on beat duty to the hamlet is generally seen by the tribal population as a representative to whom they can communicate the issues, even if it’s solution rests with another department like the forest or agriculture. The analysis of the primary data is carried out using computer applications. The amount of social justice benefits the tribal hamlets received through various government schemes, and their deficiencies are brought out in the study. From the conclusions of the study, certain suggestions for positive criminal justice and social justice intervention strategies are made out. The need for various government departments to work in tandem with each other so as to bring out more effectiveness in the socio-economic projects is evident from the study. Whether it is the need to obtain a transport to go to school or problem of drinking water or even opening a bank account, at least occasionally, the visiting beat police officer is of help to the tribal population. Mostly the tribal population feels free to approach the police with a criminal complaint without any inhibitions.

Keywords: community policing, beat police officer, criminal justice, social justice

Procedia PDF Downloads 132

Authors: Iva Blazkova, Amitava Moulick, Vedran Milosavljevic, Pavel Kopel, Marketa Vaculovicova, Vojtech Adam, Rene Kizek

Abstract:

Doxorubicin is one of the most commonly used and the most effective chemotherapeutic drugs. This antracycline drug isolated from the bacteria Streptomyces peuceticus var. caesius is sold under the trade name Adriamycin (hydroxydaunomycin, hydroxydaunorubicin). Doxorubicin is used in single therapy to treat hematological malignancies (blood cancers, leukaemia, lymphoma), many types of carcinoma (solid tumors) and soft tissue sarcomas. It has many serious side effects like nausea and vomiting, hair lost, myelosupression, oral mucositis, skin reactions and redness, but the most serious one is the cardiotoxicity. Because of the risk of heart attack and congestive heart failure, the total dose administered to patients has to be accurately monitored. With the aim to lower the side effects and to targeted delivery of doxorubicin into the tumor tissue, the different nanoparticles are studied. The drug can be bound on a surface of nanoparticle, encapsulated in the inner cavity, or incorporated into the structure of nanoparticle. Among others, carbon nanoparticles (graphene, carbon nanotubes, fullerenes) are highly studied. Besides the number of inorganic nanoparticles, a great potential exhibit also organic ones mainly lipid-based and polymeric nanoparticle. The aim of this work was to perform a toxicity study of free doxorubicin compared to doxorubicin conjugated with various nanotransporters. The effect of liposomes, fullerenes, graphene, and carbon nanotubes on the toxicity was analyzed. As a first step, the binding efficacy of between doxorubicin and the nanotransporter was determined. The highest efficacy was detected in case of liposomes (85% of applied drug was encapsulated) followed by graphene, carbon nanotubes and fullerenes. For the toxicological studies, the chicken embryos incubated under controlled conditions (37.5 °C, 45% rH, rotation every 2 hours) were used. In 7th developmental day of chicken embryos doxorubicin or doxorubicin-nanotransporter complex was applied on the chorioallantoic membrane of the eggs and the viability was analyzed every day till the 17th developmental day. Then the embryos were extracted from the shell and the distribution of doxorubicin in the body was analyzed by measurement of organs extracts using laser induce fluorescence detection. The chicken embryo mortality caused by free doxorubicin (30%) was significantly lowered by using the conjugation with nanomaterials. The highest accumulation of doxorubicin and doxorubicin nanotransporter complexes was observed in the liver tissue

Keywords: doxorubicin, chicken embryos, nanotransporters, toxicity

Procedia PDF Downloads 434

Authors: Alexander E. Hramov, Vadim V. Grubov, Alexey A. Koronovskii, Maria K. Kurovskaуa, Anastasija E. Runnova

Abstract:

The perception of visual signals in the brain was among the first issues discussed in terms of multistability which has been introduced to provide mechanisms for information processing in biological neural systems. In this work the influence of the cognitive noise on the visual perception of multistable pictures has been investigated. The study includes an experiment with the bistable Necker cube illusion and the theoretical background explaining the obtained experimental results. In our experiments Necker cubes with different wireframe contrast were demonstrated repeatedly to different people and the probability of the choice of one of the cubes projection was calculated for each picture. The Necker cube was placed at the middle of a computer screen as black lines on a white background. The contrast of the three middle lines centered in the left middle corner was used as one of the control parameter. Between two successive demonstrations of Necker cubes another picture was shown to distract attention and to make a perception of next Necker cube more independent from the previous one. Eleven subjects, male and female, of the ages 20 through 45 were studied. The choice of the Necker cube projection was detected with the Electroencephalograph-recorder Encephalan-EEGR-19/26, Medicom MTD. To treat the experimental results we carried out theoretical consideration using the simplest double-well potential model with the presence of noise that led to the Fokker-Planck equation for the probability density of the stochastic process. At the first time an analytical solution for the probability of the selection of one of the Necker cube projection for different values of wireframe contrast have been obtained. Furthermore, having used the results of the experimental measurements with the help of the method of least squares we have calculated the value of the parameter corresponding to the cognitive noise of the person being studied. The range of cognitive noise parameter values for studied subjects turned to be [0.08; 0.55]. It should be noted, that experimental results have a good reproducibility, the same person being studied repeatedly another day produces very similar data with very close levels of cognitive noise. We found an excellent agreement between analytically deduced probability and the results obtained in the experiment. A good qualitative agreement between theoretical and experimental results indicates that even such a simple model allows simulating brain cognitive dynamics and estimating important cognitive characteristic of the brain, such as brain noise.

Keywords: bistability, brain, noise, perception, stochastic processes

Procedia PDF Downloads 430

Authors: A. Shaygani, R. Saifi, M. S. Saidi, M. Sani

Abstract:

Particle size distribution, the most important characteristics of aerosols, is obtained through electrical characterization techniques. The dynamics of charged nano-particles under the influence of electric field in electrical mobility spectrometer (EMS) reveals the size distribution of these particles. The accuracy of this measurement is influenced by flow conditions, geometry, electric field and particle charging process, therefore by the transfer function (transfer matrix) of the instrument. In this work, a wire-cylinder corona charger was designed and the combined field-diffusion charging process of injected poly-disperse aerosol particles was numerically simulated as a prerequisite for the study of a multi-channel EMS. The result, a cloud of particles with non-uniform charge distribution, was introduced to the EMS. The flow pattern and electric field in the EMS were simulated using computational fluid dynamics (CFD) to obtain particle trajectories in the device and therefore to calculate the reported signal by each electrometer. According to the output signals (resulted from bombardment of particles and transferring their charges as currents), we proposed a modification to the size of detecting rings (which are connected to electrometers) in order to evaluate particle size distributions more accurately. Based on the capability of the system to transfer information contents about size distribution of the injected particles, we proposed a benchmark for the assessment of optimality of the design. This method applies the concept of Von Neumann entropy and borrows the definition of entropy from information theory (Shannon entropy) to measure optimality. Entropy, according to the Shannon entropy, is the ''average amount of information contained in an event, sample or character extracted from a data stream''. Evaluating the responses (signals) which were obtained via various configurations of detecting rings, the best configuration which gave the best predictions about the size distributions of injected particles, was the modified configuration. It was also the one that had the maximum amount of entropy. A reasonable consistency was also observed between the accuracy of the predictions and the entropy content of each configuration. In this method, entropy is extracted from the transfer matrix of the instrument for each configuration. Ultimately, various clouds of particles were introduced to the simulations and predicted size distributions were compared to the exact size distributions.

Keywords: aerosol nano-particle, CFD, electrical mobility spectrometer, von neumann entropy

Procedia PDF Downloads 317

Authors: Cynthia Briggs, Kimberly Gerardi

Abstract:

Over the past six years, the authors have been working together on World Language Collaborations in the Middle School French Program at St. Luke's School in New Canaan, Connecticut, USA. Author 2 brings design expertise to the projects, and both teachers have utilized the fabrication lab, emerging technologies, and collaboration with students. Each year, author 1 proposes a project scope, and her students are challenged to design and engineer a signature project. Both partners have improved the iterative process to ensure deeper learning and sustained student inquiry. The projects range from a 1:32 scale model of the Eiffel Tower that was CNC routed to a fully functional jukebox that plays francophone music, lights up, and can hold up to one thousand songs powered by Raspberry Pi. The most recent project is a Fragrance Marketplace, culminating with a pop-up store for the entire community to discover. Each student will learn the history of fragrance and the chemistry behind making essential oils. Students then create a unique brand, marketing strategy, and concept for their signature fragrance. They are further tasked to use the industrial design process (bottling, packaging, and creating a brand name) to finalize their product for the public Marketplace. Sometimes, these dynamic projects require maintenance and updates. For example, our wall-mounted, three-foot francophone clock is constantly changing. The most recent iteration uses Chat GPT to program the Arduino to reconcile the real-time clock shield and keep perfect time as each hour passes. The lights, motors, and sounds from the clock are authentic to each region, represented with laser-cut embellishments. Inspired by Michel Parmigiani, the history of Swiss watch-making, and the precision of time instruments, we aim for perfection with each passing minute. The authors aim to share exemplary work that is possible with students of all ages. We implemented the reverse engineering process to focus on student outcomes to refine our collaborative process. The products that our students create are prime examples of how the design engineering process is applicable across disciplines. The authors firmly believe that the past and present of World cultures inspire innovation.

Keywords: collaboration, design thinking, emerging technologies, world language

Procedia PDF Downloads 26

Authors: Henrique Rangel, Alexandre Fadel, Igor De Lazari, Bianca Neri, Carlos Bolonha

Abstract:

This paper promotes a comparative analysis of American and Brazilian models of federalism assuming their levels of political centralization as main criterion. The central problem faced herein is the Brazilian approach of Unitarian regime. Although the hegemony of federative form after 1989, Brazil had a historical frame of political centralization that remains under the 1988 constitutional regime. Meanwhile, United States framed a federalism in which States absorb significant authorities. The hypothesis holds that the amount of alternative criteria of federalization – which can generate political centralization –, and the way they are upheld on judicial review, are crucial to understand the levels of political centralization achieved in each model. To test this hypothesis, the research is conducted by a methodology temporally delimited to 1994-2014 period. Three paradigmatic precedents of U.S. Supreme Court were selected: United States vs. Morrison (2000), on gender-motivated violence, Gonzales vs. Raich (2005), on medical use of marijuana, and United States vs. Lopez (1995), on firearm possession on scholar zones. These most relevant cases over federalism in the recent activity of Supreme Court indicates a determinant parameter of deliberation: the commerce clause. After observe the criterion used to permit or prohibit the political centralization in America, the Brazilian normative context is presented. In this sense, it is possible to identify the eventual legal treatment these controversies could receive in this Country. The decision-making reveals some deliberative parameters, which characterizes each federative model. At the end of research, the precedents of Rehnquist Court promote a broad revival of federalism debate, establishing the commerce clause as a secure criterion to uphold or not the necessity of centralization – even with decisions considered conservative. Otherwise, the Brazilian federalism solves them controversies upon in a formalist fashion, within numerous and comprehensive – sometimes casuistic too – normative devices, oriented to make an intense centralization. The aim of this work is indicate how jurisdictional federalism found in United States can preserve a consistent model with States robustly autonomous, while Brazil gives preference to normative mechanisms designed to starts from centralization.

Keywords: constitutional design, federalism, U.S. Supreme Court, legislative authority

Procedia PDF Downloads 501

Authors: Himali Gunasekara, Baddika Jayaratne

Abstract:

Haematological abnormalities are known to cause Ischemic Stroke or Transient Ischemic Attack (TIA). The identification of haematological correlates plays an important role in a management and secondary prevention. The objective of this study was to describe haematological correlates of stroke and their association between stroke profile. The haematological correlates screened were Lupus Anticoagulant, Dysfibroginemia, Paroxysmal nocturnal haemoglobinurea (PNH), Sickle cell disease, Systemic Lupus Erythematosis (SLE) and Myeloploriferative Neoplasms (MPN). A cross sectional descriptive study was conducted in a sample of 152 stroke patients referred to haematology department of National Hospital of Sri Lanka for thrombophilia screening. Different tests were performed to assess each hematological correlate. Diluted Russels Viper Venom Test and Kaolin clotting time were done to assess Lupus anticoagulant. Full blood count (FBC), blood picture, Sickling test and High Performance Liquid Chromatography were the tests used for detection of Sickle cell disease. Paroxysmal nocturnal haemoglobinurea was assessed by FBC, blood picture, Ham test and Flowcytometry. FBC, blood picture, Janus Kinase 2 (V617F) mutation analysis, erythropoietin level and bone marrow examination were done to look for the Myeloproliferative neoplasms. Dysfibrinogenaemia was assessed by TT, fibrinogen antigen test, clot observation and clauss test. Anti nuclear antibody test was done to look for systemic lupus erythematosis. Among study sample, 134 patients had strokes and only 18 had TIA. The recurrence of stroke/TIA was observed in 13.2% of patients. The majority of patients (94.7%) have had radiological evidence of thrombotic event. One fourth of patients had past thrombotic events while 12.5% had family history of thrombosis. Out of haematological correlates screened, Lupus anticoagulant was the commonest haematological correlate (n=16 ) and dysfibrigonaemia(n=11 ) had the next high prevalence. One patient was diagnosed with Essential thrombocythaemia and one with SLE. None of the patients were positive for screening tests done for sickle cell disease and PNH. The Haematological correlates were identified in 19% of our study sample. Among stroke profile only presence of past thrombotic history was statistically significantly associated with haematological disorders (P= 0.04). Therefore, hematological disorders appear to be an important factor in etiological work-up of stroke patients particularly in patients with past thrombotic events.

Keywords: stroke, transient ischemic attack, hematological correlates, hematological disorders

Procedia PDF Downloads 217

Authors: Valentin Nicorescu, Nicoleta C. Predescu, Camelia Papuc, Iuliana Gajaila, Carmen D. Petcu

Abstract:

The oxidation of the fresh muscle oxymyoglobin (bright red colour) to metmyoglobin (brown colour) leads to discoloration of red meats. After slaughter, enzymatic systems involved in metmyoglobin reduction are continually depleted as time post-mortem progresses, thus the meat colour is affected. Phenolic compounds are able to scavenge reactive species involved in oxymyoglobin oxidation and to reduce metmyoglobin to oxymyoglobin. The aim of this study was to investigate the effect of polyphenols extracted from hawthorn fruits on the stability of oxymyoglobin and myofibrillar proteins in ground pork subject to refrigeration for 6 days. Hawthorn polyphenols (HP) were added in ground pork in 100, 200 and 300 ppm concentrations. Oxymyoglobin and metmyoglobin were evaluated spectrophotometrically at every 2 days and electrophoretic pattern of myofibrillar proteins was investigated at days 0 and 6 by Sodium Dodecyl Sulfate Polyacrylamide Gel Electrophoresis (SDS-PAGE). For all meat samples, oxymyoglobin concentration significantly decreased during the first 4 days of refrigeration. After 6 days, the significant decrease of oxymyoglobin concentration continued only in the negative control samples. In samples treated with HP and butylated hydroxylanisole (BHA - positive control), oxymyoglobin concentration increased after 6 days of refrigeration, the highest levels complying with the following order: 100 ppm HP > 200 ppm HP > 300 ppm HP > 100 ppm BHA. The increase in metmyoglobin was coincidental with the decrease in oxymyoglobin; metmyoglobin concentration progressively increased during the first 4 days of refrigeration in all meat samples. After 6 days, in meat samples treated with HP and BHA, lower metmyoglobin concentrations were found (compared to day 4), respecting the following order: 100 ppm HP < 200 ppm HP < 300 ppm HP < 100 ppm BHA. These results showed that hawthorn polyphenols and BHA reduced metmyoglobin (MbFe3+) to oxymyoglobin (MbFe2+), and the strongest reducing character was recorded for 100 ppm HP. After 6 days of refrigeration, electrophoretic pattern of myofibrillar proteins showed minor changes compared to day 0, indicating that HP prevent protein degradation as well as synthetic antioxidant BHA. Also, HP did not induce cross-links in the myofibrillar proteins, to form protein aggregates, and no risk of reducing their ability to retain water was identified. The pattern of oxymyoglobin and metmyoglobin concentrations determined in this study showed that hawthorn polyphenols are able to reduce metmyoglobin to oxymyoglobin and to delay oxymyoglobin oxidation, especially when they are added to ground meat in concentration of 100 ppm. This work was carried out through Partnerships in priority areas Program – PN II, implemented with the support of MEN – UEFISCDI (Romania), project nr. 149/2014.

Keywords: Hawthorn polyphenols, metmyoglobin, oxymyoglobin, proteins stability

Procedia PDF Downloads 200

Authors: Rafid Mueen, Konstantin Konstantinov, Micheal Lerch, Zhenxiang Cheng

Abstract:

In the past two decades, the concern for skin protection from ultraviolet (UV) radiation has attracted considerable attention due to the increased intensity of UV rays that can reach the Earth’s surface as a result of the breakdown of ozone layer. Recently, UVA has also attracted attention, since, in comparison to UVB, it can penetrate deeply into the skin, which can result in significant health concerns. Sunscreen agents are one of the significant tools to protect the skin from UV irradiation, and it is either organic or in organic. Developing of inorganic UV blockers is essential, which provide efficient UV protection over a wide spectrum rather than organic filters. Furthermore inorganic UV blockers are good comfort, and high safety when applied on human skin. Inorganic materials can absorb, reflect, or scatter the ultraviolet radiation, depending on their particle size, unlike the organic blockers, which absorb the UV irradiation. Nowadays, most inorganic UV-blocking filters are based on (TiO2) and ZnO). ZnO can provide protection in the UVA range. Indeed, ZnO is attractive for in sunscreen formulization, and this relates to many advantages, such as its modest refractive index (2.0), absorption of a small fraction of solar radiation in the UV range which is equal to or less than 385 nm, its high probable recombination of photogenerated carriers (electrons and holes), large direct band gap, high exciton binding energy, non-risky nature, and high tendency towards chemical and physical stability which make it transparent in the visible region with UV protective activity. A significant issue for ZnO use in sunscreens is that it can generate ROS in the presence of UV light because of its photocatalytic activity. Therefore it is essential to make a non-photocatalytic material through modification by other metals. Several efforts have been made to deactivate the photocatalytic activity of ZnO by using inorganic surface modifiers. The doping of ZnO by different metals is another way to modify its photocatalytic activity. Recently, successful doping of ZnO with different metals such as Ce, La, Co, Mn, Al, Li, Na, K, and Cr by various procedures, such as a simple and facile one pot water bath, co-precipitation, hydrothermal, solvothermal, combustion, and sol gel methods has been reported. These materials exhibit greater performance than undoped ZnO towards increasing the photocatalytic activity of ZnO in visible light. Therefore, metal doping can be an effective technique to modify the ZnO photocatalytic activity. However, in the current work, we successfully reduce the photocatalytic activity of ZnO through Na doped ZnO fabricated via sol-gel and hydrothermal methods.

Keywords: photocatalytic, ROS, UVA, ZnO

Procedia PDF Downloads 127

Authors: Abdulqader Alkhouzaam, Hazim Qiblawey, Majeda Khraisheh

Abstract:

Membrane treatment for desalination and wastewater treatment is one of the promising solutions to affordable clean water. It is a developing technology throughout the world and considered as the most effective and economical method available. However, the limitations of membranes’ mechanical and chemical properties restrict their industrial applications. Hence, developing novel membranes was the focus of most studies in the water treatment and desalination sector to find new materials that can improve the separation efficiency while reducing membrane fouling, which is the most important challenge in this field. Graphene oxide (GO) is one of the materials that have been recently investigated in the membrane water treatment sector. In this work, ultrafiltration polysulfone (PSF) membranes with high antifouling properties were synthesized by incorporating different loadings of GO. High-oxidation degree GO had been synthesized using a modified Hummers' method. The synthesized GO was characterized using different analytical techniques including elemental analysis, Fourier transform infrared spectroscopy - universal attenuated total reflectance sensor (FTIR-UATR), Raman spectroscopy, and CHNSO elemental analysis. CHNSO analysis showed a high oxidation degree of GO represented by its oxygen content (50 wt.%). Then, ultrafiltration PSF membranes incorporating GO were fabricated using the phase inversion technique. The prepared membranes were characterized using scanning electron microscopy (SEM) and atomic force microscopy (AFM) and showed a clear effect of GO on PSF physical structure and morphology. The water contact angle of the membranes was measured and showed better hydrophilicity of GO membranes compared to pure PSF caused by the hydrophilic nature of GO. Separation properties of the prepared membranes were investigated using a cross-flow membrane system. Antifouling properties were studied using bovine serum albumin (BSA) and humic acid (HA) as model foulants. It has been found that GO-based membranes exhibit higher antifouling properties compared to pure PSF. When using BSA, the flux recovery ratio (FRR %) increased from 65.4 ± 0.9 % for pure PSF to 84.0 ± 1.0 % with a loading of 0.05 wt.% GO in PSF. When using HA as model foulant, FRR increased from 87.8 ± 0.6 % to 93.1 ± 1.1 % with 0.02 wt.% of GO in PSF. The pure water permeability (PWP) decreased with loadings of GO from 181.7 L.m⁻².h⁻¹.bar⁻¹ of pure PSF to 181.1, and 157.6 L.m⁻².h⁻¹.bar⁻¹ with 0.02 and 0.05 wt.% GO respectively. It can be concluded from the obtained results that incorporating low loading of GO could enhance the antifouling properties of PSF hence improving its lifetime and reuse.

Keywords: antifouling properties, GO based membranes, hydrophilicity, polysulfone, ultrafiltration

Procedia PDF Downloads 130

Authors: Kazi Rizvan, Yamin Rekhu

Abstract:

Due to high competitiveness in industries throughout the world, every industry is trying hard to utilize all their resources to keep their productivity as high as possible. Many tools have been being used to ensure smoother flow of an operation, to balance tasks, to maintain proper schedules for tasks, to maintain proper sequence for tasks, to reduce unproductive time. All of these tools are used to augment productivity within an industry. Kanban board is one of them and of the many important tools of lean production system. Kanban Board is a visual depiction of the status of tasks. Kanban board shows the actual status of the tasks. It conveys the progress and issues of tasks as well. Using Kanban Board, tasks can be distributed among workers and operation targets can be visually represented to them. In this paper, an example of Kanban board from the aspects of Brothers Furniture Limited was taken and how the Kanban board system was implemented, how the board was designed and how it was made easily perceivable for the less literate or illiterate workers. The Kanban board was designed for the packing section of Brothers Furniture Limited. It was implemented for the purpose of representing the tasks flow to the workers and to mitigate the time that was wasted while the workers remained wondering about what task they should start after they finish one. Kanban board subsumed seven columns and there was a column for comments where if any problem occurred during working on the tasks. Kanban board was helpful for the workers as the board showed the urgency of the tasks. It was also helpful for the store section as they could understand which products and how much of them could be delivered to store at any certain time. Kanban board had all the information centralized which is why the work-flow got paced up and idle time was minimized. Regardless of many workers being illiterate or less literate, Kanban board was still explicable for the workers as the Kanban cards were colored. Since the significance of colors can be conveniently interpretable to them, colored cards helped a great deal in that matter. Hence, the illiterate or less literate workers didn’t have to spend time wondering about the significance of the cards. Even when the workers weren’t told the significance of the colored cards, they could grow a feeling about their meaning as colors can trigger anyone’s mind to perceive the situation. As a result, the board elucidated the workers about what board required them to do, when to do and what to do next. Kanban board alleviated excessive time between tasks by setting day-plan for targeted tasks and it also reduced time during tasks as the workers were acknowledged of forthcoming tasks for a day. Being very specific to the tasks, Kanban board helped the workers become more focused on their tasks helped them do their job with more perfection. As a result, The Kanban board helped achieve a 8.75% increase in productivity than the productivity before the Kanban board was implemented.

Keywords: color, Kanban Board, Lean Tool, literacy, packing, productivity

Procedia PDF Downloads 218

Authors: Vicente Espinola, Luis Torres, Christhian Gonzalez

Abstract:

Entrepreneurship is a topic of current interest in Mexico and the World, which has been fostered through public policies with great impact on its generation. The strategies used in Mexico have not been successful, being motivational strategies aimed at the masses with the intention that someone in the process generates a venture. The strategies used for its development have been "picking of winners" favoring those who have already overcome the initial stages of undertaking without effective support. This situation shows a disarticulation that appears even more in social entrepreneurship; due to this, it is relevant to research on those elements that could develop them and thus integrate a model of entrepreneurship and social innovation for Mexico. Social entrepreneurship should be generating social innovation, which is translated into business models in order to make the benefits reach the population. These models are proposed putting the social impact before the economic impact, without forgetting its sustainability in the medium and long term. In this work, we present a simple model of innovation and social entrepreneurship for Guanajuato, Mexico. This algorithm was based on how social innovation could be generated in a systemic way for Mexico through different institutions that promote innovation. In this case, the technological parks of the state of Guanajuato were studied because these are considered one of the areas of Mexico where its main objectives are to make technology transfer to companies but overlooking the social sector and entrepreneurs. An experimental design of n = 60 was carried out with potential entrepreneurs to identify their perception of the social approach that the enterprises should have, the skills they consider required to create a venture, as well as their interest in generating ventures that solve social problems. This experiment had a 2K design, the value of k = 3 and the computational simulation was performed in R statistical language. A simple model of interconnected variables is proposed, which allows us to identify where it is necessary to increase efforts for the generation of social enterprises. The 96.67% of potential entrepreneurs expressed interest in ventures that solve social problems. In the analysis of the variables interaction, it was identified that the isolated development of entrepreneurial skills would only replicate the generation of traditional ventures. The variable of social approach presented positive interactions, which may influence the generation of social entrepreneurship if this variable was strengthened and permeated in the processes of training and development of entrepreneurs. In the future, it will be necessary to analyze the institutional actors that are present in the social entrepreneurship ecosystem, in order to analyze the interaction necessary to strengt the innovation and social entrepreneurship ecosystem.

Keywords: social innovation, model, entrepreneurship, technological parks

Procedia PDF Downloads 253

Authors: M. Walmsley, S. Elmatarri, S. Mannion

Abstract:

Introduction: Self-inflicted injury is a recognised cause of major trauma in adults and is an independent indicator of a reduced functional outcome compared to non-intentional major trauma. There is little literature available on the inpatient mental health (MH) management of this vulnerable group. A retrospective review was conducted of inpatient MH management of major trauma patients admitted to a UK regional Major Trauma Centre (MTC). Their outcomes were compared to all major trauma patients. This group of patients required multiple MH interventions whilst on the Major Trauma Ward (MTW) and a had worse functional outcome compared to non-intentional trauma. Method: The national TARN (Trauma Audit and Research Network) database was used to identify patients admitted to a regional MTC over a 2-year period from June 2018 to July 2020. Patients with an ISS (Injury Severity Score) of greater than 15 with a mechanism of either self-harm or high-risk behavior were included for further analysis. Inpatient medical notes were reviewed for MH interventions on the MTW. Further outcomes, including mortality, length of stay (LOS) and Glasgow Outcome Score (GOS) were compared with all major trauma patients for the same time period. Results: A total of 60 patients were identified in the time period and of those, 27 spent time on the MTW. A total of 23 (85%) had a prior MH diagnosis, with 11 (41%) under the care of secondary MH services. Adequate inpatient records for review were available for 24 patients. During their inpatient stay, 8 (33%) were reviewed on the ward by the inpatient MH team. There were 10 interventions required for 6 (25%) patients on the MTW including, sections under the Mental Health Act, transfer to specialist MH facility, pharmacological sedation and security being called to the MTW. When compared to all major trauma patients, those admitted due to self-harm or high-risk behavior had a statistically significantly higher ISS (31.43 vs 24.22, p=0.0001) and LOS (23.51d vs 16.06d, p=0.002). Functional outcomes using the GOS were reduced in this group of patients, GOS 5 (low disability) (51.66% vs. 61.01%) and they additionally had a higher level of mortality, GOS 1 (15.00% vs 11.67%). Discussion: Intentional self-harm is a recognised cause of major trauma in adults and this patient group sustains more severe injuries, requiring a longer hospital stay with worse outcomes compared to all major trauma patients. Inpatient MH interventions are required for a significant proportion of these patients and therefore, there needs to be a close relationship with MH services. There is limited available evidence for how this patient group is best managed as an inpatient to aid their recovery and further work is needed on how outcomes in this vulnerable group can be improved.

Keywords: adult major trauma, attempted suicide, self-inflicted major trauma, inpatient management

Procedia PDF Downloads 162

Authors: Diana K. Kwok

Abstract:

Despite the fact that Hong Kong government aims to develop an inclusive society, sexual minority students continue to encounter sexual prejudice without legal protection. They also have difficulties accessing relevant services from mental health and educational professionals, who do not receive systematic training to work with sexual minority students. Informed by the literature on sexual prejudice, heterosexual hegemony, genderism, as well as code of practice for frontline practitioners, the authors explored self-perceived knowledge of teachers and sexual minorities on sexuality and sexual prejudice, and how they perceive prejudice towards sexual minorities in Chinese cultural context. Semi-structure qualitative interviews were carried out with 31 school personnel informants (school teachers and counseling team members) and 25 sexual minority informants on their understanding of sexuality knowledge, their perception of sexual prejudice within school context in Hong Kong, as well as their suggested themes on teachers training on sexual prejudice reduction. This presentation specifically focuses on transcripts from sexual minority informants. Data analysis was carried out through NVivo, and followed the procedures spelt out in the qualitative research literature. Trustworthiness of the study was addressed through various strategies. Preliminary themes emerged from transcript content analysis: 1) A gap of knowledge between sexual minority informants and teachers; 2) Perception on sexual prejudice within cultural context; 3) Heterosexual hegemony and genderism within school system; 4) Needs for mandatory training: contents and strategies. The sexual minority informants found that teachers they encountered were predominantly adopted concepts of binary sex and dichotomous gender. Informants also indicated that the teachings of Confucianism cultural values, religiosity in Hong Kong might well be important cultural forces contributing to sexual prejudice manifested in school context. Although human rights and social justice concepts were embedded in professional code of practice of teachers and school helping professionals, informants found that teachers they encountered may face a dilemma when supporting sexual minority students navigating heterosexual hegemony and genderism in, as a consequence of their personal, institutional, cultural and religious backgrounds. Acknowledgments: The sexual prejudice project was funded by the Hong Kong Research Grant Council (ECS28401614), 2015 to 2017.

Keywords: sexual prejudice, Chinese teachers, Chinese sexual minorities, teacher training

Procedia PDF Downloads 266

Authors: Masnur Marzuki

Abstract:

As in other democratic countries, the constitutional court of Indonesia has the role of interpreting and applying the Constitution in order to preserve its supremacy testing the constitutionality of statutes. With its strong power to enforce and guard the Constitution, the court is now challenged to provide people an opportunity to understand their constitutional rights close up. At the same time, the court has built up an enviable reputation among constitutional courts in new democracies for the technical quality of its legitimacy in the legal sense. Since its establishment in 2003, the Constitutional Court of Indonesia has decided more than 190 statutes in judicial review case. It has been remarkably successful to make a credible start on its work of guarding the Constitution. Unsurprisingly, many argue that the Court has elevated Indonesia’s democracy to a whole new level. In accomplishing its roles judicial review, the basic principle that can be identified is that the Constitutional Court must always be subordinated to the Constitution. It is not being allowed to invade the field of the legislator. In doing so, the court does not have any discretionary political basis in order to create legal norms or provisions that could not be deducted from the Constitution itself. When interpreting a statute “in accordance with the constitution”, the court recognizes and reasserts that it is strictly forbidden to extend the scope of a legal provision in such a way that would create a general norm not established by the law-maker. This paper aims to identify and assess the latest role of Indonesian Constitutional Court in interpreting and applying the Constitution. In particular, it questions 1) the role of the Constitutional Court in judicial review; and 2) the role of the court to assist the legislators in the accomplishment of their functions in order to preserve its supremacy testing the constitutionality of statutes. Concerning positive legislator, jurisprudential and judicial review theories will be approached. The empirical part will include qualitative and comparative research. Main questions to be addressed: Can the Constitutional Court be functionalized as positive legislator? What are the criteria for conducting role of Constitutional Courts as Positive Legislators and how can it be accepted? Concerning the subordination of Constitutional Courts to the Constitution and judicial review, both qualitative and quantitative methods will be used, and differences between Indonesia and German Constitutional Court will be observed. Other questions to be addressed: Can Constitutional Courts have any discretionary political basis in order to create legal norms or provisions that could not be deducted from the Constitution itself. Should the Constitutional Court always act as a negative legislator? However, the Constitutional Court in Indonesia has played role as positive legislators which create dynamic of Indonesian legal development. In performing the task of reviewing the constitutionality of statutes, the Constitutional Court has created legal norms or provisions that could be deducted from the Constitution itself.

Keywords: constitution, court, law, rights

Procedia PDF Downloads 415

Authors: Alaa Osman, Sara Elgazzar, Breksal Elmiligy

Abstract:

The Supply Chain Operation Reference (SCOR) model is considered one of the most widely implemented supply chain performance measurement systems (SCPMSs). Several studies have been proposed on the SCOR model adaptation in developed countries context; while there is a limited availability of previous work on the SCPMSs application generally and the SCOR model specifically in developing nations. This paper presents a research agenda on the SCOR model adaptation in the developing countries. It aims at investigating the challenges of adapting the SCOR model to manage and measure supply chain performance in developing countries. The research will exemplify the system in the Egyptian automotive sector to gain a comprehensive understanding of how the application of the SCOR model can affect the performance of automotive companies in Egypt, with a necessary understanding of challenges and obstacles faced the adaptation of the model in the Egyptian supply chain context. An empirical study was conducted on the Egyptian automotive sector in three companies considering three different classes: BMW, Hyundai and Brilliance. First, in-depth interviews were carried out to gain an insight into the implementation and the relevance of the concepts of supply chain management and performance measurement in the Egyptian automotive industry. Then, a formal survey was designed based on the SCOR model five main processes (plan, source, make, deliver and return) and best practices to investigate the challenges and obstacles faced the adaptation of the SCOR model in the Egyptian automotive supply chain. Finally, based on the survey results, the appropriate best practices for each process were identified in order to overcome the SCOR model adaptation challenges. The results showed that the implementation of the SCOR model faced different challenges and unavailability of the required enablers. The survey highlighted the low integration of end-to-end supply chain, lacks commitment for the innovative ideas and technologies, financial constraints and lack of practical training and support as the main challenges faced the adaptation of the SCOR model in the Egyptian automotive supply chain. The research provides an original contribution to knowledge by proposing a procedure to identify challenges encountered during the process of SCOR model adoption which can pave a way for further research in the area of SCPMSs adaptation, particularly in the developing countries. The research can help managers and organizations to identify obstacles and difficulties of the SCOR model adaptation, subsequently this can facilitate measuring the improved performance or changes in the organizational performance.

Keywords: automotive sector, developing countries, SCOR model, supply chain performance

Procedia PDF Downloads 351

Authors: Emre Kishalı, Neslihan TürkmenoğLu Bayraktar

Abstract:

Historical buildings may face various impacts throughout their life cycle. There have been environmental, structural, public works actions on old monuments influencing sustainability and maintenance issues. As a result, ancient monuments can have been undergone various changes in the context of restoration and repair. Currently, these buildings face integrated conditions including city planning macro solutions, old intervention methods, modifications in building envelope and artefacts in terms of conservation. Moreover, documentation of phases is an essential for assessing the historical building, yet it can result in highly complicated and interwoven issues. Herein, two monuments constructed in the 16th century are selected as case studies in Kocaeli, Turkey which are located in different micro climatic conditions and/or exposed to different interventions and which are important for the city as cultural property. Pertev Paşa Mosque (also known as Yenicuma Mosque) -constructed by Architect Sinan-; Gebze Çoban Mustafa Paşa Mosque -constructed in 1523 and known as the work of Architect Sinan but various names asserted as the architect of building according to resources. Active water infiltration and damages, recent material interventions, hidden niches, and foundation techniques of the mosque are investigated via Infrared Thermography under the project of 114K284, “Non-Destructive Test Applications, in the Context of Planned Conservation, through Historical Mosques of Kocaeli: Coban Mustafa Pasa Mosque, Fevziye Mosque and Pertev Pasa Mosque” funded by TUBITAK. It is aimed to reveal active deteriorations on building elements generated by unwanted effects of structural and climatic conditions, historical interventions, and modifications by monitoring the variation of surface temperature and humidity by IRT visualization method which is an important non- destructive process for investigation of monuments in the conservation field in the context of planned conservation. It is also concluded that in-situ monitoring process via IRT through different climatic conditions give substantial information on the behaviour of the envelope to the physical environmental conditions by observation of thermal performance, degradations. However, it is obvious that monitoring of historical buildings cannot be pursued by implementing a single non-destructive technique to have complete data of the structure.

Keywords: IRT, non-destructive test, planned conservation, mosque

Procedia PDF Downloads 326

Authors: Yiu K. C. Jacky, Tang S. K. Eric, W. Y. Tsang, C. Y. Li, C. K. Leung

Abstract:

Objectives : (1) To enhance the competence of nurses on using IPMOE for drug administration; (2) To ensure the transition on implementation of IPMOE in safer and smooth way hospital-wide. Methodology: (1) Well-structured Governance: To make provision for IPMOE implementation, multidisciplinary governance structure at Corporate and Local levels are well established. (2) Staff Engagement: A series of staff engagement events were conducted including Staff Forum, IPMOE Hospital Visit, Kick-off Ceremony and establishment of IPMOE Webpage for familiarizing the forthcoming implementation with frontline staff. (3) Well-organized training program: from Workshop to Workplace Two different IPMOE training programs were tailor-made which aimed at introducing the core features of administration module. Fifty-five identical training classes and six train-the-trainer workshops were organized at 2-3Q 2015. Lending Scheme on IPMOE hardware for hands-on practicing was launched and further extended the training from workshop to workplace. (4) Standard Guidelines and Workflow: the related workflow and guidelines are developed which facilitates users to acquire the competence towards IPMOE and fully familiarize with the standardized contingency plan. (5) Facilities and Equipment: The installations of IPMOE hardware were promptly arranged for rollout. Besides, IPMOE training venue was well-established for staff training. (6) Risk Management Strategy: UCH Medication Safety Forum is organized in December 2015 for sharing “Tricks & Tips” on IPMOE which further disseminate at webpage for arousal of medication safety. Hospital-wide annual audit on drug administration was planned to figure out the compliance and deliberate the rooms for improvement. Results: Through the comprehensive training plan, over 1,000 UCH nurses attended the training program with positive feedback. They agreed that their competence on using IPMOE was enhanced. By the end of November 2015, 28 wards (over 1,000 Inpatient-bed) involving departments of M&G, SUR, O&T and O&G have been successfully rolled out IPMOE in 5-month. A smooth and safe transition of implementation of IPMOE was achieved. Eventually, we all get prepared for embedding IPMOE into daily nursing and work altogether for medication safety at UCH.

Keywords: drug administration, inpatient medication order entry system, medication safety, nursing informatics

Procedia PDF Downloads 315

Authors: Kaesha M. Freyaldenhoven

Abstract:

Chicago is a city in the United States whose cultural identity is largely shaped by public art pieces. Quintessential public works created by internationally renown artists – such as Anish Kapoor’s Cloud Gate in Millennium Park and 'The Picasso' in Daley Plaza – have historically contributed to developing a shared sense of community. In 2017, the city implemented a policy titled 50x50 Neighborhood Arts Project under the Chicago Public Art Plan. The policy promotes investments in contemporary public art to elevate neighborhood cultural assets and create a sense of place. Exclusively community-based artists were commissioned to accomplish the mission of the policy. Administrators felt only local artists would be capable of capturing the true essence of a neighborhood through art. This paper discusses the relationship between the public art and the culture of its respective neighborhood through close examination of aesthetic formal properties and social significance. Research compares the role of international artists with the role of local artists in cultivating the identity of a city through site-specific artworks in Chicago. Methodology unites theoretical research on understanding art and its function in the public space with empirical research on Chicago-based works. Theoretical frameworks provide an art historical foundation to explore the manner in which physical properties convey meaning through the work itself and its placement in an urban setting. Empirical research that examines policy documentation and press announcements released by the Department of Cultural Affairs and Special Events investigates project selection processes pertaining to the artists and neighborhoods. Ethnographies and interviews of individuals from diverse social segments in contemporary Chicago society measure impacts of the works on respective populations. Findings demonstrate works created by local artists activate neighborhoods and inculcate a sense of pride among community residents. Works created by international artists garner widespread media attention that frames the city’s cultural identity across temporal and geographic zones. This research can be utilized to inform future cultural policies pertaining to the commission of public art.

Keywords: Chicago, cultural policy, public art, urban art

Procedia PDF Downloads 104

Authors: Yared Pawlos Woldeyes

Abstract:

Public Relations often referred to as ‘PR’, is the practice of managing the spread of information between an individual or organization, such as a business, government agency, or a nonprofit organization, and the public. Public Relations are important because they help organizations or entities cultivate and maintain meaningful connections with society at large through platforms like print media and social media. Individuals that identify as public relation specialists establish and maintain relationships with an organization’s target audiences, relevant media sources, and opinion leaders. With regard to the challenges, when trying to practice public relations for government institutions, the priority for specialists is often to help members of society exercise a positive attitude and impression of a country’s political systems and practices. If you consider the case of public relations for government entities in Ethiopia there are several factors to consider. First, public relations in Ethiopia are very much driven by a desire to create a good image of the country and prevent the spread of any information that creates a bad image of Ethiopia. Also, the current ruling party dominates public relations in Ethiopia. Unfortunately, this means that more often than not, public relations specialists are forced by the government to spread and mass communicate false information to the public instead of the truth. Any opposition to government’s agenda will result in seriously negative repercussions for public relations specialists. Although public relations is supposed to create a positive and honest relationship between an organization or the government with the public, in Ethiopia, that is not the case. As a result, very few people express an interest in practicing public relations here. Despite this, there is an opportunity for the development of an accountable public relation affairs in developing nations, taking Ethiopian’s case. For instance, the fact that Public relations are provided as a field of study in college or university to produce competent and trained specialists, the enormous contribution of good communication to the public developmental efforts linking the government to the people, and the better payment to employees of public relation officers are some of them. Therefore, there is a need by the respective stakeholders to work in coalition in raising awareness of the youth regarding the importance of a responsible public relations officer to the country’s developmental efforts, encouragement of Civil Society Organizations working in promoting free press and expression of ideas, improving the governmental structure to be transparent and that allows independent officers, and hosting international conferences on public relations practice so that the specialists can exchange knowledge and skills.

Keywords: developing nations, Ethiopia, public relations, public relations specialist

Procedia PDF Downloads 200

Authors: Anvesh Gaddam, Amit Agrawal, Suhas Joshi, Mark Thompson

Abstract:

An increase in surface area to volume ratio with a decrease in characteristic length scale, leads to a rapid increase in pressure drop across the microchannel. Texturing the microchannel surfaces reduce the effective surface area, thereby decreasing the pressured drop. Surface texturing introduces two wetting states: a metastable Cassie-Baxter state and stable Wenzel state. Predicting wetting transition in textured microchannels is essential for identifying optimal parameters leading to maximum drag reduction. Optical methods allow visualization only in confined areas, therefore, obtaining whole-field information on wetting transition is challenging. In this work, we propose a non-invasive method to capture wetting transitions in textured microchannels under flow conditions. To this end, we tracked the behavior of the Poiseuille number Po = f.Re, (with f the friction factor and Re the Reynolds number), for a range of flow rates (5 < Re < 50), and different wetting states were qualitatively demarcated by observing the inflection points in the f.Re curve. Microchannels with both longitudinal and transverse ribs with a fixed gas fraction (δ, a ratio of shear-free area to total area) and at a different confinement ratios (ε, a ratio of rib height to channel height) were fabricated. The measured pressure drop values for all the flow rates across the textured microchannels were converted into Poiseuille number. Transient behavior of the pressure drop across the textured microchannels revealed the collapse of liquid-gas interface into the gas cavities. Three wetting states were observed at ε = 0.65 for both longitudinal and transverse ribs, whereas, an early transition occurred at Re ~ 35 for longitudinal ribs at ε = 0.5, due to spontaneous flooding of the gas cavities as the liquid-gas interface ruptured at the inlet. In addition, the pressure drop in the Wenzel state was found to be less than the Cassie-Baxter state. Three-dimensional numerical simulations confirmed the initiation of the completely wetted Wenzel state in the textured microchannels. Furthermore, laser confocal microscopy was employed to identify the location of the liquid-gas interface in the Cassie-Baxter state. In conclusion, the present method can overcome the limitations posed by existing techniques, to conveniently capture wetting transition in textured microchannels.

Keywords: drag reduction, Poiseuille number, textured surfaces, wetting transition

Procedia PDF Downloads 144

Authors: Natalia Sypion-Dutkowska

Abstract:

Abstract — The main research objective of the paper is to discover the relationship between the age groups of residents and crime in particular districts of a large city. The basic analytical tool is specific crime rates, calculated not in relation to the total population, but for age groups in a different social situation - property, housing, work, and representing different generations with different behavior patterns. They are the communities from which criminals and victims of crimes come. The analysis of literature and national police reports gives rise to hypotheses about the ability of a given age group to generate crime as a source of offenders and as a group of victims. These specific indicators are spatially differentiated, which makes it possible to detect socio-demographic determinants of spatial patterns of urban crime. A multi-feature classification of districts was also carried out, in which specific crime rates are the diagnostic features. In this way, areas with a similar structure of socio-demographic determinants of spatial patterns on urban crime were designated. The case study is the city of Szczecin in Poland. It has about 400,000 inhabitants and its area is about 300 sq km. Szczecin is located in the immediate vicinity of Germany and is the economic, academic and cultural capital of the region. It also has a seaport and an airport. Moreover, according to ESPON 2007, Szczecin is the Transnational and National Functional Urban Area. Szczecin is divided into 37 districts - auxiliary administrative units of the municipal government. The population of each of them in 2015-17 was divided into 8 age groups: babes (0-2 yrs.), children (3-11 yrs.), teens (12-17 yrs.), younger adults (18-30 yrs.), middle-age adults (31-45 yrs.), older adults (46-65 yrs.), early older (66-80) and late older (from 81 yrs.). The crimes reported in 2015-17 in each of the districts were divided into 10 groups: fights and beatings, other theft, car theft, robbery offenses, burglary into an apartment, break-in into a commercial facility, car break-in, break-in into other facilities, drug offenses, property damage. In total, 80 specific crime rates have been calculated for each of the districts. The analysis was carried out on an intra-city scale, this is a novel approach as this type of analysis is usually carried out at the national or regional level. Another innovative research approach is the use of specific crime rates in relation to age groups instead of standard crime rates. Acknowledgments: This research was funded by the National Science Centre, Poland, registration number 2019/35/D/HS4/02942.

Keywords: age groups, determinants of crime, spatial crime pattern, urban crime

Procedia PDF Downloads 158

Authors: K. Al Ammari, B. G. Clarke

Abstract:

Soil improvement using vibro stone column techniques consists of two main parts: (1) the installed load bearing columns of well-compacted, coarse-grained material and (2) the improvements to the surrounding soil due to vibro compaction. Extensive research work has been carried out over the last 20 years to understand the improvement in the composite foundation performance due to the second part mentioned above. Nevertheless, few of these studies have tried to quantify some of the key design parameters, namely the changes in the stiffness and stress state of the treated soil, or have consider these parameters in the design and calculation process. Consequently, empirical and conservative design methods are still being used by ground improvement companies with a significant variety of results in engineering practice. Two-dimensional finite element study to develop an axisymmetric model of a single stone column reinforced foundation was performed using PLAXIS 2D AE to quantify the effect of the vibro installation of this column in soft saturated clay. Settlement and bearing performance were studied as an essential part of the design and calculation of the stone column foundation. Particular attention was paid to the large deformation in the soft clay around the installed column caused by the lateral expansion. So updated mesh advanced option was taken in the analysis. In this analysis, different degrees of stone column lateral expansions were simulated and numerically analyzed, and then the changes in the stress state, stiffness, settlement performance and bearing capacity were quantified. It was found that application of radial expansion will produce a horizontal stress in the soft clay mass that gradually decrease as the distance from the stone column axis increases. The excess pore pressure due to the undrained conditions starts to dissipate immediately after finishing the column installation, allowing the horizontal stress to relax. Changes in the coefficient of the lateral earth pressure K ٭, which is very important in representing the stress state, and the new stiffness distribution in the reinforced clay mass, were estimated. More encouraging results showed that increasing the expansion during column installation has a noticeable effect on improving the bearing capacity and reducing the settlement of reinforced ground, So, a design method should include this significant effect of the applied lateral displacement during the stone column instillation in simulation and numerical analysis design.

Keywords: bearing capacity, design, installation, numerical analysis, settlement, stone column

Procedia PDF Downloads 361

Authors: Edwin Calderon-Mendoza, Patrick Schweitzer, Serge Weber

Abstract:

Series arc faults appear frequently and unpredictably in low voltage distribution systems. Many methods have been developed to detect this type of faults and commercial protection systems such AFCI (arc fault circuit interrupter) have been used successfully in electrical networks to prevent damage and catastrophic incidents like fires. However, these devices do not allow series arc faults to be located on the line in operating mode. This paper presents a location algorithm for series arc fault in a low-voltage indoor power line in an AC 230 V-50Hz home network. The method is validated through simulations using the MATLAB software. The fault location method uses electrical parameters (resistance, inductance, capacitance, and conductance) of a 49 m indoor power line. The mathematical model of a series arc fault is based on the analysis of the V-I characteristics of the arc and consists basically of two antiparallel diodes and DC voltage sources. In a first step, the arc fault model is inserted at some different positions across the line which is modeled using lumped parameters. At both ends of the line, currents and voltages are recorded for each arc fault generation at different distances. In the second step, a fault map trace is created by using signature coefficients obtained from Kirchhoff equations which allow a virtual decoupling of the line’s mutual capacitance. Each signature coefficient obtained from the subtraction of estimated currents is calculated taking into account the Discrete Fast Fourier Transform of currents and voltages and also the fault distance value. These parameters are then substituted into Kirchhoff equations. In a third step, the same procedure described previously to calculate signature coefficients is employed but this time by considering hypothetical fault distances where the fault can appear. In this step the fault distance is unknown. The iterative calculus from Kirchhoff equations considering stepped variations of the fault distance entails the obtaining of a curve with a linear trend. Finally, the fault distance location is estimated at the intersection of two curves obtained in steps 2 and 3. The series arc fault model is validated by comparing current registered from simulation with real recorded currents. The model of the complete circuit is obtained for a 49m line with a resistive load. Also, 11 different arc fault positions are considered for the map trace generation. By carrying out the complete simulation, the performance of the method and the perspectives of the work will be presented.

Keywords: indoor power line, fault location, fault map trace, series arc fault

Procedia PDF Downloads 119

Authors: Mohammad K. Abedin, Mohammad Shahjahan, Zeenat Sultana, Tawfique Jahan, Jesmin Akter

Abstract:

To strengthen social and behavior change communication (SBCC) capacity of Ministry of Health and Family Welfare (MoHFW) of the Government of Bangladesh, BCCP/BKMI developed two eLearning courses providing opportunities for professional development of SBCC Program Managers who have no access to training or refreshers training. The two eLearning courses – Message and Material Development (MMD) and Monitoring and Evaluation (MandE) of SBCC programs – went online in September 2015, where all users could register their participation so results could be monitored. Methodology: To assess the uses of these courses a randomly selected sample was collected to run a pre and post-test analyses and a phone survey were conducted. Systematic random sampling was used to select a sample of 75 MandE and 25 MMD course participants from a sampling frame of 179 and 51 respectively. Results: As of September 2016, more than 179 learners have completed the MandE course, and 49 learners have completed the MMD course. The users of these courses are program managers, university faculty members, and students. Encouraging results were revealed from the analysis of pre and post-test scores and a phone survey three months after course completion. Test scores suggested a substantial increase in knowledge. The pre-test scores findings suggested that about 19% learners scored high on the MandE. The post-test scores finding indicated a high score (92%) of the sample across 4 modules of MandE. For MMD course in pre-test scoring, 30% of the learners scored high, and 100% scored high at the post-test. It was found that all the learners in the phone survey have discussed the courses. Most of the sharing occurred with colleagues and friends, usually through face to face (70%) interaction. The learners reported that they did recommend the two courses to concerned people. About 67% MandE and 76% MMD learners stated that the concepts that they had to learn during the course were put into practice in their work settings. The respondents for both MandE and MMD courses have provided a valuable set of suggestions that would further strengthen the courses. Conclusions: The study showed that the initiative offered ample opportunities to build capacity in various ways in which the eLearning courses were used. It also highlighted the importance of scaling up these efforts to further strengthen the outcomes.

Keywords: e-learning course, message & material development, monitoring & evaluation, social and behavior change communication

Procedia PDF Downloads 273

Authors: Cláudia Pereira, Lívia Boeschenstein

Abstract:

This article aims to present an analysis of rock band t-shirts as an element that claims a certain identity in modern-contemporary culture. This work focuses on the study of t-shirts that display the name, related elements and the logo of punk band The Ramones, because of its strong presence in the collective mind along the last decades. As we shall see, it is possible to observe a phenomenon of symbolic transition from the original cultural place of that object. At first, it was a piece of cloth that had been part of a specific subculture and then it became just a generic item diluted by the mainstream. This symbolic transitional phenomenon is significant in many ways and will be discussed furthermore. For the analysis, we begin with a brief introduction to the history of the band, followed by the study about the vintage rock band T-shirts and their meanings. From there, we will turn to a historical contextualization of band T-shirts as a subcultural item and to its redefinition after the appropriation made by the mainstream. To guide this reasoning, it will be used theories about the styles, subcultures and youth culture and about material culture from an anthropological perspective. In addition, we shall see the theories and concepts of social representations in order to understand the ways of using the Ramones’s T-shirt as a representative element of a fashionable style. This T-shirt, after being resignified by the standardization and the massive consumption, no longer symbolizes the punk movement, its behavioral motivations and original policies. Also has little to do with the rage the working class suburbs of London or New York. It seems to be a mute and vague sign of a restricted rebellion, foreseen and framed establishing a stylistic contrast to the designer clothes and good behavior predicted by establishment. It's an item that composes a specific style available on the market, but at the same time is accepted by the mainstream and provides a subcultural association that has some prestige in society. Another perspective is that of resignification loop. As the same way that punk resignified the conventional goods for their own social standards, fashion resignifies what was said to be an object of a subculture and absorbs in their own mass culture standards. Therefore, outsiders to the punk phenomenon wearing Ramones’s T-shirts can be perceived negatively by subcultural members, but at the same time are well received by those who are partially unaware or completely out of subcultural context. For the general public, the stamp of the Ramones’s logo happens to be appreciated as a diffuse allusion to a punk style, since its original meaning has being entirely neutralized.

Keywords: social representations, subcultures, material culture, punk

Procedia PDF Downloads 366

Authors: Arezoo Rahmani, Rinez Thapa, Juha-Matti Aalto, Petri Turhanen, Jouko Vepsalainen, Vesa-PekkaLehto, Joakim Riikonen

Abstract:

Production of Scandium (Sc) is a complicated process because Sc is found only in low concentrations in ores and the concentration of Sc is very low compared with other metals. Therefore, utilization of typical extraction processes such as solvent extraction is problematic in scandium extraction. The Adsorption/desorption method can be used, but it is challenging to prepare materials, which have good selectivity, high adsorption capacity, and high stability. Therefore, efficient and environmentally friendly methods for Sc extraction are needed. In this study, the nanoporous composite material was developed for extracting Sc from an Sc ore. The nanoporous composite material offers several advantageous properties such as large surface area, high chemical and mechanical stability, fast diffusion of the metals in the material and possibility to construct a filter out of the material with good flow-through properties. The nanoporous silicon material was produced by first stabilizing the surfaces with a silicon carbide layer and then functionalizing the surface with bisphosphonates that act as metal chelators. The surface area and porosity of the material were characterized by N₂ adsorption and the morphology was studied by scanning electron microscopy (SEM). The bisphosphonate content of the material was studied by thermogravimetric analysis (TGA). The concentration of metal ions in the adsorption/desorption experiments was measured with inductively coupled plasma mass spectrometry (ICP-MS). The maximum capacity of the material was 25 µmol/g Sc at pH=1 and 45 µmol/g Sc at pH=3, obtained from adsorption isotherm. The selectivity of the material towards Sc in artificial solutions containing several metal ions was studied at pH one and pH 3. The result shows good selectivity of the nanoporous composite towards adsorption of Sc. Scandium was less efficiently adsorbed from solution leached from the ore of Sc because of excessive amounts of iron (Fe), aluminum (Al) and titanium (Ti) which disturbed the adsorption process. For example, the concentration of Fe was more than 4500 ppm, while the concentration of Sc was only three ppm, approximately 1500 times lower. Precipitation methods were developed to lower the concentration of the metals other than Sc. Optimal pH for precipitation was found to be pH 4. The concentration of Fe, Al and Ti were decreased by 99, 70, 99.6%, respectively, while the concentration of Sc decreased only 22%. Despite the large reduction in the concentration of other metals, more work is needed to further increase the relative concentration of Sc compared with other metals to efficiently extract it using the developed nanoporous composite material. Nevertheless, the developed material may provide an affordable, efficient and environmentally friendly method to extract Sc on a large scale.

Keywords: adsorption, nanoporous silicon, ore solution, scandium

Procedia PDF Downloads 128