Search results for: Learning materials

Authors: Y. Lu, L. Liu, J. Guo

Abstract:

Monolayer graphene and dichaclogenide semiconductor materials attract extensive research interest for potential nanoelectronics applications. The ultimate scaling limit of double gate MoS2 Field-Effect-Transistors (FETs) with a monolayer thin body is examined and compared with ultra-thin-body Si FETs by using self-consistent quantum transport simulation in the presence of phonon scattering. Modelling of phonon scattering, quantum mechanical effects, and self-consistent electrostatics allows us to accurately assess the performance potential of monolayer MoS2 FETs. The results revealed that monolayer MoS2 FETs show 52% smaller Drain Induced Barrier Lowering (DIBL) and 13% Smaller Sub-Threshold Swing (SS) than 3 nm-thick-body Si FETs at a channel length of 10 nm with the same gating. With a requirement of SS<100mV/dec, the scaling limit of monolayer MoS2 FETs is assessed to be 5 nm, comparing with 8nm of the ultra-thin-body Si counterparts due to the monolayer thin body and higher effective mass which reduces direct source-to-drain tunnelling. By comparing with the ITRS target for high performance logic devices of 2023; double gate monolayer MoS2 FETs can fulfil the ITRS requirements.

Keywords: nanotransistors, monolayer 2D materials, quantum transport, scaling limit

Procedia PDF Downloads 219

Authors: Alaa Fezai, Anuj Sharma, Wolfgang Mueller-Hirsch, André Zimmermann

Abstract:

Viscoelastic materials have been widely used in the automotive industry over the last few decades with different functionalities. Besides their main application as a simple and efficient surface damping treatment, they may ensure optimal operating conditions for on-board electronics as thermal interface or sealing layers. The dynamic behavior of viscoelastic materials is generally dependent on many environmental factors, the most important being temperature and strain rate or frequency. Prior to the reliability analysis of systems including viscoelastic layers, it is, therefore, crucial to accurately predict the dynamic and lifetime behavior of these materials. This includes the identification of the dynamic material parameters under critical temperature and frequency conditions along with a precise damage localization and identification methodology. The goal of this work is twofold. The first part aims at applying an inverse viscoelastic material-characterization approach for a wide frequency range and under different temperature conditions. For this sake, dynamic measurements are carried on a single lap joint specimen using an electrodynamic shaker and an environmental chamber. The specimen consists of aluminum beams assembled to adapter plates through a viscoelastic adhesive layer. The experimental setup is reproduced in finite element (FE) simulations, and frequency response functions (FRF) are calculated. The parameters of both the generalized Maxwell model and the fractional derivatives model are identified through an optimization algorithm minimizing the difference between the simulated and the measured FRFs. The second goal of the current work is to guarantee an on-line detection of the damage, i.e., delamination in the viscoelastic bonding of the described specimen during frequency monitored end-of-life testing. For this purpose, an inverse technique, which determines the damage location and size based on the modal frequency shift and on the change of the mode shapes, is presented. This includes a preliminary FE model-based study correlating the delamination location and size to the change in the modal parameters and a subsequent experimental validation achieved through dynamic measurements of specimen with different, pre-generated crack scenarios and comparing it to the virgin specimen. The main advantage of the inverse characterization approach presented in the first part resides in the ability of adequately identifying the material damping and stiffness behavior of soft viscoelastic materials over a wide frequency range and under critical temperature conditions. Classic forward characterization techniques such as dynamic mechanical analysis are usually linked to limitations under critical temperature and frequency conditions due to the material behavior of soft viscoelastic materials. Furthermore, the inverse damage detection described in the second part guarantees an accurate prediction of not only the damage size but also its location using a simple test setup and outlines; therefore, the significance of inverse numerical-experimental approaches in predicting the dynamic behavior of soft bonding layers applied in automotive electronics.

Keywords: damage detection, dynamic characterization, inverse approaches, vibration testing, viscoelastic layers

Procedia PDF Downloads 194

Authors: Mahdi Taghipour Masoumi, Ali Abdi Kordani, Mahmoud Nazirizad

Abstract:

Geosynthetics utilization plays an important role in the construction of highways with no additive layers, such as asphalt concrete or cement concrete, or in a subgrade layer which affects the bearing capacity of unbounded layers. This laboratory experimental study was carried out to evaluate changes in the load bearing capacity of reinforced soil with these materials in highway roadbed with regard to geotextile properties. California Bearing Ratio (CBR) test samples were prepared with two types of soil: Clayey and sandy containing non-reinforced and reinforced soil. The samples comprised three types of geotextiles with different characteristics (150, 200, 300 g/m²) and depths (H= 5, 10, 20, 30, 50, 100 mm), and were grouped into two forms, one-layered and two-layered, based on the sample materials in order to perform defined tests. The results showed that the soil bearing characteristics increased when one layer of geotextile was used in clayey and sandy samples reinforced by geotextile. However, the bearing capacity of the soil, in the presence of a geotextile layer material with depth of more than 30 mm, had no remarkable effect. Furthermore, when the two-layered geotextile was applied in material samples, although it increased the soil resistance, it also showed that through the addition of a number or weights of geotextile into samples, the natural composition of the soil changed and the results are unreliable.

Keywords: reinforced soil, geosynthetics, geotextile, transportation capacity, CBR experiments

Procedia PDF Downloads 274

Authors: Aylin Sahin, Yasemin Kilic, Abdulkadir Sari, Burcu Duymaz, Mustafa Kara

Abstract:

Foam glass is an innovative material which composed of glass and carbon/carbonate based minerals; and has incomparable properties like light weight, high thermal insulation and cellular structure with sufficient rigidity. In the present study, the effects of the glass type and mineral addition on the foam glass properties were investigated. Nano sized SiC was fixed as foaming agent at the whole of the samples, mixed glass waste and sheet glass were selectively used as glass sources; finally Al₂O₃ was optionally used as mineral additive. These raw material powders were mixed homogenously, pressed at same pressure and sintered at same schedule. Finally, obtained samples were characterized based on the required properties of foam glass material, and optimum results were determined. At the end of the study, 0.049 W/mK thermal conductivity, 72 % porosity, and 0.21 kg/cm² apparent density with 2.41 MPa compressive strength values were achieved with using nano sized SiC, sheet glass and Al₂O₃ mineral additive. It can be said that the foam glass materials can be preferred as an alternative insulation material rather than polymeric based conventional insulation materials because of supplying high thermal insulation properties without containing unhealthy chemicals and burn risks.

Keywords: foam glass, foaming, silicon carbide, waste glass

Procedia PDF Downloads 352

Authors: Boriana Karamanova, Svetlana Veleva, Luybomir Soserov, Ana Arenillas, Francesco Lufrano, Antonia Stoyanova

Abstract:

Supercapacitors have received a lot of research attention and are promising energy storage devices due to their high power and long cycle life. In order to developed an advanced device with significant capacity for storing charge and cheap carbon materials, efforts must focus not only on improving synthesis by controlling the morphology and pore size but also on improving electrode-electrolyte compatibility of the resulting systems. The present study examines the relationship between the surface chemistry of two activated carbon xerogels, the electrolyte type, and the electrochemical properties of supercapacitors. Activated carbon xerogels were prepared by varying the initial pH of the resorcinol-formaldehyde aqueous solution. The materials produced are physicochemical characterized by DTA/TGA, porous characterization, and SEM analysis. The carbon xerogel based electrodes were prepared by spreading over glass plate a slurry containing the carbon gel, graphite, and poly vinylidene difluoride (PVDF) binder. The layer formed was dried consecutively at different temperatures and then detached by water. After, the layer was dried again to improve its mechanical stability. The developed electrode materials and the Aquivion® E87-05S membrane (Solvay Specialty Polymers), socked in Na2SO4 as a polymer electrolyte, were used to assembly the solid-state supercapacitor. Symmetric supercapacitor cells composed by same electrodes and 1 M KOH electrolytes are also assembled and tested for comparison. The supercapacitor performances are verified by different electrochemical methods - cyclic voltammetry, galvanostatic charge/discharge measurements, electrochemical impedance spectroscopy, and long-term durability tests in neutral and alkaline electrolytes. Specific capacitances, energy, and power density, energy efficiencies, and durability were compared into studied supercapacitors. Ex-situ physicochemical analyses on the synthesized materials have also been performed, which provide information about chemical and structural changes in the electrode morphology during charge / discharge durability tests. They are discussed on the basis of electrode-electrolyte interaction. The obtained correlations could be of significance in order to design sustainable solid-state supercapacitors with high power and energy density. Acknowledgement: This research is funded by the Ministry of Education and Science of Bulgaria under the National Program "European Scientific Networks" (Agreement D01-286 / 07.10.2020, D01-78/30.03.2021). Authors gratefully acknowledge.

Keywords: carbon xerogel, electrochemical tests, neutral and alkaline electrolytes, supercapacitors

Procedia PDF Downloads 120

Authors: M. S. Said, J. A. Ghani, C. H. Che Hassan, N. N. Wan, M. A. Selamat, R. Othman

Abstract:

Metal Matrix Composite (MMCs) have attracted considerable attention as a result of their ability to provide high strength, high modulus, high toughness, high impact properties, improved wear resistance and good corrosion resistance than unreinforced alloy. Aluminium Silicon (Al/Si) alloys Metal Matrix composite (MMC) has been widely used in various industrial sectors such as transportation, domestic equipment, aerospace, military, construction, etc. Aluminium silicon alloy is MMC reinforced with aluminium nitride (AlN) particle and becomes a new generation material for automotive and aerospace applications. The AlN material is one of the advanced materials with light weight, high strength, high hardness and stiffness qualities which have good future prospects. However, the high degree of ceramic particles reinforcement and the irregular nature of the particles along the matrix material that contribute to its low density, is the main problem that leads to the machining difficulties. This paper examines tool wear when milling AlSi/AlN Metal Matrix Composite using a TiB2 coated carbide cutting tool. The volume of the AlN reinforced particle was 10%. The milling process was carried out under dry cutting condition. The TiB2 coated carbide insert parameters used were the cutting speed of (230 m/min, feed rate 0.4mm tooth, DOC 0.5mm, 300 m/min, feed rate 0.8mm/tooth, DOC 0.5mm and 370 m/min, feed rate 0.8, DOC 0.4m). The Sometech SV-35 video microscope system was used for tool wear measurements respectively. The results have revealed that the tool life increases with the cutting speed (370 m/min, feed rate 0.8 mm/tooth and depth of cut 0.4mm) constituted the optimum condition for longer tool life which is 123.2 min. While at medium cutting speed, it is found that the cutting speed of 300m/min, feed rate 0.8 mm/tooth and depth of cut 0.5mm only 119.86 min for tool wear mean while the low cutting speed give 119.66 min. The high cutting speed gives the best parameter for cutting AlSi/AlN MMCs materials. The result will help manufacture to machining the AlSi/AlN MMCs materials.

Keywords: AlSi/AlN Metal Matrix Composite milling process, tool wear, TiB2 coated carbide tool, manufacturing engineering

Procedia PDF Downloads 412

Authors: Shakila Singh

Abstract:

Sexual harassment continues to be a problem both in educational institutions and workplaces with the main victims being women and the main perpetrators being men. The achievement of quality education demands to create safe learning spaces for all students and requires extensive and integrated interventions. This article draws on the data from a broader study that aims to create safer learning environments at university by addressing gender violence. It attempts to understand male students’ perspectives about their role in sexual harassment on the campus. It is a move away from interventions that place the responsibility of prevention of sexual harassment, on women. The study adopts an interpretive paradigm within a qualitative approach. The sample comprises twenty male university students who were purposively selected because they live in the campus residences. The main data generation methods included focus group discussions and individual interviews. Findings show that while many male students agree that victims of sexual harassment are mainly women, they also suggest that men are victims of sexual harassment by women. Male students have varying understandings of what constitutes sexual harassment. They position themselves as victims who feel harassed by women’s dress and behaviour. Male students also felt under pressure by sexual advances made by women that forced them to comply in order to protect their masculinity. This article argues that social norms of masculinity are powerful drivers of behaviour that play a key role in the perpetuation of sexual harassment. Male students who feel strongly against sexual harassment of female students are constrained by their masculinities in their ability to act against it. Effective interventions need to actively engage students in reflecting on and challenging social and cultural norms that contribute to violent expressions and to develop alternatives with them.

Keywords: gender violence, male students, sexual harassment, university students

Procedia PDF Downloads 184

Authors: Eunice Tang

Abstract:

The main focus of this study is investigating introvert and extrovert university students’ perception of the use of interactive digital tools (such as Padlet and Mentimeter) in a face-to-face English for Specific Purposes (ESP) class after all classes in the university had been switched to online mode for three semesters. The subjects of the study were business students from three ESP classes at The Hong Kong University of Science and Technology. The basic tool for data collection was an anonymous online survey, which included 3 required multiple-choice questions and 3 open questions (2 required; 1 optional) about the effects of interactive digital tools on their amount of contribution to the class discussions, their perception of the role of interactive digital tools to the sharing of ideas and whether the students considered themselves introvert or extrovert. The online survey will be emailed to all 54 students in the three ESP classes and subjected to a three-week data collection period. The survey results will then be analyzed qualitatively, particularly on the effect the use of interactive digital tools had on the amount of contribution to the class among introvert and extrovert students, their perception of a language class with and without digital tools and most importantly, the implication to educators about how interactive digital tools can be used (or not) to cater for the needs of the introvert and extrovert students. The pandemic has given educators various opportunities to use interactive digital tools in class, especially in an online environment. It is interesting for educators to explore the potential of such tools when classes are back face-to-face. This research thus offers the students’ perspective on using interactive digital tools in a face-to-face classroom. While a lot has been said about introverted students responding positively to digital learning online, the student's perception of their own personality collected in the survey and the digital impact tools have on their contribution to class may shed some light on the potential of interactive digital tools in a post-pandemic era.

Keywords: psychology for language learning, interactive digital tools, personality-based investigation, ESP

Procedia PDF Downloads 166

Authors: Hoa Pham

Abstract:

Code switching, which can be described as the use of students’ first language in second language classrooms, has long been a controversial topic in the area of language teaching and second language acquisition. While this has been widely investigated across different contexts, little empirical research has been undertaken in Vietnam. The findings of this study contribute to our understanding of bilingual discourse and code switching practices in content and language integrated classrooms, which has significant implications for language teaching and learning in general and in particular for language pedagogy at tertiary level in Vietnam. This study examines the accounts the teachers articulated for their code switching practices in content-based Business English in Vietnam. Data were collected from five teachers through the use of stimulated recall interviews facilitated by the video data to garner the teachers' cognitive reflection, and allowed them to vocalise the motivations behind their code switching behaviour in particular contexts. The literature has recommended that when participants are provided with a large amount of stimuli or cues, they will experience an original situation again in their imagination with great accuracy. This technique can also provide a valuable "insider" perspective on the phenomenon under investigation which complements the researcher’s "outsider" observation. This can create a relaxed atmosphere during the interview process, which in turn promotes the collection of rich and diverse data. Also, participants can be empowered by this technique as they can raise their own concerns and discuss instances which they find important or interesting. The data generated through this study were analysed using a constant comparative approach. The study found that the teachers indicated their support for the use of code switching in their pedagogical practices. Particularly, as a pedagogical resource, the teachers saw code switching to the L1 playing a key role in facilitating the students' comprehension of both content knowledge and the target language. They believed the use of the L1 accommodates the students' current language competence and content knowledge. They also expressed positive opinions about the role that code switching plays in stimulating students' schematic language and content knowledge, encouraging retention and interest in learning and promoting a positive affective environment in the classroom. The teachers perceived that their use of code switching to the L1 helps them meet the students' language needs and prepares them for their study in subsequent courses and addresses functional needs so that students can cope with English language use outside the classroom. Several factors shaped the teachers' perceptions of their code switching practices, including their accumulated teaching experience, their previous experience as language learners, their theoretical understanding of language teaching and learning, and their knowledge of the teaching context. Code switching was a typical phenomenon in the observed classes and was supported by the teachers in certain contexts. This study reinforces the call in the literature to recognise this practice as a useful instructional resource.

Keywords: codeswitching, language teaching, teacher beliefs, tertiary level

Procedia PDF Downloads 428

Authors: Yung-Hui Tang, Yan-Chiou Ku, Li-Chi Huang

Abstract:

Aim: The aim of this study is to explore the effect of the Humanoid Diagram Teaching (HDT) strategy on novice nurses’ care ability and retention rate. Methods: This study was a quasi-experimental study using two groups concurrently with repeat measurements sample consisted of 24 novice nurses (12 in each experimental and control group) in a medical center in southern Taiwan. Both groups all received regular training program (nursing standard techniques and practices, concept map, mini-CEX, CbD, and clinical education and training), and experimental group added the HDT program. The HDT strategy includes the contents of patients’ body humanoid drawing and discussion for 30 minutes each time, three times a week, and continually for four weeks. The effectiveness of ＨDT was evaluated by mini-CEX, CbD and clinical assessment and retention rate at the 3rd month and 6th month. Results: The novice nurses' care ability were examined, only CbD score in the control group was improved in the 3rd month and with statistical difference, p = .003. The mini-CEX and CbD in the experimental group were significantly improved in both the first and third month with statistical differences p = .00. Although mini-CEX and CbD in the experimental group were higher than the control group, but there was no significant difference p > .05. Retention rate of the experimental group in the third month and sixth month was significantly higher than the control group, and there was a statistically significant difference p < .05. Conclusions: The study reveals that HDT strategy can help novice nurses learning, enhancing their knowledge and technical capability, analytical skills in case-based caring, and retention. The HDT strategy can be served as an effective strategy for novice training for better nurse retention rate.

Keywords: humanoid diagram teaching strategy, novice nurses retention, teaching strategy of nurse retention, visual learning mode

Procedia PDF Downloads 158

Authors: Khaled Al-Badani, Andrew Norbury, Essam Elmshawet, Glynn Rotwell, Ian Jenkinson , James Ren

Abstract:

Micro welding procedures are widely used for joining materials, developing duplex components or functional surfaces, through various methods such as Micro Discharge Welding or Spot Welding process, which can be found in the engineering, aerospace, automotive, biochemical, biomedical and numerous other industries. The relationship between the material properties, structure and processing is very important to improve the structural integrity and the final performance of the welded joints. This includes controlling the shape and the size of the welding nugget, state of the heat affected zone, residual stress, etc. Nowadays, modern high volume productions require the welding of much versatile shapes/sizes and material systems that are suitable for various applications. Hence, an improved understanding of the micro welding process and the digital tools, which are based on computational numerical modelling linking key welding parameters, dimensional attributes and functional performance of the weldment, would directly benefit the industry in developing products that meet current and future market demands. This paper will introduce recent work on developing an integrated experimental and numerical modelling code for micro welding techniques. This includes similar and dissimilar materials for both ferrous and non-ferrous metals, at different scales. The paper will also produce a comparative study, concerning the differences between the micro discharge welding process and the spot welding technique, in regards to the size effect of the welding zone and the changes in the material structure. Numerical modelling method for the micro welding processes and its effects on the material properties, during melting and cooling progression at different scales, will also be presented. Finally, the applications of the integrated numerical modelling and the material development for the digital manufacturing of welding, is discussed with references to typical application cases such as sensors (thermocouples), energy (heat exchanger) and automotive structures (duplex steel structures).

Keywords: computer modelling, droplet formation, material distortion, materials forming, welding

Procedia PDF Downloads 242

Authors: Ghada Elshafei, Abdelazim Negm

Abstract:

Life cycle assessment is a technique to assess the environmental aspects and potential impacts associated with a product, process, or service, by compiling an inventory of relevant energy and material inputs and environmental releases; evaluating the potential environmental impacts associated with identified inputs and releases; and interpreting the results to help you make a more informed decision. In this paper, the life cycle assessment of aluminum and beech wood as two commonly used materials in Egypt for window frames are heading, highlighting their benefits and weaknesses. Window frames of the two materials have been assessed on the basis of their production, energy consumption and environmental impacts. It has been found that the climate change of the windows made of aluminum and beech wood window, for a reference window (1.2m × 1.2m), are 81.7 mPt and - 52.5 mPt impacts respectively. Among the most important results are: fossil fuel consumption, potential contributions to the green building effect and quantities of solid waste tend to be minor for wood products compared to aluminum products; incineration of wood products can cause higher impacts of acidification and eutrophication than aluminum, whereas thermal energy can be recovered.

Keywords: aluminum window, beech wood window, green building, life cycle assessment, life cycle analysis, SimaPro software, window frame

Procedia PDF Downloads 431

Authors: Ayodele Oluwole Alejo

Abstract:

Wall finishes are the term to describe an application over a wall surface to provide a suitable surface. Wall finishes are smelt, touched and seen by building occupiers even colour and design affects the user psychology and the atmosphere of our building. Building users/owners seem not to recognize the function of various wall finishes in building and factors to be considered in selecting them suitable for the type and purpose of proposed buildings. Therefore, defects such as deterioration, dampness, and stain may occur when comparisons of wall finishes are not made before the selection of appropriate materials at the design stage with knowledge of the various factors that may hinder the performance or maintenance culture of proposed building of a particular location. This research work investigates and compares various wall finishes in building. Buildings in Ondo state, Nigeria were used as the target area to conduct the research works. The factors bearing on various wall finishes were analyzed to find out their individual and collective impact using suitable analytical tools. The findings revealed that paint with high percentage score was the most preferred wall finishes, whereas wall paper was ranked the least by the respondent findings, Factors considered most in the selection of wall finishes was durability with the highest ranking percentage and least was the cost. The study recommends that skilled worker should carry out operations, quality product should be used and all of wall finishes and materials should be considered before selection.

Keywords: building, construction, design, finishes, wall

Procedia PDF Downloads 117

Authors: Maria Margoudi, Zacharoula Smyraniou

Abstract:

The current paper presents the results of a conducted case study, which was part of the author’s master thesis. During the past few years the number of children diagnosed with Learning Difficulties has drastically augmented and especially the cases of ADHD (Attention Deficit Hyperactivity Disorder). One of the core characteristics of ADHD is a deficit in working memory functions. The review of the literature indicates a plethora of educational software that aim at training and enhancing the working memory. Nevertheless, in the current paper, the possibility of using for the same purpose free, online games will be explored. Another issue of interest is the potential effect of the working memory training to the core symptoms of ADHD. In order to explore the abovementioned research questions, three digital tests are employed, all of which are developed on the E-slate platform by the author, in order to check the level of ADHD’s symptoms and to be used as diagnostic tools, both in the beginning and in the end of the case study. The tools used during the main intervention of the research are free online games for the training of working memory. The research and the data analysis focus on the following axes: a) the presence and the possible change in two of the core symptoms of ADHD, attention and impulsivity and b) a possible change in the general cognitive abilities of the individual. The case study was conducted with the participation of a thirteen year-old, female student, diagnosed with ADHD, during after-school hours. The results of the study indicate positive changes both in the levels of attention and impulsivity. Therefore we conclude that the training of working memory through the use of free, online games has a positive impact on the characteristics of ADHD. Finally, concerning the second research question, the change in general cognitive abilities, no significant changes were noted.

Keywords: ADHD, attention, impulsivity, online games

Procedia PDF Downloads 340

Authors: Saurabh Sharma, Yong Sun, Bruce Vernham

Abstract:

Accurate prediction of NOx emission is a continuous challenge in the field of diesel engine-out emission modeling. Performing experiments for each conditions and scenario cost significant amount of money and man hours, therefore model-based development strategy has been implemented in order to solve that issue. NOx formation is highly dependent on the burn gas temperature and the O₂ concentration inside the cylinder. The current empirical models are developed by calibrating the parameters representing the engine operating conditions with respect to the measured NOx. This makes the prediction of purely empirical models limited to the region where it has been calibrated. An alternative solution to that is presented in this paper, which focus on the utilization of in-cylinder combustion parameters to form a predictive semi-empirical NOx model. The result of this work is shown by developing a fast and predictive NOx model by using the physical parameters and empirical correlation. The model is developed based on the steady state data collected at entire operating region of the engine and the predictive combustion model, which is developed in Gamma Technology (GT)-Power by using Direct Injected (DI)-Pulse combustion object. In this approach, temperature in both burned and unburnt zone is considered during the combustion period i.e. from Intake Valve Closing (IVC) to Exhaust Valve Opening (EVO). Also, the oxygen concentration consumed in burnt zone and trapped fuel mass is also considered while developing the reported model.  Several statistical methods are used to construct the model, including individual machine learning methods and ensemble machine learning methods. A detailed validation of the model on multiple diesel engines is reported in this work. Substantial numbers of cases are tested for different engine configurations over a large span of speed and load points. Different sweeps of operating conditions such as Exhaust Gas Recirculation (EGR), injection timing and Variable Valve Timing (VVT) are also considered for the validation. Model shows a very good predictability and robustness at both sea level and altitude condition with different ambient conditions. The various advantages such as high accuracy and robustness at different operating conditions, low computational time and lower number of data points requires for the calibration establishes the platform where the model-based approach can be used for the engine calibration and development process. Moreover, the focus of this work is towards establishing a framework for the future model development for other various targets such as soot, Combustion Noise Level (CNL), NO₂/NOx ratio etc.

Keywords: diesel engine, machine learning, NOₓ emission, semi-empirical

Procedia PDF Downloads 101

Authors: Amin Kamal Akhnoukh, Lois Zaki Kamel, Magued Mourad Barsoum

Abstract:

The objective of this research is to mitigate and prevent the alkali silica reactivity (ASR) in highway construction projects. ASR is a deleterious reaction initiated when the silica content of the aggregate reacts with alkali hydroxides in cement in the presence of relatively high moisture content. The ASR results in the formation of an expansive white colored gel-like material which forms the destructive tensile stresses inside hardened concrete. In this research, different types of local aggregates available in the State of Arkansas were mixed and mortar bars were poured according to the ASTM specifications. Mortar bars expansion was measured versus time and aggregates with potential ASR problems were detected. Different types of supplementary cementitious materials (SCMs) were used in remixing mortar bars with highly reactive aggregates. Length changes for remixed bars proved that different types of SCMs can be successfully used in reducing the expansive effect of ASR. SCMs percentage by weight is highly dependent on the SCM type. The result of this study will help avoiding future losses due to ASR cracking in construction project and reduce the maintenance, repair, and replacement budgets required for highways network.

Keywords: alkali silica reaction, aggregates, misture, cracks, Mortar Bar Test, supplementary cementitious materials

Procedia PDF Downloads 320

Authors: Oghenerume V. Edah, Damilola T. Aladejana

Abstract:

Entrepreneurship Education is the process of developing and acquiring entrepreneur skills on how to identify a new business and launching the business with the realization of yielding profit optimally. It’s the process of knowing how to take risk and handle challenges that accompanies a new business without the mindset of closing it when it fails. It includes steps to take when a business is recognized, combined with acquiring resources (e.g. finances, labor, land) in the face of risk and launching the new business. Additionally, Entrepreneurship is defined as the ability and willingness to set a business in the event of making profit. It is the act of starting up a business to solve big problems or present a new life-changing solution in the society to generate profit. It’s a process where a business opportunity is identified; planned, acquired and needful steps are taken to launch a business. This involves taking up financial risk, acquiring natural resources, combined with land, capital and building up a team of people who would individually contribute or add value in order to make the new business a success. Moreover, Education is the learning of new skills or value. It’s the acquiring of knowledge and capability of doing new things. It is been able to differentiate what you know and what you don’t know yet. In this modern world, the emergence of entrepreneurship education has been magnificent. An average of 60 percent humans wants to start a business or become an entrepreneur without knowing the steps on how to startup. Moreover, many of them are good starters and they end up failing when the business is not managed well. The introduction of Entrepreneur Education in our world today would change the face of business phenomenally. It would involve the acquisition of entrepreneur skills, knowledge and attitude towards initiating a business venture. The impact of Entrepreneurship Education in our world today would increase the chances of business success because it would generate better entrepreneurs. The skills, values, concept and processes acquired through learning have changed the face of business to a positive direction globally and the impact can be felt. Entrepreneurship can be taught and also can be learnt. Like any skills it can be known.

Keywords: entrepreneurship, education, business, entrepreneur, skills

Procedia PDF Downloads 131

Authors: Lelika Lazarus, Reshma Sookrajh, Kapil S. Satyapal

Abstract:

Reflecting on teaching is commonly cited as a fundamental practice for personal and professional development. Educational research into the scholarship of teaching and learning anatomy includes engaging in discipline specific literature on teaching, reflecting on individual teaching methods and communicating these findings to peers. The aim of this paper is to formally assess the opinions of senior anatomy instructors regarding the state of anatomical knowledge at their respective institutions. The context of the paper derives from ongoing debates about the perceived decline in standards of anatomical knowledge of medical students and postgraduate learners. An open ended questionnaire was devised consisting of eight direct questions seeking opinions on anatomy teaching, knowledge, and potential educational developments and general thoughts on the teaching of anatomy to medical students. These were distributed to senior anatomy Faculty (identified by the author by their affiliation with the Anatomical Society of Southern Africa) based at the eight national medical schools within the country. A number of key themes emerged. Most senior faculty felt that the standard of medical education at their respective institutions was ‘good.’. However, emphasis was also placed on the ‘quality of teaching’ incorporating clinical scenarios. There were also indications that staff are split into those that are keen to do research and those that are happy to provide teaching to medical students as their primary function. Several challenges were also highlighted such as time constraints within the medical curriculum, the lack of cadavers to reinforce knowledge and gain depth perception and lack of appropriately qualified staff. Recommendations included fostering partnerships with both clinicians and medical scientists into the anatomy curriculum thus improving teaching and research.

Keywords: anatomy, education, reflection, teaching

Procedia PDF Downloads 277

Authors: Oyindamola Kayode, Sarah George, Roberto Borrageiro, Mike Shirran

Abstract:

A phenomenon identified by our industrial partner has experienced sag on AA3104 can body stock (CBS) transfer bar during transportation of the slab from the breakdown mill to the finishing mill. Excessive sag results in bottom scuffing of the slab onto the roller table, resulting in surface defects on the final product. It has been found that increasing the strain rate on the breakdown mill final pass results in a slab resistant to sag. The creep response for materials hot deformed at different Zener–Holloman parameter values needs to be evaluated experimentally to gain better understanding of the operating mechanism. This study investigates this identified phenomenon through laboratory simulation of the breakdown mill conditions for various strain rates by utilizing the Gleeble at UCT Centre for Materials Engineering. The experiment will determine the creep response for a range of conditions as well as quantifying the associated material microstructure (sub-grain size, grain structure etc). The experimental matrices were determined based on experimental conditions approximate to industrial hot breakdown rolling and carried out on the Gleeble 3800 at the Centre for Materials Engineering, University of Cape Town. Plane strain compression samples were used for this series of tests at an applied load that allow for better contact and exaggerated creep displacement. A tantalum barrier layer was used for increased conductivity and decreased risk of anvil welding. One set of tests with no in-situ hold time was performed, where the samples were quenched after deformation. The samples were retained for microstructure analysis of the micrographs from the light microscopy (LM), quantitative data and images from scanning electron microscopy (SEM) and energy dispersive X-ray (EDX), sub-grain size and grain structure from electron back scattered diffraction (EBSD).

Keywords: aluminium alloy, can-body stock, hot rolling, creep response, Zener-Hollomon parameter

Procedia PDF Downloads 73

Authors: Rahm Sibylle

Abstract:

The core element in most European teacher training concepts consists in practical periods where teacher students may review the chosen profession before going on to their theoretical studies. In Germany, teacher students learn in practical studies about everyday teaching and learning in schools. Teacher students appreciate opportunities to explore school practice and to feel responsible for students’ learning. In practical studies, teacher students often idealize their teacher mentors (and consequently tend to imitate their teaching style) or contrarily feel disappointed about school practice. Concepts of empowerment through practical experience in school-based academic teacher training have to be developed. Our Swiss-German research project COPRA (Coaching in practical periods; funded by the Swiss National Science Foundation (SNF) and the German Research Foundation (DFG), aims at gaining resilient results about the effectiveness of (peer) coaching in practical school periods. To explore innovative ways of accompanying novice teachers in practical periods we consider different cultures of teacher training institutions. School cultures, including teachers’ beliefs and teaching traditions involve different training cultures as starting positions for our intervention study. In our qualitative study, we describe typologies of teacher training institutions by analyzing group discussions with teacher students, mentor teachers and university lecturers concerning participation, cooperation, and relationships. In our paper, we present the design of our intervention study, our coaching concept as well as typologies of teacher training cultures. We discuss opportunities for teacher students to learn through domain-specific (peer) coaching on the background of these typologies.

Keywords: teacher training (practical periods), teacher students' coaching, training cultures (typologies), COPRA (coaching in practical periods)

Procedia PDF Downloads 228

Authors: Aulina R. Rahmi, Farid Yuristiawan, Annisa Ibifadillah, Ummu H. Amri, Hidayati Gunawan

Abstract:

Glass ionomer cement is one of the filling material that often used on the field of dentistry because it is relatively less expensive and mostly available. Restoration materials could undergo changes in their clinical properties such as changes in roughness of the restoration`s surface. An increase of surface roughness accelerates bacterial colonization and plaque maturation. In the oral cavity, GIC was exposed to various substances, such as toothpaste, an oral care product used during toothbrushing. One of the popular toothpaste is whitening toothpaste. Abrasive and chemical agents such as hydrogen peroxide in whitening toothpaste could increase the surface roughness of restorative materials. Objective: To determine the differences on the surface roughness of glass ionomer cement that was brushed with whitening and conventional toothpaste. Method: This study was done using experimental laboratory method with pre and post test design. There were 36 samples which were divided into 2 groups. The first group was brushed with whitening toothpaste and the second group was brushed with conventional toothpaste, each for 2 minutes. Surface roughness value of the specimens was measured by using Roughness Tester test. Result: The data was analyzed by using independent t-test and the result of this study showed there was a significant difference between the surface of glass ionomer cement which was brushed with whitening and conventional toothpaste (p=0,000). Conclusion: Glass ionomer cement that was brushed with whitening toothpaste produced more roughness than conventional toothpaste.

Keywords: glass ionomer cement, surface roughness, toothpaste, roughness tester

Procedia PDF Downloads 278

Authors: Headman Hebe, Arnold Taringa

Abstract:

Background of the study: The benefits derived from Environmental and Sustainability Education (ESE) go beyond obtaining knowledge about the environment and the impact of human beings on the environment. Hence, it is sensible to expose learners to various resources that could enable meaningful environment-inclined pedagogy. The schoolgrounds, where they are utilised to promote ESE, benefit holistic learner development. However, empirical evidence, globally, suggests that young children’s contact with nature is declining due to urbanization, safety concerns by parents/guardians, and greater dependency on technology. Modern children spend much time on videogames and social media with very little time in the natural environment. Furthermore, national education departments in numerous countries have made tangible efforts to embed environmental and place-based learning to their school curricula. South Africa is one of those countries whose national school education curriculum advocates for ESE in pedagogy. Nevertheless, there is paucity of research conducted in South Africa on schoolgrounds as potential enablers of ESE and tools to foster a connection between youngsters and the natural environment. Accordingly, this study was essential as it seeks to determine the extent to which environmental learning is accommodated in pedagogy. Significantly, it investigates efforts made to use schoolgrounds for pedagogical purposes to connect children with the natural environment. Therefore, this study was conducted to investigate the accessibility and use of schoolgrounds for environment-inclined pedagogy in Natural and Social Sciences in two schools located in the Mpumalanga Province of South Africa. It tries to answer the question: To what extent are schoolgrounds used to promote environmental and sustainability education in the selected schools?The sub-questions: How do teachers and learners perceive the use of schoolgrounds for environmental and sustainability education activities? How does the organization of schoolgrounds offer opportunities for environmental education activities and accessibility for learners? Research method: This qualitative–interpretive case study used purposive and convenient sampling for participant selection. Forty-six respondents: 40 learners (twenty grade 7 learners per school), 2 school principals and 4 grade 7 participated in this study. Data collection tools were observations, interviews, audio-visual recordings and questionnaires while data analysis was done thematically. Major findings: The findings of the study point to: The lack of teacher training and infrastructure in the schoolgrounds and, no administrative support. Unclear curriculum guidelines on the use of schoolgrounds for ESE. The availability various elements in the schoolgrounds that could aid ESE activities. Learners denied access to certain parts of the schoolgrounds. Lack of time and curriculum demands constrain teachers from using schoolgrounds.

Keywords: affordances, environment and sustainability education, experiential learning, schoolgrounds

Procedia PDF Downloads 46

Authors: Dinesh N. Kurup, Celine Perriera

Abstract:

The economic development of any country is based on the policies adopted by the government from time to time. If these policies are framed by the opinion of the people of the country, there is need for having strong knowledge base, right from the school level. There should be emphasis to provide in education, an ability to take informed decisions regarding socio-scientific issues. It would be better to adopt this practice in high school classrooms to build capacity among future citizens. This study is an attempt to provide a different approach of teaching and learning in classrooms at the high school level in Indian schools for providing opportunity for informed decision making regarding nuclear power use. A unit of work based on the 5E instructional model about the use of nuclear energy is used to build knowledge base and find out the effectiveness in terms of its influence for taking decisions as a future citizen. A sample of 120 students from three high schools using different curricula and teaching and learning methods were chosen for this study. This research used a design based research method. A pre and post questionnaire based on the theory of reasoned action, structured observations, focus group interviews and opportunity for decision making were used during the intervention. The data analysed qualitatively and quantitatively, and the qualitative data were coded into categories based on responses. The results of the study show that students were able to make informed decisions and could give reasons for their decisions. They were enthusiastic in formulating policy making based on their knowledge base and have strong held views and reasoning for their choice.

Keywords: informed decision making, socio-scientific issues, nuclear energy use, policy making

Procedia PDF Downloads 290

Authors: Zhaozhi Liu, Feng Xu, Junhua Xu, Xiaolong Tang, Ying Liu, Dunwen Zuo

Abstract:

Chemical vapor deposition (CVD) diamond coated cutting tool has excellent cutting performance, it is the most ideal tool for the processing of nonferrous metals and alloys, composites, nonmetallic materials and other difficult-to-machine materials efficiently and accurately. Depositing CVD diamond coating on the cemented carbide with high cobalt content can improve its toughness and strength, therefore, it is very important to research on the preparation technology and cutting properties of CVD diamond coated cemented carbide cutting tool with high cobalt content. The preparation technology of boron-doped diamond (BDD) coating has been studied and the coated drills were prepared. BDD coating were deposited on the drills by using the optimized parameters and the SEM results show that there are no cracks or collapses in the coating. Cutting tests with the prepared drills against the silumin and aluminum base printed circuit board (PCB) have been studied. The results show that the wear amount of the coated drill is small and the machined surface has a better precision. The coating does not come off during the test, which shows good adhesion and cutting performance of the drill.

Keywords: cemented carbide with high cobalt content, CVD boron-doped diamond, cutting test, drill

Procedia PDF Downloads 403

Authors: Anood Al-Shibli

Abstract:

Designing a learner corpus is not an easy task to accomplish because dealing with learners’ language has many variables which might affect the results of any study based on learners’ language production (spoken and written). Also, it is very essential to systematically design a learner corpus especially when it is aimed to be a reference to language research. Therefore, designing the Omani Learner Corpus (OLEC) has undergone many explicit and systematic considerations. These criteria can be regarded as the foundation to design any learner corpus to be exploited effectively in language use and language learning studies. Added to that, OLEC is manually error-annotated corpus. Error-annotation in learner corpora is very essential; however, it is time-consuming and prone to errors. Consequently, a navigating tool is designed to help the annotators to insert errors’ codes in order to make the error-annotation process more efficient and consistent. To assure accuracy, error annotation procedure is followed to annotate OLEC and some preliminary findings are noted. One of the main results of this procedure is creating an error-annotation system based on the Omani learners of English language production. Because OLEC is still in the first stages, the primary findings are related to only one level of proficiency and one error type which is verb related errors. It is found that Omani learners in OLEC has the tendency to have more errors in forming the verb and followed by problems in agreement of verb. Comparing the results to other error-based studies indicate that the Omani learners tend to have basic verb errors which can found in lower-level of proficiency. To this end, it is essential to admit that examining learners’ errors can give insights to language acquisition and language learning and most errors do not happen randomly but they occur systematically among language learners.

Keywords: error-annotation system, error-annotation manual, learner corpora, verbs related errors

Procedia PDF Downloads 126

Authors: Lourdes Hanna, Edward Poluyi, Chibuikem Ikwuegbuenyi, Eghosa Morgan, Grace Imaguezegie

Abstract:

Background: Degeneration of the central nervous system (CNS), also known as neurodegeneration, describes an age-associated progressive loss of the structure and function of neuronal materials, leading to functional and mental impairments. Main body: Neuroinflammation contributes to the continuous worsening of neurodegenerative states which are characterised by functional and mental impairments due to the progressive loss of the structure and function of neu-ronal materials. Some of the most common neurodegenerative diseases include Alzheimer’s disease (AD), Parkinson’s disease (PD) and amyotrophic lateral sclerosis (ALS). Whilst neuroinflammation is a key contributor to the progression of such disease states, it is not the single cause as there are multiple factors which contribute. Theoretically, non-steroidal anti-inflammatory drugs (NSAIDs) have potential to target neuroinflammation to reduce the severity of disease states. Whilst some animal models investigating the effects of NSAIDs on the risk of neurodegenerative diseases have shown a beneficial effect, this is not the same finding. Conclusion: Further investigation using more advanced research methods is required to better understand neuroinflammatory pathways and understand if there is still a potential window for NSAID efficacy.

Keywords: intervention, central nervous system, neurodegeneration, neuroinflammation

Procedia PDF Downloads 64

Authors: Martha Karunakar

Abstract:

There exists a wide divide between the urban and the rural students in a vast country like India. This dichotomy is seen in the resources available to them, like the learning facilities, the infra-structure, the learning ambience and meeting of their basic needs of food, clothing and shelter. This paper discusses the effect of English language teaching as a Bridge course on a select batch of rural students at an Engineering college in Chennai, one of the four Metros of India. The study aims to understand how the teacher input and the teacher- peer-student interaction facilitates the acquisition of the basic structures of the English language to a group that is minimally exposed to the language. The objective in conducting the Bridge Course is to integrate these rural students into the mainstream and empower them in terms of English speaking ability; to enable them to comprehend their respective engineering classes where the medium of instruction is English and also to be able to interact with their urban peers. This program is conducted prior to the start of a regular academic session to equip them face the rigors of engineering education. The study is placed within the framework of Interaction theory in second language acquisition. The study evaluates the impact of linking theory and practice by implementing meaningful interaction not only within classrooms but also in the common areas. By providing intensive comprehensible input, it is anticipated that participant’s level of English language improves. The teaching methods and classroom activities included individual and group participation, encompassing all the four skills of listening, speaking, reading and writing (LSRW). The diagnostic tests that were administered before the commencement of the course and the exit test after the completion were used to record the impact of the training.

Keywords: comprehensible input, interaction, rural students, teaching English

Procedia PDF Downloads 365

Authors: Biki Sarmah, Priyanko Raj Mudiar

Abstract:

In the modern world of remotely interactive virtual reality-based learning and teaching, including professional skill-building training and acquisition practices, as well as data acquisition and robotic systems, the revolutionary application or implementation of field-programmable neurostimulator aids and first-hand interactive sensitisation techniques into 3D holographic audio-visual platforms have been a coveted dream of many scholars, professionals, scientists, and students. Integration of 'kinaesthetic vibrotactile haptic perception' along with an actuated step magnitude contact profiloscopy in augmented reality-based learning platforms and professional training can be implemented by using an extremely calculated and well-coordinated image telemetry including remote data mining and control technique. A real-time, computer-aided (PLC-SCADA) field calibration based algorithm must be designed for the purpose. But most importantly, in order to actually realise, as well as to 'interact' with some 3D holographic models displayed over a remote screen using remote laser image telemetry and control, all spatio-physical parameters like cardinal alignment, gyroscopic compensation, as well as surface profile and thermal compositions, must be implemented using zero-order type 1 actuators (or transducers) because they provide zero hystereses, zero backlashes, low deadtime as well as providing a linear, absolutely controllable, intrinsically observable and smooth performance with the least amount of error compensation while ensuring the best ergonomic comfort ever possible for the users.

Keywords: haptic feedback, kinaesthetic vibrotactile 3D design, medical simulation training, piezo diaphragm based actuator

Procedia PDF Downloads 143

Authors: Salisu Dahiru, Jibrin M. Kaura, Abubakar I. Jumare, Sulaiman M. Mahmood

Abstract:

Reclaimed asphalt, used automobile tires and rice husk, were regarded as waste. These materials could be used in construction of new roads and for roads rehabilitation. Investigation into the production of a Green Hot Mixed Asphalt (GHMA) pavement using Reclaimed Asphalt Pavement (RAP) as partial replacement for coarse aggregate, Crumb Rubber (CR) from waste automobile tires as modifier for bitumen binder and Rice Husk Ash (RHA) as partial replacement of ordinary portland cement (OPC) filler, for roads construction and rehabilitation was presented. 30% Reclaimed asphalt of total aggregate, 15% Crumb Rubber of total binder content, 5% Rice Husk Ash of total mix, and 5.2% Crumb Rubber Modified Bitumen content were recommended for optimum performance. Loss of marshal stability was investigated on mix with the recommended optimum CRMB. The mix revealed good performance with only about 13% loss of stability after 24 hours of immersion in hot water bath, as against about 24% marshal stability lost reported in previous studies for conventional Hot Mixed Asphalt (HMA).

Keywords: rice husk, reclaimed asphalt, filler, crumb rubber, bitumen content green hot mix asphalt

Procedia PDF Downloads 318

Authors: Ivan Kuzio

Abstract:

The GIZ/TTC project is the first of its kind in the Middle East, which allows the development of a teaching training programme to degree level based on modern methodologies. The graduates from this college are part of the Saudization programme and will, over the next four years be part of and eventually run the new Colleges of Excellence. The new Colleges of Excellence are being developed to create a local vocationally trained workforce and will run initially alongside the current Colleges of Technology.

Keywords: blended learning, pedagogy, training, key competencies, social skills, cognitive development

Procedia PDF Downloads 296