Search results for: epidemiological study
13977 Use of Chemical Extractions to Estimate the Metals Availability in Bricks Made of Dredged Sediments
Authors: Fabienne Baraud, Lydia Leleyter, Sandra Poree, Melanie Lemoine
Abstract:
SEDIBRIC (valorization de SEDIments en BRIQues et tuiles) is a French project that aims to replace a part of natural clays with dredged sediments in the preparation of fired bricks in order to propose an alternative solution for the management of harbor dredged sediments. The feasibility of such re-use is explored from a technical, economic, and environmental point of view. The present study focuses on the potential environmental impact of various chemical elements (Al, Ca, Cd, Co, Cr, Cu, Fe, Ni, Mg, Mn, Pb, Ti, and Zn) that are initially present in the dredged sediments. The total content (after acid digestion) and the environmental availability (estimated by single extractions with various extractants) of these elements are determined in the raw sediments and in the obtained fired bricks. The possible influence of some steps of the manufacturing process (sediment pre-treatment, firing) is also explored. The first results show that the pre-treatment step, which uses tap water to desalinate the raw sediment, does not influence the environmental availability of the studied elements. However, the firing process, performed at 900°C, can affect the amount of some elements detected in the bricks, as well as their environmental availability. We note that for Cr, or Ni, the HCl or EDTA availability was increased in the brick (compared to the availability in the raw sediment). For Cd, Cu, Pb, and Zn, the HCl and EDTA availability was reduced in the bricks, meaning that these elements were stabilized within the bricks.Keywords: bricks, chemical extraction, metals, sediment
Procedia PDF Downloads 14313976 Estimation of Opc, Fly Ash and Slag Contents in Blended and Composite Cements by Selective Dissolution Method
Authors: Suresh Palla
Abstract:
This research paper presents the results of the study on the estimation of fly ash, slag and cement contents in blended and composite cements by novel selective dissolution method. Types of cement samples investigated include OPC with fly ash as performance improver, OPC with slag as performance improver, PPC, PSC and Composite cement confirming to respective Indian Standards. Slag and OPC contents in PSC were estimated by selectively dissolving OPC in stage 1 and selectively dissolving slag in stage 2. In the case of composite cement sample, the percentage of cement, slag and fly ash were estimated systematically by selective dissolution of cement, slag and fly ash in three stages. In the first stage, cement dissolved and separated by leaving the residue of slag and fly ash, designated as R1. The second stage involves gravimetric estimation of fractions of OPC, residue and selective dissolution of fly ash and slag contents. Fly ash content, R2 was estimated through gravimetric analysis. Thereafter, the difference between the R1 and R2 is considered as slag content. The obtained results of cement, fly ash and slag using selective dissolution method showed 10% of standard deviation with the corresponding percentage of respective constituents. The results suggest that this novel selective dissolution method can be successfully used for estimation of OPC and SCMs contents in different types of cements.Keywords: selective dissolution method , fly ash, ggbfs slag, edta
Procedia PDF Downloads 14913975 Synthesis and Characterization of Poly (N-(Pyridin-2-Ylmethylidene)Pyridin-2-Amine: Thermal and Conductivity Properties
Authors: Nuray Yılmaz Baran
Abstract:
The conjugated Schiff base polymers which are also called as polyazomethines are promising materials for various applications due to their good thermal resistance semiconductive, liquid crystal, fiber forming, nonlinear optical outstanding photo- and electroluminescence and antimicrobial properties. In recent years, polyazomethines have attracted intense attention of researchers especially due to optoelectronic properties which have made its usage possible in organic light emitting diodes (OLEDs), solar cells (SCs), organic field effect transistors (OFETs), and photorefractive holographic materials (PRHMs). In this study, N-(pyridin-2-ylmethylidene)pyridin-2-amine Schiff base was synthesized from condensation reaction of 2-aminopyridine with 2-pyridine carbaldehyde. Polymerization of Schiff base was achieved by polycondensation reaction using NaOCl oxidant in methanol medium at various time and temperatures. The synthesized Schiff base monomer and polymer (Poly(N-(pyridin-2-ylmethylidene)pyridin-2-amine)) was characterized by UV-vis, FT-IR, 1H-NMR, XRD techniques. Molecular weight distribution and the surface morphology of the polymer was determined by GPC and SEM-EDAX techniques. Thermal behaviour of the monomer and polymer was investigated by TG/DTG, DTA and DSC techniques.Keywords: polyazomethines, polycondensation reaction, Schiff base polymers, thermal stability
Procedia PDF Downloads 22513974 Ubuntu: A Holistic Social Framework for Preserving Ecosystem Amidst the Climate Change Challenges
Authors: Gabriel Sunday Ayayia
Abstract:
The paper argues that Ubuntu, as a philosophy that emphasizes the interconnectedness of all living things and importance of community and mutual support, can be used as a social framework to address the problems of climate change and promote environmental sustainability. The research demonstrate that Ubuntu is an ideological concept that encourages collective action on climate change, with the emphasis on individual and collective commitment to taking concrete action to address the problems of climate change. The paper shows that Ubuntu can be employed as a social tool that would enhance the cultivation of shared identity and promote the sense of shared response responsibility to develop the resilience to cope with climate change. Using qualitative and quantitative methodologies, the study establishes the imperativeness of mutual support and cooperation through the lens of Ubuntu as a human-centered scalable response to the debacle of climate change. It recommends that we can build a society that values the environment and promotes sustainable practices by encouraging community involvement in sustainable initiatives by integrating Ubuntu-based principles to our decision-making processes, collaboration, leadership, human agency and governance.Keywords: ubuntu, climate change, humanity, collective actions, community-based
Procedia PDF Downloads 17913973 Optimizing of the Micro EDM Parameters in Drilling of Titanium Ti-6Al-4V Alloy for Higher Machining Accuracy-Fuzzy Modelling
Authors: Ahmed A. D. Sarhan, Mum Wai Yip, M. Sayuti, Lim Siew Fen
Abstract:
Ti6Al4V alloy is highly used in the automotive and aerospace industry due to its good machining characteristics. Micro EDM drilling is commonly used to drill micro hole on extremely hard material with very high depth to diameter ratio. In this study, the parameters of micro-electrical discharge machining (EDM) in drilling of Ti6Al4V alloy is optimized for higher machining accuracy with less hole-dilation and hole taper ratio. The micro-EDM machining parameters includes, peak current and pulse on time. Fuzzy analysis was developed to evaluate the machining accuracy. The analysis shows that hole-dilation and hole-taper ratio are increased with the increasing of peak current and pulse on time. However, the surface quality deteriorates as the peak current and pulse on time increase. The combination that gives the optimum result for hole dilation is medium peak current and short pulse on time. Meanwhile, the optimum result for hole taper ratio is low peak current and short pulse on time.Keywords: Micro EDM, Ti-6Al-4V alloy, fuzzy logic based analysis, optimization, machining accuracy
Procedia PDF Downloads 48913972 A Deep-Learning Based Prediction of Pancreatic Adenocarcinoma with Electronic Health Records from the State of Maine
Authors: Xiaodong Li, Peng Gao, Chao-Jung Huang, Shiying Hao, Xuefeng B. Ling, Yongxia Han, Yaqi Zhang, Le Zheng, Chengyin Ye, Modi Liu, Minjie Xia, Changlin Fu, Bo Jin, Karl G. Sylvester, Eric Widen
Abstract:
Predicting the risk of Pancreatic Adenocarcinoma (PA) in advance can benefit the quality of care and potentially reduce population mortality and morbidity. The aim of this study was to develop and prospectively validate a risk prediction model to identify patients at risk of new incident PA as early as 3 months before the onset of PA in a statewide, general population in Maine. The PA prediction model was developed using Deep Neural Networks, a deep learning algorithm, with a 2-year electronic-health-record (EHR) cohort. Prospective results showed that our model identified 54.35% of all inpatient episodes of PA, and 91.20% of all PA that required subsequent chemoradiotherapy, with a lead-time of up to 3 months and a true alert of 67.62%. The risk assessment tool has attained an improved discriminative ability. It can be immediately deployed to the health system to provide automatic early warnings to adults at risk of PA. It has potential to identify personalized risk factors to facilitate customized PA interventions.Keywords: cancer prediction, deep learning, electronic health records, pancreatic adenocarcinoma
Procedia PDF Downloads 14913971 Minimum-Fuel Optimal Trajectory for Reusable First-Stage Rocket Landing Using Particle Swarm Optimization
Authors: Kevin Spencer G. Anglim, Zhenyu Zhang, Qingbin Gao
Abstract:
Reusable launch vehicles (RLVs) present a more environmentally-friendly approach to accessing space when compared to traditional launch vehicles that are discarded after each flight. This paper studies the recyclable nature of RLVs by presenting a solution method for determining minimum-fuel optimal trajectories using principles from optimal control theory and particle swarm optimization (PSO). This problem is formulated as a minimum-landing error powered descent problem where it is desired to move the RLV from a fixed set of initial conditions to three different sets of terminal conditions. However, unlike other powered descent studies, this paper considers the highly nonlinear effects caused by atmospheric drag, which are often ignored for studies on the Moon or on Mars. Rather than optimizing the controls directly, the throttle control is assumed to be bang-off-bang with a predetermined thrust direction for each phase of flight. The PSO method is verified in a one-dimensional comparison study, and it is then applied to the two-dimensional cases, the results of which are illustrated.Keywords: minimum-fuel optimal trajectory, particle swarm optimization, reusable rocket, SpaceX
Procedia PDF Downloads 27013970 Dilution Effect in Islamic Finance: The Case of Convertible Sukuk
Authors: Mahfoud Djebbar
Abstract:
Stock dilution is a financial phenomenon resulting from the issue of additional shares by a company, or when holders convert their convertibles into new shares (capital increase). This issue and/or conversion enlarge the company’s share base that will result in marginal dilution (loss) for existing shareholders, and a benefit to new ones. Dilution issues have already been addressed in mainstream finance, particularly as far as information disclosure is concerned. However, in Islamic finance, stock dilution problems have not been deeply studied and the subject has not received sufficient attention from shariah-compatible firms, investors, and scholars. In this regard, this paper emphasises the forms, the effects of capital dilution on current shareholders as well as the ways and techniques of compensating them. And since the research in this field, in its Islamic perspective, is still in its infancy, the paper tries to analyse the phenomenon theoretically in detail using numerical examples, and expose some case studies of Shariah-compliant issuers of convertible Sukuk and how they compensate their existing shareholders. Finally, this study shows that the Sukuk issuers compensate old shareholders using the right of shuf’ah as a well known and practiced pre-emptive right in Islamic transactions centuries ago, as well as the ways conventional bond issuers use.Keywords: compensating shareholders, convertible Sukuk, Islamic financial innovation, Shuf’ah
Procedia PDF Downloads 33013969 A Quantitative Case Study Analysis of Store Format Contributors to U.S. County Obesity Prevalence in Virginia
Authors: Bailey Houghtaling, Sarah Misyak
Abstract:
Food access; the availability, affordability, convenience, and desirability of food and beverage products within communities, is influential on consumers’ purchasing and consumption decisions. These variables may contribute to lower dietary quality scores and a higher obesity prevalence documented among rural and disadvantaged populations in the United States (U.S.). Current research assessing linkages between food access and obesity outcomes has primarily focused on distance to a traditional grocery/supermarket store as a measure of optimality. However, low-income consumers especially, including U.S. Department of Agriculture’s Supplemental Nutrition Assistance Program (SNAP) participants, seem to utilize non-traditional food store formats with greater frequency for household dietary needs. Non-traditional formats have been associated with less nutritious food and beverage options and consumer purchases that are high in saturated fats, added sugars, and sodium. Authors’ formative research indicated differences by U.S. region and rurality in the distribution of traditional and non-traditional SNAP-authorized food store formats. Therefore, using Virginia as a case study, the purpose of this research was to determine if a relationship between store format, rurality, and obesity exists. This research applied SNAP-authorized food store data (food access points for SNAP as well as non-SNAP consumers) and obesity prevalence data by Virginia county using publicly available databases: (1) SNAP Retailer Locator, and; (2) U.S. County Health Rankings. The alpha level was set a priori at 0.05. All Virginia SNAP-authorized stores (n=6,461) were coded by format – grocery, drug, mass merchandiser, club, convenience, dollar, supercenter, specialty, farmers market, independent grocer, and non-food store. Simple linear regression was applied primarily to assess the relationship between store format and obesity. Thereafter, multiple variables were added to the regression to account for potential moderating relationships (e.g., county income, rurality). Convenience, dollar, non-food or restaurant, mass merchandiser, farmers market, and independent grocer formats were significantly, positively related to obesity prevalence. Upon controlling for urban-rural status and income, results indicated the following formats to be significantly related to county obesity prevalence with a small, positive effect: convenience (p=0.010), accounting for 0.3% of the variance in obesity prevalence; dollar (p=0.005; 0.5% of the variance), and; non-food (p=0.030; 1.3% of the variance) formats. These results align with current literature on consumer behavior at non-traditional formats. For example, consumers’ food and beverage purchases at convenience and dollar stores are documented to be high in saturated fats, added sugars, and sodium. Further, non-food stores (i.e., quick-serve restaurants) often contribute to a large portion of U.S. consumers’ dietary intake and thus poor dietary quality scores. Current food access research investigates grocery/supermarket access and obesity outcomes. These results suggest more research is needed that focuses on non-traditional food store formats. Nutrition interventions within convenience, dollar, and non-food stores, for example, that aim to enhance not only healthy food access but the affordability, convenience, and desirability of nutritious food and beverage options may impact obesity rates in Virginia. More research is warranted utilizing the presented investigative framework in other U.S. and global regions to explore the role and the potential of non-traditional food store formats to prevent and reduce obesity.Keywords: food access, food store format, non-traditional food stores, obesity prevalence
Procedia PDF Downloads 13013968 Towards Understanding Arab Consumer’s Response to Foreign Marketing: An Empirical Evidence from Libya
Authors: Izzudin Busnaina
Abstract:
An important question for marketers in the international arena is whether the consumer’s responses (i.e., sentiment and behavioral aspects) toward the global marketing programs in developing countries depend on culture. In a study representing a large sample of consumers and four different home appliances country-of-origin global operators in Libya, the author explores the potential role of culture on Arab consumers' responses toward foreign marketing programs. Results indicate that although the foreign companies have a tendency to adopted standardization perspective, this does not impact on consumers’ responses in a single cultural context toward marketing. The findings reveal that buying behavior was more a function of individual difference than of national cultural context. Further, the results suggest that for mainstream home appliances, segmenting on the basis of nationality is probably unnecessary and that a standardized approach would likely be successful across an increasingly relevant Arab world; and that continuing perceptions of Arab insularity are likely to be misplaced. Faced with the effectiveness of globally efficient marketing programs, local manufacturers would need to work hard to identify particular niche segments where a culturally-specific appeal might be more successful.Keywords: arab world, buyer’s characteristics, consumer behavior, home appliances, marketing program
Procedia PDF Downloads 39013967 Titania Assisted Metal-Organic Framework Matrix for Elevated Hydrogen Generation Combined with the Production of Graphene Sheets through Water-Splitting Process
Authors: Heba M. Gobara, Ahmed A. M. El-Naggar, Rasha S. El-Sayed, Amal A. AlKahlawy
Abstract:
In this study, metal organic framework (Cr-MIL-101) and TiO₂ nanoparticles were utilized as two semiconductors for water splitting process. The coupling of both semiconductors in order to improve the photocatalytic reactivity for the hydrogen production in presence of methanol as a hole scavenger under visible light (sunlight) has been performed. The forementioned semiconductors and the collected samples after water splitting application are characterized by several techniques viz., XRD, N₂ adsorption-desorption, TEM, ED, EDX, Raman spectroscopy and the total content of carbon. The results revealed an efficient yield of H₂ production with maximum purity 99.3% with the in-situ formation of graphene oxide nanosheets and multiwalled carbon nanotubes coated over the surface of the physically mixed Cr-MIL-101–TiO₂ system. The amount of H₂ gas produced was stored when using Cr-MIL-101 catalyst individually. The obtained data in this work provides promising candidate materials for pure hydrogen production as a clean fuel acquired from the water splitting process. In addition, the in-situ production of graphene nanosheets and carbon nanotubes is counted as promising advances for the presented process.Keywords: hydrogen production, water splitting, photocatalysts, Graphene
Procedia PDF Downloads 18113966 Development of EREC IF Model to Increase Critical Thinking and Creativity Skills of Undergraduate Nursing Students
Authors: Kamolrat Turner, Boontuan Wattanakul
Abstract:
Critical thinking and creativity are prerequisite skills for working professionals in the 21st century. A survey conducted in 2014 at the Boromarajonani College of Nursing, Chon Buri, Thailand, revealed that these skills within students across all academic years was at a low to moderate level. An action research study was conducted to develop the EREC IF Model, a framework which includes the concepts of experience, reflection, engagement, culture and language, ICT, and flexibility and fun, to guide pedagogic activities for 75 sophomores of the undergraduate nursing science program at the college. The model was applied to all professional nursing courses. Prior to implementation, workshops were held to prepare lecturers and students. Both lecturers and students initially expressed their discomfort and pointed to the difficulties with the model. However, later they felt more comfortable, and by the end of the project they expressed their understanding and appreciation of the model. A survey conducted four and eight months after implementation found that the critical thinking and creativity skills of the sophomores were significantly higher than those recorded in the pretest. It could be concluded that the EREC IF model is efficient for fostering critical thinking and creativity skills in the undergraduate nursing science program. This model should be used for other levels of students.Keywords: critical thinking, creativity, undergraduate nursing students, EREC IF model
Procedia PDF Downloads 31813965 Protein Derived Biodegradable Food Packaging Material from Poultry By-Product
Authors: Muhammad Zubair, Aman Ullah, Jianping Wu
Abstract:
During the last decades, petroleum derived synthetic polymers like polyethylene terephthalate, polyvinylchloride, polyethylene, polypropylene and polystyrene has extensively been used in the field of food packaging and mostly are non-degradable. Biopolymers are a good fit for single-use or short-lived products such as food packaging. Spent hens, a poultry by-product which is of little economic value and their disposal are environmentally harmful. Through current study, we have explored the possibility to transform proteins from spent fowl into green food packaging material. Proteins from spent fowl were extracted within 1 hour using pH shift method with recovery of about 74%. Different plasticizers were tried like glycerol, sorbitol, glutaraldehyde, 1,2 ethylene glycol and 1,2 butanediol. Glycerol was the best plasticizer among all these plasticizers. A naturally occurring and non-toxic cross-linking agent, chitosan, was used to form the chitosan/glycerol/protein blend by casting and compression molding techniques. The mechanical properties were characterized using tensile strength analyzer. The nano-reinforcements with homogeneous dispersion of nanoparticles lead to improved physical properties suggesting that these materials have great potential for food packaging applications.Keywords: differential scanning calorimetry, dynamic mechanical analysis, scanning electron microscopy, spent hen
Procedia PDF Downloads 27113964 The Regional Expression of New Rural Dwellings Design in Linhai, Zhejiang: A Case of New Rural Dwellings Design in Badie Village
Authors: Fan Zhang
Abstract:
In the process of urbanization in China, the new rural construction is in the ascendant, which is becoming more and more popular. Under the driving effect of rural urbanization, the house pattern and tectonic methods of traditional vernacular houses have shown great differences from the family structure and values of contemporary peasant families. Therefore, it is particularly important to find a prototype, form and strategy, to make a balance between the traditional memory and modern functional requirements. In order for research to combine the regional culture with modern life, under the situation of the current batch production of new rural residence, Badie village, in Linhai, Zhejiang province, is taken as the case. This paper aims to put forward a prototype which can not only meet the demand of modern life but also ensure the continuation of traditional culture and historical context for the new rural dwellings design. This research not only helps to extend the local context in the construction of the new site but also contributes to the fusion of old and new rural dwellings in the old site construction. Through the study and research of this case, the research methodology and results can be drawn as reference for the new rural construction in other areas.Keywords: badie village, design strategy, new rural dwellings, regional context, regional expression
Procedia PDF Downloads 20213963 Determination of the Optimal DG PV Interconnection Location Using Losses and Voltage Regulation as Assessment Indicators Case Study: ECG 33 kV Sub-Transmission Network
Authors: Ekow A. Kwofie, Emmanuel K. Anto, Godfred Mensah
Abstract:
In this paper, CYME Distribution software has been used to assess the impacts of solar Photovoltaic (PV) distributed generation (DG) plant on the Electricity Company of Ghana (ECG) 33 kV sub-transmission network at different PV penetration levels. As ECG begins to encourage DG PV interconnections within its network, there has been the need to assess the impacts on the sub-transmission losses and voltage contribution. In Tema, a city in Accra - Ghana, ECG has a 33 kV sub-transmission network made up of 20 No. 33 kV buses that was modeled. Three different locations were chosen: The source bus, a bus along the sub-transmission radial network and a bus at the tail end to determine the optimal location for DG PV interconnection. The optimal location was determined based on sub-transmission technical losses and voltage impact. PV capacities at different penetration levels were modeled at each location and simulations performed to determine the optimal PV penetration level. Interconnection at a bus along (or in the middle of) the sub-transmission network offered the highest benefits at an optimal PV penetration level of 80%. At that location, the maximum voltage improvement of 0.789% on the neighboring 33 kV buses and maximum loss reduction of 6.033% over the base case scenario were recorded. Hence, the optimal location for DG PV integration within the 33 kV sub-transmission utility network is at a bus along the sub-transmission radial network.Keywords: distributed generation photovoltaic (DG PV), optimal location, penetration level, sub–transmission network
Procedia PDF Downloads 33913962 Advanced Seismic Retrofit of a School Building by a DFP Base Isolation Solution
Authors: Stefano Sorace, Gloria Terenzi
Abstract:
The study of a base isolation seismic retrofit solution for a reinforced concrete school building is presented in this paper. The building was assumed as a benchmark structure for a Research Project financed by the Italian Department of Civil Protection, and is representative of several similar public edifices designed with earlier Technical Standards editions, in Italy as well as in other earthquake-prone European countries. The structural characteristics of the building, and a synthesis of the investigation campaigns developed on it, are initially presented. The mechanical parameters, dimensions, locations and installation details of the base isolation system, incorporating double friction pendulum sliding bearings as protective devices, are then illustrated, along with the performance assessment analyses carried out in original and rehabilitated conditions according to a full non-linear dynamic approach. The results of the analyses show a remarkable enhancement of the seismic response capacities of the structure in base-isolated configuration. This allows reaching the high performance levels postulated in the rehabilitation design with notably lower costs and architectural intrusion as compared to traditional retrofit interventions designed for the same objectives.Keywords: seismic retrofit, seismic assessment, r/c structures, school buildings, base isolation
Procedia PDF Downloads 25913961 The Effect Of Flights Schedules On Airline Choice Model For International Round-Trip Flights
Authors: Claudia Munoz, Henry Laniado
Abstract:
In this research, the impact of outbound and return flight schedule preferences on airline choice for international trips is quantified. Several studies have used airline choice data to identify preferences and trade-offs of different air carrier service attributes, such as travel time, fare and frequencies. However, estimation of the effect return flight schedules have on airline choice for an international round-trip flight has not yet been studied in detail. The multinomial logit model found shows that airfare, travel time, arrival preference schedule in the outward journey, departure preference in the return journey and the schedule combination of round-trip flights are significantly affecting passenger choice behavior in international round-trip flights. it results indicated that return flight schedule preference plays a substantial role in air carrier choice and has a similar effect to outbound flight schedule preference. Thus, this study provides an analytical tool designed to provide a better understanding of international round-trip flight demand determinants and support carrier decisions.Keywords: flight schedule, airline choice, return flight, passenger choice behavior
Procedia PDF Downloads 513960 Effect of Building Construction Sizes on Project Delivery Methods in Nigeria
Authors: Nuruddeen Usman, Mohammad Sani
Abstract:
The performance of project delivery methods has been an issue of concern to various stakeholders in the construction industry. The contracting system of project delivery is the traditional system used in the delivery of most public projects in Nigeria. The direct labor system is used most times as an alternative to the traditional system. There were so many complain about the performance of contracting system and the suitability of direct labor as an alternative to the delivery of public projects. Therefore, this paper is aimed at investigating the effect of project size on the project delivery methods in the completed public buildings. Questionnaires were self-administered to managerial staff in the study area and analyzed using descriptive statistics. The findings reveals that contracting system was choosing for large size building construction project delivery with higher frequency (F) of 40 (76.9%) against direct labor with 12 (23.1%). While the small size project, the result revealed a frequency (F) of 26 (50%) for contracting system and direct labor system respectively. Base on the research findings, the contracting system, was recommended for all sizes of building construction project delivery while direct labor system can only use as an alternative for small size building construction projects delivery.Keywords: construction size, contracting system, direct labour, effect
Procedia PDF Downloads 44913959 The Evaluation of Costs and Greenhouse Gas Reduction by Using Technologies for Energy from Sewage Sludge
Authors: Futoshi Kakuta, Takashi Ishida
Abstract:
Sewage sludge is a biomass resource that can create a solid fuel and electricity. Utilizing sewage sludge as a renewable energy can contribute to the reduction of greenhouse gasses. In Japan, 'The National Plan for the Promotion of Biomass Utilization' and 'The Priority Plan for Social Infrastructure Development' were approved at cabinet meetings in December 2010 and August 2012, respectively, to promote the energy utilization of sewage sludge. This study investigated costs and greenhouse gas emission in different sewage sludge treatments with technologies for energy from sewage sludge. Costs were estimated on capital costs and O&M costs including energy consumption of solid fuel plants and biogas power generation plants for sewage sludge. Results showed that cost of sludge digestion treatment with solid fuel technologies was 8% lower than landfill disposal. Greenhouse gas emission of sludge digestion treatment with solid fuel technologies was also 6,390t as CO2 smaller than landfill disposal. Biogas power generation reduced the electricity of a wastewater treatment plant by 30% and the cost by 5%.Keywords: global warming countermeasure, energy technology, solid fuel production, biogas
Procedia PDF Downloads 37713958 Auto-Tuning of CNC Parameters According to the Machining Mode Selection
Authors: Jenq-Shyong Chen, Ben-Fong Yu
Abstract:
CNC(computer numerical control) machining centers have been widely used for machining different metal components for various industries. For a specific CNC machine, its everyday job is assigned to cut different products with quite different attributes such as material type, workpiece weight, geometry, tooling, and cutting conditions. Theoretically, the dynamic characteristics of the CNC machine should be properly tuned match each machining job in order to get the optimal machining performance. However, most of the CNC machines are set with only a standard set of CNC parameters. In this study, we have developed an auto-tuning system which can automatically change the CNC parameters and in hence change the machine dynamic characteristics according to the selection of machining modes which are set by the mixed combination of three machine performance indexes: the HO (high surface quality) index, HP (high precision) index and HS (high speed) index. The acceleration, jerk, corner error tolerance, oscillation and dynamic bandwidth of machine’s feed axes have been changed according to the selection of the machine performance indexes. The proposed auto-tuning system of the CNC parameters has been implemented on a PC-based CNC controller and a three-axis machining center. The measured experimental result have shown the promising of our proposed auto-tuning system.Keywords: auto-tuning, CNC parameters, machining mode, high speed, high accuracy, high surface quality
Procedia PDF Downloads 37313957 Heat Transfer Analysis of Corrugated Plate Heat Exchanger
Authors: Ketankumar Gandabhai Patel, Jalpit Balvantkumar Prajapati
Abstract:
Plate type heat exchangers has many thin plates that are slightly apart and have very large surface areas and fluid flow passages that are good for heat transfer. This can be a more effective heat exchanger than the tube or shell heat exchanger due to advances in brazing and gasket technology that have made this plate exchanger more practical. Plate type heat exchangers are most widely used in food processing industries and dairy industries. Mostly fouling occurs in plate type heat exchanger due to deposits create an insulating layer over the surface of the heat exchanger, that decreases the heat transfer between fluids and increases the pressure drop. The pressure drop increases as a result of the narrowing of the flow area, which increases the gap velocity. Therefore, the thermal performance of the heat exchanger decreases with time, resulting in an undersized heat exchanger and causing the process efficiency to be reduced. Heat exchangers are often over sized by 70 to 80%, of which 30 % to 50% is assigned to fouling. The fouling can be reduced by varying some geometric parameters and flow parameters. Based on the study, a correlation will estimate for Nusselt number as a function of Reynolds number, Prandtl number and chevron angle.Keywords: heat transfer coefficient, single phase flow, mass flow rate, pressure drop
Procedia PDF Downloads 30313956 A Script for Presentation to the Management of a Teaching Hospital on DXplain Clinical Decision Support System
Authors: Jacob Nortey
Abstract:
Introduction: In recent years, there has been an enormous success in discoveries of scientific knowledge in medicine coupled with the advancement of technology. Despite all these successes, diagnoses and treatment of diseases have become complex. According to the Ibero – American Study of Adverse Effects (IBEAS), about 10% of hospital patients suffer from secondary damage during the care process, and approximately 2% die from this process. Many clinical decision support systems have been developed to help mitigate some healthcare medical errors. Method: Relevant databases were searched, including ones that were peculiar to the clinical decision support system (that is, using google scholar, Pub Med and general google searches). The articles were then screened for a comprehensive overview of the functionality, consultative style and statistical usage of Dxplain Clinical decision support systems. Results: Inferences drawn from the articles showed high usage of Dxplain clinical decision support system for problem-based learning among students in developed countries as against little or no usage among students in Low – and Middle – income Countries. The results also indicated high usage among general practitioners. Conclusion: Despite the challenges Dxplain presents, the benefits of its usage to clinicians and students are enormous.Keywords: dxplain, clinical decision support sytem, diagnosis, support systems
Procedia PDF Downloads 7413955 Correlation and Prediction of Biodiesel Density
Authors: Nieves M. C. Talavera-Prieto, Abel G. M. Ferreira, António T. G. Portugal, Rui J. Moreira, Jaime B. Santos
Abstract:
The knowledge of biodiesel density over large ranges of temperature and pressure is important for predicting the behavior of fuel injection and combustion systems in diesel engines, and for the optimization of such systems. In this study, cottonseed oil was transesterified into biodiesel and its density was measured at temperatures between 288 K and 358 K and pressures between 0.1 MPa and 30 MPa, with expanded uncertainty estimated as ±1.6 kg.m^-3. Experimental pressure-volume-temperature (pVT) cottonseed data was used along with literature data relative to other 18 biodiesels, in order to build a database used to test the correlation of density with temperarure and pressure using the Goharshadi–Morsali–Abbaspour equation of state (GMA EoS). To our knowledge, this is the first that density measurements are presented for cottonseed biodiesel under such high pressures, and the GMA EoS used to model biodiesel density. The new tested EoS allowed correlations within 0.2 kg•m-3 corresponding to average relative deviations within 0.02%. The built database was used to develop and test a new full predictive model derived from the observed linear relation between density and degree of unsaturation (DU), which depended from biodiesel FAMEs profile. The average density deviation of this method was only about 3 kg.m-3 within the temperature and pressure limits of application. These results represent appreciable improvements in the context of density prediction at high pressure when compared with other equations of state.Keywords: biodiesel density, correlation, equation of state, prediction
Procedia PDF Downloads 60413954 Rural Tourism as a Development Strategy in Communities of the Sierra Gorda of Querétaro
Authors: Eduardo Ruiz-Corzo, Luis Rodrigo Valencia Perez, Jorge Francisco Barragan Lopez
Abstract:
The article shows the pressing conditions of marginalization prevailing in the Sierra Gorda, in the northern state of Queretaro, so it is essential to identify business options that generate a complementary source of income in a sustainable manner, in accordance with the fact that the area is a Biosphere Reserve by UNESCO. In this sense, the study identifies the enormous scenic richness of the area, the growing demand for leisure activities of the urban centers and the multifunctionality that adds, in a complementary way, the traditional activities that up to now have achieved the quality of life levels. From the application of the 43 interviews and 183 surveys, confirms the fact that the post-visit perception exceeds the expectations of the visitors emerges and affirms that the image that has been projected is attractive and timely. In order to understand how the current model of tourism promoted in the region is working, there is a need to evaluate it in a theoretical-methodological framework considering sustainable development assumptions. In order to determine the degree of contribution to business development, strengthening of social capital, and enjoyment and appreciation of cultural and natural heritage in the region.Keywords: marginalization, rural tourism, multifunctionality, sustainability, revenue
Procedia PDF Downloads 14013953 Molecular Evidence for Three Species of Giraffa
Authors: Alice Petzold, Alexandre Hassanin
Abstract:
The number of giraffe species has been in focus of interest since the exploration of sub-Saharan Africa by European naturalists during the 18th and 19th centuries, as previous taxonomists, like Geoffroy Saint-Hilaire, Richard Owen or William Edward de Winton, recognized two or three species of Giraffa. For the last decades, giraffes were commonly considered as a single species subdivided into nine subspecies. In this study, we have re-examined available nuclear and mitochondrial data. Our genetic admixture analyses of seven introns support three species: G. camelopardalis (i.e., northern giraffes including reticulated giraffes), G. giraffa (southern giraffe) and G. tippelskirchi (Masai giraffe). However, the nuclear alignments show small variation and our phylogenetic analyses provide high support only for the monophyly of G. camelopardalis. Comparisons with the mitochondrial tree revealed a robust conflict for the position and monophyly of G. giraffa and G. tippelskirchi, which is explained firstly by a mitochondrial introgression from Masai giraffe to southeastern giraffe, and secondly, by gene flow mediated by male dispersal between southern populations (subspecies angolensis and giraffa). We conclude that current data gives only moderate support for three giraffe species and point out that additional nuclear data need to be studied to revise giraffe taxonomy.Keywords: autosomal markers, Giraffidae, mitochondrial introgression, taxonomy
Procedia PDF Downloads 19213952 The Implications in the Use of English as the Medium of Instruction in Business Management Courses at Vavuniya Campus
Authors: Jeyaseelan Gnanaseelan, Subajana Jeyaseelan
Abstract:
The paper avails, in a systemic form, some of the results of the investigation into nature, functions, problems, and implications in the use of English as the medium of Instruction (EMI) in the Business Management courses at Vavuniya Campus of the University of Jaffna, located in the conflict-affected northern part of Sri Lanka. It is a case study of the responses of the students and the teachers from Tamil and Sinhala language communities of the Faculty of Business Studies. This paper analyzes the perceptions on the use of the medium, the EMI background, resources available and accessible, language abilities of the teachers and learners, learning style and pedagogy, the EMI methodology, the socio-economic and socio-political contexts typical of a non-native English learning context. The analysis is quantitative and qualitative. It finds out the functional perspective of the EMI in Sri Lanka and suggests practical strategies of contextualization and acculturation in the EMI organization and positions. The paper assesses the learner and teacher capacity in the use of English. The ethnic conflict and linguistic politics in Sri Lanka have contributed multiple factors to the current use of English as the medium. It has conflicted with its domestic realities and the globalization trends of the world at large which determines efficiency and effectiveness.Keywords: medium of instruction, English, business management, teaching and learning
Procedia PDF Downloads 12413951 Factors Influencing an Implementation of Financial Participation Programmes in Polish Companies - Some Relationships
Authors: Maciej Kozlowski, Agnieszka Piotrowska-Piatek
Abstract:
Purpose: This article analyses the most important financial participation programmes (FPP) in Poland to show the relationship between the programmes applied and the socio-economic results of enterprises and assesses the impact of participation on these results and the impact of selected factors on the introduction of FPP. Methodology: The research has been based on a questionnaire answered by senior management of listed Polish companies that had at least one out of three major FPPs in operation, namely share ownership, profit-sharing, or a stock option scheme. Findings: The results of the empirical study conducted indicate the existence of some peculiar relationships. The vast majority of schemes in Polish public companies are aimed at the participation of the management personnel; these programmes are narrow-based (only for management) and rather hermetic, with a high concentration of stocks or shares in the hands of the management. Conclusion: FPPs generally have a positive influence on enterprise functioning. However, the effects are more social than economic (no significant economic improvement after programme implementation). The paper contributes to the debate about financial participation and suggests actions to popularize these programmes on a wider scale.Keywords: financial participation, profit sharing, stock options, worker attitude, worker ownership
Procedia PDF Downloads 13213950 Consumer Perception of 3D Body Scanning While Online Shopping for Clothing
Authors: A. Grilec, S. Petrak, M. Mahnic Naglic
Abstract:
Technological development and the globalization in production and sales of clothing in the last decade have significantly influenced the changes in consumer relationship with the industrial-fashioned apparel and in the way of clothing purchasing. The Internet sale of clothing is in a constant and significant increase in the global market, but the possibilities offered by modern computing technologies in the customization segment are not yet fully involved, especially according to the individual customer requirements and body sizes. Considering the growing trend of online shopping, the main goal of this paper is to investigate the differences in customer perceptions towards online apparel shopping and particularly to discover the main differences in perceptions between customers regarding three different body sizes. In order to complete the research goal, the quantitative study on the sample of 85 Croatian consumers was conducted in 2017 in Zagreb, Croatia. Respondents were asked to indicate their level of agreement according to a five-point Likert scale ranging from strongly disagree (1) to strongly agree (5). To analyze attitudes of respondents, simple and descriptive statistics were used. The main findings highlight the differences in respondent perception of 3D body scanning, using 3D body scanning in Internet shopping, online apparel shopping habits regarding their body sizes.Keywords: consumer behavior, Internet, 3D body scanning, body types
Procedia PDF Downloads 15713949 Vibratinal Spectroscopic Identification of Beta-Carotene in Usnic Acid and PAHs as a Potential Martian Analogue
Authors: A. I. Alajtal, H. G. M. Edwards, M. A. Elbagermi
Abstract:
Raman spectroscopy is currently a part of the instrumentation suite of the ESA ExoMars mission for the remote detection of life signatures in the Martian surface and subsurface. Terrestrial analogues of Martian sites have been identified and the biogeological modifications incurred as a result of extremophilic activity have been studied. Analytical instrumentation protocols for the unequivocal detection of biomarkers in suitable geological matrices are critical for future unmanned explorations, including the forthcoming ESA ExoMars mission to search for life on Mars scheduled for 2018 and Raman spectroscopy is currently a part of the Pasteur instrumentation suite of this mission. Here, Raman spectroscopy using 785nm excitation was evaluated for determining various concentrations of beta-carotene in admixture with polyaromatic hydrocarbons and usnic acid have been investigated by Raman microspectrometry to determine the lowest levels detectable in simulation of their potential identification remotely in geobiological conditions in Martian scenarios. Information from this study will be important for the development of a miniaturized Raman instrument for targetting Martian sites where the biosignatures of relict or extant life could remain in the geological record.Keywords: raman spectroscopy, mars-analog, beta-carotene, PAHs
Procedia PDF Downloads 33413948 Off-Farm Work and Cost Efficiency in Staple Food Production among Small-Scale Farmers in North Central Nigeria
Authors: C. E. Ogbanje, S. A. N. D. Chidebelu, N. J. Nweze
Abstract:
The study evaluated off-farm work and cost efficiency in staple food production among small-scale farmers in North Central Nigeria. Multistage sampling technique was used to select 360 respondents (participants and non-participants in off-farm work). Primary data obtained were analysed using stochastic cost frontier and test of means’ difference. Capital input was lower for participants (N2,596.58) than non-participants (N11,099.14). Gamma (γ) was statistically significant. Farm size significantly (p<0.01) increased cost outlay for participants and non-participants. Average input prices of enterprises one and two significantly (p<0.01) increased cost. Sex, household size, credit obtained, formal education, farming experience, and farm income significantly (p<0.05) reduced cost inefficiency for non-participants. Average cost efficiency was 11%. Farm capital was wasted. Participants’ substitution of capital for labour did not put them at a disadvantage. Extension agents should encourage farmers to obtain financial relief from off-farm work but not to the extent of endangering farm cost efficiency.Keywords: cost efficiency, mean difference, North Central Nigeria, off-farm work, participants and non-participants, small-scale farmers
Procedia PDF Downloads 359