Search results for: continued fraction expansion

Authors: James Cairns, Marco Vezza, Richard Green, Donald MacVicar

Abstract:

Significant legislative changes are set to revolutionise the commercial shipping industry. Upcoming emissions restrictions will force operators to look at technologies that can improve the efficiency of their vessels -reducing fuel consumption and emissions. A device which may help in this challenge is the Ship Wind-Assisted Propulsion system (SWAP), an actively controlled aerofoil mounted vertically on the deck of a ship. The device functions in a similar manner to a sail on a yacht, whereby the aerodynamic forces generated by the sail reach an equilibrium with the hydrodynamic forces on the hull and a forward velocity results. Numerical and experimental testing of the SWAP device is presented in this study. Circulation control takes the form of a co-flow jet aerofoil, utilising both blowing from the leading edge and suction from the trailing edge. A jet at the leading edge uses the Coanda effect to energise the boundary layer in order to delay flow separation and create high lift with low drag. The SWAP concept has been originated by the research and development team at SMAR Azure Ltd. The device will be retrofitted to existing ships so that a component of the aerodynamic forces acts forward and partially reduces the reliance on existing propulsion systems. Wind tunnel tests have been carried out at the de Havilland wind tunnel at the University of Glasgow on a 1:20 scale model of this system. The tests aim to understand the airflow characteristics around the aerofoil and investigate the approximate lift and drag coefficients that an early iteration of the SWAP device may produce. The data exhibits clear trends of increasing lift as injection momentum increases, with critical flow attachment points being identified at specific combinations of jet momentum coefficient, Cµ, and angle of attack, AOA. Various combinations of flow conditions were tested, with the jet momentum coefficient ranging from 0 to 0.7 and the AOA ranging from 0° to 35°. The Reynolds number across the tested conditions ranged from 80,000 to 240,000. Comparisons between 2D computational fluid dynamics (CFD) simulations and the experimental data are presented for multiple Reynolds-Averaged Navier-Stokes (RANS) turbulence models in the form of normalised surface pressure comparisons. These show good agreement for most of the tested cases. However, certain simulation conditions exhibited a well-documented shortcoming of RANS-based turbulence models for circulation control flows and over-predicted surface pressures and lift coefficient for fully attached flow cases. Work must be continued in finding an all-encompassing modelling approach which predicts surface pressures well for all combinations of jet injection momentum and AOA.

Keywords: CFD, circulation control, Coanda, turbo wing sail, wind tunnel

Procedia PDF Downloads 113

Authors: Stanley Russell

Abstract:

Until the end of the 19th century, European painting dealt almost exclusively with the realistic representation of objects and landscapes, as can be seen in the work of realist artists like Gustav Courbet. Architects of the day typically made reference to and recreated historical precedents in their designs. The curriculum of the first architecture school in Europe, The Ecole des Beaux Artes, based on the study of classical buildings, had a profound effect on the profession. Painting exhibited an increasing level of abstraction from the late 19th century, with impressionism, and the trend continued into the early 20th century when Cubism had an explosive effect sending shock waves through the art world that also extended into the realm of architectural design. Architect /painter Le Corbusier with “Purism” was one of the first to integrate abstract painting and building design theory in works that were equally shocking to the architecture world. The interrelationship of the arts, including architecture, was institutionalized in the Bauhaus curriculum that sought to find commonality between diverse art disciplines. Renowned painter and Bauhaus instructor Vassily Kandinsky was one of the first artists to make a semi-scientific analysis of the elements in “non-objective” painting while also drawing parallels between painting and architecture in his book Point and Line to plane. Russian constructivists made abstract compositions with simple geometric forms, and like the De Stijl group of the Netherlands, they also experimented with full-scale constructions and spatial explorations. Based on the study of historical accounts and original artworks, of Impressionism, Cubism, the Bauhaus, De Stijl, and Russian Constructivism, this paper begins with a thorough explanation of the art theory and several key works from these important art movements of the late 19th and early 20th century. Similarly, based on written histories and first-hand experience of built and drawn works, the author continues with an analysis of the theories and architectural works generated by the same groups, all of which actively pursued continuity between their art and architectural concepts. With images of specific works, the author shows how the trend toward abstraction and geometric purity in painting coincided with a similar trend in architecture that favored simple unornamented geometries. Using examples like the Villa Savoye, The Schroeder House, the Dessau Bauhaus, and unbuilt designs by Russian architect Chernikov, the author gives detailed examples of how the intersection of trends in Art and Architecture led to a unique and fruitful period of creative synergy when the same concepts that were used by artists to generate paintings were also used by architects in the making of objects, space, and buildings. In Conclusion, this article examines the extremely pivotal period in art and architecture history from the late 19th to early 20th century when the confluence of art and architectural theory led to many painted, drawn, and built works that continue to inspire architects and artists to this day.

Keywords: modern art, architecture, design methodologies, modern architecture

Procedia PDF Downloads 104

Authors: Brady Manescau, Ilyas Sellami, Khaled Chetehouna, Charles De Izarra, Rachid Nait-Said, Fati Zidani

Abstract:

During a fire in an oil and gas refinery, several thermal accidents can occur and cause serious damage to people and environment. Among these accidents, the BLEVE (Boiling Liquid Expanding Vapor Explosion) is most observed and remains a major concern for risk decision-makers. It corresponds to a violent vaporization of explosive nature following the rupture of a vessel containing a liquid at a temperature significantly higher than its normal boiling point at atmospheric pressure. Their effects on the environment generally appear in three ways: blast overpressure, radiation from the fireball if the liquid involved is flammable and fragment hazards. In order to estimate the potential damage that would be caused by such an explosion, risk decision-makers often use quantitative risk analysis (QRA). This analysis is a rigorous and advanced approach that requires a reliable data in order to obtain a good estimate and control of risks. However, in most cases, the data used in QRA are obtained from the empirical correlations. These empirical correlations generally overestimate BLEVE effects because they are based on simplifications and do not take into account real parameters like the geometry effect. Considering that these risk analyses are based on an assessment of BLEVE effects on human life and plant equipment, more precise and reliable data should be provided. From this point of view, the CFD modeling of BLEVE effects appears as a solution to the empirical law limitations. In this context, the main objective is to develop a numerical tool in order to predict BLEVE thermal effects using the CFD code FDS version 6. Simulations are carried out with a mesh size of 1 m. The fireball source is modeled as a vertical release of hot fuel in a short time. The modeling of fireball dynamics is based on a single step combustion using an EDC model coupled with the default LES turbulence model. Fireball characteristics (diameter, height, heat flux and lifetime) issued from the large scale BAM experiment are used to demonstrate the ability of FDS to simulate the various steps of the BLEVE phenomenon from ignition up to total burnout. The influence of release parameters such as the injection rate and the radiative fraction on the fireball heat flux is also presented. Predictions are very encouraging and show good agreement in comparison with BAM experiment data. In addition, a numerical study is carried out on an operational propane accumulator in an Algerian gas processing plant of SONATRACH company located in the Hassi R’Mel Gas Field (the largest gas field in Algeria).

Keywords: BLEVE effects, CFD, FDS, fireball, LES, QRA

Procedia PDF Downloads 166

Authors: G. Andreutti, G. Saccone, D. Lucariello, C. Pirozzi, S. Franchitti, R. Borrelli, C. Toscano, P. Caso, G. Ferraro, C. Pascarella

Abstract:

The reduction of greenhouse gases and pollution emissions is a worldwide environmental issue. The amount of CO₂ released by an aircraft is associated with the amount of fuel burned, so the improvement of engine thermo-mechanical efficiency and specific fuel consumption is a significant technological driver for aviation. Moreover, with the prospect that avgas will be phased out, an engine able to use more available and cheaper fuels is an evident advantage. An advanced aeronautical Diesel engine, because of its high efficiency and ability to use widely available and low-cost jet and diesel fuels, is a promising solution to achieve a more fuel-efficient aircraft. On the other hand, a Diesel engine has generally a higher overall weight, if compared with a gasoline one of same power performances. Fixing the MTOW, Max Take-Off Weight, and the operational payload, this extra-weight reduces the aircraft fuel fraction, partially vinifying the associated benefits. Therefore, an effort in weight saving manufacturing technologies is likely desirable. In this work, in order to achieve the mentioned goals, innovative Electron Beam Melting – EBM, Additive Manufacturing – AM technologies were applied to a two-stroke, common rail, GF56 Diesel engine, developed by the CMD Company for aeronautic applications. For this purpose, a consortium of academic, research and industrial partners, including CMD Company, Italian Aerospace Research Centre – CIRA, University of Naples Federico II and the University of Salerno carried out a technological project, funded by the Italian Minister of Education and Research – MIUR. The project aimed to optimize the baseline engine in order to improve its performance and increase its airworthiness features. This project was focused on the definition, design, development, and application of enabling technologies for performance improvement of GF56. Weight saving of this engine was pursued through the application of EBM-AM technologies and in particular using Arcam AB A2X machine, available at CIRA. The 3D printer processes titanium alloy micro-powders and it was employed to realize new connecting rods of the GF56 engine with an additive-oriented design approach. After a preliminary investigation of EBM process parameters and a thermo-mechanical characterization of titanium alloy samples, additive manufactured, innovative connecting rods were fabricated. These engine elements were structurally verified, topologically optimized, 3D printed and suitably post-processed. Finally, the overall performance improvement, on a typical General Aviation aircraft, was estimated, substituting the conventional engine with the optimized GF56 propulsion system.

Keywords: aeronautic propulsion, additive manufacturing, performance improvement, weight saving, piston engine

Procedia PDF Downloads 119

Authors: Phusit Phukamchanoad, Bua Srikos

Abstract:

Research aimed to study the characteristics of a community in the social, economical and cultural context. This research used interviews and surveys members in Patthana Soi Ranongklang community, Dusit District, Bangkok. The results are as follows: In terms of overall conditions and characteristics, Patthana Soi Ranongklang community is located on the property of Treasury Department. 50 years ago the location of this community consisted of paddy fields with limited convenience in terms of transportation. Rama V Road was only a small narrow road with only three-wheelers and no buses. The majority of community members moved in from Makkhawan Rangsan Bridge. Thus, most community members were either workers or government officials as they were not the owners of the land. Therefore, there were no primary occupations within this 7 acres of the community. The development of the community started in 1981. At present, the community is continuously being developed and modernization is rapidly flowing in. One of the reasons was because main roads were amended, especially Rama V Road that allows more convenient transportation, leading to heightened citizens’ convenience. In terms of the economy and society, the research found out that the development and expansion of Rama V Road cause a change in the conditions of the area and buildings. Some building were improved and changed along the time, as well as the development of new facilities that cause the community members to continually become more materialistic. Jobs within the community started to appear, and areas were improved to allow for new building and housing businesses. The trend of jobs become more in variety, in terms of both jobs at home, such as workers, merchandizing, and small own businesses, and jobs outside the community, which became much more convenient as car drivers are used to the narrow roads inside the community. The location of the community next to Rama V Road also allows helo from government agencies to reach the community with ease. Moreover, the welfare of the community was well taken care of by the community committee. In terms of education, the research found that there are two schools: Wat Pracharabuedham School and Wat Noi Noppakun School, that are providing education within the community. The majority of the community received Bachelor degrees. In areas of culture, the research found that the culture, traditions, and beliefs of people in the community were mainly transferred from the old community, especially beliefs in Buddhism as the majority are Bhuddists. The main reason is because the old community was situated near Wat Makut Kasattriyaram. Therefore, the community members have always had Buddhist temples as the center of the community. In later years, more citizens moved in and bring along culture, traditions, and beliefs with them. The community members also took part in building a Dharma hall named Wat Duang Jai 72 Years Ranong Klang. Traditions that community members adhere to since the establishment of the community are the New Year merit making and Songkran Tradition.

Keywords: social capital, culture, Patthana Soi Ranongklang community, way of life

Procedia PDF Downloads 431

Authors: Desmond Appiah, Fan Zhang, Shouqi Yuan, Wei Xueyuan, Stephen N. Asomani

Abstract:

The side channel pump has distinctive hydraulic performance characteristics over other vane pumps because of its generation of high pressure heads in only one impeller revolution. Hence, there is soaring utilization and application in the fields of petrochemical, food processing fields, automotive and aerospace fuel pumping where high heads are required at low flows. The side channel pump is characterized by unstable flow because after fluid flows into the impeller passage, it moves into the side channel and comes back to the impeller again and then moves to the next circulation. Consequently, the flow leaves the side channel pump following a helical path. However, the pressure fluctuation exhibited in the flow greatly contributes to the unwanted noise and vibration which is associated with the flow. In this paper, a side channel pump prototype was examined thoroughly through numerical calculations based on SST k-ω turbulence model to ascertain the pressure fluctuation behavior. The pressure fluctuation intensity of the 3D unstable flow dynamics were carefully investigated under different working conditions 0.8QBEP, 1.0 QBEP and 1.2QBEP. The results showed that the pressure fluctuation distribution around the pressure side of the blade is greater than the suction side at the impeller and side channel interface (z=0) for all three operating conditions. Part-load condition 0.8QBEP recorded the highest pressure fluctuation distribution because of the high circulation velocity thus causing an intense exchanged flow between the impeller and side channel. Time and frequency domains spectra of the pressure fluctuation patterns in the impeller and the side channel were also analyzed under the best efficiency point value, QBEP using the solution from the numerical calculations. It was observed from the time-domain analysis that the pressure fluctuation characteristics in the impeller flow passage increased steadily until the flow reached the interrupter which separates low-pressure at the inflow from high pressure at the outflow. The pressure fluctuation amplitudes in the frequency domain spectrum at the different monitoring points depicted a gentle decreasing trend of the pressure amplitudes which was common among the operating conditions. The frequency domain also revealed that the main excitation frequencies occurred at 600Hz, 1200Hz, and 1800Hz and continued in the integers of the rotating shaft frequency. Also, the mass flow exchange plots indicated that the side channel pump is characterized with many vortex flows. Operating conditions 0.8QBEP, 1.0 QBEP depicted less and similar vortex flow while 1.2Q recorded many vortex flows around the inflow, middle and outflow regions. The results of the numerical calculations were finally verified experimentally. The performance characteristics curves from the simulated results showed that 0.8QBEP working condition recorded a head increase of 43.03% and efficiency decrease of 6.73% compared to 1.0QBEP. It can be concluded that for industrial applications where the high heads are mostly required, the side channel pump can be designed to operate at part-load conditions. This paper can serve as a source of information in order to optimize a reliable performance and widen the applications of the side channel pumps.

Keywords: exchanged flow, pressure fluctuation, numerical simulation, side channel pump

Procedia PDF Downloads 107

Authors: Rana Parween, Rob Marchant

Abstract:

With the continued loss of global biodiversity despite the application of modern conservation techniques, it has become crucial to investigate non-conventional methods. Accelerated destruction of ecosystems due to altered land use, climate change, cultural and social change, necessitates the exploration of society-biodiversity attitudes and links. While the loss of species and their extinction is a well-known and well-documented process that attracts much-needed attention from researchers, academics, government and non-governmental organizations, the loss of traditional ecological knowledge and practices is more insidious and goes unnoticed. The growing availability of 'indirect experiences' such as the internet and media are leading to a disaffection towards nature and the 'Extinction of Experience'. Exacerbated by the lack of documentation of traditional practices and skills, there is the possibility for the 'extinction' of traditional practices and skills before they are fully recognized and captured. India, as a mega-biodiverse country, is also known for its historical conservation strategies entwined in traditional beliefs. Indigenous communities hold skillsets, knowledge, and traditions that have accumulated over multiple generations and may play an important role in conserving biodiversity today. This study explores the differences in knowledge and attitudes towards conserving biodiversity, of three different stakeholder groups living around Jim Corbett National Park, based on their age, traditions, and association with the protected area. A triangulation designed multi-strategy investigation collected qualitative and quantitative data through a questionnaire survey of village elders, the general public, and forest officers. Following an inductive approach to analyzing qualitative data, the thematic content analysis was followed. All coding and analysis were completed using NVivo 11. Although the village elders and some general public had vast amounts of traditional knowledge, most of it was related to animal husbandry and the medicinal value of plants. Village elders were unfamiliar with the concept of the term ‘biodiversity’ albeit their way of life and attitudes ensured that they care for the ecosystem without having the scientific basis underpinning biodiversity conservation. Inherently, village elders were keen to conserve nature; the superimposition of governmental policies without any tangible benefit or consultation was seen as detrimental. Alienating villagers and consequently the village elders who are the reservoirs of traditional knowledge would not only be damaging to the social network of the area but would also disdain years of tried and tested techniques held by the elders. Forest officers advocated for biodiversity and conservation education for women and children. Women, across all groups, when questioned about nature conservation, showed more interest in learning and participation. Biodiversity not only has an ethical and cultural value, but also plays a role in ecosystem function and, thus, provides ecosystem services and supports livelihoods. Therefore, underpinning and using traditional knowledge and incorporating them into programs of biodiversity conservation should be explored with a sense of urgency.

Keywords: biological diversity, mega-biodiverse countries, traditional ecological knowledge, society-biodiversity links

Procedia PDF Downloads 83

Authors: Dorottya Guban, Irina Borbath, Istvan Bakos, Peter Nemeth, Andras Tompos

Abstract:

One of the greatest challenges of the implementation of polymer electrolyte membrane fuel cells (PEMFCs) is to find active and durable electrocatalysts. The cell performance is always limited by the oxygen reduction reaction (ORR) on the cathode since it is at least 6 orders of magnitude slower than the hydrogen oxidation on the anode. Therefore high loading of Pt is required. Catalyst corrosion is also more significant on the cathode, especially in case of mobile applications, where rapid changes of loading have to be tolerated. Pt-Sn bulk alloys and SnO2-decorated Pt3Sn nanostructures are among the most studied bimetallic systems for fuel cell applications. Exclusive formation of supported Sn-Pt alloy phases with different Pt/Sn ratios can be achieved by using controlled surface reactions (CSRs) between hydrogen adsorbed on Pt sites and tetraethyl tin. In this contribution our results for commercial and a home-made 20 wt.% Pt/C catalysts modified by tin anchoring via CSRs are presented. The parent Pt/C catalysts were synthesized by modified NaBH4-assisted ethylene-glycol reduction method using ethanol as a solvent, which resulted either in dispersed and highly stable Pt nanoparticles or evenly distributed raspberry-like agglomerates according to the chosen synthesis parameters. The 20 wt.% Pt/C catalysts prepared that way showed improved electrocatalytic performance in the ORR and stability in comparison to the commercial 20 wt.% Pt/C catalysts. Then, in order to obtain Sn-Pt/C catalysts with Pt/Sn= 3 ratio, the Pt/C catalysts were modified with tetraethyl tin (SnEt4) using three and five consecutive tin anchoring periods. According to in situ XPS studies in case of catalysts with highly dispersed Pt nanoparticles, pre-treatment in hydrogen even at 170°C resulted in complete reduction of the ionic tin to Sn0. No evidence of the presence of SnO2 phase was found by means of the XRD and EDS analysis. These results demonstrate that the method of CSRs is a powerful tool to create Pt-Sn bimetallic nanoparticles exclusively, without tin deposition onto the carbon support. On the contrary, the XPS results revealed that the tin-modified catalysts with raspberry-like Pt agglomerates always contained a fraction of non-reducible tin oxide. At the same time, they showed increased activity and long-term stability in the ORR than Pt/C, which was assigned to the presence of SnO2 in close proximity/contact with Pt-Sn alloy phase. It has been demonstrated that the content and dispersion of the fcc Pt3Sn phase within the electrocatalysts can be controlled by tuning the reaction conditions of CSRs. The bimetallic catalysts displayed an outstanding performance in the ORR. The preparation of a highly dispersed 20Pt/C catalyst permits to decrease the Pt content without relevant decline in the electrocatalytic performance of the catalysts.

Keywords: anode catalyst, cathode catalyst, controlled surface reactions, oxygen reduction reaction, PtSn/C electrocatalyst

Procedia PDF Downloads 208

Authors: Ani Eda Njwe

Abstract:

Cameroon is a bilingual and bijural country in West and Central Africa. The current president has been in power since 1982, which makes him the longest-serving president in the world. The length of his presidency is one of the major causes of the ongoing political instability in the country. The preamble of the Cameroonian constitution commits Cameroon to respect international law and human rights. It provides that these laws should be translated into national laws, and respected by all spheres of government and public service. Cameroon is a signatory of several international human rights laws and conventions. In theory, the citizens of Cameroon have adequate legal protection against the violation of their human rights for political reasons. The ongoing political crisis in Cameroon erupted after the Anglophone lawyers and teachers launched a protest against the hiring of Francophone judges in Anglophone courts; and the hiring of Francophone teachers in Anglophone schools. In retaliation, the government launched a military crackdown on protesters and civilians, conducted arbitrary arrests on Anglophones, raped and maimed civilians, and declared a state of emergency in the Anglophone provinces. This infuriated the Anglophone public, causing them to create a secessionist movement, requesting the Independence of Anglophone Cameroon and demanding a separate country called Ambazonia. The Ambazonian armed rebel forces have ever since launched guerrilla attacks on government troops. This fighting has deteriorated into a war between the Ambazonians and the Cameroon government. The arbitrary arrests and unlawful imprisonments have continued, causing the closure of Anglophone schools since November 2016. In October 2018, Cameroon held presidential elections. Before the electoral commission announced the results, the opposition leader, a Francophone, declared himself winner, following a leak of the polling information. This led to his imprisonment. This research has the objective of finding out whether the government’s reactions to protesters and opposition is lawful, under national and international laws. This research will also verify if the prison conditions of political prisoners meet human rights standards. Furthermore, this research seeks detailed information obtained from current political prisoners and detainees on their experiences. This research also aims to highlight the effort being made internationally, towards bringing awareness and finding a resolution to the war in Cameroon. Finally, this research seeks to elucidate on the efforts which human rights organisations have made, towards overseeing the respect of human rights in Cameroon. This research adopts qualitative methods, whereby data were collected using semi-structured interviews of political detainees, and questionnaires. Also, data was collected from secondary sources such as; scholarly articles, newspaper articles, web sources, and human rights reports. From the data collected, the findings were analysed using the content analysis research technique. From the deductions, recommendations have been made, which human rights organisations, activists, and international bodies can implement, to cause the Cameroonian government to stop unlawful arrests and reinstate the respect of human rights and the rule of law in Cameroon.

Keywords: arbitrary arrests, Cameroon, human rights, political

Procedia PDF Downloads 93

Authors: Lauren G. Coggins

Abstract:

Catheter-associated urinary tract infections (CAUTI) and central line-associated bloodstream infections (CLABSI) are among the most common healthcare-associated infections (HAI), contributing to prolonged lengths of stay, greater costs of patient care, and increased patient mortality. Evidence-based preventative care bundles exist to establish consistent, safe patient-care practices throughout an entire organization, helping to ensure the collective application of care strategies that aim to improve patient outcomes and minimize complications. The cardiac intensive care unit at a nationally ranked teaching and research hospital in the United States exceeded its annual CAUTI and CLABSI targets in the fiscal year 2019, prompting examination into the unit’s infection prevention efforts that included preventative care bundles for both HAIs. Adherence to the CAUTI and CLABSI preventative care bundles was evaluated through frequent audits conducted over three months, using standards and resources from The Joint Commission, a globally recognized leader in quality improvement in healthcare and patient care safety. The bundle elements with the lowest scores were identified as the most commonly missed elements. Three elements from both bundles, six elements in total, served as key content areas for the educational interventions targeted to bedside nurses. The CAUTI elements included appropriate urinary catheter order, appropriate continuation criteria, and urinary catheter care. The CLABSI elements included primary tubing compliance, needleless connector compliance, and dressing change compliance. An integrated, multi-platform education campaign featured content on each CAUTI and CLABSI preventative care bundle in its entirety, with additional reinforcement focused on the lowest scoring elements. One-on-one educational materials included an informational pamphlet, badge buddy, a presentation to reinforce nursing care standards, and real-time application through case studies and electronic health record demonstrations. A digital hub was developed on the hospital’s Intranet for quick access to unit resources, and a bulletin board helped track the number of days since the last CAUTI and CLABSI incident. Audits continued to be conducted throughout the education campaign, and staff were given real-time feedback to address any gaps in adherence. Nearly every nurse in the cardiac intensive care unit received all educational materials, and adherence to all six key bundle elements increased after the implementation of educational interventions. Recommendations from this implementation include providing consistent, comprehensive education across multiple teaching tools and regular audits to track adherence. The multi-platform education campaign brought focus to the evidence-based CAUTI and CLABSI bundles, which in turn will help to reduce CAUTI and CLABSI rates in clinical practice.

Keywords: education, healthcare-associated infections, infection, nursing, prevention

Procedia PDF Downloads 92

Authors: M. Abd El Hamid Ezzat

Abstract:

Two field trials were conducted to study the effect of plant densities i.e., 190, 222, 266, 330 and 440 10³ plants ha⁻¹ on morphological characters, physiological and yield attributes of two faba bean types viz. determinate (FLIP-87 -117 strain) and indeterminate (c.v. Giza-461). The results showed that the indeterminate plants significantly surpassed the determinate plants in plant height at 75 and 90 days from sowing, number of leaves at all growth stages and dry matter accumulation at 45 and 90 days from sowing. Determinate plants possessed greater number of side branches than that of the indeterminate plants, but it was only significant at 90 days from sowing. Greater number of flowers were produced by the indeterminate plants than that of the determinate plants at 75 and 90 days from sowing, and although shedding was obvious in both types, it was greater in the determinate plants as compared with the indeterminate one at 90 days from sowing. Increasing plant density resulted in reductions in number of leaves, branches flowers and dry matter accumulation per plant of both faba bean types. However, plant height criteria took a reversible magnitude. Moreover, under all rates of plant densities the indeterminate type plants surpassed the determinate plants in all growth characters studied except for number of branches per plant at 90 days from sowing. The indeterminate plant leaves significantly contained greater concentrations of photosynthetic pigments i.e., chl. a, b and carotenoids than those found in the determinate plant leaves. Also, the data showed significant reduction in photosynthetic pigments concentration as planting density increases. Light extinction coefficient (K) values reached their maximum level at 60 days from sowing, then it declined sharply at 75 days from sowing. The data showed that the illumination inside the determinate faba bean canopies was better than the indeterminate plants. (K) values tended to increase as planting density increases, meanwhile, significant interactions were reported between faba bean type as planting density on (K) at all growth stages. Both of determinate and indeterminate faba bean plant leaves reached their maximum expansion at 75 days from sowing reflecting the highest LAI values, then their declined in the subsequent growth stage. The indeterminate faba bean plants significantly surpassed the determinate plants in LAI up to 75 days from sowing. Growth analysis showed that NAR, RGR and CGR reached their maximum rates at (60-75 days growth stage). Faba bean types did not differ significantly in NAR at the early growth stage. The indeterminate plants were able to grow faster with significant CGR values than the determinate plants. The indeterminate faba bean plants surpassed the determinate ones in number of seeds/pod and per plant, 100-seed weight, seed yield per plant and per hectare at all rates of plant density. Seed yield increased with increasing plant densities of both types. The highest seed yield was attained for both types 440 103 plants ha⁻¹.

Keywords: determinate, indeterminate faba bean, Physiological attributes, yield attributes

Procedia PDF Downloads 207

Authors: D. Norton

Abstract:

This qualitative study focuses on the lived experience and displacement of young white-collar masculinities in Japan. In recent years, the salaryman lifestyle has undergone significant disruption - increased competition for regular employment, rise in non-regular structurings of labour across public/private sectors, and shifting role expectations within the home. Despite this, related scholarship hints at a continued reinforcement of the traditional male gender role - that the salaryman remains a key benchmark of Japanese masculine identity. For those in structural proximity to these more ‘normative’ performativities, interest lies their engagement with such narratives - how they make sense of their masculinity in response to stated changes. In light of the historical emphasis on labour and breadwinning logics, notions of respective security or precarity generated as a result remain unclear. Similarly, concern extends to developments within the private sphere - by what means young white-collar men construct ideas of singlehood and companionship according to traditional gender ideologies or more contemporary, flexible readings. The influence of these still-emergent status distinctions on the logics of the social group in question is yet to be explored in depth by gender scholars. This project, therefore, focuses on a salaryman archetype as hegemonic - its transformation amidst these changes and socialising mechanisms that continue to legitimate unequal gender hierarchies. For data collection, a series of ethnographic interviews were held over a period of 12 months with university-educated, white-collar male employees from both Osaka and the Greater Tokyo Area. Findings suggest a modern salaryman ideal reflecting both continuities and shifts within white-collar employment. Whilst receptive to more contemporary workplace practices, the narratives of those interviewed remain imbued with logics supporting patterns of internal hegemony. Regular/non-regular distinction emerged as the foremost variable for both material and discursive patterns of white-collar stratification, with variants of displacement for each social group. Despite the heightened valorisation of stable employment, regular workers articulated various concerns over a model of corporate masculinity seen to be incompatible with recent socioeconomic developments. Likewise, non-regular employees face detachment owing to a still-inflexible perception of their working masculinity as marginalized amidst economic precarity. In seeking to negotiate respective challenges, those interviewed demonstrated an engagement with various concurrent social changes that would often either accommodate, reinforce, or expand upon traditional role behaviours. Few of these narratives offered any notable transgression of said ideal, however, suggesting that within the spectre of white-collar employment in Japan for the near future, any substantive transformation of corporate masculinity remains dependant upon economic developments, less so the agency of those involved.

Keywords: gender ideologies, hegemonic masculinity, Japan, white-collar employment

Procedia PDF Downloads 101

Authors: Zipeng Zhang, Yat C. Wong, Arul Arulrajah

Abstract:

Since automobiles became widely popular around the early 20th century, end-of-life tyres have been one of the major types of waste humans encounter. Every minute, there are considerable quantities of tyres being disposed of around the world. Most end-of-life tyres are simply landfilled or simply stockpiled, other than recycling. To address the potential issues caused by tyre waste, incorporating it into construction materials can be a possibility. This research investigated the viability of manufacturing bricks using mill waste and tyre crumb by alkali-activation at a relatively low temperature. The mill waste was extracted from a brick factory located in Melbourne, Australia, and the tyre crumbs were supplied by a local recycling company. As the main precursor, the mill waste was activated by the alkaline solution, which was comprised of sodium hydroxide (8m) and sodium silicate (liquid). The introduction ratio of alkaline solution (relative to the solid weight) and the weight ratio between sodium hydroxide and sodium silicate was fixed at 20 wt.% and 1:1, respectively. The tyre crumb was introduced to substitute part of the mill waste at four ratios by weight, namely 0, 5, 10 and 15%. The mixture of mill waste and tyre crumbs were firstly dry-mixed for 2 min to ensure the homogeneity, followed by a 2.5-min wet mixing after adding the solution. The ready mixture subsequently was press-moulded into blocks with the size of 109 mm in length, 112.5 mm in width and 76 mm in height. The blocks were cured at 50°C with 95% relative humidity for 2 days, followed by a 110°C oven-curing for 1 day. All the samples were then placed under the ambient environment until the age of 7 and 28 days for testing. A series of tests were conducted to evaluate the linear shrinkage, compressive strength and water absorption of the samples. In addition, the microstructure of the samples was examined via the scanning electron microscope (SEM) test. The results showed the highest compressive strength was 17.6 MPa, found in the 28-day-old group using 5 wt.% tyre crumbs. Such strength has been able to satisfy the requirement of ASTM C67. However, the increasing addition of tyre crumb weakened the compressive strength of samples. Apart from the strength, the linear shrinkage and water absorption of all the groups can meet the requirements of the standard. It is worth noting that the use of tyre crumbs tended to decrease the shrinkage and even caused expansion when the tyre content was over 15 wt.%. The research also found that there was a significant reduction in compressive strength for the samples after water absorption tests. In conclusion, the tyre crumbs have the potential to be used as a filler material in brick manufacturing, but more research needs to be done to tackle the durability problem in the future.

Keywords: bricks, mill waste, tyre crumbs, waste recycling

Procedia PDF Downloads 103

Authors: Faraj M. Elkhatri, Hana Ellafi

Abstract:

In recent years, there has been a growing recognition of the potential of marine-based functional foods and combination therapies in promoting a healthy lifestyle and exploring their effectiveness in preventing or treating diseases. The combination of marine bioactive compounds or extracts offers synergistic or enhancement effects through various mechanisms, including multi-target actions, improved bioavailability, enhanced bioactivity, and mitigation of potential adverse effects. Both the green-lipped mussel (GLM) and fucoidan derived from brown seaweed are rich in bioactivities. These two, mussel and fucoidan, have not been previously formulated together. This study aims to combine GLM oil from Perna canaliculus with low molecular weight fucoidan (LMWF) extracted from Undaria pinnatifida to investigate the unique mixture’s anti-inflammatory and antioxidant properties. The cytotoxicity of individual compounds and combinations was assessed using the MTT assay in (THP-1 and RAW264.7) cell lines. The anti-inflammatory activity of mussel-fucoidan was evaluated by treating LPS-stimulated human monocyte and macrophage (THP1-1) cells. Subsequently, the inflammatory cytokines released into the supernatant of these cell lines were quantified via ELISA. Antioxidant activity was determined by using the free radical scavenging assay (DPPH). DPPH assay demonstrated that the radical scavenging activity of the combinations, particularly at concentrations exceeding 1 mg/ml, showed a significantly higher percentage of inhibition when compared to the individual component. This suggests an enhancement effect when the two compounds are combined, leading to increased antioxidant activity. In terms of immunomodulatory activity, the individual compounds exhibited distinct behaviors. GLM oil displayed a higher ability to suppress the cytokine TNF- compared to LMWF. Interestingly, the LMWF fraction, when used individually, did not demonstrate TNF- suppression. However, when combined with GLM, the TNF- suppression (anti-inflammatory) activity of the combination was better than GLM or LWMF alone. This observation underscores the potential for enhancement interactions between the two components in terms of anti-inflammatory properties. This study revealed that each individual compound, LMWF, and GLM, possesses unique and notable bioactivity. The combination of these two individual compounds results in an enhancement effect, where the bioactivity of each is enhanced, creating a superior combination. This suggests that the combination of LMWF and GLM has the potential to offer a more potent and multifaceted therapeutic effect, particularly in the context of antioxidant and anti-inflammatory activities. These findings hold promise for the development of novel therapeutic interventions or supplements that harness the enhancement effects.

Keywords: formation damage, porosity loses, pore throat, quartz cement

Procedia PDF Downloads 40

Authors: Claudia Mertens, Amanda Shufflebarger

Abstract:

Step one: What we know about effective learning for pupils with SEN: results of 2 systematic reviews: Before establishing principles and practices for teaching and learning of pupils with SEN, we need a good overview of the results of empirical studies conducted in the respective field. Therefore, two systematic reviews on the use of digital tools in inclusive and non-inclusive school settings were conducted - taking into consideration studies published in German: One systematic review included studies having undergone a peer review process, and the second included studies without peer review). The results (collaboration of two German universities) will be presented during the conference. Step two: Students’ results of a research lab on “inclusive media education”: On this basis, German students worked on “inclusive media education” in small research projects (duration: 1 year). They were “education majors” enrolled in a course on inclusive media education. They conducted research projects on topics ranging from smartboards in inclusive settings, digital media in gifted math education, Tik Tok in German as a Foreign Language education and many more. As part of their course, the German students created an academic conference poster. In the conference, the results of these research projects/papers are put into the context of the results of the systematic reviews. Step three: Global Classroom: The German students’ posters were critically discussed in a global classroom in cooperation with Indiana University East (USA) and Hamburg University (Germany) in the winter/spring term of 2022/2023. 15 students in Germany collaborated with 15 students at Indiana University East. The IU East student participants were enrolled in “Writing in the Arts and Sciences,” which is specifically designed for pre-service teachers. The joint work began at the beginning of the Spring 2023 semester in January 2023 and continued until the end of the Uni Hamburg semester in February 2023. Before January, Uni Hamburg students had been working on a research project individually or in pairs. Didactic Approach: Both groups of students posted a brief video or audio introduction to a shared Canvas discussion page. In the joint long synchronous session, the students discussed key content terms such as inclusion, inclusive, diversity, etc., with the help of prompt cards, and they compared how they understood or applied these terms differently. Uni Hamburg students presented drafts of academic posters. IU East students gave them specific feedback. After that, IU East students wrote brief reflections summarizing what they learned from the poster. After the class, small groups were expected to create a voice recording reflecting on their experiences. In their recordings, they examined critical incidents, highlighting what they learned from these incidents. Major results of the student research and of the global classroom collaboration can be highlighted during the conference. Results: The aggregated results of the two systematic reviews AND of the research lab/global classroom can now be a sound basis for 1) improving accessibility for students with SEN and 2) for adjusting teaching materials and concepts to the needs of the students with SEN - in order to create successful learning.

Keywords: digitalization, inclusion, inclusive media education, global classroom, systematic review

Procedia PDF Downloads 61

Authors: Venkata Buddharaju, Irene Mccarron, Hazel Alba

Abstract:

Introduction: Male external catheters (MECs) are commonly used to collect and drain urine. MECs are increasingly used in acute care, long-term acute care hospitals, and nursing facilities, and in other patients as an alternative to invasive urinary catheters to reduce catheter-associated urinary tract infections (CAUTI).MECs are also used to avoid the need for incontinence pads and diapers. Most of the Male External Catheters are held in place by skin adhesive, with the exception of a few, which uses a foam strap clamp around the penile shaft. The adhesive condom catheters typically stay for 24 hours or less. It is also a common practice that extra skin adhesive tape is wrapped around the condom catheter for additional security of the device. The fixed nature of the adhesive will not allow the normal skin expansion of penile size over time. The adhesive can cause skin irritation, redness, erosion, and skin damage. Acanthus condom catheter (ACC) is a patented, specially designed, stretchable silicone catheter without adhesive, adapts to the size and contour of the penis. It is held in place with a single elastic strap that wraps around the lower back and tied to the opposite catheter ring holescriss cross. It can be reused for up to 5 days on the same patient after daily cleaning and washingpotentially reducing cost. Methods: The study was conducted from September 17th to October 8th, 2020. The nursing staff was educated and trained on how to use and reuse the catheter. After identifying five (5) appropriate patients, the catheter was placed and maintained by nursing staff. The data on the ease of use, leak, and skin damage were collected and reported by nurses to the nursing education department of the hospital for analysis. Setting: RML Chicago, long-term acute care hospital, an affiliate of Loyola University Medical Center, Chicago, IL USA. Results: The data showed that the catheter was easy to apply, remove, wash and reuse, without skin problems or urine infections. One patient had used for 16 days after wash, reuse, and replacement without any urine leak or skin issues. A minimal leak was observed on two patients. Conclusion: Acanthus condom catheter was easy to use, functioned well with minimal or no leak during use and reuse. The skin was intact in all patients studied. There were no urinary tract infections in any of the studied patients.

Keywords: CAUTI, male external catheter, reusable, skin adhesive

Procedia PDF Downloads 85

Authors: Antonina Semakova, Karim Mynbaev, Nikolai Bazhenov, Anton Chernyaev, Sergei Kizhaev, Nikolai Stoyanov

Abstract:

At present, heterostructures are used for fabrication of almost all types of optoelectronic devices. Our research focuses on the optoelectronic properties of InAs(Sb) solid solutions that are widely used in fabrication of light emitting diodes (LEDs) operating in middle wavelength infrared range (MWIR). This spectral range (2-6 μm) is relevant for laser diode spectroscopy of gases and molecules, for systems for the detection of explosive substances, medical applications, and for environmental monitoring. The fabrication of MWIR LEDs that operate efficiently at room temperature is mainly hindered by the predominance of non-radiative Auger recombination of charge carriers over the process of radiative recombination, which makes practical application of LEDs difficult. However, non-radiative recombination can be partly suppressed in quantum-well structures. In this regard, studies of such structures are quite topical. In this work, electroluminescence (EL) of LED heterostructures based on InAs(Sb) epitaxial films with the molar fraction of InSb ranging from 0 to 0.09 and multi quantum-well (MQW) structures was studied in the temperature range 4.2-300 K. The growth of the heterostructures was performed by metal-organic chemical vapour deposition on InAs substrates. On top of the active layer, a wide-bandgap InAsSb(Ga,P) barrier was formed. At low temperatures (4.2-100 K) stimulated emission was observed. As the temperature increased, the emission became spontaneous. The transition from stimulated emission to spontaneous one occurred at different temperatures for structures with different InSb contents in the active region. The temperature-dependent carrier lifetime, limited by radiative recombination and the most probable Auger processes (for the materials under consideration, CHHS and CHCC), were calculated within the framework of the Kane model. The effect of various recombination processes on the carrier lifetime was studied, and the dominant role of Auger processes was established. For MQW structures quantization energies for electrons, light and heavy holes were calculated. A characteristic feature of the experimental EL spectra of these structures was the presence of peaks with energy different from that of calculated optical transitions between the first quantization levels for electrons and heavy holes. The obtained results showed strong effect of the specific electronic structure of InAsSb on the energy and intensity of optical transitions in nanostructures based on this material. For the structure with MQWs in the active layer, a very weak temperature dependence of EL peak was observed at high temperatures (>150 K), which makes it attractive for fabricating temperature-resistant gas sensors operating in the middle-infrared range.

Keywords: Electroluminescence, InAsSb, light emitting diode, quantum wells

Procedia PDF Downloads 185

Authors: Jane Oliver, Angeline Ferdinand, Jessica Kaufman, Peta Edler, Nicole Allard, Margie Danchin, Katherine B. Gibney

Abstract:

Background: The cohealth Health Concierge program operated in Melbourne, Australia, from July 2020 to 30 June 2022. The program was designed to provide place-based peer-to-peer COVID-19 education and support to culturally and linguistically diverse residents of high-rise public housing estates. During this time, the COVID-19 public health response changed frequently. We conducted a mixed-methods evaluation to determine the program’s impact on residents’ trust, engagement and communication with health services and public health activities. Methods: The RE-AIM model was used to assess program reach, effectiveness, adoption, implementation and maintenance and the evaluation was informed by a Project Reference Group including end-users. Data were collected between March and May 2022 in four estates where the program operated. We surveyed 301 residents, conducted qualitative interviews with 32 stakeholders and analyzed data from 20,901 forms reporting interactions between Health Concierges and residents collected from August 2021 to May 2022. These forms outlined the support provided by Health Concierges during each interaction. Results: Overall, the program was effective in guiding residents to testing and vaccination services and facilitating COVID-19 safe practices. Nearly two-thirds (191; 63.5%) of the 301 surveyed participants reported speaking with a Health Concierge in the previous six months, and some described having meaningful conversations with them. Despite this, many of the interactions residents described having with Health Concierges were superficial. When considering surveyed participants’ responses to the adapted Public Health Disaster Trust Scale, the mean score across all estates was 2.3 (or slightly more than ‘somewhat confident’) in public health authorities’ ability to respond to a localized infectious disease outbreak. While the program was valued during the rapidly changing public health response, many felt it had failed to evolve in the ‘living with COVID’ phase. Some residents expressed frustration with Health Concierges’ having perceived inactive, passive roles - although other residents felt Health Concierges were helpful and appreciated them. A perception that the true impact of Health Concierges’ work was underrecognized was widely voiced by health staff. All 20,901 Interaction Forms identified COVID-19-related supports provided to residents; almost all included provision of facemasks and/or hand sanitiser and 78% identified additional supports that were also provided, most frequently provision of other health information. Conclusions: The program disseminated up-to-date information to a diverse population within a rapidly changing public health setting. Health Concierges were able promote COVID-19-safe behaviours, including vaccine uptake, and link residents with support services. We recommend the program be revised and continued. New programs that draw on the Health Concierge model may be valuable in supporting future pandemic responses and should be considered in preparedness planning.

Keywords: community health, COVID-19 pandemic, infectious diseases, public health, community health workers

Procedia PDF Downloads 70

Authors: Sanaa Riaz

Abstract:

The free people, Amazigh (plural Imazighen), often known by the more popular exonym, Berber, are spread across several North African countries with the highest population in Morocco have been substantially misunderstood and differentially showcased by entities from western-school educated scholars to human, health and women’s rights organizations, to the State to the international community. This paper is an examination of the various conceptualization of the Imazighen. With the popularity of the Arab Spring movement to oust monarchical and dictatorial rulers across the Middle East and North Africa in Morocco, the Moroccan monarchy introduced various reform programs to win public favor. These included social, economic and educational reforms to incorporate marginalized groups such as the Imazighen. The monarchy has ushered Amazigh representation in public offices and landscape through Amazigh script, even though theirs has been an oral culture. After the Arab Spring, the Justice and Development party, an Islamist party took over in Morocco due to its accessibility to the masses, In Sept. 2021, unlike the case of Egypt and Tunisia where military and constitutional means were sought, Morocco successfully removed it from power through the ballot, resulting in a real victory for the neutral monarchy and its representation as a moderate, secular and liberal force for the nation. As a result, supporting the perpetuation of Amazigh linguistic identity also became synonymous to making a secular statement as a Muslim. It has led to the telling of Amazigh identity at state museums as one representing the indigenous, pure, diverse, culturally-rich and united Morocco. Reform efforts have also prioritized an amiable look towards the economic and familial links of Moroccan Jews with the few thousand families still left in the country and a showcasing through museums and cultural centers of the Jewish identity as Moroccan first. In that endeavor, it is interesting to note the coverage of Jews as the indigenous of Morocco through the embracing of their “folk” cultural and religious practices, those that are not continued outside Morocco. In this epistemology, the concept of the Moroccan Jew becomes similar to the indigenous Amazigh, both cherished as the oldest peoples of Morocco and symbols of its unity and resilience. In the urban discourse, Amazigh identity is a concept that continues to be part of the deliberations of elites and scholars graduating from French schools on the incorporation of rural and illiterate Morocco in economic and educational advancement. Yet, with the constant influx of migrants from Western Sahara into cities like Fez and Marrakesh, Amazigh has often been described as the umbrella term of those of “mixed” ethnic ancestry who constitute the country’s free population. In sum, Amazigh identity highlights the changing discourse on marginalized communities, human rights, representation, Moroccan nationhood, and regional and transnational politics. The aim of this paper is to analyze perceptions of Amazigh identity in Morocco post-2021 ousting of the Islamist party using data from state-sponsored museum displays and cultural centers collected in Summer 2022 and scholarly analyses of Amazigh identity, representation and rights in Morocco.

Keywords: Amazigh identity, Morocco, representation, state politics

Procedia PDF Downloads 70

Authors: Iris Xiaohong Quan, Sharon Qi, Kelly Tianqin Shi

Abstract:

This study focuses on the critical role of insurance policies in a world grappling with increasing mental health challenges, as they significantly influence the dynamics of healthcare businesses and entrepreneurial ventures. The paper utilizes the mental health sector as a case to examine the impact of insurance policies on healthcare service providers, entrepreneurs, and individuals seeking mental health support. This paper addressed the following research questions: To what extent do changes in insurance reimbursement policies affect the accessibility and affordability of mental health services for patients, and how does this impact the overall demand for such services? What are the barriers and opportunities that mental health entrepreneurs face and what strategies and adaptations do mental health businesses employ when navigating the evolving landscape of insurance reimbursement policies? How do changes in insurance reimbursement policies, specifically related to mental health services, influence the financial viability and sustainability of mental health clinics and private practices? Employing a self-designed survey aimed at autism spectrum disorder (ASD) treatment companies, alongside two in-depth case studies and an analysis of pertinent insurance policies and documents, this research aims to elucidate the multifaceted influence of insurance policies on the mental health industry. The findings from this study reveal how insurance policies shape the landscape of mental health businesses and their operations. A total of 821 autism treatment organizations or offices were contacted by telephone between November 1, 2019, and January 31, 2020. About half of the offices (53.33%) were established in the past five years, and 80% were established in the past 15 years. There is a significant increase in the establishment of ABA service centers in the recent two decades as a result of autism insurance reform, the increasing social awareness of ASD, and the redefinition of autism. In addition, almost half of the ABA service providers we surveyed had a patient size ranging from 20 to 50 in the year when the residence state passed the legislation for autism insurance coverage. On average, an ABA service provider works with 5.3 insurance companies. This research find that insurance is the main source of revenue for most ABA service providers. However, our survey reveals that clients’ out of pocket payment has been the second main revenue sources. Despite the changes of regulations and insurance policies in all states, clients still have to pay a fraction of, if not all, the ABA treatment service fees out of pocket. This research shows that some ABA service providers seek federal and government funds and grants to support their services and businesses. Our further analysis with the in-depth case studies and other secondary data also indicate the rise of entrepreneurial startups in the mental health industry. Overall, this research sheds light on both the challenges and opportunities presented by insurance policies in the mental health sector, offering insights into the new industry landscape.

Keywords: entrepreneurship, healthcare policy, insurance policy, mental health industry

Procedia PDF Downloads 40

Authors: Pawel Magryta, Tytus Tulwin, Paweł Karpiński

Abstract:

The ASz62IR engine is a radial aircraft engine with 9 cylinders. This object is produced by the Polish company WSK "PZL-KALISZ" S.A. This is engine is currently being developed by the above company and Lublin University of Technology. In order to provide an effective work of the technological development of this unit it was decided to made the simulation model. The model of ASz-62IR was developed with AVL BOOST software which is a tool dedicated to the one-dimensional modeling of internal combustion engines. This model can be used to calculate parameters of an air and fuel flow in an intake system including charging devices as well as combustion and exhaust flow to the environment. The main purpose of this model is the analysis of the charge exchange and mixture formation in this engine. For this purpose, the model consists of elements such: as air inlet, throttle system, compressor connector, charging compressor, inlet pipes and injectors, outlet pipes, fuel injection and model of fuel mixing and evaporation. The model of charge exchange and mixture formation was based on the model of mass flow rate in intake and exhaust pipes, and also on the calculation of gas properties values like gas constant or thermal capacity. This model was based on the equations to describe isentropic flow. The energy equation to describe flow under steady conditions was transformed into the mass flow equation. In the model the flow coefficient μσ was used, that varies with the stroke/valve opening and was determined in a steady flow state. The geometry of the inlet channels and other key components was mapped with reference to the technical documentation of the engine and empirical measurements of the structure elements. The volume of elements on the charge flow path between the air inlet and the exhaust outlet was measured by the CAD mapping of the structure. Taken from the technical documentation, the original characteristics of the compressor engine was entered into the model. Additionally, the model uses a general model for the transport of chemical compounds of the mixture. There are 7 compounds used, i.e. fuel, O2, N2, CO2, H2O, CO, H2. A gasoline fuel of a calorific value of 43.5 MJ/kg and an air mass fraction for stoichiometric mixture of 14.5 were used. Indirect injection into the intake manifold is used in this model. The model assumes the following simplifications: the mixture is homogenous at the beginning of combustion, accordingly, mixture stoichiometric coefficient A/F remains constant during combustion, combusted and non-combusted charges show identical pressures and temperatures although their compositions change. As a result of the simulation studies based on the model described above, the basic parameters of combustion process, charge exchange, mixture formation in cylinders were obtained. The AVL Boost software is very useful for the piston engine performance simulations. This work has been financed by the Polish National Centre for Research and Development, INNOLOT, under Grant Agreement No. INNOLOT/I/1/NCBR/2013.

Keywords: aviation propulsion, AVL Boost, engine model, charge exchange, mixture formation

Procedia PDF Downloads 295

Authors: Loukou Amoin Marie Djedri

Abstract:

Financing is important for all terrorists – from the largest organizations in control of territories, to the smallest groups – not only for spreading fear through attacks, but also to finance the expansion of terrorist dogmas. These organizations pose serious threats to the international community. The disruption of terrorist financing aims to create a hostile environment for the growth of terrorism and to limit considerably the terrorist groups capacities. The World Bank (WB), together with the International Monetary Fund (IMF), decided to include in their scope the Fight against the money laundering and the financing of terrorism, in order to assist Member States in protecting their internal financial system from terrorism use and abuse and reinforcing their legal system. To do so, they have adopted the Anti-Money Laundering /Combating Financing of Terrorism (AML/CFT) standards that have been set up by the Financial Action Task Force. This set of standards, recognized as the international standards for anti-money laundering and combating the financing of terrorism, has to be implemented by States Members in order to strengthen their judicial system and relevant national institutions. However, we noted that, to date, some States Members still have significant AML/CFT deficiencies, which can constitute serious threats not only to the country’s economic stability but also for the global financial system. In addition, studies stressed out that repressive measures are more implemented by countries than preventive measures, which could be an important weakness in a state security system. Furthermore, we noticed that the AML/CFT standards evolve slowly, while techniques used by terrorist networks keep developing. The goal of the study is to show how to enhance the AML/CFT global compliance through the work of the IMF and the WB, to help member states to consolidate their financial system. To encourage and ensure the effectiveness of these standards, a methodology for assessing the compliance with the AML/CFT standards has been created to follow up the concrete implementation of these standards and to provide accurate technical assistance to countries in need. A risk-based approach has also been adopted as a key component of the implementation of the AML/CFT Standards, with the aim of strengthening the efficiency of the standards. Instead, we noted that the assessment is not efficient in the process of enhancing AML/CFT measures because it seems to lack of adaptation to the country situation. In other words, internal and external factors are not enough taken into account in a country assessment program. The purpose of this paper is to analyze the AML/CFT regime in the fight against the financing of terrorism and to find lasting solutions to achieve the global AML/CFT compliance. The work of all the organizations involved in this combat is imperative to protect the financial network and to lead to the disintegration of terrorist groups in the future.

Keywords: AML/CFT standards, financing of terrorism, international financial institutions, risk-based approach

Procedia PDF Downloads 260

Authors: Magdalena Orth, Gunnar Gotz

Abstract:

Background: Domestic accountability, budget transparency and public financial management (PFM) are considered vital components of good governance in developing countries. The aid modality budget support (BS) promotes these governance functions in developing countries. BS engages in political decision-making and provides financial and technical support to poverty reduction strategies of the partner countries. Nevertheless, many donors have withdrawn their support from this modality due to cases of corruption, fraud or human rights violations. This exit from BS is leaving a finance and governance vacuum in the countries. The evaluation team analyzed the consequences of terminating the use of this modality and found particularly negative effects for good governance outcomes. Methodology: The evaluation uses a qualitative (theory-based) approach consisting of a comparative case study design, which is complemented by a process-tracing approach. For the case studies, the team conducted over 100 semi-structured interviews in Malawi, Uganda, Rwanda and Zambia and used four country-specific, tailor-made budget analysis. In combination with a previous DEval evaluation synthesis on the effects of BS, the team was able to create a before-and-after comparison that yields causal effects. Main Findings: In all four countries domestic accountability and budget transparency declined if other forms of pressure are not replacing BS´s mutual accountability mechanisms. In Malawi a fraud scandal created pressure from the society and from donors so that accountability was improved. In the other countries, these pressure mechanisms were absent so that domestic accountability declined. BS enables donors to actively participate in political processes of the partner country as donors transfer funds into the treasury of the partner country and conduct a high-level political dialogue. The results confirm that the exit from BS created a governance vacuum that, if not compensated through external/internal pressure, leads to a deterioration of good governance. For example, in the case of highly aid dependent Malawi did the possibility of a relaunch of BS provide sufficient incentives to push for governance reforms. Overall the results show that the three good governance areas are negatively affected by the exit from BS. This stands in contrast to positive effects found before the exit. The team concludes that the relationship is causal, because the before-and-after comparison coherently shows that the presence of BS correlates with positive effects and the absence with negative effects. Conclusion: These findings strongly suggest that BS is an effective modality to promote governance and its abolishment is likely to cause governance disruptions. Donors and partner governments should find ways to re-engage in closely coordinated policy-based aid modalities. In addition, a coordinated and carefully managed exit-strategy should be in place before an exit from similar modalities is considered. Particularly a continued framework of mutual accountability and a high-level political dialogue should be aspired to maintain pressure and oversight that is required to achieve good governance.

Keywords: budget support, domestic accountability, public financial management and budget transparency, Sub-Sahara Africa

Procedia PDF Downloads 120

Authors: Amy Claridge, Tishra Beeson

Abstract:

Background: Maternal depression is a serious health concern impacting between 10-16% of birthing persons. It is associated with difficulty in emotional interaction and the formation of attachment bonds between parent and infant. Longitudinally, maternal depression can have severe, lasting impacts on both parent and child, increasing the risk for mental, social, and physical health issues. Rates of prenatal depression have been higher among individuals who were pregnant during the first year of the COVID-19 pandemic. Pregnant persons are considered a high-risk group for poor clinical outcomes from COVID-19 infection and may also have faced or continue to face additional stressors such as financial burdens, loss of income or employment, and the benefits accompanying employment, especially among those in the United States (U.S.). It is less clear whether individuals who gave birth during the pandemic continue to experience high levels of depressive symptoms or whether symptoms have been reduced as a pandemic response has shifted. The current study examined longitudinal reports of depressive symptoms among individuals in the U.S. who gave birth between March 2020 and September 2021. Methods: This mixed-method study involved surveys and interviews with birthing persons (18-45 years old) in their third trimester of pregnancy and at 8 weeks postpartum. Participants also completed a follow-up survey at 12-18 months postpartum. Participants were recruited using convenience methods via an online survey. Survey participants included 242 U.S. women who self-reported depressive symptoms (10-item Edinburgh Postnatal Depression Scale) at each data collection wave. A subset of 23 women participated in semi-structured prenatal and 8-week postpartum qualitative interviews. Follow-up interviews are currently underway and will be integrated into the presentation. Preliminary Results: Prenatal depressive symptoms were significantly positively correlated to 8-week and 12-18-month postpartum depressive symptoms. Participants who reported clinical levels of depression prenatally were 3.29 times (SE = .32, p < .001) more likely to report clinical levels of depression at 18 months postpartum. Those who reported clinical depression at 8-weeks postpartum were 6.52 times (SE = .41, p < .001) more likely to report clinical levels of depression at 18 months postpartum. Participants who gave birth earlier in the pandemic reported significantly higher prenatal (t(103) = 2.84, p < .01) and 8-week postpartum depressive symptoms (t(126) = 3.31, p < .001). Data from qualitative interviews contextualize the findings. Participants reported negative emotions during pregnancy, including sadness, grief, and anxiety. They attributed this in part to their experiences of pregnancy during the pandemic and uncertainty related to the birth experience and postpartum period. Postpartum interviews revealed some stressors specific to childbirth during the COVID-19 pandemic; however, most women reflected on positive experiences of birth and postpartum. Conclusions: Taken together, findings reveal a pattern of persistent depressive symptoms among U.S. parents who gave birth during the pandemic. Depressive symptoms are of significant concern for the health of parents and children, and the findings of this study suggest a need for continued mental health intervention for parents who gave birth during the pandemic. Policy and practice implications will be discussed.

Keywords: maternal mental health, perinatal depression, postpartum depression, covid-19 pandemic

Procedia PDF Downloads 55

Authors: Maari Sugawara

Abstract:

This arts-based research is about "self-torture": the interplay of seemingly opposing elements of pain, pleasure, submission, and power. It asserts that "self-torture" can be considered a nontrivial mediation between the aesthetic and the sociopolitical. It explores what the author calls queered self-torture; "self-torture" marked by an ambivalence that allows the oppressed to resist, and their counter-valorization occasionally functions as therapeutic solutions to the problems they highlight and condense. The research goal is to deconstruct normative self-torture and propose queered self-torture as a fertile ground for considering the complexities of desire that allow the oppressed to practice freedom. While “self-torture” manifests in many societies, this research focuses on cultural and national identity in post-WWII Japan using this lens of self-torture, as masochism functions as the very basis for Japanese cultural and national identity to ensure self-preservation. This masochism is defined as an impulse to realize a sense of pride and construct an identity through the acceptance of subordination, shame, and humiliation in the face of an all-powerful Other; the dominant Euro-America. It could be argued that this self-torture is a result of Japanese cultural annihilation and the trauma of the nation's defeat to the US. This is the definition of "self-torturous thresholds," the author’s post-WWII Japan psycho-historical diagnosis; when this threshold is crossed, the oppressed begin to torture themselves; the oppressors no longer need to do anything to maintain their power. The oppressed are already oppressing themselves. The term "oppressed" here refers to Japanese individuals and residents of Japan who are subjected to oppressive “white” heteropatriarchal supremacist structures and values that serve colonialist interests. There are three stages in "self-torturous thresholds": (1) the oppressors no longer need to oppress because the oppressed voluntarily commit to self-torture; (2) the oppressed find pleasure in self-torture; and (3) the oppressed achieve queered self-torture, to achieve alternative futures. Using the conceptualization of "self-torture," this research examines and critiques pleasure, desire, capital, and power in postwar Japan, which enables the discussion of the data-colonizing “Moonshot Research and Development program”. If the oppressed want to divest from the habits of normative self-torture, which shape what is possible in both our present and future, we need methods to feel and know that the alternative results of self-torture are possible. Phase three will be enacted using Sarah Ahmed's queer methodology to reorient national and cultural identity away from heteronormativity. Through theoretical analysis, textual analysis, archival research, ethnographic interviews, and digital art projects, including experimental documentary as a method to capture the realities of the individuals who are practicing self-torture, this research seeks to reveal how self-torture may become not just a vehicle of pleasure but also a mode of critiquing power and achieving freedom. It seeks to encourage the imaginings of queer Japanese futures, where the marginalized survive Japan’s natural and man-made disasters and Japan’s Imperialist past and present rather than submitting to the country’s continued violence.

Keywords: arts-based research, Japanese studies, interdisciplinary arts, queer studies, cultural studies, popular culture, BDSM, sadomasochism, sexuality, VR, AR, digital art, visual arts, speculative fiction

Procedia PDF Downloads 43

Authors: Emilija Tribocka

Abstract:

This contribution presents parts of an ongoing study of a diachronic relationship between two weak verb classes in Norwegian, the a-class (cf. the paradigm of ‘throw’: kasta – kastar – kasta – kasta) and the e-class (cf. the paradigm of ‘buy’: kjøpa – kjøper – kjøpte – kjøpt). The study investigates inflection class shifts between the two classes with Old Norse, the ancestor of Modern Norwegian, as a starting point. Examination of inflection in 38 verbs in four chosen dialect areas (106 places of attestations) demonstrates that the shifts from the a-class to the e-class are widespread to varying degrees in three out of four investigated areas and are more common than the shifts in the opposite direction. The diachronic productivity of the e-class is unexpected for several reasons. There is general agreement that type frequency is an important factor influencing productivity. The a-class (53% of all weak verbs) was more type frequent in Old Norse than the e-class (42% of all weak verbs). Thus, given the type frequency, the expansion of the e-class is unexpected. Furthermore, in the ‘core’ areas of expanded e-class inflection, the shifts disregard phonological principles creating forms with uncomfortable consonant clusters, e.g., fiskte instead of fiska, the preterit of fiska ‘fish’. Later on, these forms may be contracted, i.e., fiskte > fiste. In this contribution, two factors influencing the shifts are presented: phonological form and token frequency. Verbs with the stem ending in a consonant cluster, particularly when the cluster ends in -t, hardly ever shift to the e-class. As a matter of fact, verbs with this structure belonging to the e-class in Old Norse shift to the a-class in Modern Norwegian, e.g., ON e-class verb skipta ‘change’ shifts to the a-class. This shift occurs as a result of the lack of morpho-phonological transparency between the stem and the preterit suffix of the e-class, -te. As there is a phonological fusion between the stem ending in -t and the suffix beginning in -t, the transparent a-class inflection is chosen. Token frequency plays an important role in the shifts, too, in some dialects. In one of the investigated areas, the most token frequent verbs of the ON e-class remain in the e-class (e.g., høyra ‘hear’, leva ‘live’, kjøpa ‘buy’), while less frequent verbs may shift to the a-class. Furthermore, the results indicate that the shift from the a-class to the e-class occurs in some of the most token frequent verbs of the ON a-class in this area, e.g., lika ‘like’, lova ‘promise’, svara ‘answer’. The latter is unexpected as frequent items tend to remain stable. This study presents a case of unexpected productivity, demonstrating that minor patterns can grow and outdo major patterns. Thus, type frequency is not the only factor that determines productivity. The study addresses the role of phonological form and token frequency in the spread of inflection patterns.

Keywords: inflection class, productivity, token frequency, phonological form

Procedia PDF Downloads 38

Authors: Mohua Dutta

Abstract:

The primary aim of this research paper is to investigate the forced urban migration of Dalits in India who are fleeing caste persecution in rural areas. This paper examines the relationship between caste and rural-to-urban internal migration in India using a literary text, Rohinton Mistry’s A Fine Balance, highlighting the challenges faced by Dalits in rural areas that force them to migrate to urban areas. Despite the prevalence of such discussions in Dalit autobiographies written in vernacular languages, there is a lack of discussion regarding caste migration in Indian English Literature, including this present text, as evidenced by the existing critical interpretations of the novel, which this paper seeks to rectify. The primary research question is how urban migration affects caste system in India and why rural-to-urban caste migration occurs. The purpose of this paper is to better understand the reasons for Dalit migration, the challenges they face in rural and urban areas, and the lingering influence of caste in both rural and urban areas. The study reveals that the promise of mobility and emancipation provided by class operations drives rural-to-urban caste migration in India, but it also reveals that caste marginalization in rural areas is closely linked to class marginalization and other forms of subalternity in urban areas. Moreover, the caste system persists in urban areas as well, making Dalit migrants more vulnerable to social, political, and economic discrimination. The reason for this is that, despite changes in profession and urban migration, the trapped structure of caste capital and family networks exposes migrants to caste and class oppressions. To reach its conclusion, this study employs a variety of methodologies. Discourse analysis is used to investigate the current debates and narratives surrounding caste migration. Critical race theory, specifically intersectional theory and social constructivism, aids in comprehending the complexities of caste, class, and migration. Mistry's novel is subjected to textual analysis in order to identify and interpret references to caste migration. Secondary data, such as theoretical understanding of the caste system in operation and scholarly works on caste migration, are also used to support and strengthen the findings and arguments presented in the paper. The study concludes that rural-to-urban caste migration in India is primarily motivated by the promise of socioeconomic mobility and emancipation offered by urban spaces. However, the caste system persists in urban areas, resulting in the continued marginalisation and discrimination of Dalit migrants. The study also highlights the limitations of urban migration in providing true emancipation for Dalit migrants, as they remain trapped within caste and family network structures. Overall, the study raises awareness of the complexities surrounding caste migration and its impact on the lives of India's marginalised communities. This study contributes to the field of Migration Studies by shedding light on an often-overlooked issue: Dalit migration. It challenges existing literary critical interpretations by emphasising the significance of caste migration in Indian English Literature. The study also emphasises the interconnectedness of caste and class, broadening understanding of how these systems function in both rural and urban areas.

Keywords: rural-to-urban caste migration in india, internal migration in india, caste system in india, dalit movement in india, rooster coop of caste and class, urban poor as subalterns

Procedia PDF Downloads 41

Authors: Christofas Stergianos, Jason Atkin, Herve Morvan

Abstract:

As air traffic increases, more airports are interested in utilizing optimization methods. Many processes happen in parallel at an airport, and complex models are needed in order to have a reliable solution that can be implemented for ground movement operations. The ground movement for aircraft in an airport, allocating a path to each aircraft to follow in order to reach their destination (e.g. runway or gate), is one process that could be optimized. The Quickest Path Problem with Time Windows (QPPTW) algorithm has been developed to provide a conflict-free routing of vehicles and has been applied to routing aircraft around an airport. It was subsequently modified to increase the accuracy for airport applications. These modifications take into consideration specific characteristics of the problem, such as: the pushback process, which considers the extra time that is needed for pushing back an aircraft and turning its engines on; stand holding where any waiting should be allocated to the stand; and runway sequencing, where the sequence of the aircraft that take off is optimized and has to be respected. QPPTW involves searching for the quickest path by expanding the search in all directions, similarly to Dijkstra’s algorithm. Finding a way to direct the expansion can potentially assist the search and achieve a better performance. We have further modified the QPPTW algorithm to use a heuristic approach in order to guide the search. This new algorithm is based on the A-star search method but estimates the remaining time (instead of distance) in order to assess how far the target is. It is important to consider the remaining time that it is needed to reach the target, so that delays that are caused by other aircraft can be part of the optimization method. All of the other characteristics are still considered and time windows are still used in order to route multiple aircraft rather than a single aircraft. In this way the quickest path is found for each aircraft while taking into account the movements of the previously routed aircraft. After running experiments using a week of real aircraft data from Zurich Airport, the new algorithm (A-star QPPTW) was found to route aircraft much more quickly, being especially fast in routing the departing aircraft where pushback delays are significant. On average A-star QPPTW could route a full day (755 to 837 aircraft movements) 56% faster than the original algorithm. In total the routing of a full week of aircraft took only 12 seconds with the new algorithm, 15 seconds faster than the original algorithm. For real time application, the algorithm needs to be very fast, and this speed increase will allow us to add additional features and complexity, allowing further integration with other processes in airports and leading to more optimized and environmentally friendly airports.

Keywords: a-star search, airport operations, ground movement optimization, routing and scheduling

Procedia PDF Downloads 206

Authors: Hanee Ryu

Abstract:

The supporting policies for renewable energy have been designed to deploy renewable energy technology targeting domestic market. The government encourages market creation through obligations such as FIT or RPS on an energy supplier. With these policy measures, the securing vast market needs to induce technology development. Furthermore, it is crucial that ensuring developing market can make the environment nurture the renewable energy industry. Overseas expansion to countries being in demand is essential under immature domestic market. Extending its business abroad can make the domestic company get the knowledge through learning-by-doing. Besides, operation in the countries to be rich in renewable resources such as weather conditions helps to develop proven track record required for verifying technologies. This paper figures out the factor to hamper the global market entry and build up the strategies to overcome difficulties. Survey conducted renewable energy company having overseas experiences at least once. Based on the survey we check the obstacle against exporting home goods and services. As a result, securing funds is salient fact to proceed to business. It is difficult that only private bank or investment agencies participate in the project under uncertainty which renewable energy development project bears inherently. These uncertainties need public fund such as ODA to encourage private sectors to start a business. Furthermore, international organizations such as IRENA or multilateral development banks as WBG play a role to guarantee the investment including risk insurance against uncertainty. It can also manage excavation business cooperating with developing countries and supplement inadequate government funding involved. With survey results strategies to obtain the order, the international organization places are categorized according to the type of getting a contract. This paper suggests 3 types approaching to the international organization project (going through international competitive bidding, using ODA and project financing) and specifies the role of government to support the domestic firms with running out of funds. Under renewable energy industry environment where hard to being created as a spontaneous market, government policy approach needs to motivate the actors to get into the business. It is one of the good strategies that countries with the low demand of renewable energies participate in the project international agencies order in the developing countries having abundant resources. This provides crucial guidance for the formulation of renewable energy development policy and planning with consideration of business opportunities and funding.

Keywords: exporting strategies, multilateral development banks, promoting in developing countries, renewable energy technologies

Procedia PDF Downloads 500

Authors: Domenico Panno, Antonino D’amico, Hamed Jafargholi

Abstract:

This paper presents an experimental analysis of the performance of a system for freezing fish products equipped with a modulating vapour injection scroll compressor operating with R448A refrigerant. Freezing is a critical process for the preservation of seafood products, as it influences quality, food safety, and environmental sustainability. The use of a modulating scroll compressor with vapour injection, associated with the R448A refrigerant, is proposed as a solution to optimize the performance of the system, reducing energy consumption and mitigating the environmental impact. The steam injection modulating scroll compressor represents an advanced technology that allows you to adjust the compressor capacity based on the actual cooling needs of the system. Vapour injection allows the optimization of the refrigeration cycle, reducing the evaporation temperature and improving the overall efficiency of the system. The use of R448A refrigerant, with a low global warming potential (GWP), is part of an environmental sustainability perspective, helping to reduce the climate impact of the system. The aim of this research was to evaluate the performance of the system through a series of experiments conducted on a pilot plant for the freezing of fish products. Several operational variables were monitored and recorded, including evaporation temperature, condensation temperature, energy consumption, and freezing time of seafood products. The results of the experimental analysis highlighted the benefits deriving from the use of the modulating vapour injection scroll compressor with the R448A refrigerant. In particular, a significant reduction in energy consumption was recorded compared to conventional systems. The modulating capacity of the compressor made it possible to adapt the cold production to variations in the thermal load, ensuring optimal operation of the system and reducing energy waste. Furthermore, the use of an electronic expansion valve highlighted greater precision in the control of the evaporation temperature, with minimal deviation from the desired set point. This helped ensure better quality of the final product, reducing the risk of damage due to temperature changes and ensuring uniform freezing of the fish products. The freezing time of seafood has been significantly reduced thanks to the configuration of the entire system, allowing for faster production and greater production capacity of the plant. In conclusion, the use of a modulating vapour injection scroll compressor operating with R448A refrigerant has proven effective in improving the performance of a system for freezing fish products. This technology offers an optimal balance between energy efficiency, temperature control, and environmental sustainability, making it an advantageous choice for food industries.

Keywords: freezing, scroll compressor, energy efficiency, vapour injection

Procedia PDF Downloads 19