Search results for: environmental and social impact assessment

Authors: J. Yang, M. Monnot, T. Eljaddi, L. Simonian, L. Ercolei, P. Moulin

Abstract:

The application of membrane technology to wastewater treatment has expanded rapidly under increasing stringent legislation and environmental protection requirements. At the same time, the water resource is becoming precious, and water reuse has gained popularity. Particularly, ultrafiltration (UF) is a very promising technology for water reuse as it can retain organic matters, suspended solids, colloids, and microorganisms. Nevertheless, few studies dealing with operating optimization of UF as a tertiary treatment for water reuse on a semi-industrial scale appear in the literature. Therefore, this study aims to explore the permeate water quality and to optimize operating parameters (maximizing productivity and minimizing irreversible fouling) through the operation of a UF pilot plant under real conditions. The fully automatic semi-industrial UF pilot plant with periodic classic backwashes (CB) and air backwashes (AB) was set up to filtrate the secondary effluent of an urban wastewater treatment plant (WWTP) in France. In this plant, the secondary treatment consists of a conventional activated sludge process followed by a sedimentation tank. The UF process was thus defined as a tertiary treatment and was operated under constant flux. It is important to note that a combination of CB and chlorinated AB was used for better fouling management. The 200 kDa hollow fiber membrane was used in the UF module, with an initial permeability (for WWTP outlet water) of 600 L·m-2·h⁻¹·bar⁻¹ and a total filtration surface of 9 m². Fifteen filtration conditions with different fluxes, filtration times, and air backwash frequencies were operated for more than 40 hours of each to observe their hydraulic filtration performances. Through comparison, the best sustainable condition was flux at 60 L·h⁻¹·m⁻², filtration time at 60 min, and backwash frequency of 1 AB every 3 CBs. The optimized condition stands out from the others with > 92% water recovery rates, better irreversible fouling control, stable permeability variation, efficient backwash reversibility (80% for CB and 150% for AB), and no chemical washing occurrence in 40h’s filtration. For all tested conditions, the permeate water quality met the water reuse guidelines of the World Health Organization (WHO), French standards, and the regulation of the European Parliament adopted in May 2020, setting minimum requirements for water reuse in agriculture. In permeate: the total suspended solids, biochemical oxygen demand, and turbidity were decreased to < 2 mg·L-1, ≤ 10 mg·L⁻¹, < 0.5 NTU respectively; the Escherichia coli and Enterococci were > 5 log removal reduction, the other required microorganisms’ analysis were below the detection limits. Additionally, because of the COVID-19 pandemic, coronavirus SARS-CoV-2 was measured in raw wastewater of WWTP, UF feed, and UF permeate in November 2020. As a result, the raw wastewater was tested positive above the detection limit but below the quantification limit. Interestingly, the UF feed and UF permeate were tested negative to SARS-CoV-2 by these PCR assays. In summary, this work confirms the great interest in UF as intensified tertiary treatment for water reuse and gives operational indications for future industrial-scale production of reclaimed water.

Keywords: semi-industrial UF pilot plant, water reuse, fouling management, coronavirus

Procedia PDF Downloads 98

Authors: Gasto Lyakurwa, Glory Bakari, Edwin Sabuhoro

Abstract:

Wildlife Management Areas (WMAs) are established to promote and act as a remedy to the protection of wildlife resources outside the core protected area. WMAs aim to address issues of poverty, ensure sustainable use of wildlife resources, and share benefits from wildlife with the member villages. Successfully managed WMA in Tanzania improves local livelihood and conserves local biodiversity through tourism revenues and the protection of wildlife, respectively. Benefits accrued at household levels as a result of conservation activities in WMA can positively influence attitudes towards wildlife conservation. This research intends to assess the positive socio-economic impacts of WMA benefits on households in Burunge WMA in Tanzania. A questionnaire survey was conducted among four randomly selected villages in the ten villages forming the Burunge WMA to explore the household-level benefits of conservation activities. An example of a question item was whether household heads feel that they are benefiting from WMA and if they could remember some of the benefits. Interviews with leaders from WMA and member villages combined the survey to capture aspects of benefit distribution to households. A total of 80 households were used as samples of the recruited study sites. Moreover, the four WMA leaders and the eight village leaders of the respective study villages were interviewed. The study findings revealed that the shared benefit has mostly reached the community level and is less likely to reach the household level. Economic activities such as agriculture and livestock keeping were found to be more important for households than conservation-related economic activities. Conservation-related economic activities generate marginal direct benefits from WMA benefits to households, with ecotourism accounting for only 19.5%. The study also indicates that a direct share of financial benefits from WMA to households is lacking. Wildlife conservation benefits are less likely to reach household levels in WMAs, with the implication of reducing people's conservation attitudes and impeding community conservation success. WMA can utilize the finances from tourism fees and concessions to establish a Community Considerations Bank, which can lend money to some individuals at no or low interest rates. Considering the importance of education and health to households, WMA stands in a good position to provide health insurance premiums and student scholarships to motivate household participation in conservation activities. Community-based organizations and governments responsible for wildlife conservation should create mechanisms to channel conservation benefits to households in order to ensure the achievement of wildlife conservation objectives through WMA. These findings are expected to contribute to forming more WMAs with enhanced mechanisms for sharing conservation benefits to benefit the conservation of natural resources outside of the core protected areas. Motivated households are expected to respect wildlife and are less likely to engage in illegal activities such as poaching and harvesting conserved natural resources while coexisting with wildlife.

Keywords: social economic benefits, individuals, wildlife management areas, biodiversity, community

Procedia PDF Downloads 48

Authors: Sean Vincent

Abstract:

Within the academic community, there is a consensus that political parties in established liberal democracies are facing a myriad of organisational challenges as a result of falling membership, weakening links to grass-roots support and rising voter apathy. During the same period of party decline and growing public disengagement political parties have become increasingly professionalised. The professionalisation of political parties owes much to changes in technology, with television becoming the dominant medium for political communication. In recent years, however, it has become clear that a new medium of communication is becoming utilised by political parties and candidates – New Media. New Media, a term hard to define but related to internet based communication, offers a potential revolution in political communication. It can be utilised by anyone with access to the internet and its most widely used platforms of communication such as Facebook and Twitter, are free to use. The advent of Web 2.0 has dramatically changed what can be done with the Internet. Websites now allow candidates at the constituency level to fundraise, organise and set out personalised policies. Social media allows them to communicate with supporters and potential voters practically cost-free. As such candidate dependency on the national party for resources and image now lies open to debate. Arguing that greater candidate independence may be a natural next step in light of the contemporary challenges faced by parties, this paper examines how New Media is being used by candidates at the constituency level to increase their personal vote. The paper will present findings from research carried out during two elections – the Japanese Lower House election of 2014 and the UK general election of 2015. During these elections a sample of candidates, totalling 150 candidates, from the three biggest parties in each country were selected and their new media output, specifically candidate websites, Twitter and Facebook output subjected to content analysis. The analysis examines how candidates are using new media to both become more functionally, through fundraising and volunteer mobilisation and politically, through the promotion of personal/local policies, independent from the national party. In order to validate the results of content analysis this paper will also present evidence from interviews carried out with 17 candidates that stood in the 2014 Japanese Lower House election or 2015 UK general election. With a combination of statistical analysis and interviews, several conclusions can be made about the use of New Media at constituency level. The findings show not just a clear difference in the way candidates from each country are using New Media but also differences within countries based upon the particular circumstances of each constituency. While it has not yet replaced traditional methods of fundraising and activist mobilisation, New Media is also becoming increasingly important in campaign organisation and the general consensus amongst candidates is that its importance will continue to grow along as politics in both countries becomes more diffuse.

Keywords: political campaigns, elections, new media, political communication

Procedia PDF Downloads 210

Authors: Ashir Ahmed

Abstract:

Peacekeeping is a collective responsibility of governments, law enforcement agencies, communities, families, and individuals. Moreover, the complex nature of peacekeeping activities requires a holistic and collaborative approach where various community sectors work together to form collective strategies that are likely to be more effective than strategies designed and delivered in isolation. Similarly, it is important to learn from past programs to evaluate the initiatives that have worked well and the areas that need further improvement. Review of recent peacekeeping initiatives suggests that there have been tremendous efforts and resources put in place to deal with the emerging threat of terrorism, radicalization and violent extremism through number of de-radicalization programs. Despite various attempts in designing and delivering successful programs for deradicalization, the threat of people being radicalized is growing more than ever before. This research reviews the prominent de-radicalization programs to draw an understanding of their strengths and weaknesses. Some of the weaknesses in the existing programs include. Inaccessibility: Limited resources, geographical location of potential participants (for offline programs), inaccessibility or inability to use various technologies (for online programs) makes it difficult for people to participate in de-radicalization programs. Timeliness: People might need to wait for a program on a set date/time to get the required information and to get their questions answered. This is particularly true for offline programs. Lack of trust: The privacy issues and lack of trust between participants and program organizers are another hurdle in the success of de-radicalization programs. The fear of sharing participants information with organizations (such as law enforcement agencies) without their consent led them not to participate in these programs. Generalizability: Majority of these programs are very generic in nature and do not cater the specific needs of an individual. Participants in these programs may feel that the contents are irrelevant to their individual situations and hence feel disconnected with purpose of the programs. To address the above-mentioned weaknesses, this research developed a framework that recommends some improvements in de-radicalization programs. One of the recommendations is to offer 24/7, secure, private and online hotline (also referred as helpline) for the people who have any question, concern or situation to discuss with someone who is qualified (a counsellor) to deal with people who are vulnerable to be radicalized. To make these hotline services viable and sustainable, the existing organizations offering support for depression, anxiety or suicidal ideation could additionally host these services. These helplines should be available via phone, the internet, social media and in-person. Since these services will be embedded within existing and well-known services, they would likely to get more visibility and promotion. The anonymous and secure conversation between a person and a counsellor would ensure that a person can discuss the issues without being afraid of information sharing with any third party – without his/her consent. The next stage of this project would include the operationalization of the framework by collaborating with other organizations to host de-radicalization hotlines and would assess the effectiveness of such initiatives.

Keywords: de-radicalization, framework, hotlines, peacekeeping

Procedia PDF Downloads 194

Authors: Zafar Tabrez, Nizamuddin Khan

Abstract:

Agriculture in India in the pre-green revolution period was mostly controlled by terrain, climate and edaphic factors. But after the introduction of innovative factors and technological inputs, green revolution occurred and agricultural scene witnessed great change. In the development of India’s agriculture, speedy, and extensive introduction of technological change is one of the crucial factors. The technological change consists of adoption of farming techniques such as use of fertilisers, pesticides and fungicides, improved variety of seeds, modern agricultural implements, improved irrigation facilities, contour bunding for the conservation of moisture and soil, which are developed through research and calculated to bring about diversification and increase of production and greater economic return to the farmers. The green revolution in India took place during late 60s, equipped with technological inputs like high yielding varieties seeds, assured irrigation as well as modern machines and implements. Initially the revolution started in Punjab, Haryana and western Uttar Pradesh. With the efforts of government, agricultural planners, as well as policy makers, the modern technocratic agricultural development scheme was also implemented and introduced in backward and marginal regions of the country later on. Agriculture sector occupies the centre stage of India’s social security and overall economic welfare. The country has attained self-sufficiency in food grain production and also has sufficient buffer stock. Our first Prime Minister, Jawaharlal Nehru said ‘everything else can wait but not agriculture’. There is still a continuous change in the technological inputs and cropping patterns. Keeping these points in view, author attempts to investigate extensively the mechanization of agriculture and the change by selecting western Trans-Ghaghara plain as a case study and block a unit of the study. It includes the districts of Gonda, Balrampur, Bahraich and Shravasti which incorporate 44 blocks. It is based on secondary sources of data by blocks for the year 1997 and 2007. It may be observed that there is a wide range of variations and the change in farm mechanization, i.e., agricultural machineries such as ploughs, wooden and iron, advanced harrow and cultivator, advanced thrasher machine, sprayers, advanced sowing instrument, and tractors etc. It may be further noted that due to continuous decline in size of land holdings and outflux of people for the same nature of works or to be employed in non-agricultural sectors, the magnitude and direction of agricultural systems are affected in the study area which is one of the marginalized regions of Uttar Pradesh, India.

Keywords: agriculture, technological inputs, farm mechanization, food production, cropping pattern

Procedia PDF Downloads 289

Authors: Paola Montenegro, Maria de los Angeles Balaguera Villa

Abstract:

Contraceptive methods play a fundamental role in preventing unwanted pregnancies and protecting users from sexually transmitted infections (STIs). Despite being known to almost the entire population of reproductive age living in Colombia, there are barriers, practices and complex notions about contraceptives that affect their desired mass use and effectiveness. This work aims to analyse some of the perceptions and practices discussed with young people (13-28 years old) living in Colombia regarding the use of contraceptives in their daily lives, preferences, needs and perceived side effects. This research also examines the perceived paradox in autonomy that young people experience regarding contraceptive use: in one hand, its use (or lack of it) is interpreted as an act of self-determination and primary example of reproductive agency, on the other hand, it was frequently associated with coercion and limited autonomy derived from the gaps in reliable information available for young people, the difficulty of accessing certain preferred methods, and sometimes the experienced coercion exercise by doctors, partners and/or family members. The data and analysis discussed in this work stems from a research project whose objective was to provide information about needs and preferences in sexual and reproductive health of young people living in Colombia in relation to a possible telehealth service that could close the gap in access to quality care and safe information. Through a mixed methods approach, this study collected 5.736 responses to a virtual survey disseminated nationwide in Colombia and 47 inperson interviews (24 of them with people who were assigned female at birth and 21 with local key stakeholders in the abortion ecosystem). Quantitative data was analyzed using Stata SE Version 16.0 and qualitative analysis was completed through NVivo using thematic analysis. Key findings on contraception use in young people living in Colombia reveal that 85,8% of participants had used a contraceptive method in the last two years, and that the most commonly used methods were condoms, contraceptive pills, the morning-after pill and the method of interruption. The remaining 14,2% of respondents who declared to not have used contraceptives in the last two years expressed that the main four barriers to access were: "Lack of knowledge about contraceptive methods and where to obtain information and/or access them (13.9%)", "Have had sex with people who have vaginas (10.2%)", "Cost of contraceptive method (8.4%)" and "Difficulties in obtaining medical authorisations (7.6%)". These barriers coincided with the ones used to explain the non-use of contraceptives in young people, which reveals that limitations in information, cost, and quality care represent structural issues that need to be address in programmes, services, and public policy. Finally, interviews showed that young people perceive contraceptive use and non-use as an example of reaffirming reproductive agency and limitations to this can be explained through the widespread incomplete knowledge about how methods work and the prevalence of other social representations of contraception associated with trust, fidelity, and partner preferences, that in the end create limitations to young people’s autonomy.

Keywords: contraception, family planning, premarital fertility, unplanned pregnancy

Procedia PDF Downloads 53

Authors: Ayman Hijazi, Witold Kwapinski, J. J. Leahy

Abstract:

Finding a sustainable alternative energy to fossil fuel is an urgent need as various environmental challenges in the world arise. Therefore, formic acid (FA) decomposition has been an attractive field that lies at the center of biomass platform, comprising a potential pool of hydrogen energy that stands as a new energy vector. Liquid FA features considerable volumetric energy density of 6.4 MJ/L and a specific energy density of 5.3 MJ/Kg that qualifies it in the prime seat as an energy source for transportation infrastructure. Additionally, the increasing research interest in FA decomposition is driven by the need of in-situ H2 production, which plays a key role in the hydrogenation reactions of biomass into higher value components. It is reported elsewhere in literature that catalytic decomposition of FA is usually performed in poorly designed setup using simple glassware under magnetic stirring, thus demanding further energy investment to retain the used catalyst. it work suggests an approach that integrates designing a novel catalyst featuring magnetic property with a robust setup that minimizes experimental & measurement discrepancies. One of the most prominent active species for dehydrogenation/hydrogenation of biomass compounds is palladium. Accordingly, we investigate the potential of engrafting palladium metal onto functionalized magnetic nanoparticles as a heterogeneous catalyst to favor the production of CO-free H2 gas from FA. Using ordinary magnet to collect the spent catalyst renders core-shell magnetic nanoparticles as the backbone of the process. Catalytic experiments were performed in a jacketed batch reactor equipped with an overhead stirrer under inert medium. Through a novel approach, FA is charged into the reactor via high-pressure positive displacement pump at steady state conditions. The produced gas (H2+CO2) was measured by connecting the gas outlet to a measuring system based on the amount of the displaced water. The novelty of this work lies in designing a very responsive catalyst, pumping consistent amount of FA into a sealed reactor running at steady state mild temperatures, and continuous gas measurement, along with collecting the used catalyst without the need for centrifugation. Catalyst characterization using TEM, XRD, SEM, and CHN elemental analyzer provided us with details of catalyst preparation and facilitated new venues to alter the nanostructure of the catalyst framework. Consequently, the introduction of amine groups has led to appreciable improvements in terms of dispersion of the doped metals and eventually attaining nearly complete conversion (100%) of FA after 7 hours. The relative importance of the process parameters such as temperature (35-85°C), stirring speed (150-450rpm), catalyst loading (50-200mgr.), and Pd doping ratio (0.75-1.80wt.%) on gas yield was assessed by a Taguchi design-of-experiment based model. Experimental results showed that operating at lower temperature range (35-50°C) yielded more gas while the catalyst loading and Pd doping wt.% were found to be the most significant factors with a P-values 0.026 & 0.031, respectively.

Keywords: formic acid decomposition, green catalysis, hydrogen, mesoporous silica, process optimization, nanoparticles

Procedia PDF Downloads 32

Authors: Rania Raouf Sedky

Abstract:

Adaptive architecture relates to buildings specifically designed to adapt to their residents and their environments. To design a biologically adaptive system, we can observe how living creatures in nature constantly adapt to different external and internal stimuli to be a great inspiration. The issue is not just how to create a system that is capable of change but also how to find the quality of change and determine the incentive to adapt. The research examines the possibilities of transforming spaces using the human body as an active tool. The research also aims to design and build an effective dynamic structural system that can be applied on an architectural scale and integrate them all into the creation of a new adaptive system that allows us to conceive a new way to design, build and experience architecture in a dynamic manner. The main objective was to address the possibility of a reciprocal transformation between the user and the architectural element so that the architecture can adapt to the user, as the user adapts to architecture. The motivation is the desire to deal with the psychological benefits of an environment that can respond and thus empathize with human emotions through its ability to adapt to the user. Adaptive affiliations of kinematic structures have been discussed in architectural research for more than a decade, and these issues have proven their effectiveness in developing kinematic structures, responsive and adaptive, and their contribution to 'smart architecture'. A wide range of strategies have been used in building complex kinetic and robotic systems mechanisms to achieve convertibility and adaptability in engineering and architecture. One of the main contributions of this research is to explore how the physical environment can change its shape to accommodate different spatial displays based on the movement of the user’s body. The main focus is on the relationship between materials, shape, and interactive control systems. The intention is to develop a scenario where the user can move, and the structure interacts without any physical contact. The soft form of shifting language and interaction control technology will provide new possibilities for enriching human-environmental interactions. How can we imagine a space in which to construct and understand its users through physical gestures, visual expressions, and response accordingly? How can we imagine a space whose interaction depends not only on preprogrammed operations but on real-time feedback from its users? The research also raises some important questions for the future. What would be the appropriate structure to show physical interaction with the dynamic world? This study concludes with a strong belief in the future of responsive motor structures. We imagine that they are developing the current structure and that they will radically change the way spaces are tested. These structures have obvious advantages in terms of energy performance and the ability to adapt to the needs of users. The research highlights the interface between remote sensing and a responsive environment to explore the possibility of an interactive architecture that adapts to and responds to user movements. This study ends with a strong belief in the future of responsive motor structures. We envision that it will improve the current structure and that it will bring a fundamental change to the way in which spaces are tested.

Keywords: adaptive architecture, interactive architecture, responsive architecture, tensegrity

Procedia PDF Downloads 136

Authors: Papazafeiropoulou Olga

Abstract:

The purpose of this paper focuses on exploring the emergence of Greek tragedy on the American stage until the first half of the 20th century through the intellectual processes and contributions of Greek, Italian and Jewish community theatre. Drawing on a wide range of sources, we trace Greek tragedy on the American stage, exploring the intricate processes of community’s theatre identities. The announcement aims to analyze the distinct yet related efforts of first Americans to intersect with Greek tragedy, searching simultaneously for the identities of immigrants. Ultimately, ancient drama became a vehicle not only for great developments in the American theater. In 1903, the Greek actor Dionysios Taboularis arrived in America, while the immigrant stream from Greece to America brought his artistic heritage, presenting in “Hall House” of Chicago the play Return. In 1906, in New York, an amateur group presented the play The Alosi of Messolonghi, and the next year in Chicago, an attempt was noted with a dramatic romance. In the decade 1907-1917, Nikolaos Matsoukas founded and directed the “Arbe theater”, while Petros Kotopoulis formed a troupe. In 1930, one of the greatest Greek theatrical events was the arrival of Marika’s Kotopoulis. Also, members of Vrysoula’s Pantopoulos formed the “Athenian Operetta”, with a positive influence on Greek American theatre. Italian immigrant community, located in tenement “Little Italies” throughout the city, and soon amateur theatrical clubs evolved. The earliest was the “Circolo Filodrammatico Italo-Americano” in 1880. Fausto Malzone’s artistic direction paved the way for the professional Italian immigrant theatre. Immigrant audiences heard the plays of their homeland, representing a major transition for this ethnic theatre. In 1900, the community had produced the major forces that created the professional theatre. By l905, the Italian American theatre had become firmly rooted in its professional phase. Yiddish Theater was both an import and a home-grown phenomenon. In 1878, The Sorceress was brought to America by Boris Thomashefsky. Between 1890 and 1940, many Yiddish theater companies appeared in America, presenting adaptations of classical plays. Αmerica’s people's first encounter with ancient texts was mostly academic. The tracing of tragedy as a form and concept that follows the evolutionary course of domestic social, aesthetic, and political ferments according to the international trends and currents draws conclusions about the early Greek, Italian, and Jewish immigrant’s theatre in relationship to the American scene until the first half of 20th century. Presumably, community theater acquired identity by intersecting with the spiritual reception of tragedy in America.

Keywords: American, community, Greek, Italian, identities, intersection, Jewish, theatre, tragedy

Procedia PDF Downloads 51

Authors: Tak Mau Simon Chan

Abstract:

While there is growing reflection of the adverse impacts instigated by the flourishing gaming industry on the physical health and job satisfaction of those who work in Macau casinos, there is also a critical void in our understanding of the mental health of croupiers and how casino employment interacts with the family system. From a systemic approach, it would be most effective to examine the ‘dealer issues’ collectively and offer assistance to both the individual dealer and the family system of dealers. Therefore, with the use of a mixed method study design, the levels of anxiety, depression and sleeping quality of a sample of 1124 dealers who are working in Macau casinos have been measured in the present study, and 113 dealers have been interviewed about the impacts of casino employment on their family life. This study presents some very important findings. First, the quantitative study indicates that gender is a significant predictor of depression and anxiety levels, whilst lower income means less quality sleep. The Pearson’s correlation coefficients show that as the Zung Self-rating Anxiety Scale (ZSAS) scores increase, the Zung Self-rating Depression Scale (ZSDS) and Pittsburgh Sleep Quality Index (PSQI) scores will also simultaneously increase. Higher income, therefore, might partly explain for the reason why mothers choose to work in the gaming industry even with shift work involved and a stressful work environment. Second, the findings from the qualitative study show that aside from the positive impacts on family finances, the shift work and job stress to some degree negatively affect family responsibilities and relationships. There are resultant family issues, including missed family activities, and reduced parental care and guidance, marital intimacy, and communication with family members. Despite the mixed views on the gender role differences, the respondents generally agree that female dealers have more family and child-minding responsibilities at home, and thus it is more difficult for them to balance work and family. Consequently, they may be more vulnerable to stress at work. Thirdly, there are interrelationships between work and family, which are based on a systemic inquiry that incorporates work- individual- family. Poor physical and psychological health due to shift work or a harmful work environment could affect not just work performance, but also life at home. Therefore, a few practice points about 1) work-family conflicts in Macau; 2) families-in- transition in Macau; and 3) gender and class sensitivity in Macau; are provided for social workers and family practitioners who will greatly benefit these families, especially whose family members are working in the gaming industry in Macau. It is concluded that in addressing the cultural phenomenon of “dealer’s complex” in Macau, a systemic approach is recommended that addresses both personal psychological needs and family issue of dealers.

Keywords: family, work stress, mental health, Macau, dealers, gaming industry

Procedia PDF Downloads 287

Authors: Lolwa Alansari, Abdelhamid Azhaghdani, Sufia Athar, Hanen Mrabet, Annaliza Cruz, Tamara Alshadafat, Almunzer Zakaria

Abstract:

Introduction: Improving the patient experience is a fundamental pillar of healthcare's quadruple aims. Recognizing the importance of patient experiences and perceptions in healthcare interactions is pivotal for driving quality improvement. This abstract centers around the Patient Experience Program, an endeavor crafted with the purpose of comprehending and elevating the experiences of patients in the Obstetrics & Gynecology Emergency Department (OB/GYN ED). Methodology: This comprehensive endeavor unfolded through a structured sequence of phases following Plan-Do-Study-Act (PDSA) model, spanning over 12 months, focused on enhancing patient experiences in the Obstetrics & Gynecology Emergency Department (OB/GYN ED). The study meticulously examined the journeys of patients with acute obstetrics and gynecological conditions, collecting data from over 100 participants monthly. The inclusive approach covered patients of different priority levels (1-5) admitted for acute conditions, with no exclusions. Historical data from March and April 2022 serves as a benchmark for comparison, strengthening causality claims by providing a baseline understanding of OB/GYN ED performance before interventions. Additionally, the methodology includes the incorporation of staff engagement surveys to comprehensively understand the experiences of healthcare professionals with the implemented improvements. Data extraction involved administering open-ended questions and comment sections to gather rich qualitative insights. The survey covered various aspects of the patient journey, including communication, emotional support, timely access to care, care coordination, and patient-centered decision-making. The project's data analysis utilized a mixed-methods approach, combining qualitative techniques to identify recurring themes and extract actionable insights and quantitative methods to assess patient satisfaction scores and relevant metrics over time, facilitating the measurement of intervention impact and longitudinal tracking of changes. From the themes we discovered in both the online and in-person patient experience surveys, several key findings emerged that guided us in initiating improvements, including effective communication and information sharing, providing emotional support and empathy, ensuring timely access to care, fostering care coordination and continuity, and promoting patient-centered decision-making. Results: The project yielded substantial positive outcomes, significantly improving patient experiences in the OB/GYN ED. Patient satisfaction levels rose from 62% to a consistent 98%, with notable improvements in satisfaction with care plan information and physician care. Waiting time satisfaction increased from 68% to a steady 97%. The project positively impacted nurses' and midwives' job satisfaction, increasing from 64% to an impressive 94%. Operational metrics displayed positive trends, including a decrease in the "left without being seen" rate from 3% to 1%, the discharge against medical advice rate dropping from 8% to 1%, and the absconded rate reducing from 3% to 0%. These outcomes underscore the project's effectiveness in enhancing both patient and staff experiences in the healthcare setting. Conclusion: The use of a patient experience questionnaire has been substantiated by evidence-based research as an effective tool for improving the patient experience, guiding interventions, and enhancing overall healthcare quality in the OB/GYN ED. The project's interventions have resulted in a more efficient allocation of resources, reduced hospital stays, and minimized unnecessary resource utilization. This, in turn, contributes to cost savings for the healthcare facility.

Keywords: patient experience, patient survey, person centered care, quality initiatives

Procedia PDF Downloads 46

Authors: Hafsa Memona, Farkhanda Manzoor

Abstract:

Cockroaches are termed as medically important pests because of their wide distribution in human habitation including houses, hospitals, food industries and kitchens. They may harbor multiple drug resistant pathogenic bacteria and protozoan parasites on their external surfaces, disseminate on human food and cause serious diseases and allergies to human. Hence, they are regarded as mechanical vector in human habitation due to their nocturnal activity and nutritional behavior. Viable eggs and dormant cysts of parasites can hitch a ride on cockroaches. Ova and cysts of parasitic organism may settle into the crevices and cracks between thorax and head. There are so many fissures and clefts and crannies on a cockroach which provide site for these organisms. This study aimed with identifying role of cockroaches in mechanically transmitting and disseminating gastrointestinal parasites in two environmental settings; hospitals and houses in urban area of Lahore. Totally, 250 adult cockroaches were collected from houses and hospitals by sticky traps and food baited traps and screened for parasitic load. All cockroaches were captured during their feeding time in natural habitat. Direct wet smear, 1% lugols iodine and modified acid-fast bacilli staining were used to identify the parasites from the body surfaces of cockroaches. Among human habitation two common species of cockroaches were collected i.e. P. americana and B. germanica. The results showed that 112 (46.8%) cockroaches harbored at least one human intestinal parasite on their body surfaces. The cockroaches from hospital environment harboured more parasites than houses. 47 (33.57%) cockroaches from houses and 65 (59.09%) from hospitals were infected with parasitic organisms. Of these, 76 (67.85%) were parasitic protozoans and 36(32.15%) were pathogenic and non-pathogenic intestinal parasites. P. americana harboured more parasites as compared to B. germanica in both environment. Most common human intestinal parasites found on cockroaches include ova of Ascaris lumbricoides (giant roundworm), Trichuris trichura (whipworm), Anchylostoma deodunalae (hookworm), Enterobius vermicularis (pinworm), Taenia spp. and Strongyloides stercoralis (threadworm). The cysts of protozoans’ parasites including Balantidium coli, Entomoeba hystolitica, C. parvum, Isospora belli, Giardia duodenalis and C. cayetenensis were isolated and identified from cockroaches. Both experimental sites were significantly different in carriage of parasitic load on cockroaches. Difference in the hygienic condition of the environments, including human excrement disposal, variable habitat interacted, indoor and outdoor species, may account for the observed variation in the parasitic carriage rate of cockroaches among different experimental site. Thus a finding of this study is that Cockroaches are uniformly distributed in human habitation and act as a mechanical vector of pathogenic parasites that cause common illness such as diarrhea and bowel disorders. This fact contributes to epidemiological chain therefore control of cockroaches will significantly lessen the prevalence of illness in human. Effective control strategies will reduce the public health burden of the gastro-intestinal parasites in the developing countries.

Keywords: cockroaches, health risks, hospitals, houses, parasites, protozoans, transmission

Procedia PDF Downloads 265

Authors: Ana Alvarenga De Castro

Abstract:

Food sovereignty has been brought by the international peasants’ movement, La Via Campesina, as a precondition to food security, speaking about the right of each nation to keep its own supply of foods respecting cultural, sustainable practices and productive diversity. The political conceptualization nowadays goes beyond saying that this term is about achieving the rights of farmers to control the food systems according to local specificities, and about equality in the access to natural resources and quality food. The current feminization of agroecosystems and of food insecurity identified by researchers and recognized by international agencies like the UN and FAO has enhanced the feminist discourse into the food sovereignty movement, considering the historical inequalities that place women farmers in subaltern positions inside the families and rural communities. The current tendency in many rural areas of more women taking responsibility for food production and still facing the lack of access to natural resources meets particular aspects in Latin America due to the global economic logic which places the Global South in the position of raw material supplier for the industrialized North, combined with regional characteristics. In this context, Latin American countries play the role of commodities exporters in the international labor division, including among exported items grains, soybean paste, and ores, to the expense of local food chains which provide domestic quality food supply under more sustainable practices. The connections between gender inequalities and global territorial inequalities related to the access and control of food and natural resources are pointed out by feminist political ecology - FPE - authors, and are linked in this article to the potentialities and limitations of women farmers to reproduce diversified agroecosystems in the tropical environments. The work brings the importance of local practices held by women farmers which are crucial to maintaining sustainable agricultural systems and their results on seeds, soil, biodiversity and water conservation. This work presents an analysis of documents, releases, videos and other publicized experiences launched by some peasants’ organizations in Latin America which evidence the different technical and political answers that meet food sovereignty from peasants’ groups that are attributed to women farmers. They are associated with articles presenting the empirical analysis of women farmers' practices in Latin America. The combination drove to discuss the benefits of peasants' conceptions about food systems and their connections with local realities and the gender issues linked to the food sovereignty conceptualization. Conclusion meets that reality on the field cannot reach food sovereignty's ideal homogeneously and that agricultural sustainable practices are dependent on rights' achievement and social inequalities' eradication.

Keywords: food sovereignty, gender, diversified agricultural systems, access to natural resources

Procedia PDF Downloads 229

Authors: Binbin Chen, Dennis Y. C. Leung

Abstract:

Aluminium (Al) -air cell holds a high volumetric capacity density of 8.05 Ah cm-3, benefit from the trivalence of Al ions. Additional benefits of Al-air cell are low price and environmental friendliness. Furthermore, the Al energy conversion process is characterized of 100% recyclability in theory. Along with a large base of raw material reserve, Al attracts considerable attentions as a promising material to be integrated within the global energy system. However, despite the early successful applications in military services, several problems exist that prevent the Al-air cells from widely civilian use. The most serious issue is the parasitic corrosion of Al when contacts with electrolyte. To overcome this problem, super-pure Al alloyed with various traces of metal elements are used to increase the corrosion resistance. Nevertheless, high-purity Al alloys are costly and require high energy consumption during production process. An alternative approach is to add inexpensive inhibitors directly into the electrolyte. However, such additives would increase the internal ohmic resistance and hamper the cell performance. So far these methods have not provided satisfactory solutions for the problem within Al-air cells. For the operation of alkaline Al-air cell, there are still other minor problems. One of them is the formation of aluminium hydroxide in the electrolyte. This process decreases ionic conductivity of electrolyte. Another one is the carbonation process within the gas diffusion layer of cathode, blocking the porosity of gas diffusion. Both these would hinder the performance of cells. The present work optimizes the above problems by building an Al-air cell operation system, consisting of four components. A top electrolyte tank containing fresh electrolyte is located at a high level, so that it can drive the electrolyte flow by gravity force. A mechanical rechargeable Al-air cell is fabricated with low-cost materials including low grade Al, carbon paper, and PMMA plates. An electrolyte waste tank with elaborate channel is designed to separate the hydrogen generated from the corrosion, which would be collected by gas collection device. In the first section of the research work, we investigated the performance of the mechanical rechargeable Al-air cell with a constant flow rate of electrolyte, to ensure the repeatability experiments. Then the whole system was assembled together and the feasibility of operating was demonstrated. During experiment, pure hydrogen is collected by collection device, which holds potential for various applications. By collecting this by-product, high utilization efficiency of aluminum is achieved. Considering both electricity and hydrogen generated, an overall utilization efficiency of around 90 % or even higher under different working voltages are achieved. Fluidic electrolyte could remove aluminum hydroxide precipitate and solve the electrolyte deterioration problem. This operation system provides a low-cost strategy for harvesting energy from the abundant secondary Al. The system could also be applied into other metal-air cells and is suitable for emergency power supply, power plant and other applications. The low cost feature implies great potential for commercialization. Further optimization, such as scaling up and optimization of fabrication, will help to refine the technology into practical market offerings.

Keywords: aluminium-air cell, high efficiency, hydrogen, mechanical recharge

Procedia PDF Downloads 264

Authors: Heikki Ruohomaa, Vesa Salminen

Abstract:

Regions are facing huge competition to attract companies, businesses, inhabitants, students, etc. This way to improve living and business environment, which is rapidly changing due to digitalization. On the other hand, from the industry's point of view, the availability of a skilled labor force and an innovative environment are crucial factors. In this context, qualified staff has been seen to utilize the opportunities of digitalization and respond to the needs of future skills. World Manufacturing Forum has stated in the year 2019- report that in next five years, 40% of workers have to change their core competencies. Through digital transformation, new technologies like cloud, mobile, big data, 5G- infrastructure, platform- technology, data- analysis, and social networks with increasing intelligence and automation, enterprises can capitalize on new opportunities and optimize existing operations to achieve significant business improvement. Digitalization will be an important part of the everyday life of citizens and present in the working day of the average citizen and employee in the future. For that reason, the education system and education programs on all levels of education from diaper age to doctorate have been directed to fulfill this ecosystem strategy. Goal: The Fourth Industrial Revolution will bring unprecedented change to societies, education organizations and business environments. This article aims to identify how education, education content, the way education has proceeded, and overall whole the education business is changing. Most important is how we should respond to this inevitable co- evolution. Methodology: The study aims to verify how the learning process is boosted by new digital content, new learning software and tools, and customer-oriented learning environments. The change of education programs and individual education modules can be supported by applied research projects. You can use them in making proof- of- the concept of new technology, new ways to teach and train, and through the experiences gathered change education content, way to educate and finally education business as a whole. Major findings: Applied research projects can prove the concept- phases on real environment field labs to test technology opportunities and new tools for training purposes. Customer-oriented applied research projects are also excellent for students to make assignments and use new knowledge and content and teachers to test new tools and create new ways to educate. New content and problem-based learning are used in future education modules. This article introduces some case study experiences on customer-oriented digital transformation projects and how gathered knowledge on new digital content and a new way to educate has influenced education. The case study is related to experiences of research projects, customer-oriented field labs/learning environments and education programs of Häme University of Applied Sciences.

Keywords: education process, digitalization content, digital tools for education, learning environments, transdisciplinary co-operation

Procedia PDF Downloads 162

Authors: Sabina Huč, Staffan Svensson, Tomaž Hozjan

Abstract:

Timber structures may be exposed to various environmental conditions during their service life. Often, the structures have to resist extreme changes in the relative humidity of surrounding air, with simultaneously carrying the loads. Wood material response for this load case is seen as increasing deformation of the timber structure. Relative humidity variations cause moisture changes in timber and consequently shrinkage and swelling of the material. Moisture changes and loads acting together result in mechano-sorptive creep, while sustained load gives viscoelastic creep. In some cases, magnitude of the mechano-sorptive strain can be about five times the elastic strain already at low stress levels. Therefore, analyzing mechano-sorptive creep and its influence on timber structures’ long-term behavior is of high importance. Relatively many one-dimensional rheological models for rheological behavior of wood can be found in literature, while a number of models coupling creep response in each material direction is limited. In this study, mathematical formulation of a coupled two-dimensional mechano-sorptive model and its application to the experimental results are presented. The mechano-sorptive model constitutes of a moisture transport model and a mechanical model. Variation of the moisture content in wood is modelled by multi-Fickian moisture transport model. The model accounts for processes of the bound-water and water-vapor diffusion in wood, that are coupled through sorption hysteresis. Sorption defines a nonlinear relation between moisture content and relative humidity. Multi-Fickian moisture transport model is able to accurately predict unique, non-uniform moisture content field within the timber member over time. Calculated moisture content in timber members is used as an input to the mechanical analysis. In the mechanical analysis, the total strain is assumed to be a sum of the elastic strain, viscoelastic strain, mechano-sorptive strain, and strain due to shrinkage and swelling. Mechano-sorptive response is modelled by so-called spring-dashpot type of a model, that proved to be suitable for describing creep of wood. Mechano-sorptive strain is dependent on change of moisture content. The model includes mechano-sorptive material parameters that have to be calibrated to the experimental results. The calibration is made to the experiments carried out on wooden blocks subjected to uniaxial compressive loaded in tangential direction and varying humidity conditions. The moisture and the mechanical model are implemented in a finite element software. The calibration procedure gives the required, distinctive set of mechano-sorptive material parameters. The analysis shows that mechano-sorptive strain in transverse direction is present, though its magnitude and variation are substantially lower than the mechano-sorptive strain in the direction of loading. The presented mechano-sorptive model enables observing real temporal and spatial distribution of the moisture-induced strains and stresses in timber members. Since the model’s suitability for predicting mechano-sorptive strains is shown and the required material parameters are obtained, a comprehensive advanced analysis of the stress-strain state in timber structures, including connections subjected to constant load and varying humidity is possible.

Keywords: mechanical analysis, mechano-sorptive creep, moisture transport model, timber

Procedia PDF Downloads 228

Authors: I. Derek Kaka’an, P. Smolianov, D. Koh Choon Lian, S. Dion, C. Schoen, J. Norberg

Abstract:

This study was designed to examine mass participation and elite football performance in Nigeria with reference to advance international football management practices. Over 200 sources of literature on sport delivery systems were analyzed to construct a globally applicable model of elite football integrated with mass participation, comprising of the following three levels: macro- (socio-economic, cultural, legislative, and organizational), meso- (infrastructures, personnel, and services enabling sport programs) and micro-level (operations, processes, and methodologies for development of individual athletes). The model has received scholarly validation and showed to be a framework for program analysis that is not culturally bound. The Smolianov and Zakus model has been employed for further understanding of sport systems such as US soccer, US Rugby, swimming, tennis, and volleyball as well as Russian and Dutch swimming. A questionnaire was developed using the above-mentioned model. Survey questions were validated by 12 experts including academicians, executives from sport governing bodies, football coaches, and administrators. To identify best practices and determine areas for improvement of football in Nigeria, 120 coaches completed the questionnaire. Useful exemplars and possible improvements were further identified through semi-structured discussions with 10 Nigerian football administrators and experts. Finally, content analysis of Nigeria Football Federation’s website and organizational documentation was conducted. This paper focuses on the meso-level of Nigerian football delivery, particularly infrastructures, personnel, and services enabling sport programs. This includes training centers, competition systems, and intellectual services. Results identified remarkable achievements coupled with great potential to further develop football in different types of public and private organizations in Nigeria. These include: assimilating football competitions with other cultural and educational activities, providing favorable conditions for employees of all possible organizations to partake and help in managing football programs and events, providing football coaching integrated with counseling for prevention of antisocial conduct, and improving cooperation between football programs and organizations for peace-making and advancement of international relations, tourism, and socio-economic development. Accurate reporting of the sports programs from the media should be encouraged through staff training for better awareness of various events. The systematic integration of these meso-level practices into the balanced development of mass and high-performance football will contribute to international sport success as well as national health, education, and social harmony.

Keywords: football, high performance, mass participation, Nigeria, sport development

Procedia PDF Downloads 229

Authors: Iñaki Milton-Laskibar, Leixuri Aguirre, Maria P. Portillo

Abstract:

Introduction: Energy restriction is an effective approach in preventing liver steatosis. However, due to social and economic reasons among others, compliance with this treatment protocol is often very poor, especially in the long term. Resveratrol, a natural polyphenolic compound that belongs to stilbene group, has been widely reported to imitate the effects of energy restriction. Objective: To analyze the effects of resveratrol under normoenergetic feeding conditions and under a mild energy restriction on liver fat accumulation and hepatic fatty acid oxidation. Methods: 36 male six-week-old rats were fed a high-fat high-sucrose diet for 6 weeks in order to induce steatosis. Then, rats were divided into four groups and fed a standard diet for 6 additional weeks: control group (C), resveratrol group (RSV, resveratrol 30 mg/kg/d), restricted group (R, 15 % energy restriction) and combined group (RR, 15 % energy restriction and resveratrol 30 mg/kg/d). Liver triacylglycerols (TG) and total cholesterol contents were measured by using commercial kits. Carnitine palmitoyl transferase 1a (CPT 1a) and citrate synthase (CS) activities were measured spectrophotometrically. TFAM (mitochondrial transcription factor A) and peroxisome proliferator-activator receptor alpha (PPARα) protein contents, as well as the ratio acetylated peroxisome proliferator-activated receptor gamma coactivator 1-alpha (PGC1α)/Total PGC1α were analyzed by Western blot. Statistical analysis was performed by using one way ANOVA and Newman-Keuls as post-hoc test. Results: No differences were observed among the four groups regarding liver weight and cholesterol content, but the three treated groups showed reduced TG when compared to the control group, being the restricted groups the ones showing the lowest values (with no differences between them). Higher CPT 1a and CS activities were observed in the groups supplemented with resveratrol (RSV and RR), with no difference between them. The acetylated PGC1α /total PGC1α ratio was lower in the treated groups (RSV, R and RR) than in the control group, with no differences among them. As far as TFAM protein expression is concerned, only the RR group reached a higher value. Finally, no changes were observed in PPARα protein expression. Conclusions: Resveratrol administration is an effective intervention for liver triacylglycerol content reduction, but a mild energy restriction is even more effective. The mechanisms of action of these two strategies are different. Thus resveratrol, but not energy restriction, seems to act by increasing fatty acid oxidation, although mitochondriogenesis seems not to be induced. When both treatments (resveratrol administration and a mild energy restriction) were combined, no additive or synergic effects were appreciated. Acknowledgements: MINECO-FEDER (AGL2015-65719-R), Basque Government (IT-572-13), University of the Basque Country (ELDUNANOTEK UFI11/32), Institut of Health Carlos III (CIBERobn). Iñaki Milton is a fellowship from the Basque Government.

Keywords: energy restriction, fat, liver, oxidation, resveratrol

Procedia PDF Downloads 199

Authors: Colin S. Chen, Chien-Jung Tien, Hsin-Jan Huang

Abstract:

For weathering studies, the change of chemical constituents by biodegradation effect in diesel-contaminated soils are important factors to be considered, especially when there is a prolonged period of weathering processes. The objective was to evaluate biodegradation effects onto hydrocarbon fingerprinting and distribution patterns of diesel fuels, fuel source screening and differentiation, source-specific marker compounds, and diagnostic ratios of diesel fuel constituents by laboratory and field studies. Biodegradation processes of diesel contaminated soils were evaluated by experiments lasting for 15 and 12 months, respectively. The degradation of diesel fuel in top soils was affected by organic carbon content and biomass of microorganisms in soils. Higher depletion of total petroleum hydrocarbon (TPH), n-alkanes, and polynuclear aromatic hydrocarbons (PAHs) and their alkyl homologues was observed in soils containing higher organic carbon content and biomass. Decreased ratio of selected isoprenoids (i.e., pristane (Pr) and phytane (Ph)) including n-C17/pristane and n-C18/phytane was observed. The ratio of pristane/phytane was remained consistent for a longer period of time. At the end of the experimental period, a decrease of pristane/phytane was observed. Biomarker compounds of bicyclic sesquiterpanes (BS) were less susceptible to the effects of biodegradation. The ratios of characteristic factors such as C15 sesquiterpane/ 8β(H)-drimane (BS3/BS5), C15 sesquiterpane/ 8β(H)-drimane (BS4/BS5), 8β(H)-drimane/8β(H)-homodrimane (BS5/BS10), and C15 sesquiterpane/8β(H)-homodrimane (BS3/BS10) could be adopted for source identification of diesel fuels in top soil. However, for biodegradation processes lasted for six months but shorter than nine months, only BS3/BS5 and BS3/BS10 could be distinguished in two diesel fuels. In subsoil experiments (contaminated soil located 50 cm below), the ratios of characteristic factors including BS3/BS5, BS4/BS5, and BS5/BS10 were valid for source identification of two diesel fuels for nine month biodegradation. At the early stage of contamination, biomass of soil decreased significantly. However, 6 and 7 dominant species were found in soils in top soil experiments, respectively. With less oxygen and nutrients in subsoil, less biomass of microorganisms was observed in subsoils. Only 2 and 4 diesel-degrading species of microorganisms were identified in two soils, respectively. Parameters of double ratio such as fluorene/C1-fluorene: C2-phenanthrene/C3-phenanthrene (C0F/C1F:C2P/C3P) in both top and subsoil, C2-naphthalene/C2-phenanthrene: C1-phenanthrene/C3-phenanthrene (C2N/C2P:C1P/C3P), and C1-phenanthrene/C1-fluorene: C3-naphthalene/C3-phenanthrene (C1P/C1F:C3N/C3P) in subsoil could serve as forensic indicators in diesel contaminated sites. BS3/BS10:BS4/BS5 could be used in 6 to 9 months of biodegradation processes. Results of principal component analysis (PCA) indicated that source identification of diesel fuels in top soil could only be perofrmed for weathering process less than 6 months. For subsoil, identification can be conducted for weathering process less than 9 months. Ratio of isoprenoids (pristane and phytane) and PAHs might be affected by biodegradation in spilled sites. The ratios of bicyclic sesquiterpanes could serve as forensic indicators in diesel-contaminated soils. Finally, source identification was attemped for samples collected from different fuel contaminated sites by using the unique pattern of sesquiterpanes. It was anticipated that the information generated from this study would be adopted by decision makers to evaluate the liability of cleanup in diesel contaminated sites.

Keywords: biodegradation, diagnostic ratio, diesel fuel, environmental forensics

Procedia PDF Downloads 201

Authors: Ramiz M. Shubbar, Dong In Lee, Hatem A. Gzar, Arthur S. Rood

Abstract:

Air pollution is one of the biggest environmental problems in Baghdad, Iraq. The Daura refinery located nearest the center of Baghdad, represents the largest industrial area, which transmits enormous amounts of pollutants, therefore study the gaseous pollutants and particulate matter are very important to the environment and the health of the workers in refinery and the people whom leaving in areas around the refinery. Actually, some studies investigated the studied area before, but it depended on the basic Gaussian equation in a simple computer programs, however, that kind of work at that time is very useful and important, but during the last two decades new largest production units were added to the Daura refinery such as, PU_3 (Power unit_3 (Boiler 11&12)), CDU_1 (Crude Distillation unit_70000 barrel_1), and CDU_2 (Crude Distillation unit_70000 barrel_2). Therefore, it is necessary to use new advanced model to study air pollution at the region for the new current years, and calculation the monthly emission rate of pollutants through actual amounts of fuel which consumed in production unit, this may be lead to accurate concentration values of pollutants and the behavior of dispersion or transport in study area. In this study to the best of author’s knowledge CALPUFF model was used and examined for first time in Iraq. CALPUFF is an advanced non-steady-state meteorological and air quality modeling system, was applied to investigate the pollutants concentration of SO2, NO2, CO, and PM1-10μm, at areas adjacent to Daura refinery which located in the center of Baghdad in Iraq. The CALPUFF modeling system includes three main components: CALMET is a diagnostic 3-dimensional meteorological model, CALPUFF (an air quality dispersion model), CALPOST is a post processing package, and an extensive set of preprocessing programs produced to interface the model to standard routinely available meteorological and geophysical datasets. The targets of this work are modeling and simulation the four pollutants (SO2, NO2, CO, and PM1-10μm) which emitted from Daura refinery within one year. Emission rates of these pollutants were calculated for twelve units includes thirty plants, and 35 stacks by using monthly average of the fuel amount consumption at this production units. Assess the performance of CALPUFF model in this study and detect if it is appropriate and get out predictions of good accuracy compared with available pollutants observation. CALPUFF model was investigated at three stability classes (stable, neutral, and unstable) to indicate the dispersion of the pollutants within deferent meteorological conditions. The simulation of the CALPUFF model showed the deferent kind of dispersion of these pollutants in this region depends on the stability conditions and the environment of the study area, monthly, and annual averages of pollutants were applied to view the dispersion of pollutants in the contour maps. High values of pollutants were noticed in this area, therefore this study recommends to more investigate and analyze of the pollutants, reducing the emission rate of pollutants by using modern techniques and natural gas, increasing the stack height of units, and increasing the exit gas velocity from stacks.

Keywords: CALPUFF, daura refinery, Iraq, pollutants

Procedia PDF Downloads 179

Authors: Juliana Chiarini Balbino Fernandes

Abstract:

This article aims to investigate the Spanish didactic book, entitled ‘El Calculo y La Medida en El Primer Grado de La Escuela Decroly’, written by Dr. O. Decroly and A. Hamaide, published in Madrid, in the year 1934. In addition to analyzing how mathematical knowledge is present in the proposed Centers of Interest. The textbooks, in addition to pedagogical tools, reflect a certain moment in society and allow the analysis of the theoretical-methodological proposal that can be implemented by the teacher. The study proposed here will be carried out by the lens of Cultural History, supported by Roger Chartier (1991) and by the concepts on textbooks, based on Alain Choppin (2004). The textbook selected for this study exposes a program of ideas associated with the method of Centers of Interest and arithmetic is linked to these interests. In the first courses (six to eight years), most centers can be considered to correspond to occasional calls, as they take advantage of events that arise spontaneously to work with observation, measurement, association and expression exercises. The program of ideas associated with Centers of Interest addresses the biological and social aspects of children, as long as they can express their needs for activities and games, satisfying the natural curiosity. Still, the program of associated ideas offers occasions for problems whose data are taken in observation exercises and concrete expressions (manuals, drawings). In the method applied at the school of L'Ermitage, school created by Decroly in Belgium in 1907, observation, is the basis of each center of interest. It offers the chance to compare and measure. To observe is more than to perceive; it is also to establish relations between the graded aspects of the same object, to seek relations between different intensities; is to verify successions, special and temporary relationships; is to make comparisons, to notice differences and similarities in block or datable (analysis), is to establish a bridge between the world and the thought. To make the observation more precise, it is important to compare, measure, and resort to considered objects as natural units of measure. Measurement and calculation are, therefore, quite naturally subject to observation. Thus, it is possible to make the child enter into the interest in the calculation, linking it to the observation. It was observed that the Centers of Interest, according to Decroly, should respond to the concerns and attend to the motivations of the students and the teaching of arithmetical must obey a logical seriation, considering the interest and the experience of the children. The teaching of arithmetical should not be limited to the schedule, it should cover every quantitative aspect that arises in the other disciplines. The feeling of unity is established in observation, association and expression, which coordinate a whole program of cultural activities, concentrating it around a central idea.

Keywords: didactic book, centers of interest, mathematical knowledge, primary education

Procedia PDF Downloads 93

Authors: Andreas Kerstan, Darren Robey, Wesam Alvan, David Troiani

Abstract:

Over the last 3.5 years, Quantum Cascade Lasers (QCL) technology has become increasingly important in infrared (IR) microscopy. The advantages over fourier transform infrared (FTIR) are that large areas of a few square centimeters can be measured in minutes and that the light intensive QCL makes it possible to obtain spectra with excellent S/N, even with just one scan. A firmly established solution of the laser direct infrared imaging (LDIR) 8700 is the analysis of microplastics. The presence of microplastics in the environment, drinking water, and food chains is gaining significant public interest. To study their presence, rapid and reliable characterization of microplastic particles is essential. Significant technical hurdles in microplastic analysis stem from the sheer number of particles to be analyzed in each sample. Total particle counts of several thousand are common in environmental samples, while well-treated bottled drinking water may contain relatively few. While visual microscopy has been used extensively, it is prone to operator error and bias and is limited to particles larger than 300 µm. As a result, vibrational spectroscopic techniques such as Raman and FTIR microscopy have become more popular, however, they are time-consuming. There is a demand for rapid and highly automated techniques to measure particle count size and provide high-quality polymer identification. Analysis directly on the filter that often forms the last stage in sample preparation is highly desirable as, by removing a sample preparation step it can both improve laboratory efficiency and decrease opportunities for error. Recent advances in infrared micro-spectroscopy combining a QCL with scanning optics have created a new paradigm, LDIR. It offers improved speed of analysis as well as high levels of automation. Its mode of operation, however, requires an IR reflective background, and this has, to date, limited the ability to perform direct “on-filter” analysis. This study explores the potential to combine the filter with an infrared reflective surface filter. By combining an IR reflective material or coating on a filter membrane with advanced image analysis and detection algorithms, it is demonstrated that such filters can indeed be used in this way. Vibrational spectroscopic techniques play a vital role in the investigation and understanding of microplastics in the environment and food chain. While vibrational spectroscopy is widely deployed, improvements and novel innovations in these techniques that can increase the speed of analysis and ease of use can provide pathways to higher testing rates and, hence, improved understanding of the impacts of microplastics in the environment. Due to its capability to measure large areas in minutes, its speed, degree of automation and excellent S/N, the LDIR could also implemented for various other samples like food adulteration, coatings, laminates, fabrics, textiles and tissues. This presentation will highlight a few of them and focus on the benefits of the LDIR vs classical techniques.

Keywords: QCL, automation, microplastics, tissues, infrared, speed

Procedia PDF Downloads 49

Authors: Angela O. Ugwu, Sunday Ocheni

Abstract:

Background: Cancer-associated thrombosis (CAT) is a cause of morbidity and mortality among cancer patients. Several risk factors for developing venous thromboembolism (VTE) also coexist with cancer patients, such as chemotherapy and immobilization, thus contributing to the higher risk of VTE in cancer patients when compared to non-cancer patients. This study aimed to determine if there is any correlation between levels of some inflammatory cytokines/haematological parameters and Khorana scores of newly diagnosed chemotherapy naïve ambulatory cancer patients (CNACP). Methods: This was a cross-sectional analytical study carried out from June 2021 to May 2022. Eligible newly diagnosed cancer patients 18 years and above (case group) were enrolled consecutively from the adult Oncology Clinics of the University of Nigeria Teaching Hospital, Ituku/Ozalla (UNTH). The control group was blood donors at UNTH Ituku/Ozalla, Enugu blood bank, and healthy members of the Medical and Dental Consultants Association of Nigeria (MDCAN), UNTH Chapter. Blood samples collected from the participants were assayed for IL-6, TNF-Alpha, and haematological parameters such as haemoglobin, white blood cell count (WBC), and platelet count. Data were entered into an Excel worksheet and were then analyzed using Statistical Package for Social Sciences (SPSS) computer software version 21.0 for windows. A P value of < 0.05 was considered statistically significant. Results: A total of 200 participants (100 cases and 100 controls) were included in the study. The overall mean age of the participants was 47.42 ±15.1 (range 20-76). The sociodemographic characteristics of the two groups, including age, sex, educational level, body mass index (BMI), and occupation, were similar (P > 0.05). Following One Way ANOVA, there were significant differences between the mean levels of interleukin-6 (IL-6) (p = 0.036) and tumor necrotic factor-α (TNF-α) (p = 0.001) in the three Khorana score groups of the case group. Pearson’s correlation analysis showed a significant positive correlation between the Khorana scores and IL-6 (r=0.28, p = 0.031), TNF-α (r= 0.254, p= 0.011), and PLR (r= 0.240, p=0.016). The mean serum levels of IL-6 were significantly higher in CNACP than in the healthy controls [8.98 (8-12) pg/ml vs. 8.43 (2-10) pg/ml, P=0.0005]. There were also significant differences in the mean levels of the haemoglobin (Hb) level (P < 0.001)); white blood cell (WBC) count ((P < 0.001), and platelet (PL) count (P = 0.005) between the two groups of participants. Conclusion: There is a significant positive correlation between the serum levels of IL-6, TNF-α, and PLR and the Khorana scores of CNACP. The mean serum levels of IL-6, TNF-α, PLR, WBC, and PL count were significantly higher in CNACP than in the healthy controls. Ambulatory cancer patients with high-risk Khorana scores may benefit from anti-inflammatory drugs because of the positive correlation with inflammatory cytokines. Recommendations: Ambulatory cancer patients with 2 Khorana scores may benefit from thromboprophylaxis since they have higher Khorana scores. A multicenter study with a heterogeneous population and larger sample size is recommended in the future to further elucidate the relationship between IL-6, TNF-α, PLR, and the Khorana scores among cancer patients in the Nigerian population.

Keywords: thromboprophylaxis, cancer, Khorana scores, inflammatory cytokines, haematological parameters

Procedia PDF Downloads 65

Authors: Simone Raimondi De Souza, Glaucia Maria Moraes De Oliveira, Ronir Raggio Luiz, Glorimar Rosa

Abstract:

Introduction: Obesity is among the main risk factors for cardiovascular disease (CVD). Genesis is multifactorial, including genetic, hormonal and environmental factors disorders, among which inadequate feeding pattern, for which nutritional counseling strategies have proven effective. The consumption of beta-glucans (soluble fibers that reportedly promote satiety) present in oat bran can be an effective strategy for preventing and treating obesity. Other benefits have been observed with oat bran consumption, such as reduction of hypercholesterolemia and hyperglycemia, two other risk factors for CVD. Objectives: To analyze the effect of oat bran consumption associated with nutritional counseling in reducing body mass index (BMI), blood cholesterol, glucose profile, waist and neck circumference in obese individuals, and to evaluate the change in eating pattern. Methods: clinical trial, randomized, double-blind, placebo-controlled, lasting 90 days with adults of both genders, with BMI ≥30kg/m2. The study was approved by the Ethics in Research involving human beings in a public institute of cardiology, in Rio de Janeiro, Brazil. Individuals were invited to participate and accepted formally by signing the Terms of Consent. Participants were randomized into oat bran group (gOB) or placebo group (gPCB) and received, respectively: morning prepared consisting of 40g oat bran, 30g of skimmed milk powder and 1g sweetener sucralose; refined flour 40g rice, 30g of milk powder and 1g sweetener sucralose. The Ten Steps to Healthy Eating, of Brazilian Ministry of Health were used to support the nutritional counseling. Variables analyzed: gender; age; BMI, waist circumference (WC) neck circumference (NC); systolic blood pressure (SBP); diastolic blood pressure (DBP); food consumption, total cholesterol (TC), LDL-cholesterol (LDL-c), HDL-cholesterol (HDL-c), non-HDL cholesterol (nHDLc), triglycerides (TG), fasting glucose (FG), fasting insulin (FI) and HOMA-IR. Dietary intake was assessed by 24-hour dietary recall. The Diet Quality Index revised for the Brazilian population (IQD-R) assessed quality of feeding pattern. Statistical analyzes were performed using SPSS version 21, considering statistically significant p-value less than 0.05. Results: A total of 38 participants were included, age = 50 ± 7,6years, 63% women. 19 subjects were placed in gOB and 19 in gPCB. After intervention, statistically significant reductions were observed in the following parameters: in gOB: IQD-R, TC, LDL-c, nHDL-c, FI, SBP, DBP, BMI, WC, NC; in gPCB: IQD-R, LDL-c, SBP, DBP, BMI, WC, NC. No statistically significant differences were observed in the results between groups. Conclusion: Our results reinforce nutritional counseling as important strategy for prevention and treatment of obesity and suggest that inclusion of oat bran in daily diet can bring additional benefits controlling risk factors for CVD. More studies are needed to establish all benefits of oat bran to human health as well as the ideal daily dose for consumption.

Keywords: oat bran, cardiovascular disease, nutritional counseling, obesity

Procedia PDF Downloads 207

Authors: Kuan Lun Pan, Moo Been Chang

Abstract:

Volatile organic compounds (VOCs) are one of major air contaminants, and they can react with nitrogen oxides (NOx) in atmosphere to form ozone (O3) and peroxyacetyl nitrate (PAN) with solar irradiation, leading to environmental hazards. In addition, some VOCs are toxic at low concentration levels and cause adverse effects on human health. How to effectively reduce VOCs emission has become an important issue. Thermal catalysis is regarded as an effective way for VOCs removal because it provides oxidation route to successfully convert VOCs into carbon dioxide (CO2) and water (H2O(g)). Single perovskite-type catalysts are promising for VOC removal, and they are of good potential to replace noble metals due to good activity and high thermal stability. Single perovskites can be generally described as ABO3 or A2BO4, where A-site is often a rare earth element or an alkaline. Typically, the B-site is transition metal cation (Fe, Cu, Ni, Co, or Mn). Catalytic properties of perovskites mainly rely on nature, oxidation states and arrangement of B-site cation. Interestingly, single perovskites could be further synthesized to form double perovskite-type catalysts which can simply be represented by A2B’B”O6. Likewise, A-site stands for an alkaline metal or rare earth element, and the B′ and B′′ are transition metals. Double perovskites possess unique surface properties. In structure, three-dimensional of B-site with ordered arrangement of B’O6 and B”O6 is presented alternately, and they corner-share octahedral along three directions of the crystal lattice, while cations of A-site position between the void of octahedral. It has attracted considerable attention due to specific arrangement of alternating B-site structure. Therefore, double perovskites may have more variations than single perovskites, and this greater variation may promote catalytic performance. It is expected that activity of double perovskites is higher than that of single perovskites toward VOC removal. In this study, double perovskite-type catalyst (La2CoMnO6) is prepared and evaluated for VOC removal. Also, single perovskites including LaCoO3 and LaMnO3 are tested for the comparison purpose. Toluene (C7H8) is one of the important VOCs which are commonly applied in chemical processes. In addition to its wide application, C7H8 has high toxicity at a low concentration. Therefore, C7H8 is selected as the target compound in this study. Experimental results indicate that double perovskite (La2CoMnO6) has better activity if compared with single perovskites. Especially, C7H8 can be completely oxidized to CO2 at 300oC as La2CoMnO6 is applied. Characterization of catalysts indicates that double perovskite has unique surface properties and is of higher amounts of lattice oxygen, leading to higher activity. For durability test, La2CoMnO6 maintains high C7H8 removal efficiency of 100% at 300oC and 30,000 h-1, and it also shows good resistance to CO2 (5%) and H2O(g) (5%) of gas streams tested. For various VOCs including isopropyl alcohol (C3H8O), ethanal (C2H4O), and ethylene (C2H4) tested, as high as 100% efficiency could be achieved with double perovskite-type catalyst operated at 300℃, indicating that double perovskites are promising catalysts for VOCs removal, and possible mechanisms will be elucidated in this paper.

Keywords: volatile organic compounds, Toluene (C7H8), double perovskite-type catalyst, catalysis

Procedia PDF Downloads 148

Authors: Anna Lower, Michal Lower, Robert Masztalski, Agnieszka Szumilas

Abstract:

Contemporary cities are facing serious congestion and parking problems. In urban transport policy the introduction of the park and ride system (P&R) is an increasingly popular way of limiting vehicular traffic. The determining of P&R facilities location is a key aspect of the system. Criteria for assessing the quality of the selected location are formulated generally and descriptively. The research outsourced to specialists are expensive and time consuming. The most focus is on the examination of a few selected places. The practice has shown that the choice of the location of these sites in a intuitive way without a detailed analysis of all the circumstances, often gives negative results. Then the existing facilities are not used as expected. Methods of location as a research topic are also widely taken in the scientific literature. Built mathematical models often do not bring the problem comprehensively, e.g. assuming that the city is linear, developed along one important communications corridor. The paper presents a new method where the expert knowledge is applied to fuzzy inference model. With such a built system even a less experienced person could benefit from it, e.g. urban planners, officials. The analysis result is obtained in a very short time, so a large number of the proposed location can also be verified in a short time. The proposed method is intended for testing of car parks location in a city. The paper will show selected examples of locations of the P&R facilities in cities planning to introduce the P&R. The analysis of existing objects will also be shown in the paper and they will be confronted with the opinions of the system users, with particular emphasis on unpopular locations. The research are executed using the fuzzy inference model which was built and described in more detail in the earlier paper of the authors. The results of analyzes are compared to documents of P&R facilities location outsourced by the city and opinions of existing facilities users expressed on social networking sites. The research of existing facilities were conducted by means of the fuzzy model. The results are consistent with actual users feedback. The proposed method proves to be good, but does not require the involvement of a large experts team and large financial contributions for complicated research. The method also provides an opportunity to show the alternative location of P&R facilities. The performed studies show that the method has been confirmed. The method can be applied in urban planning of the P&R facilities location in relation to the accompanying functions. Although the results of the method are approximate, they are not worse than results of analysis of employed experts. The advantage of this method is ease of use, which simplifies the professional expert analysis. The ability of analyzing a large number of alternative locations gives a broader view on the problem. It is valuable that the arduous analysis of the team of people can be replaced by the model's calculation. According to the authors, the proposed method is also suitable for implementation on a GIS platform.

Keywords: fuzzy logic inference, park and ride system, P&R facilities, P&R location

Procedia PDF Downloads 312

Authors: Yuanyuan Fu

Abstract:

Background and Purpose: Along with the change of society and economy, the traditional home function of old people has gradually weakened in the contemporary China. Acknowledging these situations, to better meet old people’s needs on formal services and improve the quality of later life, this study seeks to identify patterns of intended service use among frail old people living in the communities and examined determinants that explain heterogeneous variations in old people’s intended service use patterns. Additionally, this study also tested the relationship between culture value and intended service use patterns and the mediating role of enabling factors in terms of culture value and intended service use patterns. Methods：Participants were recruited from Haidian District, Beijing, China in 2015. The multi-stage sampling method was adopted to select sub-districts, communities and old people aged 70 years old or older. After screening, 577 old people with limitations in daily life, were successfully interviewed. After data cleaning, 550 samples were included for data analysis. This study establishes a conceptual framework based on the Anderson Model (including predisposing factors, enabling factors and need factors), and further developed it by adding culture value factors (including attitudes towards filial piety and attitudes towards social face). Using a latent class analysis (LCA), this study classifies overall patterns of old people’s formal service utilization. Fourteen types of formal services were taken into account, including housework, voluntary support, transportation, home-delivered meals, and home-delivery medical care, elderly’s canteen and day-care center/respite care and so on. Structural equation modeling (SEM) was used to examine the direct effect of culture value on service use pattern, and the mediating effect of the enabling factors. Results: The LCA classified a hierarchical structure of service use patterns: multiple intended service use (N=69, 23%), selective intended service use (N=129, 23%), and light intended service use (N=352, 64%). Through SEM, after controlling predisposing factors and need factors, the results showed the significant direct effect of culture value on older people’s intended service use patterns. Enabling factors had a partial mediation effect on the relationship between culture value and the patterns. Conclusions and Implications: Differentiation of formal services may be important for meeting frail old people’s service needs and distributing program resources by identifying target populations for intervention, which may make reference to specific interventions to better support frail old people. Additionally, culture value had a unique direct effect on the intended service use patterns of frail old people in China, enriching our theoretical understanding of sources of culture value and their impacts. The findings also highlighted the mediation effects of enabling factors on the relationship between culture value factors and intended service use patterns. This study suggests that researchers and service providers should pay more attention to the important role of culture value factors in contributing to intended service use patterns and also be more sensitive to the mediating effect of enabling factors when discussing the relationship between culture value and the patterns.

Keywords: frail old people, intended service use pattern, culture value, enabling factors, contemporary China, latent class analysis

Procedia PDF Downloads 211

Authors: Z. S. Haidar

Abstract:

Millions of teeth are removed annually, and dental extraction is one of the most commonly performed surgical procedures globally. Whether due to caries, periodontal disease, or trauma, exodontia and the ensuing wound healing and bone remodeling processes of the resultant socket (hole in the jaw bone) usually result in serious deformities of the residual alveolar osseous ridge and surrounding soft tissues (reduced height/width). Such voluminous changes render the placement of a proper conventional bridge, denture, or even an implant-supported prosthesis extremely challenging. Further, most extractions continue to be performed with no regard for preventing the onset of alveolar osteitis (also known as dry socket, a painful and difficult-to-treat/-manage condition post-exodontia). Hence, such serious resorptive morphological changes often result in significant facial deformities and a negative impact on the overall Quality of Life (QoL) of patients (and oral health-related QoL); alarming, particularly for the geriatric with compromised healing and in light of the thriving longevity statistics. Despite advances in tissue/wound grafting, serious limitations continue to exist, including efficacy and clinical outcome predictability, cost, treatment time, expertise, and risk of immune reactions. For cases of dry socket, specifically, the commercially available and often-prescribed home remedies are highly-lacking. Indeed, most are not recommended for use anymore. Alveogyl is a fine example. Hence, there is a great market demand and need for alternative solutions. Herein, SockGEL/PLUG (patent pending), an innovative, all-natural, drug-free, and injectable thermo-responsive hydrogel, was designed, formulated, characterized, and evaluated as an osteogenic, angiogenic, anti-microbial, and pain-soothing suture-free intra-alveolar dressing, safe and efficacious for use in fresh extraction sockets, immediately post-exodontia. It is composed of FDA-approved, biocompatible and biodegradable polymers, self-assembled electro-statically to formulate a scaffolding matrix to (1) prevent the on-set of alveolar osteitis via securing the fibrin-clot in situ and protecting/sealing the socket from contamination/infection; and (2) endogenously promote/accelerate wound healing and bone remodeling to preserve the volume of the alveolus. The intrinsic properties of the SockGEL/PLUG hydrogel were evaluated physical-chemical-mechanically for safety (cell viability), viscosity, rheology, bio-distribution, and essentially, capacity to induce wound healing and osteogenesis (small defect, in vivo) without any signaling cues from exogenous cells, growth factors or drugs. The proposed animal model of cranial critical-sized and non-vascularized bone defects shall provide new and critical insights into the role and mechanism of the employed natural bio-polymer blend and gel product in endogenous reparative regeneration of soft tissues and bone morphogenesis. Alongside, the fine-tuning of our modified formulation method will further tackle appropriateness, reproducibility, scalability, ease, and speed in producing stable, biodegradable, and sterilizable thermo-sensitive matrices (3-dimensional interpenetrating yet porous polymeric network) suitable for the intra-socket application. Findings are anticipated to provide sufficient evidence to translate into pilot clinical trials and validate the innovation before engaging the market for feasibility, acceptance, and cost-effectiveness studies.

Keywords: hydrogel, nanotechnology, bioengineering, bone regeneration, nanogel, drug delivery

Procedia PDF Downloads 96

Authors: Sonia Boscenco, Zihan Wang, Euclides José de Mendoça Filho, João Paulo Hoppe, Irina Pokhvisneva, Geoffrey B.C. Hall, Michael J. Meaney, Patricia Pelufo Silveira

Abstract:

Entropy can be described as a measure of the number of states of a system, and when used in the context of physiological time-based signals, it serves as a measure of complexity. In functional connectivity data, entropy can account for the moment-to-moment variability that is neglected in traditional functional magnetic resonance imaging (fMRI) analyses. While brain fMRI resting state entropy has been associated with some pathological conditions like schizophrenia, no investigations have explored the association between brain entropy measures and individual differences in child behavior in healthy children. We describe a novel exploratory approach to evaluate brain fMRI resting state data in two child cohorts, and MAVAN (N=54, 4.5 years, 48% males) and GUSTO (N = 206, 4.5 years, 48% males) and its associations to child behavior, that can be used in future research in the context of child exposures and long-term health. Following rs-fMRI data pre-processing and Shannon entropy calculation across 32 network regions of interest to acquire 496 unique functional connections, partial correlation coefficient analysis adjusted for sex was performed to identify associations between entropy data and Strengths and Difficulties questionnaire in MAVAN and Child Behavior Checklist domains in GUSTO. Significance was set at p < 0.01, and we found eight significant associations in GUSTO. Negative associations were found between two frontoparietal regions and cerebellar posterior and oppositional defiant problems, (r = -0.212, p = 0.006) and (r = -0.200, p = 0.009). Positive associations were identified between somatic complaints and four default mode connections: salience insula (r = 0.202, p < 0.01), dorsal attention intraparietal sulcus (r = 0.231, p = 0.003), language inferior frontal gyrus (r = 0.207, p = 0.008) and language posterior superior temporal gyrus (r = 0.210, p = 0.008). Positive associations were also found between insula and frontoparietal connection and attention deficit / hyperactivity problems (r = 0.200, p < 0.01), and insula – default mode connection and pervasive developmental problems (r = 0.210, p = 0.007). In MAVAN, ten significant associations were identified. Two positive associations were found = with prosocial scores: the salience prefrontal cortex and dorsal attention connection (r = 0.474, p = 0.005) and the salience supramarginal gyrus and dorsal attention intraparietal sulcus (r = 0.447, p = 0.008). The insula and prefrontal connection were negatively associated with peer problems (r = -0.437, p < 0.01). Conduct problems were negatively associated with six separate connections, the left salience insula and right salience insula (r = -0.449, p = 0.008), left salience insula and right salience supramarginal gyrus (r = -0.512, p = 0.002), the default mode and visual network (r = -0.444, p = 0.009), dorsal attention and language network (r = -0.490, p = 0.003), and default mode and posterior parietal cortex (r = -0.546, p = 0.001). Entropy measures of resting state functional connectivity can be used to identify individual differences in brain function that are correlated with variation in behavioral problems in healthy children. Further studies applying this marker into the context of environmental exposures are warranted.

Keywords: child behaviour, functional connectivity, imaging, Shannon entropy

Procedia PDF Downloads 184

Authors: Lesibana Rafapa

Abstract:

Accounts exist of circumcision-anchored cultural initiation in central Africa, East Africa, Southern Africa, North Africa, and West Africa -straddling states like Botswana, Kenya, Lesotho, Malawi, Senegal, South Africa, Zambia, and Zimbabwe. This attests to the continent-wide spread of this cultural practice. In this paper, the writer relates the cultural aspect of circumcision-subsuming initiation among black African cultural groups across the continent to the notion that African cultures are varied yet subscribe to a common central concept. The premise of the paper is that the common practice of initiation for both male and female children that have to be initiated by adults to the tradition and customs of a people coincides with such a central concept. The practice of traditional initiation is as broad as to encompass aspects of spirituality, morality, and social organisation, in the nature of the central concept of which it is a trans-sectional part. Cultural initiation, sometimes referred to as traditional circumcision, constitutes culture-determined rites of passage for the initiates. The study’s aim, the findings of which are presented in this paper, was to probe gender equality in the development and promotion of the cultural practice of initiation. The researcher intended to demonstrate how in South Africa, female circumcision is treated equally or marginalised in efforts of the democratic government to regulate and strengthen the practice of circumcision as part of its broader liberation programme meant to reverse politico-cultural bondage experienced during apartheid rule that the present black regime helped bring to an end. It is argued that the failure to regard female circumcision as equal to its male counterpart is a travesty of the black government’s legislation and policies espousing equality and the protection and empowerment of vulnerable and previously marginalised population groups that include black women. The writer did a desk-top study of the history and characteristics of female circumcision among the black Northern Sotho, VaTsonga, and VhaVenda cultural groups of the Limpopo Province, stretching north to the border of South Africa with Zimbabwe, as well as literature on how political and other authorities exert efforts to preserve and empower the practice. The findings were that male initiation is foregrounded and totalised to represent the practice of initiation as a whole, at the expense of its female counterpart facing marginalisation and unequal regard. It is outlined in this paper how such impoverishment of an otherwise woman-empowering cultural practice deprives hitherto black cultures that suffered brutal repression during apartheid of a fuller recovery much needed in the democratic era. The writer applies some aspects of postcolonial theory and some tropes of feminism in the discussion of an uneven status of cultural circumcision at the hands of present day powers that be.

Keywords: African cultures, female circumcision, gender equality, women empowerment

Procedia PDF Downloads 139