Search results for: repair-cost limit

Authors: Acacia A. Salomão, Willian L. Gomes da Silva, Gustavo G. Shimamoto, Matthieu Tubino

Abstract:

Biodiesel physical and chemical properties depend on the raw material composition used in its synthesis. Saturated fatty acid esters confer high oxidative stability, while unsaturated fatty acid esters improve the cold flow properties. In this study, an alternative vegetal source - the macauba kernel oil - was used in the biodiesel synthesis instead of conventional sources. Macauba can be collected from native palm trees and is found in several regions in Brazil. Its oil is a promising source when compared to several other oils commonly obtained from food products, such as soybean, corn or canola oil, due to its specific characteristics. However, the usage of biodiesel made from macauba oil alone is not recommended due to the difficulty of producing macauba in large quantities. For this reason, this project proposes the usage of blends of the macauba oil with conventional oils. These blends were prepared by mixing the macauba biodiesel with biodiesels obtained from soybean, corn, and from residual frying oil, in the following proportions: 20:80, 50:50 e 80:20 (w/w). Three parameters were evaluated, using the standard methods, in order to check the quality of the produced biofuel and its blends: oxidative stability, cold filter plugging point (CFPP), and iodine value. The induction period (IP) expresses the oxidative stability of the biodiesel, the CFPP expresses the lowest temperature in which the biodiesel flows through a filter without plugging the system and the iodine value is a measure of the number of double bonds in a sample. The biodiesels obtained from soybean, residual frying oil and corn presented iodine values higher than 110 g/100 g, low oxidative stability and low CFPP. The IP values obtained from these biodiesels were lower than 8 h, which is below the recommended standard value. On the other hand, the CFPP value was found within the allowed limit (5 ºC is the maximum). Regarding the macauba biodiesel, a low iodine value was observed (31.6 g/100 g), which indicates the presence of high content of saturated fatty acid esters. The presence of saturated fatty acid esters should imply in a high oxidative stability (which was found accordingly, with IP = 64 h), and high CFPP, but curiously the latter was not observed (-3 ºC). This behavior can be explained by looking at the size of the carbon chains, as 65% of this biodiesel is composed by short chain saturated fatty acid esters (less than 14 carbons). The high oxidative stability and the low CFPP of macauba biodiesel are what make this biofuel a promising source. The soybean, corn and residual frying oil biodiesels also have low CFPP, but low oxidative stability. Therefore the blends proposed in this work, if compared to the common biodiesels, maintain the flow properties but present enhanced oxidative stability.

Keywords: biodiesel, blends, macauba kernel oil, stability oxidative

Procedia PDF Downloads 538

Authors: Jos Olijve

Abstract:

Introduction and Purpose: Endotoxins are found in the outer membrane of gram-negative bacteria and have profound in vitro and in vivo responses. They can trigger strong immune responses and negatively affect various cellar activities particular cells expressing toll-like receptors. They are therefore unwanted contaminants of biomaterials sourced from natural raw materials, and their activity must be as low as possible. Collagen and gelatin are natural extracellular matrix components and have, due to their low allergenic potential, suitable biological properties, and tunable physical characteristics, high potential in biomedical applications. The purpose of this study was to determine the influence of autoclave sterilization of gelatin on physical properties and endotoxin level compared to surfactant purified gelatin. Methods: Type A gelatin from Sigma-Aldrich (G1890) with endotoxin level of 35000 endotoxin units (EU) per gram gelatin and type A gelatins from Rousselot Gent with endotoxin activity of 30000 EU per gram were used. A 10 w/w% G1890 gelatin solution was autoclave sterilized during 30 minutes at 121°C and 1 bar over pressure. The physical properties and the endotoxin level of the sterilized G1890 gelatin were compared to a type A gelatin from Rousselot purified with Triton X100 surfactant. The Triton X100 was added to a concentration of 0.5 w/w% which is above the critical micellar concentration. The gelatin surfactant mixtures were kept for 30-45 minutes under constant stirring at 55-60°C. The Triton X100 was removed by active carbon filtration. The endotoxin levels of the gelatins were measured using the Endozyme recombinant factor C method from Hyglos GmbH (Germany). Results and Discussion: Autoclave sterilization significantly affect the physical properties of gelatin. Molecular weight of G1890 decreased from 140 to 50kDa, and gel strength decreased from 300 to 40g. The endotoxin level of the gelatin reduced after sterilization from 35000 EU/g to levels of 400-500 EU/g. These endotoxin levels are however still far above the upper endotoxin level of 0.05 EU/ml, which resembles 5 EU/g gelatin based on a 1% gelatin solution, to avoid cell proliferation alteration. Molecular weight and gel strength of Rousselot gelatin was not altered after Triton X100 purification and remained 150kDa and 300g respectively. The endotoxin levels of Triton X100 purified Rousselot gelatin was < 5EU/g gelatin. Conclusion: Autoclave sterilization of gelatin is, in comparison to Triton X100 purification, not efficient to inactivate endotoxin levels in gelatin to levels below the upper limit to avoid cell proliferation alteration. Autoclave sterilization gave a significant decrease in molecular weight and gel strength which makes autoclave sterilized gelatin, in comparison to Triton X100 purified gelatin, not suitable for 3D printing.

Keywords: endotoxin, gelatin, molecular weight, sterilization, Triton X100

Procedia PDF Downloads 231

Authors: Hemant Upadhyay, Tarun Kumar Kundu

Abstract:

It is utmost important for a blast furnace operator to understand the mechanisms governing the liquid flow, accumulation, drainage and heat transfer between various phases in blast furnace hearth for a stable and efficient blast furnace operation. Abnormal drainage behavior may lead to high liquid build up in the hearth. Operational problems such as pressurization, low wind intake, and lower material descent rates, normally be encountered if the liquid levels in the hearth exceed a critical limit when Hearth coke and Deadman start to float. Similarly, hot metal temperature is an important parameter to be controlled in the BF operation; it should be kept at an optimal level to obtain desired product quality and a stable BF performance. It is not possible to carry out any direct measurement of above due to the hostile conditions in the hearth with chemically aggressive hot liquids. The objective here is to develop a mathematical model to simulate the variation in hot metal / slag accumulation and temperature during the tapping of the blast furnace based on the computed drainage rate, production rate, mass balance, heat transfer between metal and slag, metal and solids, slag and solids as well as among the various zones of metal and slag itself. For modeling purpose, the BF hearth is considered as a pressurized vessel, filled with solid coke particles. Liquids trickle down in hearth from top and accumulate in voids between the coke particles which are assumed thermally saturated. A set of generic mass balance equations gives the amount of metal and slag intake in hearth. A small drainage (tap hole) is situated at the bottom of the hearth and flow rate of liquids from tap hole is computed taking in account the amount of both the phases accumulated their level in hearth, pressure from gases in the furnace and erosion behaviors of tap hole itself. Heat transfer equations provide the exchange of heat between various layers of liquid metal and slag, and heat loss to cooling system through refractories. Based on all that information a dynamic simulation is carried out which provides real time information of liquids accumulation in hearth before and during tapping, drainage rate and its variation, predicts critical event timings during tapping and expected tapping temperature of metal and slag on preset time intervals. The model is in use at JSPL, India BF-II and its output is regularly cross-checked with actual tapping data, which are in good agreement.

Keywords: blast furnace, hearth, deadman, hotmetal

Procedia PDF Downloads 183

Authors: Amir Gharavi, Mohamed Hassan, Amjad Shah

Abstract:

The main characteristics of unconventional reservoirs include low-to ultra low permeability and low-to-moderate porosity. As a result, hydrocarbon production from these reservoirs requires different extraction technologies than from conventional resources. An unconventional reservoir must be stimulated to produce hydrocarbons at an acceptable flow rate to recover commercial quantities of hydrocarbons. Permeability for unconventional reservoirs is mostly below 0.1 mD, and reservoirs with permeability above 0.1 mD are generally considered to be conventional. The hydrocarbon held in these formations naturally will not move towards producing wells at economic rates without aid from hydraulic fracturing which is the only technique to assess these tight reservoir productions. Horizontal well with multi-stage fracking is the key technique to maximize stimulated reservoir volume and achieve commercial production. The main objective of this research paper is to investigate development options for a tight mature oilfield. This includes multistage hydraulic fracturing and spacing by building of reservoir models in the Reveal simulator to model potential development options based on sidetracking the existing vertical well. To simulate potential options, reservoir models have been built in the Reveal. An existing Petrel geological model was used to build the static parts of these models. A FBHP limit of 40bars was assumed to take into account pump operating limits and to maintain the reservoir pressure above the bubble point. 300m, 600m and 900m lateral length wells were modelled, in conjunction with 4, 6 and 8 stages of fracs. Simulation results indicate that higher initial recoveries and peak oil rates are obtained with longer well lengths and also with more fracs and spacing. For a 25year forecast, the ultimate recovery ranging from 0.4% to 2.56% for 300m and 1000m laterals respectively. The 900m lateral with 8 fracs 100m spacing gave the highest peak rate of 120m3/day, with the 600m and 300m cases giving initial peak rates of 110m3/day. Similarly, recovery factor for the 900m lateral with 8 fracs and 100m spacing was the highest at 2.65% after 25 years. The corresponding values for the 300m and 600m laterals were 2.37% and 2.42%. Therefore, the study suggests that longer laterals with 8 fracs and 100m spacing provided the optimal recovery, and this design is recommended as the basis for further study.

Keywords: unconventional, resource, hydraulic, fracturing

Procedia PDF Downloads 297

Authors: Ellen Patricia, Marilou Hyson

Abstract:

Coaching has been showing great potential to strengthen the impact of brief group trainings and help early childhood teachers solve specific problems at work with the goal of raising the quality of early childhood services. However, there have been some doubts about the benefits that village teachers can receive from coaching. It is perceived that village teachers may struggle with the thinking skills needed to make coaching beneficial. Furthermore, there are reservations about whether principals and supervisors in villages are open to coaching’s facilitative approach, as opposed to the directive approach they have been using. As such, the use of coaching to develop the professionalism of early childhood teachers in the villages needs to be examined. The Coaching Pilot for early childhood teachers in Indonesia villages provides insights for the above issues. The Coaching Pilot is part of the ECED Frontline Pilot, which is a collaboration project between the Government of Indonesia and the World Bank with the support from the Australian Government (DFAT). The Pilot started with coordinated efforts with the local government in two districts to select principals and supervisors who have been equipped with basic knowledge about early childhood education to take part in 2-days coaching training. Afterwards, the participants were asked to collect 25 hours of coaching early childhood teachers who have participated in the Enhanced Basic Training for village teachers. The participants who completed this requirement were then invited to come for an assessment of their coaching skills. Following that, a qualitative evaluation was conducted using in-depth interviews and Focus Group Discussion techniques. The evaluation focuses on the impact of the coaching pilot in helping the village teachers to develop in their professionalism, as well as on the sustainability of the intervention. Results from the evaluation indicated that although their low education may limit their thinking skills, village teachers benefited from the coaching that they received. Moreover, the evaluation results also suggested that with enough training and support, principals and supervisors in the villages were able to provide an adequate coaching service for the teachers. On top of that, beyond this small start, interest is growing, both within the pilot districts and even beyond, due to word of mouth of the benefits that the Coaching Pilot has created. The districts where coaching was piloted have planned to continue the coaching program, since a number of early childhood teachers have requested to be coached, and a number of principals and supervisors have also requested to be trained as a coach. Furthermore, the Association for Early Childhood Educators in Indonesia has started to adopt coaching into their program. Although further research is needed, the Coaching Pilot suggests that coaching can positively impact early childhood teachers in villages, and village principals and supervisors can become a promising source of future coaches. As such, coaching has a significant potential to become a sustainable model for a continuous professional development program for early childhood teachers in villages.

Keywords: coaching, coaching pilot, early childhood teachers, principals and supervisors, village teachers

Procedia PDF Downloads 237

Authors: Daniel Manaye Kabtamu, Anteneh Wodaje Bayeh

Abstract:

With the development and utilization of new energy technology, people’s demand for large-scale energy storage system has become increasingly urgent. Vanadium redox flow battery (VRFB) is one of the most promising technologies for grid-scale energy storage applications because of numerous attractive features, such as long cycle life, high safety, and flexible design. However, the relatively low energy efficiency and high production cost of the VRFB still limit its practical implementations. It is of great attention to enhance its energy efficiency and reduce its cost. One of the main components of VRFB that can impressively impact the efficiency and final cost is the electrode materials, which provide the reactions sites for redox couples (V₂₊/V³⁺ and VO²⁺/VO₂⁺). Graphite felt (GF) is a typical carbon-based material commonly employed as electrode for VRFB due to low-cost, good chemical and mechanical stability. However, pristine GF exhibits insufficient wettability, low specific surface area, and poor kinetics reversibility, leading to low energy efficiency of the battery. Therefore, it is crucial to further modify the GF electrode to improve its electrochemical performance towards VRFB by employing active electrocatalysts, such as less expensive metal oxides. This study successfully fabricates low-cost plate-like bismuth vanadate (BiVO₄) material through a simple one-step hydrothermal route, employed as an electrocatalyst to adorn the GF for use as the negative electrode in VRFB. The experimental results show that BiVO₄-3h exhibits the optimal electrocatalytic activity and reversibility for the vanadium redox couples among all samples. The energy efficiency of the VRFB cell assembled with BiVO₄-decorated GF as the negative electrode is found to be 75.42% at 100 mA cm−2, which is about 10.24% more efficient than that of the cell assembled with heat-treated graphite felt (HT-GF) electrode. The possible reasons for the activity enhancement can be ascribed to the existence of oxygen vacancies in the BiVO₄ lattice structure and the relatively high surface area of BiVO₄, which provide more active sites for facilitating the vanadium redox reactions. Furthermore, the BiVO₄-GF electrode obstructs the competitive irreversible hydrogen evolution reaction on the negative side of the cell, and it also has better wettability. Impressively, BiVO₄-GF as the negative electrode shows good stability over 100 cycles. Thus, BiVO₄-GF is a promising negative electrode candidate for practical VRFB applications.

Keywords: BiVO₄ electrocatalyst, electrochemical energy storage, graphite felt, vanadium redox flow battery

Procedia PDF Downloads 1571

Authors: Abdullah Mohammadi

Abstract:

Years of prolong war in Afghanistan has led to one of the largest refugee and migrant populations in the contemporary world. During this continuous unrest which began in 1970s (by military coup, Marxist revolution and the subsequent invasion of USSR), over one-third of the population migrated to neighboring countries, especially Pakistan and Iran. After the Soviet Army withdrawal in 1989, a new wave of conflicts emerged between rival Afghan groups and this led to new refugees. Taliban period, also, created its own refugees. During all these years, I.R. of Iran has been one of the main destinations of Afghan refugees and migrants. At first, due to the political situation after Islamic Revolution, Iran government didn’t restrict the entry of Afghan refugees. Those who came first in Iran received ID cards and had access to education and healthcare services. But in 1990s, due to economic and social concerns, Iran’s policy towards Afghan refugees and migrants changed. The government has tried to identify and register Afghans in Iran and limit their access to some services and jobs. Unfortunately, there are few studies on Afghan refugees and migrants’ situation in Iran and we have a dim and vague picture of them. Of the few studies done on this group, none of them focus on the illegal Afghan migrants’ situation in Iran. Here, we tried to study the social and economic aspects of illegal Afghan migrants’ living in Iran. In doing so, we interviewed 24 illegal Afghan migrants in Iran. The method applied for analyzing the data is thematic analysis. For the interviews, we chose family heads (17 men and 7 women). According to the findings, illegal Afghan migrants’ socio-economic situation in Iran is very undesirable. Its main cause is the marginalization of this group which is resulted from government policies towards Afghan migrants. Most of the illegal Afghan migrants work in unskilled and inferior jobs and live in rent houses on the margins of cities and villages. None of them could buy a house or vehicle due to law. Based on their income, they form one of the lowest, unprivileged groups in the society. Socially, they face many problems in their everyday life: social insecurity, harassment and violence, misuse of their situation by police and people, lack of education opportunity, etc. In general, we may conclude that illegal Afghan migrant have little adaptation with Iran’s society. They face severe limitations compared to legal migrants and refugees and have no opportunity for upward social mobility. However, they have managed some strategies to face these difficulties including: seeking financial and emotional helps from family and friendship networks, sending one of the family members to third country (mostly to European countries), establishing self-administered schools for children (schools which are illegal and run by Afghan educated youth).

Keywords: illegal Afghan migrants, marginalization, social insecurity, upward social mobility

Procedia PDF Downloads 317

Authors: Muhammad Yasir Tarar

Abstract:

Background: Intraarticular steroid injections are an effective option in alleviating the symptoms of conditions like osteoarthritis, rheumatoid arthritis, crystal arthropathy, and rotator cuff tendinopathy. Most of these injections are conducted in the elderly who are on polypharmacy, including anticoagulants at times. Up to 6% of patients aged 80-84 years have been reported to be taking Warfarin. The literature availability on safety quotient for patients undergoing intraarticular injections on Warfarin is scarce. It has remained debatable over the years which approach is safe for these patients. Continuing warfarin has a theoretical bleeding risk, and stopping it can lead to even severe life-threatening thromboembolic events in high-risk patients. Objectives: To evaluate the risk of bleeding complications in patients on warfarin undergoing intraarticular injections or arthrocentesis. Study Design & Methods: A literature search of MEDLINE (1946 to present), EMBASE (1974 to present), and Cochrane CENTRAL (1988 to present) databases were conducted using any combination of the keywords, Injection, Knee, Shoulder, Joint, Intraarticular, arthrocentesis, Warfarin, and Anticoagulation in November 2020 for articles published in any language with no publication year limit. The study inclusion criteria included reporting on the rate of bleeding complications following injection of the knee or shoulder in patients on warfarin treatment. Randomized control trials and prospective and retrospective study designs were included. An electronic standardized Performa for data extraction was made. The Preferred Reporting Items for Systematic Review and Meta-Analyses (PRISMA) the methodology was used. The articles were appraised using the methodological index for nonrandomized studies. The Cochrane Risk of Bias Tool used to assess the risk of bias in included RCTs and the MINORS tool for assessment of bias in observational studies. Results: The search of databases resulted in a total of 852 articles. Relevant articles as per the inclusion criteria were shortlisted, 7 articles deemed suitable to be include. A total of 1033 joints sample size was undertaken with specified knee and shoulder joints of a total of 820. Only 6 joints had bleeding complications, 5 early bleeding at the time of injection or aspiration, and one late bleeding complication with INR of 5, additionally, 2 patients complained of bruising, 3 of pain, and 1 managed for infection. Conclusions: The results of the metanalysis show that it is relatively safe to perform intraarticular injections in patients on Warfarin regardless of the INR range.

Keywords: arthrocentesis, warfarin, bleeding, injection

Procedia PDF Downloads 76

Authors: Bamikole J. Adeyemi, Prashant Jadhawar, Lateef Akanji

Abstract:

Theoretically, there exist two mathematical interfaces (fluid-solid and fluid-fluid) when a liquid film is present on solid surfaces. These interfaces overlap if the mineral surface is oil-wet or mixed wet, and therefore, the effects of disjoining pressure are significant on both boundaries. Hence, dewetting is a necessary process that could detach oil from the mineral surface. However, if the thickness of the thin water film directly in contact with the surface is large enough, disjoining pressure can be thought to be zero at the liquid-liquid interface. Recent studies show that the integration of fluid-fluid interactions with fluid-rock interactions is an important step towards a holistic approach to understanding smart water effects. Experiments have shown that the brine solution can alter the micro forces at oil-water interfaces, and these ion-specific interactions lead to oil emulsion formation. The natural emulsifiers present in crude oil behave as polyelectrolytes when the oil interfaces with low salinity water. Wettability alteration caused by low salinity waterflooding during Enhanced Oil Recovery (EOR) process results from the activities of divalent ions. However, polyelectrolytes are said to lose their viscoelastic property with increasing cation concentrations. In this work, the influence of cation concentrations on the dynamics of viscoelastic liquid-liquid interfaces is numerically investigated. The resultant ion concentrations at the crude oil/brine interfaces were estimated using a surface complexation model. Subsequently, the ion concentration parameter is integrated into a mathematical model to describe its effects on the dynamics of a viscoelastic interfacial thin film. The film growth, stability, and rupture were measured after different time steps for three types of fluids (Newtonian, purely elastic and viscoelastic fluids). The interfacial films respond to exposure time in a similar manner with an increasing growth rate, which resulted in the formation of more droplets with time. Increased surfactant accumulation at the interface results in a higher film growth rate which leads to instability and subsequent formation of more satellite droplets. Purely elastic and viscoelastic properties limit film growth rate and consequent film stability compared to the Newtonian fluid. Therefore, low salinity and reduced concentration of the potential determining ions in injection water will lead to improved interfacial viscoelasticity.

Keywords: liquid-liquid interfaces, surfactant concentrations, potential determining ions, residual oil mobilization

Procedia PDF Downloads 141

Authors: Mala Tankam Carine, Kekeunou Sévilor, Nukenine Elias

Abstract:

Storage and preservation of agricultural products remain the only conditions ensuring the almost permanent availability of foodstuffs. However, infestations due to insects and microorganisms often occur. Callosobruchus maculatus is a pest that causes a lot of damage to cowpea stocks in the tropics. Several methods are adopted to limit their damage, but the use of synthetic chemical insecticides is the most widespread. Biopesticides in sustainable agriculture respond to several environmental, economic and social concerns while offering innovative opportunities that are ecologically and economically viable for producers, workers, consumers and ecosystems. Our main objective is to evaluate the insecticidal efficacy of binary combinations of Fossilshield with root-bark powder of Securidaca longepedunculata against Callosobruchus maculatus in stored cowpea Vigna unguiculata. Laboratory bioassays were conducted in stored grains to evaluate the toxicity of root-bark powder of Securidaca longepedunculata alone or combined with diatomaceous earth Fossil-Shield ® against C. maculatus. Twenty-hour-old adults of C. maculatus were exposed to 50g of cowpea seeds treated with four doses (10, 20, 30, and 40g/kg) of root-bark powder of S. longepedunculata, on the one hand, and (0.5, 1, 1.5, and 2 g/kg) on DE and binary combinations on the other hand. 0g/kg corresponded to untreated control. Adult mortality was recorded up to 7 days (d) post-treatment, whereas the number of F1 progeny was assessed after 30 d. Weight loss and germinative ability were conducted after 120 d. All treatments were arranged according to a completely randomized block with four replicates. The combined mixture of S. longepedunculata and DE controlled the beetle faster compared to the root-bark powder of S. longepedunculata alone. According to the Co-toxicity coefficient, additive effect of binary combinations was recorded at 3-day post-exposure time with the mixture 25% FossilShield + 75% S. longepedunculata. A synergistic action was observed after 3-d post-exposure at mixture 50% FossilShield + 50% S. longepedunculata and at 1-d and 3-d post-exposure periods at mixture 75% FossilShield + 25% S. longepedunculata. The mixture 25% FossilShield + 75% S. longepedunculata induced a decreased progeny of 6 times fewer individuals for 4.5 times less weight loss and 2, 9 times more sprouted grains than with root-bark powder of S. longepedunculata. The combination of FossilShield + S. longepedunculata was more potent than root-bark powder of S. longepedunculata alone, although the root-bark powder of S. longepedunculata caused significant reduction of F1 adults compared to the control. Combined action of botanical insecticides with FossilShield as a grain protectant in an integrated pest management approach is discussed.

Keywords: diatomaceous earth, cowpea, callosobruchus maculatus, securidaca longepedunculata, combined action, co-toxicity coefficient

Procedia PDF Downloads 69

Authors: Guerich Mohamed, Assaf Samir

Abstract:

The application of viscoelastic materials in the form of constrained layers in mechanical structures is an efficient and cost-effective technique for solving noise and vibration problems. This technique requires a design tool to select the best location, type, and thickness of the damping treatment. This paper presents a finite element model for the vibration of beams partially or fully covered with a constrained viscoelastic damping material. The model is based on Bernoulli-Euler theory for the faces and Timoshenko beam theory for the core. It uses four variables: the through-thickness constant deflection, the axial displacements of the faces, and the bending rotation of the beam. The sandwich beam finite element is compatible with the conventional C1 finite element for homogenous beams. To validate the proposed model, several free vibration analyses of fully or partially covered beams, with different locations of the damping patches and different percent coverage, are studied. The results show that the proposed approach can be used as an effective tool to study the influence of the location and treatment size on the natural frequencies and the associated modal loss factors. Then, a parametric study regarding the variation in the damping characteristics of partially covered beams has been conducted. In these studies, the effect of core shear modulus value, the effect of patch size variation, the thickness of constraining layer, and the core and the locations of the patches are considered. In partial coverage, the spatial distribution of additive damping by using viscoelastic material is as important as the thickness and material properties of the viscoelastic layer and the constraining layer. Indeed, to limit added mass and to attain maximum damping, the damping patches should be placed at optimum locations. These locations are often selected using the modal strain energy indicator. Following this approach, the damping patches are applied over regions of the base structure with the highest modal strain energy to target specific modes of vibration. In the present study, a more efficient indicator is proposed, which consists of placing the damping patches over regions of high energy dissipation through the viscoelastic layer of the fully covered sandwich beam. The presented approach is used in an optimization method to select the best location for the damping patches as well as the material thicknesses and material properties of the layers that will yield optimal damping with the minimum area of coverage.

Keywords: finite element model, damping treatment, viscoelastic materials, sandwich beam

Procedia PDF Downloads 146

Authors: Utsav Bhardwaj, Shyama Prasad Das

Abstract:

To meet the extensive requirements of thermal management of the circuit card assemblies (CCAs), satellites, PCBs, microprocessors, any other electronic circuitry, pulsating heat pipes (PHPs) have emerged in the recent past as one of the best solutions technically. But industrial application of PHPs is still unexplored up to a large extent due to their poor reliability. There are several systems as well as operational parameters which not only affect the performance of an operating PHP, but also decide whether the PHP can operate sustainably or not. Functioning may completely be halted for some particular combinations of the values of system and operational parameters. Among the system parameters, adiabatic length is one of the important ones. In the present work, a simplest single branch PHP system with an adiabatic section has been considered. It is assumed to have only one vapour bubble and one liquid plug. First, the system has been mathematically modeled using film evaporation/condensation model, followed by the steps of recognition of equilibrium zone, non-dimensionalization and linearization. Then proceeding with a periodical solution of the linearized and reduced differential equations, stability analysis has been performed. Slow and fast variables have been identified, and averaging approach has been used for the slow ones. Ultimately, temporal evolution of the PHP is predicted by numerically solving the averaged equations, to know whether the oscillations are likely to sustain/decay temporally. Stability threshold has also been determined in terms of some non-dimensional numbers formed by different groupings of system and operational parameters. A combined analytical and numerical approach has been used, and it has been found that for each combination of all other parameters, there exists a maximum length of the adiabatic section beyond which the PHP cannot function at all. This length has been called as “Critical Adiabatic Length (L_ac)”. For adiabatic lengths greater than “L_ac”, oscillations are found to be always decaying sooner or later. Dependence of “L_ac” on some other parameters has also been checked and correlated at certain evaporator & condenser section temperatures. “L_ac” has been found to be linearly increasing with increase in evaporator section length (L_e), whereas the condenser section length (L_c) has been found to have almost no effect on it upto a certain limit. But at considerably large condenser section lengths, “L_ac” is expected to decrease with increase in “L_c” due to increased wall friction. Rise in static pressure (p_r) exerted by the working fluid reservoir makes “L_ac” rise exponentially whereas it increases cubically with increase in the inner diameter (d) of PHP. Physics of all such variations has been given a good insight too. Thus, a methodology for quantification of the critical adiabatic length for any possible set of all other parameters of PHP has been established.

Keywords: critical adiabatic length, evaporation/condensation, pulsating heat pipe (PHP), thermal management

Procedia PDF Downloads 225

Authors: Crystal Hoole

Abstract:

Employee well-being has become an area of concern for top executives and organizations worldwide. In developing countries such as South Africa, and especially in the educational sector, employees have to deal with anxiety, stress, fear, student protests, political and economic turmoil and excessive work demands on a daily basis. Research has shown that workplaces with higher resilience and better well-being strategies also report higher productivity, increased innovation, better employee retention and better employee engagement. Many organisations offer standard employee assistance programs and once-off short interventions. However, most of these well-being initiatives are perceived as ineffective. Some of the criticism centers around a lack of holistic well-being approaches, no proof of the success of well-being initiatives, not being part of the organization’s strategies and a lack of genuine leadership support. This study attempts to illustrate how a holistic well-being intervention, over a period of 100 days, is far more effective in impacting organizational outcomes. A quasi-experimental design, with a pre-test and pro-test design with a randomization strategy, will be used. Measurements of organizational outcomes are taken at three-time points throughout the study, before, middle and after. The constructs that will be measured are employee engagement, psychological well-being, organizational culture and trust, and perceived stress. The well-being is imitative follows a salutogenesis approach and is aimed at building resilience through focusing on six focal areas, namely sleep, mindful eating, exercise, love, gratitude and appreciation, breath work and mindfulness, and finally, purpose. Certain organizational constructs, including employee engagement, psychological well-being, organizational culture and trust and perceived stress, will be measured at three-time points during the study, namely before, middle and after. A quasi-experimental, pre-test and post-test design will be applied, also using a randomization strategy to limit potential bias. Repeated measure ANCOVA will be used to determine whether any change occurred over the period of 100 days. The study will take place in a Higher Education institution in South Africa. The sample will consist of academic and administrative staff. Participants will be assigned to a test and control group. All participants will complete a survey measuring employee engagement, psychological well-being, organizational culture and trust, and perceived stress. Only the test group will undergo the well-being intervention. The study envisages contributing on several levels: Firstly, the study hopes to find a positive increase in the various well-being indicators of the participants who participated in the study and secondly to illustrate that a longer more holistic approach is successful in improving organisational success (as measured in the various organizational outcomes).

Keywords: wellbeing, resilience, organizational success, intervention

Procedia PDF Downloads 97

Authors: Nadia Arikat, Katharine Blain

Abstract:

During the worst of the COVID pandemic, only essential treatment was provided for patients needing urgent care. With the prolonged extent of the pandemic, there has been a return to more routine referrals for paediatric dentistry advice and treatment for specialist conditions. However, some of these patients and/or their carers may have significant medical issues meaning that attending in-person appointments carries additional risks. This poses an ethical dilemma for clinicians. This project looks at how a secure video conferencing platform (“Near Me”) has been used to assess the need and urgency for in-person new patient visits, particularly for patients and families with additional risks. “Near Me” is a secure online video consulting service used by NHS Scotland. In deciding whether to bring a new patient to the hospital for an appointment, the clinical condition of the teeth together with the urgency for treatment need to be assessed. This is not always apparent from the referral letter. In addition, it is important to judge the risks to the patients and carers of such visits, particularly if they have medical issues. The use and effectiveness of “Near Me” consultations to help decide whether vulnerable paediatric patients should have in-person appointments will be illustrated and discussed using two families: one where the child is medically compromised (Alagille syndrome with previous liver transplant), and the other where there is a medically compromised parent (undergoing chemotherapy and a bone marrow transplant). In both cases, it was necessary to take into consideration the risks and moral implications of requesting that they attend the dental hospital during a pandemic. The option of remote consultation allowed further clinical information to be evaluated and the families take part in the decision-making process about whether and when such visits should be scheduled. These cases will demonstrate how medically compromised patients (or patients with vulnerable carers), could have their dental needs assessed in a socially distanced manner by video consultation. Together, the clinician and the patient’s family can weigh up the risks, with regards to COVID-19, of attending for in-person appointments against the benefit of having treatment. This is particularly important for new paediatric patients who have not yet had a formal assessment. The limitations of this technology will also be discussed. It is limited by internet availability, the strength of the connection, the video quality and families owning a device which allows video calls. For those from a lower socio-economic background or living in some rural areas, this may not be possible or limit its usefulness. For the two patients discussed in this project, where the urgency of their dental condition was unclear, video consultation proved beneficial in deciding an appropriate outcome and preventing unnecessary exposure of vulnerable people to a hospital environment during a pandemic, demonstrating the usefulness of such technology when it is used appropriately.

Keywords: COVID-19, paediatrics, triage, video consultations

Procedia PDF Downloads 97

Authors: Varsha Tol, Laila Garda, Neelam Bhardwaj, Malata Usar

Abstract:

In India, differently- abled girls suffer from a “dual stigma” of being female and physically challenged. The general consensus is that they are incapable of standing on their own two feet. It was observed that these girls do not have access to educational programs as most hostels do not keep them after the tenth grade. They are forced to return to a life of poverty and are often considered a liability by their families. Higher education is completely ignored. Parents focus on finding a husband and passing on their ‘burden’ to someone else. An innovative, intervention for differently-abled adolescent girls with the express purpose of mainstreaming them into society was started by Helplife. The objective was to enrich the lives of these differently abled adolescent girls through precise research, focused intervention and professionalism. This programme addresses physical, mental and social rehabilitation of the girls who come from impoverished backgrounds. These adolescents are reached by word of mouth, snowball technique and through the network of the NGO. Applications are invited from potential candidates which are scrutinized by a panel of experts. Selection criteria include her disability, socio-economic status, and desire and drive to make a difference in her own life. The six main areas of intervention are accommodation, education, health, professional courses, counseling and recreational activities. Each girl on an average resides in Helplife for a period of 2-3 years. Analysis of qualitative data collected at various time points indicates holistic development of character. A quality of life questionnaire showed a significant improvement in scores at three different time points in 75% of the current population under intervention i.e. 19 girls. Till date, 25 girls have successfully passed out from the intervention program completing their graduation/post-graduation. Currently, we have 19 differently abled girls housed in three flats in Pune district of Maharashtra. Out of which 14 girls are pursuing their graduation or post-graduation. Six of the girls are working in jobs in various sectors. In conclusion it may be noted with adequate support and guidance the sky is the limit. This journey of 12 years has been a learning for us with ups and downs modifying the intervention at every step. Helplife has a belief of impacting positively, individual lives of differently abled girls in order to empower them in a holistic manner. The intervention has a positive impact on differently abled girls. They serve as role models to other differently abled girls indicating that this is a road map to success by getting empowered to live with full potential and get integrated in the society in a dignified way.

Keywords: differently-abled, dual-stigma, empowerment, youth

Procedia PDF Downloads 171

Authors: M. S. Stepanova, V. V. Zakharov, P. D. Khavlyuk, I. D. Skurlov, A. Y. Dubovik, A. L. Rogach

Abstract:

Carbon dots are small carbon-based spherical nanoparticles, which are typically less than 10 nm in size that can be modified with surface passivation and heteroatoms doping. The light-absorbing ability of carbon dots has attracted a significant amount of attention in photoluminescence for bioimaging and fluorescence sensing applications owing to their advantages, such as tunable fluorescence emission, photo- and thermostability and low toxicity. In this study, carbon dots were synthesized by the solvothermal method from citric acid and ethylenediamine dissolved in water. The solution was heated for 5 hours at 200°C and then cooled down to room temperature. The carbon dots films were obtained by evaporation from a high-concentration aqueous solution. The increase of both luminescence intensity and light transmission was obtained as a result of a 405 nm laser exposure to a part of the carbon dots film, which was detected using a confocal laser scanning microscope (LSM 710, Zeiss). Blueshift up to 35 nm of the luminescence spectrum is observed as luminescence intensity, which is increased more than twofold. The exact value of the shift depends on the time of the laser exposure. This shift can be caused by the modification of surface groups at the carbon dots, which are responsible for long-wavelength luminescence. In addition, a shift of the absorption peak by 10 nm and a decrease in the optical density at the wavelength of 350 nm is detected, which is responsible for the absorption of surface groups. The obtained sample was also studied with time-resolved confocal fluorescence microscope (MicroTime 100, PicoQuant), which made it possible to receive a time-resolved photoluminescence image and construct emission decays of the laser-exposed and non-exposed areas. 5 MHz pulse rate impulse laser has been used as a photoluminescence excitation source. Photoluminescence decay was approximated by two exhibitors. The laser-exposed area has the amplitude of the first-lifetime component (A1) twice as much as before, with increasing τ1. At the same time, the second-lifetime component (A2) decreases. These changes evidence a modification of the surface groups of carbon dots. The detected effect can be used to create thermostable fluorescent marks, the physical size of which is bounded by the diffraction limit of the optics (~ 200-300 nm) used for exposure and to improve the optical properties of carbon dots or in the field of optical encryption. Acknowledgements: This work was supported by the Ministry of Science and Higher Education of Russian Federation, goszadanie no. 2019-1080 and financially supported by Government of Russian Federation, Grant 08-08.

Keywords: carbon dots, photoactivation, optical properties, photoluminescence and absorption spectra

Procedia PDF Downloads 162

Authors: Arif Tri Setyanto, Aditya Nanda Priyatama, Nugraha Arif Karyanta, Fadjri Kirana A., Afia Fitriani, Rini Setyowati, Moh.Abdul Hakim

Abstract:

The Basic Health Research Report by the Ministry of Health (2018) shows an increase in the prevalence of mental health disorders in the adolescent and early adult age ranges. Supporting this finding, data on the psychological examination of the student health service unit at one State University recorded 115 cases of moderate and severe health problems in the period 2016 - 2019. More specifically, the highest number of cases was experienced by clients in the age range of 21-23 years or equivalent, with the mid-semester stage towards the end. Based on the distribution of cases experienced and the disorder becomes a psychological problem experienced by students. A total of 29% or the equivalent of 33 students experienced anxiety disorders, 25% or 29 students experienced problems ranging from mild to severe, as well as other classifications of disorders experienced, including adjustment disorders, family problems, academics, mood disorders, self-concept disorders, personality disorders, cognitive disorders, and others such as trauma and sexual disorders. Various mental health disorders have a significant impact on the academic life of students, such as low GPA, exceeding the limit in college, dropping out, disruption of social life on campus, to suicide. Based on literature reviews and best practices from universities in various countries, one of the effective ways to prevent and treat student mental health disorders is to implement a mental health monitoring system in universities. This study uses a participatory action research approach, with a sample of 423 from a total population of 32,112 students. The scale used in this study is the Beck Depression Inventory (BDI) to measure depression and the Taylor Minnesota Anxiety Scale (TMAS) to measure anxiety levels. This study aims to (1) develop a digital-based health monitoring system for students' mental health situations in the mental health category. , dangers, or those who have mental disorders, especially indications of symptoms of depression and anxiety disorders, and (2) implementing a mental health monitoring system in universities at the beginning and end of each semester. The results of the analysis show that from 423 respondents, the main problems faced by all coursework, such as thesis and academic assignments. Based on the scoring and categorization of the Beck Depression Inventory (BDI), 191 students experienced symptoms of depression. A total of 24.35%, or 103 students experienced mild depression, 14.42% (61 students) had moderate depression, and 6.38% (27 students) experienced severe or extreme depression. Furthermore, as many as 80.38% (340 students) experienced anxiety in the high category. This article will review this review of the student mental health service system on campus.

Keywords: monitoring system, mental health, psychological problems, students

Procedia PDF Downloads 109

Authors: Heba Salama, Barry Gibson, Jennifer Burr

Abstract:

Introduction: It is often argued that better oral health leads to better wellbeing, and the goal of dental care is to improve wellbeing. Notwithstanding, to our best knowledge, there is a lack of evidence to support the relationship between oral health and wellbeing. Aim: The scoping review aims to examine current definitions of health and wellbeing as well as map the evidence to examine the relationship between oral health and wellbeing. Methods: The scoping review followed the Preferred Reporting Items for Systematic Reviews Extension for Scoping Review (PRISMA-ScR). A two-phase search strategy was followed because of the unmanageable number of hits returned. The first phase was to identify how well-being was conceptualised in oral health literacy, and the second phase was to search for extracted keywords. The extracted keywords were searched in four databases: PubMed, CINAHL, PsycINFO, and Web of Science. To limit the number of studies to a manageable amount, the search was limited to the open-access studies that have been published in the last five years (from 2018 to 2022). Results: Only eight studies (0.1%) of the 5455 results met the review inclusion criteria. Most of the included studies defined wellbeing based on the hedonic theory. And the Satisfaction with Life Scale is the most used. Although the research results are inconsistent, it has generally been shown that there is a weak or no association between oral health and wellbeing. Interpretation: The review revealed a very important point about how oral health literature uses loose definitions that have significant implications for empirical research. That results in misleading evidence-based conclusions. According to the review results, improving oral health is not a key factor in improving wellbeing. It appears that investing in oral health care to improve wellbeing is not a top priority to tell policymakers about. This does not imply that there should be no investment in oral health care to improve oral health. That could have an indirect link to wellbeing by eliminating the potential oral health-related barriers to quality of life that could represent the foundation of wellbeing. Limitation: Only the most recent five years (2018–2022), peer-reviewed English-language literature, and four electronic databases were included in the search. These restrictions were put in place to keep the volume of literature at a manageable level. This suggests that some significant studies might have been omitted. Furthermore, the study used a definition of wellbeing that is currently being evolved and might not everyone agrees with it. Conclusion: Whilst it is a ubiquitous argument that oral health is related to wellbeing, and this seems logical, there is little empirical evidence to support this claim. This question, therefore, requires much more detailed consideration. Funding: This project was funded by the Ministry of Higher Education and Scientific Research in Libya and Tripoli University.

Keywords: oral health, wellbeing, satisfaction, emotion, quality of life, oral health related quality of life

Procedia PDF Downloads 118

Authors: Loukou Amoin Marie Djedri

Abstract:

Financing is important for all terrorists – from the largest organizations in control of territories, to the smallest groups – not only for spreading fear through attacks, but also to finance the expansion of terrorist dogmas. These organizations pose serious threats to the international community. The disruption of terrorist financing aims to create a hostile environment for the growth of terrorism and to limit considerably the terrorist groups capacities. The World Bank (WB), together with the International Monetary Fund (IMF), decided to include in their scope the Fight against the money laundering and the financing of terrorism, in order to assist Member States in protecting their internal financial system from terrorism use and abuse and reinforcing their legal system. To do so, they have adopted the Anti-Money Laundering /Combating Financing of Terrorism (AML/CFT) standards that have been set up by the Financial Action Task Force. This set of standards, recognized as the international standards for anti-money laundering and combating the financing of terrorism, has to be implemented by States Members in order to strengthen their judicial system and relevant national institutions. However, we noted that, to date, some States Members still have significant AML/CFT deficiencies, which can constitute serious threats not only to the country’s economic stability but also for the global financial system. In addition, studies stressed out that repressive measures are more implemented by countries than preventive measures, which could be an important weakness in a state security system. Furthermore, we noticed that the AML/CFT standards evolve slowly, while techniques used by terrorist networks keep developing. The goal of the study is to show how to enhance the AML/CFT global compliance through the work of the IMF and the WB, to help member states to consolidate their financial system. To encourage and ensure the effectiveness of these standards, a methodology for assessing the compliance with the AML/CFT standards has been created to follow up the concrete implementation of these standards and to provide accurate technical assistance to countries in need. A risk-based approach has also been adopted as a key component of the implementation of the AML/CFT Standards, with the aim of strengthening the efficiency of the standards. Instead, we noted that the assessment is not efficient in the process of enhancing AML/CFT measures because it seems to lack of adaptation to the country situation. In other words, internal and external factors are not enough taken into account in a country assessment program. The purpose of this paper is to analyze the AML/CFT regime in the fight against the financing of terrorism and to find lasting solutions to achieve the global AML/CFT compliance. The work of all the organizations involved in this combat is imperative to protect the financial network and to lead to the disintegration of terrorist groups in the future.

Keywords: AML/CFT standards, financing of terrorism, international financial institutions, risk-based approach

Procedia PDF Downloads 275

Authors: Mahtab Abdollahi Sarvi, Siamak Epackachi, Ali Imanpour

Abstract:

Reinforced concrete shear walls are commonly used as the lateral load-resisting system of mid- to high-rise office or residential buildings around the world. Design of such systems is often governed by wind rather than seismic effects, in particular in low-to-moderate seismic regions. The current design philosophy as per the majority of building codes under wind loads require elastic response of lateral load-resisting systems including reinforced concrete shear walls when subjected to the rare design wind load, resulting in significantly large wall sections needed to meet strength requirements and drift limits. The latter can highly influence the design in upper stories due to stringent drift limits specified by building codes, leading to substantial added costs to the construction of the wall. However, such walls may offer limited to moderate over-strength and ductility due to their large reserve capacity provided that they are designed and detailed to appropriately develop such over-strength and ductility under extreme wind loads. This would significantly contribute to reducing construction time and costs, while maintaining structural integrity under gravity and frequently-occurring and less frequent wind events. This paper aims to investigate the over-strength and ductility capacity of several imaginary office buildings located in Edmonton, Canada with a glance at earthquake design philosophy. Selected models are 10- to 25-story buildings with three types of reinforced concrete shear wall configurations including rectangular, barbell, and flanged. The buildings are designed according to National Building Code of Canada. Then fiber-based numerical models of the walls are developed in Perform 3D and by conducting nonlinear static (pushover) analysis, lateral nonlinear behavior of the walls are evaluated. Ductility and over-strength of the structures are obtained based on the results of the pushover analyses. The results confirmed moderate nonlinear capacity of reinforced concrete shear walls under extreme wind loads. This is while lateral displacements of the walls pass the serviceability limit states defined in Pre standard for Performance-Based Wind Design (ASCE). The results indicate that we can benefit the limited nonlinear response observed in the reinforced concrete shear walls to economize the design of such systems under wind loads.

Keywords: concrete shear wall, high-rise buildings, nonlinear static analysis, response modification factor, wind load

Procedia PDF Downloads 105

Authors: Toslim Uddin Khan, Jesmin Akter, Mohiuddin Ahmed

Abstract:

Menstrual hygiene management (MHM) and personal health-care practice is a critical issue to prevent morbidity and other reproductive health complications among adolescent girls in Bangladesh. Inadequate access to water, sanitation and hygiene (WASH) facilities lead to unhealthy MHM practices that resulted in poor reproductive health outcomes. It is evident from different studies that superstitions and misconception are more common in rural communities that limit young girls’ access to and understanding of the menstrual hygiene and self care practices. The state-of-the-art approach of Social Marketing Company (SMC) is proved to be instrumental in delivering reinforcing health messages, making public health and hygiene products available at the door steps of the community through community mobilization programs in rural Bangladesh. School health program is one of the flagship interventions of SMC to equip adolescent girls and boys with correct knowledge of health and hygiene practices among themselves, their families and peers. In Bangladeshi culture, adolescent girls often feel shy to ask fathers or male family members about buying sanitary napkin from local pharmacy and they seem to be reluctant to seek help regarding their menstrual problems. A recent study reveals that 48% adolescent girls are using sanitary napkins while majority of them are unaware of menstrual hygiene practices in Bangladesh. Under school adolescent program, SMC organizes health education sessions for adolescent girls from grade seven to ten using enter-educate approach with special focus on sexual and reproductive health and menstrual hygiene issues including delaying marriage and first pregnancy. In addition, 2500 rural women entrepreneurs branded as community sales agents are also involved in disseminating health messages and selling priority health products including sanitary napkin at the household level. These women entrepreneurs are serving as a source of sustainable supply of the sanitary napkins for the rural adolescent girls and thereby they are earning profit margins on the sales they make. A recent study on the impact of adolescent program activities reveals that majority (71%) of the school adolescent girls are currently using sanitary napkins. Health education equips and empowers adolescent girls with accurate knowledge about menstrual hygiene practices and self-care as well. Therefore, engagement of female entrepreneurs in school adolescent health program at the community level is one of the promising ways to improve menstrual hygiene practices leading to increased use of sanitary napkin in rural and semi-rural communities in Bangladesh.

Keywords: school adolescent program, social marketing, women entrepreneurs, menstrual hygiene management

Procedia PDF Downloads 195

Authors: Mishell E. Cabrera, Bryan G. Valencia, Anderson I. Guamán

Abstract:

Human dependence on plastic products has led to global pollution, with plastic particles ranging in size from 0.001 to 5 millimeters, which are called microplastics (hereafter, MPs). The abundance of microplastics is used as an indicator of pollution. However, reports of pollution (abundance of MPs) in river sediments do not consider that the accumulation of sediments and MPs depends on the energy of the river. That is, the abundance of microplastics will be underestimated if the sediments analyzed come from places where the river flows with a lot of energy, and the abundance will be overestimated if the sediment analyzed comes from places where the river flows with less energy. This bias can generate an error greater than 300% of the MPs value reported for the same river and should increase when comparisons are made between 2 rivers with different characteristics. Sections where the river flows with higher energy allow sands to be deposited and limit the accumulation of MPs, while sections, where the same river has lower energy, allow fine sediments such as clays and silts to be deposited and should facilitate the accumulation of MPs particles. That is, the abundance of MPs in the same river is underrepresented when the sediment analyzed is sand, and the abundance of MPs is overrepresented if the sediment analyzed is silt or clay. The present investigation establishes a protocol aimed at incorporating sample granulometry to calibrate MPs quantification and eliminate over- or under-representation bias (hereafter granulometric bias). A total of 30 samples were collected by taking five samples within six work zones. The slope of the sampling points was less than 8 degrees, referred to as low slope areas, according to the Van Zuidam slope classification. During sampling, blanks were used to estimate possible contamination by MPs during sampling. Samples were dried at 60 degrees Celsius for three days. A flotation technique was employed to isolate the MPs using sodium metatungstate with a density of 2 gm/l. For organic matter digestion, 30% hydrogen peroxide and Fenton were used at a ratio of 6:1 for 24 hours. The samples were stained with rose bengal at a concentration of 200 mg/L and were subsequently dried in an oven at 60 degrees Celsius for 1 hour to be identified and photographed in a stereomicroscope with the following conditions: Eyepiece magnification: 10x, Zoom magnification (zoom knob): 4x, Objective lens magnification: 0.35x for analysis in ImageJ. A total of 630 fibers of MPs were identified, mainly red, black, blue, and transparent colors, with an overall average length of 474,310 µm and an overall median length of 368,474 µm. The particle size of the 30 samples was calculated using 100 g per sample using sieves with the following apertures: 2 mm, 1 mm, 500 µm, 250 µm, 125 µm and 0.63 µm. This sieving allowed a visual evaluation and a more precise quantification of the microplastics present. At the same time, the weight of sediment in each fraction was calculated, revealing an evident magnitude: as the presence of sediment in the < 63 µm fraction increases, a significant increase in the number of MPs particles is observed.

Keywords: microplastics, pollution, sediments, Tena River

Procedia PDF Downloads 71

Authors: Thelma Maria Melo Pinheiro, Guilherme Raposo Diniz Vieira, Sidney Matos da Silva, Leonardo Mendonça de Oliveira Queiroz, Mateus Sousa Pinheiro, Danyllo Wenceslau de Oliveira Lopes

Abstract:

The present article has the objective to describe the regulatory impact analysis (RIA) of the contracting efficiency of the Brazilian transmission system usage. This contracting is made by users connected to the main transmission network and is used to guide necessary investments to supply the electrical energy demand. Therefore, an inefficient contracting of this energy amount distorts the real need for grid capacity, affecting the sector planning accuracy and resources optimization. In order to provide this efficiency, the Brazilian Electricity Regulatory Agency (ANEEL) homologated the Normative Resolution (NR) No. 666, from July 23th of 2015, which consolidated the procedures for the contracting of transmission system usage and the contracting efficiency verification. Aiming for a more efficient and rational transmission system contracting, the resolution established economic incentives denominated as Inefficiency installment for excess (IIE) and inefficiency installment for over-contracting (IIOC). The first one, IIE, is verified when the contracted demand exceeds the established regulatory limit; it is applied to consumer units, generators, and distribution companies. The second one, IIOC, is verified when the distributors over-contract their demand. Thus, the establishment of the inefficiency installments IIE and IIOC intends to avoid the agent contract less energy than necessary or more than it is needed. Knowing that RIA evaluates a regulatory intervention to verify if its goals were achieved, the results from the application of the above-mentioned normative resolution to the Brazilian transmission sector were analyzed through indicators that were created for this RIA to evaluate the contracting efficiency transmission system usage, using real data from before and after the homologation of the normative resolution in 2015. For this, indicators were used as the efficiency contracting indicator (ECI), excess of demand indicator (EDI), and over-contracting of demand indicator (ODI). The results demonstrated, through the ECI analysis, a decrease of the contracting efficiency, a behaviour that was happening even before the normative resolution of 2015. On the other side, the EDI showed a considerable decrease in the amount of excess for the distributors and a small reduction for the generators; moreover, the ODI notable decreased, which optimizes the usage of the transmission installations. Hence, with the complete evaluation from the data and indicators, it was possible to conclude that IIE is a relevant incentive for a more efficient contracting, indicating to the agents that their contracting values are not adequate to keep their service provisions for their users. The IIOC also has its relevance, to the point that it shows to the distributors that their contracting values are overestimated.

Keywords: contracting, electricity regulation, evaluation, regulatory impact analysis, transmission power system

Procedia PDF Downloads 118

Authors: Thomas Larm, Anna Wahlsten

Abstract:

An international literature study has been carried out for comparison of commonly used methods for the dimensioning of transport systems and stormwater facilities for flow detention. The focus of the literature study regarding the calculation of design flow and detention has been the widely used Rational method and its underlying parameters. The impact of chosen design parameters such as return time, rain intensity, runoff coefficient, and climate factor have been studied. The parameters used in the calculations have been analyzed regarding how they can be calculated and within what limits they can be used. Data used within different countries have been specified, e.g., recommended rainfall return times, estimated runoff times, and climate factors used for different cases and time periods. The literature study concluded that the determination of runoff coefficients is the most uncertain parameter that also affects the calculated flow and required detention volume the most. Proposals have been developed for new runoff coefficients, including a new proposed method with equations for calculating runoff coefficients as a function of return time (years) and rain intensity (l/s/ha), respectively. Suggestions have been made that it is recommended not to limit the use of the Rational Method to a specific catchment size, contrary to what many design manuals recommend, with references to this. The proposed relationships between return time or rain intensity and runoff coefficients need further investigation and to include the quantification of uncertainties. Examples of parameters that have not been considered are the influence on the runoff coefficients of different dimensioning rain durations and the degree of water saturation of green areas, which will be investigated further. The influence of climate effects and design rain on the dimensioning of the stormwater facilities grassed ditches and biofilters (bio retention systems) has been studied, focusing on flow detention capacity. We have investigated how the calculated runoff coefficients regarding climate effect and the influence of changed (increased) return time affect the inflow to and dimensioning of the stormwater facilities. We have developed a smart design of ditches and biofilters that results in both high treatment and flow detention effects and compared these with the effect from dry and wet ponds. Studies of biofilters have generally before focused on treatment of pollutants, but their effect on flow volume and how its flow detention capability can improve is only rarely studied. For both the new type of stormwater ditches and biofilters, it is required to be able to simulate their performance in a model under larger design rains and future climate, as these conditions cannot be tested in the field. The stormwater model StormTac Web has been used on case studies. The results showed that the new smart design of ditches and biofilters had similar flow detention capacity as dry and wet ponds for the same facility area.

Keywords: runoff coefficients, flow detention, smart design, biofilter, ditch

Procedia PDF Downloads 85

Authors: Hetvi Trivedi

Abstract:

Technological escalation cannot be negated. The same is true for the benefits of technology. However, such escalation has interfered with the traditional theories of protection under Intellectual Property Rights. Out of the many trends that have disrupted the old-school understanding of Intellectual Property Rights, one is hashtags. What began modestly in the year 2007 has now earned a remarkable status, and coupled with the unprecedented rise in social media the hashtag culture has witnessed a monstrous growth. A tiny symbol on the keypad of phones or computers is now a major trend which also serves companies as a critical investment measure in establishing their brand in the market. Due to this a section of the Intellectual Property Rights- Trademarks is undergoing a humungous transformation with hashtags like #icebucket, #tbt or #smilewithacoke, getting trademark protection. So, as the traditional theories of IP take on the modern trends, it is necessary to understand the change and challenge at a theoretical and proportional level and where need be, question the change. Traditionally, Intellectual Property Rights serves the societal need for intellectual productions that ensure its holistic development as well as cultural, economic, social and technological progress. In a two-pronged effort at ensuring continuity of creativity, IPRs recognize the investment of individual efforts that go into creation by way of offering protection. Commonly placed under two major theories- Utilitarian and Natural, IPRs aim to accord protection and recognition to an individual’s creation or invention which serve as an incentive for further creations or inventions, thus fully protecting the creative, inventive or commercial labour invested in the same. In return, the creator by lending the public the access to the creation reaps various benefits. This way Intellectual Property Rights form a ‘social contract’ between the author and society. IPRs are similarly attached to a social function, whereby individual rights must be weighed against competing rights and to the farthest limit possible, both sets of rights must be treated in a balanced manner. To put it differently, both the society and the creator must be put on an equal footing with neither party’s rights subservient to the other. A close look through doctrinal research, at the recent trend of trademark protection, makes the social function of IPRs seem to be moving far from the basic philosophy. Thus, where technology interferes with the philosophies of law, it is important to check and allow such growth only in moderation, for none is superior than the other. The human expansionist nature may need everything under the sky that can be tweaked slightly to be counted and protected as Intellectual Property- like a common parlance word transformed into a hashtag, however IP in order to survive on its philosophies needs to strike a balance. A unanimous global decision on the judicious use of IPR recognition and protection is the need of the hour.

Keywords: hashtag trademarks, intellectual property, social function, technology

Procedia PDF Downloads 131

Authors: Cagri Baris Kasap

Abstract:

In this study, how interface designers can be viewed as producers of culture in the current era will be interrogated from a critical theory perspective. Walter Benjamin was a German Jewish literary critical theorist who, during 1930s, was engaged in opposing and criticizing the Nazi use of art and media. ‘The Author as Producer’ is an essay that Benjamin has read at the Communist Institute for the Study of Fascism in Paris. In this article, Benjamin relates directly to the dialectics between base and superstructure and argues that authors, normally placed within the superstructure should consider how writing and publishing is production and directly related to the base. Through it, he discusses what it could mean to see author as producer of his own text, as a producer of writing, understood as an ideological construct that rests on the apparatus of production and distribution. So Benjamin concludes that the author must write in ways that relate to the conditions of production, he must do so in order to prepare his readers to become writers and even make this possible for them by engineering an ‘improved apparatus’ and must work toward turning consumers to producers and collaborators. In today’s world, it has become a leading business model within Web 2.0 services of multinational Internet technologies and culture industries like Amazon, Apple and Google, to transform readers, spectators, consumers or users into collaborators and co-producers through platforms such as Facebook, YouTube and Amazon’s CreateSpace Kindle Direct Publishing print-on-demand, e-book and publishing platforms. However, the way this transformation happens is tightly controlled and monitored by combinations of software and hardware. In these global-market monopolies, it has become increasingly difficult to get insight into how one’s writing and collaboration is used, captured, and capitalized as a user of Facebook or Google. In the lens of this study, it could be argued that this criticism could very well be considered by digital producers or even by the mass of collaborators in contemporary social networking software. How do software and design incorporate users and their collaboration? Are they truly empowered, are they put in a position where they are able to understand the apparatus and how their collaboration is part of it? Or has the apparatus become a means against the producers? Thus, when using corporate systems like Google and Facebook, iPhone and Kindle without any control over the means of production, which is closed off by opaque interfaces and licenses that limit our rights of use and ownership, we are already the collaborators that Benjamin calls for. For example, the iPhone and the Kindle combine a specific use of technology to distribute the relations between the ‘authors’ and the ‘prodUsers’ in ways that secure their monopolistic business models by limiting the potential of the technology.

Keywords: interface designer, cultural producer, Walter Benjamin, materialist aesthetics, dialectical thinking

Procedia PDF Downloads 142

Authors: Majid Farsadrouh Rashti, Alireza Mohammadinejad, Amir Shafiee Kisomi

Abstract:

Lead (Pb²⁺), a cation, is a prime constituent of the majority of the industrial effluents such as mining, smelting and coal combustion, Pb-based painting and Pb containing pipes in water supply systems, paper and pulp refineries, printing, paints and pigments, explosive manufacturing, storage batteries, alloy and steel industries. The maximum permissible limit of lead in the water used for drinking and domesticating purpose is 0.01 mg/L as advised by Bureau of Indian Standards, BIS. This becomes the acceptable 'safe' level of lead(II) ions in water beyond which, the water becomes unfit for human use and consumption, and is potential enough to lead health problems and epidemics leading to kidney failure, neuronal disorders, and reproductive infertility. Superabsorbent hydrogels are loosely crosslinked hydrophilic polymers that in contact with aqueous solution can easily water and swell to several times to their initial volume without dissolving in aqueous medium. Superabsorbents are kind of hydrogels capable to swell and absorb a large amount of water in their three-dimensional networks. While the shapes of hydrogels do not change extensively during swelling, because of tremendously swelling capacity of superabsorbent, their shape will broadly change.Because of their superb response to changing environmental conditions including temperature pH, and solvent composition, superabsorbents have been attracting in numerous industrial applications. For instance, water retention property and subsequently. Natural-based superabsorbent hydrogels have attracted much attention in medical pharmaceutical, baby diapers, agriculture, and horticulture because of their non-toxicity, biocompatibility, and biodegradability. Novel superabsorbent hydrogel nanocomposites were prepared by graft copolymerization of acrylamide and itaconic acid in the presence of nanoclay (laponite), using methylene bisacrylamide (MBA) and potassium persulfate, former as a crosslinking agent and the second as an initiator. The superabsorbent hydrogel nanocomposites structure was characterized by FTIR spectroscopy, SEM and TGA Spectroscopy adsorption of metal ions on poly (AAm-co-IA). The equilibrium swelling values of copolymer was determined by gravimetric method. During the adsorption of metal ions on polymer, residual metal ion concentration in the solution and the solution pH were measured. The effects of the clay content of the hydrogel on its metal ions uptake behavior were studied. The NC hydrogels may be considered as a good candidate for environmental applications to retain more water and to remove heavy metals.

Keywords: adsorption, hydrogel, nanocomposite, super adsorbent

Procedia PDF Downloads 187

Authors: Tan Hui Ying Renee, Stella Rizalina Sasha, Farah Safdar Husain

Abstract:

Introduction: Menopause Hormone Therapy (MHT) is an effective drug indicated for the treatment of menopausal symptoms and as replacement therapy in women who undergo premature menopause. In 2020, less than 8.8% of perimenopausal Singaporean women are on hormonal therapy, as compared to the Western population, where up to 50% may be on MHT. Factors associated with MHT utilization have been studied from patient characteristics, but the impact of locally prescribing physicians resulting in low MHT utilization has yet to be evaluated. The aim of the study is to determine the level of knowledge physicians in the Obstetrics and Gynaecology specialty have and their attitudes toward MHT. We believe that knowledge of MHT is lacking and that negative attitudes towards MHT may influence its use and undermine the benefits MHT may have for women. This paper is a part of a larger study on Singaporean physicians’ knowledge and attitudes towards MHT. Methods: This is a cross-sectional study intended to assess the knowledge and attitudes of physicians toward Menopausal Hormone Therapy. An anonymous questionnaire was disseminated via institutional internal circulations to optimize reach to physicians who may prescribe MHT, particularly in the fields of Gynaecology, Family Medicine and Endocrinology. Responses were completed voluntarily. Physicians had the option for each question to declare that they were ‘unsure’ or that the question was ‘beyond their expertise’. 21 knowledge questions tested factual recall on indications, contraindications, and risks of MHT. The remaining 6 questions were clinical scenarios crafted with the intention of testing specific principles related to the use of MHT. These questions received face validation from experts in the field. 198 responses were collected, 79 of which were from physicians in the Obstetrics and Gynaecology specialty. The data will be statistically analyzed to investigate areas that can be improved to increase the overall benefits of MHT for the Singaporean population. Results: Preliminary results show that the prevailing factors that limit Singaporean gynecologists and obstetricians from prescribing MHT are a lack of knowledge of MHT and a lack of confidence in prescribing MHT. Risks and indications of MHT were not well known by many physicians, with the majority of the questions having more than 25% incorrect and ‘unsure’ as their reply. The clinical scenario questions revealed significant shortcomings in knowledge on how to navigate real-life challenges in MHT use, with 2 of 6 questions with more than 50% incorrect or ‘beyond their expertise’ as their reply. The portion of the questionnaire that investigated the attitudes of physicians showed that though a large majority believed MHT to be an effective drug, only 40.5% were confident in prescribing it. Conclusion: Physicians in the Obstetrics and Gynaecology specialty lack knowledge and confidence in MHT. Therefore, it is imperative to formulate solutions on both the individual and institutional levels to fill these gaps and ensure that MHT is used appropriately and prescribed to the patients who need it.

Keywords: menopause, menopause hormone therapy, physician factors, obstetrics and gynecology, menopausal symptoms, Singapore

Procedia PDF Downloads 39

Authors: Tin Yee Ling, Kavita Maravar, Ruzica Ardalic

Abstract:

Background: Uterine torsion (UT) in pregnancy of more than 45-degree along the longitudinal axis is a rare occurrence, and the aetiology remains unclear. Case: A 34-year-old G2P1 woman with a history of one previous caesarean section presented at 36+2 weeks with sudden onset lower abdominal pain, syncopal episode, and tender abdomen on examination. She was otherwise haemodynamically stable. Cardiotocography showed a pathological trace with initial prolonged bradycardia followed by a subsequent tachycardia with reduced variability. An initial diagnosis of uterine dehiscence was made, given the history and clinical presentation. She underwent an emergency caesarean section which revealed a 180-degree UT along the longitudinal axis, with oedematous left round ligament lying transverse anterior to the uterus and a segment of large bowel inferior to the round ligament. Detorsion of uterus was performed prior to delivery of the foetus, and anterior uterine wall was intact with no signs of rupture. There were no anatomical uterine abnormalities found other than stretched left ovarian and round ligaments, which were repaired. Delivery was otherwise uneventful, and she was discharged on day 2 postpartum. Discussion: UT is rare as the number of reported cases is within the few hundreds worldwide. Generally, the uterus is supported in place by uterine ligaments, which limit the mobility of the structure. The causes of UT are unknown, but risk factors such as uterine abnormalities, increased uterine ligaments’ flexibility in pregnancy, and foetal malposition has been identified. UT causes occlusion of uterine vessels, which can lead to ischaemic injury of the placenta causing premature separation of the placenta, preterm labour, and foetal morbidity and mortality if delivery is delayed. Diagnosing UT clinically is difficult as most women present with symptoms similar to placenta abruption or uterine rupture (abdominal pain, vaginal bleeding, shock), and one-third are asymptomatic. The management of UT involves surgical detorsion of the uterus and delivery of foetus via caesarean section. Extra vigilance should be taken to identify the anatomy of the uterus experiencing torsion prior to hysterotomy. There have been a few cases reported with hysterotomy on posterior uterine wall for delivery of foetus as it may be difficult to identify and reverse a gravid UT when foetal well-being is at stake. Conclusion: UT should be considered a differential diagnosis of acute abdominal pain in pregnancy. It is crucial that the torsion is addressed immediately as it is associated with maternal and foetal morbidity and mortality.

Keywords: uterine torsion, pregnancy complication, abdominal pain, torted uterus

Procedia PDF Downloads 160

Authors: Sara E. Baumann, Megan A. Rabin, Mary Hawk, Bhimsen Devkota, Kajol Upadhyaya, Guna Raj Shrestha, Brigit Joseph, Annika Agarwal, Jessica G. Burke

Abstract:

In Nepal, prevailing sociocultural norms associated with menstruation prompt adherence to stringent rules that limit participation in daily activities. Chhaupadi is a specific menstrual tradition in Nepal in which women and girls segregate themselves and follow a series of restrictions during menstruation. Despite having numerous physical and mental health implications, extant interventions have yet to sustainably address the harms associated with chhaupadi. In this study, the authors describe insights garnered from a collaboration with community members in Dailekh district, who formulated their own approaches to mitigate the adverse facets of chhaupadi. Envisaged as an entry point to improve women’s menstrual health experiences, this investigation employed an approach that uses Human-centered Design and a community-engaged approach. The authors conducted a four-day design workshop which unfolded in two phases: The Discovery Phase, to uncover chhaupadi context and key stakeholders, and the Design Phase, to design contextually relevant interventions. Diverse community-members, including those with lived experience practicing chhaupadi, developed five intervention concepts: 1) harnessing Female Community Health Volunteers as role models, for counseling, and raising awareness; 2) focusing on mothers and mother’s groups to instigate behavioral shifts; 3) engaging the broader community in behavior change efforts; 4) empowering fathers to effect change in their homes through counseling and education; and 5) training and emboldening youth to advocate for positive change through advocacy in their schools and homes. This research underscores the importance of employing multi-level approaches tailored to specific stakeholder groups, given Nepal’s rich cultural diversity. The engagement of Female Community Health Volunteers emerged as a promising yet underexplored intervention concept for chhaupadi, warranting broader implementation. Crucially, it is also imperative for interventions to prioritize tackling deleterious aspects of the chhaupadi tradition, emphasizing safety considerations, all while acknowledging chhaupadi’s entrenched cultural history; for some, there are positive aspects of the tradition that women and girls wish to preserve.

Keywords: human-centered design, menstrual health, Nepal, community-engagement, intervention development, women's health, rural health

Procedia PDF Downloads 61