Search results for: conflict at work
6289 Control Flow around NACA 4415 Airfoil Using Slot and Injection
Authors: Imine Zakaria, Meftah Sidi Mohamed El Amine
Abstract:
One of the most vital aerodynamic organs of a flying machine is the wing, which allows it to fly in the air efficiently. The flow around the wing is very sensitive to changes in the angle of attack. Beyond a value, there is a phenomenon of the boundary layer separation on the upper surface, which causes instability and total degradation of aerodynamic performance called a stall. However, controlling flow around an airfoil has become a researcher concern in the aeronautics field. There are two techniques for controlling flow around a wing to improve its aerodynamic performance: passive and active controls. Blowing and suction are among the active techniques that control the boundary layer separation around an airfoil. Their objective is to give energy to the air particles in the boundary layer separation zones and to create vortex structures that will homogenize the velocity near the wall and allow control. Blowing and suction have long been used as flow control actuators around obstacles. In 1904 Prandtl applied a permanent blowing to a cylinder to delay the boundary layer separation. In the present study, several numerical investigations have been developed to predict a turbulent flow around an aerodynamic profile. CFD code was used for several angles of attack in order to validate the present work with that of the literature in the case of a clean profile. The variation of the lift coefficient CL with the momentum coefficientKeywords: CFD, control flow, lift, slot
Procedia PDF Downloads 1836288 On the Effects of External Cross-Flow Excitation Forces on the Vortex-Induced-Vibrations of an Oscillating Cylinder
Authors: Abouzar Kaboudian, Ravi Chaithanya Mysa, Boo Cheong Khoo, Rajeev Kumar Jaiman
Abstract:
Vortex induced vibrations can significantly affect the effectiveness of structures in aerospace as well as offshore marine industries. The oscillatory nature of the forces resulting from the vortex shedding around bluff bodies can result in undesirable effects such as increased loading, stresses, deflections, vibrations and noise in the structures, and also reduced fatigue life of the structures. To date, most studies concentrate on either the free oscillations or the prescribed motion of the bluff bodies. However, the structures in operation are usually subject to the external oscillatory forces (e.g. due to the platform motions in offshore industries). In this work, we present the effects of the external cross-flow forces on the vortex-induced vibrations of an oscillating cylinder. The effects of the amplitude, as well as the frequency of the external force on the fluid-forces on the oscillating cylinder are carefully studied and presented. Moreover, we present the transition of the response to be dominated by the vortex-induced-vibrations to the range where it is mostly dictated by the external oscillatory forces. Furthermore, we will discuss how the external forces can affect the flow structures around a cylinder. All results are compared against free oscillations of the cylinder.Keywords: circular cylinder, external force, vortex-shedding, VIV
Procedia PDF Downloads 3636287 Interplay of Imaginary, Symbolic and Real In Shakespeare's Hamlet, Disturbance of Nature
Authors: Mahnaz Poorshahidi
Abstract:
This article is a psychological reading of Shakespeare’s Hamlet applying Lacan’s ideas to work with a new look. Lacan entitled Hamlet ‘tragedy of desire’. He believes that Hamlet is caught up in the desire of his mother. So he is the universal symbol of all human beings, regardless of their sex, who desire their mother, but based on the rules of Nature and Father, this unity is impossible. Hamlet hesitates in fulfilling the task of revenge and the text says nothing about the reasons and motives behind it. However, this essay tries to answer the question and justify Hamlet’s hesitation. There is one question for the readers, which is why Hamlet appears to delay in killing his uncle, despite the fact that this is precisely what he seems to want to do. In 1958-59 Lacan delivered a series of lectures on Hamlet entitled ‘Desire and Its Interpretations’ and called it ‘tragedy of desire’. However, this article will have a new representation of Hamlet’s decision not to take revenge. The research demonstrates that Hamlet has passed through imaginary, symbolic and real stages, which are the natural process of life. Eliminating father means disturbing this natural process. This essay is going to conclude that killing Claudius can break the natural order of life. On the other hand, Claudius has also disturbed nature and is regretful about his deed. Hamlet’s ever-present speech ‘To be or not to be’ reflects his mental turmoil and disturbance of the natural life cycle: Nature.Keywords: desire, father figure, lacan, nature
Procedia PDF Downloads 2216286 Surface Sunctionalization Strategies for the Design of Thermoplastic Microfluidic Devices for New Analytical Diagnostics
Authors: Camille Perréard, Yoann Ladner, Fanny D'Orlyé, Stéphanie Descroix, Vélan Taniga, Anne Varenne, Cédric Guyon, Michael. Tatoulian, Frédéric Kanoufi, Cyrine Slim, Sophie Griveau, Fethi Bedioui
Abstract:
The development of micro total analysis systems is of major interest for contaminant and biomarker analysis. As a lab-on-chip integrates all steps of an analysis procedure in a single device, analysis can be performed in an automated format with reduced time and cost, while maintaining performances comparable to those of conventional chromatographic systems. Moreover, these miniaturized systems are either compatible with field work or glovebox manipulations. This work is aimed at developing an analytical microsystem for trace and ultra trace quantitation in complex matrices. The strategy consists in the integration of a sample pretreatment step within the lab-on-chip by a confinement zone where selective ligands are immobilized for target extraction and preconcentration. Aptamers were chosen as selective ligands, because of their high affinity for all types of targets (from small ions to viruses and cells) and their ease of synthesis and functionalization. This integrated target extraction and concentration step will be followed in the microdevice by an electrokinetic separation step and an on-line detection. Polymers consisting of cyclic olefin copolymer (COC) or fluoropolymer (Dyneon THV) were selected as they are easy to mold, transparent in UV-visible and have high resistance towards solvents and extreme pH conditions. However, because of their low chemical reactivity, surface treatments are necessary. For the design of this miniaturized diagnostics, we aimed at modifying the microfluidic system at two scales : (1) on the entire surface of the microsystem to control the surface hydrophobicity (so as to avoid any sample wall adsorption) and the fluid flows during electrokinetic separation, or (2) locally so as to immobilize selective ligands (aptamers) on restricted areas for target extraction and preconcentration. We developed different novel strategies for the surface functionalization of COC and Dyneon, based on plasma, chemical and /or electrochemical approaches. In a first approach, a plasma-induced immobilization of brominated derivatives was performed on the entire surface. Further substitution of the bromine by an azide functional group led to covalent immobilization of ligands through “click” chemistry reaction between azides and terminal alkynes. COC and Dyneon materials were characterized at each step of the surface functionalization procedure by various complementary techniques to evaluate the quality and homogeneity of the functionalization (contact angle, XPS, ATR). With the objective of local (micrometric scale) aptamer immobilization, we developed an original electrochemical strategy on engraved Dyneon THV microchannel. Through local electrochemical carbonization followed by adsorption of azide-bearing diazonium moieties and covalent linkage of alkyne-bearing aptamers through click chemistry reaction, typical dimensions of immobilization zones reached the 50 µm range. Other functionalization strategies, such as sol-gel encapsulation of aptamers, are currently investigated and may also be suitable for the development of the analytical microdevice. The development of these functionalization strategies is the first crucial step in the design of the entire microdevice. These strategies allow the grafting of a large number of molecules for the development of new analytical tools in various domains like environment or healthcare.Keywords: alkyne-azide click chemistry (CuAAC), electrochemical modification, microsystem, plasma bromination, surface functionalization, thermoplastic polymers
Procedia PDF Downloads 4356285 Occupational Health and Safety Implications of Flower Farming on the Local Communities in Central Uganda
Authors: Charles Owenda Omulo
Abstract:
This study examines Occupational Health and Safety implications in flower farms in Central Uganda. An exploratory sequential mixed method design and methodology was employed, with multiple data collection methods, including interviews, focus group discussions, and surveys. The findings show that occupational health and safety issues remain a major problem in flower farms. While the majority of workers agreed that the farms provided them with protective equipment, the data collected from the workers point to either the improper use or ineffectiveness of this equipment. A number of workers reported skin irritations, sore and painful eyes, stiff necks, back pains, and occasional headaches that were presumably argued to have arisen from their work environment. The study also found that farms have been adjusting in an attempt to correct some of these anomalies. These included the use of biological approaches to control pests and diseases and restricting the use of some chemical formulations that are deemed to be harmful to applicators and the environment. Alongside these efforts, the study recommends increased vigilance by the flower farm owners in the provision of personal protective equipment to workers.Keywords: flower farms, personal protective equipment, agrochemicals, rural communities, occupational health and safety
Procedia PDF Downloads 496284 Reciprocity and Empathy in Motivating Altruism among Sixth Grade Students
Authors: Rylle Evan Gabriel Zamora, Micah Dennise Malia, Abygail Deniese Villabona
Abstract:
The primary motivators of altruism are usually viewed as mutually exclusive. In this study, we wanted to know if the two primary motivators, reciprocity and empathy, can work together in motivating altruism. Therefore, we wanted to find out if there is a significant interaction of effects between reciprocity and empathy. To show how this may occur, we devised the combined altruism model, which is based on Batson’s empathy altruism hypothesis. A sample of 120, 6th-grade students were randomly selected and then randomly assigned to four treatment groups. A 2x2 between subjects’ design was used, which had empathy and reciprocity as independent variables, and altruism as the dependent variable. The study made use of materials that were effort based, where subjects were required to complete a task or a puzzle to help a person in a given scenario, two videos, one to prime empathy were also used. This along with Witt & Boleman’s adapted Self-Reported Altruism Scale was used to determine an individual’s altruism. It was found that both variables were significant in motivating altruism, with empathy being the greater of the two. However, there was no significant interaction of effects between the two variables. To explain why this occurred, we turned to the combined altruism model, where it was found that when empathically primed, we tend to not think of ourselves when helping others. Future studies could focus on other variables, especially age which is said to be one of the greatest factors that influenced the results of the experiment.Keywords: reciprocity, empathy, altruism, experimental psychology, social psychology
Procedia PDF Downloads 2416283 Unmasking Theatrical Language: Exploring Ideological Connections in American Theater
Authors: Gizem Barreto Martins
Abstract:
This paper explores the subversive potential inherent in the theatrical language employed within Arthur Miller's The Crucible. The research argues that this play intricately weaves ideological connections with its audience and the historical epoch it represents, effectively serving as a channel for ideological and cultural interaction potentially exerting subversive influences on social and political realms. Using a historical-materialist methodology that situates the play within its historical and political context, all while examining its connections with theater and literary theories, the paper raises a fundamental query: How does this dramatic work embody subversion, presenting a style unburdened by the performative conventions of daily life and prevailing codes and systems of representation? In response to this inquiry, the study asserts that theatrical language has the capacity to function as a subversive catalyst against prevailing ideologies, actively contributing to the process of social transformation. To substantiate this claim, the research conducts a detailed analysis of the selected play, employing the semiotic framework pioneered by Gilles Deleuze and Felix Guattari.Keywords: arthur miller, The crucible, gilles deleuze, felix guattari, theater and literary theories
Procedia PDF Downloads 526282 Assessment of Material Type, Diameter, Orientation and Closeness of Fibers in Vulcanized Reinforced Rubbers
Authors: Ali Osman Güney, Bahattin Kanber
Abstract:
In this work, the effect of material type, diameter, orientation and closeness of fibers on the general performance of reinforced vulcanized rubbers are investigated using finite element method with experimental verification. Various fiber materials such as hemp, nylon, polyester are used for different fiber diameters, orientations and closeness. 3D finite element models are developed by considering bonded contact elements between fiber and rubber sheet interfaces. The fibers are assumed as linear elastic, while vulcanized rubber is considered as hyper-elastic. After an experimental verification of finite element results, the developed models are analyzed under prescribed displacement that causes tension. The normal stresses in fibers and shear stresses between fibers and rubber sheet are investigated in all models. Large deformation of reinforced rubber sheet also represented with various fiber conditions under incremental loading. A general assessment is achieved about best fiber properties of reinforced rubber sheets for tension-load conditions.Keywords: reinforced vulcanized rubbers, fiber properties, out of plane loading, finite element method
Procedia PDF Downloads 3356281 Study of the Green Composite Jute/Epoxy
Authors: A. Mir, C. Aribi, B. Bezzazi
Abstract:
Work presented is interested in the characterization of the quasistatic mechanical properties and in fatigue of a composite laminated in jute/epoxy. The natural fibers offer promising prospects thanks to their interesting specific properties, because of their low density, but also with their bio deterioration. Several scientific studies highlighted the good mechanical resistance of the vegetable fiber composites reinforced, even after several recycling. Because of the environmental standards which become increasingly severe, one attends the emergence of eco-materials at the base of natural fibers such as flax, bamboo, hemp, sisal, jute. The fatigue tests on elementary vegetable fibers show an increase of about 60% of the rigidity of elementary fibers of hemp subjected to cyclic loading. In this study, the test-tubes manufactured by the method infusion have sequences of stacking of 0/90° and ± 45° for the shearing and tensile tests. The quasistatic tests reveal a variability of the mechanical properties of about 8%. The tensile fatigue tests were carried out for levels of constraints equivalent to half of the ultimate values of the composite. Once the fatigue tests carried out for well-defined values of cycles, a series of static tests of traction type highlights the influence of the number of cycles on the quasi static mechanical behavior of the laminate jute/epoxy.Keywords: jute, epoxy resin, mechanical, static, dynamic behavior
Procedia PDF Downloads 2396280 Design and Implementation of an Efficient Solar-Powered Pumping System
Authors: Mennatallah M. Fouad, Omar Hussein, Lamia A. Shihata
Abstract:
The main problem in many rural areas is the absence of electricity and limited access to water. The novelty of this work lies in implementing a small-scale experimental setup for a solar-powered water pumping system with a battery back-up system. Cooling and cleaning of the PV panel are implemented to enhance its overall efficiency and output. Moreover, a simulation for a large scale solar-powered pumping system is performed using PVSyst software. Results of the experimental setup show that the PV system with a battery backup proved to be a feasible and viable system to operate the water pumping system. Excess water from the pumping system is used to cool and clean the PV panel and achieved an average percentage increase in the PV output by 21.8%. Simulation results have shown that the system provides adequate output to power the solar-powered system and saves 0.3 tons of CO₂ compared to conventional fossil fuels. It is recommended for hot countries to adopt this system, which would help in decreasing the dependence on the depleting fossil fuels, provide access to electricity to areas where there is no electricity supply and also provide a source of water for crop growth as well as decrease the carbon emissions.Keywords: efficient solar pumping, PV cleaning, PV cooling, PV-operated water pump
Procedia PDF Downloads 1266279 Power Quality Improvement Using UPQC Integrated with Distributed Generation Network
Authors: B. Gopal, Pannala Krishna Murthy, G. N. Sreenivas
Abstract:
The increasing demand of electric power is giving an emphasis on the need for the maximum utilization of renewable energy sources. On the other hand maintaining power quality to satisfaction of utility is an essential requirement. In this paper the design aspects of a Unified Power Quality Conditioner integrated with photovoltaic system in a distributed generation is presented. The proposed system consist of series inverter, shunt inverter are connected back to back on the dc side and share a common dc-link capacitor with Distributed Generation through a boost converter. The primary task of UPQC is to minimize grid voltage and load current disturbances along with reactive and harmonic power compensation. In addition to primary tasks of UPQC, other functionalities such as compensation of voltage interruption and active power transfer to the load and grid in both islanding and interconnected mode have been addressed. The simulation model is design in MATLAB/ Simulation environment and the results are in good agreement with the published work.Keywords: distributed generation (DG), interconnected mode, islanding mode, maximum power point tracking (mppt), power quality (PQ), unified power quality conditioner (UPQC), photovoltaic array (PV)
Procedia PDF Downloads 4976278 Understanding Public Opinion about Environment Issue in Kedah (Malaysia)
Authors: Roozbeh Kardooni, Ahmad Hossein Meidari, Sumiani Binti Yusoff, Fatimah Binti Kari,
Abstract:
The public opinion on environmental issue was analyzed by means of a survey implemented in Kedah located in the northwestern part of Peninsular Malaysia (West Malaysia). This work explores public opinions regarding environmental issue such as climate change, green technology and renewable energy in Kedah. Probability sampling and a stratified technique were used to conduct a survey with subjects aged 20 years and over with higher education qualifications. The results shows that the level of concern regarding climate change in Kedah is high and majority of Kedah citizens are concerned about climate change and have heard about green technology. However, only 40% people in this city have used green products. The findings of this study also show that percent use of green products is highest among those who are familiar with such products. It is apparent from study finding that economic barriers and non-economic barriers both play a role in impeding the development of renewable energy policies in Kedah. This finding can be explained by the high price of renewable energy products, lack of knowledge about government policies, and ineffective programs and initiatives.Keywords: public opinion, climate change, green technology, Kedah
Procedia PDF Downloads 3756277 Analysis of the Extreme Hydrometeorological Events in the Theorical Hydraulic Potential and Streamflow Forecast
Authors: Sara Patricia Ibarra-Zavaleta, Rabindranarth Romero-Lopez, Rosario Langrave, Annie Poulin, Gerald Corzo, Mathias Glaus, Ricardo Vega-Azamar, Norma Angelica Oropeza
Abstract:
The progressive change in climatic conditions worldwide has increased frequency and severity of extreme hydrometeorological events (EHE). Mexico is an example; this has been affected by the presence of EHE leaving economic, social and environmental losses. The objective of this research was to apply a Canadian distributed hydrological model (DHM) to tropical conditions and to evaluate its capacity to predict flows in a basin in the central Gulf of Mexico. In addition, the DHM (once calibrated and validated) was used to calculate the theoretical hydraulic power and the performance to predict streamflow before the presence of an EHE. The results of the DHM show that the goodness of fit indicators between the observed and simulated flows in the calibration process (NSE=0.83, RSR=0.021 and BIAS=-4.3) and validation: temporal was assessed at two points: point one (NSE=0.78, RSR=0.113 and BIAS=0.054) and point two (NSE=0.825, RSR=0.103 and BIAS=0.063) are satisfactory. The DHM showed its applicability in tropical environments and its ability to characterize the rainfall-runoff relationship in the study area. This work can serve as a tool for identifying vulnerabilities before floods and for the rational and sustainable management of water resources.Keywords: HYDROTEL, hydraulic power, extreme hydrometeorological events, streamflow
Procedia PDF Downloads 3326276 Giftedness Cloud Model: A Psychological and Ecological Vision of Giftedness Concept
Authors: Rimeyah H. S. Almutairi, Alaa Eldin A. Ayoub
Abstract:
The aim of this study was to identify empirical and theoretical studies that explored giftedness theories and identification. In order to assess and synthesize the mechanisms, outcomes, and impacts of gifted identification models. Thus, we sought to provide an evidence-informed answer to how does current giftedness theories work and effectiveness. In order to develop a model that incorporates the advantages of existing models and avoids their disadvantages as much as possible. We conducted a systematic literature review (SLR). The disciplined analysis resulted in a final sample consisting of 30 appropriate searches. The results indicated that: (a) there is no uniform and consistent definition of Giftedness; (b) researchers are using several non-consistent criteria to detect gifted, and (d) The detection of talent is largely limited to early ages, and there is obvious neglect of adults. This study contributes to the development of Giftedness Cloud Model (GCM) which defined as a model that attempts to interpretation giftedness within an interactive psychological and ecological framework. GCM aims to help a talented to reach giftedness core and manifestation talent in creative productivity or invention. Besides that, GCM suggests classifying giftedness into four levels of mastery, excellence, creative productivity, and manifestation. In addition, GCM presents an idea to distinguish between talent and giftedness.Keywords: giftedness cloud model, talent, systematic literature review, giftedness concept
Procedia PDF Downloads 1596275 Fuzzy Adaptive Control of an Intelligent Hybrid HPS (Pvwindbat), Grid Power System Applied to a Dwelling
Authors: A. Derrouazin, N. Mekkakia-M, R. Taleb, M. Helaimi, A. Benbouali
Abstract:
Nowadays the use of different sources of renewable energy for the production of electricity is the concern of everyone, as, even impersonal domestic use of the electricity in isolated sites or in town. As the conventional sources of energy are shrinking, a need has arisen to look for alternative sources of energy with more emphasis on its optimal use. This paper presents design of a sustainable Hybrid Power System (PV-Wind-Storage) assisted by grid as supplementary sources applied to case study residential house, to meet its entire energy demand. A Fuzzy control system model has been developed to optimize and control flow of power from these sources. This energy requirement is mainly fulfilled from PV and Wind energy stored in batteries module for critical load of a residential house and supplemented by grid for base and peak load. The system has been developed for maximum daily households load energy of 3kWh and can be scaled to any higher value as per requirement of individual /community house ranging from 3kWh/day to 10kWh/day, as per the requirement. The simulation work, using intelligent energy management, has resulted in an optimal yield leading to average reduction in cost of electricity by 50% per day.Keywords: photovoltaic (PV), wind turbine, battery, microcontroller, fuzzy control (FC), Matlab
Procedia PDF Downloads 6416274 Nietzsche and Shakti: An Intercultural Analysis of Nietzsche's Experiment with the Eternal Feminine
Authors: Shruti Jain
Abstract:
During its independence struggle in the early 20th century, India witnessed trends of politicisation of various spiritual paths, one of them being that of Shaktism. Interestingly, Nietzsche’s teachings were being interpreted as being essentially the worship of Shakti. The present paper aims at investigating this claim and hence undertakes an intercultural archaeological excavation in the realm of the Goddess archetypes that Nietzsche’s work invokes. Ariadne is placed next to Radha, Baubo to Lajja Gauri, Medusa to Chhinnamasta, Hecate to Kali and Dhumavati and Athena to Sarawati. Indeed, the Eternal Feminine plays a vital role in Nietzsche’s writings. One might recall that Nietzsche even declared himself to be the first Psychologist of the Eternal Feminine. The present paper aims to illustrate how, the matter of the Eternal Feminine, like all other matters, is subjected to Nietzsche’s basic creative principle of transvaluation of values and new meaning making. In order to achieve this, Nietzsche applies what Heidegger calls a 'cross-wise striking-through' technique in his analysis of what can be termed as his engagement with Shaktism. Hence, not only is the mystical ascent and descent of the creative energy (Kundalini Shakti) dealt with under erasure in Thus Spake Zarathustra, but coincidentally also the Three Metamorphoses emerge as an instance of such an erasure, making the Devi invisible and yet not so invisible for an Indian reader.Keywords: eternal feminine, Nietzsche and India, Shaktism, transvaluation of values
Procedia PDF Downloads 1516273 An Assessment of the Impact of Safe Motherhood Initiative on Maternal Health of Women in Gumel Local Government Area of Jigawa State, Nigeria
Authors: Ahmed Mudi, Bala Zakar
Abstract:
The paper assesses the impact of safe motherhood initiative on maternal health of women in Gumel Local Government Area of Jigawa State. The work will specifically concentrate on the background on safe motherhood scheme and maternal health of women. The objective of this paper is to assess the level of safe motherhood scheme in Gumel local government area, to find out the level of maternal health in Gumel local government as well as to determine the impact of safe motherhood scheme on maternal health on women in Gumel Local Government Area Jigawa State. Various literature on the topic are reviewed, the paper adopts survey design and use questionnaire to collect data from the respondent. The study comprises 350 women selected from six rural communities in Gumel using random sampling techniques, and the data was analysed by simple frequency and percentage. The research concluded that safe motherhood initiative has a significant impact on the maternal health of women in Gumel Local Government Area of Jigawa State. Finally, suitable recommendations were given on how to improve the scheme to ensure better maternal health in the region.Keywords: action, assessment, maternal health, safe motherhood, surgery
Procedia PDF Downloads 2566272 Change in Food Choice Behavior: Trend and Challenges
Authors: Gargi S. Kumar, Mrinmoyi Kulkarni
Abstract:
Food choice behavior is complex and determined by biological, psychological, socio-cultural, and economic factors. The past two decades, have seen dramatic changes in food consumption patterns among urban Indian consumers. The objective of the current study was to evaluate perceptions about changes with respect to food choice behavior. Ten participants [urban men and women] ranging in age from 40 to 65 were selected and in-depth interviews were conducted with a set of open ended questions. The recorded interviews were transcribed and thematically analyzed using inductive, open and axial coding. The results identified themes that act as drivers and consequences of change in food choice behavior. Drivers such as globalization [sub themes of urbanization, education, income, and work environment], media and advertising, changing gender roles, women in the workforce, and change in family structure have influenced food choice, both at an individual and national level. The consequences of changes in food choice were health implications, processed food consumption, food decisions driven by children and eating out among others. The study reveals that, over time, food choices change and evolve. However it is interesting to note how market forces and culture interact to influence individual behavior and the overall food environment which subsequently affects food choice and the health of the people.Keywords: change, consequences, drivers, food choice, globalization
Procedia PDF Downloads 2186271 Celebrity Endorsement: How It Works When a Celebrity Fits the Brand and Advertisement
Authors: Göksel Şimşek
Abstract:
Celebrities are admired, appreciated and imitated all over the world. As a natural result of this, today many brands choose to work with celebrities for their advertisements. It can be said that the more the brands include celebrities in their marketing communication strategies, the tougher the competition in this field becomes and they allocate a large portion of their marketing budget to this. Brands invest in celebrities who will represent them in order to build the image they want to create. This study aimed to bring under spotlight the perceptions of Turkish customers regarding the use of celebrities in advertisements and marketing communication and try to understand their possible effects on subsequent purchasing decisions. In addition, consumers’ reactions and perceptions were investigated in the context of the product-celebrity match, to what extent the celebrity conforms to the concept of the advertisement and the celebrity-target audience match. In order to achieve this purpose, a quantitative research was conducted as a case study concerning Mavi Jeans (textile company). Information was obtained through survey. The results from this case study are supported by relevant theories concerning the main subject. The most valuable result would be that instead of creating an advertisement around a celebrity in demand at the time, using a celebrity that fits the concept of the advertisement and feeds the concept rather than replaces it, that is celebrity endorsement, will lead to more striking and positive results.Keywords: celebrity endorsement, product-celebrity match, advertising, social sciences
Procedia PDF Downloads 1956270 Solubility of Water in CO2 Mixtures at Pipeline Operation Conditions
Authors: Mohammad Ahmad, Sander Gersen, Erwin Wilbers
Abstract:
Carbon capture, transport and underground storage have become a major solution to reduce CO2 emissions from power plants and other large CO2 sources. A big part of this captured CO2 stream is transported at high pressure dense phase conditions and stored in offshore underground depleted oil and gas fields. CO2 is also transported in offshore pipelines to be used for enhanced oil and gas recovery. The captured CO2 stream with impurities may contain water that causes severe corrosion problems, flow assurance failure and might damage valves and instrumentations. Thus, free water formation should be strictly prevented. The purpose of this work is to study the solubility of water in pure CO2 and in CO2 mixtures under real pipeline pressure (90-150 bar) and temperature operation conditions (5-35°C). A set up was constructed to generate experimental data. The results show the solubility of water in CO2 mixtures increasing with the increase of the temperature or/and with the increase in pressure. A drop in water solubility in CO2 is observed in the presence of impurities. The data generated were then used to assess the capabilities of two mixture models: the GERG-2008 model and the EOS-CG model. By generating the solubility data, this study contributes to determine the maximum allowable water content in CO2 pipelines.Keywords: carbon capture and storage, water solubility, equation of states, fluids engineering
Procedia PDF Downloads 2876269 Optical Characterization of Erbium-Mixed Silicon Nanocrystals
Authors: Khamael M. Abualnaja, Lidija Šiller, Ben R. Horrocks
Abstract:
The structural characterization of silicon nano crystals (SiNCs) have been carried out using transmission electron microscope (TEM) and atomic force microscopy (AFM). SiNCs are crystalline with an average diameter of 65 nm. Erbium trichloride was added to silicon nano crystals using a simple chemical procedure. Erbium is useful in this context because it has a narrow emission band at ⋍1536 nm which corresponds to a standard optical telecommunication wavelength. The optical properties of SiNCs and erbium-mixed SiNCs samples have been characterized using UV-vis spectroscopy, confocal Raman spectroscopy and photoluminescence spectroscopy (PL). SiNCs and erbium-mixed SiNCs samples exhibit an orange PL emission peak at around 595 nm that arise from radiative recombination of Si. Erbium-mixed SiNCs also shows a weak PL emission peak at ⋍1536 nm that attributed to the intra-4f transition in erbium ions. The intensity of the PL peak of Si in erbium-mixed SiNCs is increased in the intensity up to ×3 as compared to pure SiNCs. It was observed that intensity of 1536 nm peak decreased dramatically in the presence of silicon nano crystals and the PL emission peak of silicon nano crystals is increased. Therefore, the resulted data present that the energy transfer from erbium ions to SiNCs due to the chemical mixing method which used in this work.Keywords: Silicon Nanocrystals (SiNCs), Erbium Ion, photoluminescence, energy transfer
Procedia PDF Downloads 3656268 Droplet Impact on a High Frequency Vibrating Surface
Authors: Maryam Ebrahimiazar, Parsia Mohammadshahi, Amirreza Amighi, Nasser Ashgriz
Abstract:
Ultrasonic atomization is used to generate micron size aerosols. In this work, the aerosol formation by the atomization of a parent droplet dripping from a capillary needle onto the surface of a Teflon coated piezoelectric vibrating at 2.5 MHz is studied, and different steps of atomization are categorized. After the droplet impacts on the piezoelectric, surface acoustic streaming deforms the droplet into a fountain shape. This fountain soon collapses and forms a liquid layer. The breakup of the liquid layer results in the generation of both large ( 100 microns) and small drops (few microns). Next, the residual drops from the liquid layer start to be atomized to generate few micron size droplets. The high velocity and explosive aerosol formation in this step are better explained in terms of cavitation theory. However, the combination of both capillary waves and cavitation theory seem to be responsible for few-micron droplet generation. The current study focuses on both qualitative and quantitative aspects of fountain formation for both ethyl-alcohol and water. Even though the general steps of atomization are the same for both liquids, the quantitative results indicate that some noticeable differences lie between them.Keywords: droplet breakup, ultrasonic atomization, acoustic streaming, droplet oscillation
Procedia PDF Downloads 1686267 The Characteristics of the Graduates Based on Thailand Qualification Framework (TQF) of the Faculty of Industrial Technology, Suan Sunandha Rajabhat University
Authors: Apinya Mungaomklang, Natakamol Lookkham
Abstract:
The purpose of this research is to study the characteristics of the graduates based on Thailand Qualification Framework (TQF) of the Faculty of Industrial Technology, Suan Sunandha Rajabhat University. The population of the research was employers/entrepreneurs/supervisors of students who were doing Professional Experiences course in their respective organizations during semester 1/2012. Data were collected during the month of September 2012 from the total number of 100 people. The tool used in this research was a questionnaire developed by the research team. Data were analyzed using percentage, mean and standard deviation using a computer program. The results showed that most of the surveyed organizations were private companies. The program with most students doing Professional Experiences course was Safety Technology and Occupational Health. The nature of work that most students did was associated with the document. Employers/ entrepreneurs/employers’ opinions on the characteristics of the graduates based on TQF received high scores. Cognitive skills received the highest score, followed by interpersonal relationships and responsibilities, ethics and moral, numerical analysis skills, communication and information technology skills, and knowledge, respectively.Keywords: graduates characteristics, Thailand Qualification Framework, employers, entrepreneurs
Procedia PDF Downloads 3106266 Nighttime Dehaze - Enhancement
Authors: Harshan Baskar, Anirudh S. Chakravarthy, Prateek Garg, Divyam Goel, Abhijith S. Raj, Kshitij Kumar, Lakshya, Ravichandra Parvatham, V. Sushant, Bijay Kumar Rout
Abstract:
In this paper, we introduce a new computer vision task called nighttime dehaze-enhancement. This task aims to jointly perform dehazing and lightness enhancement. Our task fundamentally differs from nighttime dehazing – our goal is to jointly dehaze and enhance scenes, while nighttime dehazing aims to dehaze scenes under a nighttime setting. In order to facilitate further research on this task, we release a new benchmark dataset called Reside-β Night dataset, consisting of 4122 nighttime hazed images from 2061 scenes and 2061 ground truth images. Moreover, we also propose a new network called NDENet (Nighttime Dehaze-Enhancement Network), which jointly performs dehazing and low-light enhancement in an end-to-end manner. We evaluate our method on the proposed benchmark and achieve SSIM of 0.8962 and PSNR of 26.25. We also compare our network with other baseline networks on our benchmark to demonstrate the effectiveness of our approach. We believe that nighttime dehaze-enhancement is an essential task, particularly for autonomous navigation applications, and we hope that our work will open up new frontiers in research. Our dataset and code will be made publicly available upon acceptance of our paper.Keywords: dehazing, image enhancement, nighttime, computer vision
Procedia PDF Downloads 1396265 The Long-Term Leaching Behaviour of 137Cs, 60Co and 152Eu Radionuclides Incorporated in Mortar Matrices Made from Natural Aggregates and Recycled Aggregates
Authors: R. Deju, M. Mincu, D. Gurau
Abstract:
During the interim storage or final disposal of low level waste, migration/diffusion of radionuclides can occur when the waste comes in contact with water. The long-term leaching behaviour into surrounding fluid (demineralized water) of 137Cs, 60Co and 152Eu radionuclides, artificially incorporated in mortar matrices made from natural aggregates (river sand) and recycled radioactive concrete was studied. Results presented in this work are obtained in two years of mortar testing and will be used for the safety increasing in the storage of low level radioactive waste. The study involved the influence of curing time, type and size distribution of the aggregates on leaching behaviour. The mortar samples were immersed in distilled water for 30 days. The leached activity of the mortar samples was measured on samples from the immersing water and analyzed through a gamma-ray spectrometry method using an HPGe detector with a GESPECOR code for efficiency evaluation. The long-term leaching behaviour of the radionuclides was evaluated from the leaching data calculating the apparent diffusion coefficient.Keywords: gamma spectrometry, leaching behavior, reuse and recycling of radioactive concrete, waste management
Procedia PDF Downloads 2346264 The Concepts of Urban Sustainable Development and Smart Cities: In the Understanding of Academia and the European Union
Authors: Wolfgang Haupt
Abstract:
When considering the future city one repeatedly comes across two sometimes sparsely differentiated terms: Sustainable and smart. ‘A European Strategy for Smart, Sustainable, and Inclusive Growth’, this is how the European Commission named its current growth strategy. Thus, Europe should become smarter and more sustainable. Both, the smart and the sustainable city represent a positive vision of urban development as well as a subject area for contemporary and future urban policies. However, more clarity on what is actually behind these terminologies is required. The paper analyses how the terms are defined academically and how this academic understanding is represented in the funding mechanisms of European urban policies. The theoretical framework is mainly based on sources such as journal articles and policy reports. It became clear that despite some similarities, such as the broad field of work or the tendency to operationalize the terms by defining sub-categories, both ideas are distinctly different in terms of the development history, the main driving forces behind and the theoretical scope. Moreover, the significantly more comprehensively defined term sustainability has found its way into the centre of European regional funding policies. On the contrary, the smart city vision still lacks terminological and content-related clarity and as a consequence, the corresponding European funding landscape is more small-scaled and less customized.Keywords: European spatial policy, European union, smart city, urban sustainable development
Procedia PDF Downloads 3566263 Abdominal Organ Segmentation in CT Images Based On Watershed Transform and Mosaic Image
Authors: Belgherbi Aicha, Hadjidj Ismahen, Bessaid Abdelhafid
Abstract:
Accurate Liver, spleen and kidneys segmentation in abdominal CT images is one of the most important steps for computer aided abdominal organs pathology diagnosis. In this paper, we have proposed a new semi-automatic algorithm for Liver, spleen and kidneys area extraction in abdominal CT images. Our proposed method is based on hierarchical segmentation and watershed algorithm. In our approach, a powerful technique has been designed to suppress over-segmentation based on mosaic image and on the computation of the watershed transform. The algorithm is currency in two parts. In the first, we seek to improve the quality of the gradient-mosaic image. In this step, we propose a method for improving the gradient-mosaic image by applying the anisotropic diffusion filter followed by the morphological filters. Thereafter we proceed to the hierarchical segmentation of the liver, spleen and kidney. To validate the segmentation technique proposed, we have tested it on several images. Our segmentation approach is evaluated by comparing our results with the manual segmentation performed by an expert. The experimental results are described in the last part of this work.Keywords: anisotropic diffusion filter, CT images, morphological filter, mosaic image, multi-abdominal organ segmentation, mosaic image, the watershed algorithm
Procedia PDF Downloads 4846262 Mechanical Testing on Bioplastics Obtained from Banana and Potato Peels in the City of Bogotá, Colombia
Authors: Juan Eduardo Rolon Rios, Fredy Alejandro Orjuela, Alexander Garcia Mariaca
Abstract:
For banana and potato wastes, their peels are processed in order to make animal food with the condition that those wastes must not have started the decomposition process. One alternative to taking advantage of those wastes is to obtain a bioplastic based on starch from banana and potato shells. These products are 100% biodegradables, and researchers have been studying them for different applications, helping in the reduction of organic wastes and ordinary plastic wastes. Without petroleum affecting the prices of bioplastics, bioplastics market has a growing tendency and it is seen that it can keep this tendency in the medium term up to 350%. In this work, it will be shown the results for elasticity module and percent elongation for bioplastics obtained from a mixture of starch of bananas and potatoes peels, with glycerol as plasticizer. The experimental variables were the plasticizer percentage and the mixture between banana starch and potato starch. The results show that the bioplastics obtained can be used in different applications such as plastic bags or sorbets, verifying their admissible degradation percentages for each one of these applications. The results also show that they agree with the data found in the literature due to the fact that mixtures with a major amount of potato starch had the best mechanical properties because of the potato starch characteristics.Keywords: bioplastics, fruit waste, mechanical testing, mechanical properties
Procedia PDF Downloads 2846261 Randomly Casted Single-Wall Carbon Nanotubes Films for High Performance Hybrid Photovoltaic Devices
Authors: My Ali El Khakani
Abstract:
Single-wall Carbon nanotubes (SWCNTs) possess an unprecedented combination of unique properties that make them highly promising for suitable for a new generation of photovoltaic (PV) devices. Prior to discussing the integration of SWCNTs films into effective PV devices, we will briefly highlight our work on the synthesis of SWCNTs by means of the KrF pulsed laser deposition technique, their purification and transfer onto n-silicon substrates to form p-n junctions. Some of the structural and optoelectronic properties of SWCNTs relevant to PV applications will be emphasized. By varying the SWCNTs film density (µg/cm2), we were able to point out the existence of an optimum value that yields the highest photoconversion efficiency (PCE) of ~10%. Further control of the doping of the p-SWCNTs films, through their exposure to nitric acid vapors, along with the insertion of an optimized hole-extraction-layer in the p-SWCNTs/n-Si hybrid devices permitted to achieve a PCE value as high as 14.2%. Such a high PCE value demonstrates the full potential of these p-SWCNTs/n-Si devices for sunlight photoconversion. On the other hand, by examining both the optical transmission and electrical conductance of the SWCNTs’ films, we established a figure of merit (FOM) that was shown to correlate well with the PCE performance. Such a direct relationship between the FOM and the PCE can be used as a guide for further PCE enhancement of these novel p-SWCNTs/n-Si PV devices.Keywords: carbon nanotubes (CNTs), CNTs-silicon hybrid devices, photoconversion, photovoltaic devices, pulsed laser deposition
Procedia PDF Downloads 1096260 Electrocardiogram-Based Heartbeat Classification Using Convolutional Neural Networks
Authors: Jacqueline Rose T. Alipo-on, Francesca Isabelle F. Escobar, Myles Joshua T. Tan, Hezerul Abdul Karim, Nouar Al Dahoul
Abstract:
Electrocardiogram (ECG) signal analysis and processing are crucial in the diagnosis of cardiovascular diseases, which are considered one of the leading causes of mortality worldwide. However, the traditional rule-based analysis of large volumes of ECG data is time-consuming, labor-intensive, and prone to human errors. With the advancement of the programming paradigm, algorithms such as machine learning have been increasingly used to perform an analysis of ECG signals. In this paper, various deep learning algorithms were adapted to classify five classes of heartbeat types. The dataset used in this work is the synthetic MIT-BIH Arrhythmia dataset produced from generative adversarial networks (GANs). Various deep learning models such as ResNet-50 convolutional neural network (CNN), 1-D CNN, and long short-term memory (LSTM) were evaluated and compared. ResNet-50 was found to outperform other models in terms of recall and F1 score using a five-fold average score of 98.88% and 98.87%, respectively. 1-D CNN, on the other hand, was found to have the highest average precision of 98.93%.Keywords: heartbeat classification, convolutional neural network, electrocardiogram signals, generative adversarial networks, long short-term memory, ResNet-50
Procedia PDF Downloads 113