Search results for: rise of bubble

Authors: Amit Singla, Amit Chauhan

Abstract:

The non-circular journal bearings provide better thermal stability and lesser oil-film temperature rise as compared to circular journal bearings. Experimentation on simultaneous measurement of pressure and temperature of lubricated oil-film along the profile of the bearing will help the designer to design journal bearings. In this paper, pressure and temperature of oil-film along orthogonally displaced non-circular journal bearing have been measured on a designed journal bearing test rig. The orthogonal non-circular journal bearing has been fabricated by displacing two circular halves away from the centers in the orthogonal direction. The data acquisition for oil film pressure and temperature has been carried out at journal speed=3000 rpm and by increasing the static radial load from 500 N to 2000 N in steps of 500 N using three different grades of oil (ISOVG 32, 68, and 150) named as oil-1, oil-2, and oil-3 respectively. The results show that the oil-film pressure and temperature increases with increase in radial load and change of lubricating oil towards increasing viscosity. Further, two lobes in the pressure and temperature profiles have been obtained which accounts for better thermal stability as it reduces cavitation zone inside the bearing.

Keywords: cavitation, non-circular journal bearing, orthogonally displaced, thermal stability

Procedia PDF Downloads 336

Authors: Charizza D. Montarin, Daryl Jae S. Sigue, Gilford Estores

Abstract:

Philippines was moderately vulnerable to corrosion and to prevent this problem, surface coating should be applied. The main objective of this research was to develop and optimize a bio-based mixture of Pili Resin and Lime as Coating Materials. There are three (3) factors to be considered in choosing the best coating material such as chemical adhesion, friction, and the bearing/shear against the steel bar-concrete interface. Fortunately, both proportions of the Bio-based coating materials (50:50 and 65:35) do not have red rust formation complying with ASTM B117 but failed in terms of ASTM D 3359. Splitting failures of concrete were observed in the Unconfined Reinforced Concrete Samples. All of the steel bars (uncoated and coated) surpassed the Minimum Bond strength (NSCP 2015) about 203% to 285%. The experiments were about 1% to 3% of the results from the ANSYS Simulations with and without Salt Spray Test. Using the bio-based and epoxy coatings, normal splitting strengths were declined. However, there has no significant difference between the results. Thus, the bio-based coating materials can be used as an alternative for the epoxy coating materials and it was highly recommended for Low – Rise Building only.

Keywords: Canarium luzonicum, calcium oxide, corrosion, finite element simulations

Procedia PDF Downloads 306

Authors: Arash Ghahraman, Gyula Bene

Abstract:

The object of this study is to investigate the effect of viscosity on the propagation of free-surface waves in an incompressible viscous fluid layer of arbitrary depth. While we provide a more detailed study of properties of linear surface waves, the description of fully nonlinear waves in terms of KdV-like (Korteweg-de Vries) equations is discussed. In the linear case, we find that in shallow enough fluids, no surface waves can propagate. Even in any thicker fluid layers, propagation of very short and very long waves is forbidden. When wave propagation is possible, only a single propagating mode exists for any given horizontal wave number. The numerical results show that there can be two types of non-propagating modes. One type is always present, and there exist still infinitely many of such modes at the same parameters. In contrast, there can be zero, one or two modes belonging to the other type. Another significant feature is that KdV-like equations. They describe propagating nonlinear viscous surface waves. Since viscosity gives rise to a new wavenumber that cannot be small at the same time as the original one, these equations may not exist. Nonetheless, we propose a reasonable nonlinear description in terms of 1+1 variate functions that make possible successive approximations.

Keywords: free surface wave, water waves, KdV equation, viscosity

Procedia PDF Downloads 142

Authors: Deretha Bester

Abstract:

This research employs a theoretical framework to investigate the interplay between factors that lead from predatory governance and predatory rule to military coups, utilizing the frustration-aggression theory as its guiding lens. It adopts a case-oriented approach and employs thematic analysis to examine the socio-economic, governance, and political environment that precipitated the August 2020 Malian military coup. Presenting seven key themes, it reveals how predatory rule and its manifestation in the Malian context was a critical factor in paving the way for the military coup. The study provides critical reflections into the historical, regional, and political dynamics reshaping Africa’s changing political landscape. It presents a conceptual model to comprehend how predatory governance fosters conditions favorable for military coups. Insights from the Malian case study offer valuable perspectives for analyzing events in comparable contexts. This understanding is crucial for grasping the precursors and impact of predatory rule and popular frustrations in contexts where military coups emerge.

Keywords: predatory rule, military coups, socio-political analysis, frustration-aggression theory, Mali

Procedia PDF Downloads 46

Authors: Serkan Kocapinar

Abstract:

Since June 2014, the extremist terrorist group known as the Islamic State of Iraq and the Levant, with its financial resources, as well as the world’s richest in terms of human resources, is a terrorist organization utilizing the most advanced weapons. It has established a state in the occupied region, appointed provincial and district managers, and declared the so-called Caliphate. Despite being a terrorist organization, it is selling the oil which it has seized from the captured regions with low prices. Consequently, it has been achieving great income from these sales. Currently the actual number of terrorists in the area is around from 20,000 to 31,000 according to the CIA assessment. It is estimated that it has extended its domain beyond from the Middle East to the Asia-Pacific coast and has had millions of supporters worldwide. In addition, it is claimed that it has several sleeper cells in some countries and could perform very catastrophic attacks to the countries fighting against it by activating its cells when necessary. The sharp rise of ISIS in just a year has also attracted the attention of terrorist groups such as Boko Haram around the world and some groups expressed their allegiance to ISIS. With this growing power and influence, ISIS is becoming more and more effective threat for not only the region but also for the entire world. The purpose of this study is to show what lies under the rising of ISIS terror organization and how it affects the security concerns.

Keywords: ISIS, security, terrorism, threats

Procedia PDF Downloads 286

Authors: Debora Gottardello, Mireia Valverde Aparicio, Juan Llopis Taverner

Abstract:

Globalization has given rise to a great diversity in the composition of people in organizations. Diversity management is therefore key to create growth in today’s competitive global marketplace. This work develops a literature review related to the existing models for managing diversity covering the period from 1980 until 2014. Furthermore, it identifies limitations in previous models. More specifically, the literature review reveals that there is a lack of information about how these models can be adapted from the headquarters to the subsidiaries. Therefore, the contribution of this paper is to suggest how the models should be adapted when they are directed to host countries. Our aim is to highlight the limitations of the developed models with regards to the translation of the diversity management practices to the subsidiaries. Accordingly, a model that will enable MNCs to ensure a global strategy is suggested. Taking advantage of the potential incorporated in a culturally diverse work team should be at the top of every international company’s aims. Executives from headquarters need to use different attitudes when transferring diversity practices towards their subsidiaries. Further studies should reassess local practices of diversity management to find out how this universal management model is translated.

Keywords: culture diversity, diversity management, human resources management, MNCs, subsidiaries, workforce diversity

Procedia PDF Downloads 242

Authors: Alex Kizuk

Abstract:

This paper studies the trope or meme of the Siren in terms of what long-standing cultural continuities can be found in college classrooms today. Those who have raised children may remember reading from Hans Christian Anderson's 'The Little Mermaid' (1836), not to mention regaling them with colorful Disneyesque versions when they were younger. Though Anderson tempered the darker first ending of the story to give the little mermaid more agency in her salvation—a prognostic developed in Disney adaptations—nonetheless, the tale pivots on an image of a 'heavenly realm' that the mermaid may eventually come to know or comprehend as a beloved woman on dry land. Only after 300 years, however, may she hope to see that 'which lives forever' and 'rises through thin air, up to the shining stars. Just as [sea-people] rise through the water to see the lands on earth.' What students today can see in this example is a trope of the agonistic soul in a hard-won disembarkation at a harbour of knowledge--where the seeker after truth may come to know through persistence (300 years)—all that is good and true concerning human life. This paper discusses several such examples from the Great Books and popular culture to suggest that teaching in the world of the 21st century could do worse than accede to some such perennial seeking.

Keywords: the Great Books, tradition, popular culture, 21st century directions in teaching

Procedia PDF Downloads 144

Authors: Ennus Tajuddin Tamboli, Madhukar Garg, Mohd. Mujeeb, Sayeed Ahmad

Abstract:

An efficient protocol for simultaneous production of forskolin and rosmarinic acid in in vitro callus derived from the leaves of Coleus forskohlii Briq. has been developed. MS media was used for the establishment of cultures and NAA + 6-BA (1.0 ppm) was found best for callus growth. The callus was further subjected to treatment with various elicitor/precursors viz. chitosan, thidiazuron and methyl jasmonate to observe their effect on production of biomass and accumulation of secondary metabolites. The content of forskolin and rosmarinic acid were estimated by HPTLC, in comparison to natural explant which showed 2 fold and 10 fold rise in forskolin and rosmarinic acid content, respectively. Methy1 jasmonate 50 µM was found best for production of forskolin, whereas thidiazuron showed best results in the yield of rosmarinic acid, separately in static culture. However, combined treatment in suspension culture showed moderated effect for increase in secondary metabolites but the biomass increased significantly as compared to static culture.

Keywords: plant tissue culture, secondary metabolites, coleus, forskolin, rosmarinic acid, HPTLC

Procedia PDF Downloads 331

Authors: Mensah-Akoto Julius, Kenichi Matsui

Abstract:

This paper examines the impact of COVID-19 on waste management workers in Ghana. A questionnaire survey was conducted among 60 waste management workers in Accra metropolis, the capital region of Ghana, to understand the impact of the COVID-19 pandemic on waste generation, workers’ safety in collecting solid waste, and service delivery. To find out correlations between the pandemic and safety of waste management workers, a regression analysis was used. Regarding waste generation, the results show the pandemic led to the highest annual per capita solid waste generation, or 3,390 tons, in 2020. Regarding the safety of workers, the regression analysis shows a significant and inverse association between COVID-19 and waste management services. This means that contaminated wastes may infect field workers with COVID-19 due to their direct exposure. A rise in new infection cases would have a negative impact on the safety and service delivery of the workers. The result also shows that an increase in economic activities negatively impacts waste management workers. The analysis, however, finds no statistical relationship between workers’ service deliveries and employees’ salaries. The study then discusses how municipal waste management authorities can ensure safe and effective waste collection during the pandemic.

Keywords: Covid-19, waste management worker, waste collection, Ghana

Procedia PDF Downloads 182

Authors: Serge B. Provost

Abstract:

Numerous statistical inference and modeling methodologies are based on sample moments rather than the actual observations. A result justifying the validity of this approach is introduced. More specifically, it will be established that given the first n moments of a sample of size n, one can recover the original n sample points. This implies that a sample of size n and its first associated n moments contain precisely the same amount of information. However, it is efficient to make use of a limited number of initial moments as most of the relevant distributional information is included in them. Two types of density estimation techniques that rely on such moments will be discussed. The first one expresses a density estimate as the product of a suitable base density and a polynomial adjustment whose coefficients are determined by equating the moments of the density estimate to the sample moments. The second one assumes that the derivative of the logarithm of a density function can be represented as a rational function. This gives rise to a system of linear equations involving sample moments, the density estimate is then obtained by solving a differential equation. Unlike kernel density estimation, these methodologies are ideally suited to model ‘big data’ as they only require a limited number of moments, irrespective of the sample size. What is more, they produce simple closed form expressions that are amenable to algebraic manipulations. They also turn out to be more accurate as will be shown in several illustrative examples.

Keywords: density estimation, log-density, polynomial adjustments, sample moments

Procedia PDF Downloads 153

Authors: Vanaja Rao

Abstract:

In the recent times, the need for the integration of Renewable Energy Sources (RES) in a Smart Grid is on the rise. As a result of this, associated energy storage systems are known to play important roles in sustaining the efficient operation of such RES like wind power and solar power. This paper investigates the importance of location selection of Energy Storage Systems (ESSs) in a Smart Grid. Three scenarios of ESS location is studied and analyzed in a Smart Grid, which are – 1. Near the generation/source, 2. In the middle of the Grid and, 3. Near the demand/consumption. This is explained with the aim of assisting any Distribution Network Operator (DNO) in deploying the ESSs in a power network, which will significantly help reduce the costs and time of planning and avoid any damages incurred as a result of installing them at an incorrect location of a Smart Grid. To do this, the outlined scenarios mentioned above are modelled and analyzed with the National Grid’s datasets of energy generation and consumption in the UK power network. As a result, the outcome of this analysis aims to provide a better overview for the location selection of the ESSs in a Smart Grid. This ensures power system stability and security along with the optimum usage of the ESSs.

Keywords: distribution networks, energy storage system, energy security, location planning, power stability, smart grid

Procedia PDF Downloads 286

Authors: Anis A. Ansari, M. Kamil

Abstract:

The development of 3D printing technology has allowed the manufacturing industry to create parts with a high degree of automation, increased design freedom, and improved mechanical performance. Fused deposition modelling (FDM) is a 3D printing technique in which successive layers of thermoplastic polymer are deposited and controlled to create a three-dimensional product. In this study, process parameters such as nozzle temperature and printing speed were chosen to investigate their effects on hardness properties. 3D printed specimens were fabricated by an FDM 3D printer from Polylactic acid (PLA) polymer. After analysis, it was observed that the hardness property is much influenced by print speed and nozzle temperature parameters. Maximum hardness was achieved at higher print speed which indicates that the Shore D hardness is directly proportional to the print speed. Moreover, at higher print speed, it has no significant dependence on the nozzle temperature. Hardness is also influenced by nozzle temperature, though to a lesser extent. The hardness slightly lowers when the nozzle temperature is raised from 190 to 210 oC, but due to improved bonding between each raster, a further rise in temperature increases the hardness property.

Keywords: 3D printing, fused deposition modeling (FDM), polylactic acid (PLA), print speed, nozzle temperature, hardness property

Procedia PDF Downloads 75

Authors: Rebecca Dewfall, Mark Coleman, Vladimir Basabe

Abstract:

Oxide scale growth is an inevitable byproduct of the high temperature processing of steel. Blister is a phenomenon that occurs due to oxide growth, where high temperatures result in the swelling of surface scale, producing a bubble-like feature. Blisters can subsequently become embedded in the steel substrate during hot rolling in the finishing mill. This rolled in scale defect causes havoc within industry, not only with wear on machinery but loss of customer satisfaction, poor surface finish, loss of material, and profit. Even though blister is a highly prevalent issue, there is still much that is not known or understood. The classic iron oxidation system is a complex multiphase system formed of wustite, magnetite, and hematite, producing multi-layered scales. Each phase will have independent properties such as thermal coefficients, growth rate, and mechanical properties, etc. Furthermore, each additional alloying element will have different affinities for oxygen and different mobilities in the oxide phases so that oxide morphologies are specific to alloy chemistry. Therefore, blister regimes can be unique to each steel grade resulting in a diverse range of formation mechanisms. Laboratory conditions were selected to simulate industrial hot rolling with temperature ranges approximate to the formation of secondary and tertiary scales in the finishing mills. Samples with composition: 0.15Wt% C, 0.1Wt% Si, 0.86Wt% Mn, 0.036Wt% Al, and 0.028Wt% Cr, were oxidised in a thermo-gravimetric analyser (TGA), with an air velocity of 10litresmin-1, at temperaturesof 800°C, 850°C, 900°C, 1000°C, 1100°C, and 1200°C respectively. Samples were held at temperature in an argon atmosphere for 10minutes, then oxidised in air for 600s, 60s, 30s, 15s, and 4s, respectively. Oxide morphology and Blisters were characterised using EBSD, WDX, nanoindentation, FIB, and FEG-SEM imaging. Blister was found to have both a nucleation and growth process. During nucleation, the scale detaches from the substrate and blisters after a very short period, roughly 10s. The steel substrate is then exposed inside of the blister and further oxidised in the reducing atmosphere of the blister, however, the atmosphere within the blister is highly dependent upon the porosity of the blister crown. The blister crown was found to be consistently between 35-40um for all heating regimes, which supports the theory that the blister inflates, and the oxide then subsequently grows underneath. Upon heating, two modes of blistering were identified. In Mode 1 it was ascertained that the stresses produced by oxide growth will increase with increasing oxide thickness. Therefore, in Mode 1 the incubation time for blister formation is shortened by increasing temperature. In Mode 2 increase in temperature will result in oxide with a high ductility and high oxide porosity. The high oxide ductility and/or porosity accommodates for the intrinsic stresses from oxide growth. Thus Mode 2 is the inverse of Mode 1, and incubation time is increased with temperature. A new phenomenon was reported whereby blister formed exclusively through cooling at elevated temperatures above mode 2.

Keywords: FEG-SEM, nucleation, oxide morphology, surface defect

Procedia PDF Downloads 130

Authors: Akor Omachile Opaluwah

Abstract:

Entrepreneurs are heralded as a very vital force in the growth of economies. This is because they create businesses, employ people, have direct access to the local consumer, and primarily utilize local sources of raw materials, have an understanding of the immediate need of consumers, and they have the capacity to keep in motion the economy. The rise of social enterprises takes these advantages further beyond the business and economic benefits. These Social enterprises help address developmental issues in the society while maintaining a profit for their investors and shareholders. These combined roles create a unique synergy between the civil society and the market, therefore placing the social enterprise in a position where they can access directly, the benefits of the market while meeting the needs of the citizens and their environment. With such a unique position, social enterprises hold a place in the development discourse that has previously been left unexplored. This hybridisation of the functions of civil societies and the market can provide to development, practices, and benefits that have previously been only available in trace amounts. It, therefore, is imperative to understand the efficacy of social enterprises. With the discourse of social enterprises still in its early stages. This paper looks at selected social enterprise cases in Nigeria and analyses their approach and contribution to development.

Keywords: business, civil society, development, entrepreneurs, innovation, market, Nigeria, social enterprise

Procedia PDF Downloads 366

Authors: Jianhua Zhou, Yuwen Zhang

Abstract:

A two-step multigrid approach is proposed to solve the inverse heat conduction problem in a 3-D object under laser irradiation. In the first step, the location of the laser center is estimated using a coarse and uniform grid system. In the second step, the front-surface temperature is recovered in good accuracy using a multiple grid system in which fine mesh is used at laser spot center to capture the drastic temperature rise in this region but coarse mesh is employed in the peripheral region to reduce the total number of sensors required. The effectiveness of the two-step approach and the multiple grid system are demonstrated by the illustrative inverse solutions. If the measurement data for the temperature and heat flux on the back surface do not contain random error, the proposed multigrid approach can yield more accurate inverse solutions. When the back-surface measurement data contain random noise, accurate inverse solutions cannot be obtained if both temperature and heat flux are measured on the back surface.

Keywords: conduction, inverse problems, conjugated gradient method, laser

Procedia PDF Downloads 358

Authors: Mehrdad Abkenari, Alireza Rezaei, Naghmeh Pournayeb

Abstract:

There have recently been many studies and investments in developed and developing countries regarding the possibility of recycling construction waste, which are still ongoing. Since the term 'construction waste' covers a vast spectrum of materials in constructing buildings, roads and etc., many investigations are required to measure their technical performance in use as well as their time and place of use. Concrete is among the major and fundamental materials used in current construction industry. Along with the rise of population in developing countries, it is desperately required to meet the people's primary need in construction industry and on the other hand, dispose existing wastes for reducing the amount of environmental pollutants. Restrictions of natural resources and environmental pollution are the most important problems encountered by civil engineers. Reusing construction waste is an important and economic approach that not only assists the preservation of environment but also, provides us with primary raw materials. In line with consistent municipal development in disposal and reuse of construction waste, several approaches including, management of construction waste and materials, materials recycling and innovation and new inventions in materials have been predicted. This article has accordingly attempted to study the activities related to recycling of construction wastes and then, stated the economic, quantitative, qualitative and environmental results obtained.

Keywords: civil engineering, environment, recycling, construction waste

Procedia PDF Downloads 292

Authors: Melody Wong

Abstract:

Taikoo Green Ribbon is the winning scheme of International Advancing Net Zero ANZ Ideas Competition 2021 and shortlisted as a finalist of top Architectural Award “AJ100 Sustainability Initiative of the Year, 2022, demonstrating city's aspirations to reach carbon neutrality by 2050. The project showcases total design solutions to blend technology and nature to create a futuristic workplace achieving net zero within a decade. The net zero building design featured with extremely low embodied carbon emission (<250 kgCO2/sqm), significant surplus in renewable energy generation (130% of energy consumption) and various carbon capture technology. The project leverages aesthetics, user-experience, sustainability, and technology to develop over 40 design features. Utilizing AI-controlled Smart Envelope system, the possibility of naturally ventilation was maximized to adjust the microclimate to foster behavourial change. The design principle – healthy and collaborative working environment is realized with a landscaped sky-track with kinetic energy pads, natural ventilated open space with edible plants across floors, and 500-seat open-space rooftop theatre to reshape and redefine the new generation of workplaces.

Keywords: NetZero, zero carbon, green, sustainability

Procedia PDF Downloads 64

Authors: Woei-Shyan Lee, Hao-Chien Kao

Abstract:

The impact deformation and fracture behaviour of cobalt-based Haynes 188 superalloy are investigated by means of a split Hopkinson pressure bar. Impact tests are performed at strain rates ranging from 1×103 s-1 to 5×103 s-1 and temperatures between 25°C and 800°C. The experimental results indicate that the flow response and fracture characteristics of cobalt-based Haynes 188 superalloy are significantly dependent on the strain rate and temperature. The flow stress, work hardening rate and strain rate sensitivity all increase with increasing strain rate or decreasing temperature. It is shown that the impact response of the Haynes 188 specimens is adequately described by the Zerilli-Armstrong fcc model. The fracture analysis results indicate that the Haynes 188 specimens fail predominantly as the result of intensive localised shearing. Furthermore, it is shown that the flow localisation effect leads to the formation of adiabatic shear bands. The fracture surfaces of the deformed Haynes 188 specimens are characterised by dimple- and / or cleavage-like structure with knobby features. The knobby features are thought to be the result of a rise in the local temperature to a value greater than the melting point.

Keywords: Haynes 188 alloy, impact, strain rate and temperature effect, adiabatic shearing

Procedia PDF Downloads 350

Authors: Krisna Damayanti

Abstract:

Negative issue about the relationship between auditors and clients often heard. It arises in view of the rise of a variety of phenomena resulting from the audit practice of greed and do not appreciate the independence of the audit profession and professional code of ethics. It is a logical consequence of the practice of capitalism in accounting. The purpose of this paper would like to uncover the existing auditing practices in Indonesia, especially Java, which is associated with a strong influence of Javanese culture with reluctant/"shy", politely, "legowo", "ngemong" friendly, "not mentholo", "tepo seliro", "ngajeni", "acquiescent". The method used by interpretive approach that emphasizes the role of language, interpret and understand and see social reality as something other than a label, name or concept. Auditing practices in each country has a culture that will affect the standard set by those regulatory standards although there has been an adaptation of IAS. In Indonesia the majority of parties dominated by Javanesse racial regulators, so Java culture is embedded in every audit practices thus conditions in Java requires auditors to behave like that, sometimes interfere with standard Java code of conduct that must be executed by an auditor. Auditors who live in Java have the characters of Javanese culture that is hard to avoid in the audit practice. However, in practice, the auditor still are relevant in their profession.

Keywords: auditors, java, character, profession, code of ethics, client

Procedia PDF Downloads 425

Authors: Spyridon Plakoudas

Abstract:

After the capture of Al-Raqqah and the defeat of the short-lived Islamic Caliphate in 2017, everyone predicted the end of ISIS. However, ISIS proved far more resilient than initially thought. The militant group quickly regrouped from its defeat and started a low-intensity guerrilla campaign in central Iraq (near Kirkuk and Mosul) and north-eastern Syria (near Deir ez-Zorr). At the same time, ISIS doubled down on its cyber-campaign; actually, ISIS is as active on the cyber-domain as during the peak of its power in 2015. This paper, a spin-off paper from a co-authored book on the Syrian Civil War (due to be published by Rowman and Littlefield), intends to examine how ISIS operates in the cyber-domain and how this "Cyber-Caliphate" under re-construction is associated with its post-2017 strategy. This paper will draw on the discipline of War Studies (with an emphasis on Cyber-Security and Insurgency / Counter-Insurgency) and will benefit from the insights of interviewed experts on the field (e.g., Hassan Hasssan). This paper will explain how the successful operation of ISIS in the cyber-space preserves the myth of the “caliphate” amongst its worldwide followers (against the odds) and sustains the group’s ongoing insurgency in Syria and Iraq; in addition, this paper will suggest how this cyber-threat can be countered best.

Keywords: ISIS, cyber-jihad, Syrian Civil War, cyber-terrorism, insurgency and counter-insurgency

Procedia PDF Downloads 115

Authors: A. K. O’Loughlin

Abstract:

Identity doesn’t exist in discrete categories as it is defined. Kevin Kumashiro reveals the phrase 'an impossibility of identity' in Troubling Education (2000), an investigation of the intersections of culture and gender and the impact of erasure for queer POC identity. This underscores the essentiality of an insider or an outsider identity and the appearance of 'contradiction' or impossibility of these identities. The contradictions between us as subject in our own stories and in the stories of others are often silenced. This silencing of complex, 'contradicting' identity has unmissable implications in the classroom; the developing student in question is done a serious disservice, from which they may never recover. There is no more important point of contact than the teacher, for willingness to encounter a developing person as they are, not as we already think they are, or 'know' them to be, or think they should be. To decide how to regard them based on our own unilateral identity and its associated exhortations and injunctions is, as Hannah Arendt writes in The Origins of Totalitarianism (1951), to sell off our ability to rise, human-like, to the challenge of investigating things as they are. A re-reading of Kumashiro’s impossibility of identity becomes possible through the investigation of pluralism. Identities become possible and un-paradoxical by the notion that contradictions are not problems that an individual is not unilateral, but plural. In this paper, we investigate how philosophies of pluralism can inform our understanding of impossibility of identity in classroom curriculum and pedagogy.

Keywords: identity, gender, culture, pluralism, education, philosophy of education, queer theory, philosophy of mind, adolescent development

Procedia PDF Downloads 282

Authors: Hung Nguyen

Abstract:

With the rise of global supply chain network, the choice of supply chain orientation is critical. The alignment between cultural similarity and supply chain information exchange could help identify appropriate supply chain orientations, which would differentiate the stronger competitors and performers from the weaker ones. Through developing a taxonomy, this study examined whether the choices of action programs and manufacturing performance differ depending on the levels of attainment cultural similarity and information exchange. This study employed statistical tests on a large-scale dataset consisting of 680 manufacturing plants from various cultures and industries. Firms need to align cultural practices with the level of information exchange in order to achieve good overall business performance. There appeared to be consistent three major orientations: the Proactive, the Initiative and the Reactive. Firms are experiencing higher payoffs from various improvements are the ones successful alignment in both information exchange and cultural similarity The findings provide step-by-step decision making for supply chain information exchange and offer guidance especially for global supply chain managers. In including both cultural similarity and information exchange, this paper adds greater comprehensiveness and richness to the supply chain literature.

Keywords: culture, information exchange, supply chain orientation, similarity

Procedia PDF Downloads 346

Authors: Zubier Arfan, Paul Johnson

Abstract:

The electronification of financial markets and the rise of algorithmic trading has sparked a lot of interest from the mathematical community, for the market making-problem in particular. The research presented in this short paper solves the classic stochastic control problem in order to derive the strategy for a market-maker. It also shows how to calibrate and simulate the strategy with real limit order book data for back-testing. The ambiguity of limit-order priority in back-testing is dealt with by considering optimistic and pessimistic priority scenarios. The model, although it does outperform a naive strategy, assumes constant volatility, therefore, is not best suited to the LOB data. The Heston model is introduced to describe the price and variance process of the asset. The Trader's constant absolute risk aversion utility function is optimised by numerically solving a 3-dimensional Hamilton-Jacobi-Bellman partial differential equation to find the optimal limit order quotes. The results show that the stochastic volatility market-making model is more suitable for a risk-averse trader and is also less sensitive to calibration error than the constant volatility model.

Keywords: market-making, market-microsctrucure, stochastic volatility, quantitative trading

Procedia PDF Downloads 136

Authors: Daniel D'Souza, Ping Zou

Abstract:

The period before, during, and after menopause is a sensitive time for women as they experience intense physical and psychological health changes and symptoms. These changes accompany the hormonal changes that mark the end of a woman’s reproductive age. To help mitigate and cope with these changes, prompt and correct treatment is needed. eHealth has emerged as a branch of telemedicine in the past few decades as an alternate avenue for patients to receive care quickly and conveniently, as it relies on the Internet and computers. Within the past few years, eHealth has also given rise to mHealth, which is the use of personal mobile devices to receive treatment and care. However, there is a lack of study on their use for menopause. This review aimed to review and summarize the literature for eHealth or mHealth and menopause. Several databases related to women’s health and digital health were searched for original studies about eHealth or mHealth and menopause. The search yielded 25 results. The results were generally positive, with these interventions being feasible and having positive effects on physical and psychosocial outcomes. However, several issues were raised regarding their design process that may inadvertently prevent these interventions from addressing the needs of all potential users. Therefore, while eHealth and mHealth certainly represent a future model of healthcare delivery for menopausal women, further research and design modifications are needed before this can happen.

Keywords: eHealth, menopause, mHealth, midlife women

Procedia PDF Downloads 128

Authors: Fatemeh Khalili Varnamkhasti

Abstract:

Numerous nations have recognized the critical ought to address natural issues, such as discuss contamination, squander transfer, worldwide warming, and common asset consumption, through the application of green innovation. The rise of cleverly advances has driven mechanical basic changes that will offer assistance accomplish carbon decrease. Manufactured insights (AI) innovation is an imperative portion of digitalization, giving unused mechanical apparatuses and bearings for the moo carbon advancement of endeavors. Quickening the brilliantly change of fabricating industry is an critical vital choice to realize the green advancement change. The reason why fabricating insights can advance the advancement of green advancement execution is that fabricating insights is conducive to the generation of "innovation advancement impact" and "fetched decrease impact" so as to advance green innovation advancement, at that point viably increment the alluring yields and essentially diminish the undesirable yields. AI improvement will boost GTI as it were when the escalated of natural direction and organization environment is over a certain edge esteem. In any case, the AI improvement spoken to by mechanical robot applications still has no self-evident impact on GTI, indeed, when the R&D venture surpasses a certain edge.

Keywords: greenhouse gas emissions, green infrastructure, artificial intelligence, environmental protection

Procedia PDF Downloads 49

Authors: I. V. Kuzminov

Abstract:

The research is dedicated to the issue of Bosporus evolution and its key role in the Black Sea forming. Up till nowadays, there is no distinct picture of the historical and geographical events of the last 10 thousand years on the territory from Altai up to the Alps. The present article is an attempt to clarify and, moreover, link the presented version to the historical and climatic events of this period. The paper is a development of the basic idea stated in "Hypothesis on the Black Sea origin". The succession of events in dynamics is offered in this article. In the article, it is shown that fluctuation of the level of the World Ocean is a mirror of the basic events connected with the climate on the Earth on the one hand and hydraulic processes on the other hand. In the present article, it is come out with the assumption that at the formation of passage, there were some cycles of change in a level of the World ocean. The phase of the beginning of climate warming is characterized by an increase in the level of inland water bodies on the way of meltwater runoff and an increase in the World ocean level. The end of the warming phase is characterized by the continuation of a rise in the level of the World ocean and the drying up of inland water bodies deprived of meltwater replenishment.

Keywords: Bosporus, Ryan-Pitman hypothesis, fluctuations of the World Ocean level, the Paratethys Sea, catastrophic breakthrough

Procedia PDF Downloads 102

Authors: Abhipsa Mohanty, Harit Jha

Abstract:

The world's energy demands are continuing to rise, resulting in a worldwide energy crisis and environmental pollution. Because of finite, declining supply and environmental damage, reliance on fossil fuels is unsustainable. As a result, experts are concentrating on alternative, renewable, and carbon-free energy sources. Energy sources that are both environmentally and economically sustainable are required. Microbial fuel cells (MFCs) have recently received a lot of attention due to their low operating temperatures and ability to use a variety of biodegradable substrates as fuel. There are single-chamber MFCs as well as traditional MFCs with anode and cathode compartments. Bioelectricity is produced when microorganisms actively catabolize substrate. MFCs can be used as a power source in small devices like biosensors. Understanding of its components, microbiological processes, limiting variables, and construction designs in MFC systems must be simplified, and large-scale systems must be developed for them to be cost-effective as well as increase electricity production. The purpose of this research was to review current microbiology knowledge in the field of electricity. The manufacturing process, the materials, and procedures utilized to construct the technology, as well as the applications of MFC technology, are all covered.

Keywords: bio-electricity, exoelectrogenic bacteria, microbial fuel cells, soil microorganisms

Procedia PDF Downloads 82

Authors: Gaby Fahmy

Abstract:

The last decades have seen a rise in metabolic disorders like diabetes, obesity, and fatty liver disease around the world. Environmental factors, especially nutrition, have contributed to this increase. Additionally, pre-conceptional parental nutritional choices have been shown to result in epigenetic modifications affecting gene expression during the developmental process in-utero. These epigenetic modifications have also been seen to extend to the following offspring in a trans-generational effect. This further highlights the significance and relevance of epigenetics and epigenetic tags, which were previously thought to be stripped in newly formed embryos. Suitable prenatal nutrition may partially counteract adverse outcomes caused by exposures to environmental contaminants, ultimately resulting in improved metabolic profiles like body weight and glucose homeostasis. This was seen in patients who were given dietary interventions like restrictive caloric intake, intermittent fasting, and time-restricted feeding. Changes in nutrition are pivotal in the regulation of epigenetic modifications that are transgenerational. For example, dietary choices such as fatty foods vs. vegetables and nuts in fathers were shown to significantly affect sperm motility and volume. This was pivotal in understanding the importance of paternal inheritance. Further research in the field is needed as it remains unclear how many generations are affected by these changes.

Keywords: epigenetics, transgenerational, diet, fasting

Procedia PDF Downloads 85

Authors: B. Yanıktepe, C. Özalp, B. Şahin

Abstract:

Delta wing planform is an essential aerodynamic configuration, which could be effectively used at relatively high angles of attack than conventional wings in subsonic flow conditions. The flow over delta wings can be characterized by a pair of leading edge vortices emanating from wing apex. Boundary layer separation causes these vortical structures formed by rolling up of viscous flow sheet. This flow separation mechanism is occurred due to angle of attack and sharp leading edges of the delta wing. Therefore, complexity and variety in planform designs rise to catch the best under abnormal flow conditions. The present experimental study investigates the near surface flow structure and aerodynamic flow characteristics of X-45 type non-slender delta wing planform using dye visualization, Stereoscopic Particle Image Velocimetry (stereo-PIV). The instantaneous images are acquired on the plan-view plane within 5o≤α≤20o to calculate the time-averaged flow data. It can be concluded that vortical flow with a pair of well-defined LEVs over X-45 develop at very low angles of attack, secondary vortex are also evident and form close to the wing surface similar to delta and lambda planforms. The stall occurs at an angle of attack α=32o.

Keywords: aerodynamic, delta wing, PIV, vortex breakdown

Procedia PDF Downloads 409

Authors: Pavlo Selyshchev

Abstract:

A theoretical approach to describe kinetic of heat transfer between an irradiated sample and environment is developed via formalism of the Complex systems and kinetic equations. The irradiated material is a metastable system with non-linear feedbacks, which can give rise to different regimes of buildup and annealing of radiation-induced defects, heating and heat transfer with environment. Irradiation with energetic particles heats the sample and produces defects of the crystal lattice of the sample. The crystal with defects accumulates extra (non-thermal) energy, which is transformed into heat during the defect annealing. Any increase of temperature leads to acceleration of defect annealing, to additional transformation of non-thermal energy into heat and to further growth of the temperature. Thus a non-linear feedback is formed. It is shown that at certain conditions of irradiation this non-linear feedback leads to self-oscillations of the defect density, the temperature of the irradiated sample and the heat transfer between the sample and environment. Simulation and analysis of these phenomena is performed. The frequency of the self-oscillations is obtained. It is determined that the period of the self-oscillations is varied from minutes to several hours depending on conditions of irradiation and properties of the sample. Obtaining results are compared with experimental ones.

Keywords: irradiation, heat transfer, non-linear feed-back, self-oscillations

Procedia PDF Downloads 218