Search results for: stress distribution
1116 Accurate Calculation of the Penetration Depth of a Bullet Using ANSYS
Authors: Eunsu Jang, Kang Park
Abstract:
In developing an armored ground combat vehicle (AGCV), it is a very important step to analyze the vulnerability (or the survivability) of the AGCV against enemy’s attack. In the vulnerability analysis, the penetration equations are usually used to get the penetration depth and check whether a bullet can penetrate the armor of the AGCV, which causes the damage of internal components or crews. The penetration equations are derived from penetration experiments which require long time and great efforts. However, they usually hold only for the specific material of the target and the specific type of the bullet used in experiments. Thus, penetration simulation using ANSYS can be another option to calculate penetration depth. However, it is very important to model the targets and select the input parameters in order to get an accurate penetration depth. This paper performed a sensitivity analysis of input parameters of ANSYS on the accuracy of the calculated penetration depth. Two conflicting objectives need to be achieved in adopting ANSYS in penetration analysis: maximizing the accuracy of calculation and minimizing the calculation time. To maximize the calculation accuracy, the sensitivity analysis of the input parameters for ANSYS was performed and calculated the RMS error with the experimental data. The input parameters include mesh size, boundary condition, material properties, target diameter are tested and selected to minimize the error between the calculated result from simulation and the experiment data from the papers on the penetration equation. To minimize the calculation time, the parameter values obtained from accuracy analysis are adjusted to get optimized overall performance. As result of analysis, the followings were found: 1) As the mesh size gradually decreases from 0.9 mm to 0.5 mm, both the penetration depth and calculation time increase. 2) As diameters of the target decrease from 250mm to 60 mm, both the penetration depth and calculation time decrease. 3) As the yield stress which is one of the material property of the target decreases, the penetration depth increases. 4) The boundary condition with the fixed side surface of the target gives more penetration depth than that with the fixed side and rear surfaces. By using above finding, the input parameters can be tuned to minimize the error between simulation and experiments. By using simulation tool, ANSYS, with delicately tuned input parameters, penetration analysis can be done on computer without actual experiments. The data of penetration experiments are usually hard to get because of security reasons and only published papers provide them in the limited target material. The next step of this research is to generalize this approach to anticipate the penetration depth by interpolating the known penetration experiments. This result may not be accurate enough to be used to replace the penetration experiments, but those simulations can be used in the early stage of the design process of AGCV in modelling and simulation stage.Keywords: ANSYS, input parameters, penetration depth, sensitivity analysis
Procedia PDF Downloads 3831115 Using GIS for Assessment and Modelling of Oil Spill Risk at Vulnerable Coastal Resources: Of Misratah Coast, Libya
Authors: Abduladim Maitieg
Abstract:
The oil manufacture is one of the main productive activities in Libya and has a massive infrastructure, including offshore drilling and exploration and wide oil export platform sites that located in coastal area. There is a threat to marine and coastal area of oil spills is greatest in those sites with a high spills comes from urban and industry, parallel to that, monitoring oil spills and risk emergency strategy is weakness, An approach for estimating a coastal resources vulnerability to oil spills is presented based on abundance, environmental and Scio-economic importance, distance to oil spill resources and oil risk likelihood. As many as 10 coastal resources were selected for oil spill assessment at the coast. This study aims to evaluate, determine and establish vulnerable coastal resource maps and estimating the rate of oil spill comes for different oil spill resources in Misratah marine environment. In the study area there are two type of oil spill resources, major oil resources come from offshore oil industries which are 96 km from the Coast and Loading/Uploading oil platform. However, the miner oil resources come from urban sewage pipes and fish ports. In order to analyse the collected database, the Geographic information system software has been used to identify oil spill location, to map oil tracks in front of study area, and developing seasonal vulnerable costal resources maps. This work shows that there is a differential distribution of the degree of vulnerability to oil spills along the coastline, with values ranging from high vulnerability and low vulnerability, and highlights the link between oil spill movement and coastal resources vulnerability. The results of assessment found most of costal freshwater spring sites are highly vulnerable to oil spill due to their location on the intertidal zone and their close to proximity to oil spills recourses such as Zreag coast. Furthermore, the Saltmarsh coastline is highly vulnerable to oil spill risk due to characterisation as it contains a nesting area of sea turtles and feeding places for migratory birds and the . Oil will reach the coast in winter season according to oil spill movement. Coastal tourist beaches in the north coast are considered as highly vulnerable to oil spill due to location and closeness to oil spill resources.Keywords: coastal recourses vulnerability, oil spill trajectory, gnome software, Misratah coast- Libya, GIS
Procedia PDF Downloads 3051114 Monte Carlo Simulation of Thyroid Phantom Imaging Using Geant4-GATE
Authors: Parimalah Velo, Ahmad Zakaria
Abstract:
Introduction: Monte Carlo simulations of preclinical imaging systems allow opportunity to enable new research that could range from designing hardware up to discovery of new imaging application. The simulation system which could accurately model an imaging modality provides a platform for imaging developments that might be inconvenient in physical experiment systems due to the expense, unnecessary radiation exposures and technological difficulties. The aim of present study is to validate the Monte Carlo simulation of thyroid phantom imaging using Geant4-GATE for Siemen’s e-cam single head gamma camera. Upon the validation of the gamma camera simulation model by comparing physical characteristic such as energy resolution, spatial resolution, sensitivity, and dead time, the GATE simulation of thyroid phantom imaging is carried out. Methods: A thyroid phantom is defined geometrically which comprises of 2 lobes with 80mm in diameter, 1 hot spot, and 3 cold spots. This geometry accurately resembling the actual dimensions of thyroid phantom. A planar image of 500k counts with 128x128 matrix size was acquired using simulation model and in actual experimental setup. Upon image acquisition, quantitative image analysis was performed by investigating the total number of counts in image, the contrast of the image, radioactivity distributions on image and the dimension of hot spot. Algorithm for each quantification is described in detail. The difference in estimated and actual values for both simulation and experimental setup is analyzed for radioactivity distribution and dimension of hot spot. Results: The results show that the difference between contrast level of simulation image and experimental image is within 2%. The difference in the total count between simulation and actual study is 0.4%. The results of activity estimation show that the relative difference between estimated and actual activity for experimental and simulation is 4.62% and 3.03% respectively. The deviation in estimated diameter of hot spot for both simulation and experimental study are similar which is 0.5 pixel. In conclusion, the comparisons show good agreement between the simulation and experimental data.Keywords: gamma camera, Geant4 application of tomographic emission (GATE), Monte Carlo, thyroid imaging
Procedia PDF Downloads 2641113 The Use of a Novel Visual Kinetic Demonstration Technique in Student Skill Acquisition of the Sellick Cricoid Force Manoeuvre
Authors: L. Nathaniel-Wurie
Abstract:
The Sellick manoeuvre a.k.a the application of cricoid force (CF), was first described by Brian Sellick in 1961. CF is the application of digital pressure against the cricoid cartilage with the intention of posterior force causing oesophageal compression against the vertebrae. This is designed to prevent passive regurgitation of gastric contents, which is a major cause of morbidity and mortality during emergency airway management inside and outside of the hospital. To the authors knowledge, there is no universally standardised training modality and, therefore, no reliable way to examine if there are appropriate outcomes. If force is not measured during training, how can one surmise that appropriate, accurate, or precise amounts of force are being used routinely. Poor homogeneity in teaching and untested outcomes will correlate with reduced efficacy and increased adverse effects. For this study, the accuracy of force delivery in trained professionals was tested, and outcomes contrasted against a novice control and a novice study group. In this study, 20 operating department practitioners were tested (with a mean experience of 5.3years of performing CF). Subsequent contrast with 40 novice students who were randomised into one of two arms. ‘Arm A’ were explained the procedure, then shown the procedure then asked to perform CF with the corresponding force measurement being taken three times. Arm B had the same process as arm A then before being tested, they had 10, and 30 Newtons applied to their hands to increase intuitive understanding of what the required force equated to, then were asked to apply the equivalent amount of force against a visible force metre and asked to hold that force for 20 seconds which allowed direct visualisation and correction of any over or under estimation. Following this, Arm B were then asked to perform the manoeuvre, and the force generated measured three times. This study shows that there is a wide distribution of force produced by trained professionals and novices performing the procedure for the first time. Our methodology for teaching the manoeuvre shows an improved accuracy, precision, and homogeneity within the group when compared to novices and even outperforms trained practitioners. In conclusion, if this methodology is adopted, it may correlate with higher clinical outcomes, less adverse events, and more successful airway management in critical medical scenarios.Keywords: airway, cricoid, medical education, sellick
Procedia PDF Downloads 721112 Association between a Serotonin Re-Uptake Transporter Gene Polymorphism and Mucosal Serotonin Level in Women Patients with Irritable Bowel Syndrome and Healthy Control: A Pilot Study from Northern India
Authors: Sunil Kumar, Uday C. Ghoshal
Abstract:
Background and aims: Serotonin (5-hydroxtryptamine, 5-HT) is an important factor in gut function, playing key roles in intestinal peristalsis and secretion, and in sensory signaling in the brain-gut axis. Removal from its sites of action is mediated by a specific protein called the serotonin reuptake transporter (SERT). Polymorphisms in the promoter region of the SERT gene have effects on transcriptional activity, resulting in altered 5-HT reuptake efficiency. Functional polymorphisms may underlie disturbance in gut function in individuals suffering with disorders such as irritable bowel syndrome (IBS). The aim of this study was to assess the potential association between SERT polymorphisms and the diarrhea predominant IBS (D-IBS) phenotype Subjects: A total of 36 northern Indian female patients and 55 female northern Indian healthy controls (HC) were subjected to genotyping. Methods: Leucocyte DNA of all subjects was analyzed by polymerase chain reaction based technologies for SERT polymorphisms, specifically the insertion/deletion polymorphism in the promoter (SERT-P). Statistical analysis was performed to assess association of SERT polymorphism allele with the D-IBS phenotype. Results: The frequency of distribution of SERT-P gene was comparable between female patients with IBS and HC (p = 0.086). However, frequency of SERT-P deletion/deletion genotype was significantly higher in female patients with D-IBS compared to C-IBS and A-IBS [17/19 (89.5%) vs. 4/12 (33.3%) vs. 1/5 (20%), p=0.001, respectively]. The mucosal level of serotonin was higher in D-IBS compared to C-IBS and A-IBS [Median, range (159.26, 98.78–212.1) vs. 110.4, 67.87–143.53 vs. 92.34, 78.8–166.3 pmol/mL, p=0.001, respectively]. The mucosal level of serotonin was higher in female patients with IBS with SERT-P deletion/deletion genotype compared deletion/insertion and insertion/insertion [157.65, 67.87–212.1 vs. 110.4, 78.1–143.32 vs. 100.5, 69.1–132.03 pmol/mL, p=0.001, respectively]. Patients with D-IBS with deletion/deletion genotype more often reported symptoms of abdominal pain, discomfort (p=0.025) and bloating (p=0.039). Symptoms development following lactose ingestion was strongly associated with D-IBS and SERT-P deletion/deletion genotype (p=0.004). Conclusions: Significant association was observed between D-IBS and the SERT-P deletion/deletion genotype, suggesting that the serotonin transporter is a potential candidate gene for D-IBS in women.Keywords: serotonin, SERT, inflammatory bowel disease, genetic polymorphism
Procedia PDF Downloads 3301111 Musculoskeletal Disorders among Employees of an Assembly Industrial Workshop: Biomechanical Constrain’s Semi-Quantitative Analysis
Authors: Lamia Bouzgarrou, Amira Omrane, Haithem Kalel, Salma Kammoun
Abstract:
Background: During recent decades, mechanical and electrical industrial sector has greatly expanded with a significant employability potential. However, this sector faces the increasing prevalence of musculoskeletal disorders with heavy consequences associated with direct and indirect costs. Objective: The current intervention was motivated by large musculoskeletal upper limbs and back disorders frequency among the operators of an assembly workshop in a leader company specialized in sanitary equipment and water and gas connections. We aimed to identify biomechanical constraints among these operators through activity and biomechanical exposures semi-quantitative analysis based on video recordings and MUSKA-TMS software. Methods: We conducted, open observations and exploratory interviews at first, in order to overall understand work situation. Then, we analyzed operator’s activity through systematic observations and interviews. Finally, we conducted a semi-quantitative biomechanical constraints analysis with MUSKA-TMS software after representative activity period video recording. The assessment of biomechanical constrains was based on different criteria; biomechanical characteristics (work positions), aggravating factor (cold, vibration, stress, etc.) and exposure time (duration and frequency of solicitations, recovery phase); with a synthetic score of risk level variable from 1 to 4 (1: low risk of developing MSD and 4: high risk). Results: Semi-quantitative analysis objective many elementary operations with higher biomechanical constrains like high repetitiveness, insufficient recovery time and constraining angulation of shoulders, wrists and cervical spine. Among these risky elementary operations we sited the assembly of sleeve with the body, the assembly of axis, and the control on testing table of gas valves. Transformation of work situations were recommended, covering both the redevelopment of industrial areas and the integration of new tools and equipment of mechanical handling that reduces operator exposure to vibration. Conclusion: Musculoskeletal disorders are complex and costly disorders. Moreover, an approach centered on the observation of the work can promote the interdisciplinary dialogue and exchange between actors with the objective to maximize the performance of a company and improve the quality of life of operators.Keywords: musculoskeletal disorders, biomechanical constrains, semi-quantitative analysis, ergonomics
Procedia PDF Downloads 1541110 Research on Configuration of Large-Scale Linear Array Feeder Truss Parabolic Cylindrical Antenna of Satellite
Authors: Chen Chuanzhi, Guo Yunyun
Abstract:
The large linear array feeding parabolic cylindrical antenna of the satellite has the ability of large-area line focusing, multi-directional beam clusters simultaneously in a certain azimuth plane and elevation plane, corresponding quickly to different orientations and different directions in a wide frequency range, dual aiming of frequency and direction, and combining space power. Therefore, the large-diameter parabolic cylindrical antenna has become one of the new development directions of spaceborne antennas. Limited by the size of the rocked fairing, the large-diameter spaceborne antenna is required to be small mass and have a deployment function. After being orbited, the antenna can be deployed by expanding and be stabilized. However, few types of structures can be used to construct large cylindrical shell structures in existing structures, which greatly limits the development and application of such antennas. Aiming at high structural efficiency, the geometrical characteristics of parabolic cylinders and mechanism topological mapping law to the expandable truss are studied, and the basic configuration of deployable truss with cylindrical shell is structured. Then a modular truss parabolic cylindrical antenna is designed in this paper. The antenna has the characteristics of stable structure, high precision of reflecting surface formation, controllable motion process, high storage rate, and lightweight, etc. On the basis of the overall configuration comprehensive theory and optimization method, the structural stiffness of the modular truss parabolic cylindrical antenna is improved. And the bearing density and impact resistance of support structure are improved based on the internal tension optimal distribution method of reflector forming. Finally, a truss-type cylindrical deployable support structure with high constriction-deployment ratio, high stiffness, controllable deployment, and low mass is successfully developed, laying the foundation for the application of large-diameter parabolic cylindrical antennas in satellite antennas.Keywords: linear array feed antenna, truss type, parabolic cylindrical antenna, spaceborne antenna
Procedia PDF Downloads 1441109 National Assessment for Schools in Saudi Arabia: Score Reliability and Plausible Values
Authors: Dimiter M. Dimitrov, Abdullah Sadaawi
Abstract:
The National Assessment for Schools (NAFS) in Saudi Arabia consists of standardized tests in Mathematics, Reading, and Science for school grade levels 3, 6, and 9. One main goal is to classify students into four categories of NAFS performance (minimal, basic, proficient, and advanced) by schools and the entire national sample. The NAFS scoring and equating is performed on a bounded scale (D-scale: ranging from 0 to 1) in the framework of the recently developed “D-scoring method of measurement.” The specificity of the NAFS measurement framework and data complexity presented both challenges and opportunities to (a) the estimation of score reliability for schools, (b) setting cut-scores for the classification of students into categories of performance, and (c) generating plausible values for distributions of student performance on the D-scale. The estimation of score reliability at the school level was performed in the framework of generalizability theory (GT), with students “nested” within schools and test items “nested” within test forms. The GT design was executed via a multilevel modeling syntax code in R. Cut-scores (on the D-scale) for the classification of students into performance categories was derived via a recently developed method of standard setting, referred to as “Response Vector for Mastery” (RVM) method. For each school, the classification of students into categories of NAFS performance was based on distributions of plausible values for the students’ scores on NAFS tests by grade level (3, 6, and 9) and subject (Mathematics, Reading, and Science). Plausible values (on the D-scale) for each individual student were generated via random selection from a statistical logit-normal distribution with parameters derived from the student’s D-score and its conditional standard error, SE(D). All procedures related to D-scoring, equating, generating plausible values, and classification of students into performance levels were executed via a computer program in R developed for the purpose of NAFS data analysis.Keywords: large-scale assessment, reliability, generalizability theory, plausible values
Procedia PDF Downloads 51108 Intensification of Heat Transfer Using AL₂O₃-Cu/Water Hybrid Nanofluid in a Circular Duct Using Inserts
Authors: Muluken Biadgelegn Wollele, Mebratu Assaye Mengistu
Abstract:
Nanotechnology has created new opportunities for improving industrial efficiency and performance. One of the proposed approaches to improving the effectiveness of temperature exchangers is the use of nanofluids to improve heat transfer performance. The thermal conductivity of nanoparticles, as well as their size, diameter, and volume concentration, all played a role in influencing the rate of heat transfer. Nanofluids are commonly used in automobiles, energy storage, electronic component cooling, solar absorbers, and nuclear reactors. Convective heat transfer must be improved when designing thermal systems in order to reduce heat exchanger size, weight, and cost. Using roughened surfaces to promote heat transfer has been tried several times. Thus, both active and passive heat transfer methods show potential in terms of heat transfer improvement. There will be an added advantage of enhanced heat transfer due to the two methods adopted; however, pressure drop must be considered during flow. Thus, the current research aims to increase heat transfer by adding a twisted tap insert in a plain tube using a working fluid hybrid nanofluid (Al₂O₃-Cu) with a base fluid of water. A circular duct with inserts, a tube length of 3 meters, a hydraulic diameter of 0.01 meters, and tube walls with a constant heat flux of 20 kW/m² and a twist ratio of 125 was used to investigate Al₂O₃-Cu/H₂O hybrid nanofluid with inserts. The temperature distribution is better than with conventional tube designs due to stronger tangential contact and swirls in the twisted tape. The Nusselt number values of plain twisted tape tubes are 1.5–2.0 percent higher than those of plain tubes. When twisted tape is used instead of plain tube, performance evaluation criteria improve by 1.01 times. A heat exchanger that is useful for a number of heat exchanger applications can be built utilizing a mixed flow of analysis that incorporates passive and active methodologies.Keywords: nanofluids, active method, passive method, Nusselt number, performance evaluation criteria
Procedia PDF Downloads 681107 The Effects of Collaborative Videogame Play on Flow Experience and Mood
Authors: Eva Nolan, Timothy Mcnichols
Abstract:
Gamers spend over 3 billion hours collectively playing video games a week, which is arguably not nearly enough time to indulge in the many benefits gaming has to offer. Much of the previous research on video gaming is centered on the effects of playing violent video games and the negative impacts they have on the individual. However, there is a dearth of research in the area of non-violent video games, specifically the emotional and cognitive benefits playing non-violent games can offer individuals. Current research in the area of video game play suggests there are many benefits to playing for an individual, such as decreasing symptoms of depression, decreasing stress, increasing positive emotions, inducing relaxation, decreasing anxiety, and particularly improving mood. One suggestion as to why video games may offer such benefits is that they possess ideal characteristics to create and maintain flow experiences, which in turn, is the subjective experience where an individual obtains a heightened and improved state of mind while they are engaged in a task where a balance of challenge and skill is found. Many video games offer a platform for collaborative gameplay, which can enhance the emotional experience of gaming through the feeling of social support and social inclusion. The present study was designed to examine the effects of collaborative gameplay and flow experience on participants’ perceived mood. To investigate this phenomenon, an in-between subjects design involving forty participants were randomly divided into two groups where they engaged in solo or collaborative gameplay. Each group represented an even number of frequent gamers and non-frequent gamers. Each participant played ‘The Lego Movie Videogame’ on the Playstation 4 console. The participant’s levels of flow experience and perceived mood were measured by the Flow State Scale (FSS) and the Positive and Negative Affect Schedule (PANAS). The following research hypotheses were investigated: (i.) participants in the collaborative gameplay condition will experience higher levels of flow experience and higher levels of mood than those in the solo gameplay condition; (ii.) participants who are frequent gamers will experience higher levels of flow experience and higher levels of mood than non-frequent gamers; and (iii.) there will be a significant positive relationship between flow experience and mood. If the estimated findings are supported, this suggests that engaging in collaborative gameplay can be beneficial for an individual’s mood and that experiencing a state of flow can also enhance an individual’s mood. Hence, collaborative gaming can be beneficial to promote positive emotions (higher levels of mood) through engaging an individual’s flow state.Keywords: collaborative gameplay, flow experience, mood, games, positive emotions
Procedia PDF Downloads 3281106 Flood Hazard Assessment and Land Cover Dynamics of the Orai Khola Watershed, Bardiya, Nepal
Authors: Loonibha Manandhar, Rajendra Bhandari, Kumud Raj Kafle
Abstract:
Nepal’s Terai region is a part of the Ganges river basin which is one of the most disaster-prone areas of the world, with recurrent monsoon flooding causing millions in damage and the death and displacement of hundreds of people and households every year. The vulnerability of human settlements to natural disasters such as floods is increasing, and mapping changes in land use practices and hydro-geological parameters is essential in developing resilient communities and strong disaster management policies. The objective of this study was to develop a flood hazard zonation map of Orai Khola watershed and map the decadal land use/land cover dynamics of the watershed. The watershed area was delineated using SRTM DEM, and LANDSAT images were classified into five land use classes (forest, grassland, sediment and bare land, settlement area and cropland, and water body) using pixel-based semi-automated supervised maximum likelihood classification. Decadal changes in each class were then quantified using spatial modelling. Flood hazard mapping was performed by assigning weights to factors slope, rainfall distribution, distance from the river and land use/land cover on the basis of their estimated influence in causing flood hazard and performing weighed overlay analysis to identify areas that are highly vulnerable. The forest and grassland coverage increased by 11.53 km² (3.8%) and 1.43 km² (0.47%) from 1996 to 2016. The sediment and bare land areas decreased by 12.45 km² (4.12%) from 1996 to 2016 whereas settlement and cropland areas showed a consistent increase to 14.22 km² (4.7%). Waterbody coverage also increased to 0.3 km² (0.09%) from 1996-2016. 1.27% (3.65 km²) of total watershed area was categorized into very low hazard zone, 20.94% (60.31 km²) area into low hazard zone, 37.59% (108.3 km²) area into moderate hazard zone, 29.25% (84.27 km²) area into high hazard zone and 31 villages which comprised 10.95% (31.55 km²) were categorized into high hazard zone area.Keywords: flood hazard, land use/land cover, Orai river, supervised maximum likelihood classification, weighed overlay analysis
Procedia PDF Downloads 3351105 Critical Parameters of a Square-Well Fluid
Authors: Hamza Javar Magnier, Leslie V. Woodcock
Abstract:
We report extensive molecular dynamics (MD) computational investigations into the thermodynamic description of supercritical properties for a model fluid that is the simplest realistic representation of atoms or molecules. The pair potential is a hard-sphere repulsion of diameter σ with a very short attraction of length λσ. When λ = 1.005 the range is so short that the model atoms are referred to as “adhesive spheres”. Molecular dimers, trimers …etc. up to large clusters, or droplets, of many adhesive-sphere atoms are unambiguously defined. This then defines percolation transitions at the molecular level that bound the existence of gas and liquid phases at supercritical temperatures, and which define the existence of a supercritical mesophase. Both liquid and gas phases are seen to terminate at the loci of percolation transitions, and below a second characteristic temperature (Tc2) are separated by the supercritical mesophase. An analysis of the distribution of clusters in gas, meso- and liquid phases confirms the colloidal nature of this mesophase. The general phase behaviour is compared with both experimental properties of the water-steam supercritical region and also with formally exact cluster theory of Mayer and Mayer. Both are found to be consistent with the present findings that in this system the supercritical mesophase narrows in density with increasing T > Tc and terminates at a higher Tc2 at a confluence of the primary percolation loci. The expended plot of the MD data points in the mesophase of 7 critical and supercritical isotherms in highlight this narrowing in density of the linear-slope region of the mesophase as temperature is increased above the critical. This linearity in the mesophase implies the existence of a linear combination rule between gas and liquid which is an extension of the Lever rule in the subcritical region, and can be used to obtain critical parameters without resorting to experimental data in the two-phase region. Using this combination rule, the calculated critical parameters Tc = 0.2007 and Pc = 0.0278 are found be agree with the values found by of Largo and coworkers. The properties of this supercritical mesophase are shown to be consistent with an alternative description of the phenomenon of critical opalescence seen in the supercritical region of both molecular and colloidal-protein supercritical fluids.Keywords: critical opalescence, supercritical, square-well, percolation transition, critical parameters.
Procedia PDF Downloads 5131104 Influential Parameters in Estimating Soil Properties from Cone Penetrating Test: An Artificial Neural Network Study
Authors: Ahmed G. Mahgoub, Dahlia H. Hafez, Mostafa A. Abu Kiefa
Abstract:
The Cone Penetration Test (CPT) is a common in-situ test which generally investigates a much greater volume of soil more quickly than possible from sampling and laboratory tests. Therefore, it has the potential to realize both cost savings and assessment of soil properties rapidly and continuously. The principle objective of this paper is to demonstrate the feasibility and efficiency of using artificial neural networks (ANNs) to predict the soil angle of internal friction (Φ) and the soil modulus of elasticity (E) from CPT results considering the uncertainties and non-linearities of the soil. In addition, ANNs are used to study the influence of different parameters and recommend which parameters should be included as input parameters to improve the prediction. Neural networks discover relationships in the input data sets through the iterative presentation of the data and intrinsic mapping characteristics of neural topologies. General Regression Neural Network (GRNN) is one of the powerful neural network architectures which is utilized in this study. A large amount of field and experimental data including CPT results, plate load tests, direct shear box, grain size distribution and calculated data of overburden pressure was obtained from a large project in the United Arab Emirates. This data was used for the training and the validation of the neural network. A comparison was made between the obtained results from the ANN's approach, and some common traditional correlations that predict Φ and E from CPT results with respect to the actual results of the collected data. The results show that the ANN is a very powerful tool. Very good agreement was obtained between estimated results from ANN and actual measured results with comparison to other correlations available in the literature. The study recommends some easily available parameters that should be included in the estimation of the soil properties to improve the prediction models. It is shown that the use of friction ration in the estimation of Φ and the use of fines content in the estimation of E considerable improve the prediction models.Keywords: angle of internal friction, cone penetrating test, general regression neural network, soil modulus of elasticity
Procedia PDF Downloads 4101103 How to Break an Outbreak: Containment Measures of a Salmonella Outbreak Associated with Egg Consumption
Authors: Gal Zagron, Nitza Abramson, Deena R. Zimmerman, Chen Stein-Zamir
Abstract:
Background: Salmonella enteritidis is a common cause of foodborne outbreaks, primarily associated with poultry eggs. S. enteritidis This is the only Salmonella type that is found inside the eggshell. A rise in Salmonella enteritidis notifications was noted in spring 2017. Aims: The aim of this study is to describe the epidemiological investigation of the outbreak in the Jerusalem district, along with the containment measures taken. Methods: This study is a population-based epidemiological study with a description of environmental control activities. Results: During the months May - July, 2017 848 salmonellosis cases were reported to the Jerusalem district health office compared to 294 cases May - July 2016. Salmonella enteritidis was isolated in 58% of reported cases. Clusters and outbreaks ( > 2 cases) were reported among nursery schools, nursing homes, persons residing in one kibbutz and several cases in different food service establishments in the Jerusalem district. Epidemiological investigations revealed eggs consumption as a common feature among the cases (uncooked or undercooked eggs in most cases). A national investigation among egg suppliers revealed that most cases consumed eggs provided by a single provider with isolation of Salmonella enteritidis at the source as well. Containment measures were taken to control the epidemic including distributing information via electronic and written media to the public, searching for all egg distribution centers, informing local authorities, the poultry council and food stores. The eggs originating from the provider were recalled and extinguished. Written instructions to all food preparation facilities in the district were distributed regarding the proper storage and preparation of eggs. The number of reported cases declined and the outbreak vanished during correlating months of 2018. Conclusions: The investigation of Salmonella enteritidis outbreaks should include epidemiological and laboratory investigations, tracing the source of the eggs and testing the eggs and the source of eggs. Health education activities are essential as to the proper handling of eggs and egg products aiming to minimize susceptibility to Salmonella infection.Keywords: epidemiological investigation, food-borne disease, food safety, Salmonella enteritidis
Procedia PDF Downloads 1311102 Chikungunya Virus Infection among Patients with Febrile Illness Attending University of Maiduguri Teaching Hospital, Nigeria
Authors: Abdul-Dahiru El-Yuguda, Saka Saheed Baba, Tawa Monilade Adisa, Mustapha Bala Abubakar
Abstract:
Background: Chikungunya (CHIK) virus, a previously anecdotally described arbovirus, is now assuming a worldwide public health burden. The CHIK virus infection is characterized by potentially life threatening and debilitating arthritis in addition to the high fever, arthralgia, myalgia, headache and rash. Method: Three hundred and seventy (370) serum samples were collected from outpatients with febrile illness attending University of Maiduguri Teaching Hospital, Nigeria, and was used to detect for Chikungunya (CHIK) virus IgG and IgM antibodies using the Enzyme Linked Immunosorbent Assays (ELISAs). Result: Out of the 370 sera tested, 39 (10.5%) were positive for presence of CHIK virus antibodies. A total of 24 (6.5%) tested positive for CHIK virus IgM only while none (0.0%) was positive for presence of CHIK virus IgG only and 15 (4.1%) of the serum samples were positive for both IgG and IgM antibodies. A significant difference (p<0.0001) was observed in the distribution of CHIK virus antibodies in relation to gender. The males had prevalence of 8.5% IgM antibodies as against 4.6% observed in females. On the other hand 4.6% of the females were positive for concurrent CHIK virus IgG and IgM antibodies when compared to a prevalence of 3.4% observed in males. Only the age groups ≤ 60 years and the undisclosed age group were positive for presence of CHIK virus IgG and/or IgM antibodies. No significant difference (p>0.05) was observed in the seasonal prevalence of CHIK virus antibodies among the study subjects Analysis of the prevalence of CHIK virus antibodies in relation to clinical presentation (as observed by Clinicians) of the patients revealed that headache and fever were the most frequently encountered ailments. Conclusion: The CHIK virus IgM and concurrent IgM and IgG antibody prevalence rates of 6.5% and 4.1% observed in this study indicates a current infection and the lack of IgG antibody alone observed shows that the infection is not endemic but sporadic. Recommendation: Further studies should be carried to establish the seasonal prevalence of CHIK virus infection vis-à-vis vector dynamics in the study area. A comprehensive study need to be carried out on the molecular characterization of the CHIK virus circulating in Nigeria with a view to developing CHIK virus vaccine.Keywords: Chikungunya virus, IgM and IgG antibodies, febrile patients, enzyme linked immunosorbent assay
Procedia PDF Downloads 3801101 Dose Saving and Image Quality Evaluation for Computed Tomography Head Scanning with Eye Protection
Authors: Yuan-Hao Lee, Chia-Wei Lee, Ming-Fang Lin, Tzu-Huei Wu, Chih-Hsiang Ko, Wing P. Chan
Abstract:
Computed tomography (CT) scan of the head is a good method for investigating cranial lesions. However, radiation-induced oxidative stress can be accumulated in the eyes and promote carcinogenesis and cataract. In this regard, we aimed to protect the eyes with barium sulfate shield(s) during CT scans and investigate the resultant image quality and radiation dose to the eye. Patients who underwent health examinations were selectively enrolled in this study in compliance with the protocol approved by the Ethics Committee of the Joint Institutional Review Board at Taipei Medical University. Participants’ brains were scanned with a water-based marker simultaneously by a multislice CT scanner (SOMATON Definition Flash) under a fixed tube current-time setting or automatic tube current modulation (TCM). The lens dose was measured by Gafchromic films, whose dose response curve was previously fitted using thermoluminescent dosimeters, with or without barium sulfate or bismuth-antimony shield laid above. For the assessment of image quality CT images at slice planes that exhibit the interested regions on the zygomatic, orbital and nasal bones of the head phantom as well as the water-based marker were used for calculating the signal-to-noise and contrast-to-noise ratios. The application of barium sulfate and bismuth-antimony shields decreased 24% and 47% of the lens dose on average, respectively. Under topogram-based TCM, the dose saving power of bismuth-antimony shield was mitigated whereas that of barium sulfate shield was enhanced. On the other hand, the signal-to-noise and contrast-to-noise ratios of DSCT images were decreased separately by barium sulfate and bismuth-antimony shield, resulting in an overall reduction of the CNR. In contrast, the integration of topogram-based TCM elevated signal difference between the ROIs on the zygomatic bones and eyeballs while preferentially decreasing the signal-to-noise ratios upon the use of barium sulfate shield. The results of this study indicate that the balance between eye exposure and image quality can be optimized by combining eye shields with topogram-based TCM on the multislice scanner. Eye shielding could change the photon attenuation characteristics of tissues that are close to the shield. The application of both shields on eye protection hence is not recommended for seeking intraorbital lesions.Keywords: computed tomography, barium sulfate shield, dose saving, image quality
Procedia PDF Downloads 2581100 Exploring the Rhinoceros Beetles of a Tropical Forest of Eastern Himalayas
Authors: Subhankar Kumar Sarkar
Abstract:
Beetles of the subfamily Dynastinae under the family Scarabaeidae of the insect order Coleoptera are popularly known as ‘Rhinoceros beetles’ because of the characteristic horn borne by the males on their head. These horns are dedicated in mating battle against other males and have evolved as a result of phenotypic plasticity. Scarabaeidae is the largest of all families under Coleoptera and is composed of 11 subfamilies, of which the subfamily Dynastinae is represented by approximately 300 species. Some of these beetles have been reported to cause considerable damage to agriculture and forestry both in their larval and adult stages, while many of them are beneficial as they pollinate plants and recycle plant materials. Eastern Himalayas is regarded as one of the 35 biodiversity hotspot zones of the world and one of the four of India, which is exhibited by its rich and megadiverse tropical forests. However, our knowledge on the faunal diversity of these forests is very limited, particularly for the insect fauna. One such tropical forest of Eastern Himalayas is the ‘Buxa Tiger Reserve’ located between latitudes 26°30” to 26°55” North and Longitudes 89°20” to 89˚35” East of India and occupies an area of about 759.26 square kilometers. It is with this background an attempt has been made to explore the insect fauna of the forest. Insect sampling was carried out in each beat and range of Buxa Tiger Reserve in all the three seasons viz, Premonsoon, Monsoon, and Postmonsoon. Sample collections were done by sweep nets, hand picking technique and pit fall traps. UV light trap was used to collect the nocturnal insects. Morphological examinations of the collected samples were carried out with Stereozoom Binocular Microscopes (Zeiss SV6 and SV11) and were identified up to species level with the aid of relevant literature. Survey of the insect fauna of the forest resulted in the recognition of 76 scarab species, of which 8 belong to the subfamily dealt herein. Each of the 8 species represents a separate genus. The forest is dominated by the members of Xylotrupes gideon (Linnaeus) as is represented by highest number of individuals. The recorded taxa show about 12% endemism and are of mainly oriental in distribution. Premonsoon is the most favorable season for their occurrence and activity followed by Monsoon and Postmonsoon.Keywords: Dynastinae, Scarabaeidae, diversity, Buxa Tiger Reserve
Procedia PDF Downloads 1811099 Beneficial Effect of Micropropagation Coupled with Mycorrhization on Enhancement of Growth Performance of Medicinal Plants
Authors: D. H. Tejavathi
Abstract:
Medicinal plants are globally valuable sources of herbal products. Wild populations of many medicinal plants are facing threat of extinction because of their narrow distribution, endemicity, and degradation of specific habitats. Micropropagation is an established in vitro technique by which large number of clones can be obtained from a small bit of explants in a short span of time within a limited space. Mycorrhization can minimize the transient transplantation shock, experienced by the micropropagated plants when they are transferred from lab to land. AM fungal association improves the physiological status of the host plants through better uptake of water and nutrients, particularly phosphorus. Consequently, the growth performance and biosynthesis of active principles are significantly enhanced in AM fungal treated plants. Bacopa monnieri, Andrographis paniculata, Agave vera-curz, Drymaria cordata and Majorana hortensis, important medicinal plants used in various indigenous systems of medicines, are selected for the present study. They form the main constituents of many herbal formulations. Standard in vitro techniques were followed to obtain the micropropagated plants. Shoot tips and nodal segments were used as explants. Explants were cultured on Murashige and Skoog, and Phillips and Collins media supplemented with various combinations of growth regulators. Multiple shoots were obtained on a media containing both auxins and cytokinins at various concentrations and combinations. Multiple shoots were then transferred to rooting media containing auxins for root induction. Thus, obtained in vitro regenerated plants were subjected to brief acclimatization before transferring them to land. One-month-old in vitro plants were treated with AM fungi, and the symbiotic effect on the overall growth parameters was analyzed. It was found that micropropagation coupled with mycorrhization has significant effect on the enhancement of biomass and biosynthesis of active principles in these selected medicinal plants. In vitro techniques coupled with mycorrhization have opened a possibility of obtaining better clones in respect of enhancement of biomass and biosynthesis of active principles. Beneficial effects of AM fungal association with medicinal plants are discussed.Keywords: cultivation, medicinal plants, micropropagation, mycorrhization
Procedia PDF Downloads 1611098 Predicting Child Attachment Style Based on Positive and Safe Parenting Components and Mediating Maternal Attachment Style in Children With ADHD
Authors: Alireza Monzavi Chaleshtari, Maryam Aliakbari
Abstract:
Objective: The aim of this study was to investigate the prediction of child attachment style based on a positive and safe combination parenting method mediated by maternal attachment styles in children with attention deficit hyperactivity disorder. Method: The design of the present study was descriptive of correlation and structural equations and applied in terms of purpose. The population of this study includes all children with attention deficit hyperactivity disorder living in Chaharmahal and Bakhtiari province and their mothers. The sample size of the above study includes 165children with attention deficit hyperactivity disorder in Chaharmahal and Bakhtiari province with their mothers, who were selected by purposive sampling method based on the inclusion criteria. The obtained data were analyzed in two sections of descriptive and inferential statistics. In the descriptive statistics section, statistical indices of mean, standard deviation, frequency distribution table and graph were used. In the inferential section, according to the nature of the hypotheses and objectives of the research, the data were analyzed using Pearson correlation coefficient tests, Bootstrap test and structural equation model. findings:The results of structural equation modeling showed that the research models fit and showed a positive and safe combination parenting style mediated by the mother attachment style has an indirect effect on the child attachment style. Also, a positive and safe combined parenting style has a direct relationship with child attachment style, and She has a mother attachment style. Conclusion:The results and findings of the present study show that there is a significant relationship between positive and safe combination parenting methods and attachment styles of children with attention deficit hyperactivity disorder with maternal attachment style mediation. Therefore, it can be expected that parents using a positive and safe combination232 parenting method can effectively lead to secure attachment in children with attention deficit hyperactivity disorder.Keywords: child attachment style, positive and safe parenting, maternal attachment style, ADHD
Procedia PDF Downloads 551097 Study of Structural Styles and Hydrocarbon Potential of Rajan Pur Area, Middle Indus Basin, Pakistan
Authors: Zakiullah Kalwar, Shabeer Abbassi
Abstract:
This research encompasses the study of structural styles and evaluation of the hydrocarbon potential of Kotrum and Drigri anticlines located in Rajanpur Area, Midddle Indus Basin of Pakistan with the approach of geophysical data integration. The study area is situated between the Sulaiman Foldbelt on the west and Indus River in the east. It is an anticlinal fold, located to the southeast of Sakhi Sarwar anticline and separated from a prominent syncline. The structure has a narrow elongated crest, with the axis running in SSW-NNE direction. In the east, the structure is bounded by a gentle syncline. Structural Styles are trending East-West and perpendicular to tectonic transport and stress direction and the base of the structures gradually dipping Eastward beneath the deformation frontal part in Eastern Sulaiman Fold Belt. Middle Indus Basin can be divided into Foreland, Sulaiman fold belt and a broad foredeep. Sulaiman represents a blind thrust front, which suggests that all frontal folds of the fold belt are cored by blind thrust. The deformation of frontal part of Sulaiman Lobe represents the passive roof duplex stacked beneath the frontal passive roof thrust. The passive roof thrust, which has a back thrust sense of motion and extends into the interior of Fold belt. Left lateral Kingri Fault separates Eastern and Central Sulaiman fold belt. In Central Sulaiman fold belt the deformation front moved further towards fore deep as compared to Eastern Sulaiman. Two wells (Kotrum-01, Drigri-01) have been drilled in the study area with the objective to determine the potential of oil and gas in Habib Rahi Limestone of Eocene age, Dunghan Limestone of Paleocene age and Pab Sandstone of cretaceous age and role of structural styles in hydrocarbon potential of study area. Kotrum-01 well was drilled to its T.D of 4798m. Besides fishing and side tracking, tight whole conditions, high pressure, and losses of circulation were also encountered. During production, testing Pab sandstone were tested but abandoned found. Drigri-01 well was drilled to its T.D 3250 m. RFT was carried out at different points, but all points showed no pressure / seal failure and the well was plugged and declared abandoned.Keywords: hydrocarbon potential, structural style, reserve calculation, enhance production
Procedia PDF Downloads 4231096 Prioritizing Biodiversity Conservation Areas based on the Vulnerability and the Irreplaceability Framework in Mexico
Authors: Alma Mendoza-Ponce, Rogelio Corona-Núñez, Florian Kraxner
Abstract:
Mexico is a megadiverse country and it has nearly halved its natural vegetation in the last century due to agricultural and livestock expansion. Impacts of land use cover change and climate change are unevenly distributed and spatial prioritization to minimize the affectations on biodiversity is crucial. Global and national efforts for prioritizing biodiversity conservation show that ~33% to 45% of Mexico should be protected. The width of these targets makes difficult to lead resources. We use a framework based on vulnerability and irreplaceability to prioritize conservation efforts in Mexico. Vulnerability considered exposure, sensitivity and adaptive capacity under two scenarios (business as usual, BAU based, on the SSP2 and RCP 4.5 and a Green scenario, based on the SSP1 and the RCP 2.6). Exposure to land use is the magnitude of change from natural vegetation to anthropogenic covers while exposure to climate change is the difference between current and future values for both scenarios. Sensitivity was considered as the number of endemic species of terrestrial vertebrates which are critically endangered and endangered. Adaptive capacity is used as the ration between the percentage of converted area (natural to anthropogenic) and the percentage of protected area at municipality level. The results suggest that by 2050, between 11.6 and 13.9% of Mexico show vulnerability ≥ 50%, and by 2070, between 12.0 and 14.8%, in the Green and BAU scenario, respectively. From an ecosystem perspective cloud forests, followed by tropical dry forests, natural grasslands and temperate forests will be the most vulnerable (≥ 50%). Amphibians are the most threatened vertebrates; 62% of the endemic amphibians are critically endangered or endangered while 39%, 12% and 9% of the mammals, birds, and reptiles, respectively. However, the distribution of these amphibians counts for only 3.3% of the country, while mammals, birds, and reptiles in these categories represent 10%, 16% and 29% of Mexico. There are 5 municipalities out of the 2,457 that Mexico has that represent 31% of the most vulnerable areas (70%).These municipalities account for 0.05% of Mexico. This multiscale approach can be used to address resources to conservation targets as ecosystems, municipalities or species considering land use cover change, climate change and biodiversity uniqueness.Keywords: biodiversity, climate change, land use change, Mexico, vulnerability
Procedia PDF Downloads 1581095 The Effectiveness of Prefabricated Vertical Drains for Accelerating Consolidation of Tunis Soft Soil
Authors: Marwa Ben Khalifa, Zeineb Ben Salem, Wissem Frikha
Abstract:
The purpose of the present work is to study the consolidation behavior of highly compressible Tunis soft soil “TSS” by means of prefabricated vertical drains (PVD’s) associated to preloading based on laboratory and field investigations. In the first hand, the field performance of PVD’s on the layer of Tunis soft soil was analysed based on the case study of the construction of embankments of “Radès la Goulette” bridge project. PVD’s Geosynthetics drains types were installed with triangular grid pattern until 10 m depth associated with step-by-step surcharge. The monitoring of the soil settlement during preloading stage for Radès La Goulette Bridge project was provided by an instrumentation composed by various type of tassometer installed in the soil. The distribution of water pressure was monitored through piezocone penetration. In the second hand, a laboratory reduced tests are performed on TSS subjected also to preloading and improved with PVD's Mebradrain 88 (Mb88) type. A specific test apparatus was designed and manufactured to study the consolidation. Two series of consolidation tests were performed on TSS specimens. The first series included consolidation tests for soil improved by one central drain. In thesecond series, a triangular mesh of three geodrains was used. The evolution of degree of consolidation and measured settlements versus time derived from laboratory tests and field data were presented and discussed. The obtained results have shown that PVD’s have considerably accelerated the consolidation of Tunis soft soil by shortening the drainage path. The model with mesh of three drains gives results more comparative to field one. A longer consolidation time is observed for the cell improved by a single central drain. A comparison with theoretical analysis, basically that of Barron (1948) and Carillo (1942), was presented. It’s found that these theories overestimate the degree of consolidation in the presence of PVD.Keywords: tunis soft soil, prefabricated vertical drains, acceleration of consolidation, dissipation of excess pore water pressures, radès bridge project, barron and carillo’s theories
Procedia PDF Downloads 1161094 Development and Characterization of Expandable TPEs Compounds for Footwear Applications
Authors: Ana Elisa Ribeiro Costa, Sónia Daniela Ferreira Miranda, João Pedro De Carvalho Pereira, João Carlos Simões Bernardo
Abstract:
Elastomeric thermoplastics (TPEs) have been widely used in the footwear industry over the years. Recently this industry has been requesting materials that can combine lightweight and high abrasion resistance. Although there are blowing agents on the market to improve the lightweight, when these are incorporated into molten polymers during the extrusion or injection molding, it is necessary to have some specific processing conditions (e.g. effect of temperature and hydrodynamic stresses) to obtain good properties and acceptable surface appearance on the final products. Therefore, it is a great advantage for the compounder industry to acquire compounds that already include the blowing agents. In this way, they can be handled and processed under the same conditions as a conventional raw material. In this work, the expandable TPEs compounds, namely a TPU and a SEBS, with the incorporation of blowing agents, have been developed through a co-rotating modular twin-screw parallel extruder. Different blowing agents such as thermo-expandable microspheres and an azodicarbonamide were selected and different screw configurations and temperature profiles were evaluated since these parameters have a particular influence on the expansion inhibition of the blowing agents. Furthermore, percentages of incorporation were varied in order to investigate their influence on the final product properties. After the extrusion of these compounds, expansion was tested by the injection process. The mechanical and physical properties were characterized by different analytical methods like tensile, flexural and abrasive tests, determination of hardness and density measurement. Also, scanning electron microscopy (SEM) was performed. It was observed that it is possible to incorporate the blowing agents on the TPEs without their expansion on the extrusion process. Only with reprocessing (injection molding) did the expansion of the agents occur. These results are corroborated by SEM micrographs, which show a good distribution of blowing agents in the polymeric matrices. The other experimental results showed a good mechanical performance and its density decrease (30% for SEBS and 35% for TPU). This study suggested that it is possible to develop optimized compounds for footwear applications (e.g., sole shoes), which only will be able to expand during the injection process.Keywords: blowing agents, expandable thermoplastic elastomeric compounds, low density, footwear applications
Procedia PDF Downloads 1901093 Computational Approach to Cyclin-Dependent Kinase 2 Inhibitors Design and Analysis: Merging Quantitative Structure-Activity Relationship, Absorption, Distribution, Metabolism, Excretion, and Toxicity, Molecular Docking, and Molecular Dynamics Simulations
Authors: Mohamed Moussaoui, Mouna Baassi, Soukayna Baammi, Hatim Soufi, Mohammed Salah, Rachid Daoud, Achraf EL Allali, Mohammed Elalaoui Belghiti, Said Belaaouad
Abstract:
The present study aims to investigate the quantitative structure-activity relationship (QSAR) of a series of Thiazole derivatives reported as anticancer agents (hepatocellular carcinoma), using principally the electronic descriptors calculated by the density functional theory (DFT) method and by applying the multiple linear regression method. The developed model showed good statistical parameters (R²= 0.725, R²ₐ𝒹ⱼ= 0.653, MSE = 0.060, R²ₜₑₛₜ= 0.827, Q²𝒸ᵥ = 0.536). The energy of the highest occupied molecular orbital (EHOMO) orbital, electronic energy (TE), shape coefficient (I), number of rotatable bonds (NROT), and index of refraction (n) were revealed to be the main descriptors influencing the anti-cancer activity. Additional Thiazole derivatives were then designed and their activities and pharmacokinetic properties were predicted using the validated QSAR model. These designed molecules underwent evaluation through molecular docking (MD) and molecular dynamic (MD) simulations, with binding affinity calculated using the MMPBSA script according to a 100 ns simulation trajectory. This process aimed to study both their affinity and stability towards Cyclin-Dependent Kinase 2 (CDK2), a target protein for cancer disease treatment. The research concluded by identifying four CDK2 inhibitors - A1, A3, A5, and A6 - displaying satisfactory pharmacokinetic properties. MDs results indicated that the designed compound A5 remained stable in the active center of the CDK2 protein, suggesting its potential as an effective inhibitor for the treatment of hepatocellular carcinoma. The findings of this study could contribute significantly to the development of effective CDK2 inhibitors.Keywords: QSAR, ADMET, Thiazole, anticancer, molecular docking, molecular dynamic simulations, MMPBSA calculation
Procedia PDF Downloads 921092 Spatiotemporal Evaluation of Climate Bulk Materials Production in Atmospheric Aerosol Loading
Authors: Mehri Sadat Alavinasab Ashgezari, Gholam Reza Nabi Bidhendi, Fatemeh Sadat Alavinasab Ashkezari
Abstract:
Atmospheric aerosol loading (AAL) from anthropogenic sources is an evidence in industrial development. The accelerated trends in material consumption at the global scale in recent years demonstrate consumption paradigms sensible to the planetary boundaries (PB). This paper is a statistical approach on recognizing the path of climate-relevant bulk materials production (CBMP) of steel, cement and plastics to AAL via an updated and validated spatiotemporal distribution. The methodology of statistical analysis used the most updated regional or global databases or instrumental technologies. This corresponded to a selection of processes and areas capable for tracking AAL within the last decade, analyzing the most validated data while leading to explore the behavior functions or models. The results also represented a correlation within socio economic metabolism idea between the materials specified as macronutrients of society and AAL as a PB with an unknown threshold. The selected country contributors of China, India, US and the sample country of Iran show comparable cumulative AAL values vs to the bulk materials domestic extraction and production rate in the study period of 2012 to 2022. Generally, there is a tendency towards gradual descend in the worldwide and regional aerosol concentration after 2015. As of our evaluation, a considerable share of human role, equivalent 20% from CBMP, is for the main anthropogenic species of aerosols, including sulfate, black carbon and organic particulate matters too. This study, in an innovative approach, also explores the potential role of AAL control mechanisms from the economy sectors where ordered and smoothing loading trends are accredited through the disordered phenomena of CBMP and aerosol precursor emissions. The equilibrium states envisioned is an approval to the well-established theory of Spin Glasses applicable in physical system like the Earth and here to AAL.Keywords: atmospheric aeroso loading, material flows, climate bulk materials, industrial ecology
Procedia PDF Downloads 671091 Screening of Phytochemicals Compounds from Chasmanthera dependens and Carissa edulis as Potential Inhibitors of Carbonic Anhydrases CA II (3HS4) Receptor using a Target-Based Drug Design
Authors: Owonikoko Abayomi Dele
Abstract:
Epilepsy is an unresolved disease that needs urgent attention. It is a brain disorder that affects over sixty-five (65) million people around the globe. Despite the availability of commercial anti-epileptic drugs, the war against this unmet condition is yet to be resolved. Most epilepsy patients are resistant to available anti-epileptic medications thus the need for affordable novel therapy against epilepsy is a necessity. Numerous phytochemicals have been reported for their potency, efficacy and safety as therapeutic agents against many diseases. This study investigated 99 isolated phytochemicals from Chasmanthera dependens and Carissa edulis against carbonic anhydrase (ii) drug target. The absorption, distribution, metabolism, excretion and toxicity (ADMET) of the isolated compounds were examined using admet SAR-2 web server while Swiss ADME was used to analyze the oral bioavailability, drug-likeness and lead-likeness properties of the selected leads. PASS web server was used to predict the biological activities of selected leads while other important physicochemical properties and interactions of the selected leads with the active site of the target after successful molecular docking simulation with the pyrx virtual screening tool were also examined. The results of these study identified seven lead compounds; C49- alpha-carissanol (-7.6 kcal/mol), C13- Catechin (-7.4 kcal/mol), C45- Salicin (-7.4 kcal/mol), C6- Bisnorargemonine (-7.3 kcal/mol), C36- Pallidine (-7.1 kcal/mol), S4- Lacosamide (-7.1 kcal/mol), and S7- Acetazolamide (-6.4 kcal/mol) for CA II (3HS4 receptor). These leads compounds are probable inhibitors of this drug target due to the observed good binding affinities and favourable interactions with the active site of the drug target, excellent ADMET profiles, PASS Properties, drug-likeness, lead-likeness and oral bioavailability properties. The identified leads have better binding energies as compared to the binding energies of the two standards. Thus, seven identified lead compounds can be developed further towards the development of new anti-epileptic medications.Keywords: drug-likeness, phytochemicals, carbonic anhydrases, metalloeazymes, active site, ADMET
Procedia PDF Downloads 371090 Data-Driven Surrogate Models for Damage Prediction of Steel Liquid Storage Tanks under Seismic Hazard
Authors: Laura Micheli, Majd Hijazi, Mahmoud Faytarouni
Abstract:
The damage reported by oil and gas industrial facilities revealed the utmost vulnerability of steel liquid storage tanks to seismic events. The failure of steel storage tanks may yield devastating and long-lasting consequences on built and natural environments, including the release of hazardous substances, uncontrolled fires, and soil contamination with hazardous materials. It is, therefore, fundamental to reliably predict the damage that steel liquid storage tanks will likely experience under future seismic hazard events. The seismic performance of steel liquid storage tanks is usually assessed using vulnerability curves obtained from the numerical simulation of a tank under different hazard scenarios. However, the computational demand of high-fidelity numerical simulation models, such as finite element models, makes the vulnerability assessment of liquid storage tanks time-consuming and often impractical. As a solution, this paper presents a surrogate model-based strategy for predicting seismic-induced damage in steel liquid storage tanks. In the proposed strategy, the surrogate model is leveraged to reduce the computational demand of time-consuming numerical simulations. To create the data set for training the surrogate model, field damage data from past earthquakes reconnaissance surveys and reports are collected. Features representative of steel liquid storage tank characteristics (e.g., diameter, height, liquid level, yielding stress) and seismic excitation parameters (e.g., peak ground acceleration, magnitude) are extracted from the field damage data. The collected data are then utilized to train a surrogate model that maps the relationship between tank characteristics, seismic hazard parameters, and seismic-induced damage via a data-driven surrogate model. Different types of surrogate algorithms, including naïve Bayes, k-nearest neighbors, decision tree, and random forest, are investigated, and results in terms of accuracy are reported. The model that yields the most accurate predictions is employed to predict future damage as a function of tank characteristics and seismic hazard intensity level. Results show that the proposed approach can be used to estimate the extent of damage in steel liquid storage tanks, where the use of data-driven surrogates represents a viable alternative to computationally expensive numerical simulation models.Keywords: damage prediction , data-driven model, seismic performance, steel liquid storage tanks, surrogate model
Procedia PDF Downloads 1391089 User Expectations and Opinions Related to Campus Wayfinding and Signage Design: A Case Study of Kastamonu University
Authors: Güllü Yakar, Adnan Tepecik
Abstract:
A university campus resembles an independent city that is spread over a wide area. Campuses that incorporate thousands of new domestic and international users at the beginning of every academic period also host scientific, cultural and sportive events, in addition to embodying regular users such as students and staff. Wayfinding and signage systems are necessary for the regulation of vehicular traffic, and they enable users’ to navigate without losing time or feeling anxiety. While designing the system or testing the functionality of it, opinions of existing users or likely behaviors of typical user profiles (personas) provide designers with insight. The purpose of this study is to identify the wayfinding attitudes and expectations of Kastamonu University Kuzeykent Campus users. This study applies a mixed method in which a questionnaire, developed by the researcher, constitute the quantitative phase of the study. The survey was carried out with 850 participants who filled a questionnaire form which was tested in terms of construct validity by using Exploratory Factor Analysis. While interpreting the data obtained, Chi-Square, T- Test and ANOVA analyses were applied as well as descriptive analyses such as frequency (f) and percentage (%) values. The results of this survey, which was conducted during the absence of systematic wayfinding signs in the campus, reveals the participants expectations for insertion of floor plans and wayfinding signs to indoors, maps to outdoors, symbols and color codes to the existing signs and for the adequate arrangement of those for the use of visually impaired people. The fact that there is a direct proportional relation between the length of institution membership and wayfinding competency within campus, leads to the conclusion that especially the new comers are in need of wayfinding signs. In order to determine the effectiveness of campus-wide wayfinding system implemented after the survey and in order to identify the further expectations of users in this respect, a semi-structured interview form developed by the researcher and assessments of 20 participants are compiled. Subjected to content analysis, this data constitute the qualitative dimension of the study. Research results indicate that despite the presence of the signs, the participants experienced either inability or stress while finding their way, showed tendency to receive help from others and needed outdoor maps and signs, in addition to bigger-sized texts.Keywords: environmental graphic design, environmental perception, wayfinding and signage design, wayfinding system
Procedia PDF Downloads 2241088 Challenging the Standard 24 Equal Quarter Tones Theory in Arab Music: A Case Study of Tetrachords Bayyātī and ḤIjāz
Authors: Nabil Shair
Abstract:
Arab music maqām (Arab modal framework) is founded, among other main characteristics, on microtonal intervals. Notwithstanding the importance and multifaceted nature of intonation in Arab music, there is a paucity of studies examining this subject based on scientific and quantitative approaches. The present-day theory concerning the Arab tone system is largely based on the pioneering treatise of Mīkhā’īl Mashāqah (1840), which proposes the theoretical division of the octave into 24 equal quarter tones. This kind of equal-tempered division is incompatible with the performance practice of Arab music, as many professional Arab musicians conceptualize additional pitches beyond the standard 24 notes per octave. In this paper, we refute the standard theory presenting the scale of well-tempered quarter tones by implementing a quantitative analysis of the performed intonation of two prominent tetrachords in Arab music, namely bayyātī and ḥijāz. This analysis was conducted with the help of advanced computer programs, such as Sonic Visualiser and Tony, by which we were able to obtain precise frequency data (Hz) of each tone every 0.01 second. As a result, the value (in cents) of all three intervals of each tetrachord was measured and accordingly compared to the theoretical intervals. As a result, a specific distribution of a range of deviation from the equal-tempered division of the octave was detected, especially the detection of a diminished first interval of bayyātí and diminished second interval of ḥijāz. These types of intonation entail a considerable amount of flexibility, mainly influenced by surrounding tones, direction and function of the measured tone, ornaments, text, personal style of the performer and interaction with the audience. This paper seeks to contribute to the existing literature dealing with intonation in Arab music, as it is a vital part of the performance practice of this musical tradition. In addition, the insights offered by this paper and its novel methodology might also contribute to the broadening of the existing pedagogic methods used to teach Arab music.Keywords: Arab music, intonation, performance practice, music theory, oral music, octave division, tetrachords, music of the middle east, music history, musical intervals
Procedia PDF Downloads 451087 The Instrumentalization of Digital Media in the Context of Sexualized Violence
Authors: Katharina Kargel, Frederic Vobbe
Abstract:
Sexual online grooming is generally defined as digital interactions for the purpose of sexual exploitation of children or minors, i.e. as a process for preparing and framing sexual child abuse. Due to its conceptual history, sexual online grooming is often associated with perpetrators who are previously unknown to those affected. While the strategies of perpetrators and the perception of those affected are increasingly being investigated, the instrumentalisation of digital media has not yet been researched much. Therefore, the present paper aims at contributing to this research gap by examining in what kind of ways perpetrators instrumentalise digital media. Our analyses draw on 46 case documentations and 18 interviews with those affected. The cases and the partly narrative interviews were collected by ten cooperating specialist centers working on sexualized violence in childhood and youth. For this purpose, we designed a documentation grid allowing for a detailed case reconstruction i.e. including information on the violence, digital media use and those affected. By using Reflexive Grounded Theory, our analyses emphasize a) the subjective benchmark of professional practitioners as well as those affected and b) the interpretative implications resulting from our researchers’ subjective and emotional interaction with the data material. It should first be noted that sexualized online grooming can result in both online and offline sexualized violence as well as hybrid forms. Furthermore, the perpetrators either come from the immediate social environment of those affected or are unknown to them. The perpetrator-victim relationship plays a more important role with regard to the question of the instrumentalisation of digital media than the question of the space (on vs. off) in which the primary violence is committed. Perpetrators unknown to those affected instrumentalise digital media primarily to establish a sexualized system of norms, which is usually embedded in a supposed love relationship. In some cases, after an initial exchange of sexualized images or video recordings, a latent play on the position of power takes place. In the course of the grooming process, perpetrators from the immediate social environment increasingly instrumentalise digital media to establish an explicit relationship of power and dependence, which is directly determined by coercion, threats and blackmail. The knowledge of possible vulnerabilities is strategically used in the course of maintaining contact. The above explanations lead to the conclusion that the motive for the crime plays an essential role in the question of the instrumentalisation of digital media. It is therefore not surprising that it is mostly the near-field perpetrators without commercial motives who initiate a spiral of violence and stress by digitally distributing sexualized (violent) images and video recordings within the reference system of those affected.Keywords: sexualized violence, children and youth, grooming, offender strategies, digital media
Procedia PDF Downloads 176