Search results for: experimental culture

Authors: V. Lokesh, M. Manjunathan, S. Sairam, K. Saithsh Kumar, R. Anantharaj

Abstract:

The densities of pure and its binary mixtures of 1-Butyl-3-methyl imidazolium bis (trifluoro methyl sulfonyl) imide and 1–Ethyl-3-methyl imidazolium ethyl sulphate at different temperature, over the entire composition range were measured at 293.15, 298.15, 303.15, 308.15, 313.15, 318.15, 323.15, 328.15, 33.15, 338.15, 343.15 K. In this study, the liquid-liquid extraction procedure was used. From this experimental data, the excess molar volumes, apparent molar volume, partial molar volumes and the excess partial molar volumes have been calculated for over the whole composition range. Hence, the effect of temperature and composition on all derived thermodynamic properties of this binary mixture will be discussed in terms of intermolecular interactions.

Keywords: ionic liquid, interaction energy, effect of temperature, effect of composition

Procedia PDF Downloads 158

Authors: Benmalek M. Larbi, R. Harbi, S. Boukor

Abstract:

This paper reports an experimental work that aimed to investigate the effects of clay brick waste, as part of fine aggregate, on rendering mortar performance. The brick, in crushed form, was from a local brick manufacturer that was rejected due to being of-standard. It was used to replace 33.33 %, 50 %, 66.66 % and 100 % by weight of the quarry sand in mortar. Effects of the brick replacement on the mortar key properties intended for wall plastering were investigated; these are workability, compressive strength, flexural strength, linear shrinkage, water absorption by total immersion and by capillary suction. The results showed that as the brick replacement level increased, the mortar workability reduced. The linear shrinkage increases over time and decreases with the introduction of brick waste. The compressive and flexural strengths decrease with the increase of brick waste because of their great water absorption.

Keywords: clay brick waste, mortar, properties, quarry sand

Procedia PDF Downloads 239

Authors: Ayesha Khatun

Abstract:

In 21st century where markets are unstable, technologies rapidly proliferate, competitors multiply, products and services become obsolete almost overnight and customers demand low cost high value product, leveraging and harnessing knowledge is not just a potential source of competitive advantage rather a necessity in technology based and information intensive industries. Knowledge management focuses on leveraging the available knowledge and sharing the same among the individuals in the organization so that the employees can make best use of it towards achieving the organizational goals. Knowledge is not a discrete object. It is embedded in people and so difficult to transfer outside the immediate context that it becomes a major competitive advantage. However, internal transfer of knowledge among the employees is essential to maximize the use of knowledge available in the organization in an unstructured manner. But as knowledge is the source of competitive advantage for the organization it is also the source of competitive advantage for the individuals. People think that knowledge is power and sharing the same may lead to lose the competitive position. Moreover, the very nature of tacit knowledge poses many difficulties in sharing the same. But sharing tacit knowledge is the vital part of knowledge management process because it is the tacit knowledge which is inimitable. Knowledge management has been made synonymous with the use of software and technology leading to the management of explicit knowledge only ignoring personal interaction and forming of informal networks which are considered as the most successful means of sharing tacit knowledge. Factors responsible for effective sharing of tacit knowledge are grouped into –individual, organizational and technological factors. Different factors under each category have been identified. Creating a positive organizational culture, encouraging personal interaction, practicing reward system are some of the strategies that can help to overcome many of the barriers to effective sharing of tacit knowledge. Methodology applied here is completely secondary. Extensive review of relevant literature has been undertaken for the purpose.

Keywords: knowledge, tacit knowledge, knowledge management, sustainable competitive advantage, organization, knowledge sharing

Procedia PDF Downloads 384

Authors: L. Foudia, K. Haddadi, M. Reffas

Abstract:

First principles study of structural, elastic, electronic and optical properties of the monoclinic perovskite type ScRhO₃ has been reported using the pseudo-potential plane wave method within the local density approximation. The calculated lattice parameters, including the lattice constants and angle β are in excellent agreement with the available experimental data, which proving the reliability of the chosen theoretical approach. Pressure dependence up to 20 GPa of the single crystal and polycrystalline elastic constants has been investigated in details using the strain-stress approach. The mechanical stability, ductility, average elastic wave velocity, Debye temperature and elastic anisotropy were also assessed. Electronic band structure and density of states (DOS) demonstrated its semiconducting nature showing a direct band gap of 1.38 eV. Furthermore, several optical properties, such as absorption coefficient, reflectivity, refractive index, dielectric function, optical conductivity and electron energy loss function have been calculated for radiation up to 40 eV.

Keywords: ab-initio, perovskite, DFT, band gap.

Procedia PDF Downloads 56

Authors: Vadivel Ayyasamy

Abstract:

The present approach deals with the identification of Emotions and classification of Emotional patterns at Phrase-level with respect to Positive and Negative Orientation. The proposed approach considers emotion triggered terms, its co-occurrence terms and also associated sentences for recognizing emotions. The proposed approach uses Part of Speech Tagging and Emotion Actifiers for classification. Here sentence patterns are broken into phrases and Neuro-Fuzzy model is used to classify which results in 16 patterns of emotional phrases. Suitable intensities are assigned for capturing the degree of emotion contents that exist in semantics of patterns. These emotional phrases are assigned weights which supports in deciding the Positive and Negative Orientation of emotions. The approach uses web documents for experimental purpose and the proposed classification approach performs well and achieves good F-Scores.

Keywords: emotions, sentences, phrases, classification, patterns, fuzzy, positive orientation, negative orientation

Procedia PDF Downloads 362

Authors: Z. Abram, V. Nadasan, J. Balint, J. L. Ferencz

Abstract:

Introduction: Online smoking prevention programs became popular in the last time. In order to extend the use of such programs, existing applications can be adapted and translated in the native languages of the target groups. It is the first time that in Romania such a software was implemented. Our goal was to provide a computer-aided intervention with attractive content targeting high school students who are familiar with information and communication technology. Material and methods: ASPIRA is the Romanian/Hungarian adapted version of a smoking prevention program created in USA. Prior to apply the questionnaire and ASPIRA online program which contains five modules that include tests, videos and interactive games, the program was tested in some IT laboratories on a group of schoolchildren and students. The pilot study questionnaires were completed considering the opinions of young people and the functionality of the software. Results: Above 90% of participants reported a good or very good impression about the ASPIRA program. Only a small minority found that the program included some parts which were too long or reported the existence of any technical problems regarding the functionality of the software. 76% of the participants had little or very little difficulty in understanding the messages presented by the English speaking characters. Only 7.5% of the participants thought that the program included content that was not appropriate for the local culture. Conclusions: The vast majority of students reported favorite impressions about ASPIRA online program. High school students and boys were more critical. Language and cultural barriers did not have the potential to reduce in a significant manner the effectiveness of the tested program.

Keywords: smoking prevention, ASPIRA online program, youth opinions, language/cultural barriers

Procedia PDF Downloads 253

Authors: Yunus Doğan, Ahmet Durap

Abstract:

Coastal regions are the one of the most commonly used places by the natural balance and the growing population. In coastal engineering, the most valuable data is wave behaviors. The amount of this data becomes very big because of observations that take place for periods of hours, days and months. In this study, some statistical methods such as the wave spectrum analysis methods and the standard statistical methods have been used. The goal of this study is the discovery profiles of the different coast areas by using these statistical methods, and thus, obtaining an instance based data set from the big data to analysis by using data mining algorithms. In the experimental studies, the six sample data sets about the wave behaviors obtained by 20 minutes of observations from Mersin Bay in Turkey and converted to an instance based form, while different clustering techniques in data mining algorithms were used to discover similar coastal places. Moreover, this study discusses that this summarization approach can be used in other branches collecting big data such as medicine.

Keywords: clustering algorithms, coastal engineering, data mining, data summarization, statistical methods

Procedia PDF Downloads 348

Authors: Tang Mui Joo, Chan Eang Teng

Abstract:

The use of social media has become more defined. It has been widely used for the purpose of business. More marketers are now using social media as tools to enhance their businesses. Whereas on the other hand, there are more and more people spending their time through mobile apps to be engaged in the social media sites like YouTube, Facebook, Twitter and others. Social media has even become common in Public Relations (PR). It has become number one platform for creating and sharing content. In view to this, social media has changed the rules in PR where it brings new challenges and opportunities to the profession. Although corporate websites, chat-rooms, email customer response facilities and electronic news release distribution are now viewed as standard aspects of PR practice, many PR practitioners are still struggling with the impact of new media though the implementation of social media is potentially reducing the cost of communication. It is to the point that PR practitioners are not fully embracing new media, they are ill-equipped to do so and they have a fear of the technology. Somehow that social media has become a new style of communication that is characterized by conversation and community. It has become a platform that allows individuals to interact with one another and build relationship among each other. Therefore, in the use of business world, consumers are able to interact with those companies that have joined any social media. Based on their experiences with social networking site interactions, they are also exposed to personal interaction while communicating. This paper is to study the impact of social media to PR. This paper discovers the potential changes of PR practices in a developing country like Malaysia. Eventually the study reflects on how PR practitioners are actually using social media in the country. This paper is based on two theories in its development of this research foundation. Media Ecology Theory is to support the impact and changes to PR. Social Penetration Theory is to reflect on how the use of social media is among PRs. This research is using survey with PR practitioners in its data collection. The results have shown that PR professionals value social media more than they actually use it and the way of organizations communicate had been changed due to the transformation of social media.

Keywords: new media, social media, PR, change of trend, communication, digital culture

Procedia PDF Downloads 303

Authors: Saulutė Juzelėnienė, Skirmantė Šarkauskienė

Abstract:

In this paper, it is aimed to analyse the multimodal representations of the concepts of LOVE and PASSION in Lithuanian graphic novel “Gertrūda”, by Gerda Jord. The research is based on the earlier findings by Forceville (2005), Eerden (2009) as well as insights made by Shihara and Matsunaka (2009) and Kövecses (2000). The domains of target and source of LOVE and PASSION metaphors in comics are expressed by verbal and non-verbal cues. The analysis of non-verbal cues adopts the concepts of rune and indexes. A pictorial rune is a graphic representation of an object that does not exist in reality in comics, such as lines, dashes, text "balloons", and pictorial index – a graphically represented object of reality, a real symptom expressing a certain emotion, such as a wide smile, furrowed eyebrows, etc. Indexes are often hyperbolized in comics. The research revealed that most frequent source domains are CLOSINESS/UNITY, NATURAL/ PHYSICAL FORCE, VALUABLE OBJECT, PRESSURE. The target is the emotion of LOVE/PASSION which belongs to a more abstract domain of psychological experience. In this kind of metaphor, the picture can be interpreted as representing the emotion of happiness. Data are taken from Lithuanian comic books and Internet sites, where comics have been presented. The data and the analysis we are providing in this article aims to reveal that there are pictorial metaphors that manifest conceptual metaphors that are also expressed verbally and that methodological framework constructed for the analysis in the papers by Forceville at all is applicable to other emotions and culture specific pictorial manifestations.

Keywords: multimodal metaphor, conceptual metaphor, comics, graphic novel, concept of love/passion

Procedia PDF Downloads 54

Authors: Sana Ridene, Soumaya Sayeb, Houda Helali, Mohammed Ben Hassen

Abstract:

Nonwoven structures have a range of applications which include Medical, filtration, geotextile and recently this unconventional fabric is finding a niche in fashion apparel. In this paper, a modified form of Vangheluwe rheological model is used to describe the mechanical behavior of nonwovens fabrics in uniaxial tension. This model is an association in parallel of three Maxwell elements characterized by damping coefficients η1, η2 and η3 and E1, E2, E3 elastic modulus and a nonlinear spring C. The model is verified experimentally with two types of nonwovens (50% viscose /50% Polyester) and (40% viscose/60% Polyester) and a range of three square weights values. Comparative analysis of the theoretical model and the experimental results of tensile test proofs a high correlation between them. The proposed model can fairly well replicate the behavior of nonwoven fabrics during relaxation and sample traction. This allowed us to predict the mechanical behavior in tension and relaxation of fabrics starting only from their technical parameters (composition and weight).

Keywords: mechanical behavior, tensile strength, relaxation, rheological model

Procedia PDF Downloads 391

Authors: Masato Nishi, Tetsushi Kaburagi, Masashi Kurose, Tei Hirashima, Tetsusei Kurasiki

Abstract:

The process of thermoforming a carbon fiber reinforced thermoplastic (CFRTP) has increased its presence in the automotive industry for its wide applicability to the mass production car. A non-isothermal forming for CFRTP can shorten its cycle time to less than 1 minute. In this paper, the textile reinforcement FE model which the authors proposed in a previous work is extended to the CFRTP model for non-isothermal forming simulation. The effect of thermoplastic is given by adding shell elements which consider thermal effect to the textile reinforcement model. By applying Reuss model to the stress calculation of thermoplastic, the proposed model can accurately predict in-plane shear behavior, which is the key deformation mode during forming, in the range of the process temperature. Using the proposed model, thermoforming simulation was conducted and the results are in good agreement with the experimental results.

Keywords: carbon fiber reinforced thermoplastic, finite element analysis, pre-impregnated textile composite, non-isothermal forming

Procedia PDF Downloads 414

Authors: Diobein C. Flores

Abstract:

The populace in Municipality of Talaingod is composed of Ata-Manobo. The said lumads enrich their culture, orientation and self because the place is a hive of their tribe. In lieu, the study would analyze the participation of the Ata-Manobo in the making of school improvement plan (SIP). Thus, it recommends alternative policy options that would help strengthen their involvement. The school stakeholders-Ata Manobo representatives from students, parent-teacher association, alumni, basic sector, municipal/barangay government unit, civic/social organizations and other government various agencies are the key participants in this study. The research used descriptive design. The responses of the representatives were analyzed through the criteria involved in employing Rational Model. The technical dimension, administrative, political acceptability and economic are the criteria in revealing decision. The policy alternative option 3- recommends to formulate policy for the purpose of capacitating stakeholders or governing council members in the making of SIP was pointed out as the most preferred option. This could strengthen the participation among Ata-Manobo as stakeholders in planning. Hence, the formulation alternative policy- capacitating stakeholders in the crafting of school improvement plan is recommended. The suggested initiative would assist the Department of Education in forging consensus across neighborhoods during the making of SIP. The appropriation of the definite budget to be used during the conduct of capability building activities is also suggested. Training-workshops are identified as possible intervention to ensure that the stakeholders are equipped with necessary knowledge and skills needed in the making of SIP. Indeed, the equal opportunities for all stakeholders regardless of their life circumstances must be noted. With the belief, people must be empowered to take advantage and spearhead progress in the making of SIP.

Keywords: Ata-Manobo Tribe, stakeholders, school improvement plan, Municipality of Talaingod, Philippines

Procedia PDF Downloads 311

Authors: Mohammad Ali Badri, Pouya Molana, Amin Rezvanpour

Abstract:

In this paper, planning catamaran and mono-hull vessels resistance and trim in calm waters were considered. Hydrodynamic analysis of fast mono-hull planning vessel was also investigated. In order to hull form geometry optimization, numerical methods of different parameters were used for this type of vessels. Hull material was selected in carbon fiber composite. Exact architectural aspects were specified and stability calculations were performed as well. Hydrodynamic calculations to extract the resistance force using semi-analytical methods and numerical modeling were carried out. Free surface numerical analysis of vessel in designed draft using finite volume method and double phase were evaluated and verified by experimental tests.

Keywords: fast vessel, hydrostatic and hydrodynamic optimization, free surface flow, computational fluid dynamics

Procedia PDF Downloads 502

Authors: Surapol Raadnui

Abstract:

This particular work describes an experimental investigation on gear wear in which wear and pitting were intentionally allowed to occur, namely, moisture corrosion pitting, acid-induced corrosion pitting, hard contaminant-related pitting and mechanical induced wear. A back to back spur gear test rig and a grease lubricated worm gear rig were used. The tests samples of wear debris were collected and assessed through the utilization of an optical microscope in order to correlate and compare the debris morphology to pitting and wear degradation of the worn gears. In addition, weight loss from all test gear pairs were assessed with utilization of statistical design of experiment. It can be deduced that wear debris characteristics from both cases exhibited a direct relationship with different pitting and wear modes. Thus, it should be possible to detect and diagnose gear pitting and wear utilization of worn surfaces, generated wear debris and quantitative measurement such as weight loss.

Keywords: predictive maintenance, worm gear, spur gear, wear debris analysis, problem diagnostic

Procedia PDF Downloads 136

Authors: Hsiao-Chuan Huang, King-Lung Kuo, Mei-Hsin Lo, Hsiao-Yun Chou, Yusen Lin

Abstract:

The most robust and economical method for laboratory diagnosis of TB is to identify mycobacterial bacilli (AFB) under acid-fast staining despite its disadvantages of low sensitivity and labor-intensive. Though digital pathology becomes popular in medicine, an automated microscopic system for microbiology is still not available. A new AI-assisted automated microscopic system, consisting of a microscopic scanner and recognition program powered by big data and deep learning, may significantly increase the sensitivity of TB smear microscopy. Thus, the objective is to evaluate such an automatic system for the identification of AFB. A total of 5,930 smears was enrolled for this study. An intelligent microscope system (TB-Scan, Wellgen Medical, Taiwan) was used for microscopic image scanning and AFB detection. 272 AFB smears were used for transfer learning to increase the accuracy. Referee medical technicians were used as Gold Standard for result discrepancy. Results showed that, under a total of 1726 AFB smears, the automated system's accuracy, sensitivity and specificity were 95.6% (1,650/1,726), 87.7% (57/65), and 95.9% (1,593/1,661), respectively. Compared to culture, the sensitivity for human technicians was only 33.8% (38/142); however, the automated system can achieve 74.6% (106/142), which is significantly higher than human technicians, and this is the first of such an automated microscope system for TB smear testing in a controlled trial. This automated system could achieve higher TB smear sensitivity and laboratory efficiency and may complement molecular methods (eg. GeneXpert) to reduce the total cost for TB control. Furthermore, such an automated system is capable of remote access by the internet and can be deployed in the area with limited medical resources.

Keywords: TB smears, automated microscope, artificial intelligence, medical imaging

Procedia PDF Downloads 205

Authors: Sadegh Torfi

Abstract:

Realization of anticipated energy efficiency from recuperative run-around energy recovery (RER) systems requires identification of the system components influential parameters. Because simulation modeling is considered as an integral part of the design and economic evaluation of RER systems, it is essential to calibrate the developed models and validate the performance predictions by means of comparison with data from experimental measurements. Several theoretical and numerical analyses on RER systems by researchers have been done, but generally the effect of distance between hot and cold flow is ignored. The objective of this study is to develop a thermohydroulic model for a typical RER system that accounts for energy loss from the interconnecting piping and effects of interconnecting pipes length performance of run-around energy recovery systems. Numerical simulation shows that energy loss from the interconnecting piping is change linear with pipes length and if pipes are properly isolated, maximum reduction of effectiveness of RER systems is 2% in typical piping systems.

Keywords: combined heat and power, heat recovery, effectiveness, CGS

Procedia PDF Downloads 187

Authors: M. Guen

Abstract:

A three-dimensional numerical study is used to analyze the behavior of the flow inside a vortex tube. The vortex tube or Ranque-Hilsch vortex tube is a simple device which is capable of dividing compressed air from the inlet nozzle tangentially into two flow with different temperatures warm and cold. This phenomenon is known from literature by temperature separation. The K ω-SST and K-ε turbulence models are used to predict the turbulent flow behaviour inside the tube. The vortex tube is an Exair 708 slpm (25 scfm) commercial tube. The cold and hot exits areas are 30.2 and 95 mm2 respectively. The vortex nozzle consists of 6 straight slots; the height and the width of each slot are 0.97 mm and 1.41 mm. The total area normal to the flow associated with six nozzles is therefore 8.15 mm 2. The present study focuses on a comparison between two turbulence models K ω-SST, K-ε by using a new configuration of vortex tube (Conical Vortex Tube). The performance curves of the temperature separation versus cold outlet mass fraction were calculated and compared with experimental and numerical study of other researchers.

Keywords: conical vortex tube, temperature separation, cold mass fraction, turbulence

Procedia PDF Downloads 238

Authors: Zhoucheng Bao, Haiyan Zhu, Tingting Pang, Zuling Wang

Abstract:

This paper proposes a multi-population DE with adaptive mutation and local search for global optimization, named AMMADE. In order to better coordinate the cooperation between the populations and the rational use of resources. In AMMADE, the population is divided based on the Euclidean distance sorting method at each generation to appropriately coordinate the cooperation between subpopulations and the usage of resources, such that the best-performed subpopulation will get more computing resources in the next generation. Further, an adaptive local search strategy is employed on the best-performed subpopulation to achieve a balanced search. The proposed algorithm has been tested by solving optimization problems taken from CEC2014 benchmark problems. Experimental results show that our algorithm can achieve a competitive or better than related methods. The results also confirm the significance of devised strategies in the proposed algorithm.

Keywords: differential evolution, multi-mutation strategies, memetic algorithm, adaptive local search

Procedia PDF Downloads 135

Authors: R. K. Vinnakota, D. A. Genov, Z. Dong, A. F. Briggs, L. Nordin, S. R. Bank, D. Wasserman

Abstract:

We present a semiconductor-based plasmonic electro-optic modulator based on excitation and active control of surface plasmon polaritons (SPPs) at the interface of degenerately doped In₀.₅₃Ga₀.₄₇As pn++ junctions. Set of devices, which we refer to as a surface plasmon polariton diode (SPPD), are fabricated and characterized electrically and optically. Optical characterization predicts far-field voltage-aided reflectivity modulation for mid-IR wavelengths. Numerical device characterizations using a self-consistent electro-optic multiphysics model have been performed to confirm the experimental findings were predicting data rates up to 1Gbits/s and 3dB bandwidth as high as 2GHz. Our findings also show that decreasing the device dimensions can potentially lead to data rates of more than 50Gbits/s, thus potentially providing a pathway toward fast all-semiconductor-based plasmotronic devices.

Keywords: plasmonics, optoelectronics, PN junctions, surface plasmon polaritons

Procedia PDF Downloads 98

Authors: Lara Stroh, Nikola Horová, Robert Stárek, Ittoop V. Puthoor, Michal Mičuda, Miloslav Dušek, Erika Andersson

Abstract:

Oblivious transfer (OT) is an important cryptographic primitive. Any multi-party computation can be realised with OT as a building block. XOR oblivious transfer (XOT) is a variant where the sender Alice has two bits, and a receiver, Bob, obtains either the first bit, the second bit, or their XOR. Bob should not learn anything more than this, and Alice should not learn what Bob has learned. Perfect quantum OT with information-theoretic security is known to be impossible. We determine the smallest possible cheating probabilities for unrestricted dishonest parties in non-interactive quantum XOT protocols using symmetric pure states and present an optimal protocol which outperforms classical protocols. We also "reverse" this protocol so that Bob becomes the sender of a quantum state and Alice the receiver who measures it while still implementing oblivious transfer from Alice to Bob. Cheating probabilities for both parties stay the same as for the unreversed protocol. We optically implemented both the unreversed and the reversed protocols and cheating strategies, noting that the reversed protocol is easier to implement.

Keywords: oblivious transfer, quantum protocol, cryptography, XOR

Procedia PDF Downloads 102

Authors: Dolores Hidalgo, Jesús M. Martín-Marroquín, Francisco Corona

Abstract:

Municipal waste consist of a variety of items that are everyday discarded by the population. They are usually collected by municipalities and include waste generated by households, commercial activities (local shops) and public buildings. The composition of municipal waste varies greatly from place to place, being mostly related to levels and patterns of consumption, rates of urbanization, lifestyles, and local or national waste management practices. Each year, a huge amount of resources is consumed in the EU, and according to that, also a huge amount of waste is produced. The environmental problems derived from the management and processing of these waste streams are well known, and include impacts on land, water and air. The situation in remote areas is even worst. Difficult access when climatic conditions are adverse, remoteness of centralized municipal treatment systems or dispersion of the population, are all factors that make remote areas a real municipal waste treatment challenge. Furthermore, the scope of the problem increases significantly because the total lack of awareness of the existing risks in this area together with the poor implementation of advanced culture on waste minimization and recycling responsibly. The aim of this work is to analyze the existing situation in remote areas in reference to the production of municipal waste and evaluate the efficiency of different management alternatives. Ideas for improving waste management in remote areas include, for example: the implementation of self-management systems for the organic fraction; establish door-to-door collection models; promote small-scale treatment facilities or adjust the rates of waste generation thereof.

Keywords: door to door collection, islands, isolated areas, municipal waste, remote areas, rural communities

Procedia PDF Downloads 245

Authors: Armin Najipour, A. M. Fattahi

Abstract:

The aim of this research was to investigate the effect of the addition of multi walled carbon nanotubes on the mechanical properties of polyethylene/carbon nanotube nanocomposites. To do so, polyethylene and carbon nanotube were mixed in different weight percentages containing 0, 0.5, 1, and 1.5% carbon nanotube in two screw extruder apparatus by fusion. Then the nanocomposite samples were molded in injection apparatus according to ASTM: D6110 standard. The effects of carbon nanotube addition in 4 different levels and injection pressure in 2 levels on the hardness and impact strength of the nanocomposite samples were investigated. The results showed that the addition of carbon nanotube had a significant effect on improving hardness and impact strength of the nanocomposite samples such that by adding 1% w/w carbon nanotube, the impact strength and hardness of the samples improved to 74% and 46.7% respectively. Also, according to the results, the effect of injection pressure on the results was much less than that of carbon nanotube weight percentage.

Keywords: carbon nanotube, injection molding, mechanical properties, nanocomposite, polyethylene

Procedia PDF Downloads 304

Authors: Abderrezzak khatib

Abstract:

Biogenic amines are low molecular weight nitrogenous compounds that have the potential to accumulate in food, posing a significant risk to food safety and human health. In this study, we investigated the inhibitory activity of three strains of lactic acid bacteria (LAB), against the growth and production of biogenic amines by both foodborne pathogens and food spoilage bacteria. The foodborne pathogens studied included Staphylococcus aureus, Pseudomonas aeruginosa, and Salmonella Paratyphi, while the food spoilage bacteria comprised Enterobacter cloacae and Proteus mirabilis. The methodology involved bacterial growth determination in petri dishes, bacterial culture extraction and derivatization, and biogenic amine analysis using HPLC. Our findings revealed that the inhibitory effects of LAB on these pathogens varied, with all three LAB strains demonstrating a remarkable reduction in the total bacterial count when combined with most pathogens, compared to the individual cultures of the pathogens. Furthermore, the presence of LAB in co-cultures with the pathogens resulted in a significant decrease in the production of tyramine and other biogenic amines by the pathogens themselves. These results suggest that LAB strains hold considerable promise in preventing the accumulation of biogenic amines in food products, thereby enhancing food safety. This study provides insights into the potential utilization of LAB in the context of preserving and ensuring the safety of food products. It highlights the significance of conducting additional research endeavors to elucidate the underlying mechanisms involved and to identify the precise bioactive compounds that are responsible for the observed inhibitory effects.

Keywords: food safety, lactic acid bacteria, foodborne pathogens, food spoilage bacteria, biogenic amines, tyrosine

Procedia PDF Downloads 41

Authors: M. Khalfa, H. Khachai, F. Chiker, K. Bougherara, R. Khenata, G. Murtaza, M. Harmel

Abstract:

A theoretical study of structural, elastic, electronic and thermodynamic properties of Fe2VX, (with X = Al and Ga), were studied by means of the full-relativistic version of the full-potential augmented plane wave plus local orbitals method. For exchange and correlation potential we used both generalized-gradient approximation (GGA) and local-density approximation (LDA). Our calculated ground state properties like as lattice constants, bulk modulus and elastic constants appear more accurate when we employed the GGA rather than the LDA approximation, and these results agree very well with the available experimental and theoretical data. Further, prediction of the thermal effects on some macroscopic properties of Fe2VAl and Fe2VGa are given in this paper using the quasi-harmonic Debye model in which the lattice vibrations are taken into account. We have obtained successfully the variations of the primitive cell volume, volume expansion coefficient, heat capacities and Debye temperature with pressure and temperature in the ranges of 0–40 GPa and 0–1500 K.

Keywords: full Heusler, FP-LAPW, electronic properties, thermal properties

Procedia PDF Downloads 476

Authors: Otman Jai, Otman Elhajjaji, Jaouad Tajmouati

Abstract:

Several neutronic calculation codes must be used to solve the equation for different levels of discretization which all necessitate a specific modelisation. This chain of such models, known as a calculation scheme, leads to the knowledge of the neutron flux in a reactor from its own geometry, its isotopic compositions and a cross-section library. Being small in size, the 'Slowpoke-2' reactor is difficult to model due to the importance of the leaking neutrons. In the paper, the simulation model is presented (geometry, cross section library, assumption, etc.), and the results obtained by DRAGON4/DONJON4 codes were compared to the calculations performed with Monte Carlo code MCNP using detailed geometrical model of the reactor and the experimental data. Criticality calculations have been performed to verify and validate the model. Since created model properly describes the reactor core, it can be used for calculations of reactor core parameters and for optimization of research reactor application.

Keywords: transport equation, Dragon4, Donjon4, neutron flux, effective multiplication factor

Procedia PDF Downloads 453

Authors: Eglė Žurauskaitė, Eglė Gudavičienė

Abstract:

The goal of this paper is to reveal how polarization is constructed through the use of impoliteness strategies. In general, media helps to spread various ideas very fast, and it means that processes of polarization are best revealed in computer-mediated communication (CMC) contexts. For this reason, data for the research was collected from online texts about a current, very diverse topic in Lithuania - Lithuanian language policy and regulations, because this topic is causing a lot of tension in Lithuanian society. Computer-mediated communication allows users to edit their message before they send it. It means that addressees carefully select verbal expressions to convey their message. In other words, each impoliteness strategy and its verbal expression were created intentionally. Impoliteness strategies in this research are understood as various ways to reach a communicative goal: belittle the other. To reach the goal, the public opinions of various Lithuanian public figures (e. g., cultural people, politicians, officials) were collected from new portals in 2019–2023 and analyzed using both quantitative and qualitative approaches. First, problematic aspects of the language policy, for which public figures complain, were identified. Then instances when public figures take a defensive position were analyzed: how they express this position and what it reveals about Lithuanian culture. Findings of this research demonstrate how concepts of impoliteness theory can be applied in analyzing the process of polarization in Lithuanian society on issues related to the State language policy. Also, to reveal how polarization is constructed, these tasks were set: a) determine which impoliteness strategies are used throughout the process of creating polarization, b) analyze how they were expressed verbally (e. g., as an advice, offer, etc.).

Keywords: impoliteness, Lithuanian language policy, polarization, impoliteness strategies

Procedia PDF Downloads 37

Authors: A. A. Adedini, B. A. Aina, P. U. Ogbo

Abstract:

Child obesity is on the rise globally. According to the World Health Organization, the number of obese children would increase to 70 million by 2025 if no intervention is made. An increase in the prevalence of overweight and obesity amongst school children in Lagos State, Nigeria has been established but specific factors promoting its prevalence are unknown. This aim of this study is to identify the commonly expressed factor(s) responsible for the rise in prevalence of child overweight and obesity in Lagos, Nigeria. Five focus group discussions were conducted with different groups of stake-holders involved in child care, namely: parents, teachers and health workers. Participants were recruited using a purposive sampling method; a validated question guide was employed for the discussion sessions. The discussions were recorded, collated, analysed using Grounded theory to extract themes. Six themes emerged from the discussions as follows: Civilization and lifestyle imbalance resulting from busy work schedules of young mothers leading to adoption of westernized culture promoting preference for processed and fast food meals; insecurity and congestion of the state which discourages out-door activities; ignorance of the populace on the prevalence of child obesity in the state; inadequate educative and enlightenment programmes in schools and by the Nigerian government; myths on child care and body physique and societal perceptions of the children born into affluent homes. Some of the factors responsible for the rise in the prevalence of child obesity in Lagos, Nigeria have been identified. Preventive strategies to control the prevalence of obesity in children residing in Lagos state is considered for further studies.

Keywords: Childhood Obesity, factors, lagos state, stakeholders

Procedia PDF Downloads 356

Authors: Valentina Futoryanova, Hugh Hunt

Abstract:

One of the common failure modes of the diesel engine turbochargers is high cycle fatigue of the turbine wheel blades. Mistuning of the blades due to the casting process is believed to contribute to the failure mode. Laser vibrometer is used to characterize mistuning for a population of turbine wheels through the analysis of the blade response to piezo speaker induced noise. The turbine wheel design under investigation is radial and is typically used in 6-12 L diesel engine applications. Amplitudes and resonance frequencies are reviewed and summarized. The study also includes test results for a paddle wheel that represents a perfectly tuned system and acts as a reference. Mass spring model is developed for the paddle wheel and the model suitability is tested against the actual data. Randomization is applied to the stiffness matrix to model the mistuning effect in the turbine wheels. Experimental data is shown to have good agreement with the model.

Keywords: vibration, radial turbines, mistuning, turbine blades, modal analysis, periodic structures, finite element

Procedia PDF Downloads 416

Authors: Nizar Tayem, AbuMuhammad Moinuddeen, Ahmed A. Hussain, Redha M. Radaydeh

Abstract:

This research paper introduces an approach for estimating the direction of arrival (DOA) of multiple RF noncoherent sources in a uniform linear array (ULA). The proposed method utilizes a Capon-like estimation algorithm and incorporates LU decomposition to enhance the accuracy of DOA estimation while significantly reducing computational complexity compared to existing methods like the Capon method. Notably, the proposed method does not require prior knowledge of the number of sources. To validate its effectiveness, the proposed method undergoes validation through both software simulations and practical experimentation on a prototype testbed constructed using a software-defined radio (SDR) platform and GNU Radio software. The results obtained from MATLAB simulations and real-time experiments provide compelling evidence of the proposed method's efficacy.

Keywords: DOA estimation, real-time validation, software defined radio, computational complexity, Capon's method, GNU radio

Procedia PDF Downloads 56

Authors: Lan Du, Yan Wang, Hui Dai

Abstract:

Synthetic aperture radar (SAR) image change detection has recently become a challenging problem owing to the existence of speckle noises. In this paper, an unsupervised distribution-free change detection for SAR image based on scale-invariant feature transform (SIFT) keypoints and segmentation is proposed. Firstly, the noise-robust SIFT keypoints which reveal the blob-like structures in an image are extracted in the log-ratio image to reduce the detection range. Then, different from the traditional change detection which directly obtains the change-detection map from the difference image, segmentation is made around the extracted keypoints in the two original multitemporal SAR images to obtain accurate changed region. At last, the change-detection map is generated by comparing the two segmentations. Experimental results on the real SAR image dataset demonstrate the effectiveness of the proposed method.

Keywords: change detection, Synthetic Aperture Radar (SAR), Scale-Invariant Feature Transformation (SIFT), segmentation

Procedia PDF Downloads 370