Search results for: green smart cities

Authors: Arushi Singh, Anjana Jain, Prakash Vyavahare

Abstract:

Recently, Li-Fi(light-fiedelity) has been launched based on VLC(visible light communication) technique, 100 times faster than WiFi. Now 5G mobile communication system is proposed to use VLC-OFDM as the transmission technique. The VLC system focused on visible rays, is considered for efficient spectrum use and easy intensity modulation through LEDs. The reason of high speed in VLC is LED, as they flicker incredibly fast(order of MHz). Another advantage of employing LED is-it acts as low pass filter results no out-of-band emission. The VLC system falls under the category of ‘green technology’ for utilizing LEDs. In present scenario, OFDM is used for high data-rates, interference immunity and high spectral efficiency. Inspite of the advantages OFDM suffers from large PAPR, ICI among carriers and frequency offset errors. Since, the data transmission technique used in VLC system is OFDM, the system suffers the drawbacks of OFDM as well as VLC, the non-linearity dues to non-linear characteristics of LED and PAPR of OFDM due to which the high power amplifier enters in non-linear region. The proposed paper focuses on reduction of PAPR in VLC-OFDM systems. Many techniques are applied to reduce PAPR such as-clipping-introduces distortion in the carrier; selective mapping technique-suffers wastage of bandwidth; partial transmit sequence-very complex due to exponentially increased number of sub-blocks. The paper discusses three companding techniques namely- µ-law, A-law and advance A-law companding technique. The analysis shows that the advance A-law companding techniques reduces the PAPR of the signal by adjusting the companding parameter within the range. VLC-OFDM systems are the future of the wireless communication but non-linearity in VLC-OFDM is a severe issue. The proposed paper discusses the techniques to reduce PAPR, one of the non-linearities of the system. The companding techniques mentioned in this paper provides better results without increasing the complexity of the system.

Keywords: non-linear companding techniques, peak to average power ratio (PAPR), visible light communication (VLC), VLC-OFDM

Procedia PDF Downloads 277

Authors: Rosaria Tizzani, Tomas Morosinotto, Fabrizio Bezzo, Eleonora Sforza

Abstract:

Red microalga Porphyridium marinum CCAP 13807/10 has the potential to produce a broad range of commercially valuable chemicals such as PhycoErytrin (PE) and sulphated ExoPolySaccharides (EPS). Multiple abiotic factors influence the growth of Porphyridium sp., e.g. the wavelength of the light source and different cultivation strategies (one or two steps, batch, semi-, and continuous regime). The microalga of interest is cultivated in a two-step system. First, the culture grows photoautotrophically in a controlled bioreactor with pH-dependent CO2 injection, temperature monitoring, light intensity, and LED wavelength remote control in a semicontinuous mode. In the second step, the harvested biomass is subjected to mixotrophic conditions to enhance further growth. Preliminary tests have been performed to define the suitable media, salinity, pH, and organic carbon substrate to obtain the highest biomass productivity. Dynamic light and operational conditions (e.g. HRT) are evaluated to achieve high biomass production, high PE accumulation in the biomass, and high EPS release in the medium. Porphyridium marinum is able to chromatically adapt the photosynthetic apparatus to efficiently exploit the full light spectra composition. The effect of specific narrow LED wavelengths (white W, red R, green G, blue B) and a combination of LEDs (WR, WB, WG, BR, BG, RG) are identified to understand the phenomenon of chromatic adaptation under photoautotrophic conditions. The effect of light intensity, residence time, and light quality are investigated to define optimal operational strategies for full scale commercial applications. Production of biomass, phycobiliproteins, PE, EPS, EPS sulfate content, EPS composition, Chlorophyll-a, and pigment content are monitored to determine the effect of LED wavelength on the cultivation Porphyridium marinum in order to optimize the production of these multiple, highly valuable bioproducts of commercial interest.

Keywords: red microalgae, LED, exopolysaccharide, phycoerythrin

Procedia PDF Downloads 98

Authors: Eman. K. Ramadan, Abdelgawad. S. El-Tahawy

Abstract:

The objective of this study was to evaluate the effects of calving season on the production and economic efficiency of dairy farms in Egypt. Our study was performed at dairy production farms in the Alexandria, Behera, and Kafr El-Sheikh provinces of Egypt from summer 2010 to winter 2013. The randomly selected dairy farms had herds consisting of Baladi, Holstein-Friesian, or cross-bred (Baladi × Holstein-Friesian) cows. The data were collected from production records and responses to a structured questionnaire. The average total return differed significantly (P < 0.05) between the different cattle breeds and calving seasons. The average total return was highest for the Holstein-Friesian cows that calved in the winter (29106.42 EGP/cow/year), and it was lowest for Baladi cows that calved in the summer (12489.79 EGP/cow/year). Differences in total returns between the cows that calved in the winter or summer or between the foreign and native breeds, as well as variations in calf prices, might have contributed to the differences in milk yield. The average net profit per cow differed significantly (P < 0.05) between the cattle breeds and calving seasons. The average net profit values for the Baladi cows that calved in the winter or summer were 2413 and 2994.96 EGP/cow/year, respectively, and those for the Holstein-Friesian cows were 10744.17 and 7860.56 EGP/cow/year, respectively, whereas those for the cross-bred cows were 10174.86 and 7571.33 EGP/cow/year, respectively. The variations in net profit might have resulted from variation in the availability or price of feed materials, milk prices, or sales volumes. Our results show that the breed and calving season of dairy cows significantly affected the economic efficiency of dairy farms in Egypt. The cows that calved in the winter produced more milk than those that calved in the summer, which may have been the result of seasonal influences, such as temperature, humidity, management practices, and the type of feed or green fodder available.

Keywords: calving season, economic, production, efficiency, dairy

Procedia PDF Downloads 418

Authors: J. Izan, E.I. Tengku Azmina, F. Pey Thing

Abstract:

Sustainability has been introduced globally since the emerging of the advancement of technology and product development in various aspects. This concept is regarded highly, listed among the seventeenth elements in Sustainable Development Goals (SDG), especially by developed countries in any of their development plans and being considered in the development of the developing countries. It is such as the concept of sustainability can undeniably provide a medium where the cost used by energy consumption and pollution problems can be greatly reduced. In Malaysia, many rules and policies had been advocated to achieve sustainability; however, the practice and implementation as well the enforcement to ensure its implementation are still not great. University, as an educational institution, shall practice and implement sustainability concepts in as much aspect as possible as a positive example for a wider community. University Malaysia Terengganu (UMT) has already published a blueprint guide in 2015, aims to introduce and implement sustainable practice in the university, and solid waste is one of the key elements highlighted. This study was conducted to determine the status of solid waste management practice among the university community associated with several factors that facilitate the room for sustainable management, as drawn in the established blueprint document. The quantitative analysis was carried out via survey conducted online, acquired the questions on green campus concept and implementation in general and solid waste in particular. The results showed that community UMT showed a high level of awareness and knowledge on sustainable solid waste; however, low percentage in managing solid waste in a sustainable manner. Respondents suggested that stringent guidelines and the establishment of policy greatly help in the realization and enforcement of sustainable solid waste handling and management. Facilities such as waste collection centre with separation and segregation containers will motivate the community to practice 3Rs on a daily basis. This will eventually reduce the generation of waste need to be sent to landfill hence reduce the disposal cost. Prolong, and continuous campaign on sustainable solid waste management need to be carried out more frequently.

Keywords: management, solid waste, sustainability, university

Procedia PDF Downloads 90

Authors: S. Fröhlich, M. Herold, M. Allmer

Abstract:

Early stage quantitative analysis of host cell protein (HCP) variations is challenging yet necessary for comprehensive bioprocess development. High resolution mass spectrometry (HRMS) provides a high-end technology for accurate identification alongside with quantitative information. Hereby we describe a flexible HRMS assay platform to quantify HCPs relevant in microbial expression systems such as E. Coli in both up and downstream development by means of MVDA tools. Cell pellets were lysed and proteins extracted, purified samples not further treated before applying the SMART tryptic digest kit. Peptides separation was optimized using an RP-UHPLC separation platform. HRMS-MSMS analysis was conducted on an Orbitrap Velos Elite applying CID. Quantification was performed label-free taking into account ionization properties and physicochemical peptide similarities. Results were analyzed using SIEVE 2.0 (Thermo Fisher Scientific) and SIMCA (Umetrics AG). The developed HRMS platform was applied to an E. Coli expression set with varying productivity and the corresponding downstream process. Selected HCPs were successfully quantified within the fmol range. Analysing HCP networks based on pattern analysis facilitated low level quantification and enhanced validity. This approach is of high relevance for high-throughput screening experiments during upstream development, e.g. for titer determination, dynamic HCP network analysis or product characterization. Considering the downstream purification process, physicochemical clustering of identified HCPs is of relevance to adjust buffer conditions accordingly. However, the technology provides an innovative approach for label-free MS based quantification relying on statistical pattern analysis and comparison. Absolute quantification based on physicochemical properties and peptide similarity score provides a technological approach without the need of sophisticated sample preparation strategies and is therefore proven to be straightforward, sensitive and highly reproducible in terms of product characterization.

Keywords: process analytical technology, mass spectrometry, process characterization, MVDA, pattern recognition

Procedia PDF Downloads 240

Authors: Massimo Miccoli, Luca Marangoni, Alberto Aniello Scaringi, Alessandro Marceddu, Alessandro Amicone

Abstract:

The susceptibility of deep neural networks (DNNs) to adversarial manipulations is a recognized challenge within the computer vision domain. Adversarial examples, crafted by adding subtle yet malicious alterations to benign images, exploit this vulnerability. Various defense strategies have been proposed to safeguard DNNs against such attacks, stemming from diverse research hypotheses. Building upon prior work, our approach involves the utilization of autoencoder models. Autoencoders, a type of neural network, are trained to learn representations of training data and reconstruct inputs from these representations, typically minimizing reconstruction errors like mean squared error (MSE). Our autoencoder was trained on a dataset of benign examples; learning features specific to them. Consequently, when presented with significantly perturbed adversarial examples, the autoencoder exhibited high reconstruction errors. The architecture of the autoencoder was tailored to the dimensions of the images under evaluation. We considered various image sizes, constructing models differently for 256x256 and 512x512 images. Moreover, the choice of the computer vision model is crucial, as most adversarial attacks are designed with specific AI structures in mind. To mitigate this, we proposed a method to replace image-specific dimensions with a structure independent of both dimensions and neural network models, thereby enhancing robustness. Our multi-modal autoencoder reconstructs the spectral representation of images across the red-green-blue (RGB) color channels. To validate our approach, we conducted experiments using diverse datasets and subjected them to adversarial attacks using models such as ResNet50 and ViT_L_16 from the torch vision library. The autoencoder extracted features used in a classification model, resulting in an MSE (RGB) of 0.014, a classification accuracy of 97.33%, and a precision of 99%.

Keywords: adversarial attacks, malicious images detector, binary classifier, multimodal transformer autoencoder

Procedia PDF Downloads 96

Authors: Basave Gowda, Lokesh K., Prasanth S. M., Bellad S. B., Radha J., Lokesh G. Y., Patil S. B., Vijayakumar D. K., Ganigar B. S., Rakesh C. Mathad

Abstract:

Quality seed plays an important role in enhancing the crop productivity. It was reported and confirmed by large scale verification research trials that by use of quality seeds alone, the crop yield can be enhanced by 15 to 20 per cent. At present, the quality seed production and distribution through organised sectors comprising both public and private seed sector was only 20-25% of the requirement and the remaining quantity is met through unorganised sector which include the farmer to farmers saved seeds. With an objective of developing an alternative seed system, the University of Agricultural Sciences, Raichur in Karnataka state has implemented Seed Village Programme in more than 100 villages covering around 5000 farmers every year since 2009-10 and in the selected seed villages, a group of 50-150 farmers were supplied the foundation seeds of new varieties to an extent of 0.4 ha at 50 % subsidy. And two to three training programmes were conducted in the targeted villages for quality seed production and the seed produced in the target group was processed locally in the university seed processing units and arranged for distribution in the local villages by the seed growers themselves. By this new innovative and modified seed system, the university can able to replace old varieties of pigeon pea and green gram by producing 1482, 2978, 2729, 2560, and 4581 tonnes of seeds of new varieties on large scale under farmers and scientists participatory seed village programmes respectively during 2009-10, 2010-11, 2011-12, 2012-13 and 2013-14. From this new alternate model of seed system, there should be large scale promotion of regional seed system involving farmers, NGO and voluntary organisation for quick and effective replacement of old, low yielding, disease susceptible varieties with new high yielding, disease resistant for enhanced food production and food security.

Keywords: seed system, seed village, seed replacement, varietal replacement

Procedia PDF Downloads 418

Authors: Avijit Mahala

Abstract:

Present study is primarily concerned with the physical processes and status of land degradation in a tropical plateau fringe. Chotanagpur plateau is one of the most water erosion related degraded areas of India. The granite gneiss geological formation, low to medium developed soil cover, undulating lateritic uplands, high drainage density, low to medium rainfall (100-140cm), dry tropical deciduous forest cover makes the Silabati River basin a truly representative of the tropical environment. The different physical factors have been taken for land degradation study includes- physiographic formations, hydrologic characteristics, and vegetation cover. Water erosion, vegetal degradation, soil quality decline are the major processes of land degradation in study area. Granite-gneiss geological formation is responsible for developing undulating landforms. Less developed soil profile, low organic matter, poor structure of soil causes high soil erosion. High relief and sloppy areas cause unstable environment. The dissected highland causes topographic hindrance in productivity. High drainage density and frequency in rugged upland and intense erosion in sloppy areas causes high soil erosion of the basin. Decreasing rainfall and increasing aridity (low P/PET) threats water stress condition. Green biomass cover area is also continuously declining. Through overlaying the different physical factors (geological formation, soil characteristics, geomorphological characteristics, etc.) of considerable importance in GIS environment the varying intensities of land degradation areas has been identified. Middle reaches of Silabati basin with highly eroded laterite soil cover areas are more prone to land degradation.

Keywords: land degradation, tropical environment, lateritic upland, undulating landform, aridity, GIS environment

Procedia PDF Downloads 126

Authors: Baikunthanath Sahoo, Santosh Kumar Sahu, Krishna Malakar

Abstract:

With the essence of global environmental sustainability and green business management, the wind of business research moved towards Corporate Social Responsibility. In addition to international and national treaties, businesses have also started realising environmental protection and energy efficiency through CSR as part of business strategy in response to climate change. Considering the ambitious emission reduction target and rapid economic development of India, this study is an attempt to explore the effect of CSR on the energy efficiency management of manufacturing firms in India. By using firm-level data, the panel fixed effect model shows that the CSR dummy variable is negatively influencing the energy intensity or technically, they are energy efficient. The result demonstrates that in the presence of CSR, all the production economic variables are significant. The result also shows that doing environmental expenditure does not improve energy efficiency might be because very few firms are motivated to do such expenditure and also not common to all sectors. The interactive effect model result conforms that without considering CSR dummy as an intervening variable only Manufacturers of Chemical and Chemical products, Manufacturers of Pharmaceutical, medical chemical, and botanical products firms energy intensity low but after considering CSR in their business practices all six sub-sector firms become energy efficient. The empirical result also validate that firms are continuously engaged in CSR activities they are highly energy efficient. It is an important motivational factor for firms to become economically and environmentally sustainable in the corporate world. This analysis would help business practitioners to know how to manage today’s profitability and tomorrow’s sustainability to achieve a comparative advantage in the emerging market economy. The paper concludes that reducing energy consumption as part of their social responsibility to care for the environment, will need collaborative efforts of business society and policy bodies.

Keywords: CSR, Energy Efficiency, Indian manufacturing Sector, Business strategy

Procedia PDF Downloads 73

Authors: Shagufta Tazin Shathy, Mohammad Imam Hasan Reza

Abstract:

Fragmentation due to urbanization and agricultural expansion has become the main reason for destruction of forest area and loss of biodiversity particularly in the developing world. At present, the world is experiencing the largest wave of urban growth in human history, and it is estimated that this influx will be mainly taking place in developing world. Therefore, study on urban fragmentation is vital for a sustainable urban development. Landscape fragmentation is one of the most important conservation issues in the last few decades. Habitat fragmentation due to landscape alteration has caused habitat isolation, destruction in ecosystem pattern and processes. Thus, this research analyses the spatial and temporal extent of urban fragmentation using landscape indices in the Kuala Lumpur (KL) – the capital and most populous city in Malaysia. The objective of this study is to examine the urban fragmentation index in KL city. Fragmentation metrics used in the study are: a) Urban landscape ratio (the ratio of urban landscape area and build up area), b) Infill (development that occurred within urbanized open space), and c) Extension (development of exterior open space). After analyzing all three metrics, these are calculated for the combined urban fragmentation index (UFI). In this combined index, all three metrics are given an equal weight. Land cover/ land use maps of the year 1996 and 2005 have been developed from the Landsat TM 30 m resolution satellite image. The year 1996 is taken as a reference year to analyze the changes. The UFI calculated for the year of 1996 and2005 found that the KL city has undergone rapid landscape changes destructing forest ecosystem adversely. Increasing UFI for the year of 1996 compared to 2005 indicates that the developmental activities have been occupying open spaces and fragmenting natural lands and forest. This index can be implemented in other unplanned and rapidly urbanizing Asian cities for example Dhaka and Delhi to calculate the urban fragmentation rate. The findings from the study will help the stakeholders and urban planners for a sustainable urban management planning in this region.

Keywords: GIS, index, sustainable urban management, urbanization

Procedia PDF Downloads 355

Authors: Magdalena Rusady Goey, Gordon Strathdee, Neil Perkins

Abstract:

Background: Acute lymphoblastic leukaemia (ALL) is the most frequent type of childhood malignancy, accounting for 25% of all cases. TWIST2, a basic helix-loop-helix transcription factor, has been implicated in ALL development. Prior studies found that TWIST2 undergoes epigenetic silencing in more than 50% cases of ALL through promoter hypermethylation and suggested that re-expression of TWIST2 may inhibit cell growth/survival of leukaemia cell lines. TWIST2 has also been implicated as a regulator of NF-kappaB activity, which is constitutively active in leukaemia. Here, we use a lentiviral transductions system to confirm the importance of TWIST2 in controlling leukaemia cell growth and to investigate whether this is achieved through altered regulation of NF-kappaB activity. Method: Re-expression of TWIST2 in leukaemia cell lines was achieved using lentiviral-based transduction. The lentiviral vector also expresses enhanced green fluorescent protein (eGFP), allowing transduced cells to be tracked using flow cytometry. Analysis of apoptosis and cell proliferation were done using annexinV and VPD450 staining, respectively. Result and Discussion: TWIST2-expressing cells were rapidly depleted from a mixed population in ALL cell lines (NALM6 and Reh), indicating that TWIST2 inhibited cell growth/survival of ALL cells. In contrast, myeloid cell lines (HL60 and K562) were comparatively insensitive to TWIST2 re-expression. Analysis of apoptosis and cell proliferation found no significant induction of apoptosis, but did find a rapid induction of proliferation arrest in TWIST2-expressing Reh and NALM6 cells. Initial experiment with NF-kappaB inhibitor demonstrated that inhibition of NF-kappaB has similar impact on cell proliferation in the ALL cell lines, suggesting that TWITST2 may induce cell proliferation arrest through inhibition of NF-kappaB. Conclusion: The results of this study suggest that epigenetic inactivation of TWIST2 in primary ALL leads to increased proliferation, potentially by altering the regulation of NF-kappaB.

Keywords: leukaemia, acute lymphoblastic leukaemia, NF-kappaB, TWIST2, lentivirus

Procedia PDF Downloads 333

Authors: Teklay Tesfay, Gebreyesus Brhane Tesfahunegn, Abadi Berhane, Selemawit Girmay

Abstract:

Adjusting the proper sowing date of a crop at a particular location with a changing climate is an essential management option to maximize crop yield. However, determining the optimum sowing date for rainfed maize production through field experimentation requires repeated trials for many years in different weather conditions and crop management. To avoid such long-term experimentation to determine the optimum sowing date, crop models such as AquaCrop are useful. Therefore, the overall objective of this study was to evaluate the performance of AquaCrop model in simulating maize productivity under varying sowing dates. A field experiment was conducted for two consecutive cropping seasons by deploying four maize seed sowing dates in a randomized complete block design with three replications. Input data required to run this model are stored as climate, crop, soil, and management files in the AquaCrop database and adjusted through the user interface. Observed data from separate field experiments was used to calibrate and validate the model. AquaCrop model was validated for its performance in simulating the green canopy and aboveground biomass of maize for the varying sowing dates based on the calibrated parameters. Results of the present study showed that there was a good agreement (an overall R2 =, Ef= d= RMSE =) between measured and simulated values of the canopy cover and biomass yields. Considering the overall values of the statistical test indicators, the performance of the model to predict maize growth and biomass yield was successful, and so this is a valuable tool help for decision-making. Hence, this calibrated and validated model is suggested to use for determining optimum maize crop sowing date for similar climate and soil conditions to the study area, instead of conducting long-term experimentation.

Keywords: AquaCrop model, calibration, validation, simulation

Procedia PDF Downloads 49

Authors: Lee Artz

Abstract:

Based on content analyses of major US media, immediately following the George Floyd killing in May 2020, some mayors and local, state, and national officials offered favorable representations of protests against police violence. As the protest movement grew to historic proportions with 26 million joining actions in large cities and small towns, dominant representations of racism by elected officials and leading media shifted—replacing both the voices and demands of protestors with representations by elected officials. Major media quoted Black mayors and Congressional representatives who emphasized concerns about looting and the disruption of public safety. Media coverage privileged elected officials who criticized movement demands for defunding police and deplored isolated instances of property damaged by protestors. Subsequently, public opinion polls saw an increase in concern for law and order tropes and a decrease in support for protests against police violence. Black Lives Matter and local organizations had no coordinated response and no effective means of communication to counter dominant representations voiced by politicians and globally disseminated by major media. Politician and media-instigated public opinion shifts indicate that social movements need their own means of communication and collective decision-making--both of which were largely missing from Black Lives Matter leaders, leading to disaffection and a political split by more than 20 local affiliates. By itself, social media by myriad individuals and groups had limited purchase as a means for social movement communication and organization. Lacking a collaborative, coordinated strategy, organization, and independent media, the loose network of Black Lives Matter groups was unable to offer more accurate, democratic, and favorable representations of protests and their demands for more justice and equality. The fight for equality was diverted by the fight for representation.

Keywords: black lives matter, public opinion, racism, representations, social movements

Procedia PDF Downloads 172

Authors: Yueying Chen

Abstract:

A city can be developed through memory, and memory is one of the most important elements for urban contexts. Collective memory is a collection of personal memories that can be preserved with objects, places, and events of heritage, expressing culture through spatial changes. These preserved forms can evoke a sense of community and certain emotions. Collective memory in cities reflects urban spatial alterations and historical developments. It can be preserved and reflected by revitalisation projects. A major current focus in collective memory research is how to identify and preserve memory in an intangible way. The influential elements within the preservation of collective memory mainly include institutions and objects. However, current research lacks the assessment of the collective memory after alterations of urban heritage. The assessment of urban heritage lacks visualization and qualitative methods. The emergence of the application of space syntax can fill in this gap. Hengshan Mansions was a new project in 2015. The original residential area has been replaced with a comprehensive commercial area integrating boutique shopping, upscale restaurants, and creative offices. Hengshan Mansions is located in the largest historic area in Shanghai, and its development is the epitome of the traditional culture in Shanghai. Its alteration is the newest project in this area and presents the new concept of revitalisation of urban heritage. For its physical parts, modern vitality is created, and historical information is preserved at the same time. However, most of the local people are moved away, and its functions are altered a lot. The preservation of its collective memory needs to discuss furtherly. Thus, the article builds a framework to assess the collective memory of urban heritage, including spatial configuration, spatial interaction, and cultural cognition. Then, it selects Hengshan Mansions in Shanghai as a case to analyse the assessed framework. Space syntax can be applied to visualize the assessment. Based on the analysis, the article will explore the influential reasons for the collective memory after alterations and proposes relevant advice for the preservation of the collective memory of urban heritage.

Keywords: collective memory, alternation of urban heritage, space syntax, Hengshan Mansions

Procedia PDF Downloads 116

Authors: Parul Kapoor, Dheeraj Bhardwaj

Abstract:

Delhi and other Indian cities accommodate thousands of Central Government employees in housing complexes called ‘General Pool Residential Accommodation’ (GPRA), located in prime parcels of the city. These residential colonies are now undergoing redevelopment at a massive scale, significantly impacting the ecology of the surrounding areas. Essentially, these colonies were low-rise, low-density planned developments with a dense tree cover and minimal parking requirements. But with increasing urbanisation and spike in parking demand, the proposed built form is an aggregate of high-rise gated complexes, redefining the skyline of the city which is a huge departure from the mediocre setup of Low-rise Walk-up apartments. The complexity of these developments is further aggravated by the need for parking which necessitates cutting huge number of trees to accommodate multiple layers of parking beneath the structures thus sidelining the authentic character of these areas which is laden with a dense tree cover. The aftermath of this whole process is the generation of a huge carbon footprint on the surrounding areas, which is unaccounted for, in the planning and design practice. These developments are currently planned as mix-use compounds with large commercial built-up spaces which have additional parking requirements over and above the residential parking. Also, they are perceived as gated complexes and not as neighborhood units, thus project isolated images of high-rise, dense systems with little context to the surroundings. The paper would analyze case studies of GPRA Redevelopment projects in Delhi, and the lack of relevant development control regulations which have led to abnormalities and complications in the entire redevelopment process. It would also suggest policy guidelines which can establish comprehensive codes for effective planning of these settlements.

Keywords: gated complexes, GPRA Redevelopment projects, increased densities, huge carbon footprint, mixed-use development

Procedia PDF Downloads 114

Authors: Young Nam Chun, Soo Hyuk Yun, Byeo Ri Jeong

Abstract:

The recent gradual increase in the energy demand is mostly met by fossil fuel, but the research on and development of new alternative energy sources is drawing much attention due to the limited fossil fuel supply and the greenhouse gas problem. Biomass is an eco-friendly renewable energy that can achieve carbon neutrality. The conversion of the biomass sludge wastes discharged from a wastewater treatment plant to clean energy is an important green energy technology in an eco-friendly way. In this NRF study, a new type of microwave thermal treatment was developed to apply the biomass-CCS technology to sludge wastes. For this, the microwave dielectric heating characteristics were examined to investigate the energy conversion mechanism for the combined drying-pyrolysis/gasification of the dewatered wet sludge. The carbon dioxide gasification was tested using the CO2 captured from the pre-combustion capture process. In addition, the results of the pyrolysis and gasification test with the wet sludge were analyzed to compare the microwave energy conversion results with the results of the use of the conventional heating method. Gas was the largest component of the product of both pyrolysis and gasification, followed by sludge char and tar. In pyrolysis, the main components of the producer gas were hydrogen and carbon monoxide, and there were some methane and hydrocarbons. In gasification, however, the amount of carbon monoxide was greater than that of hydrogen. In microwave gasification, a large amount of heavy tar was produced. The largest amount of benzene among light tar was produced in both pyrolysis and gasification. NH3 and HCN which are the precursors of NOx, generated as well. In microwave heating, the sludge char had a smooth surface, like that of glass, and in the conventional heating method with an electric furnace, deep cracks were observed in the sludge char. This indicates that the gas obtained from the microwave pyrolysis and gasification of wet sewage sludge can be used as fuel, but the heavy tar and NOx precursors in the gas must be treated. Sludge char can be used as solid fuel or as a tar reduction adsorbent in the process if necessary. This work supported by the National Research Foundation of Korea (NRF) grant funded by the Korea government (MSIP) (No. 2015R1R1A2A2A03003044).

Keywords: microwave heating, pyrolysis gasification, precombustion CCS, sewage sludge, biomass energy

Procedia PDF Downloads 309

Authors: F. Berahmandpour, K. Bagheri

Abstract:

Introduction: Spirulina is nutritious blue - green algae which are used as supplement or a preservative in many foods. The studies about the algae argue that the Spirulina can improve immune system, increase fat utilization, reduce oxidative stress and promote endurance at high-intensity exercise. The purpose of study is to assess the effects of Spirulina supplement on healthy weight control. Method: the study is a cross-sectional study which had 30 participants. The participants were men and women who referred to the nutrition and diet therapy clinic (in west of Tehran / Iran) for control weight. The sampling was a purposeful sampling. The participants were divided into three groups, and they were surveyed for 4 weeks. In the first group, 10 participants were used Spirulia supplement (dose: 500mg of Spiruvit Supplement as tablet / 3 times per day) without any special diet. The second group was 10 participants who received Spirulia supplement (dose 500mg of Spiruvit Supplement as tablet / 3 times per day) with a weight loss exercise program and without any special diet. The third group was 10 participants who used Spirulia supplement (dose 500mg of Spiruvit Supplement as tablet / 3 times per day) with an optimum weight loss diet. Results and Discussion: The results show that there were not any significant loss weights in first group. In while, the participants of second group argued that the Spirulina supplement had positive effects on their mud and physical body; however the clinical results showed that the loss weight had fixed tilt in this group. The significant results of study were related to the third group, because the participations could continuous loss weight during 4 weeks. However, the optimum weight loss diets were effective effects on weight loss in this group, but the researchers found that Spirulina supplement could improve loss weight with set of hormonal system (especially in women with menopause). Conclusion: The study is concluded that the Spirulina as a supplement (Spiruvit Supplement) can be an effective effect on healthy weight control, if it is used with a nutritious healthy weight loss diet. In fact, the effect of Spirulina can be related to powerful antioxidant effects and improvable hormonal system in the body.

Keywords: diet, healthy weight control, spirulina, spiruvit supplement

Procedia PDF Downloads 292

Authors: Wudneh Asegedech Ayele

Abstract:

Background: Dietary diversity is strongly related with non-communicable disease (NCDs). Diet plays a key role as a risk factor for hypertension. Diets rich in fruits, vegetables, and low-fat dairy products that include whole grains, poultry, fish, and nuts, that contain only small amounts of red meat, sweets, and sugar-containing beverages, and that contain decreased amounts of total and saturated fat and cholesterol have been found to have a protective effect against hypertension. Methods: hospital based Cross-sectional study design was employed from June 1-June 25, 2021. Sampling technique was Systematic random sampling and data were collected using an interview method. Data were entered into Epi Data version 3.1 and exported to SPSS version 25 for processed and analysis respectively. Descriptive statistics were used to summarize data. Bivariate and multivariate logistic regression will employed to determine dietary diversity among hypertension patients. Results: Adequate dietary diversity score were 96 (24.68%). Most of them cereal, white roots and tubers, dark green leafy vegetables, Vitamin A rich fruits ,meat, egg and coffee or tea more intakes. Hypertensive patients who didn’t consume cereals four times less likely adequate dietary diversity than who consumed cereals [AOR= 4.083, 95%: CI (2.096 -7.352)]. Hypertensive patients who didn’t consume white roots and tubers 14 times less likely adequate dietary diversity than who consumed white roots and tubers [AOR= 13.733, 95% CI: (5.388-34.946)]. Conclusion and recommendation the study showed one of fourth part reported adequate dietary diversity score. Cereals, fruits, vegetables and milk and milk products were statistically associated with dietary diversity practice. Health education about dietary modifications and behavioral change to dietary diversity

Keywords: dietary diversity practice and associated facrors among hypertension patients at tirunesh beijing hospital, hypertension, dietary, diversity and tirunesh beijing hospital, associated facrors among hypertension patient, at tirunesh beijing hospita

Procedia PDF Downloads 17

Authors: Sreejith Jayachandran, Mojtaba Ghods, Morteza Mohammadzaheri

Abstract:

The modern busy world is running behind new embedded technologies based on computers and software; meanwhile, some people forget to do their health condition and regular medical check-ups. Some of them postpone medical check-ups due to a lack of time and convenience, while others skip these regular evaluations and medical examinations due to huge medical bills and hospital expenses. Engineers and medical experts have come together to give birth to a new device in the telemonitoring system capable of monitoring, checking, and evaluating the health status of the human body remotely through the internet for the needs of all kinds of people. The remote health monitoring device is a microcontroller-based embedded unit. Various types of sensors in this device are connected to the human body, and with the help of an Arduino UNO board, the required analogue data is collected from the sensors. The microcontroller on the Arduino board processes the analogue data collected in this way into digital data and transfers that information to the cloud, and stores it there, and the processed digital data is instantly displayed through the LCD attached to the machine. By accessing the cloud storage with a username and password, the concerned person’s health care teams/doctors and other health staff can collect this data for the assessment and follow-up of that patient. Besides that, the family members/guardians can use and evaluate this data for awareness of the patient's current health status. Moreover, the system is connected to a Global Positioning System (GPS) module. In emergencies, the concerned team can position the patient or the person with this device. The setup continuously evaluates and transfers the data to the cloud, and also the user can prefix a normal value range for the evaluation. For example, the blood pressure normal value is universally prefixed between 80/120 mmHg. Similarly, the RHMS is also allowed to fix the range of values referred to as normal coefficients. This IoT-based miniature system (11×10×10) cm³ with a low weight of 500 gr only consumes 10 mW. This smart monitoring system is manufactured with 100 GBP, which can be used not only for health systems, it can be used for numerous other uses including aerospace and transportation sections.

Keywords: embedded technology, telemonitoring system, microcontroller, Arduino UNO, cloud storage, global positioning system, remote health monitoring system, alert system

Procedia PDF Downloads 73

Authors: Vikas Kumar

Abstract:

Portable batteries are reliable source of mobile energy to power smart wearable electronics, medical devices, communications, and others internet of thing (IoT) devices. There is a continuous increase in demand for thinner, more flexible battery with high energy density and reliability to meet the requirement. For a flexible battery, factors that affect these properties are the stability of current collectors, electrode materials and their interfaces with the corrosive electrolytes. State-of-the-art conventional and flexible batteries utilise carbon as an electrode and current collectors which cause high internal resistance (~100 ohms) and limit the peak current to ~1mA. This makes them unsuitable for a wide range of applications. Replacing the carbon parts with metallic components would reduce the internal resistance (and hence reduce parasitic loss), but significantly increases the risk of corrosion due to galvanic interactions within the battery. To overcome these challenges, low cost electroplated nickel (Ni) on copper (Cu) was studied as a potential anode current collector for a zinc-manganese oxide primary battery with different concentration of NH4Cl/ZnCl2 electrolyte. Using electrical impedance spectroscopy (EIS), we monitored the open circuit potential (OCP) of electroplated nickel (different thicknesses) in different concentration of electrolytes to optimise the thickness of Ni coating. Our results show that electroless Ni coating suffer excessive corrosion in these electrolytes. Corrosion rates of Ni coatings for different concentrations of electrolytes have been calculated with Tafel analysis. These results suggest that for electroplated Ni, channelling and/or open porosity is a major issue, which was confirmed by morphological analysis. These channels are an easy pathway for electrolyte to penetrate thorough Ni to corrode the Ni/Cu interface completely. We further investigated the incorporation of a special printed graphene layer on Ni to provide corrosion protection in this corrosive electrolyte medium. We find that the incorporation of printed graphene layer provides the corrosion protection to the Ni and enhances the chemical bonding between the active materials and current collector and also decreases the overall internal resistance of the battery system.

Keywords: corrosion, electrical impedance spectroscopy, flexible battery, graphene, metal current collector

Procedia PDF Downloads 118

Authors: Aleksandra Szurlej-Kielanska, Lucyna Pilacka, Dariusz Górecki

Abstract:

The dynamic development of wind energy requires the simultaneous implementation of effective systems minimizing the risk of collisions between birds and wind turbines. Wind turbines are installed in more and more challenging locations, often close to the natural environment of birds. More and more countries and organizations are defining guidelines for the necessary functionality of such systems. The minimum bird detection distance, trajectory tracking, and shutdown time are key factors in eliminating collisions. Since 2020, we have continued the survey on the validation of the subsequent version of the BPS detection and reaction system. Bird protection system (BPS) is a fully automatic camera system which allows one to estimate the distance of the bird to the turbine, classify its size and autonomously undertake various actions depending on the bird's distance and flight path. The BPS was installed and tested in a real environment at a wind turbine in northern Poland and Central Spain. The performed validation showed that at a distance of up to 300 m, the BPS performs at least as well as a skilled ornithologist, and large bird species are successfully detected from over 600 m. In addition, data collected by BPS systems installed in Spain showed that 60% of the detections of all birds of prey were from individuals approaching the turbine, and these detections meet the turbine shutdown criteria. Less than 40% of the detections of birds of prey took place at wind speeds below 2 m/s while the turbines were not working. As shown by the analysis of the data collected by the system over 12 months, the system classified the improved size of birds with a wingspan of more than 1.1 m in 90% and the size of birds with a wingspan of 0.7 - 1 m in 80% of cases. The collected data also allow the conclusion that some species keep a certain distance from the turbines at a wind speed of over 8 m/s (Aquila sp., Buteo sp., Gyps sp.), but Gyps sp. and Milvus sp. remained active at this wind speed on the tested area. The data collected so far indicate that BPS is effective in detecting and stopping wind turbines in response to the presence of birds of prey with a wingspan of more than 1 m.

Keywords: protecting birds, birds monitoring, wind farms, green energy, sustainable development

Procedia PDF Downloads 60

Authors: Sara S. Fouad, Omneya Messallam

Abstract:

In 1818, a seventy-five kilometer long canal was dug (called the Mahmoudiyah canal) connecting between Alexandria city in Egypt and the western branch of the Nile. It was a productive resource and vital to its environment, context, transportation, and recreation. It played a significant role in people’s lives and Alexandria city’s shape. The canal, which was the main vein of goods’ transporting from Alexandria’s seaport to the different parts of Egypt, was still in use today as a major source of clear water in the city. But nowadays, Mahmoudiyah canal is converting into ‘dead waterway’. The canal became sources of pollution as a result of solid and industrial waste thus causing many diseases, destroying communities and biodiversity, with urban invasion, the loss of community aesthetic value and healthy environment. Therefore, this paper aims to propose an urban strategy, as a solution to revive the forgotten canal, through recreating a cultural promenade on its shore. The main aim of this research is to formulate decent quality of life, unpolluted space, an area gathering the city space for nature, tourism and investments. As a case study, this paper investigates Mahmoudiyah canal through urban and ecological analyses, aiming to design an urban strategy for reviving it by creating a cultural promenade enriched with public spaces and green areas, which can most probably enhance the quality of life, city re-living and development. Community participation is also considered as vital and intrinsic implementation stage. The empirical research involved using several data assembly methods such as interviews, mental mapping, structural observations and questionnaires. The paper ends with a set of conclusions leading to proposals for the Mahmoudiyah canal revitalization considering the complex challenges and processes of sustainable regeneration focusing on city’s rehabilitation and lost identity.

Keywords: Mahmoudiyah canal, community aesthetic value, city re-living, cultural promenade

Procedia PDF Downloads 119

Authors: Naveed Mazhar

Abstract:

Our cities are known to have significant modifying effects on the local climate. The nature of the modifications depends on a range of physical variables, usually assessed at a wide range of spatial scales. Physical spatial dimensions, such as measured parameters of microclimates and their significant influence on human sensations, are known to have far-reaching effects on human thermal comfort and by corollary a force that influences human perception. Less scholarship has thrown light on the subjective dimension and insufficiently demonstrates a relational approach between human behavior and how it is affected by the phenomenon of urban microclimates. Other than identifying gaps in the most recent scholarship and providing future research opportunities, the scope of this study will help improve urban design guidelines and raise framework standards of socially responsive urban design. This study will help equip future professionals to ameliorate the effects of urban microclimates on participant’s perceptions enabling more frequent usage of the outdoor urban spaces. However, it is informed that the physical parameters of an outdoor open space determine psychological human adaptations and is a measure of the degree to which people are willing to adapt to their surroundings. A large amount of research is available related to urban microclimates. However, very few studies are focused on the elucidation of the critical factors influencing human perceptions of the microclimates in urban spatial configurations. Based on the most recent scholarship, this study has evaluated the role urban microclimatic conditions have in the formation of human perceptions and, by extension, behavioral patterns formulating in outdoor open spaces. Furthermore, this study also defines, in the backdrop of the current scholarly literature, the socio-spatial interdependence of behavioral patterns with relationship to the built urban fabric and its resultant correlation with human perception. A comprehensive review and analysis of the recent research conducted within the scope of the study will help frame gaps, issues, current research methods and future research opportunities.

Keywords: urban design, urban microcliamate, human perception, human behavioral patterns

Procedia PDF Downloads 286

Authors: Sabina Klimek

Abstract:

In general, entrepreneurs are viewed as agents of change whose goal is to ensure that resources are efficiently utilized. They are very important in the global economy; they create wealth and provide jobs. At the same time, many policymakers say that women entrepreneurs are a ‘special group’ worthy of their own research and policies. The status of Polish women has been changing as well, even though, to a large extent, it is still defined by the double role that women are expected to fill according to the dominant stereotypical model of family life. However, in the past decade, Polish women’s economic activities have experienced rapid growth and today are at a high level. In the article, the author presents the results of a survey conducted among women entrepreneurs in Poland concerning the functioning of their enterprises, motivation in setting up a company, and barriers that hinder them in business. The questionnaire (300 questionnaires were provided) and case studies carried out by the author have proven that female entrepreneurs in Poland are characterized by commonalities. Mostly they run small or micro-enterprises, operate in larger cities, are well-educated, and run service companies. Their main motivation to run their own business is mostly indicated by their need for independence. However, one of their biggest barriers and hesitations is the apprehension of non-payment. Entrepreneurs want to develop their companies, go to foreign markets and implement new solutions. They are not afraid of the future; they are only trying to create it. Detailed hypothesis, which reads as follows. The author additionally conducted a macroeconomic analysis calculating what part of GDP in Poland is produced by female entrepreneurs. The results of the study presented in this article prove that female entrepreneurship in Poland has a stable impact on the economy of the country, and women entrepreneurs produce over 13% of the national GDP. After years of growth in the number of female entrepreneurs in Poland, there has been a period of stabilization. However, there has also been a reduction in the number of self-employed people as well as the number of women in total employment. In the article, the author analyses the reasons for decreasing number of self-employed women and the total employment of women in Poland and provides suggestions for steps and incentives that should be made in order to encourage female entrepreneurship to grow in the country.

Keywords: women entrepreneurship, women in business, women entrepreneurship in Poland, Poland, GDP of Poland

Procedia PDF Downloads 70

Authors: Kishor Chandra Kandpal, Amit Kumar

Abstract:

The Indian Himalaya region harbours approximately 1748 plants of medicinal importance, and as per International Union for Conservation of Nature (IUCN), the 112 plant species among these are threatened and endangered. To ease the pressure on these plants, the government of India is encouraging its in-situ cultivation. The Saussurea costus, Valeriana jatamansi, and Picrorhiza kurroa have also been prioritized for large scale cultivation owing to their market demand, conservation value and medicinal properties. These species are found from 1000 m to 4000 m elevation ranges in the Indian Himalaya. Identification of these plants in the field requires taxonomic skills, which is one of the major bottleneck in the conservation and management of these plants. In recent years, Hyperspectral remote sensing techniques have been precisely used for the discrimination of plant species with the help of their unique spectral signatures. In this background, a spectral library of the above 03 medicinal plants was prepared by collecting the spectral data using a handheld spectroradiometer (325 to 1075 nm) from farmer’s fields of Himachal Pradesh and Uttarakhand states of Indian Himalaya. The Random forest (RF) model was implied on the spectral data for the classification of the medicinal plants. The 80:20 standard split ratio was followed for training and validation of the RF model, which resulted in training accuracy of 84.39 % (kappa coefficient = 0.72) and testing accuracy of 85.29 % (kappa coefficient = 0.77). This RF classifier has identified green (555 to 598 nm), red (605 nm), and near-infrared (725 to 840 nm) wavelength regions suitable for the discrimination of these species. The findings of this study have provided a technique for rapid and onsite identification of the above medicinal plants in the field. This will also be a key input for the classification of hyperspectral remote sensing images for mapping of these species in farmer’s field on a regional scale. This is a pioneer study in the Indian Himalaya region for medicinal plants in which the applicability of hyperspectral remote sensing has been explored.

Keywords: himalaya, hyperspectral remote sensing, machine learning; medicinal plants, random forests

Procedia PDF Downloads 194

Authors: Çisem Gündüz Arabacı

Abstract:

Deliberation has been seen one of the most important components of democratic ideals especially since liberal democratic attributions have been under fire. Deliberative democracy advocates that people should participate in collective decision-making processes by other mechanisms rather than conventional ones in order to reach legitimate decisions. Deliberative democratic theory makes emphasis on deliberative communication between people and encourages them not to merely express their political opinions (through surveys and referendum) but to form those opinions through public debates. This paper focuses on deliberative democratic visions of Gezi Park Public Forums by taking deliberative democracy as theoretical basis and examining Gezi Park Public Forums in the light of core elements of deliberative democracy. Gezi Movement started on 28 May 2013 in İstanbul as a reaction to local government's revision plans for Taksim Gezi Park, spread throughout the country and created new zones in public sphere which are called Public Park Forums. During the summer of 2013, especially in İstanbul but also in other cities, people gathered in public parks, discussed and took collective decisions concerning actions which they will take. It is worth to mention that since 3 and half years some Public Park Forums are still continuing their meetings regularly in city of İzmir. This paper analyzes four 'Public Park Forums' in İzmir which are called Bornova Public Forum; Karşıyaka Public Forum, Foça Public Forum and Güzelyalı Public Forum. These Forums are under investigation in terms of their understanding of democracy and the values that support that understanding. Participant observation and in-depth interview methods are being used as research methods. Core element of deliberative democracy are being collected under three main category: common interest versus private interest, membership, rational argument and these values are being questioning within one of each Forum in order to draw an overall picture and also make comparison between them. Discourse analysis is being used in order to examine empirical data and paper aims to reveal how participants of public forums perceive deliberative democratic values and whether they give weight to these values.

Keywords: deliberative democracy, Gezi Park movement, public forums, social movement

Procedia PDF Downloads 304

Authors: Huseyin Arasli, Maryam Abdullahi, Tugrul Gunay

Abstract:

One of the prominence elements used by the destination marketing organization (DMO) as a marketing strategy is the application of Social media tools. During the current spread of coronavirus disease (COVID-19), travel restriction was placed in most countries of the world, leading to the closure of borders movement. It should be noted that most tourism travelers depend on social media to obtain and exchange different kinds of information about COVID-19 in an unprecedented scale. The situational information people received is valued, which calls for the response of the tourism industry on the epidemic. Therefore, it is highly important to recognize such situational information and to understand how people spread this propaganda on social media platforms so that suitable information that relates the COVID-19 epidemic is available in a manner that will not tarnish the marketing strategies, festival planners. Data for this research study was collected from the desk review, which is a secondary source data, online blogs, and interview through social media chat. The results of this research show that the widespread of COVID-19 pandemics led to rapid lockdown in states and cities all over Nigeria, causing declining demands in hotels, airlines, recreation, and tourism centers. Additionally, billions of dollars lost has been recorded in the high increase of hotels and travel bookings cancellations which caused hundreds and thousands of job loss in the country. The result of this research also revealed that COVID-19 is causing more havoc on the unemployment rate indices of the country. Similarly, the over-dependence of government on petroleum has further caused considerable revenue loss, thereby raising a high poverty rate among less privileged Nigerians. Based on this result, the study suggested that there is an urgent need for the government to diversify its economy by looking at other different sectors such as tourism and agricultural farm produce to harmonize other commercial trades sectors in the country.

Keywords: social media, destination marketing organizations, DMOs, cultural COVID-19, coronavirus, hospitality, travel tour, tourism

Procedia PDF Downloads 93

Authors: Lauren B. Birney

Abstract:

Summer STEM Institute for Middle and High School Students at Pace University The STEM Collaboratory NYC® Summer Fellows Institute takes place on Pace University’s New York City campus during July and provides the following key features for all participants: (i) individual meetings with Pace faculty to discuss and refine future educational goals; (ii) mentorship, guidance, and new friendships with program leaders; and (iii) guest lectures from professionals in STEM disciplines and businesses. The Summer STEM Institute allows middle school and high school students to work in teams to conceptualize, develop, and build native mobile applications that teach and reinforce skills in the sciences and mathematics. These workshops enhance students’STEM problem solving techniques and teach advanced methods of computer science and engineering. Topics include: big data and analytics at the Big Data lab at Seidenberg, Data Science focused on social and environmental advancement and betterment; Natural Disasters and their Societal Influences; Algal Blooms and Environmental Impacts; Green CitiesNYC; STEM jobs and growth opportunities for the future; renew able energy and sustainable infrastructure; and climate and the economy. In order to better align the existing Summer STEM, Institute with the CCERS model and expand the overall network, Pace is actively recruiting new content area specialists from STEM industries and private sector enterprises to participate in an enhanced summer institute in order to1) nurture student progress and connect summer learning to school year curriculum, 2) increase peer-to-peer collaboration amongst STEM professionals and private sector technologists, and 3) develop long term funding and sponsorship opportunities for corporate sector partners to support CCERS schools and programs directly.

Keywords: environmental restoration science, citizen science, data science, STEM

Procedia PDF Downloads 73

Authors: Waddah Abdullah, Saleh Al-Sarem

Abstract:

Electrokinetic remediation was undoubtedly proven to be one of the most efficient techniques used to clean up soils contaminated with polar charged contaminants (such as heavy metals) and non-polar organic contaminants. It can be efficiently used to clean up low permeability mud, wastewater, electroplating wastes, sludge, and marine dredging. This study presented and discussed the results of electrokinetic remediation processes to clean up soils contaminated with nickel. Two types of electrokinetics cells were used: an open cell and an advanced cylindrical cell. Two types of soils were used for this investigation; the Azraq green clay which has very low permeability taken from the eastern part of Jordan (city of Azraq) and a sandy soil having, relatively, very high permeability. The clayey soil was spiked with 500 ppm of nickel, and the sandy soil was spiked with 1500 ppm of nickel. Fully saturated and partially saturated clayey soils were used for the clean-up process. Clayey soils were tested under a direct current of 80 mA and 50 mA to study the effect of the electrical current on the remediation process. Chelating agent (Na-EDTA), disodium ethylene diamine tetraacetatic acid, was used in both types of soils to enhance the electroremediation process. The effect of carbonates presence in the contaminated soils, also, was investigated by use of sodium carbonate and calcium carbonate. pH changes in the anode and the cathode compartments were controlled by use of buffer solutions. The results of the investigation showed that for the fully saturated clayey soil spiked with nickel had an average removal efficiency of 64%, and the average removal efficiency was 46% for the unsaturated clayey soil. For the sandy soil, the average removal efficiency of Nickel was 90%. Test results showed that presence of carbonates in the remediated soils retarded the clean-up process of nickel-contaminated soils (removal efficiency was reduced from 90% to 60%). EDTA enhanced decontamination of nickel contaminated clayey and sandy soils with carbonates was studied. The average removal efficiency increased from 60% (prior to using EDTA) to more than 90% after using EDTA.

Keywords: buffer solution, EDTA, electroremediation, nickel removal efficiency

Procedia PDF Downloads 173

Authors: S. Reshma Reghu, Shiburaj Sugathan, T. G. Nandu, K. B. Ramesh Kumar, Mathew Dan

Abstract:

Bacterial diseases are considered to be one of the most prevalent health hazards in the developing world and many bacteria are becoming resistant to existing antibiotics making the treatment ineffective. Thus, it is necessary to find novel targets and develop new antibacterial drugs with a novel mechanism of action. The process of bacterial cell division is a novel and attractive target for new antibacterial drug discovery. FtsZ, a homolog of eukaryotic tubulin, is the major protein of the bacterial cell division machinery and is considered as an important antibacterial drug target. Zingiberaceae, the Ginger family consists of aromatic herbs with creeping rhizomes. Many of these plants have antimicrobial properties.This study aimed to determine the anti-bacterial activity of selected Zingiberaceous plants by targeting bacterial cell division protein, FtsZ. Essential oils and methanol extracts of Amomum ghaticum, Alpinia galanga, Kaempferia galanga, K. rotunda, and Zingiber officinale were tested to find its antibacterial efficiency using disc diffusion method against authentic bacterial strains obtained from MTCC (India). Essential oil isolated from A.galanga and Z.officinale were further assayed for FtsZ inhibition assay following non-radioactive malachite green-phosphomolybdate assay using E. coli FtsZ protein obtained from Cytoskelton Inc., USA. Z.officinale essential oil possess FtsZ inhibitory property. A molecular docking study was conducted with the known bioactive compounds of Z. officinale as ligands with the E. coli FtsZ protein homology model. Some of the major constituents of this plant like catechin, epicatechin, and gingerol possess agreeable docking scores. The results of this study revealed that several chemical constituents in Ginger plants can be utilised as potential source of antibacterial activity and it can warrant further investigation through drug discovery studies.

Keywords: antibacterial, FtsZ, zingiberaceae, docking

Procedia PDF Downloads 466