Search results for: simplified higher-order deformation theory
Commenced in January 2007
Frequency: Monthly
Edition: International
Paper Count: 5911

Search results for: simplified higher-order deformation theory

4741 Experimental Study Analyzing the Similarity Theory Formulations for the Effect of Aerodynamic Roughness Length on Turbulence Length Scales in the Atmospheric Surface Layer

Authors: Matthew J. Emes, Azadeh Jafari, Maziar Arjomandi

Abstract:

Velocity fluctuations of shear-generated turbulence are largest in the atmospheric surface layer (ASL) of nominal 100 m depth, which can lead to dynamic effects such as galloping and flutter on small physical structures on the ground when the turbulence length scales and characteristic length of the physical structure are the same order of magnitude. Turbulence length scales are a measure of the average sizes of the energy-containing eddies that are widely estimated using two-point cross-correlation analysis to convert the temporal lag to a separation distance using Taylor’s hypothesis that the convection velocity is equal to the mean velocity at the corresponding height. Profiles of turbulence length scales in the neutrally-stratified ASL, as predicted by Monin-Obukhov similarity theory in Engineering Sciences Data Unit (ESDU) 85020 for single-point data and ESDU 86010 for two-point correlations, are largely dependent on the aerodynamic roughness length. Field measurements have shown that longitudinal turbulence length scales show significant regional variation, whereas length scales of the vertical component show consistent Obukhov scaling from site to site because of the absence of low-frequency components. Hence, the objective of this experimental study is to compare the similarity theory relationships between the turbulence length scales and aerodynamic roughness length with those calculated using the autocorrelations and cross-correlations of field measurement velocity data at two sites: the Surface Layer Turbulence and Environmental Science Test (SLTEST) facility in a desert ASL in Dugway, Utah, USA and the Commonwealth Scientific and Industrial Research Organisation (CSIRO) wind tower in a rural ASL in Jemalong, NSW, Australia. The results indicate that the longitudinal turbulence length scales increase with increasing aerodynamic roughness length, as opposed to the relationships derived by similarity theory correlations in ESDU models. However, the ratio of the turbulence length scales in the lateral and vertical directions to the longitudinal length scales is relatively independent of surface roughness, showing consistent inner-scaling between the two sites and the ESDU correlations. Further, the diurnal variation of wind velocity due to changes in atmospheric stability conditions has a significant effect on the turbulence structure of the energy-containing eddies in the lower ASL.

Keywords: aerodynamic roughness length, atmospheric surface layer, similarity theory, turbulence length scales

Procedia PDF Downloads 123
4740 Being Funny is a Serious Business for Feminine Brands

Authors: Mohammed Murtuza Soofi

Abstract:

Purpose: Marketers and Researchers alike have simultaneously, yet in mutually exclusive instances, promote the use of humour by brands in their communication and gendering of brands, as both enhance brand equity and can generate positive attitudinal responses from customers. However, the gendering of brands comes with associated gendered stereotypical expectations. The current paper consolidates the long standing literature on gender role/stereotype theory and brand gender theories establishing a theoretical framework for understanding how gender-based stereotypes about humour can influence consumers’ attitudinal responses towards brands. Design/methodology/approach: Using parallel constrain satisfaction theory as domain theory to explain the highhandedness of stereotypes and gender stereotype theories (particularly around feminine use of humour), we explain why gender based stereotypes could constrain brand behaviors, and in turn, feminine brands get penalised for using witty, aggressive and self-enhancing humor. Findings: Extension of gender stereotypes to anthropomorphised brands will lead consumers to judge the use of negative humour by a feminine brand as less appropriate, which will trigger the causal chain of reduced sense of communal appropriateness and brand warmth which will result in a negative attitude towards the brand. Originality/value: Brand gendering being susceptible to gender based stereotypes, has very little attention in the literature and hence use of negative humour (stereotypical male behaviour), has never been studied in the context of gendered brands. It also helps understand to what extent stereotypes will impact attitudinal responses to the brand. Our work can help understand when heavily gendered brands can optimise the use of humour and when they can avoid it.

Keywords: brand femininity, brand gender, gender stereotypes, humour

Procedia PDF Downloads 202
4739 Performance Analysis of Shunt Active Power Filter for Various Reference Current Generation Techniques

Authors: Vishal V. Choudhari, Gaurao A. Dongre, S. P. Diwan

Abstract:

A number of reference current generation have been developed for analysis of shunt active power filter to mitigate the load compensation. Depending upon the type of load the technique has to be chosen. In this paper, six reference current generation techniques viz. instantaneous reactive power theory(IRP), Synchronous reference frame theory(SRF), Perfect harmonic cancellation(PHC), Unity power factor method(UPF), Self-tuning filter method(STF), Predictive filtering method(PFM) are compared for different operating conditions. The harmonics are introduced because of non-linear loads in the system. These harmonics are eliminated using above techniques. The results and performance of system simulated on MATLAB/Simulink platform. The system is experimentally implemented using DS1104 card of dSPACE system.

Keywords: SAPF, power quality, THD, IRP, SRF, dSPACE module DS1104

Procedia PDF Downloads 588
4738 The Reintegration of the Past as Self-Realisation

Authors: Haotian Wu

Abstract:

This article examines the figure Zhao Tao in Jia Zhangke’s films in light of Carl Jung’s psychoanalytical theory. Zhao is a recurring aesthetic trope in Jia’s films, and the characters she plays often have an intimate relationship with the past. Nevertheless, this relationship has not been systematically investigated, especially its symbolism of the typical relationship between the past and the self in post-social China. To fill this research gap, the article will explore how Zhao’s characters discover, preserve, and adapt the past in I Wish I knew (2010), Mountains May Depart (2015), and Ash Is Purest White (2018). Through a Jungian lens, these three levels of engagement with the past will be demonstrated as corresponding with Jung’s psychoanalytical theory of self-realisation, which entails the confrontation with the shadow, the embodiment of the archetype, and individuation. Thus, by articulating a film-philosophy dialogue between Jia and Jung, this article will develop a new philosophy of self-realisation based on the symbolism of Zhao. Through the reintegration of the past, the individuals can overcome the fragmentation of temporality and selfhood in the postmodern world and achieve self-realisation.

Keywords: Jia Zhangke, Jung, psychoanalysis, self-realisation

Procedia PDF Downloads 593
4737 Teachers and Innovations in Information and Communication Technology

Authors: Martina Manenova, Lukas Cirus

Abstract:

This article introduces research focused on elementary school teachers’ approach to innovations in ICT. The diffusion of innovations theory, which was written by E. M. Rogers, captures the processes of innovation adoption. The research method derived from this theory and the Rogers’ questionnaire focused on the diffusion of innovations was used as the basic research method. The research sample consisted of elementary school teachers. The comparison of results with the Rogers’ results shows that among the teachers in the research sample the so-called early majority, as well as the overall division of the data, was rather central (early adopter, early majority, and later majority). The teachers very rarely appeared on the edge positions (innovator, laggard). The obtained results can be applied to teaching practice and used especially in the implementation of new technologies and techniques into the educational process.

Keywords: innovation, diffusion of innovation, information and communication technology, teachers

Procedia PDF Downloads 289
4736 Spiritual Recovery of People with Bipolar Disorder in Malaysia: A Grounded Theory Study

Authors: Mohamad Shariff Nurasikin, Paul Crawford, Nicola Wright

Abstract:

People with any mental disorder can get benefit from the spiritual aspects of life for recovery, particularly in searching for the meaning of life and engaging in meaningful activities. However, little is known about such effects in the population of bipolar disorder. The concepts of spirituality are highly contestable, as they are too broad and removed from the original religious understanding. The concepts are more notable as encompassing multi-dimensional aspects of people’s lives such as social, emotional, and psychological. Viewing that Western or secular worldview dominates most of the literature in spirituality, it is time to explore the concept of spirituality from the Eastern and religious worldview, such as the Malaysian view. Thus, the aim of this study is to provide a conceptual understanding of people with bipolar disorder with a religious affiliation in Malaysia. This study employs a Grounded Theory and explores the narratives from the interviews of 25 participants. The narratives strongly suggest the salient resources or can be referred to as various forms of capital, as in the capital theory, namely, religious, social, psychological, and medicinal. More important is how these capitals are the enablers for recovery in mental health and well-being, where the participants in the sample engage in a more meaningful life and positive adaptations. This study also extends the Bourdieusian spiritual capital, in which the salient resources are termed as the capital bundle. More significant is how the capital bundles are working contiguously in building and accumulating the spiritual capital. This process is conducive to recovery within the social life of people with bipolar disorder or perhaps other mental disorders.

Keywords: bipolar, Bourdeau, recovery, spiritual

Procedia PDF Downloads 383
4735 Balancing Rule of Law, Human Rights and Governance

Authors: Torkan Jabbariraad

Abstract:

This study explores the role of private regulation as a mode of governance that engages non-state actors in establishing and implementing rules or standards for public goods or services. It examines the various forms, functions, and effects of private regulation on the rule of law and human rights and considers the role and duties of public authorities in monitoring and supporting private regulation. It contends that private regulation should be regarded as a beneficial supplement to public regulation rather than a substitute or rival and that public authorities should find a balance between acknowledging the independence and variety of private actors and securing their accountability and legitimacy. It also recommends that applying the principles and values of good governance to private regulation can improve its quality and efficiency. The study relies on various sources and viewpoints from the literature on governance theory, public law, and human rights and suggests further research and discussion on the topic of private regulation and its consequences for society.

Keywords: private regulation, public authority, governance theory, rule of law, human rights

Procedia PDF Downloads 40
4734 The Reasons and the Practical Benefits Behind the Motivation of Businesses to Participate in the Dual Education System (DLS)

Authors: Ainur Bulasheva

Abstract:

During the last decade, the dual learning system (DLS) has been actively introduced in various industries in Kazakhstan, including both vocational, post-secondary, and higher education levels. It is a relatively new practice-oriented approach to training qualified personnel in Kazakhstan, officially introduced in 2012. Dual learning was integrated from the German vocational education and training system, combining practical training with part-time work in production and training in an educational institution. The policy of DLS has increasingly focused on decreasing youth unemployment and the shortage of mid-level professionals by providing incentives for employers to involve in this system. By participating directly in the educational process, the enterprise strives to train its future personnel to meet fast-changing market demands. This study examines the effectiveness of DLS from the perspective of employers to understand the motivations of businesses to participate (invest) in this program. The human capital theory of Backer, which predicts that employers will invest in training their workers (in our case, dual students) when they expect that the return on investment will be greater than the cost - acts as a starting point. Further extensionists of this theory will be considered to understand investing intentions of businesses. By comparing perceptions of DLS employers and non-dual practices, this study determines the efficiency of promoted training approach for enterprises in the Kazakhstan agri-food industry.

Keywords: vocational and technical education, dualeducation, human capital theory, argi-food industry

Procedia PDF Downloads 69
4733 Assessing the Perceptions toward the Impacts of Tourism in Poverty Alleviation: A Basis for Pro-Poor Tourism Policy in Sta. Lucia, Guimba, Nueva Ecija

Authors: Lady Salvador Purganan, Jojo M. Villamin, Noel L. Lansang

Abstract:

Tourism is a multifaceted but interdependent industry. This industry is composed of four major players, the public sector, the private sector, the local community, and the tourists. Each player has a vital role in the success of delivering high-quality tourism products and activities. There are various manifestations of positive economic outcomes that benefit the local community. Pro-poor tourism development approach has a great potential to serve as an avenue for capacity building leading to economic independence since natural attractions and cultural resources are assets that can be capitalized on, especially by the poor, because it is more accessible to them compared to financial resources. In the National Tourism Development Plan 2016-2022, specific mechanisms are not reflected to combat and lower poverty incidence through tourism. The researcher used the multidimensional poverty theory and sustainable tourism theory to formulate indicators in the research instrument and social exchange theory. The expected output of the study is to unlock opportunities, specifically in Brgy. Sta. Lucia, Guimba, Nueva Ecija, by crafting policies taking into utmost consideration local community involvement and participation in the process of tourism development which is essential in attaining inclusive growth and sustainability. This study will apply the sequential explanatory design mixed-method approach.

Keywords: pro-poor tourism, poverty alleviation, livelihood opportunities, tourism development plan

Procedia PDF Downloads 100
4732 The Cross-cultural Adaptation Experience of Foreign Scholars in China

Authors: Jiexiu Chen

Abstract:

This research aims to examine several vital issues relating to the foreign scholars’ cross-cultural adaptation in China, including how they perceive about the adaptation process, what the affecting factors are in the adaptation, and which strategies they will apply to deal with perceived cultural differences. The target population of this research is academics regularly working or long-term visiting in these joint colleges, and semi-structured interviews are used in data collection. Moreover, the theoretical perspectives mainly include Ward’s sociocultural and psychological adaptation theory, Berry’s adaptation strategies and Black and his colleague’s expatriate’s adjustment model. This research offers an in-depth profile as well as theory-based analysis about this unique group, and the results of this research are profound in offering directory suggestions for foreign scholars to facilitate their adaptation in China better and for the Chinese universities to eliminate intercultural obstacles, and optimize the international cooperation programs in China.

Keywords: cross-cultural adaptation, foreign scholars, expatriates

Procedia PDF Downloads 422
4731 The Relationship between Hot and Cool Executive Function and Theory of Mind in School-Aged Children with Autism Spectrum Disorder

Authors: Evangelia-Chrysanthi Kouklari, Stella Tsermentseli, Claire P. Monks

Abstract:

Executive function (EF) refers to a set of future-oriented and goal-directed cognitive skills that are crucial for problem solving and social behaviour, as well as the ability to organise oneself. It has been suggested that EF could be conceptualised as two distinct but interrelated constructs, one emotional (hot) and one cognitive (cool), as it facilitates both affective and cognitive regulation. Cool EF has been found to be strongly related to Theory of Mind (ToM) that is the ability to infer mental states, but research has not taken into account the association between hot EF and ToM in Autism Spectrum Disorder (ASD) to date. The present study investigates the associations between both hot and cool EF and ToM in school-aged children with ASD. This cross-sectional study assesses 79 school-aged children with ASD (7-15 years) and 91 controls matched for age and IQ, on tasks tapping cool EF (working memory, inhibition, planning), hot EF (effective decision making, delay discounting), and ToM (emotional understanding and false/no false belief). Significant group differences in each EF measure support a global executive dysfunction in ASD. Strong associations between hot EF and ToM in ASD are reported for the first time (i.e. ToM emotional understanding and delay discounting). These findings highlight that hot EF also makes a unique contribution to the developmental profile of ASD. Considering the role of both hot and cool EF in association with ToM in individuals with ASD may aid in gaining a greater understanding not just of how these complex multifaceted cognitive abilities relate to one another, but their joint role in the distinct developmental pathway followed in ASD.

Keywords: ASD, executive function, school age, theory of mind

Procedia PDF Downloads 289
4730 Mathematics Bridging Theory and Applications for a Data-Driven World

Authors: Zahid Ullah, Atlas Khan

Abstract:

In today's data-driven world, the role of mathematics in bridging the gap between theory and applications is becoming increasingly vital. This abstract highlights the significance of mathematics as a powerful tool for analyzing, interpreting, and extracting meaningful insights from vast amounts of data. By integrating mathematical principles with real-world applications, researchers can unlock the full potential of data-driven decision-making processes. This abstract delves into the various ways mathematics acts as a bridge connecting theoretical frameworks to practical applications. It explores the utilization of mathematical models, algorithms, and statistical techniques to uncover hidden patterns, trends, and correlations within complex datasets. Furthermore, it investigates the role of mathematics in enhancing predictive modeling, optimization, and risk assessment methodologies for improved decision-making in diverse fields such as finance, healthcare, engineering, and social sciences. The abstract also emphasizes the need for interdisciplinary collaboration between mathematicians, statisticians, computer scientists, and domain experts to tackle the challenges posed by the data-driven landscape. By fostering synergies between these disciplines, novel approaches can be developed to address complex problems and make data-driven insights accessible and actionable. Moreover, this abstract underscores the importance of robust mathematical foundations for ensuring the reliability and validity of data analysis. Rigorous mathematical frameworks not only provide a solid basis for understanding and interpreting results but also contribute to the development of innovative methodologies and techniques. In summary, this abstract advocates for the pivotal role of mathematics in bridging theory and applications in a data-driven world. By harnessing mathematical principles, researchers can unlock the transformative potential of data analysis, paving the way for evidence-based decision-making, optimized processes, and innovative solutions to the challenges of our rapidly evolving society.

Keywords: mathematics, bridging theory and applications, data-driven world, mathematical models

Procedia PDF Downloads 75
4729 Functional Performance of Unpaved Roads Reinforced with Treated Coir Geotextiles

Authors: Priya Jaswal, Vivek, S. K. Sinha

Abstract:

One of the most important and complicated factors influencing the functional performance of unpaved roads is traffic loading. The complexity of traffic loading is caused by the variable magnitude and frequency of load, which causes unpaved roads to fail prematurely. Unpaved roads are low-volume roads, and as peri-urbanization increases, unpaved roads act as a means to boost the rural economy. This has also increased traffic on unpaved roads, intensifying the issue of settlement, rutting, and fatigue failure. This is a major concern for unpaved roads built on poor subgrade soil, as excessive rutting caused by heavy loads can cause driver discomfort, vehicle damage, and an increase in maintenance costs. Some researchers discovered that when a consistent static load is exerted as opposed to a rapidly changing load, the rate of deformation of unpaved roads increases. Previously, some of the most common methods for overcoming the problem of rutting and fatigue failure included chemical stabilisation, fibre reinforcement, and so on. However, due to their high cost, engineers' attention has shifted to geotextiles which are used as reinforcement in unpaved roads. Geotextiles perform the function of filtration, lateral confinement of base material, vertical restraint of subgrade soil, and the tension membrane effect. The use of geotextiles in unpaved roads increases the strength of unpaved roads and is an economically viable method because it reduces the required aggregate thickness, which would need less earthwork, and is thus recommended for unpaved road applications. The majority of geotextiles used previously were polymeric, but with a growing awareness of sustainable development to preserve the environment, researchers' focus has shifted to natural fibres. Coir is one such natural fibre that possesses the advantage of having a higher tensile strength than other bast fibres, being eco-friendly, low in cost, and biodegradable. However, various researchers have discovered that the surface of coir fibre is covered with various impurities, voids, and cracks, which act as a plane of weakness and limit the potential application of coir geotextiles. To overcome this limitation, chemical surface modification of coir geotextiles is widely accepted by researchers because it improves the mechanical properties of coir geotextiles. The current paper reviews the effect of using treated coir geotextiles as reinforcement on the load-deformation behaviour of a two-layered unpaved road model.

Keywords: coir, geotextile, treated, unpaved

Procedia PDF Downloads 91
4728 A CFD Analysis of Flow through a High-Pressure Natural Gas Pipeline with an Undeformed and Deformed Orifice Plate

Authors: R. Kiš, M. Malcho, M. Janovcová

Abstract:

This work aims to present a numerical analysis of the natural gas which flows through a high-pressure pipeline and an orifice plate, through the use of CFD methods. The paper contains CFD calculations for the flow of natural gas in a pipe with different geometry used for the orifice plates. One of them has a standard geometry and a shape without any deformation and the other is deformed by the action of the pressure differential. It shows the behaviour of natural gas in a pipeline using the velocity profiles and pressure fields of the gas in both models with their differences. The entire research is based on the elimination of any inaccuracy which should appear in the flow of the natural gas measured in the high-pressure pipelines of the gas industry and which is currently not given in the relevant standard.

Keywords: orifice plate, high-pressure pipeline, natural gas, CFD analysis

Procedia PDF Downloads 377
4727 Omani PE Candidate Self-Reports of Learning Strategies Used to Learn Sport Skills

Authors: Nasser Al-Rawahi

Abstract:

The study aims at determining self-regulated learning strategies used by Omani physical education candidates to learn sport skills. The data were collected by a self-regulated learning theory questionnaire. The sample of the study comprised of 145 undergraduate physical education students enrolled in the department of physical education at the College of Education, Sultan Qaboos University. The findings of the study revealed that the most commonly used strategies for learning sport skills by Omani physical education candidate are ‘the effort learning strategies, planning learning strategies and evaluation learning strategies’. However, the reflection learning strategies, self-monitoring and self-efficacy learning strategies were revealed as the least used strategies by the PE candidates in learning and acquiring sport skills. Based on these findings, suggestions and recommendations for future research were provided.

Keywords: learning strategies, physical education candidates, self-regulated learning theory, Oman

Procedia PDF Downloads 613
4726 Flow of a Second Order Fluid through Constricted Tube with Slip Velocity at Wall Using Integral Method

Authors: Nosheen Zareen Khan, Abdul Majeed Siddiqui, Muhammad Afzal Rana

Abstract:

The steady flow of a second order fluid through constricted tube with slip velocity at wall is modeled and analyzed theoretically. The governing equations are simplified by implying no slip in radial direction. Based on Karman Pohlhausen procedure polynomial solution for axial velocity profile is presented. An expressions for pressure gradient, shear stress, separation and reattachment points and radial velocity are also calculated. The effect of slip and no slip velocity on velocity, shear stress, pressure gradient are discussed and depicted graphically. It is noted that when Reynolds number increases velocity of the fluid decreases in both slip and no slip conditions. It is also found that the wall shear stress, separation and reattachment points are strongly effected by Reynolds number.

Keywords: approximate solution, constricted tube, non-Newtonian fluids, Reynolds number

Procedia PDF Downloads 397
4725 A Fundamental Study for Real-Time Safety Evaluation System of Landing Pier Using FBG Sensor

Authors: Heungsu Lee, Youngseok Kim, Jonghwa Yi, Chul Park

Abstract:

A landing pier is subjected to safety assessment by visual inspection and design data, but it is difficult to check the damage in real-time. In this study, real - time damage detection and safety evaluation methods were studied. As a result of structural analysis of the arbitrary landing pier structure, the inflection point of deformation and moment occurred at 10%, 50%, and 90% of pile length. The critical value of Fiber Bragg Grating (FBG) sensor was set according to the safety factor, and the FBG sensor application method for real - time safety evaluation was derived.

Keywords: FBG sensor, harbor structure, maintenance, safety evaluation system

Procedia PDF Downloads 216
4724 Layout Design Optimization of Spars under Multiple Load Cases of the High-Aspect-Ratio Wing

Authors: Yu Li, Jingwu He, Yuexi Xiong

Abstract:

The spar layout will affect the wing’s stiffness characteristics, and irrational spar arrangement will reduce the overall bending and twisting resistance capacity of the wing. In this paper, the active structural stiffness design theory is used to match the stiffness-center axis position and load-cases under the corresponding multiple flight conditions, in order to achieve better stiffness properties of the wing. The combination of active stiffness method and principle of stiffness distribution is proved to be reasonable supplying an initial reference for wing designing. The optimized layout of spars is eventually obtained, and the high-aspect-ratio wing will have better stiffness characteristics.

Keywords: active structural stiffness design theory, high-aspect-ratio wing, flight load cases, layout of spars

Procedia PDF Downloads 320
4723 Gendered Perspectives on the Understanding of the Politics and the Social Life

Authors: Canan Cetin

Abstract:

This essay analyses how gendered shaped views influence on our understanding of global politics. To do so, feminism used as a framework theory, thus masculinity is discussed in order to explain the male-dominated international relations (IR) discipline and the differences of reflections on our perspective considering the politics in a broader perspective. Particularly, it is highlighted that the social and cultural structures of societies have also an impact on our views about international relations and politics. From a different perspective, it is aimed that the sociological and cultural impression of the shifted gender perspectives on the political approach of different nations and societies will be examined by drawing on a range of sources. Instead of supporting one feminist theory, this essay engages with all traditions and enriches their arguments. Specifically, the main objective of the essay is hegemonic and plural masculinity on societies. The essay sets things up theoretically by looking at the nature of masculinity – the stage is set to show how this informs our understanding of IR.

Keywords: feminism, politics, international affairs, social life

Procedia PDF Downloads 202
4722 Development of Graph-Theoretic Model for Ranking Top of Rail Lubricants

Authors: Subhash Chandra Sharma, Mohammad Soleimani

Abstract:

Selection of the correct lubricant for the top of rail application is a complex process. In this paper, the selection of the proper lubricant for a Top-Of-Rail (TOR) lubrication system based on graph theory and matrix approach has been developed. Attributes influencing the selection process and their influence on each other has been represented through a digraph and an equivalent matrix. A matrix function which is called the Permanent Function is derived. By substituting the level of inherent contribution of the influencing parameters and their influence on each other qualitatively, a criterion called Suitability Index is derived. Based on these indices, lubricants can be ranked for their suitability. The proposed model can be useful for maintenance engineers in selecting the best lubricant for a TOR application. The proposed methodology is illustrated step–by-step through an example.

Keywords: lubricant selection, top of rail lubrication, graph-theory, Ranking of lubricants

Procedia PDF Downloads 293
4721 Evaluation of River Meander Geometry Using Uniform Excess Energy Theory and Effects of Climate Change on River Meandering

Authors: Youssef I. Hafez

Abstract:

Since ancient history rivers have been the fostering and favorite place for people and civilizations to live and exist along river banks. However, due to floods and droughts, especially sever conditions due to global warming and climate change, river channels are completely evolving and moving in the lateral direction changing their plan form either through straightening of curved reaches (meander cut-off) or increasing meandering curvature. The lateral shift or shrink of a river channel affects severely the river banks and the flood plain with tremendous impact on the surrounding environment. Therefore, understanding the formation and the continual processes of river channel meandering is of paramount importance. So far, in spite of the huge number of publications about river-meandering, there has not been a satisfactory theory or approach that provides a clear explanation of the formation of river meanders and the mechanics of their associated geometries. In particular two parameters are often needed to describe meander geometry. The first one is a scale parameter such as the meander arc length. The second is a shape parameter such as the maximum angle a meander path makes with the channel mean down path direction. These two parameters, if known, can determine the meander path and geometry as for example when they are incorporated in the well known sine-generated curve. In this study, a uniform excess energy theory is used to illustrate the origin and mechanics of formation of river meandering. This theory advocates that the longitudinal imbalance between the valley and channel slopes (with the former is greater than the second) leads to formation of curved meander channel in order to reduce the excess energy through its expenditure as transverse energy loss. Two relations are developed based on this theory; one for the determination of river channel radius of curvature at the bend apex (shape parameter) and the other for the determination of river channel sinuosity. The sinuosity equation tested very well when applied to existing available field data. In addition, existing model data were used to develop a relation between the meander arc length and the Darcy-Weisback friction factor. Then, the meander wave length was determined from the equations of the arc length and the sinuosity. The developed equation compared well with available field data. Effects of the transverse bed slope and grain size on river channel sinuosity are addressed. In addition, the concept of maximum channel sinuosity is introduced in order to explain the changes of river channel plan form due to changes in flow discharges and sediment loads induced by global warming and climate changes.

Keywords: river channel meandering, sinuosity, radius of curvature, meander arc length, uniform excess energy theory, transverse energy loss, transverse bed slope, flow discharges, sediment loads, grain size, climate change, global warming

Procedia PDF Downloads 223
4720 The Big Bang Was Not the Beginning, but a Repeating Pattern of Expansion and Contraction of the Spacetime

Authors: Amrit Ladhani

Abstract:

The cyclic universe theory is a model of cosmic evolution according to which the universe undergoes endless cycles of expansion and cooling, each beginning with a “big bang” and ending in a “big crunch”. In this paper, we propose a unique property of Space-time. This particular and marvelous nature of space shows us that space can stretch, expand, and shrink. This property of space is caused by the size of the universe change over time: growing or shrinking. The observed accelerated expansion, which relates to the stretching of Shrunk space for the new theory, is derived. This theory is based on three underlying notions: First, the Big Bang is not the beginning of Space-time, but rather, at the very beginning fraction of a second, there was an infinite force of infinite Shrunk space in the cosmic singularity that force gave rise to the big bang and caused the rapidly growing of space, and all other forms of energy are transformed into new matter and radiation and a new period of expansion and cooling begins. Second, there was a previous phase leading up to it, with multiple cycles of contraction and expansion that repeat indefinitely. Third, the two principal long-range forces are the gravitational force and the repulsive force generated by shrink space. They are the two most fundamental quantities in the universe that govern cosmic evolution. They may provide the clockwork mechanism that operates our eternal cyclic universe. The universe will not continue to expand forever; no need, however, for dark energy and dark matter. This new model of Space-time and its unique properties enables us to describe a sequence of events from the Big Bang to the Big Crunch.

Keywords: dark matter, dark energy, cosmology, big bang and big crunch

Procedia PDF Downloads 78
4719 Design of Reconfigurable Supernumerary Robotic Limb Based on Differential Actuated Joints

Authors: Qinghua Zhang, Yanhe Zhu, Xiang Zhao, Yeqin Yang, Hongwei Jing, Guoan Zhang, Jie Zhao

Abstract:

This paper presents a wearable reconfigurable supernumerary robotic limb with differential actuated joints, which is lightweight, compact and comfortable for the wearers. Compared to the existing supernumerary robotic limbs which mostly adopted series structure with large movement space but poor carrying capacity, a prototype with the series-parallel configuration to better adapt to different task requirements has been developed in this design. To achieve a compact structure, two kinds of cable-driven mechanical structures based on guide pulleys and differential actuated joints were designed. Moreover, two different tension devices were also designed to ensure the reliability and accuracy of the cable-driven transmission. The proposed device also employed self-designed bearings which greatly simplified the structure and reduced the cost.

Keywords: cable-driven, differential actuated joints, reconfigurable, supernumerary robotic limb

Procedia PDF Downloads 219
4718 The Translation of Code-Switching in African Literature: Comparing the Two German Translations of Ngugi Wa Thiongo’s "Petals of Blood"

Authors: Omotayo Olalere

Abstract:

The relevance of code-switching for intercultural communication through literary translation cannot be overemphasized. The translation of code-switching and its implications for translations studies have been studied in the context of African literature. In these cases, code-switching was examined in the more general terms of its usage in source text and not particularly in Ngugi’s novels and its translations. In addition, the functions of translation and code-switching in the lyrics of some popular African songs have been studied, but this study is related more with oral performance than with written literature. As such, little has been done on the German translation of code-switching in African works. This study intends to fill this lacuna by examining the concept of code-switching in the German translations in Ngugi’s Petals of Blood. The aim is to highlight the significance of code-switching as a phenomenon in this African (Ngugi’s) novel written in English and to also focus on its representation in the two German translations. The target texts to be used are Verbrannte Blueten and Land der flammenden Blueten. “Abrogration“ as a concept will play an important role in the analysis of the data. Findings will show that the ideology of a translator plays a huge role in representing the concept of “abrogration” in the translation of code-switching in the selected source text. The study will contribute to knowledge in translation studies by bringing to limelight the need to foreground aspects of language contact in translation theory and practice, particularly in the African context. Relevant translation theories adopted for the study include Bandia’s (2008) postcolonial theory of translation and Snell-Hornby”s (1988) cultural translation theory.

Keywords: code switching, german translation, ngugi wa thiong’o, petals of blood

Procedia PDF Downloads 90
4717 The Aspect of the Human Bias in Decision Making within Quality Management Systems and LEAN Theory

Authors: Adriana Avila Zuniga Nordfjeld

Abstract:

This paper provides a literature review to document the state of the art with respect to handling 'human bias' in decision making within the established quality management systems (QMS) and LEAN theory, in the context of shipbuilding. Previous research shows that in shipbuilding there is a huge deviation from the planned man-hours under the project management to the actual man-hours used because of errors in planning and reworks caused by human bias in the information flows among others. This reduces the efficiency and increases operational costs. Thus, the research question is how QMS and LEAN handle biases. The findings show the gap in studying the integration of methods to handle human bias in decision making into QMS and lean, not only within shipbuilding but also in general. Theoretical and practical implications are discussed for researchers and practitioners in the areas of decision making QMS, LEAN, and future research is suggested.

Keywords: human bias, decision making, LEAN shipbuilding, quality management systems

Procedia PDF Downloads 546
4716 Freud’s Theories: Lie or a Symbolism

Authors: Aakriti Lohiya

Abstract:

Sigmund Freud’s clinical theories were deeply influenced by his childhood and his environment before his exile in England. In this article, the author illuminates his different works and the metaphors in them. The clinical relevance of Freud’s theories is much disputed and chatted but rarely has any psychoanalytic writing touched upon the way in which his theories are linked with life experiences. Exploring the metaphors in Freud’s theories will take us into the uncharted paths of how the experience of life events meets experience in the clinic. A sincere and critical reflection of the ideas proposed by Freud would certainly help us to locate its unfamiliar stages. Many of his theories and ideas attempted to create contact with his early childhood experiences. Freud was Jewish by birth but atheist by nature, which was reflected in many of his theories. The ways in which Freud theorizes the psychosexual development of a being and many of his mammoth theories are elucidated in this study. On the other hand, some of his ideas remain a challenge, which requires remembering, restating, and functioning through the clinical and mystical elements in his writing.

Keywords: sigmund freud, exile, psychoanalytic theory, metaphor, psychosexual theory

Procedia PDF Downloads 70
4715 Place-Making Theory behind Claremont Court

Authors: Sandra Costa-Santos, Nadia Bertolino, Stephen Hicks, Vanessa May, Camilla Lewis

Abstract:

This paper aims to elaborate the architectural theory on place-making that supported Claremont Court housing scheme (Edinburgh, United Kingdom). Claremont Court (1959-62) is a large post-war mixed development housing scheme designed by Basil Spence, which included ‘place-making’ as one of its founding principles. Although some stylistic readings of the housing scheme have been published, the theory on place-making that allegedly ruled the design has yet to be clarified. The architecture allows us to mark or make a place within space in order to dwell. Under the framework of contemporary philosophical theories of place, this paper aims to explore the relationship between place and dwelling through a cross-disciplinary reading of Claremont Court, with a view to develop an architectural theory on place-making. Since dwelling represents the way we are immersed in our world in an existential manner, this theme is not just relevant for architecture but also for philosophy and sociology. The research in this work is interpretive-historic in nature. It examines documentary evidence of the original architectural design, together with relevant literature in sociology, history, and architecture, through the lens of theories of place. First, the paper explores how the dwelling types originally included in Claremont Court supported ideas of dwelling or meanings of home. Then, it traces shared space and social ties in order to study the symbolic boundaries that allow the creation of a collective identity or sense of belonging. Finally, the relation between the housing scheme and the supporting theory is identified. The findings of this research reveal Scottish architect Basil Spence’s exploration of the meaning of home, as he changed his approach to the mass housing while acting as President of the Royal Incorporation of British Architects (1958-60). When the British Government was engaged in various ambitious building programmes, he sought to drive architecture to a wider socio-political debate as president of the RIBA, hence moving towards a more ambitious and innovative socio-architectural approach. Rather than trying to address the ‘genius loci’ with an architectural proposition, as has been stated, the research shows that the place-making theory behind the housing scheme was supported by notions of community-based on shared space and dispositions. The design of the housing scheme was steered by a desire to foster social relations and collective identities, rather than by the idea of keeping the spirit of the place. This research is part of a cross-disciplinary project funded by the Arts and Humanities Research Council. The findings present Claremont Court as a signifier of Basil Spence’s attempt to address the post-war political debate on housing in United Kingdom. They highlight the architect’s theoretical agenda and challenge current purely stylistic readings of Claremont Court as they fail to acknowledge its social relevance.

Keywords: architectural theory, dwelling, place-making, post-war housing

Procedia PDF Downloads 265
4714 A Comparative Evaluation of Stone Spout Management Systems in Heritage and Non-heritage Areas of the Kathmandu Valley, Nepal

Authors: Mira Tripathi, Ken Hughey, Hamish G. Rennie

Abstract:

Management of water resources is a major challenge throughout the world and in many long-established societies people still use traditional water harvesting and management techniques. Despite often being seen as efficient and cost effective, traditional methods are in decline or have been abandoned in many countries. Nevertheless, traditional approaches continue to be useful in some countries such as Nepal. The extent to which such traditional measures, in this case via stone spouts, may survive modernization, while fulfilling socio-cultural, tourism, and other needs is the focus of the research. The research develops an understanding of the socio-cultural, tourism and other values of stone spouts for the people of urban and peri-urban heritage and non-heritage areas of the Kathmandu Valley to help ongoing sustainable management of remaining spouts. Three research questions are addressed: the impacts of changes in social and cultural norms and values; development activities; and, the incremental and ongoing loss of traditional stone spout infrastructure. A meta-theory framework has been developed which synthesizes Institutional, Attachment, Central Place and Common Property theories, which form analytical lenses for the mixed-method research approach. From the exploration of the meta-theory approach, it was found that no spouts are in pristine condition but those in non-heritage areas are in better condition than those in heritage areas. “Utility value” is the main driver that still motivates people to conserve spouts.

Keywords: stone spouts, social and cultural norms and values, meta-theory, Kathmandu Valley

Procedia PDF Downloads 311
4713 Influence of Nanoparticles Phenomena on the Peristaltic Flow of Pseudoplastic Fluid in an Inclined Asymmetric Channel with Different Wave Forms

Authors: Safia Akram

Abstract:

The influence of nanofluid with different waveforms in the presence of inclined asymmetric channel on peristaltic transport of a pseudoplastic fluid is examined. The governing equations for two-dimensional and two directional flows of a pseudoplastic fluid along with nanofluid are modeled and then simplified under the assumptions of long wavelength and low Reynolds number approximation. The exact solutions for temperature and nanoparticle volume fraction are calculated. Series solution of the stream function and pressure gradient are carried out using perturbation technique. The flow quantities have been examined for various physical parameters of interest. It was found, that the magnitude value of the velocity profile decreases with an increase in volume flow rate (Q) and relaxation times (ζ) and increases in sinusoidal, multisinusoidal, trapezoidal and triangular waves. It was also observed that the size of the trapping bolus decreases with the drop of the width of the channel ‘d’ and increases with a rise of relaxation times ζ.

Keywords: nanofluid particles, peristaltic flow, pseudoplastic fluid, different waveforms, inclined asymmetric channel

Procedia PDF Downloads 236
4712 Dynamic Two-Way FSI Simulation for a Blade of a Small Wind Turbine

Authors: Alberto Jiménez-Vargas, Manuel de Jesús Palacios-Gallegos, Miguel Ángel Hernández-López, Rafael Campos-Amezcua, Julio Cesar Solís-Sanchez

Abstract:

An optimal wind turbine blade design must be able of capturing as much energy as possible from the wind source available at the area of interest. Many times, an optimal design means the use of large quantities of material and complicated processes that make the wind turbine more expensive, and therefore, less cost-effective. For the construction and installation of a wind turbine, the blades may cost up to 20% of the outline pricing, and become more important due to they are part of the rotor system that is in charge of transmitting the energy from the wind to the power train, and where the static and dynamic design loads for the whole wind turbine are produced. The aim of this work is the develop of a blade fluid-structure interaction (FSI) simulation that allows the identification of the major damage zones during the normal production situation, and thus better decisions for design and optimization can be taken. The simulation is a dynamic case, since we have a time-history wind velocity as inlet condition instead of a constant wind velocity. The process begins with the free-use software NuMAD (NREL), to model the blade and assign material properties to the blade, then the 3D model is exported to ANSYS Workbench platform where before setting the FSI system, a modal analysis is made for identification of natural frequencies and modal shapes. FSI analysis is carried out with the two-way technic which begins with a CFD simulation to obtain the pressure distribution on the blade surface, then these results are used as boundary condition for the FEA simulation to obtain the deformation levels for the first time-step. For the second time-step, CFD simulation is reconfigured automatically with the next time-step inlet wind velocity and the deformation results from the previous time-step. The analysis continues the iterative cycle solving time-step by time-step until the entire load case is completed. This work is part of a set of projects that are managed by a national consortium called “CEMIE-Eólico” (Mexican Center in Wind Energy Research), created for strengthen technological and scientific capacities, the promotion of creation of specialized human resources, and to link the academic with private sector in national territory. The analysis belongs to the design of a rotor system for a 5 kW wind turbine design thought to be installed at the Isthmus of Tehuantepec, Oaxaca, Mexico.

Keywords: blade, dynamic, fsi, wind turbine

Procedia PDF Downloads 480