Search results for: factors influencing project selection

Authors: Iyad Al-Attar

Abstract:

Air filters are widely used in gas turbines applications to ensure that the large mass (500kg/s) of clean air reach the compressor. The continuous demand of high availability and reliability has highlighted the critical role of air filter performance in providing enhanced air quality. In addition to being challenged with different environments [tropical, coastal, hot], gas turbines confront wide array of atmospheric contaminants with various concentrations and particle size distributions that would lead to performance degradation and components deterioration. Therefore, the role of air filters is of a paramount importance since fouled compressor can reduce power output and availability of the gas turbine to over 70 % throughout operation. Consequently, accurate filter performance prediction is critical tool in their selection considering their role in minimizing the economic impact of outages. In fact, actual performance of Efficient Particulate Air [EPA] filters used in gas turbine tend to deviate from the performance predicted by laboratory results. This experimental work investigates the initial pressure drop and fractional efficiency curves of full-scale pleated V-shaped EPA filters used globally in gas turbine. The investigation involved examining the effect of different operational conditions such as flow rates [500 to 5000 m3/h] and design parameters such as pleat count [28, 30, 32 and 34 pleats per 100mm]. This experimental work has highlighted the underlying reasons behind the reduction in filter permeability due to the increase of flow rates and pleat density. The reasons, which led to surface area losses of filtration media, are due to one or combination of the following effects: pleat-crowding, deflection of the entire pleated panel, pleat distortion at the corner of the pleat and/or filtration medium compression. This paper also demonstrates that the effect of increasing the flow rate has more pronounced effect on filter performance compared to pleating density. This experimental work suggests that a valid comparison of the pleat densities should be based on the effective surface area, namely, the area that participates in the filtration process, and not the total surface area the pleat density provides. Throughout this study, optimal pleat count that satisfies both initial pressure drop and efficiency requirements may not have necessarily existed.

Keywords: filter efficiency, EPA Filters, pressure drop, permeability

Procedia PDF Downloads 226

Authors: Nivedita Roy, Aparajita Chattopadhyay

Abstract:

Gender discrimination is already one of the major factors why India is still in the list of the 3rd World Countries, but, when it comes to gender inclusion in the environmental arena, this umbrella concept is quite unheard of by our countrymen. The main objective was to assess gender equality for the environment through calculating Environment and Gender Index on a country level, India, in this case. 22 states out of 29 were considered for calculation. Also, out of the 72 countries chosen by IUCN to calculate EGI, the lower middle income group of countries was chosen to assess the position of India, also a lower middle income group country, among them. Linear Regression is executed through SPSS and simple graphs and tables are prepared through MS-EXCEL for analysis. India portrays good governance, reporting activities well to the UN but in terms of basic livelihood and gender equality, the performance is comparatively weak.

Keywords: environment, gender, livelihood, rights, participation, development, conservation

Procedia PDF Downloads 428

Authors: Alina P. Colling, Robert G. Hekkenberg

Abstract:

Recent years have seen extensive technological advancement in truck platooning, as reflected in the literature. Its main benefits are the improvement of traffic stability and the reduction of air drag, resulting in less fuel consumption, in comparison to using individual trucks. Platooning is now being adapted to the waterborne transport sector in the NOVIMAR project through the development of a Vessel Train (VT) concept. The main focus of VT’s, as opposed to the truck platoons, is the decrease in manning on board, ultimately working towards autonomous vessel operations. This crew reduction can prove to be an important selling point in achieving economic competitiveness of the waterborne approach when compared to alternative modes of transport. This paper discusses the expected benefits and drawbacks of the VT concept, in terms of the technical logistic performance and generalized costs. More specifically, VT’s can provide flexibility in destination choices for shippers but also add complexity when performing special manoeuvres in VT formation. In order to quantify the cost and performances, a model is developed and simulations are carried out for various case studies. These compare the application of VT’s in the short sea and inland water transport, with specific sailing regimes and technologies installed on board to allow different levels of autonomy. The results enable the identification of the most important boundary conditions for the successful operation of the waterborne platooning concept. These findings serve as a framework for future business applications of the VT.

Keywords: autonomous vessels, NOVIMAR, vessel trains, waterborne platooning

Procedia PDF Downloads 206

Authors: Pratik Pankaj Pawar

Abstract:

Lightweight structures - structures with reduced weight, which otherwise retain the qualities necessary for the building performance, ensuring proper durability and strength, safety, indoor environmental quality, and energy efficiency; structures that strive for the optimization of structural systems - are in tune with current trends and socio-economic, environmental, and technological factors. The growing interest in lightweight structures design makes them an ever more significant field of research. This article focuses on the architectural aspects of lightweight structures and on their contemporary and future applications. The selected advanced building technologies - i.e., Ultra-High-Performance Concrete, fabrics, and flexible photovoltaics.

Keywords: light weight building, carbyne, aerographite, geopolymer reinforced wood particles aggregate

Procedia PDF Downloads 36

Authors: Isaiah Phillip Smith

Abstract:

It is reported that alcohol consumption accounts for 3 million annual deaths globally, thus, it is a significant public health challenge internationally. The excessive consumption of alcohol is argued in literature to be related to problematic behaviors like crime, accident, fighting, violence, and unprotected sex, among others. Alcohol consumption among university students in South Africa particularly is considered endemic – with a prevalence rate of 25.27%, 32.34%, and 23.34% across universities, colleges, and high schools. Adopting the tenets of social learning and ecological theories, the culture of drinking amongst male university students is critically explored. This study found that age, gender, early exposure to alcohol, and peer pressure are significant factors contributing to alcohol consumption amongst university students. While participants acknowledged that moderate and responsible consumption of alcohol is necessary, they agree that it does not translate to responsible drinking behaviours.

Keywords: alcohol, drinking, university, students

Procedia PDF Downloads 117

Authors: Gerald Amatre, Julius Bunny Lejju, Morgan Andama

Abstract:

Despite several interventions, jigger flea infestations continue to be reported in the Busoga sub-region in Eastern Uganda. The purpose of this study was to identify factors that expose the indigenous people to jigger flea infestations and evaluate the effectiveness of any indigenous materials used in flea control by the affected communities. Flea compositions in residences were described, factors associated with flea infestation and indigenous materials used in flea control were evaluated. Field surveys were conducted in the affected communities after obtaining preliminary information on jigger infestation from the offices of the District Health Inspectors to identify the affected villages and households. Informed consent was then sought from the local authorities and household heads to conduct the study. Focus group discussions were conducted with key district informants, namely, the District Health Inspectors, District Entomologists and representatives from the District Health Office. A GPS coordinate was taken at central point at every household enrolled. Fleas were trapped inside residences using Kilonzo traps. A Kilonzo Trap comprised a shallow pan, about three centimetres deep, filled to the brim with water. The edges of the pan were smeared with Vaseline to prevent fleas from crawling out. Traps were placed in the evening and checked every morning the following day. The trapped fleas were collected in labelled vials filled with 70% aqueous ethanol and taken to the laboratory for identification. Socio-economic and environmental data were collected. The results indicate that the commonest flea trapped in the residences was the cat flea (Ctenocephalides felis) (50%), followed by Jigger flea (Tunga penetrans) (46%) and rat flea (Xenopsylla Cheopis) (4%), respectively. The average size of residences was seven squire metres with a mean of six occupants. The residences were generally untidy; with loose dusty floors and the brick walls were not plastered. The majority of the jigger affected households were headed by peasants (86.7%) and artisans (13.3%). The household heads mainly stopped at primary school level (80%) and few at secondary school level (20%). The jigger affected households were mainly headed by peasants of low socioeconomic status. The affected community members use soil-cow dung-ash mixture to smear floors of residences as the only measure to control fleas. This method was found to be ineffective in controlling the insects. The study recommends that home improvement campaigns be continued in the affected communities to improve sanitation and hygiene in residences as one of the interventions to combat flea infestations. Other cheap, available and effective means should be identified to curb jigger flea infestations.

Keywords: cow dung-soil-ash mixture, infestations, jigger flea, Tunga penetrans

Procedia PDF Downloads 124

Authors: Fehmeen Anwar, Ujala Liaqat

Abstract:

For over half a century, U.S. and the Soviet Union have been at daggers drawn with each other. Both leading powers of the world have been struggling hard to surpass each other in military and other technological fields. This neck-to-neck competition turned in favour of U.S. in the early 1990s when USSR had to face economic stagnation and later dismemberment of several of its states. The predominance of U.S. is still evident to date, rather it continues to grow. With this proposed defence program i.e. Anti-Ballistic Missile System, the U.S. will have a considerable chance of intercepting any nuclear strike by Russia, which re-asserts U.S. dominance in the region and creating a security dilemma for Russia and other states. The question is whether America’s recent nuclear deterrence project is merely to counter nuclear threats from Iran and North Korea or is it purely directed towards Russia, thus ensuring complete military supremacy in the world. Although U.S professes to direct its Anti-Ballistic Missile System (ABMS) against the axis of evil (Iran and North Korea), yet the deployment of this system in the East European territory undermines the Russian nuclear strategic capability, as this enables U.S. to initiate an attack and guard itself from retaliatory strike, thus disturbing the security equilibrium in Europe. The implications of this program can lead to power imbalance which can lead to the emergence of fundamentally different paradigm of international politics.

Keywords: Anti-Ballistic Missile System (ABMS), cold-war, axis of evil, power dynamics

Procedia PDF Downloads 280

Authors: Sung-Wook Shin, Sung-Taek Chung

Abstract:

Hand grip strength has been utilized as an indicator to evaluate the motor ability of hands, responsible for performing multiple body functions. It is, however, difficult to evaluate other factors (other than hand muscular strength) utilizing the hand grip strength only. In this study, we analyzed the motor ability of hands using EMG and the hand grip strength, simultaneously in order to evaluate concentration, muscular strength reaction time, instantaneous muscular strength change, and agility in response to visual reaction. In results, the average time (and their standard deviations) of muscular strength reaction EMG signal and hand grip strength was found to be 209.6 ± 56.2 ms and 354.3 ± 54.6 ms, respectively. In addition, the onset time which represents acceleration time to reach 90% of maximum hand grip strength, was 382.9 ± 129.9 ms.

Keywords: hand grip strength, EMG, visual reaction, endurance

Procedia PDF Downloads 450

Authors: Vida Razzaghifard

Abstract:

E-learning, also known as online learning, has indicated an increased growth in recent years. One of the critical factors in the successful application of e-learning in higher education is students’ perceptions towards it. The main purpose of this paper is to investigate the perceptions of engineering students about e-learning in UK. For the purpose of the present study, 145 second year Engineering students were randomly selected from the total population of 1280 participants. The participants were asked to complete a questionnaire containing 16 items. The data collected from the questionnaire were analyzed through the Statistical Package for Social Science (SPSS) software. The findings of the study revealed that the majority of participants have negative perceptions on e-learning. Most of the students had trouble interacting effectively during online classes. Furthermore, the majority of participants had negative experiences with the learning platform they used during e-learning. Suggestions were made on what could be done to improve the students’ perceptions towards e-learning.

Keywords: E-learning, higher, education, engineering education, online learning

Procedia PDF Downloads 84

Authors: Noor Ashikin Omar

Abstract:

The rapid growth and advancement in information and communication technology (ICT) at a global scene has greatly influenced and revolutionised interaction amongst society. The use of ICT has become second nature in managing everyday lives, particularly in the education environment. Traditional learning methods of using blackboards and chalks have been largely improved by the use of ICT devices such as interactive whiteboards and computers in school. This paper aims to explore the impacts of virtual learning environments (VLE) on teacher’s pedagogy and student’s learning in primary school settings. The research was conducted in two phases. Phase one of this study comprised a short interview with the school’s senior assistants to examine issues and challenges faced during planning and implementation of FrogVLE in their respective schools. Phase two involved a survey of a number of questionnaires directed to three major stakeholders; the teachers, students and parents. The survey intended to explore teacher’s and student’s perspective and attitude towards the use of VLE as a teaching and learning medium and as a learning experience as a whole. In addition, the survey from parents provided insights on how they feel towards the use of VLE for their child’s learning. Collectively, the two phases enable improved understanding and provided observations on factors that had affected the implementation of the VLE into primary schools. This study offers the voices of the students which were frequently omitted when addressing innovations as well as teachers who may not always be heard. It is also significant in addressing the importance of teacher’s pedagogy on students’ learning and its effects to enable more effective ICT integration with a student-centred approach. Finally, parental perceptions in the implementation of VLE in supporting their children’s learning have been implicated as having a bearing on educational achievement. The results indicate that the all three stakeholders were positive and highly supportive towards the use of VLE in schools. They were able to understand the benefits of moving towards the modern method of teaching using ICT and accept the change in the education system. However, factors such as condition of ICT facilities at schools and homes as well as inadequate professional development for the teachers in both ICT skills and management skills hindered exploitation of the VLE system in order to fully utilise its benefits. Social influences within different communities and cultures and costs of using the technology also has a significant impact. The findings of this study are important to the Malaysian Ministry of Education because it informs policy makers on the impact of the Virtual Learning Environment (VLE) on teacher’s pedagogy and learning of Malaysian primary school children. The information provided to policy makers allows them to make a sound judgement and enables an informed decision making.

Keywords: attitudes towards virtual learning environment (VLE), parental perception, student's learning, teacher's pedagogy

Procedia PDF Downloads 196

Authors: Arjumand Warsy

Abstract:

The Holy Quran was revealed to Prophet Mohammad (May Peace and Blessings of Allah be upon Him) over fourteen hundred years ago, at a time when majority of the people in Arabia were illiterate and very few could read or write. Any knowledge about medicine, anatomy, biology, astronomy, physics, geology, geophysics or other sciences were almost non-existent. Many superstitious and groundless believes were prevalent and these believes were passed down through past generations. At that time, the Holy Quran was revealed and it presented several phenomenon that have been only currently unveiled, as scientists have worked endlessly to provide explanation for these physical and biological phenomenon applying scientific technologies. Many important discoveries were made during the 20th century and it is interesting to note that many of these discoveries were already present in the Holy Quran fourteen hundred years ago. The Scientific phenomenon, mentioned in the Holy Quran, cover many different fields in biological and physical sciences and have been the source of guidance for a number of scientists. A perfect description of the creation of the universe, the orbits in space, the development process, development of hearing process prior to sight, importance of the skin in sensing pain, uniqueness of fingerprints, role of males in selection of the sex of the baby, are just a few of the many facts present in the Quran that have astonished many scientists. The Quran in Chapter 20, verse 50 states: قَالَ رَبُّنَا الَّذِيۤ اَعْطٰى كُلَّ شَيْءٍ خَلْقَهٗ ثُمَّ هَدٰى ۰۰ (He said "Our Lord is He, Who has given a distinctive form to everything and then guided it aright”). Explaining this brief statement in the light of the modern day Molecular Genetics unveils the entire genetic basis of life and how guidance is stored in the genetic material (DNA) present in the nucleus. This thread like structure, made of only six molecules (sugar, phosphate, adenine, thymine, cytosine and guanine), is so brilliantly structured by the Creator that it holds all the information about each and every living thing, whether it is viruses, bacteria, fungi, plants, animals or humans or any other living being. This paper will present an update on some of the physical and biological phenomena’ presented in the Holy Quran, unveiled using advanced technologies during the last century and will discuss how the need to incorporate this information in the curricula.

Keywords: The Holy Quran, scientific facts, curriculum, Muslims

Procedia PDF Downloads 344

Authors: Sinchul Back, Sun Ho Kim, Jennifer LaPrade, Ilju Seong

Abstract:

Due to the advantage of using the Internet, cybercriminals can reach target(s) without border controls. Prior research on criminology and crime science has largely been void of empirical studies on journey-to-cybercrime and crime opportunity. Thus, the purpose of this study is to understand more about cyber offender spatial decision making associated with crime opportunity factors (i.e., co-offending, offender-stranger). Data utilized in this study were derived from 306 U.S. Federal court cases of cybercrime. The findings of this study indicated that there was a positive relationship between co-offending and journey-to-cybercrime, whereas there was no link between offender-stranger and journey-to-cybercrime. Also, the results showed that there was no relationship between cybercriminal sex, age, and journey-to-cybercrime. The policy implications and limitations of this study are discussed.

Keywords: co-offending, crime opportunity, journey-to-cybercrime, offender-stranger

Procedia PDF Downloads 165

Authors: Rene Davids

Abstract:

Urban undergrounds spaces such as parking garages or metro stations are perceived as interludes before reaching desired destinations, as commodities devoid of aesthetic value. Within the encoded space of the city, commercial underground spaces are the closest expression to pure to structures of consumption and commodity. Even in the house, the cellar is associated with castoffs and waste or, as scholar Mircea Eliade has pointed out at best, with a place to store abandoned household and childhood objects, which lie forgotten and on rediscovery evoke a nostalgic and uncanny sense of the past. Despite a growing body of evidence presented by an increasing number of buildings situated entirely below or semi underground that feature exemplary spatial and sensuous qualities, critics and scholars see them largely as efforts to produce efforts in producing low consumption non-renewable energy. Buildings that also free space above ground. This critical approach neglects to mention and highlight other project drivers such as the notion that the ground and sky can be considered a building’s fundamental context, that underground spaces are conducive to the exploration of pure space, namely an architecture that doesn’t have to deal with facades and or external volumes and that digging into geology can inspire the textural and spatial richness. This paper will argue that while the assessment about the reduced energy consumption of underground construction is important, it does not do justice to the qualities underground buildings can contribute to a city’s expanded urban and or landscape experiences.

Keywords: low non-renewable energy consumption, pure space, underground buildings, urban and landscape experience

Procedia PDF Downloads 169

Authors: Salam Khalifa, Naveed Ahmed

Abstract:

We present a new method to reconstruct a temporally coherent 3D animation from single or multi-view RGB-D video data using unbiased feature point sampling. Given RGB-D video data, in form of a 3D point cloud sequence, our method first extracts feature points using both color and depth information. In the subsequent steps, these feature points are used to match two 3D point clouds in consecutive frames independent of their resolution. Our new motion vectors based dynamic alignment method then fully reconstruct a spatio-temporally coherent 3D animation. We perform extensive quantitative validation using novel error functions to analyze the results. We show that despite the limiting factors of temporal and spatial noise associated to RGB-D data, it is possible to extract temporal coherence to faithfully reconstruct a temporally coherent 3D animation from RGB-D video data.

Keywords: 3D video, 3D animation, RGB-D video, temporally coherent 3D animation

Procedia PDF Downloads 357

Authors: Ahmed Sameer, Braj Bhushan

Abstract:

The objective of our study was to compare two techniques (no landmark vs imaginary landmark) of remembering route while traversing in an unfamiliar homogenous environment. We used two videos each having nine identical turns with no landmarks. In the first video participant was required to remember the sequence of turns. In the second video participant was required to imagine a landmark at each turn and associate the turn with it. In both the task the participant was asked to recall the sequence of turns as it appeared in the video. Results showed that performance in the first condition i.e. without use of landmarks was better than imaginary landmark condition. The difference, however, became significant when the participant were tested again about 30 minutes later though performance was still better in no-landmark condition. The finding is surprising given the past research in memory and is explained in terms of cognitive factors such as mental workload.

Keywords: wayfinding, landmarks, unfamiliar environment, cognitive psychology

Procedia PDF Downloads 457

Authors: Rungpansa Noichan, Bart Julian Dewancker

Abstract:

Thailand facing the transportation issue because of the rapid economic development. The big issue is the traffic jam, especially in Bangkok. However, recently years Bangkok has operated urban mass transit system for solved transportation problem. The Bangkok Mass Transit System (BTS) skytrain is being operated by the BTS Company Limited under the Bangkok Metropolitan Administration. The passenger satisfaction is a major cause for concern due to the commercial nature. The focus of this paper is to evaluate the passenger satisfaction at the mass transit node by questionnaires survey. The survey was to find out the passenger attitudes. The result shows several important factors that influence the passenger choice of using the BTS as a public transportation mode and the passenger’s opinion.

Keywords: urban transportation, user satisfaction, accessibility, Bangkok mass transit

Procedia PDF Downloads 272

Authors: Benjamin Beltzung, Marie Pelé, Julien P. Renoult, Cédric Sueur

Abstract:

To this day, it is not known if drawing is specifically human behavior or if this behavior finds its origins in ancestor species. An interesting window to enlighten this question is to analyze the drawing behavior in genetically close to human species, such as non-human primate species. A good candidate for this approach is the orangutan, who shares 97% of our genes and exhibits multiple human-like behaviors. Focusing on figurative aspects may not be suitable for orangutans’ drawings, which may appear as scribbles but may have meaning. A manual feature selection would lead to an anthropocentric bias, as the features selected by humans may not match with those relevant for orangutans. In the present study, we used deep learning to analyze the drawings of a female orangutan named Molly († in 2011), who has produced 1,299 drawings in her last five years as part of a behavioral enrichment program at the Tama Zoo in Japan. We investigate multiple ways to decipher Molly’s drawings. First, we demonstrate the existence of differences between seasons by training a deep learning model to classify Molly’s drawings according to the seasons. Then, to understand and interpret these seasonal differences, we analyze how the information spreads within the network, from shallow to deep layers, where early layers encode simple local features and deep layers encode more complex and global information. More precisely, we investigate the impact of feature complexity on classification accuracy through features extraction fed to a Support Vector Machine. Last, we leverage style transfer to dissociate features associated with drawing style from those describing the representational content and analyze the relative importance of these two types of features in explaining seasonal variation. Content features were relevant for the classification, showing the presence of meaning in these non-figurative drawings and the ability of deep learning to decipher these differences. The style of the drawings was also relevant, as style features encoded enough information to have a classification better than random. The accuracy of style features was higher for deeper layers, demonstrating and highlighting the variation of style between seasons in Molly’s drawings. Through this study, we demonstrate how deep learning can help at finding meanings in non-figurative drawings and interpret these differences.

Keywords: cognition, deep learning, drawing behavior, interpretability

Procedia PDF Downloads 142

Authors: Rehab Abdullah Shendi

Abstract:

The use of customised soft-core processors in which instructions can be integrated into a system in application hardware is increasing in the Field Programmable Gate Array (FPGA) field. Specifically, the partial run-time reconfiguration of FPGAs in specialised processors for a particular domain can be very beneficial. In this report, the design and implementation for the customisation of a soft-core MIPS processor using an FPGA and partial reconfiguration (PR) of FPGA technology will be addressed to achieve efficient resource use. This can be achieved using a PR design flow that helps the design fit into a smaller device. Moreover, the impact of static power consumption could be reduced due to runtime reconfiguration. This will be done by configurable custom instructions implemented in the hardware as an extension on the MIPS CPU. The aim of this project is to investigate the PR of FPGAs for run-time adaptations of the instruction set of a soft-core CPU, including the integration of custom instructions and the exploration of the potential to use the MultiBoot feature available in Xilinx FPGAs to carry out the PR process. The system will be evaluated and tested on a Nexus 3 development board featuring a Xilinx Spartran-6 FPGA. The system will be able to load reconfigurable custom instructions dynamically into user programs with the help of the trap handler when the custom instruction is called by the MIPS CPU. The results of this experiment demonstrate that custom instructions in hardware can speed up a certain function and many instructions can be saved when compared to a software implementation of the same function. Implementing custom instructions in hardware is perfectly possible and worth exploring.

Keywords: customisation, FPGA, MIPS, partial reconfiguration, PR

Procedia PDF Downloads 253

Authors: Mohamad Najari, Gilbert Grondin, Marwan El-Rich

Abstract:

Design trucks in standard codes are selected based on the amount of damage they cause on structures-specifically bridges- and roads to represent the real traffic loads. Some limited numbers of trucks are run on a bridge one at a time and the damage on the bridge is recorded for each truck. One design track is also run on the same bridge “n” times -“n” is the number of trucks used previously- to calculate the damage of the design truck on the same bridge. To make these damages equal a reduction factor is needed for that specific design truck in the codes. As the limited number of trucks cannot be the exact representative of real traffic through the life of the structure, these reduction factors are not accurately calculated and they should be modified accordingly. Started on July 2004, the vehicle load data were collected in six weigh in motion (WIM) sites owned by Alberta Transportation for eight consecutive years. This database includes more than 200 million trucks. Having these data gives the opportunity to compare the effect of any standard fatigue trucks weigh and the real traffic load on the fatigue life of the bridges which leads to a modification for the fatigue truck factor in the code. To calculate the damage for each truck, the truck is run on the bridge, moment history of the detail under study is recorded, stress range cycles are counted, and then damage is calculated using available S-N curves. A 2000 lines FORTRAN code has been developed to perform the analysis and calculate the damages of the trucks in the database for all eight fatigue categories according to Canadian Institute of Steel Construction (CSA S-16). Stress cycles are counted using rain flow counting method. The modification factors for design truck (CL-625) are calculated for two different bridge configurations and ten span lengths varying from 1 m to 200 m. The two considered bridge configurations are single-span bridge and four span bridge. This was found to be sufficient and representative for a simply supported span, positive moment in end spans of bridges with two or more spans, positive moment in interior spans of three or more spans, and the negative moment at an interior support of multi-span bridges. The moment history of the mid span is recorded for single-span bridge and, exterior positive moment, interior positive moment, and support negative moment are recorded for four span bridge. The influence lines are expressed by a polynomial expression obtained from a regression analysis of the influence lines obtained from SAP2000. It is found that for design truck (CL-625) fatigue truck factor is varying from 0.35 to 0.55 depending on span lengths and bridge configuration. The detail results will be presented in the upcoming papers. This code can be used for any design trucks available in standard codes.

Keywords: bridge, fatigue, fatigue design truck, rain flow analysis, FORTRAN

Procedia PDF Downloads 512

Authors: Carla Maria Furuno Rimkus

Abstract:

The technologies related to virtual reality and augmented reality in combination with mobile technologies, are being more consolidated and used each day. The increasing technological availability along with the decrease of their acquisition and maintenance costs, have favored the expansion of its use in the field of historic heritage. In this context it is focused, in this article, on the potential of mobile applications in the dissemination of the architectural heritage, using the technology of Augmented Reality. From this perspective approach, it is discussed about the process of producing an application for mobile devices on the Android platform, which combines the technologies of geometric modeling with augmented reality (AR) and access to interactive multimedia contents with cultural, social and historic information of the historic building that we take as the object of study: a block with a set of buildings built in the XVIII century, known as "Quarteirão dos Trapiches", which was modeled in 3D, coated with the original texture of its facades and displayed on AR. From this perspective approach, this paper discusses about methodological aspects of the development of this application regarding to the process and the project development tools, and presents our considerations on methodological aspects of developing an application for the Android system, focused on the dissemination of the architectural heritage, in order to encourage the tourist potential of the city in a sustainable way and to contribute to develop the digital documentation of the heritage of the city, meeting a demand of tourists visiting the city and the professionals who work in the preservation and restoration of it, consisting of architects, historians, archaeologists, museum specialists, among others.

Keywords: augmented reality, architectural heritage, geometric modeling, mobile applications

Procedia PDF Downloads 467

Authors: Kevin Wongleedee, Atcharapun Daiporn

Abstract:

This research paper was aimed to examine the level of satisfaction of the faculty and staff members who participated in the ASEAN camp. The population of this study included all the faculty and staff members who participated in the activities of the ASEAN camp during January 2014. Based on 106 faculty and staff members who answered the questionnaire, the data were complied by using SPSS. Mean and standard deviation were utilized in analyzing the data. The findings revealed that the average mean of satisfaction was 4.16, and standard deviation was 0.6634. Moreover, the mean average can be used to rank the level of satisfaction from each of the following factors: useful knowledge, technique of explaining knowledge, understanding materials, appropriateness of knowledge, document available, time of activities, service from staff, and public relation.

Keywords: ASEAN camp, customer, satisfaction, faculty and staff members

Procedia PDF Downloads 371

Authors: Pooja Booluck

Abstract:

This project seeks to translate a chapter in Le Silence des Chagos by Shenaz Patel a Mauritian author whose work has never been translated before. The chapter discusses the attempt of the protagonist to return to her home country Diego Garcia after her deportation. The English translation will offer an historical account to the target audience of the deportation of Chagossians to Mauritius during the 1970s. The target audience comprises of English-speaking translation scholars translation students and African literature scholars. In light of making the cultural elements of Mauritian culture accessible the translation will maintain the cultural items such as food and oral discourses in Creole so as to preserve the authenticity of the source culture. In order to better comprehend the cultural elements mentioned the target reader will be provided with detailed footnotes explaining the cultural and historical references. This translation will also address the importance of folkloric songs in Mauritius and its intergenerational function in Mauritian communities which will also remain in Creole. While such an approach will help to preserve the meaning of the source text the borrowing technique and the foreignizing method will be employed which will in turn help the reader in becoming more familiar with the Mauritian community. Translating a text from French to English while maintaining certain words or discourses in a minority language such as Creole bears certain challenges: How does the translator ensure the comprehensibility of the reader? Are there any translation losses? What are the choices of the translator?

Keywords: Chagos archipelagos in Exile, English translation, Le Silence des Chagos, Mauritian culture and history

Procedia PDF Downloads 301

Authors: William Middleton, Nodumo Zulu, Sue Harrison

Abstract:

Open raceway ponds are currently the most used system for the commercial cultivation of algal biomass, as it is a cost-effective means of production. However, raceway ponds suffer from lower algal productivity when compared to closed photobioreactors. This is due to poor gas exchange between the fluid and the atmosphere. Carbon dioxide (CO₂) mass transfer is a large concern in the production of algae in raceway pond systems. The utilization of atmospheric CO₂ does not support maximal growth; however, CO₂ supplementation in the form of flue gas or concentrated CO₂ is not cost-effective. The introduction of slopes into the raceway system presents a possible improvement to the mass transfer from the air, as seen in previous work conducted at CeBER. Slopes improve turbulence (decreasing the concentration gradient of dissolved CO₂) and can cause air entrainment (allowing for greater surface area and contact time between the air and water). This project tests the findings of previous studies conducted in an indoor lab-scale raceway on a larger scale under outdoor conditions. The addition of slopes resulted in slightly increased CO₂ mass transfer as well as algal growth rate and productivity. However, there were reductions in energy consumption and average fluid velocity in the system. These results indicate a potential to improve the economic feasibility of algal biomass production, but further economic assessment would need to be carried out.

Keywords: algae, raceway ponds, mass transfer, algal culture, biotechnology, reactor design

Procedia PDF Downloads 77

Authors: Majid Zargar, Frank Bullen, Ron Ayers

Abstract:

One of the important factors in the design of asphalt concrete mixes is the accurate measurement of air voids and their variable distribution. Both can have significant impact on long and short term fatigue and creep behaviour under traffic. While some simple methods exist for overall evaluation of air voids, measuring air void distribution in asphalt concrete is very complex, involving expensive techniques such as X-ray methodologies. The research reported in the paper investigated the use of non-destructive ultrasonic techniques as an alternative to estimate the amount of air voids and their distribution within asphalt samples. Seventy-four Standard AC–14 asphalt samples made with three types of bitumen; Multigrade, PMB and C320 were analysed using ultrasonic techniques. The results have illustrated that ultrasonic testing has the potential of being a rapid, accurate and cost-effective method of estimating air void distribution in asphalt.

Keywords: asphalt concrete, air voids, ultrasonic, mechanical behaviour

Procedia PDF Downloads 332

Authors: Gayle Nunley

Abstract:

Between the mid-nineteenth and early twentieth century, a number of Western European women broke with gender norms of their time and undertook to write and publish accounts of their own international journeys. In addition to contributing to their contemporaries’ progressive reimagining of the space and place of female experience within the public sphere, these often orientalism-tinged texts have come to provide key source material for the analysis of gendered voice in the narration of Empire, particularly with regard to works associated with Europe’s then-ascendant imperial powers, Britain and France. Incorporation of contemporaneous writings from the once-dominant Empires of Iberian Europe introduces an important additional lens onto this process. By bringing to bear geographic notions of placedness together with discourse analysis, the examination of works by Iberian Europe’s female travelers in conjunction with those of their more celebrated Northern European peers reveals a pervasive pattern of conjoined belonging and displacement traceable throughout the broader corpus, while also underscoring the insufficiency of binary paradigms of gendered voice. The re-situating of women travelers’ participation in the European imperial project to include voices from the Iberian south creates a more robust understanding of these writers’ complex, and often unexpectedly modern, engagement with notions of gender, mobility, ‘otherness’ and contact-zone encounter acted out both within and against the imperial paradigm.

Keywords: colonialism, orientalism, Spain, travel writing, women travelers

Procedia PDF Downloads 96

Authors: Murtala Marafa

Abstract:

This research is on socio-economic contributions of the Kanuri migrant community in Sokoto City during the 20th century. Kanuri migrants have been one of the major migrant groups who played and still playing positive role in the development of Sokoto city. The research will make an attempt to examine both the push and pulls factors responsible for Kanuri migration to Sokoto City. It is in the light of this that the research will examine and capture profiles of select prominent Kanuri migrants within the Sokoto city, in order to identify their major economic contributions to the development of Sokoto City. It is hoped that the study will show in the final analysis that the migration of Kanuri to Sokoto city have impacted positively to the socio-economic development of Sokoto city.

Keywords: development, economy, Kanuri, migration

Procedia PDF Downloads 254

Authors: Mary Holstein

Abstract:

Objective: The aim of this study was to evaluate nurse leader confidence in emergency management and disaster preparedness in the state of Texas. My project was a replication study of a survey conducted in 2022 by Reedy et al, for members of the Northwest Organization for Nurse Leaders (NONL). Background: In 2022, the American Association of Colleges of Nursing (AACN) approved new essentials for academic nursing education programs to demonstrate competencies in disaster management, yet no integration of such information into nursing curriculum had been reported in the literature. Research replicated by members of the Texas Organization for Nursing Leadership suggested significant gaps in nurse leader confidence across roles and in structured education that prepares nurse leaders across the spectrum of experience to lead in a crisis. Methods: An exploratory, cross-sectional survey used a sample of 86 RNs who were members of TONL. Results: Results replicated comparable results with significant variance in nurse leader confidence across roles, experience, and previous disaster-related education. Positive associations regarding nurse leaders' confidence in managing disasters were obvious with more advanced positions, further education, and mandatory training. Conclusions: Nursing leaders in Texas lack mandatory and structured education to prepare for emergency and disaster management. The call for mandatory emergency management training and disaster preparedness for nurse leaders remains unmet.

Keywords: confidence, disaster, education, emergency

Procedia PDF Downloads 50

Authors: M. Şimşek

Abstract:

Rapidly changing factors that affect daily life also affect operational environment and the way military leaders fulfill their missions. With the help of technological developments, traditional linearity of conflict and war has started to fade away. Furthermore, mission domain has broadened to include traditional threats, hybrid threats and new challenges of cyber and space. Considering the future operational environment, future military leaders need to adapt themselves to the new challenges of the future battlefield. But how to decide what kind of features of leadership are required to operate and accomplish mission in the new complex battlefield? In this article, the main aim is to provide answers to this question. To be able to find right answers, first leadership and leadership components are defined, and then characteristics of future operational environment are analyzed. Finally, leadership features that are required to be successful in redefined battlefield are explained.

Keywords: future operational environment, leadership, leadership components

Procedia PDF Downloads 422

Authors: S. K. Gupta, Richa Bansal

Abstract:

In a deregulated power system structure, power producers, and customers share a common transmission network for wheeling power from the point of generation to the point of consumption. All parties in this open access environment may try to purchase the energy from the cheaper source for greater profit margins, which may lead to overloading and congestion of certain corridors of the transmission network. This may result in violation of line flow, voltage and stability limits and thereby undermine the system security. Utilities therefore need to determine adequately their Available Transfer Capability (ATC) to ensure that system reliability is maintained while serving a wide range of bilateral and multilateral transactions. This paper presents power transfer distribution factor based on AC load flow for the determination and enhancement of ATC. The study has been carried out for IEEE 24 bus Reliability Test System.

Keywords: available transfer capability, FACTS devices, power transfer distribution factors, electric

Procedia PDF Downloads 487

Authors: Oshada Gamage, Chamal Wimalasooriya, Chrismal Boteju, W. K. Wimalsiri

Abstract:

This paper presents a study on the feasibility of introducing a solar powered propelling mechanism to multi-day fishing boats as an alternative energy source. Since solar energy is readily available on the sea throughout the year, this free energy could be utilized to power multi-day fishing vessels. Multi-day boats have a large deck area where solar panels can be mounted above without much effort. This project involves studying the amount of power that can be generated using onboard solar panels and implementing an independent propelling system to run the boat. A chain drive system was designed to propel the boat, when the batteries are fully charged, from an electric motor using the same propeller. A 60 feet multi-day fishing boat built by a local boat manufacturer was chosen for the study. The service speed of the boat was around 6 knots with the electric motor, and the duration of cruising is 1 hour per day with around 11 hours of charging. 350-watt Mono-crystalline PV module, 75 kW HVH type motor, and 10 kWh lithium-ion battery packs were chosen for the study. From the calculations, it was obtained that the boat has 30 PV modules (10.5 kW), 5 batteries (47 kWh), The boat dimensions are 20 meter length of water line, 5.51 meter of beam, 1.8 meter of draught, and 77 ton of total displacement with the PV system net present value of USD 12445 for 20 years of operation and a payback period of around 8.2 years.

Keywords: multiday fishing boats, photovoltaic cells, solar energy, solar powered boat

Procedia PDF Downloads 136