Search results for: Newcomb’s problem

Authors: Ali H. Daraji, Jack M. Hale, Ye Jianqiao

Abstract:

With the extensive use of high specific strength structures to optimise the loading capacity and material cost in aerospace and most engineering applications, much effort has been expended to develop intelligent structures for active vibration reduction and structural health monitoring. These structures are highly flexible, inherently low internal damping and associated with large vibration and long decay time. The modification of such structures by adding lightweight piezoelectric sensors and actuators at efficient locations integrated with an optimal control scheme is considered an effective solution for structural vibration monitoring and controlling. The size and location of sensor and actuator are important research topics to investigate their effects on the level of vibration detection and reduction and the amount of energy provided by a controller. Several methodologies have been presented to determine the optimal location of a limited number of sensors and actuators for small-scale structures. However, these studies have tackled this problem directly, measuring the fitness function based on eigenvalues and eigenvectors achieved with numerous combinations of sensor/actuator pair locations and converging on an optimal set using heuristic optimisation techniques such as the genetic algorithms. This is computationally expensive for small- and large-scale structures subject to optimise a number of s/a pairs to suppress multiple vibration modes. This paper proposes an efficient method to determine optimal locations for a limited number of sensor/actuator pairs for active vibration reduction of a flexible structure based on finite element method and Hamilton’s principle. The current work takes the simplified approach of modelling a structure with sensors at all locations, subjecting it to an external force to excite the various modes of interest and noting the locations of sensors giving the largest average percentage sensors effectiveness measured by dividing all sensor output voltage over the maximum for each mode. The methodology was implemented for a cantilever plate under external force excitation to find the optimal distribution of six sensor/actuator pairs to suppress the first six modes of vibration. It is shown that the results of the optimal sensor locations give good agreement with published optimal locations, but with very much reduced computational effort and higher effectiveness. Furthermore, it is shown that collocated sensor/actuator pairs placed in these locations give very effective active vibration reduction using optimal linear quadratic control scheme.

Keywords: optimisation, plate, sensor effectiveness, vibration control

Procedia PDF Downloads 232

Authors: S. Masud, J. Merson, D. F. Robinson

Abstract:

The management of environmental resources requires engagement of a range of stakeholders including public/private agencies and different community groups to implement sustainable conservation practices. The challenge which is often ignored is the analysis of agencies involved and their power relations. One of the barriers identified is the difference in risk perceptions among the agencies involved that leads to disjointed efforts of assessing and managing risks. Wood et al 2012, explains that it is important to have an integrated approach to risk management where decision makers address stakeholder perspectives. This is critical for an effective risk management policy. This abstract is part of a PhD research that looks into barriers to flood management under a changing climate and intends to identify bottlenecks that create maladaptation. Experiences are drawn from international practices in the UK and examined in the context of Australia through exploring the flood governance in a highly flood-prone region in Australia: the Hawkesbury Ne-pean catchment as a case study. In this research study several aspects of governance and management are explored: (i) the complexities created by the way different agencies are involved in assessing flood risks (ii) different perceptions on acceptable flood risk level; (iii) perceptions on community engagement in defining acceptable flood risk level; (iv) Views on a holistic flood risk management approach; and, (v) challenges of centralised information system. The study concludes that the complexity of managing a large catchment is exacerbated by the difference in the way professionals perceive the problem. This has led to: (a) different standards for acceptable risks; (b) inconsistent attempt to set-up a regional scale flood management plan beyond the jurisdictional boundaries: (c) absence of a regional scale agency with license to share and update information (d) Lack of forums for dialogue with insurance companies to ensure an integrated approach to flood management. The research takes the Hawkesbury-Nepean catchment as case example and draws from literary evidence from around the world. In addition, conclusions were extrapolated from eighteen semi-structured interviews from agencies involved in flood risk management in the Hawkesbury-Nepean catchment of NSW, Australia. The outcome of this research is to provide a better understanding of complexity in assessing risks against a rapidly changing climate and contribute towards developing effective risk communication strategies thus enabling better management of floods and achieving increased level of support from insurance companies, real-estate agencies, state and regional risk managers and the affected communities.

Keywords: adaptive governance, flood management, flood risk communication, stakeholder risk perceptions

Procedia PDF Downloads 286

Authors: Mustafa M. Donma, Orkide Donma

Abstract:

Metabolic syndrome (MetS) is a severe health problem which is common among obese individuals. The components of MetS are rather stable in adults compared to the components discussed for children. Due to the ambiguity in this group of the population, how to diagnose MetS in morbid obese (MO) children still constitutes a matter of discussion. For this purpose, a formula, which facilitates the diagnosis of MetS in MO children, was investigated. The aim of this study was to develop a formula which was capable of discriminating MO children with and without MetS findings. Study population comprised MO children. Age and sex-dependent body mass index (BMI) percentiles of the children were above 99. Metabolic syndrome components were also determined. Elevated systolic and diastolic blood pressures (SBP and DBP), elevated fasting blood glucose (FBG), elevated triglycerides (TRG), and/or depressed high density lipoprotein cholesterol (HDL-C) in addition to central obesity were listed as MetS components for each child. Presence of at least two of these components confirmed that the case was MetS. Two groups were constituted. In the first group, there were forty-two MO children without MetS components. Second group was composed of forty-four MO children with at least two MetS components. Anthropometric measurements, including weight, height, waist, and hip circumferences, were performed following physical examination. Body mass index and homeostatic model assessment of insulin resistance values were calculated. Informed consent forms were obtained from the parents of the children. Institutional Non-Interventional Ethics Committee approved the study design. Blood pressure values were recorded. Routine biochemical analysis, including FBG, insulin (INS), TRG, HDL-C were performed. The performance and the clinical utility of the Diagnostic Obesity Notation Model Assessment Metabolic Syndrome Index (DONMA MetS index) [(INS/FBG)/(HDL-C/TRG)*100] was tested. Appropriate statistical tests were applied to the study data. p value smaller than 0.05 was defined as significant. Metabolic syndrome index values were 41.6±5.1 in MO group and 104.4±12.8 in MetS group. Corresponding values for HDL-C values were 54.5±13.2 mg/dl and 44.2±11.5 mg/dl. There were statistically significant differences between the groups (p<0.001). Upon evaluation of the correlations between MetS index and HDL-C values, a much stronger negative correlation was found in MetS group (r=-0.515; p=0.001) in comparison with the correlation detected in MO group (r=-0.371; p=0.016). From these findings, it was concluded that the statistical significance degree of the difference between MO and MetS groups was highly acceptable for this recently introduced MetS index as expected. This was due to the involvement of all of the biochemically defined MetS components into the index. This is particularly important because each of these four parameters used in the formula is cardiac risk factor. Aside from discriminating MO children with and without MetS findings, MetS index introduced in this study is important from the cardiovascular risk point of view in MetS group of children.

Keywords: children, fasting blood glucose, high density lipoprotein cholesterol, index, insulin, metabolic syndrome, morbid obesity, triglycerides.

Procedia PDF Downloads 92

Authors: Tomas Makaras, Gintaras Svecevičius

Abstract:

Landfill waste is a common problem as it has an economic and environmental impact even if it is closed. Landfill waste contains a high density of various persistent compounds such as heavy metals, organic and inorganic materials. As persistent compounds are slowly-degradable or even non-degradable in the environment, they often produce sublethal or even lethal effects on aquatic organisms. The aims of the present study were to estimate sublethal effects of the Kairiai landfill (WGS: 55°55‘46.74“, 23°23‘28.4“) leachate on the locomotor activity of rainbow trout Oncorhynchus mykiss juveniles using the original system package developed in our laboratory for automated monitoring, recording and analysis of aquatic organisms’ activity, and to determine patterns of fish behavioral response to sublethal effects of leachate. Four different concentrations of leachate were chosen: 0.125; 0.25; 0.5 and 1.0 mL/L (0.0025; 0.005; 0.01 and 0.002 as part of 96-hour LC50, respectively). Locomotor activity was measured after 5, 10 and 30 minutes of exposure during 1-minute test-periods of each fish (7 fish per treatment). The threshold-effect-concentration amounted to 0.18 mL/L (0.0036 parts of 96-hour LC50). This concentration was found to be even 2.8-fold lower than the concentration generally assumed to be “safe” for fish. At higher concentrations, the landfill leachate solution elicited behavioral response of test fish to sublethal levels of pollutants. The ability of the rainbow trout to detect and avoid contaminants occurred after 5 minutes of exposure. The intensity of locomotor activity reached a peak within 10 minutes, evidently decreasing after 30 minutes. This could be explained by the physiological and biochemical adaptation of fish to altered environmental conditions. It has been established that the locomotor activity of juvenile trout depends on leachate concentration and exposure duration. Modeling of these parameters showed that the activity of juveniles increased at higher leachate concentrations, but slightly decreased with the increasing exposure duration. Experiment results confirm that the behavior of rainbow trout juveniles is a sensitive and rapid biomarker that can be used in combination with the system for fish behavior monitoring, registration and analysis to determine sublethal concentrations of pollutants in ambient water. Further research should be focused on software improvement aimed to include more parameters of aquatic organisms’ behavior and to investigate the most rapid and appropriate behavioral responses in different species. In practice, this study could be the basis for the development and creation of biological early-warning systems (BEWS).

Keywords: fish behavior biomarker, landfill leachate, locomotor activity, rainbow trout juveniles, sublethal effects

Procedia PDF Downloads 271

Authors: Jung-Hong Hong, Jing-Cen Yang, Cai-Yu Ou

Abstract:

The analysis of geographic inequality heavily relies on the use of location-enabled statistical data and quantitative measures to present the spatial patterns of the selected phenomena and analyze their differences. To protect the privacy of individual instance and link to administrative units, point-based datasets are spatially aggregated to area-based statistical datasets, where only the overall status for the selected levels of spatial units is used for decision making. The partition of the spatial units thus has dominant influence on the outcomes of the analyzed results, well known as the Modifiable Areal Unit Problem (MAUP). A new spatial reference framework, the Taiwan Geographical Statistical Classification (TGSC), was recently introduced in Taiwan based on the spatial partition principles of homogeneous consideration of the number of population and households. Comparing to the outcomes of the traditional township units, TGSC provides additional levels of spatial units with finer granularity for presenting spatial phenomena and enables domain experts to select appropriate dissemination level for publishing statistical data. This paper compares the results of respectively using TGSC and township unit on the mortality data and examines the spatial characteristics of their outcomes. For the mortality data between the period of January 1^st, 2008 and December 31^st, 2010 of the Taitung County, the all-cause age-standardized death rate (ASDR) ranges from 571 to 1757 per 100,000 persons, whereas the 2^nd dissemination area (TGSC) shows greater variation, ranged from 0 to 2222 per 100,000. The finer granularity of spatial units of TGSC clearly provides better outcomes for identifying and evaluating the geographic inequality and can be further analyzed with the statistical measures from other perspectives (e.g., population, area, environment.). The management and analysis of the statistical data referring to the TGSC in this research is strongly supported by the use of Geographic Information System (GIS) technology. An integrated workflow that consists of the tasks of the processing of death certificates, the geocoding of street address, the quality assurance of geocoded results, the automatic calculation of statistic measures, the standardized encoding of measures and the geo-visualization of statistical outcomes is developed. This paper also introduces a set of auxiliary measures from a geographic distribution perspective to further examine the hidden spatial characteristics of mortality data and justify the analyzed results. With the common statistical area framework like TGSC, the preliminary results demonstrate promising potential for developing a web-based statistical service that can effectively access domain statistical data and present the analyzed outcomes in meaningful ways to avoid wrong decision making.

Keywords: mortality map, spatial patterns, statistical area, variation

Procedia PDF Downloads 258

Authors: Efrain Rodriguez, Cristhian Riano, Alberto Alvares

Abstract:

In recent years, robots manipulators with parallel architectures are used in additive manufacturing processes – 3D printing. These robots have advantages such as speed and lightness that make them suitable to help with the efficiency and productivity of these processes. Consequently, the interest for the development of parallel robots for additive manufacturing applications has increased. This article deals with the conceptual design and dimensional synthesis of the linear delta robot for additive manufacturing. Firstly, a methodology based on structured processes for the development of products through the phases of informational design, conceptual design and detailed design is adopted: a) In the informational design phase the Mudge diagram and the QFD matrix are used to aid a set of technical requirements, to define the form, functions and features of the robot. b) In the conceptual design phase, the functional modeling of the system through of an IDEF0 diagram is performed, and the solution principles for the requirements are formulated using a morphological matrix. This phase includes the description of the mechanical, electro-electronic and computational subsystems that constitute the general architecture of the robot. c) In the detailed design phase, a digital model of the robot is drawn on CAD software. A list of commercial and manufactured parts is detailed. Tolerances and adjustments are defined for some parts of the robot structure. The necessary manufacturing processes and tools are also listed, including: milling, turning and 3D printing. Secondly, a dimensional synthesis method applied on design of the linear delta robot is presented. One of the most important key factors in the design of a parallel robot is the useful workspace, which strongly depends on the joint space, the dimensions of the mechanism bodies and the possible interferences between these bodies. The objective function is based on the verification of the kinematic model for a prescribed cylindrical workspace, considering geometric constraints that possibly lead to singularities of the mechanism. The aim is to determine the minimum dimensional parameters of the mechanism bodies for the proposed workspace. A method based on genetic algorithms was used to solve this problem. The method uses a cloud of points with the cylindrical shape of the workspace and checks the kinematic model for each of the points within the cloud. The evolution of the population (point cloud) provides the optimal parameters for the design of the delta robot. The development process of the linear delta robot with optimal dimensions for additive manufacture is presented. The dimensional synthesis enabled to design the mechanism of the delta robot in function of the prescribed workspace. Finally, the implementation of the robotic platform developed based on a linear delta robot in an additive manufacturing application using the Fused Deposition Modeling (FDM) technique is presented.

Keywords: additive manufacturing, delta parallel robot, dimensional synthesis, genetic algorithms

Procedia PDF Downloads 190

Authors: A. K. M. Zakir Hossain, Faruk-Ul Islam, Muhammad Alamgir Chowdhury, Kazi Morshed Alam, Md. Rashidul Islam, Muhammad Humayun Kabir, Noshin Ara Tunazzina, Taufiqur Rahman, Md. Ashik Mia, Ashaduzzaman Sagar

Abstract:

The jute retting process is one of the key factors for the excellent jute fibre production as well as maintaining water quality. The traditional method of jute retting is time-consuming and hampers the fish cultivation by polluting the water body. Therefore, a low cost, time-saving, environment-friendly, and improved technique is essential for jute retting to overcome this problem. Thus the study was focused to compare the extent of water pollution and fibre quality of two retting systems, i.e., traditional retting practices over-improved retting method (macha retting) by assessing different physico-chemical and microbiological properties of water and fibre quality parameters. Water samples were collected from the top and bottom of the retting place at the early, mid, and final stages of retting from four districts of Bangladesh viz., Gaibandha, Kurigram, Lalmonirhat, and Rangpur. Different physico-chemical parameters of water samples viz., pH, dissolved oxygen (DO), conductivity (CD), total dissolved solids (TDS), hardness, calcium, magnesium, carbonate, bicarbonate, chloride, phosphorus and sulphur content were measured. Irrespective of locations, the DO of the final stage retting water samples was very low as compared to the mid and early stage, and the DO of traditional jute retting method was significantly lower than the improved macha method. The pH of the water samples was slightly more acidic in the traditional retting method than that of the improved macha method. Other physico-chemical parameters of the water sample were found higher in the traditional method over-improved macha retting in all the stages of retting. Bacterial species were isolated from the collected water samples following the dilution plate technique. Microbiological results revealed that water samples of improved macha method contained more bacterial species that are supposed to involve in jute retting as compared to water samples of the traditional retting method. The bacterial species were then identified by the sequencing of 16SrDNA. Most of the bacterial species identified belong to the genera Pseudomonas, Bacillus, Pectobacterium, and Stenotrophomonas. In addition, the tensile strength of the jute fibre was tested, and the results revealed that the improved macha method showed higher mechanical strength than the traditional method in most of the locations. The overall results indicate that the water and fibre quality were found better in the improved macha retting method than the traditional method. Therefore, a time-saving and cost-friendly improved macha retting method can be widely adopted for the jute retting process to get the quality jute fiber and to keep the environment clean and safe.

Keywords: jute retting methods, physico-chemical parameters, retting microbes, tensile strength, water quality

Procedia PDF Downloads 157

Authors: Johan Buermans, Kristel Crombé, Niek Desmet, Laura Dittrich, Andrei Goriaev, Yurii Kovtun, Daniel López-Rodriguez, Sören Möller, Per Petersson, Maja Verstraeten

Abstract:

The International Thermonuclear Experimental Reactor (ITER) will rely on three sources of external heating to produce and sustain a plasma; Neutral Beam Injection (NBI), Ion Cyclotron Resonance Heating (ICRH), and Electron Cyclotron Resonance Heating (ECRH). ECRH is a way to heat the electrons in a plasma by resonant absorption of electromagnetic waves. The energy of the electrons is transferred indirectly to the ions by collisions. The electron cyclotron heating system can be directed to deposit heat in particular regions in the plasma (https://www.iter.org/mach/Heating). Electron Cyclotron Resonance Heating (ECRH) at the fundamental resonance in X-mode is limited by a low cut-off density. Electromagnetic waves cannot propagate in the region between this cut-off and the Upper Hybrid Resonance (UHR) and cannot reach the Electron Cyclotron Resonance (ECR) position. Higher harmonic heating is hence preferred in heating scenarios nowadays to overcome this problem. Additional power deposition mechanisms can occur above this threshold to increase the plasma density. This includes collisional losses in the evanescent region, resonant power coupling at the UHR, tunneling of the X-wave with resonant coupling at the ECR, and conversion to the Electron Bernstein Wave (EBW) with resonant coupling at the ECR. A more profound knowledge of these deposition mechanisms can help determine the optimal plasma production scenarios. Several ECRH experiments are performed on the TOroidally MAgnetized System (TOMAS) to identify the conditions for Electron Bernstein Wave (EBW) heating. Density and temperature profiles are measured with movable Triple Langmuir Probes in the horizontal and vertical directions. Measurements of the forwarded and reflected power allow evaluation of the coupling efficiency. Optical emission spectroscopy and camera images also contribute to plasma characterization. The influence of the injected power, magnetic field, gas pressure, and wave polarization on the different deposition mechanisms is studied, and the contribution of the Electron Bernstein Wave is evaluated. The TOMATOR 1D hydrogen-helium plasma simulator numerically describes the evolution of current less magnetized Radio Frequency plasmas in a tokamak based on Braginskii’s legal continuity and heat balance equations. This code was initially benchmarked with experimental data from TCV to determine the transport coefficients. The code is used to model the plasma parameters and the power deposition profiles. The modeling is compared with the data from the experiments.

Keywords: electron Bernstein wave, Langmuir probe, plasma characterization, TOMAS

Procedia PDF Downloads 96

Authors: P. H. G. J. Pushpakumara, Andrew Dawson

Abstract:

Introduction: Deliberate self harm (DSH) is a major public health problem globally. Suicide rates of Sri Lanka are being among the highest national rates in the world, since 1950. Previous DSH is the most important independent predictor of repetition. The estimated 1 year non-fatal repeat self-harm rate was 16.3%. Asian countries had considerably lower rate, 10.0%. Objectives: To calculate incidence of deliberate self-poisoning (DSP) and suicides, repetition rate of DSP in Kurunegala District (KD). To determine the pattern of repeated DSP in KD. Methods: Study had two components. In the first component, demographic and event related details of, DSP admission in 46 hospitals and suicides in 28 police stations of KD were collected for 3 years from January 2011. Demographic details of cohort of DSP patients admitted to above hospitals in 2011 were linked with hospital admissions and police records of next two years period from the index admission. Records were screened for links with high sensitivity using the computer then did manual matching which would have been much more specific. In the second component, randomly selected DSP patients (n=438), who admitted to main referral centre which receives 60% of DSP cases of the district, were interviewed to assess life-time repetition. Results: There were 16,993 DSP admissions and 1078 suicides for the three year period. Suicide incidences in KD were, 21.6, 20.7 and 24.3 per 100,000 population in 2011, 2012 and 2013. Average male to female ratio for suicide incidences was 5.5. DSP incidences were 205.4, 248.3 and 202.5 per 100,000 population. Male incidences were slightly greater than the female incidences, male: female ratio was 1.1:1. Highest age standardized male and female incidence was reported in 20-24 years age group, 769.6/100,000, and 15-19 years age group 1304.0/100,000. Male to female ratio of the incidence increased with the age. There were 318 (179 male and 139 female) patients attempted DSH within two years. Female repetitive patients were ounger compared to the males, p < 0.0001, median age: males 28 and females 19 years. 290 (91.2%) had only one repetitive attempt, 24 (7.5%) had two, 3 (0.9%) had three and one (0.3%) had four in that period. One year repetition rate was 5.6 and two year repetition rate was 7.9%. Average intervals between indexed events and first repetitive DSP events were 246.8 (SD:223.4) and 238.5 (SD:207.0) days among males and females. One fifth of first repetitive events occurred within first two weeks in both males and females. Around 50% of males and females had the second event within 28 weeks. Within the first year of the indexed event, around 70% had the second event. First repetitive event was fatal for 28 (8.8%) individuals. Ages of those who died, mean 49.7 years (SD:15.3), were significantly higher compared to those who had non-fatal outcome, p<0.0001. 9.5% had life time history of DSH attempts. Conclusions: Both, DSP and suicide incidences were very high in KD. However, repetition rates were lesser compared regional values. Prevention of repetition alone may not produce significant impact on prevention of DSH.

Keywords: deliberate self-harm, incidence, repetition, Sri Lanka, suicide

Procedia PDF Downloads 218

Authors: Kiran Kumar Gellaboina, Padmaja Kaja

Abstract:

Agricultural Education and Research in India needs a transformation to serve the needs of the farmers and that of the nation. The fact that Agriculture and allied activities act as main source of livelihood for more than 70% population of rural India reinforces its importance in administrative and policy arena. As per Census 2011 of India it provides employment to approximately 56.6 % of labour. India has achieved significant growth in agriculture, milk, fish, oilseeds and fruits and vegetables owing to green, white, blue and yellow revolutions which have brought prosperity to farmers. Many factors are responsible for these achievement viz conducive government policies, receptivity of the farmers and also establishment of higher agricultural education institutions. The new breed of skilled human resources were instrumental in generating new technologies, and in its assessment, refinement and finally its dissemination to the farming community through extension methods. In order to sustain, diversify and realize the potential of agriculture sectors, it is necessary to develop skilled human resources. Agricultural human resource development is a continuous process undertaken by agricultural universities. The Department of Agricultural Research and Education (DARE) coordinates and promotes agricultural research & education in India. In India, agricultural universities were established on ‘land grant’ pattern of USA which helped incorporation of a number of diverse subjects in the courses as also provision of hands-on practical exposure to the student. The State Agricultural Universities (SAUs) established through the legislative acts of the respective states and with major financial support from them leading to administrative and policy controls. It has been observed that pace and quality of technology generation and human resource development in many of the SAUs has gone down. The reason for this slackening are inadequate state funding, reduced faculty strength, inadequate faculty development programmes, lack of modern infrastructure for education and research etc. Establishment of new state agricultural universities and new faculties/colleges without providing necessary financial and faculty support has aggrieved the problem. The present work highlights some of the key issues affecting agricultural education and research in India and the impact it would have on farm productivity and sustainability. Secondary data pertaining to budgetary spend on agricultural education and research will be analyzed. This paper will study the trends in public spending on agricultural education and research and the per capita income of farmers in India. This paper tries to suggest that agricultural education and research has a key role in equipping the human resources for enhanced agricultural productivity and sustainable use of natural resources. Further, a total re-orientation of agricultural education with emphasis on other agricultural related social sciences is needed for effective agricultural policy research.

Keywords: agriculture, challenges, education, research

Procedia PDF Downloads 232

Authors: Xuan (Iris) Li, Jenny Zhengye Hou, Greg Hearn

Abstract:

Food waste is a global issue, with an estimated 30% to 50% of food created never being consumed. Therefore, it is vital to reduce food waste and convert wasted food into recyclable outputs. TikTok provides a simple way of creating and duetting videos in just a few steps by using templates with the same sound/vision/caption effects to produce personalized content – this is called a duet, which is revealing to study the impact of TikTok on wasting more food or saving food. The research focuses on examining food-related content on TikTok, with particular attention paid to two distinct themes, food waste pranks and food-saving practices, to understand the potential impacts of these themes on adolescents and their attitudes toward sustainable food consumption practices. Specifically, the analysis explores how TikTok content related to food waste and/or food saving may contribute to the normalization and promotion of either positive or negative food behaviours among young viewers. The research employed content analysis and semi-structured interviews to understand what factors contribute to the difference in popularity between food pranks and food-saving videos and insights from the former can be applied to the latter to increase their communication effectiveness. The first category of food content on TikTok under examination pertains to food waste, including videos featuring pranks and mukbang. These forms of content have the potential to normalize or even encourage food waste behaviours among adolescents, exacerbating the already significant food waste problem. The second category of TikTok food content under examination relates to food saving, for example, videos teaching viewers how to maximize the use of food to reduce waste. This type of content can potentially empower adolescents to act against food waste and foster positive and sustainable food practices in their communities. The initial findings of the study suggest that TikTok content related to pranks appears to be more popular among viewers than content focused on teaching people how to save food. Additionally, these types of videos are gaining fans at a faster rate than content promoting more sustainable food practices. However, we argue there is a great potential for social media platforms like TikTok to play an educative role in promoting positive behaviour change among young people by sharing engaging content suitable to target audiences. This research serves as the first to investigate the potential utility of TikTok in food waste reduction and underscores the important role social media platforms can play in promoting sustainable food practices. The findings will help governments, organizations, and communities promote tailored and effective interventions to reduce food waste and help achieve the United Nations’ sustainable development goal of halving food waste by 2030.

Keywords: food waste reduction, behaviour, social media, TikTok, adolescents

Procedia PDF Downloads 78

Authors: Dohwan Kim, Dongchoon Ryou, Pyungjong Yoo

Abstract:

In public water facilities, drinking water distribution systems have played an important role along with water purification systems. The water distribution network is one of the most expensive components of water supply infrastructure systems. To improve the reliability for the drinking rate of tap water, advanced water treatment processes such as granular activated carbon and membrane filtration were used by water service providers in Korea. But, distrust of the people for tap water are still. Therefore, accurate diagnosis and condition assessment for water pipelines are required to supply the clean water. The internal corrosion of water pipe has increased as time passed. Also, the cross-sectional areas in pipe are reduced by the rust, deposits and tubercles. It is the water supply ability decreases as the increase of hydraulic pump capacity is required to supply an amount of water, such as the initial condition. If not, the poor area of water supply will be occurred by the decrease of water pressure. In order to solve these problems, water managers and engineers should be always checked for the current status of the water pipe, such as water leakage and damage of pipe. If problems occur, it should be able to respond rapidly and make an accurate estimate. In Korea, replacement and rehabilitation of aging drinking water pipes are carried out based on the circumstances of simply buried years. So, water distribution system management may not consider the entire water pipeline network. The long-term design and upgrading of a water distribution network should address economic, social, environmental, health, hydraulic, and other technical issues. This is a multi-objective problem with a high level of complexity. In this study, the thickness of the old water pipes, corrosion levels of the inner and outer surface for water pipes, basic data research (i.e. pipe types, buried years, accident record, embedded environment, etc.), specific resistance of soil, ultimate tensile strength and elongation of metal pipes, samples characteristics, and chemical composition analysis were performed about aging drinking water pipes. Samples of water pipes used in this study were cement mortar lining ductile cast iron pipe (CML-DCIP, diameter 100mm) and epoxy lining steel pipe (diameter 65 and 50mm). Buried years of CML-DCIP and epoxy lining steel pipe were respectively 32 and 23 years. The area of embedded environment was marine reclamation zone since 1940’s. The result of this study was that CML-DCIP needed replacement and epoxy lining steel pipe was still useful.

Keywords: drinking water distribution system, water supply, replacement, rehabilitation, water pipe

Procedia PDF Downloads 258

Authors: D. Serero, L. Couton, J. D. Parisse, R. Leroy

Abstract:

In urban planning, an increasing number of cities require wind analysis to verify comfort of public spaces and around buildings. These studies are made using computer fluid dynamic simulation (CFD). However, this technique is often based on wind information taken from meteorological stations located at several kilometers of the spot of analysis. The approximated input data on project surroundings produces unprecise results for this type of analysis. They can only be used to get general behavior of wind in a zone but not to evaluate precise wind speed. This paper presents another approach to this problem, based on collecting wind data and generating an urban wind cartography using connected ultrasound anemometers. They are wireless devices that send immediate data on wind to a remote server. Assembled in array, these devices generate geo-localized data on wind such as speed, temperature, pressure and allow us to compare wind behavior on a specific site or building. These Netatmo-type anemometers communicate by wifi with central equipment, which shares data acquired by a wide variety of devices such as wind speed, indoor and outdoor temperature, rainfall, and sunshine. Beside its precision, this method extracts geo-localized data on any type of site that can be feedback looped in the architectural design of a building or a public place. Furthermore, this method allows a precise calibration of a virtual wind tunnel using numerical aeraulic simulations (like STAR CCM + software) and then to develop the complete volumetric model of wind behavior over a roof area or an entire city block. The paper showcases connected ultrasonic anemometers, which were implanted for an 18 months survey on four study sites in the Grand Paris region. This case study focuses on Paris as an urban environment with multiple historical layers whose diversity of typology and buildings allows considering different ways of capturing wind energy. The objective of this approach is to categorize the different types of wind in urban areas. This, particularly the identification of the minimum and maximum wind spectrum, helps define the choice and performance of wind energy capturing devices that could be implanted there. The localization on the roof of a building, the type of wind, the altimetry of the device in relation to the levels of the roofs, the potential nuisances generated. The method allows identifying the characteristics of wind turbines in order to maximize their performance in an urban site with turbulent wind.

Keywords: computer fluid dynamic simulation in urban environment, wind energy harvesting devices, net-zero energy building, urban wind behavior simulation, advanced building skin design methodology

Procedia PDF Downloads 101

Authors: Wageeh A. Nafei

Abstract:

This paper explores the role of Paradoxical Leadership (PL) in enhancing Organizational Success (OS) at private hospitals in Egypt. Based on the collected data from employees in private hospitals (doctors, nursing staff, and administrative staff). The researcher has adopted a sampling method to collect data for the study. The appropriate statistical methods, such as Alpha Correlation Coefficient (ACC), Confirmatory Factor Analysis (CFA), and Multiple Regression Analysis (MRA), are used to analyze the data and test the hypotheses. The research has reached a number of results, the most important of which are (1) there is a statistical relationship between the independent variable represented by PL and the dependent variable represented by Organizational Success (OS). The paradoxical leader encourages employees to express their opinions and builds a work environment characterized by flexibility and independence. Also, the paradoxical leader works to support specialized work teams, which leads to the creation of new ideas, on the one hand, and contributes to the achievement of outstanding performance on the other hand. (2) the mentality of the paradoxical leader is flexible and capable of absorbing all suggestions from all employees. Also, the paradoxical leader is interested in enhancing cooperation among them and provides an opportunity to transfer experience and increase knowledge-sharing. Also, the sharing of knowledge creates the necessary diversity that helps the organization to obtain rich external information and enables the organization to deal with a rapidly changing environment. (3) The PL approach helps in facing the paradoxical demands of employees. A paradoxical leader plays an important role in reducing the feeling of instability in the work environment and lack of job security, reducing negative feelings for employees, restoring balance in the work environment, improving the well-being of employees, and increasing the degree of job satisfaction of employees in the organization. The study referred to a number of recommendations, the most important of which are (1) the leaders of the organizations must listen to the views of employees and their needs and move away from the official method of control. The leader should give sufficient freedom to employees to participate in decision-making and maintain enough space among them. The treatment between the leaders and employees must be based on friendliness, (2) the need for organizational leaders to pay attention to sharing knowledge among employees through training courses. The leader should make sure that every information provided by the employee is valuable and useful, which can be used to solve a problem that may face his/her colleagues at work, (3) the need for organizational leaders to pay attention to sharing knowledge among employees through brainstorming sessions. The leader should ensure that employees obtain knowledge from their colleagues and share ideas and information among them. This is in addition to motivating employees to complete their work in a new creative way, which leads to employees’ not feeling bored of repeating the same routine procedures in the organization.

Keywords: paradoxical leadership, organizational success, human resourece, management

Procedia PDF Downloads 58

Authors: Andrew Fox, Qingping Yang, Yuanhong Zhao, Tao Zhang

Abstract:

Furniture is a very significant subdivision of architecture and its inherent interior design activities. The furniture industry has developed from an artisan-driven craft industry, whose forerunners saw themselves manifested in their crafts and treasured a sense of pride in the creativity of their designs, these days largely reduced to an anonymous collective mass-produced output. Although a very conservative industry, there is great potential for the implementation of collaborative digital technologies allowing a reconfigured artisan experience to be reawakened in a new and exciting form. The furniture manufacturing industry, in general, has been slow to adopt new methodologies for a design using artificial and rule-based generative design. This tardiness has meant the loss of potential to enhance its capabilities in producing sustainable, flexible, and mass customizable ‘right first-time’ designs. This paper aims to demonstrate the concept methodology for the creation of alternative and inspiring aesthetic structures for robot-based additive manufacturing (RBAM). These technologies can enable the economic creation of previously unachievable structures, which traditionally would not have been commercially economic to manufacture. The integration of these technologies with the computing power of generative design provides the tools for practitioners to create concepts which are well beyond the insight of even the most accomplished traditional design teams. This paper aims to address the problem by introducing generative design methodologies employing the Autodesk Fusion 360 platform. Examination of the alternative methods for its use has the potential to significantly reduce the estimated 80% contribution to environmental impact at the initial design phase. Though predominantly a design methodology, generative design combined with RBAM has the potential to leverage many lean manufacturing and quality assurance benefits, enhancing the efficiency and agility of modern furniture manufacturing. Through a case study examination of a furniture artifact, the results will be compared to a traditionally designed and manufactured product employing the Ecochain Mobius product life cycle analysis (LCA) platform. This will highlight the benefits of both generative design and robot-based additive manufacturing from an environmental impact and manufacturing efficiency standpoint. These step changes in design methodology and environmental assessment have the potential to revolutionise the design to manufacturing workflow, giving momentum to the concept of conceiving a pre-industrial model of manufacturing, with the global demand for a circular economy and bespoke sustainable design at its heart.

Keywords: robot, manufacturing, generative design, sustainability, circular econonmy, product life cycle assessment, furniture

Procedia PDF Downloads 141

Authors: Sara Bahariderakhshan, Morteza Ahmadifar

Abstract:

Leakage is one of the most important problems that water distribution networks face which first reason is high-pressure existence. There are many approaches to control this excess pressure, which using pressure reducing valves (PRVs) or reducing pipe diameter are ones. In the other hand, Pumps are using electricity or fossil fuels to supply needed pressure in distribution networks but excess pressure are made in some branches due to topology problems and water networks’ variables therefore using pressure valves will be inevitable. Although using PRVs is inevitable but it leads to waste electricity or fuels used by pumps because PRVs just waste excess hydraulic pressure to lower it. Pumps working in reverse or Pumps as Turbine (called PaT in this article) are easily available and also effective sources of reducing the equipment cost in small hydropower plants. Urban areas of developing countries are facing increasing in area and maybe water scarcity in near future. These cities need wider water networks which make it hard to predict, control and have a better operation in the urban water cycle. Using more energy and, therefore, more pollution, slower repairing services, more user dissatisfaction and more leakage are these networks’ serious problems. Therefore, more effective systems are needed to monitor and act in these complicated networks than what is used now. In this article a new approach is proposed and evaluated: Using PAT to produce enough energy for remote valves and sensors in the water network. These sensors can be used to determine the discharge, pressure, water quality and other important network characteristics. With the help of remote valves pipeline discharge can be controlled so Instead of wasting excess hydraulic pressure which may be destructive in some cases, obtaining extra pressure from pipeline and producing clean electricity used by remote instruments is this articles’ goal. Furthermore due to increasing the area of the network there is unwanted high pressure in some critical points which is not destructive but lowering the pressure results to longer lifetime for pipeline networks without users’ dissatisfaction. This strategy proposed in this article, leads to use PaT widely for pressure containment and producing energy needed for remote valves and sensors like what happens in supervisory control and data acquisition (SCADA) systems which make it easy for us to monitor, receive data from urban water cycle and make any needed changes in discharge and pressure of pipelines easily and remotely. This is a clean project of energy production without significant environmental impacts and can be used in urban drinking water networks, without any problem for consumers which leads to a stable and dynamic network which lowers leakage and pollution.

Keywords: new energies, pump as turbine, drinking water, distribution network, remote control equipments

Procedia PDF Downloads 463

Authors: Kumlachew Zelalem Walle, Chun-Chen Yang

Abstract:

Solid-state lithium metal batteries (SSLMBs) are considered promising candidates for next-generation energy storage devices due to their superior energy density and excellent safety. However, recent findings have shown that the formation of lithium (Li) dendrites in SSLMBs still exhibits a terrible growth ability, which makes the development of SSLMBs have to face the challenges posed by the Li dendrite problem. In this work, an inorganic/organic mixture coating material (g-C3N4/ZIF-8/PVDF) was used to modify the surface of lithium metal anode (LMA). Then the modified LMA (denoted as g-C₃N₄@Li) was assembled with lithium nafion (LiNf) coated commercial NCM811 (LiNf@NCM811) using a bilayer hybrid solid electrolyte (Bi-HSE) that incorporated 20 wt.% (vs. polymer) LiNf coated Li6.05Ga0.25La3Zr2O11.8F0.2 ([email protected]) filler faced to the positive electrode and the other layer with 80 wt.% (vs. polymer) filler content faced to the g-C₃N₄@Li. The garnet-type Li6.05Ga0.25La3Zr2O11.8F0.2 (LG0.25LZOF) solid electrolyte was prepared via co-precipitation reaction process from Taylor flow reactor and modified using lithium nafion (LiNf), a Li-ion conducting polymer. The Bi-HSE exhibited high ionic conductivity of 6.8  10–4 S cm–1 at room temperature, and a wide electrochemical window (0–5.0 V vs. Li/Li+). The coin cell was charged between 2.8 to 4.5 V at 0.2C and delivered an initial specific discharge capacity of 194.3 mAh g–1 and after 100 cycles it maintained 81.8% of its initial capacity at room temperature. The presence of a nano-sheet g-C3N4/ZIF-8/PVDF as a composite coating material on the LMA surface suppress the dendrite growth and enhance the compatibility as well as the interfacial contact between anode/electrolyte membrane. The g-C3N4@Li symmetrical cells incorporating this hybrid electrolyte possessed excellent interfacial stability over 1000 h at 0.1 mA cm–2 and a high critical current density (1 mA cm–2). Moreover, the in-situ formation of Li3N on the solid electrolyte interface (SEI) layer as depicted from the XPS result also improves the ionic conductivity and interface contact during the charge/discharge process. Therefore, these novel multi-layered fabrication strategies of hybrid/composite solid electrolyte membranes and modification of the LMA surface using mixed coating materials have potential applications in the preparation of highly safe high-voltage cathodes for SSLMBs.

Keywords: high-voltage cathodes, hybrid solid electrolytes, garnet, graphitic-carbon nitride (g-C3N4), ZIF-8 MOF

Procedia PDF Downloads 68

Authors: Norhayati Ayob, Shamsu Mohamad

Abstract:

This paper aims to provide an initial background of the process of making traditional ceramic pottery, focusing on the materials and the influence of culture heritage. Ceramic pottery is one of the hallmarks of Sabah’s heirloom, not only use as cooking and storage containers but also closely linked with folk cultures and heritage. The Bajau Laut ethnic community of Semporna or better known as the Sea Gypsies, mostly are boat dwellers and work as fishermen in the coast. This ethnic community is famous for their own artistic traditional heirloom, especially the traditional hand-made clay stove called Lapohan. It is found that in the daily life of Bajau Laut community, Lapohan (clay stove) is used to prepare the meal and as a food warmer while they are at the sea. Besides, Lapohan pottery conveys symbolic meaning of natural objects, which portrays the identity, and values of Bajau Laut community. It is acknowledged that the basic process of making potterywares was much the same for people all across the world, nevertheless, it is crucial to consider that different ethnic groups may have their own styles and choices of raw materials. Furthermore, it is still unknown why and how the Bajau Laut ethnic of Semporna get started making their own pottery and to survive until today by heavily depending on the raw materials available in Semporna. In addition, the emergent problem faced by the pottery maker in Sabah is the absence of young successor to continue the heirloom legacy. Therefore, this research aims to explore the traditional pottery making in Sabah, by investigating the background history of Lapohan pottery and to propose the classification of Lapohan based on design and motifs of traditional pottery that will be recognised throughout the study. It is postulated that different techniques and forms of making traditional pottery may produce different types of pottery in terms of surface decoration, shape, and size that portrays different cultures. This study will be conducted at Selakan Island, Semporna, which is the only location that still has Lapohan making. This study is also based on the chronological process of making pottery and taboos of the process of preparing the clay, forming, decoration technique, motif application and firing techniques. The relevant information for the study will be gathered from field study, including observation, in-depth interview and video recording. In-depth interviews will be conducted with several potters and the conversation and pottery making process will be recorded in order to understand the actual process of making Lapohan. The findings hope to provide several types of Lapohan based on different designs and cultures, for example, the one with flat-shape design or has round-shape on the top of clay stove will be labeled with suitable name based on their culture. In conclusion, it is hoped that this study will contribute to conservation for traditional pottery making in Sabah as well as to preserve their culture and heirloom for future generations.

Keywords: Bajau Laut, culture, Lapohan, traditional pottery

Procedia PDF Downloads 188

Authors: David Schafer

Abstract:

Critical Theory is in sore need of a workable account of technology. It had one in the writings of Herbert Marcuse, or so it seemed until Jürgen Habermas mounted a critique in 'Technology and Science as Ideology' (Habermas, 1970) that decisively put it away. Ever since Marcuse’s work has been regarded outdated – a 'philosophy of consciousness' no longer seriously tenable. But with Marcuse’s view has gone the important insight that technology is no norm-free system (as Habermas portrays it) but can be laden with social bias. Andrew Feenberg is among a few serious scholars who have perceived this problem in post-Habermasian critical theory and has sought to revive a basically Marcusean account of technology. On his view, while so-called ‘technical elements’ that physically make up technologies are neutral with regard to social interests, there is a sense in which we may speak of a normative grammar or ‘technical code’ built-in to technology that can be socially biased in favor of certain groups over others (Feenberg, 2002). According to Feenberg, those perspectives on technology are reified which consider technology only by their technical elements to the neglect of their technical codes. Nevertheless, Feenberg’s account fails to explain what is normatively problematic with such reified views of technology. His plausible claim that they represent false perspectives on technology by itself does not explain how such views may be oppressive, even though Feenberg surely wants to be doing that stronger level of normative theorizing. Perceiving this deficit in his own account of reification, he tries to adopt Habermas’s version of systems-theory to ground his own critical theory of technology (Feenberg, 1999). But this is a curious move in light of Feenberg’s own legitimate critiques of Habermas’s portrayals of technology as reified or ‘norm-free.’ This paper argues that a better foundation may be found in Axel Honneth’s recent text, Freedom’s Right (Honneth, 2014). Though Honneth there says little explicitly about technology, he offers an implicit account of reification formulated in opposition to Habermas’s systems-theoretic approach. On this ‘normative functionalist’ account of reification, social spheres are reified when participants prioritize individualist ideals of freedom (moral and legal freedom) to the neglect of an intersubjective form of freedom-through-recognition that Honneth calls ‘social freedom.’ Such misprioritization is ultimately problematic because it is unsustainable: individual freedom is philosophically and institutionally dependent upon social freedom. The main difficulty in adopting Honneth’s social theory for the purposes of a theory of technology, however, is that the notion of social freedom is predicable only of social institutions, whereas it appears difficult to conceive of technology as an institution. Nevertheless, in light of Feenberg’s work, the idea that technology includes within itself a normative grammar (technical code) takes on much plausibility. To the extent that this normative grammar may be understood by the category of social freedom, Honneth’s dialectical account of the relationship between individual and social forms of freedom provides a more solid basis from which to ground the normative claims of Feenberg’s sociological account of technology than Habermas’s systems theory.

Keywords: Habermas, Honneth, technology, Feenberg

Procedia PDF Downloads 198

Authors: Andreas Kapardis, Maria Krambia-Kapardis, Sofia Michaelides-Mateou

Abstract:

Corruption and economic crime is a serious problem affecting the sustainability of businesses in the 21st century. Nowadays, many corruption or fraud cases come to light thanks to whistleblowers. This article will first discuss the concept of whistleblowing as well as some relevant legislation enacted around the world. Secondly, it will discuss the findings of a survey of whistleblowers or could-have-been whistleblowers. Finally, suggestions for the development of a comprehensive whistleblowing framework will be considered. Whistleblowing can be described as expressing a concern about a wrongdoing within an organization, such as a corporation, an association, an institution or a union. Such concern must be in the public interest and in good faith and should relate to the cover up of matters that could potentially result in a miscarriage of justice, a crime, criminal offence and threats to health and safety. Whistleblowing has proven to be an effective anti-corruption mechanism and a powerful tool that helps deterring fraud, violations, and malpractices within organizations, corporations and the public sector. Research in the field of whistleblowing has concentrated on the reasons for whistleblowing and financial bounties; the effectiveness of whistleblowing; whistleblowing being a prosocial behavior with a psychological perspective and consequences; as a tool in protecting shareholders, saving lives and billions of dollars of public funds. Whilst, no other study of whistleblowing has been carried out on whistleblowers or intended whistleblowers. The study reported in the current paper analyses the findings of 74 whistleblowers or intended whistleblowers, the reasons behind their decision to blow the whistle, or not to proceed to blow the whistle and any regrets they may have had. In addition a profile of a whistleblower is developed concerning their age, gender, marital and family status and position in an organization. Lessons learned from the intended whistleblowers and in response to the questions if they would be willing to blow the whistle again show that enacting legislation to protect the whistleblower is not enough. Similarly, rewarding the whistleblower does not appear to provide the whistleblower with an incentive since the majority noted that “work ethics is more important than financial rewards”. We recommend the development of a comprehensive and holistic framework for the protection of the whistleblower and to ensure that remedial actions are immediately taken once a whistleblower comes forward. The suggested framework comprises (a) hard legislation in ensuring the whistleblowers follow certain principles when blowing the whistle and, in return, are protected for a period of 5 years from being fired, dismissed, bullied, harassed; (b) soft legislation in establishing an agency to firstly ensure psychological and legal advice is provided to the whistleblowers and secondly any required remedial action is immediately taken to avert the undesirable events reported by a whistleblower from occurring and, finally; (c) mechanisms to ensure the coordination of actions taken.

Keywords: whistleblowing, business ethics, legislation, business

Procedia PDF Downloads 309

Authors: Morteza Ahmadifar, Sarah Bahari Derakhshan

Abstract:

Leakage is one of the most important problems that water distribution networks face which first reason is high-pressure existence. There are many approaches to control this excess pressure, which using pressure reducing valves (PRVs) or reducing pipe diameter are ones. On the other hand, Pumps are using electricity or fossil fuels to supply needed pressure in distribution networks but excess pressure are made in some branches due to topology problems and water networks’ variables, therefore using pressure valves will be inevitable. Although using PRVs is inevitable but it leads to waste electricity or fuels used by pumps because PRVs just waste excess hydraulic pressure to lower it. Pumps working in reverse or Pumps as Turbine (called PAT in this article) are easily available and also effective sources of reducing the equipment cost in small hydropower plants. Urban areas of developing countries are facing increasing in area and maybe water scarcity in near future. These cities need wider water networks which make it hard to predict, control and have a better operation in the urban water cycle. Using more energy and therefore more pollution, slower repairing services, more user dissatisfaction and more leakage are these networks’ serious problems. Therefore, more effective systems are needed to monitor and act in these complicated networks than what is used now. In this article a new approach is proposed and evaluated: Using PAT to produce enough energy for remote valves and sensors in the water network. These sensors can be used to determine the discharge, pressure, water quality and other important network characteristics. With the help of remote valves pipeline discharge can be controlled so Instead of wasting excess hydraulic pressure which may be destructive in some cases, obtaining extra pressure from pipeline and producing clean electricity used by remote instruments is this articles’ goal. Furthermore, due to increasing the area of network there is unwanted high pressure in some critical points which is not destructive but lowering the pressure results to longer lifetime for pipeline networks without users’ dissatisfaction. This strategy proposed in this article, leads to use PAT widely for pressure containment and producing energy needed for remote valves and sensors like what happens in supervisory control and data acquisition (SCADA) systems which make it easy for us to monitor, receive data from urban water cycle and make any needed changes in discharge and pressure of pipelines easily and remotely. This is a clean project of energy production without significant environmental impacts and can be used in urban drinking water networks, without any problem for consumers which leads to a stable and dynamic network which lowers leakage and pollution.

Keywords: clean energies, pump as turbine, remote control, urban water distribution network

Procedia PDF Downloads 394

Authors: Birsel Canan Demirbag, Kıymet Yesilcicek Calik, Hacer Kobya Bulut

Abstract:

Objective: This study was conducted to evaluate the problems of women over 65 with incontinence diagnosis. Methods: This descriptive study was conducted with women over 65 with incontinence diagnosis in four Family Health Centers in a city in Eastern Black Sea region between November 1, and December 20, 2015. 203, 107, 178, 180 women over 65 were registered in these centers and 262 had incontinence diagnosis at least once and had an ongoing complaint. 177 women were volunteers for the study. During home visits and using face-to-face survey methodology, participants were given socio-demographic characteristics survey, Sandvik severity scale, Incontinence Quality of Life Scale, Urogenital Distress Inventory and a questionnaire including challenges experienced due to incontinence developed by the researcher. Data were analyzed with SPSS program using percentages, numbers, Chi-square, Man-Whitney U and t test with 95% confidence interval and a significance level p <0.05. Findings: 67 ± 1.4 was the mean age, 2.05 ± 0.04 was parity, 44.5 ± 2.12 was menopause age, 66.3% were primary school graduates, 45.7% had deceased spouse, 44.4% lived in a large family, 67.2% had their own room, 77.8% had income, 89.2% could meet self- care, 73.2% had a diagnosis of mixed incontinence, 87.5% suffered for 6-20 years % 78.2 had diuretics, antidepressants and heart medicines, 20.5% had urinary fecal cases, 80.5% had bladder training at least once, 90.1% didn’t have bladder diary calendar/control training programs, 31.1% had hysterectomy for prolapse, 97.1'i% was treated with lower urinary tract infection at least once, 66.3% saw a doctor to get drug in the last three months, 76.2 could not go out alone, 99.2 % had at least one chronic disease, 87.6 % had constipation complain, 2.9% had chronic cough., 45.1% fell due to a sudden rise for toilet. Incontinence Impact Questionnaire Average score was (QOL) 54.3 ± 21.1, Sandvik score was 12.1 ± 2.5, Urogenital Distress Inventory was 47.7 ± 9.2. Difficulties experienced due to incontinence were 99.5% feeling of unhappiness, 67.1% constant feeling of urine smell due to failing to change briefs frequently, % 87.2 move away from social life, 89.7 unable to use pad, 99.2% feeling of disturbing households / other individuals, 87.5% feel dizziness/fall due to sudden rise, 87.4% feeling of others’ imperceptions about the situation, % 94.3 insomnia, 78.2 lack of assistance, 84.7% couldn’t afford urine protection briefs. Results: With this study, it was found out that there were a lot of unsolved issues at individual and community level affecting the life quality of women with incontinence. In accordance with this common problem in women, to facilitate daily life it is obvious that regular home care training programs at institutional level in our country will be effective.

Keywords: health problems, incontinence, incontinence quality of life questionnaire, old age, urinary urogenital distress inventory, Sandviken severity, women

Procedia PDF Downloads 321

Authors: Sofia Maria Poulimenou, Ioannis Deliyannis, Elisavet Filippidou, Stamatella Laboura

Abstract:

Smart technologies are being actively used to improve the experience of travel and promote or demote a destination’s reputation via a wide variety of social media applications and platforms. This paper conceptualises the design and deployment of smart management apps to promote culture, sustainability and accessibility within two destinations in Greece that represent the extremes of visiting scale. One is the densely visited Corfu, which is a UNESCO’s heritage site. The problems caused by the lack of organisation of the visiting experience and infrastructures affect all parties interacting within the site: visitors, citizens, public and private sector. Second is Kilkis, a low tourism destination with high seasonality and mostly inbound tourism. Here the issue faced is that traditional approaches to inform and motivate locals and visitors to explore and taste of the culture have not flourished. The problem is apprehended via the design and development of two systems named “Hologrammatic Corfu” for Corfu old town and “BRENDA” for the area of Kilkis. Although each system is designed independently, featuring different solutions to the problems, both approaches have been designed by the same team and a novel gaming and gamification methodology. The “Hologramatic Corfu” application has been designed, for the exploration of the site covering user requirments before, during and after the trip, with the use of transmedia content such as photos, 360-degree videos, augmented reality and hologrammatic videos. Also, a statistical analysis of travellers’ visits to specific points of interest is actively utilized enabling visitors to dynamically re-rooted during their visit, safeguarding sustainability and accessibility and inclusivity along the entire tourism cycle. “BRENDA” is designed specifically to promote gastronomic and historical tourism. This serious game implements and combines gaming and gamification elements in order to connect local businesses with cultural points of interest. As the environment of the project has a strong touristic orientation, “BRENDA” supports food-related gamified processes and historical games involving active participation of both local communities (content providers) and visitors (players) which are more likely to be successfully performed in the informal environment of travelling and promote sustainable tourism experiences. Finally, the paper presents the ability to re-use existing gaming components within new areas of interest via minimal adaptation and the use of transmedia aspects that enables destinations to be rebranded into smart destinations.

Keywords: smart tourism, gamification, user experience, transmedia content

Procedia PDF Downloads 173

Authors: B. S. Premalatha, Kausalya Sahani

Abstract:

Background: Voice is multidimensional which convey emotion, feelings, and communication. Voice disorders have an adverse effect on the physical, emotional and functional domains of an individual. Self-rating by clients about their voice problem helps the clinicians to plan intervention strategies. Voice handicap index is one such self-rating scale contains 30 questions that quantify the functional, physical and emotional impacts of a voice disorder on a patient’s quality of life. Each subsection has 10 questions. Though adapted and validated versions of VHI are available in other Indian languages but not in Telugu, which is a Dravidian language native to India. It is mainly spoken in Andhra Pradesh and neighbouring states in southern India. Objectives: To adapt and validate the English version of Voice Handicap Index (VHI) into Telugu language and evaluate its internal consistency and clinical validate in Telugu speaking population. Materials: The study carried out in three stages. First stage was a forward translation of English version of VHI, was given to ten experts, who were well proficient in writing and reading Telugu and five speech-language pathologists to translate into Telugu. Second Stage was backward translation where translated version of Telugu was given to a different group of ten experts (who were well proficient in writing and reading Telugu) and five speech-language pathologists who were native Telugu speakers and had good proficiency in Telugu and English. The third stage was an administration of translated version on Telugu to the targeted population. Totally 40 clinical subjects and 40 normal controls served as participants, and each group had 26 males and 14 females’ age range of 20 to 60 years. Clinical group comprised of individuals with laryngectomee with the Tracheoesophageal puncture (n=18), laryngitis (n=11), vocal nodules (n=7) and vocal fold palsy (n=4). Participants were asked to mark of their each experience on a 5 point equal appearing scale (0=never, 1=almost never, 2=sometimes, 3=almost always, 4=always) with a maximum total score of 120. Results: Statistical analysis was made by using SPSS software (22.0.0 Version). Mean, standard deviation and percentage (%) were calculated all the participants for both the groups. Internal consistency of VHI in Telugu was found to be excellent with the consistency scores for all the domains such as physical, emotional and functional are 0.742, 0.934and 0.938. The validity of scores showed a significant difference between clinical population and control group for domains like physical, emotional and functional and total scores. P value found to be less than 0.001( < 0.001). Negative correlation found in age and gender among self-domains such as physical, emotional and functional total scores in dysphonic and control group. Conclusion: The present study indicated that VHI in Telugu is able to discriminate participants having voice pathology from normal populations, which make this as a valid tool to collect information about their voice from the participants.

Keywords: adaptation, Telugu Version, translation, Voice Handicap Index (VHI)

Procedia PDF Downloads 277

Authors: M. Mashiur Rahman, Ulrik Birk Henriksen, Jesper Ahrenfeldt, Maria Puig Arnavat

Abstract:

Using biomass gasification to make producer gas is one of the promising sustainable energy options available for small scale plant and rural applications for power and electricity. Tar content in producer gas is the main problem if it is used directly as a fuel. A low-tar biomass (LTB) gasifier of approximately 30 kW capacity has been developed to solve this. Moving bed gasifier with internal recirculation of pyrolysis gas has been the basic principle of the LTB gasifier. The gasifier focuses on the concept of mixing the pyrolysis gases with gasifying air and burning the mixture in separate combustion chamber. Five tests were carried out with the use of wood pellets and wood chips separately, with moisture content of 9-34%. The LTB gasifier offers excellent opportunities for handling extremely low-tar in the producer gas. The gasifiers producer gas had an extremely low tar content of 21.2 mg/Nm³ (avg.) and an average lower heating value (LHV) of 4.69 MJ/Nm³. Tar content found in different tests in the ranges of 10.6-29.8 mg/Nm³. This low tar content makes the producer gas suitable for direct use in internal combustion engine. Using mass and energy balances, the average gasifier capacity and cold gas efficiency (CGE) observed 23.1 kW and 82.7% for wood chips, and 33.1 kW and 60.5% for wood pellets, respectively. Average heat loss in term of higher heating value (HHV) observed 3.2% of thermal input for wood chips and 1% for wood pellets, where heat loss was found 1% of thermal input in term of enthalpy. Thus, the LTB gasifier performs better compared to typical gasifiers in term of heat loss. Equivalence ratio (ER) in the range of 0.29 to 0.41 gives better performance in terms of heating value and CGE. The specific gas production yields at the above ER range were in the range of 2.1-3.2 Nm³/kg. Heating value and CGE changes proportionally with the producer gas yield. The average gas compositions (H₂-19%, CO-19%, CO₂-10%, CH₄-0.7% and N₂-51%) obtained for wood chips are higher than the typical producer gas composition. Again, the temperature profile of the LTB gasifier observed relatively low temperature compared to typical moving bed gasifier. The average partial oxidation zone temperature of 970°C observed for wood chips. The use of separate combustor in the partial oxidation zone substantially lowers the bed temperature to 750°C. During the test, the engine was started and operated completely with the producer gas. The engine operated well on the produced gas, and no deposits were observed in the engine afterwards. Part of the producer gas flow was used for engine operation, and corresponding electrical power was found to be 1.5 kW continuously, and maximum power of 2.5 kW was also observed, while maximum generator capacity is 3 kW. A thermodynamic equilibrium model is good agreement with the experimental results and correctly predicts the equilibrium bed temperature, gas composition, LHV of the producer gas and ER with the experimental data, when the heat loss of 4% of the energy input is considered.

Keywords: biomass gasification, low-tar biomass gasifier, tar elimination, engine, deposits, condensate

Procedia PDF Downloads 114

Authors: C. Miranda, S. Cunha, R. Soares, M. Maia, G. Igrejas, F. Silva, P. Poeta

Abstract:

The worldwide inappropriate use of antibiotics has increased the emergence of antimicrobial-resistant microorganisms isolated from animals, humans, food, and the environment. To combat this complex and multifaceted problem is essential to know the prevalence in livestock animals and possible ways of transmission among animals and between these and humans. Enterococci species, in particular E. faecalis and E. faecium, are the most common nosocomial bacteria, causing infections in animals and humans. Thus, the aim of this study was to characterize resistance and virulence factors genes among two enterococci species isolated from calf colostrums in Portuguese dairy farms. The 55 enterococci isolates (44 E. faecalis and 11 E. faecium) were tested for the presence of the resistance genes for the following antibiotics: erythromicyn (ermA, ermB, and ermC), tetracycline (tetL, tetM, tetK, and tetO), quinupristin/dalfopristin (vatD and vatE) and vancomycin (vanB). Of which, 25 isolates (15 E. faecalis and 10 E. faecium) were tested until now for 8 virulence factors genes (esp, ace, gelE, agg, cpd, cylA, cylB, and cylLL). The resistance and virulence genes were performed by PCR, using specific primers and conditions. Negative and positive controls were used in all PCR assays. All enterococci isolates showed resistance to erythromicyn and tetracycline through the presence of the genes: ermB (n=29, 53%), ermC (n=10, 18%), tetL (n=49, 89%), tetM (n=39, 71%) and tetK (n=33, 60%). Only two (4%) E. faecalis isolates showed the presence of tetO gene. No resistance genes for vancomycin were found. The virulence genes detected in both species were cpd (n=17, 68%), agg (n=16, 64%), ace (n=15, 60%), esp (n=13, 52%), gelE (n=13, 52%) and cylLL (n=8, 32%). In general, each isolate showed at least three virulence genes. In three E. faecalis isolates was not found virulence genes and only E. faecalis isolates showed virulence genes for cylA (n=4, 16%) and cylB (n=6, 24%). In conclusion, these colostrum samples that were consumed by calves demonstrated the presence of antibiotic-resistant enterococci harbored virulence genes. This genotypic characterization is crucial to control the antibiotic-resistant bacteria through the implementation of restricts measures safeguarding public health. Acknowledgements: This work was funded by the R&D Project CAREBIO2 (Comparative assessment of antimicrobial resistance in environmental biofilms through proteomics - towards innovative theragnostic biomarkers), with reference NORTE-01-0145-FEDER-030101 and PTDC/SAU-INF/30101/2017, financed by the European Regional Development Fund (ERDF) through the Northern Regional Operational Program (NORTE 2020) and the Foundation for Science and Technology (FCT). This work was supported by the Associate Laboratory for Green Chemistry - LAQV which is financed by national funds from FCT/MCTES (UIDB/50006/2020 and UIDP/50006/2020).

Keywords: antimicrobial resistance, calf, colostrums, enterococci

Procedia PDF Downloads 199

Authors: Merav Meiron-Goren, Orna Braun-Lewensohn, Tal Litvak-Hirsh

Abstract:

In recent years, there has been an increasing tendency towards separation and divorce in relationships. Nevertheless, many couples in a first marriage do not anticipate this as a probable possibility and do not make any preparation for it. Same sex couples establishing a family encounter a much more complicated situation than do heterosexual couples. Although there is a trend towards legal recognition of same sex marriage, many countries, including Israel, do not recognize it. The absence of legal recognition or the existence of partial recognition creates complexity for these couples. They have to fight for their right to establish a family, like the recognition of the biological child of a woman, as a child of her woman spouse too, or the option of surrogacy for a male couple who want children, and more. The lack of legal recognition is burden on the lives of these couples. In the absence of clear norms regarding the conduct of the family unit, the couples must define for themselves the family structure, and deal with everyday dilemmas that lack institutional solutions. This may increase the friction between the two couple members, and it is one of the factors that make it difficult for them to maintain the relationship. This complexity exists, perhaps even more so, in separation. The end of relationship is often accompanied by a deep crisis, causing pain and stress. In most cases, there are also other conflicts that must be settled. These are more complicated when rights are in doubt or do not exist at all. Complex issues for separating same sex couples may include matters of property, recognition of parenthood, and care and support for the children. The significance of the study is based on the fact that same sex relationships are becoming more and more widespread, and are an integral part of the society. Even so, there is still an absence of research focusing on such relationships and their ending. The objective of the study is to research the perceptions of same sex couples regarding the possibility of separation, preparing for it, conflict management and resolving disputes through the separation process. It is also important to understand the point of view of couples that have gone through separation, how they coped with the emotional and practical difficulties involved in the separation process. The doctoral research will use a qualitative research method in a phenomenological approach, based on semi-structured in-depth interviews. The interviewees will be divided into three groups- at the beginning of a relationship, during the separation crisis and after separation, with a time perspective, with about 10 couples from each group. The main theoretical model serving as the basis of the study will be the Lazarus and Folkman theory of coping with stress. This model deals with the coping process, including cognitive appraisal of an experience as stressful, appraisal of the coping resources, and using strategies of coping. The strategies are divided into two main groups, emotion-focused forms of coping and problem-focused forms of coping.

Keywords: conflict management, coping, legal recognition, same-sex relationship, separation

Procedia PDF Downloads 142

Authors: Emma S. Bowers

Abstract:

Perturbations in global environments and temperatures have heightened the urgency of creating cost-efficient, energy-neutral building techniques. Structural responses to this thermal crisis have included designs (including those of the building standard PassivHaus) with airtightness, window placement, insulation, solar orientation, shading, and heat-exchange ventilators as potential solutions or interventions. Limitations in the predictability of the circulation of cooled air through the ambient temperature gradients throughout a structure are one of the major obstacles facing these enhanced building methods. A diverse range of air-cooling devices utilizing varying technologies is implemented around the world. Many of them worsen the problem of climate change by consuming energy. Using natural ventilation principles of air buoyancy and density to circulate fresh air throughout a building with no energy input can combat these obstacles. A unique prototype of an energy-neutral air-circulation system was constructed in order to investigate potential temperature and pressure gradients related to the stack effect (updraft of air through a building due to changes in air pressure). The stack effect principle maintains that since warmer air rises, it will leave an area of low pressure that cooler air will rush in to fill. The result is that warmer air will be expelled from the top of the building as cooler air is directed through the bottom, creating an updraft. Stack effect can be amplified by cooling the air near the bottom of a building and heating the air near the top. Using readily available, mostly recyclable or biodegradable materials, an insulated building module was constructed. A tri-part construction model was utilized: a subterranean earth-tube heat exchanger constructed of PVC pipe and placed in a horizontally oriented trench, an insulated, airtight cube aboveground to represent a building, and a solar chimney (painted black to increase heat in the out-going air). Pressure and temperature sensors were placed at four different heights within the module as well as outside, and data was collected for a period of 21 days. The air pressures and temperatures over the course of the experiment were compared and averaged. The promise of this design is that it represents a novel approach which directly addresses the obstacles of air flow and expense, using the physical principle of stack effect to draw a continuous supply of fresh air through the structure, using low-cost and readily available materials (and zero manufactured energy). This design serves as a model for novel approaches to creating temperature controlled buildings using zero energy and opens the door for future research into the effects of increasing module scale, increasing length and depth of the earth tube, and shading the building. (Model can be provided).

Keywords: air circulation, PassivHaus, stack effect, thermal gradient

Procedia PDF Downloads 154

Authors: Soowon Park, Min-Ji Kim, Jun-Young Lee

Abstract:

Motivation: The stigma of mental illness has been studied in many disciplines, including social psychology, counseling psychology, sociology, psychiatry, public health care, and related areas, because individuals labeled as ‘mentally ill’ are often deprived of their rights and their life opportunities. To understand the factors that deepen the stigma of mental illness, it is important to understand the influencing factors of the stigma. Problem statement: Depression is a common disorder in adults, but the incidence of help-seeking is low. Researchers have believed that this poor help-seeking behavior is related to the stigma of mental illness, which results from low mental health literacy. However, it is uncertain that increasing mental health literacy decreases mental health stigmatization. Furthermore, even though decreasing stigmatization is important, the stigma of mental illness is still a stable and long-lasting phenomenon. Thus, factors other than knowledge about mental disorders have the power to maintain the stigma. Investigating the influencing factors that facilitate the stigma of psychiatric disease could help lower the social stigmatization. Approach: Face-to-face interviews were conducted with a multi-clustering sample. A total of 700 Korean participants (38% male), ranging in age from 18 to 78 (M(SD)age= 48.5(15.7)) answered demographical questions, Korean version of Link’s Perceived Devaluation and Discrimination (PDD) scale for the assessment of social stigmatization against depression, and the Korean version of the WHO-Composite International Diagnostic Interview for the assessment of mental disorders. Multiple-regression was conducted to find the predicting factors of social stigmatization against depression. Ages, sex, years of education, income, living location, and experience of mental illness were used as the predictors. Results: Predictors accounted for 14% of the variance in the stigma of depressive disorders (F(6, 693) = 20.27, p < .001). Among those, only age, years of education, and experience of mental illness significantly predicted social stigmatization against depression. The standardized regression coefficient of age had a negative association with stigmatization (β = -.20, p < .001), but years of education (β = .20, p < .001) and experience of mental illness (β = .08, p < .05) positively predicted depression stigmatization. Conclusions: The present study clearly demonstrates the association between personal factors and depressive disorder stigmatization. Younger age, more education, and self-stigma appeared to increase the stigmatization. Young, highly educated, and mentally ill people tend to reject patients with depressive disorder as friends, teachers, or babysitters; they also tend to think that those patients have lower intelligence and abilities. These results suggest the possibility that people from a high social class, or highly educated people, who have the power to make decisions, help maintain the social stigma against mental illness patients. To increase the awareness that people from high social classes have more stigmatization against depressive disorders will help decrease the biased attitudes against mentally ill patients.

Keywords: depressive disorder stigmatization, age, education, self-stigma

Procedia PDF Downloads 405

Authors: José Carlos Bronze, Carlinda Leite, Angélica Monteiro

Abstract:

The creation of the Erasmus Program in 1987 represented a milestone in promoting and funding international mobility in higher education in Europe. Its effects were so significant that they influenced the creation of the European Higher Education Area through the Bologna Process and ensured the program’s continuation and maintenance. Over the last decades, the escalating figures of participants and funds instigated significant scientific studies on the program's effects on higher education. More recently, in 2014, the program was renamed “Erasmus+” when it expanded into other fields of education, namely Vocational Education and Training (VET). Despite being now running in this field of education for a decade (2014-2024), its effects on VET remain less studied and less known, while the higher education field keeps attracting researchers’ attention. Given this gap, it becomes relevant to study the effects of E+ on VET, particularly in the priority domains of the Program: “Inclusion and Diversity,” “Participation in Democratic Life, Common Values and Civic Engagement,” “Environment and Fight Against Climate Change,” and “Digital Transformation.” This latter has been recently emphasized due to the COVID-19 pandemic that forced the so-called emergency remote teaching, leading schools to quickly transform and adapt to a new reality regardless of the preparedness levels of teachers and students. Together with the remaining E+ priorities, they directly relate to an emancipatory perspective of education sustained in soft skills such as critical thinking, intercultural awareness, autonomy, active citizenship, teamwork, and problem-solving, among others. Based on this situation, it is relevant to know the effects of E+ on the VET field, namely questioning how international mobility instigates digitalization processes and supports emancipatory queries therein. As an education field that more directly connects to hard skills and an instrumental approach oriented to the labor market’s needs, a study was conducted to determine the effects of international mobility on developing digital literacy and soft skills in the VET field. In methodological terms, the study used semi-structured interviews with teaching and non-teaching staff from three VET schools who are strongly active in the E+ Program. The interviewees were three headmasters, four mobility project managers, and eight teachers experienced in international mobility. The data was subjected to qualitative content analysis using the NVivo 14 application. The results show that E+ international mobility promotes and facilitates the use of digital technologies as a pedagogical resource at VET schools and enhances and generates students’ soft skills. In conclusion, E+ mobility in the VET field supports adopting the program’s priorities by increasing the teachers’ knowledge and use of digital resources and amplifying and generating participants’ soft skills.

Keywords: Erasmus international mobility, digital literacy, soft skills, vocational education and training

Procedia PDF Downloads 32