Search results for: Darius K. S Chan

Authors: Mantas Sriubas, Kristina Bockute, Darius Virbukas, Giedrius Laukaitis

Abstract:

In this work, the doped TiO2 (dopants – Ca, Mg) was investigated. The comparison between the physical vapour deposition methods as electron beam vapour deposition and magnetron sputtering was performed and the structural and electrical properties of the formed thin films were investigated. Thin films were deposited on different type of substrates: SiO2, Alloy 600 (Fe-Ni-Cr) and Al2O3 substrates. The structural properties were investigated using Ambios XP-200 profilometer, scanning electron microscope (SEM) Hitachi S-3400N, X-ray energy-dispersive spectroscope (EDS) Quad 5040 (Bruker AXS Microanalysis GmbH), X-ray diffractometer (XRD) D8 Discover (Bruker AXS GmbH) with glancing angles focusing geometry in a 20 – 70° range using the Cu Kα1 λ = 0.1540562 nm radiation). The impedance spectroscopy measurements were performed using Probostat® (NorECs AS) measurement cell in the frequency range from 10-1-106 Hz under reducing and oxidizing conditions in temperature range of 200 °C to 1200 °C. The investigation of the e-beam deposited Ca and Mg doped-TiO2 thin films shows that the thin films are dense without any visible pores and cavities and the thin films grow in zone T according Barna-Adamik SZM. Substrate temperature was kept 600 °C during the deposition and Ts/Tm ≈ 0.32 (substrate temperature (Ts) and coating material melting temperature (Tm)). The surface diffusion is high however, the grain boundary migration is strongly limited at this temperature. This means that structure is inhomogeneous and the columnar structure is mostly visible in the upper part of the films. According to XRD, the increasing of the Ca dopants’ concentration increases the crystallinity of the formed thin films and the crystallites size increase linearly and Ca dopants act as prohibitors. Thin films are comprised of anatase TiO2 phase with an exception of 2 % Ca doped TiO2, where a small peak of Ca arise. In the case of Mg doped-TiO2 the intensities of the XRD peaks decreases with increasing Mg molar concentration. It means that there are less diffraction planes of the particular orientation in thin films with higher impurities concentration. Thus, the crystallinity decreases with increasing Mg concentration and Mg dopants act as inhibitors. The impedance measurements show that the dopants changed the conductivity of the formed thin films. The conductivity varies from 10-3 S/cm to 10-4 S/cm at 800 °C under wet reducing conditions. The microstructure of the magnetron sputtered thin TiO2 films is different comparing to the thin films deposited using e-beam deposition therefore influencing other structural and electrical properties.

Keywords: electrical properties, electron beam deposition, magnetron sputtering, microstructure, titanium dioxide

Procedia PDF Downloads 297

Authors: Gou-Moon Choi, Woo-Young Jung, Chan-Young Yune

Abstract:

Recently, the natural disaster has increased worldwide. In Korea, the damage to life and property caused by a typhoon, heavy rain, heavy snow, and an extreme wind also increases every year. Among natural disasters, the frequency and the strength of wind have increased because sea surface temperature has risen due to the increase of the average temperature of the Earth. In the case of extreme wind disaster, it is impossible to control or reduce the occurrence, and the recovery cost always exceeds the damage cost. Therefore, quantitative estimation of the damage cost for extreme wind needs to be established beforehand to install proactive countermeasures. In this study, the damage cost for private properties was analyzed based on the data for the past 10 years in Korea. The damage cost curve was also suggested for the metropolitan cities and provinces. The result shows the possibility for the regional application of the damage cost curve because the damage cost of the regional area is estimated based on the cost of cities and provinces.

Keywords: damage cost, extreme wind, natural disaster, private property

Procedia PDF Downloads 305

Authors: Edward C. W. Chan, Benny C. F. Cheung

Abstract:

In the knowledge economy, the financial indicator is not the unique instrument to gauge the performance of a company. The role of intellectual capital contributing to the company performance is increasing. To measure the company performance due to intellectual capital, the value-added intellectual capital (VAIC) model is adopted to measure the intellectual capital utilisation efficiency of the subject companies. The purpose of this study is to review the readiness of measuring intellectual capital for the Hong Kong listed companies in the property development and property investment industry by using VAIC model. This study covers the financial reports from the representative Hong Kong listed property development companies and property investment companies in the period 2014-2019. The findings from this study indicated the industry is ready for IC measurement employing VAIC framework but not yet ready for using the extended VAIC model.

Keywords: intellectual capital, intellectual capital measurement, property development, property investment, Skandia navigator, VAIC

Procedia PDF Downloads 115

Authors: John Chan, Jake Linnenbank, Gavin Caird

Abstract:

Automatic Selective Door Operation (ASDO) systems are increasingly used in railways to provide Correct Side Door Enable (CSDE) protection as well as to protect passenger doors opening off the platform where the train is longer than the platform, or in overshoot or undershoot scenarios. Such ASDO systems typically utilise trackside-installed RFID beacons, such as Eurobalises for odometry positioning purposes. Installing such trackside infrastructure may not be desirable or possible due to various factors such as conflict with existing infrastructure, potential damage from track tamping and jurisdiction constraints. Ultra-wideband (UWB) positioning technology could enable ASDO positioning requirements to be met without requiring installation of equipment directly on track since UWB technology can be installed on adjacent infrastructure such as on platforms. This paper will explore the feasibility of upgrading existing ASDO systems with UWB positioning technology, the feasibility of retrofitting UWB-enabled ASDO systems onto unfitted trains, and any other considerations relating to the use of UWB positioning for ASDO applications.

Keywords: UWB, ASDO, automatic selective door operations, CSDE, correct side door enable

Procedia PDF Downloads 77

Authors: Joon-Hyung Kim, Him-Chan Lee, Jin-Hyuk Kim, Yong-Kab Lee, Young-Seok Choi

Abstract:

The crude oil in an oil well exists in various phases such as gas, seawater, and sand, as well as oil. Therefore, a phase separator is needed at the front of a single-phase pump for pressurization and transfer. On the other hand, the application of a multiphase pump can provide such advantages as simplification of the equipment structure and cost savings, because there is no need for a phase separation process. Therefore, the crude oil transfer method using a multiphase pump is being applied to recently developed oil wells. Due to this increase in demand, technical demands for the development of multiphase pumps are sharply increasing, but the progress of research into related technologies is insufficient, due to the nature of multiphase pumps that require high levels of skills. This study was conducted to verify the reliability of pump performance evaluation using numerical analysis, which is the basis of the development of a multiphase pump. For this study, a model was designed by selecting the specifications of the pump under study. The performance of the designed model was evaluated through numerical analysis and experiment, and the results of the performance evaluation were compared to verify the reliability of the result using numerical analysis.

Keywords: multiphase pump, numerical analysis, experiment, performance evaluation, reliability verification

Procedia PDF Downloads 434

Authors: Ki Hyun Park, Hye Min Park, Jeong Ho Kim, Chan Jong Park, Koan Sik Joo

Abstract:

In the modern days, the use of radioactive substances is on the rise in the areas like chemical weaponry, industrial usage, and power plants. Although there are various technologies available to detect and monitor radioactive substances in the air, the technologies to detect underwater radioactive substances are scarce. In this study, computer simulation of the underwater detection system measuring beta-ray, a radioactive substance, has been done through MCNP. CaF₂, YAP(Ce) and YAG(Ce) have been used in the computer simulation to detect beta-ray as scintillator. Also, the source used in the computer simulation is Sr-90 and Y-90, both of them emitting only pure beta-ray. The distance between the source and the detector was shifted from 1mm to 10mm by 1 mm in the computer simulation. The result indicated that Sr-90 was impossible to measure below 1 mm since its emission energy is low while Y-90 was able to be measured up to 10mm underwater. In addition, the detector designed with CaF₂ had the highest efficiency among 3 scintillators used in the computer simulation. Since it was possible to verify the detectable range and the detection efficiency according to modeling through MCNP simulation, it is expected that such result will reduce the time and cost in building the actual beta-ray detector and evaluating its performances, thereby contributing the research and development.

Keywords: Beta-ray, CaF₂, detector, MCNP simulation, scintillator

Procedia PDF Downloads 510

Authors: So-Ra Jeon, Chan Byon

Abstract:

This study investigates the heat transfer characteristics of aluminum foam heat sink and pin fin heat sink subjected to an impinging air jet under a fixed pumping power condition as well as fixed flow rate condition. The effects of dimensionless pumping power or the Reynolds number and the impinging distance ratio on the Nusselt number are considered. The result shows that the effect of the impinging distance on the Nusselt number is negligible under a fixed pumping power condition, while the Nusselt number increases with decreasing the impinging distance under a fixed pumping power condition. A correlation for the pressure drop is obtained as a function of the flow rate and the impinging distance ratio. And correlations for the stagnation Nusselt number of the impinging jet are developed as a function of the pumping power. The aluminum foam heat sinks did not show higher thermal performance compared to a conventional pin fin heat sink under a fixed pumping power condition.

Keywords: aluminum foam, heat sinks, impinging jet, pumping power

Procedia PDF Downloads 305

Authors: Wing Cheuk Chan

Abstract:

It is well-known that Heidegger was highly critical of Sartre’s existential philosophy. In his famous “Letter on Humanism,” Heidegger not only draw a clear cutline between his thinking of Being and Sartre’s existentialism but also introduced a kind of anti-humanism. Such a hostile attitude towards Sartre’sExistentialism as Humanism seems to have created an unbridgeable gap between these them. Indeed, already in his Being and Nothingness, Sartre complained: Heidegger “has completely avoided any appeal to consciousness in his description of Dasein.”In reality, Sartre was mainly faithful to Husserlianphenomenology, in spite of his rejection of Husserl’s idealism. Thanks to the Japanese Buddhist scholar Yoshifumi Ueda’s work on the Old School of Yogācāra Buddhismas represented by Sthiramati and Paramārtha, we learn that in additional to thethesis of transforming vijñāna (knowing consciousness) into jñāna (wisdom), there is an idea of pṛṣṭa-labdha-jñāna (the subsequently acquired wisdom). According to Ueda, the latter is a “non-discriminative discrimination.” This gives rise to a possibility of synthesizing Heidegger’s thinking of Being and Sartre’s existential phenomenology. Structurally, this paper will firstshow that Heidegger focuses on the side of non-discrimination, whereas Sartre concentrates on the side of discrimination. It will then clarify in what sense thateach of them, in itself, remains incomplete. Finally, it will demonstratehow to synthesize them in term of the notion of “non-discriminative discrimination.”

Keywords: heidegger, sartre, phenomenology, yogācāra buddhism

Procedia PDF Downloads 105

Authors: Aklilu Alemu, Tak Cheung Chan

Abstract:

Following the intensification of secondary education in the developing world, the attention of Ethiopia has currently shifted to its quality education and its management. This study is aimed to explore experts’ perceptions of quality management challenges in secondary education in Ethiopia. The researchers employed a case study design recruiting participating supervisors from the Ministry of Education, region, zone, wereda, and cluster by using a purposeful sampling technique. Twenty-six interviewees took part in this study. The researchers employed NVivo 8 versions together with a thematic analysis process to analyze the data. This study revealed that major problems that affected quality management practices in Ethiopia were: lack of qualified experts at all levels; lack of accountability in every echelon; the changing nature of teacher education; the ineffectiveness of teacher-licensing programs; and lack of educational budget and the problem of utilizing this limited budget. The study concluded that the experts at different levels were not genuinely fulfilling their roles and responsibilities. Therefore, the Ministry of Finance and Economic Development, together with the concerned parties, needs to reconsider budget allocation for secondary education.

Keywords: education quality, Ethiopia, quality challenge, quality management, secondary education

Procedia PDF Downloads 216

Authors: Seyedeh Mozhgan Seyed-Talebi, Weng-Kent Chan, Hsin-Yi Tiffany Chen

Abstract:

Lead-free perovskite photovoltaic (PV) technology employing non-toxic tin halide perovskite absorbers is pivotal for advancing perovskite solar cell (PSC) commercialization. Despite challenges posed by perovskite sensitivity to oxygen and humidity, our study utilizes DFT calculations using VASP and NanoDCAL software and SCAPS-1D simulations to elucidate the charge transport mechanism at the interface of CsSnI₃-FASnI₃ heterojunction. Results reveal how inherent electric fields facilitate efficient carrier transport, reducing recombination losses. We predict optimized power conversion efficiencies (PCEs) and highlight the potential of CsSnI3-FASnI3 heterojunctions for cost-effective and efficient charge transport layer-free (CTLF) photovoltaic devices. Our study provides insights into the future direction of recognizing more efficient, nontoxic heterojunction perovskite devices.

Keywords: charge transport layer free, CsSnI₃-FASnI₃ heterojunction, lead-free perovskite solar cell, tin halide perovskite., Charge transport layer free

Procedia PDF Downloads 45

Authors: Chan Ka Lok Sobel

Abstract:

The rapid evolution of digital media platforms has given rise to new forms of narrative engagement, particularly through multi-channel storytelling. This research focuses on exploring the teaching pedagogy and effectiveness of multi-channel storytelling for social media, cinema, games, and streaming platforms. The study employs case studies of the popular series "Squid Game" to investigate the diverse pedagogical approaches and strategies used in teaching multi-channel storytelling. Through qualitative research methods, including interviews, surveys, and content analysis, the research assesses the effectiveness of these approaches in terms of student engagement, knowledge acquisition, critical thinking skills, and the development of digital literacy. The findings contribute to understanding best practices for incorporating multi-channel storytelling into educational contexts and enhancing learning outcomes in the digital media landscape.

Keywords: digital literacy, game-based learning, artificial intelligence, animation production, educational technology

Procedia PDF Downloads 114

Authors: José Davi Oliveira De Moura, Chou Sin Chan

Abstract:

In this study, the effect of convective momentum transport (CMT) on the life of cyclone systems and their organization is analyzed. A case of strong precipitation, in the southeast of Brazil, was simulated using Eta model with two kinds of convective parameterization: Kain-Fritsch without CMT and Kain-fritsch with CMT. Reanalysis data from CFSR were used to compare Eta model simulations. The Wind, mean sea level pressure, rain and temperature are included in analysis. The rain was evaluated by Equitable Threat Score (ETS) and Bias Index; the simulations were compared among themselves to detect the influence of CMT displacement on the systems. The result shows that CMT process decreases the intensity of meso cyclones (higher pressure values on nuclei) and change the positions and production of rain. The decrease of intensity in meso cyclones should be caused by the dissolution of momentum from lower levels from up levels. The rain production and rain distribution were altered because the displacement of the larger systems scales was changed. In addition, the inclusion of CMT process is very important to improve the simulation of life time of meteorological systems.

Keywords: convection, Kain-Fritsch, momentum, parameterization

Procedia PDF Downloads 325

Authors: Dana Lee, Young Chan Kim

Abstract:

The purpose of this paper is to examine the relationship between the fashion corporate social responsibility (CSR) ad framing and consumer purchase behaviours with the focus on consumer’s concern and involvement towards fashion brands. A self-completion questionnaire was administered to 200 respondents. Factor analysis and other statistical analyses were applied to test hypotheses. The results suggested that the quality of the product was the most important factor when consumers purchase fashion brand products with high level of responsibility towards unethical practices but surprisingly favourability for fast fashion. Unexpectedly, it was shown that consumers took the plenty of blame, but not much responsibility on buying fast fashion evading their responsibility to CSR ad, and their purchase intentions remained unchanged. The result, on the other hand, showed that fashion CSR ads can significantly moderate individuals’ emotions even though this had no significant correlation with the purchase intentions. Despite the limited sample size and geographical region, this research has important implications for contemporary fashion brands that use ad framing to understand how consumers’ involvement and concernedness toward the CSR actions in ad, influence their favourability (purchase intention) for fashion brands.

Keywords: framing effect, CSR advertisements, consumer behaviour, purchase intention

Procedia PDF Downloads 210

Authors: Nadali Babaeian Jelodar, Chan Lai Keng, Arvind Bhatt, Laleh Bordbar, Leow E Shuen, Kamaruzaman Mohamed

Abstract:

Recently artemisinin (the endoperoxide sesquiterpene lactone) has received considerable attention because of its antimalarial activity. It is isolated from the aerial part of the Artemisia annua L. Artemisinin is very difficult to synthesise also its production by mean of cell, tissue or organ cultures is very low. Presently, only its extraction from A. annua L. plants remains the only source of the drug. The reported yield of artemisinin from leaves of A. annua L. is very low and unstable, with yields typically less than 1% of leaf dry weight. To increase the percentage of artemisinin, researchers have been engaged in developing new varieties. A review concerning the breeding of A. annua L. is presented. The aim of this review is to bring together most of the available scientific research papers about the breeding conducted on the genus A. annua L., which is currently scattered across various publications. Through this review the authors hope to attract the attention of breeders throughout the world to focus on the unexplored potential of A. annua L. species. Also the future scope of this plant has been emphasized with a view of the importance of breeding of A. annua L. for increasing of artemisinin content. By releasing of new cultivar of A. annua L. and cultivation of this plant offers the opportunity to optimize yield and achieve a uniform, high quality product.

Keywords: Artemisia annua L., breeding, artemisinin, cultivation, medicinal plant

Procedia PDF Downloads 263

Authors: Minsun Kim, Ki-Sun Choi, Hyun-Jee Lee, Young-Chan You

Abstract:

There is no reinforcement example for the renovation of the vertical and horizontal extension to existing building structures which is a shear wall type in apartment units in Korea. Among these existing structures, the structures which are shear wall type are rare overseas, while Korea has many shear wall apartment units. Recently, in Korea, a few researchers are trying to confirm the possibility of the vertical extension in existing building with shear walls. This study evaluates the possibility of the renovation by applying performance-based seismic design to existing buildings with shear walls in the analysis phase of the structure. In addition, force-based seismic design, used by general structural engineers in Korea, is carried out to compare the amount of reinforcement of walls, which is a main component of wall structure. As a result, we suggest that performance-based design obtains more economical advantages than force-based seismic design.

Keywords: design for extension, performance-based design, remodeling, shear wall frame, structural analysis

Procedia PDF Downloads 225

Authors: Chan Kwon Park, Chae-Bogk Kim, Sung-Min Park

Abstract:

This study is a research on the authenticity of transactions between corporations and quality of their relationships and transaction performances. As the factors of authenticity of transactions, honesty, transparency, customer orientation and consistency were selected; as the factors of quality of relationships, trust and commitment were selected, and as the factors of transactions performances, intention of repeat transactions and switching intention were selected, and on these relationships a hypothesis was established, and verification was conducted. First, the factors of the authenticity of transactions positively influenced the factors of quality of relationships. Thus, a higher level of authenticity of transactions can lead to higher level of trust and commitment. Second, the factors of quality of relationships made a positive influence on the intention of repeat transactions, while a negative influence in the switching intention. Third, it showed that trust and commitment as the factors of quality of relationships functioned partly as the parameter between the authenticity of transactions and transaction performances. Finally, it proved that the factors of the authenticity of transactions improved trust and commitment in transactions between corporations and further improved the intention of repeat transactions while they decreased the switching intention.

Keywords: authenticity of transactions, trust, commitment, intention of repeat transactions, switching intention

Procedia PDF Downloads 373

Authors: Md. Maksudur Rahman Khan, Chee Wai Woon, Huei Ruey Ong, Vignes Rasiah, Chin Kui Cheng, Kar Min Chan, E. Baranitharan

Abstract:

The present work represents a preparation of non-precious iron-based electrocatalyst (FeN) for ORR in air-cathode microbial fuel cell by pyrolysis treatment. Iron oxalate which recovered from the industrial wastewater and Phenanthroline (Phen) were used as the iron and nitrogen precursors, respectively in preparing FeN catalyst. The performance of as prepared catalyst (FeN) was investigated in a single chambered air cathode MFC in which anaerobic sludge was used as inoculum and palm oil mill effluent as substrate. The maximum open circuit potential (OCV) and the highest power density recorded were 0.543 V and 4.9 mW/m2, respectively. Physical characterization of FeN was elucidated by using Brunauner Emmett Teller (BET), X-Ray Diffraction (XRD) analysis and Field Emission Scanning Electron Microscopy (FESEM) while the electrochemical properties were characterized by cyclic voltammetry (CV) analysis. The presence of biofilm on anode surface was examined using FESEM and confirmed using Infrared Spectroscopy and Thermogravimetric Analysis. The findings of this study demonstrated that FeN is electrochemically active and further modification is needed to increase the ORR catalytic activity.

Keywords: iron based catalyst, microbial fuel cells, oxygen reduction reaction, palm oil mill effluent

Procedia PDF Downloads 334

Authors: Paola Pannuzzo, Tak-Ming Chan

Abstract:

In seismic applications, hollow steel sections show, beyond undeniable esthetical appeal, promising structural advantages since, unlike open section counterparts, they are not susceptible to weak-axis and lateral-torsional buckling. In particular, hot-finished hollow steel sections have homogeneous material properties and favorable ductility but have been underutilized for cyclic bending. The main reason is that the parameters affecting their hysteretic behaviors are not yet well understood and, consequently, are not well exploited in existing codes of practice. Therefore, experimental investigations have been conducted on a wide range of hot-finished rectangular hollow section beams with the aim to providing basic knowledge for evaluating their seismic performance. The section geometry (width-to-thickness and depth-to-thickness ratios) and the type of loading (monotonic and cyclic) have been chosen as the key parameters to investigate the cyclic effect on the rotational capacity and to highlight the differences between monotonic and cyclic load conditions. The test results provide information on the parameters that affect the cyclic performance of hot-finished hollow steel beams and can be used to assess the design provisions stipulated in the current seismic codes of practice.

Keywords: bending, cyclic test, finite element modeling, hollow sections, hot-finished sections

Procedia PDF Downloads 155

Authors: Andrey A. Chernousov, Ben Y. B. Chan

Abstract:

The use of the low-cost paraffinic phase change material can be rather effective in smart building envelopes in the South China region. Particular attention has to be paid to the PCM optimization as an exploitation conditions and the envelope insulation changes its thermal characteristics. The studied smart building envelope consists of a reinforced aluminum exterior, polymeric insulation foam, phase change material and reinforced interior gypsum board. A prototype sample was tested to validate the numerical scheme using EnergryPlus software. Three scenarios of insulation thermal resistance loss (ΔR/R = 0%, 25%, 50%) were compared with the different PCM thicknesses (tP=0, 1, 2.5, 5 mm). The comparisons were carried out for a west facing enveloped office building (50 storey). PCM optimization was applied to find the maximum efficiency for the different ΔR/R cases. It was found, during the optimization, that the PCM is an important smart component, lowering the peak energy demand up to 2.7 times. The results are not influenced by the insulation aging in terms of ΔR/R during long-term exploitation. In hot and humid climates like Hong Kong, the insulation core of the smart systems is recommended to be laminated completely. This can be very helpful in achieving an acceptable payback period.

Keywords: smart building envelope, thermal performance, phase change material, energy efficiency, large-scale sandwich panel

Procedia PDF Downloads 730

Authors: Niya Chen, Jennifer Chan

Abstract:

In the financial market, risk management helps to minimize potential loss and maximize profit. There are two ways to assess risks; the first way is to calculate the risk directly based on the volatility. The most common risk measurements are Value at Risk (VaR), sharp ratio, and beta. Alternatively, we could look at the quantile of the return to assess the risk. Popular return models such as GARCH and stochastic volatility (SV) focus on modeling the mean of the return distribution via capturing the volatility dynamics; however, the quantile/expectile method will give us an idea of the distribution with the extreme return value. It will allow us to forecast VaR using return which is direct information. The advantage of using these non-parametric methods is that it is not bounded by the distribution assumptions from the parametric method. But the difference between them is that expectile uses a second-order loss function while quantile regression uses a first-order loss function. We consider several quantile functions, different volatility measures, and estimates from some volatility models. To estimate the expectile of the model, we use Realized Conditional Autoregressive Expectile (CARE) model with the bayesian method to achieve this. We would like to see if our proposed models outperform existing models in cryptocurrency, and we will test it by using Bitcoin mainly as well as Ethereum.

Keywords: expectile, CARE Model, CARR Model, quantile, cryptocurrency, Value at Risk

Procedia PDF Downloads 110

Authors: Ying Qi Chan, Chunyu Li, Xu Rou Yoyo Ma, Yaya Li, Saber Khederzadeh

Abstract:

In the ever-evolving landscape of genome extraction protocols, the existing methodologies grapple with issues ranging from sub-optimal yields and compromised quality to time-intensive procedures and reliance on hazardous reagents, often necessitating substantial tissue quantities. This predicament is particularly challenging for scientists in developing countries, where resources are limited. Our investigation presents a protocol for the efficient extraction of high-yield RNA from various tissues such as muscle, insect, and plant samples. Noteworthy for its advantages, our protocol stands out as the safest, swiftest (completed in just 38 minutes), most cost-effective (coming in at a mere US$0.017), and highly efficient method in comparison to existing protocols. Notably, our method avoids the use of hazardous or toxic chemicals such as chloroform and phenol and enzymatic agents like RNase and Proteinase K. Our RNA extraction protocol has demonstrated clear advantages over other methods, including commercial kits, in terms of yield. This nucleic acid extraction protocol is more environmentally and research-friendly, suitable for a range of tissues, even in tiny volumes, hence facilitating various genetic diagnosis and researches across the globe.

Keywords: RNA extraction, rapid protocol, universal method, diverse tissues

Procedia PDF Downloads 74

Authors: Chih-Wei Cheng, Wei-Jen Chan, Yu-Han Huang, Yi-Tsung Lin, Yen-Wei Huang, Min-Cheng Chen, Shou-Zen Chang, G. Chern, Yuan-Chieh Tseng

Abstract:

How to develop spin-orbit-torque (SOT) devices with the virtues of field-free, perpendicular magnetic anisotropy (PMA), and low switching current is one of the many challenges in spintronics today. We propose a CoFeB/Ta/CoFeB tri-layer antiferromagnetic SOT device that could meet the above requirements. The device’s PMA was developed by adopting CoFeB–MgO interface. The key to the success of this structure is to ensure that (i)changes of the inter-layer coupling(IEC) and CoFeB anisotropy can occur simultaneously; (ii) one of the CoFeB needs to have a slightly tilted moment in the beginning. When sufficient current is given, the SHEreverses the already-tiltedCoFeB, and the other CoFeB can be reversed simultaneously by the IEC with the field-free nature. Adjusting the thickness of Ta can modify the coupling state to reduce the switching current while the field-free nature was preserved. Micromagnetic simulation suggests that the Néel orange peel effect (NOPE) is non-negligible due to interface roughness and coupling effect in the presence of perpendicular anisotropy. Fortunately, the Néel field induced by the NOPE appears to favor the field-free reversal.

Keywords: CoFeB, spin-orbit torque, antiferromagnetic, MRAM, trilayer

Procedia PDF Downloads 117

Authors: Mark Darius Juszczak

Abstract:

While epistemology, as a sub-field of philosophy, is generally concerned with theoretical questions about the nature of knowledge, the explosion in digital media technologies has resulted in an exponential increase in the storage and transmission of human information. That increase has resulted in a particular non-linear dynamic – digital epistemological functions are radically altering how and what we know. Neither the rate of that change nor the consequences of it have been well studied or taken into account in developing state-level strategies for epistemological functions. At the current time, US Federal policy, like that of virtually all other countries, maintains, at the national state level, clearly defined boundaries between various epistemological agencies - agencies that, in one way or another, mediate the functional use of knowledge. These agencies can take the form of patent and trademark offices, national library and archive systems, departments of education, departments such as the FTC, university systems and regulations, military research systems such as DARPA, federal scientific research agencies, medical and pharmaceutical accreditation agencies, federal funding for scientific research and legislative committees and subcommittees that attempt to alter the laws that govern epistemological functions. All of these agencies are in the constant process of creating, analyzing, and regulating knowledge. Those processes are, at the most general level, epistemological functions – they act upon and define what knowledge is. At the same time, however, there are no high-level strategic epistemological directives or frameworks that define those functions. The only time in US history where a proxy state-level epistemological strategy existed was between 1961 and 1969 when the Kennedy Administration committed the United States to the Apollo program. While that program had a singular technical objective as its outcome, that objective was so technologically advanced for its day and so complex so that it required a massive redirection of state-level epistemological functions – in essence, a broad and diverse set of state-level agencies suddenly found themselves working together towards a common epistemological goal. This paper does not call for a repeat of the Apollo program. Rather, its purpose is to investigate the minimum structural requirements for a national state-level epistemological strategy in the United States. In addition, this paper also seeks to analyze how the epistemological work of the multitude of national agencies within the United States would be affected by such a high-level framework. This paper is an exploratory study of this type of framework. The primary hypothesis of the author is that such a function is possible but would require extensive re-framing and reclassification of traditional epistemological functions at the respective agency level. In much the same way that, for example, DHS (Department of Homeland Security) evolved to respond to a new type of security threat in the world for the United States, it is theorized that a lack of coordination and alignment in epistemological functions will equally result in a strategic threat to the United States.

Keywords: strategic security, epistemological functions, epistemological agencies, Apollo program

Procedia PDF Downloads 77

Authors: Kuang-Hsiung Tan, Chih-Chan Hu, Chien-Wu Lan, Shih-Sung Lin, Te-Jen Chang

Abstract:

An active islanding detection method using disturbance signal injection with intelligent controller is proposed in this study. First, a DC\AC power inverter is emulated in the distributed generator (DG) system to implement the tracking control of active power, reactive power outputs and the islanding detection. The proposed active islanding detection method is based on injecting a disturbance signal into the power inverter system through the d-axis current which leads to a frequency deviation at the terminal of the RLC load when the utility power is disconnected. Moreover, in order to improve the transient and steady-state responses of the active power and reactive power outputs of the power inverter, and to further improve the performance of the islanding detection method, two probabilistic fuzzy neural networks (PFNN) are adopted to replace the traditional proportional-integral (PI) controllers for the tracking control and the islanding detection. Furthermore, the network structure and the online learning algorithm of the PFNN are introduced in detail. Finally, the feasibility and effectiveness of the tracking control and the proposed active islanding detection method are verified with experimental results.

Keywords: distributed generators, probabilistic fuzzy neural network, islanding detection, non-detection zone

Procedia PDF Downloads 389

Authors: S. S. Dol, M. S. Chan, S. F. Wong, J. S. Lim

Abstract:

Emulsion formation is unavoidable and can be detrimental to an oil field production. The presence of stable emulsions also reduces the quality of crude oil and causes more problems in the downstream refinery operations, such as corrosion and pipeline pressure drop. Hence, it is important to know the effects of emulsions in the pipeline. Light crude oil was used for the continuous phase in the W/O emulsions where the emulsions pass through a flow loop to test the pressure drop across the pipeline. The results obtained shows that pressure drop increases as water cut is increased until it peaks at the phase inversion of the W/O emulsion between 30% to 40% water cut. Emulsions produced by gradual constrictions show a lower stability as compared to sudden constrictions. Lower stability of emulsions in gradual constriction has the higher influence of pressure drop compared to a sudden sharp decrease in diameter in sudden constriction. Generally, sudden constriction experiences pressure drop of 0.013% to 0.067% higher than gradual constriction of the same ratio. Lower constriction ratio cases cause larger pressure drop ranging from 0.061% to 0.241%. Considering the higher profitability in lower emulsion stability and lower pressure drop at the developed flow region of different constrictions, an optimum design of constriction is found to be gradual constriction with a ratio of 0.5.

Keywords: constriction, pressure drop, turbulence, water-in-oil emulsions

Procedia PDF Downloads 335

Authors: Kevin Chan, Kevin K. H. Chung, Patcy P. S. Yeung, H. L. Ip, Bill T. C. Chung, Karen M. K. Chung

Abstract:

Purpose: Recent evidence shows that reading self-efficacy and students perceived difficulty in reading are significantly associated with word reading and reading fluency. However, little is known about these relationships among students learning to read English as a second language, particularly in Chinese students. This study examined the contributions of reading self-efficacy, perception of difficulty in reading, and cognitive-linguistic skills to performance on English word reading and reading fluency in Chinese students. Method: A sample of 122 second-and third-grade students in Hong Kong, China, participated in this study. Students completed the measures of reading self-efficacy and perception of difficulty in reading. They were assessed on their English cognitive-linguistic and reading skills: rapid automatized naming, nonword reading, phonological awareness, word reading, and one-minute word reading. Results: Results of path analysis indicated that when students’ grades were controlled, reading self-efficacy was a significant correlate of word reading and reading fluency, whereas perception of difficulty in reading negatively predicted word reading. Conclusion: These findings underscore the importance of taking students’ reading self-efficacy and perception of difficulty in reading and their cognitive-linguistic skills into consideration when designing reading intervention and instructions for students learning English as a second language.

Keywords: self-efficacy, perception of difficulty in reading, english as a second language, word reading

Procedia PDF Downloads 189

Authors: Park Sung-Min, Chan Kwon Park, Kim Chae-Bogk

Abstract:

This study aims to analyze the relationship between nonverbal communication, perceived expertise, service quality, and trust. The study was conducted with clients using cosmetic stores in the Daegu area of Korea. Based on the prior study, the measurement questions are correctly amended and organized in this study. The exploration factor analysis was performed using SPSS 22 for the configured measurement questions. And PLS 2.0 was used to perform a confirmatory factor analysis and path analysis. As a result of the analysis, nonverbal communication has been categorized as physical appearance, kinesics, vocal behavior and proxemics. It has been shown that all of the factors in nonverbal communication have a (+) significant effect on perceived expertise. The degree of impact has been analyzed to influence the perceived expertise in the order in which physical appearance, vocal behavior, kinesics and proxemics. The perceived expertise was analyzed to have a (+) significant effect on the service quality. It has been shown that the service quality has a (+) significant effect on trust.

Keywords: nonverbal communication, perceived expertise, service quality, trust

Procedia PDF Downloads 284

Authors: Sung-Min Park, Chan Kwon Park, Chae-Bogk Kim

Abstract:

The purpose of this study is to analyze the relationship between transaction fairness, social capital, supply chain integration and sustainability. Based on the previous studies, measurement items were determined by using SPSS 22 and exploratory factor analysis was performed, and again, using AMOS 21 for confirmatory factor analysis and path analysis was performed by using study items that satisfy reliability, validity, and appropriateness of measurement model. It has shown that transaction fairness has a (+) significant effect on social capital, social capital on supply chain integration, supply chain integration on economic sustainability and social sustainability, and has a (+), but not significant effect on environmental sustainability. It has shown that supply chain integration has been proven to play a role as a parameter between social capital and economic and social sustainability, but not as a parameter between environmental sustainability. Through this study, it is suggested that clearly examining the relationship between fairness of trade, social capital, supply chain integration and sustainability, maintaining fairness of the transaction make formation of social capital, and further integration of supply chain, and achieve sustainability of entire supply chain.

Keywords: transaction fairness, social capital, supply chain integration, sustainability

Procedia PDF Downloads 441

Authors: Hee-Jae Suh, Kyung-Su Kim, Min-Ji Kim, Yeon-Seong Jeong, Ok-Hwan Lee, Jae-Wook Shin, Hyang-Sook Chun, Chan Lee

Abstract:

Canthaxanthin is keto-carotenoid produced from beta-carotene and it has been approved to be used in many countries as a food coloring agent. Canthaxanthin has been analyzed using High Performance Liquid Chromatography (HPLC) system with various ways of pretreatment methods. Four official methods for verification of canthaxanthin at FSA (UK), AOAC (US), EFSA (EU) and MHLW (Japan) were compared to improve its analytical and the pretreatment method. The Linearity, the limit of detection (LOD), the limit of quantification (LOQ), the accuracy, the precision and the recovery ratio were determined from each method with modification in pretreatment method. All HPLC methods exhibited correlation coefficients of calibration curves for canthaxanthin as 0.9999. The analysis methods from FSA, AOAC, and MLHW showed the LOD of 0.395 ppm, 0.105 ppm, and 0.084 ppm, and the LOQ of 1.196 ppm, 0.318 ppm, 0.254 ppm, respectively. Among tested methods, HPLC method of MHLW with modification in pretreatments was finally selected for the analysis of canthaxanthin in lab, because it exhibited the resolution factor of 4.0 and the selectivity of 1.30. This analysis method showed a correlation coefficients value of 0.9999 and the lowest LOD and LOQ. Furthermore, the precision ratio was lower than 1 and the accuracy was almost 100%. The method presented the recovery ratio of 90-110% with modification in pretreatment method. The cross-validation of coefficient variation was 5 or less among tested three institutions in Korea.

Keywords: analytic method, canthaxanthin, food colorants, pretreatment method

Procedia PDF Downloads 683

Authors: Ka Yan Chan

Abstract:

Cohabitation among couples has been increasingly common in recent decades. Nonetheless, insufficient attention was given to the impact of attachment on cohabitation. This study discussed the experience of cohabitation among women with insecure attachments by collecting qualitative data through semi-structured interviews. Through thematic analysis, the study explored the characteristics of the women, the formation of cohabitation, struggles, coping mechanisms, and the impacts of cohabitation on the women. Moreover, the influences of the family-of-origin on cohabitation and the needs of the women were explored. The findings indicated that insecure attachment and the family-of-origin had significant effects on cohabitation and the interaction among the cohabitating couples. Women with insecure attachments were more likely to enter cohabitation unconsciously and without discussing what cohabitation means for their relationship with their partners. The findings also suggested that committing to marriage was not the only method for the women to feel secure in the relationship. Instead, long-lasting love and care, as well as reliability from their partners, could satisfy their emotional needs. More importantly, the findings revealed that repairing attachment problems and dealing with challenges in life stage transition is associated with positive impacts on the cohabitation experience. Additionally, to meet the needs of diverse family structures and to provide all-rounded support for enhancing the wellbeing of individuals, cohabitants, and couples, a comprehensive intervention model of relationship enrichment was discussed.

Keywords: cohabitation, family-of-origin, insecure attachment, relationship enrichment

Procedia PDF Downloads 82