Search results for: adhesive bridge

Authors: Henar Martín-Sanz García, Eleni Chatzi, Eugen Brühwiler

Abstract:

Located on the shore of Geneva Lake, in Switzerland, the Chillon Viaducts are two parallel structures consisted of post-tensioned concrete box girders, with a total length of 2 kilometers and 100m spans. Built in 1969, the bridges currently accommodate a traffic load of 50.000 vehicles per day, thereby holding a key role both in terms of historic value as well as socio-economic significance. Although several improvements have been carried out in the past two decades, recent inspections demonstrate an Alkali-Aggregate reaction in the concrete deck and piers reducing the concrete strength. In order to prevent further expansion of this issue, a layer of 40 mm of Ultra High Performance Fiber Reinforced cement-based Composite (UHPFRC) (incorporating rebars) was casted over the slabs, acting as a waterproof membrane and providing significant increase in resistance of the bridge structure by composite UHPFRC – RC composite action in particular of the deck slab. After completing the rehabilitation works, a Structural Monitoring campaign was installed on the deck slab in one representative span, based on accelerometers, strain gauges, thermal and humidity sensors. This campaign seeks to reveal information on the behavior of UHPFRC-concrete composite systems, such as increase in stiffness, fatigue strength, durability and long-term performance. Consequently, the structural monitoring is expected to last for at least three years. A first insight of the analyzed results from the initial months of measurements is presented herein, along with future improvements or necessary changes on the deployment.

Keywords: composite materials, rehabilitation, structural health monitoring, UHPFRC

Procedia PDF Downloads 279

Authors: Rose C.Anamezie, Mishack T. Gumbo

Abstract:

Physics learners’ poor retention, which culminates in poor achievement due to teaching approaches that are unrelated to learners’ in non-Western cultures, warranted the study. The tenet of this study was to determine the effectiveness of the ethnoscience-based teaching (EBT) approach on learners’ retention in the Physics concept of Optics in the Awka Education zone of Anambra State- Nigeria. Two research questions and three null hypotheses tested at a 0.05 level of significance guided the study. The design adopted for the study was Quasi-experimental. Specifically, a non-equivalent control group design was adopted. The population for the study was 4,825 SS2 Physics learners in the zone. 160 SS2 learners were sampled using purposive and random sampling. The experimental group was taught rectilinear propagation of light (RPL) using the EBT approach, while the control group was taught the same topic using the lecture method. The instrument for data collection was the 50 Physics Retention Test (PRT) which was validated by three experts and tested for reliability using Kuder-Richardson’s formula-20, which yielded coefficients of 0.81. The data were analysed using mean, standard deviation and analysis of co-variance (p< .05). The results showed higher retention for the use of the EBT approach than the lecture method, while there was no significant gender-based factor in the learners’ retention in Physics. It was recommended that the EBT approach, which bridged the gender gap in Physics retention, be adopted in secondary school teaching and learning since it could transform science teaching, enhance learners’ construction of new science concepts based on their existing knowledge and bridge the gap between Western science and learners’ worldviews.

Keywords: Ethnoscience-based teaching, optics, rectilinear propagation of light, retention

Procedia PDF Downloads 82

Authors: Nisar Alungal Chungath

Abstract:

“No human being is illegal" has become a dictum strongly upheld in the context of global immigration and migration, highlighting the ethical and moral dimensions of how societies and governments treat individuals and communities who have crossed political borders or are living in a country without legal authorization. It seeks to shift the focus from categorizing human beings as illegal immigrants to recognizing their inherent human rights and the complexities of their circumstances. As a complex social phenomenon, law has been a crucial instrument in shaping, regulating and governing human societies and vice versa. The law has now become a humongous political project of the modern majoritarian regimes to democratically illegitimize and illegalize the unpopular sections and minorities. Drawing from the theoretical frameworks of dialectics, the paper explores the philosophical underpinnings of the historical evolution and dynamic nature of modern law. The paper employs a phenomenological approach to analyze the dialectical relations between individuals, societies, and legal systems, aiming to shed light on the ethical and political implications of these interactions. By examining the historical essence of law, its relationship with social and cultural norms, and the role of power dynamics, this article argues for constantly maintaining the dialectics of law—the dynamic interplay between legal norms, social practices, cultural values, and historical contexts through a philosophical and phenomenological lens, in order to bridge the gap between universal principles and particular contexts. The paper will shed light to the dialectics of the law in the context of instances of the legal persecutions of the modern secular democracies such as Citizenship Amendment Act-2019, India.

Keywords: phenomenology, dialectic, modern law, politics, resistance, margins

Procedia PDF Downloads 56

Authors: Norshaffika I. Zaiedy Nor, Andrew P. Smith

Abstract:

Background: Training is essential to develop individuals’ expertise to meet current and future job demands and to improve work performance. At the same time, individuals’ well-being is crucial to ensure that they can fully and positively carry out their daily duties. In addition to the studies that have examined what constitutes well-being and the factors behind it, many researchers have investigated the predictors of training effectiveness and transfer of training. However, there has been very little integration between them. This study was an attempt to bridge the gap between training effectiveness predictors and well-being. Purpose: This research paper aimed to investigate the association between well-being among employees and psychosocial characteristics, together with training variables. Training variables consist of motivation to learn; learning; implementation intention; and cognitive dissonance. Methodology: In total, 210 workers who had undergone various training programs completed an online survey measuring various psychosocial characteristics, four training variables, and level of well-being. Findings: The results showed that certain types of positive psychosocial characteristics (e.g., positive personality, positive work behaviors, positive work and resources) predict motivation to learn, learning and implementation intention. Meanwhile, negative psychosocial characteristics (e.g. negative work demands and resources, negative coping) predict cognitive dissonance. Also, all the training variables had a moderate to high correlation with well-being. However, after controlling other variables (age, gender, education and psychosocial characteristics), none of the training variables predicted well-being. Self-determination theory, cognitive dissonance theory, and the DRIVE model were used to explain these findings. Conclusion: As there is limited research on the integration of training variables with well-being, this study gives a new perspective in the field of both training and well-being. Further investigations are needed to examine the relationships between them.

Keywords: cognitive dissonance, implementation intention, learning, motivation to learn, psychosocial characteristics, well-being

Procedia PDF Downloads 215

Authors: Zain Ul Hassan, Muhammad Zain Ul Abadin, Muhammad Zubair Khan

Abstract:

Unmanned aerial vehicles (UAVs) have now become of predominant importance for various operations, and an immense amount of work is going on in this specific category. The structural stability and life of these UAVs is key factor that should be considered while deploying them to different intelligent operations as their failure leads to loss of sensitive real-time data and cost. This paper presents an applied research on the development of a structural health monitoring system for a UAV designed and fabricated by deploying modular approach. Firstly, a modular UAV has been designed which allows to dismantle and to reassemble the components of the UAV without effecting the whole assembly of UAV. This novel approach makes the vehicle very sustainable and decreases its maintenance cost to a significant value by making possible to replace only the part leading to failure. Then the SHM for the designed architecture of the UAV had been specified as a combination of wings integrated with strain gauges, on-board data logger, bridge circuitry and the ground station. For the research purpose sensors have only been attached to the wings being the most load bearing part and as per analysis was done on ANSYS. On the basis of analysis of the load time spectrum obtained by the data logger during flight, fatigue life of the respective component has been predicted using fracture mechanics techniques of Rain Flow Method and Miner’s Rule. Thus allowing us to monitor the health of a specified component time to time aiding to avoid any failure.

Keywords: fracture mechanics, rain flow method, structural health monitoring system, unmanned aerial vehicle

Procedia PDF Downloads 294

Authors: Agnieszka Markowska-Radomska, Ewa Dluska

Abstract:

Maintaining a bioactive substances dense diet is important for the elderly, especially to prevent diseases and to support healthy ageing. Adequate bioactive substances intake can reduce the risk of developing chronic diseases (e.g. cardiovascular, osteoporosis, neurodegenerative syndromes, diseases of the oral cavity, gastrointestinal (GI) disorders, diabetes, and cancer). This can be achieved by introducing a comprehensive supplementation of components necessary for the proper functioning of the ageing body. The paper proposes the multiple emulsions of the W1/O/W2 (water-in-oil-in-water) type as carriers for effective co-encapsulation and co-delivery of bioactive substances in supplementation of the elderly. Multiple emulsions are complex structured systems ("drops in drops"). The functional structure of the W1/O/W2 emulsion enables (i) incorporation of one or more bioactive components (lipophilic and hydrophilic); (ii) enhancement of stability and bioavailability of encapsulated substances; (iii) prevention of interactions between substances, as well as with the external environment, delivery to a specific location; and (iv) release in a controlled manner. The multiple emulsions were prepared by a one-step method in the Couette-Taylor flow (CTF) contactor in a continuous manner. In general, a two-step emulsification process is used to obtain multiple emulsions. The paper contains a proposal of emulsion functionalization by introducing pH-responsive biopolymer—carboxymethylcellulose sodium salt (CMC-Na) to the external phase, which made it possible to achieve a release of components controlled by the pH of the gastrointestinal environment. The membrane phase of emulsions was soybean oil. The W1/O/W2 emulsions were evaluated for their characteristics (drops size/drop size distribution, volume packing fraction), encapsulation efficiency and stability during storage (to 30 days) at 4ºC and 25ºC. Also, the in vitro multi-substance co-release process were investigated in a simulated gastrointestinal environment (different pH and composition of release medium). Three groups of stable multiple emulsions were obtained: emulsions I with co-encapsulated vitamins B12, B6 and resveratrol; emulsions II with vitamin A and β-carotene; and emulsions III with vitamins C, E and D3. The substances were encapsulated in the appropriate emulsion phases depending on the solubility. For all emulsions, high encapsulation efficience (over 95%) and high volume packing fraction of internal droplets (0.54-0.76) were reached. In addition, due to the presence of a polymer (CMC-Na) with adhesive properties, high encapsulation stability during emulsions storage were achieved. The co-release study of encapsulated bioactive substances confirmed the possibility to modify the release profiles. It was found that the releasing process can be controlled through the composition, structure, physicochemical parameters of emulsions and pH of the release medium. The results showed that the obtained multiple emulsions might be used as potential liquid complex carriers for controlled/modified/site-specific co-delivery of bioactive substances in dietary supplementation in the elderly.

Keywords: bioactive substance co-release, co-encapsulation, elderly supplementation, multiple emulsion

Procedia PDF Downloads 198

Authors: Franklin N. Mabe, Samuel A. Donkoh, Seidu Al-Hassan

Abstract:

In order to increase and bridge the differences in rice yield, many farmers have resorted to adopting Farmer Innovation Systems (FISs) and Improved Agricultural Technologies (IATs). This study econometrically analysed the impacts of adoption of FISs and IATs on rice yield using multinomial endogenous switching regression (MESR). Nine-hundred and seven (907) rice farmers from Guinea Savannah Zone (GSZ), Forest Savannah Transition Zone (FSTZ) and Coastal Savannah Zone (CSZ) were used for the study. The study used both primary and secondary data. FBO advice, rice farming experience and distance from farming communities to input markets increase farmers’ adoption of only FISs. Factors that increase farmers’ probability of adopting only IATs are access to extension advice, credit, improved seeds and contract farming. Farmers located in CSZ have higher probability of adopting only IATs than their counterparts living in other agro-ecological zones. Age and access to input subsidy increase the probability of jointly adopting FISs and IATs. FISs and IATs have heterogeneous impact on rice yield with adoption of only IATs having the highest impact followed by joint adoption of FISs and IATs. It is important for stakeholders in rice subsector to champion the provision of improved rice seeds, the intensification of agricultural extension services and contract farming concept. Researchers should endeavour to researched into FISs.

Keywords: farmer innovation systems, improved agricultural technologies, multinomial endogenous switching regression, treatment effect

Procedia PDF Downloads 425

Authors: Aline F. C. Pereira

Abstract:

In recent years, modern slavery has increasingly gathered attention in scholarly discussions and policy debates. Whereas the mainstream studies focus on forced labour and trafficking, little attention is paid to other forms of exploitation, such as degrading conditions of work –criminalised in Brazil as an autonomous type of slavery since 2003. This paper aims to bridge this gap. It adopts a mixed method that comprises both qualitative and quantitative analysis, to investigate the adjudication of 164 cases of degrading conditions of work by Brazilian labour courts. The research discloses an ungrounded reluctance to apply the domestic legal framework, as in most of the cases degrading conditions of work are not recognised as contemporary slavery, despite the law. In some cases, not even situations described as subhuman and degrading of human dignity were framed as slavery. The analysis also suggests that, as in chattel times, lack of freedom and subjection remain relevant in the legal characterisation of slave labour. The examination has further unraveled a phenomenon absent in previous studies: normalisation of precarity. By depicting precarity as natural and inevitable in rural areas, labour courts ensure conformity to the status quo and reduce the likelihood of resistance by victims. Moreover, compensations afforded to urban workers are higher than granted to rural employees, which seems to place human beings in hierarchical categories -a trace of colonialism. In sum, the findings challenge the worldwide spread assumption that Brazil addresses slavery efficiently. Conversely, the Brazilian Labour Judiciary seems to remain subservient to a colonial perspective of slavery, legitimising, and sanctioning abusive practices.

Keywords: adjudication, contemporary slavery, degrading conditions of work, normalisation of precarity

Procedia PDF Downloads 113

Authors: Steven Arcidiacono, Robert Stote, Erin Anderson, Molly Richards

Abstract:

There are numerous standard test methods for antimicrobial textiles that measure activity against specific microorganisms. However, many times these results do not translate to the performance of treated textiles when worn by individuals. Standard test methods apply a single target organism grown under optimal conditions to a textile, then recover the organism to quantitate and determine activity; this does not reflect the actual performance environment that consists of polymicrobial communities in less than optimal conditions or interaction of the textile with the skin substrate. Here we propose the development of in vitro skin model method to bridge the gap between lab testing and wear studies. The model will consist of a defined polymicrobial community of 5-7 commensal microbes simulating the skin microbiome, seeded onto a solid tissue platform to represent the skin. The protocol would entail adding a non-commensal test organism of interest to the defined community and applying a textile sample to the solid substrate. Following incubation, the textile would be removed and the organisms recovered, which would then be quantitated to determine antimicrobial activity. Important parameters to consider include identification and assembly of the defined polymicrobial community, growth conditions to allow the establishment of a stable community, and choice of skin surrogate. This model could answer the following questions: 1) is the treated textile effective against the target organism? 2) How is the defined community affected? And 3) does the textile cause unwanted effects toward the skin simulant? The proposed model would determine activity under conditions comparable to the intended application and provide expanded knowledge relative to current test methods.

Keywords: antimicrobial textiles, defined polymicrobial community, in vitro skin model, skin microbiome

Procedia PDF Downloads 137

Authors: Hondozi Jahja

Abstract:

There is an obvious need to learn Arabic language and teach it to other speakers through the new curricula. The idea is to bridge the gap between theory and practice. To that end, we have sought to offer some means of help to master the Arabic language, in addition to our efforts to apply these means, enriching the culture of the student and develop his vocabulary. There is no doubt that taking care of the practical aspect of the grammar was our constant goal, and this particular aspect is what builds the student’s positive values and refine his taste and develop his language. In addressing these issues, we have adopted a school-based approach based primarily on the active and positive participation of the student. The theoretical linguistic issues - in our opinion - are not a primary goal, but the goal is to be used them by students through speaking and applying them. Among the objectives of this research is to establish the basic language skills of the students using new means that help the student to acquire these skills and apply them in various subjects of interest in his progress and development. Unfortunately, some of our students consider the grammar as ‘difficult’, ‘complex’ and ‘heavy’ in itself. This is one of the obstacles that stand in the way of their desired results. As a consequence, they end up talking – mumbling - about the difficulties they face in applying those rules. Therefore, some of our students finish their university studies and are unable to express what they feel using language correctly. For this purpose, we have sought in this research to follow a new integrated approach, which is to study the grammar of the language through modern means of the consolidation of the principle of functional language, and that the rule implies to control tongues and linguistic expressions properly. This research is a result of a practical experience as a teacher of Arabic language for non-native speakers at the ‘Hassan Pristina’ University, located in Pristina, the capital of Kosovo and at the Qatar Training Center since its establishment in 2012.

Keywords: arabic, applied methods, acquire, learning

Procedia PDF Downloads 158

Authors: Gopika Rajagopal, Sudheesh Thiyyakkandi

Abstract:

Back-to-back reinforced earth (RE) walls are extensively used in these days as bridge abutments and highway ramps, owing to their cost efficiency and ease of construction. High quality select fill is the most suitable backfill material due to its excellent engineering properties and constructability. However, industries are compelled to use low quality, locally available soil because of its ample availability on site. However, several failure cases of such walls are reported, especially subsequent to rainfall events. The stiffness of reinforcement is one of the major factors affecting the performance of RE walls. The present study focused on analyzing the effect of reinforcement stiffness on the performance of complete select fill, complete marginal fill, and hybrid-fill (i.e., combination of select and marginal fills) back-to-back RE walls, immediately after construction and upon rainwater infiltration through finite element modelling. A constant width to height (W/H) ratio of 3 and height (H) of 6 m was considered for the numerical analysis and the stiffness of reinforcement layers was varied from 500 kN/m to 10000 kN/m. Results showed that reinforcement stiffness had a noticeable influence on the response of RE wall, subsequent to construction as well as rainwater infiltration. Facing displacement was found to decrease and maximum reinforcement tension and factor of safety were observed to increase with increasing the stiffness of reinforcement. However, beyond a stiffness of 5000 kN/m, no significant reduction in facing displacement was observed. The behavior of fully marginal fill wall considered in this study was found to be reasonable even after rainwater infiltration when the high stiffness reinforcement layers are used.

Keywords: back-to-back reinforced earth wall, finite element modelling, rainwater infiltration, reinforcement stiffness

Procedia PDF Downloads 155

Authors: Shilpi Tripathi

Abstract:

After independence, Bangladesh had to learn to survive on its own without any economic crutches (aid). Foreign direct investment (FDI) became a crucial economic tool for the country to become economically independent. The government started removing restrictions to encourage foreign investment, economic growth, international trade, and the environment. FDI is considered as a way to bridge the saving-investment gap, reduce poverty, balance trade, create jobs for its vast labour force, increase foreign exchange earnings and acquire new modern technology and management skills in the country. At the same time, spillovers of foreign investments in Bangladesh, such as low wages (compared to laborers of developed countries), poor working conditions and unbridled exploitation of the domestic resources, environmental externalities, etc., cannot be ignored. The most important adverse implications of FDI inflows noticed are the environmental problems, which are further impacting the health and society of the country. This paper empirically studies the relationship between FDI, economic growth, international trade (exports and Imports), and the environment since 1996. The first part of the paper focuses on the background and trends of FDI, GDP, trade, and environment (CO₂). The second part focuses on the literature review on the relationship between all the variables. The last part of the paper examines the results of empirical analysis like co-integration and Granger causality. The findings of the paper reveal that a uni-directional relationship exists between FDI, CO₂, and international trade (exports and imports). The direction of the causality reveals that FDI inflow is one of the major contributors to high-volume international trade. At the same time, FDI and international trade both are contributing to carbon emissions in Bangladesh. The paper concludes with the policy recommendations that will ensure environmentally friendly trade, investment, and growth in Bangladesh for the future.

Keywords: foreign direct investment, GDP, international trade, CO₂, Granger causality, environment

Procedia PDF Downloads 181

Authors: Vicent Lwanga

Abstract:

Issue: Communication between parent and child is important and necessary. Poor parenting and lack of openness and communication between parents and their children contribute to the increasing rate of HIV infection among young persons between the ages of 10-25. The young person, when left on their own are at the risk of misinformation from peers and from other sources. Description: Parent-Child Communication (PCC) was designed as a key component of a community-based HIV and AIDS intervention focused on young persons by Elderly Widows Orphans Family Support Organisation. Findings from the preliminary community-level process indicated that the lack of parent-child communication militates against young persons adopting and maintaining healthier sexual behaviors. An integrated youth strategy consisting of youth Peer Education/Facilitation and PCC was used to bridge this gap. The process involved an interactive parent-child forum, which allowed parents and children to meet and have open and frank discussions on the needs of young persons and the role of parents. This forum addressed all emerging issues from all parties and created better cordiality amongst them. Lessons Learnt: When young people feel unconnected to their parents, family, or home, they may become involved in activities that put their health at risk. Equally, when parents affirm the value of their children through open interaction, children are more likely to develop positive and healthy attitudes about themselves. Creating the opportunity for this interactive forum is paramount in any intervention program focused on young persons. Conclusion: HIV and AIDS-related programmes, especially those focusing on youth, should have PCC as an integral, essential component. Parents should be vehicles for information dissemination and need to be equipped with the capacity and skills to take on the onerous task of talking sexual reproductive health and sexuality with their children and wards.

Keywords: aids, communication, HIV, youth

Procedia PDF Downloads 123

Authors: Adegoriola Mayowa I., Lai Joseph H. K., Yung Esther H. K., Chan Edwin H. K.

Abstract:

Heritage buildings (HBs) as structures with historical and architectural relevance that form an integral part of contemporary society. These buildings deserve to be protected for as long as possible to retain their significance. Therefore, the need to prioritize HB maintenance management is pertinent. However, the decision-making process of HBMM can be relatively daunting. The decision-making challenge may be attributed to the multiple 'stakeholders' expectation and requirement which needs to be met. To this end, professionals in the built environment have identified the need to apply the strategic concept of facilities management (FM) in decision making. Furthermore, the different maintenance dimensions have been applied to maintenance management of residential, commercial, and health facilities. Unfortunately, these different maintenance approaches, such as FM, sustainable FM, urban FM, green FM, and strategic FM, are yet to be fully explored in the decision-making process of HBMM. To bridge this gap, this study focuses on developing a framework for strategic decision-making HBMM, which helps achieve HBMM sustainability. At the study's inception, relevant works of literature in the domains of HBMM and FM were conducted. This review helped in the identification of contemporary maintenance practices and their applicability to HBMM. Afterward, a conceptual framework to aid decision-making in HBMM was developed. This framework integrated the concept of FM scope (people, place, process, and technology) while ensuring that decisions plans were made at strategic, tactical, and operational levels. Also, the different characteristics of HBs and stakeholders' requirements were considered in the framework. The conceptual framework presents a holistic guide for professionals in HBMM to ensure that decision processes and outcomes are practical and efficient. It also contributes to the existing body of knowledge on the integration of FM in HBMM. Furthermore, it will serve as a basis for future studies by applying the conceptualized framework in actual cases.

Keywords: decision-making, facility management, strategy, sustainability, heritage building, maintenance

Procedia PDF Downloads 138

Authors: Ekki Kurniawan, Yusuf Nur Jayanto, Erna Sugesti, Efri Suhartono, Agus Ganda Permana, Jaspar Hasudungan, Jangkung Raharjo, Rintis Manfaati

Abstract:

The purpose of this research is to study the current characteristic of the electrolysis of mineral water to produce hydrogen, alkaline water, and acid water. Alkaline and hydrogen water are believed to have health benefits. Alkaline water containing hydrogen can be an anti-oxidant that captures free radicals, which will increase the immune system. In Indonesia, there are two existing types of alkaline water producing equipment, but the installation is complicated, and the price is relatively expensive. The electrolysis process is slow (6-8 hours) since they are locally made using 311 VDC full bridge rectifier power supply. This paper intends to discuss how to make hydrogen and alkaline water by a simple portable mineral water ionizer. This is an electrolysis device that is easy to carry and able to separate ions of mineral water into acidic and alkaline water. With an electric field, positive ions will be attracted to the cathode, while negative ions will be attracted to the anode. The circuit equivalent can be depicted as RLC transient ciruit. The diode component ensures that the electrolytic current is direct current. Switch S divides the switching times t1, t2, and t3. In the first stage up to t1, the electrolytic current increases exponentially, as does the inductor charging current (L). The molecules in drinking water experience magnetic properties. The direction of the dipole ions, which are random in origin, will regularly flare with the direction of the electric field. In the second stage up to t2, the electrolytic current decreases exponentially, just like the charging current of a capacitor (C). In the 3rd stage, start t3 until it tends to be constant, as is the case with the current flowing through the resistor (R).

Keywords: current electrolysis, mineral water, ions, alkaline and acid waters, inductor, capacitor, resistor

Procedia PDF Downloads 112

Authors: M. Ezzat, Y. Zaghloul, T. Sorour, A. Hefny, M. Eid

Abstract:

Ultimate capacity of large diameter bored piles is usually determined from pile loading tests as recommended by several international codes and foundation design standards. However, loading of this type of piles till achieving apparent failure is practically seldom. In this paper, numerical analyses are carried out to simulate load test of a large diameter bored pile performed at the location of Alzey highway bridge project (Germany). Test results of pile load settlement relationship till failure as well as results of the base and shaft resistances are available. Apparent failure was indicated in this test by the significant increase of the induced settlement during the last load increment applied on the pile head. Measurements of this pile load test are used to assess the quality of the numerical models investigated. Three different material soil models are implemented in the analyses: Mohr coulomb (MC), Soft soil (SS), and Modified Mohr coulomb (MMC). Very good agreement is obtained between the field measured settlement and the calculated settlement using the MMC model. Results of analysis showed also that the MMC constitutive model is superior to MC, and SS models in predicting the ultimate base and shaft resistances of the large diameter bored pile. After calibrating the numerical model, behavior of large diameter bored piles under axial loads is discussed and the formation of the plastic zone around the pile is explored. Results obtained showed that the plastic zone below the base of the pile at failure extended laterally to about four times the pile diameter and vertically to about three times the pile diameter.

Keywords: ultimate capacity, large diameter bored piles, plastic zone, failure, pile load test

Procedia PDF Downloads 143

Authors: Kuo-Wei Hsu, Jen-Chih, Chao, Pei-Chen, Wu

Abstract:

With the rapid development of global economy, the increasing population, the highly industrialization, greenhouse gas emission and the ozone layer damage, the Global Warming happens. Facing the impact of global warming, the issue of “green transportation” began to be valued and promoted in each city. Taichung has been elected as the model of low-carbon city in Taiwan. To comply with international trends and the government policy, we tried to promote the energy saving and carbon reduction to create a “low-carbon Taichung with green life and eco-friendly economy”. To cooperate with the “green transportation” project, Taichung has promoted a number of public transports constructions and traffic policy in recent years like BRT, MRT, etc. The elevated railway is one of those important constructions. Cooperating with the green transport policy, elevated railway could help to achieve the carbon reduction for this low-carbon city. The current studies of the carbon emissions associated with railways and roads are focusing on the assessment on paving material, institutional policy and economic benefit. Except for changing the mode of transportation, elevated railways/roads also create space under the bridge. However, there is no research about the carbon emissions of the space underneath the elevated section up until now. This study investigated the effect of railway track elevation project in Taichung based on the carbon emissions and the factors that affect carbon emissions by research related theory and literature analysis. This study concluded that : railway track elevation increased the public transit, the bike lanes, the green areas and walking spaces. In the other hand it reduced the traffic congestions, the use of motorcycles as well as automobiles for carbon emissions.

Keywords: low-carbon city, green transportation, carbon emissions, Taichung, Taiwan

Procedia PDF Downloads 533

Authors: Suneel Kumar, Nanda Kumar J. Sreelal Sreedhar, Suchibrata Sen, V. Muralidharan,

Abstract:

Fan technology is very critical and crucial for any aero engine technology. The fan disc forms a critical part of the fan module. It is an airworthiness requirement to have a metrological qualified quality disc. The current study uses a tactile probing and scanning on an articulated measuring machine (AMM), a bridge type coordinate measuring machine (CMM) and Metrology software for intermediate and final dimensional and geometrical verification during the prototype development of the disc manufactured through forging and machining process. The circumferential dovetails manufactured through the milling process are evaluated based on the evaluated and analysed metrological process. To perform metrological optimization a change of philosophy is needed making quality measurements available as fast as possible to improve process knowledge and accelerate the process but with accuracy, precise and traceable measurements. The offline CMM programming for inspection and optimisation of the CMM inspection plan are crucial portions of the study and discussed. The dimensional measurement plan as per the ASME B 89.7.2 standard to reach an optimised CMM measurement plan and strategy are an important requirement. The probing strategy, stylus configuration, and approximation strategy effects on the measurements of circumferential dovetail measurements of the developmental prototype disc are discussed. The results were discussed in the form of enhancement of the R &R (repeatability and reproducibility) values with uncertainty levels within the desired limits. The findings from the measurement strategy adopted for disc dovetail evaluation and inspection time optimisation are discussed with the help of various analyses and graphical outputs obtained from the verification process.

Keywords: coordinate measuring machine, CMM, aero engine, articulated measuring machine, fan disc

Procedia PDF Downloads 107

Authors: Mark Kennedy, E. Bantugon, Noruane A. Daileg

Abstract:

Leaks arising from aircraft fuel tanks is a protracted problem for the aircraft manufacturers, operators, and maintenance crews. It principally arises from stress, structural defects, or degraded sealants as the aircraft age. It can be ignited by different sources, which can result in catastrophic flight and consequences, exhibiting a major drain both on time and budget. In order to mitigate and eliminate this kind of problem, the researcher produced an experimental sealant having a base material of natural tree resin, the Pili Tree Resin. Aside from producing an experimental sealant, the main objective of this research is to analyze its physical, chemical, mechanical, thermal, and rheological properties, which is beneficial and effective for specific aircraft parts, particularly the integral fuel tank. The experimental method of research was utilized in this study since it is a product invention. This study comprises two parts, specifically the Optimization Process and the Characterization Process. In the Optimization Process, the experimental sealant was subjected to the Flammability Test, an important test and consideration according to 14 Code of Federal Regulation Appendix N, Part 25 - Fuel Tank Flammability Exposure and Reliability Analysis, to get the most suitable formulation. Followed by the Characterization Process, where the formulated experimental sealant has undergone thirty-eight (38) different standard testing including Organoleptic, Instrumental Color Measurement Test, Smoothness of Appearance Test, Miscibility Test, Boiling Point Test, Flash Point Test, Curing Time, Adhesive Test, Toxicity Test, Shore A Hardness Test, Compressive Strength, Shear Strength, Static Bending Strength, Tensile Strength, Peel Strength Test, Knife Test, Adhesion by Tape Test, Leakage Test), Drip Test, Thermogravimetry-Differential Thermal Analysis (TG-DTA), Differential Scanning Calorimetry, Calorific Value, Viscosity Test, Creep Test, and Anti-Sag Resistance Test to determine and analyze the five (5) material properties of the sealant. The numerical values of the mentioned tests are determined using product application, testing, and calculation. These values are then used to calculate the efficiency of the experimental sealant. Accordingly, this efficiency is the means of comparison between the experimental and commercial sealant. Based on the results of the different standard testing conducted, the experimental sealant exceeded all the data results of the commercial sealant. This result shows that the physicochemical-mechanical, thermal, and rheological properties of the experimental sealant are far more effective as an aircraft integral fuel tank sealant alternative in comparison to the commercial sealant. Therefore, Pili Tree possesses a new role and function: a source of ingredients in sealant production.

Keywords: Aircraft Integral Fuel Tank, Physicochemi-mechanical, Pili Tree Resin, Properties, Rheological, Sealant, Thermal

Procedia PDF Downloads 294

Authors: Aida Raissi, Holly Wong, Elma Raissi

Abstract:

Background: Connection is a primal need established during infancy and reiterated in many forms of social interaction. When we make connections with others we experience growth, continuity, and gain an understanding of the other’s sense of the world. Feeling socially connected to another individual or community has been shown to increase self-esteem, happiness, and meaning. However, feeling connected to another individual or a specific community may also decrease the motivation to seek connection with more distant individuals or communities. Furthermore, we allow ourselves to interact with those in other communities as apart from us, and in some cases, to dehumanize their existence. Objective: The aim of this project is to bridge the gap between different communities, specifically religious communities and foster feelings of connection as one with all members through the medium of art, specifically photography. Method: Members of all major faiths including Agnosticism, Atheism, Buddhism, Catholicism, Christianity, Ismaili, Jewish, Ja’far Shia, Sunni will be interviewed. Participants will be asked to partake in a brief interview of two parts: A. Answering two questions: 1. What are you most looking forward to in the future, and why? 2. What does religion mean to you? B. Having their picture taken. Our questions aim to elicit individual stories that together, show that we have more in common, than differences, despite our faiths. With the completion of the interviews, the responses will be compiled together and major themes will be identified. Impact: The resulting stories and corresponding individual pictures provide an excellent opportunity to encourage and inspire people to get to know those of other beliefs and values, participate in each other’s communities and develop a sense of oneness within our shared humanity. Knowledge translation: The personal stories, and the common themes they illustrate, will be shared with various audiences, including the general public, academia and targeted groups such as students. This will be done through displaying the photographs and responses at art galleries, conferences, in print and online.

Keywords: social justice, religion, connection, understanding, community

Procedia PDF Downloads 398

Authors: Estephanie S. López Contreras, Vicente Aranda Palacios, Daniela Flores Silva, Felipe Oliveros Olivares, Romina Riquelme Escobedo, Iñaki Westerhout Usabiaga

Abstract:

This research explored whether the context of online instruction has influenced the development of first-year English-teaching students' communication skills, being these speaking and listening. The theoretical basis finds its niche in the need to bridge the gap in knowledge about the Chilean online educational context and the development of English communicative skills. An interpretative paradigm and a phenomenological design were implemented in this study. Twenty- two first-year students and two teachers from an English teaching training program participated in the study. The students' ages ranged from 18 to 26 years of age, and the teachers' years of experience ranged from 5 to 13 years in the program. For data collection purposes, semi- structured interviews were applied to both students and teachers. Interview questions were based on the initial conceptualization of the central phenomenon. Observations, field notes, and focus groups with the students are also part of the data collection process. Data analysis considered two-cycle methods. The first included descriptive coding for field notes, initial coding for interviews, and creating a codebook. The second cycle included axial coding for both field notes and interviews. After data analysis, the findings show that students perceived online classes as instances in which active communication cannot always occur. In addition, changes made to the curricula as a consequence of the COVID-19 pandemic have affected students' speaking and listening skills.

Keywords: attitudes, communicative skills, EFL teaching training program, online instruction, and perceptions

Procedia PDF Downloads 119

Authors: Tracy Smith-Carrier

Abstract:

Burgeoning research extols the benefits of innovative experiential learning activities to increase participants’ engagement, enhance their individual learning, and bridge the gap between theory and practice. This presentation discusses findings from a multiple case study on poverty simulation events conducted with two samples: undergraduate students and community participants. After exploring the nascent research on the benefits and limitations of poverty simulation activities, the study explores whether participating in a poverty simulation resulted in changes to participants’ beliefs about the causes and effects of poverty, as well as shifts in their attitudes and actions toward people experiencing poverty. For the purposes of triangulation, quantitative and qualitative data from a variety of sources were analyzed: participant feedback surveys, qualitative responses, and pre, post, and follow-up questionnaires. Findings show statistically significant results (p<.05) from both samples on cumulative scores of the modified Attitudes Toward Poverty Scale, indicating an improvement in participants’ attitudes toward poverty. Although generally positive about their experiences, participating in the simulation did not appear to have prompted participants to take specific actions to reduce poverty. Conclusions drawn from the research study suggest that poverty simulation planners should be wary of adopting scenarios that emphasize, or fail to adequately contextualize, behaviours or responses that might perpetuate individual explanations of poverty. Moreover, organizers must carefully consider how to ensure participants in their audience currently experiencing low-income do not become emotionally distressed, triggered or further marginalized in the process. While overall participants were positive about their experiences in the simulation, the events did not appear to have prompted them to action. Moving beyond the goal of increasing participants’ understandings of poverty, interventions that foster greater engagement in poverty issues over the long-term are necessary.

Keywords: empathy, experiential learning, poverty awareness, poverty simulation

Procedia PDF Downloads 267

Authors: Danièle Peto

Abstract:

A qualitative research based on twenty-eight semi-structured interviews of students in Social Work, in Brussels (Belgium), showed specific results for the Arab and Muslim students: second and third generations immigrants build their identity on the basis of a mix of differentiation with and recognition of their parents' culture of origin. Building a bridge between Modernity and Tradition, they claim active citizenship; at the same time they show and live by values and religious believes which reinforce the link to their parents’ origins. But they present those values and believes as their own rational choices among other choices, all available and rich for our multicultural society. The way they speak of themselves is highly modern. But, they still have to build a third way to find a place for themselves in society: one allowing them to live their religion as a partially public matter (when the Occidental society leaves no such place for religion) while ensuring, at the same time, the development of independent critical thought. On this basis, other semi-structured interviews are being laid with Social workers working with families from diverse ethnic backgrounds. They will verify the reality of those identity and cultural bricolages when those young adults of second and third generations build their own family. In between the theoretical models of traditional family and modern family, shall we find a new model, hybrid and more or less stable, combining some aspects of the former and the latter? The exploratory research phase focuses on three aspects of building a family life in this context : the way those generations play, discursively or not, in between their parents and the society in which they grew up; the importance of intercultural dialogue in this process of building; and testing the hypothesis that some families, in our society, show a special way of courting Modernity.

Keywords: family models, identity bricolages, intercultural, modernity and tradition

Procedia PDF Downloads 301

Authors: Haiping Zhu

Abstract:

The purpose of this work-in-progress paper is to explore how the Chinese philosophic-religious tradition of Taoism impacts on the consumption behaviour of contemporary Chinese consumers. Although much cultural research has been conducted on Chinese consumption behaviours, most studies have approached the subject from Western perspectives. Examination of the limited literature indicates a gap in the knowledge of the relationship of traditional Chinese Taoism philosophy and Chinese consumption behaviour. To bridge this gap, this study examines Chinese consumption behaviour at a Taoist-related Chinese religious festival - the DuanWu festival - in order to seek some understanding of how the Taoism philosophic-religious tradition influences Chinese consumption behaviour from the point of view of the individuals involved. It focuses attention on their expression of Taoism cultural values, purchasing experience and subsequent consumption behaviours. This study undertook multiple methods for Taoist case study data collection: accompanied shopping with Taoists before DuanWu Festival; participant observations during DuanWu Festival; and in-depth interviews in order to explore Taoists consumption behaviours at the end of the Festival. Specifically, the finding from the Taoist case study corroborates and details the influence of the Taoism doctrine: man–nature orientation, Fenshui, ecological effect, and ecological knowledge, on their attitudes toward green purchasing behaviour. Findings from this Taoist case study - one of a series of three Chinese philosophic religious tradition case studies - contribute to the deeper understanding of contemporary Chinese consumers from a non-Western viewpoint and offer initial insights for global marketers to differentiate consumer needs and develop effective marketing strategies.

Keywords: consumer behaviour, culture values, green purchase behaviour, Taoism

Procedia PDF Downloads 253

Authors: Iordana Neamtu, Aurica P. Chiriac, Loredana E. Nita, Mihai Asandulesa, Elena Butnaru, Nita Tudorachi, Alina Diaconu

Abstract:

In the last decade, the attention of many researchers is focused on the synthesis of innovative “intelligent” copolymer structures with great potential for different uses. This considerable scientific interest is stimulated by possibility of the significant improvements in physical, mechanical, thermal and other important specific properties of these materials. Functionalization of polymer in synthesis by designing a suitable composition with the desired properties and applications is recognized as a valuable tool. In this work is presented a comparative study of the properties of the new copolymers poly(maleic anhydride maleic-co-3,9-divinyl-2,4,8,10-tetraoxaspiro[5.5]undecane) and poly(itaconic-anhydride-co-3,9-divinyl-2,4,8,10-tetraoxaspiro[5.5]undecane) obtained by radical polymerization in dioxane, using 2,2′-azobis(2-methylpropionitrile) as free-radical initiator. The comonomers are able for generating special effects as for example network formation, biodegradability and biocompatibility, gel formation capacity, binding properties, amphiphilicity, good oxidative and thermal stability, good film formers, and temperature and pH sensitivity. Maleic anhydride (MA) and also the isostructural analog itaconic anhydride (ITA) as polyfunctional monomers are widely used in the synthesis of reactive macromolecules with linear, hyperbranched and self & assembled structures to prepare high performance engineering, bioengineering and nano engineering materials. The incorporation of spiroacetal groups in polymer structures improves the solubility and the adhesive properties, induce good oxidative and thermal stability, are formers of good fiber or films with good flexibility and tensile strength. Also, the spiroacetal rings induce interactions on ether oxygen such as hydrogen bonds or coordinate bonds with other functional groups determining bulkiness and stiffness. The synthesized copolymers are analyzed by DSC, oscillatory and rotational rheological measurements and dielectric spectroscopy with the aim of underlying the heating behavior, solution viscosity as a function of shear rate and temperature and to investigate the relaxation processes and the motion of functional groups present in side chain around the main chain or bonds of the side chain. Acknowledgments This work was financially supported by the grant of the Romanian National Authority for Scientific Research, CNCS-UEFISCDI, project number PN-II-132/2014 “Magnetic biomimetic supports as alternative strategy for bone tissue engineering and repair’’ (MAGBIOTISS).

Keywords: Poly(maleic anhydride-co-3, 9-divinyl-2, 4, 8, 10-tetraoxaspiro (5.5)undecane); Poly(itaconic anhydride-co-3, 9-divinyl-2, 4, 8, 10-tetraoxaspiro (5.5)undecane); DSC; oscillatory and rotational rheological analysis; dielectric spectroscopy

Procedia PDF Downloads 227

Authors: Maria Luiza D. Ramiento, Maria Lissette D. Lucas

Abstract:

Electricity is said to serve as the backbone of modern technology. Considering this, electricity consumption has dynamically grown due to the continuous demand. An alternative producer of energy concerning electricity must therefore be given focus. Microbial fuel cell wholly characterizes a new method of renewable energy recovery: the direct conversion of organic matter to electricity using bacteria. Electricity is produced as fuel or new food is given to the bacteria. The study concentrated in determining the feasibility of electricity production from local benthic zones. Microbial fuel cells were constructed to harvest the possible electricity and to test the presence of electricity producing microorganisms. Soil samples were gathered from Calumpang River, Palawan Mangrove Forest, Rosario River and Batangas Port. Eleven modules were constructed for the different trials of the soil samples. These modules were made of cathode and anode chambers connected by a salt bridge. For 85 days, the harvested voltage was measured daily. No parameter is added for the first 24 days. For the next 61 days, acetic acid was included in the first and second trials of the modules. Each of the trials of the soil samples gave a positive result in electricity production.There were electricity producing microbes in local benthic zones. It is observed that the higher the organic content of the soil sample, the higher the electricity harvested from it. It is recommended to identify the specific species of the electricity-producing microorganism present in the local benthic zone. Complement experiments are encouraged like determining the kind of soil particles to test its effect on the amount electricity that can be harvested. To pursue the development of microbial fuel cells by building a closed circuit in it is also suggested.

Keywords: microbial fuel cell, benthic zone, electricity, reduction-oxidation reaction, bacteria

Procedia PDF Downloads 400

Authors: Bhavani Veasuvalingam

Abstract:

Case-based learning (CBL) is a popular instructional method aimed to bridge theory to clinical practice. This study aims to explore CBL mixed modality curriculum in influencing students’ learning styles and strategies that support learning. An explanatory sequential mixed method study was employed with initial phase, 44-itemed Felderman’s Index of Learning Style (ILS) questionnaire employed across year one medical students (n=142) using convenience sampling to describe the preferred learning styles. The qualitative phase utilised three focus group discussions (FGD) to explore in depth on the multimodal learning style exhibited by the students. Most students preferred combination of learning stylesthat is reflective, sensing, visual and sequential i.e.: RSVISeq style (24.64%) from the ILS analysis. The frequency of learning preference from processing to understanding were well balanced, with sequential-global domain (66.2%); sensing-intuitive (59.86%), active- reflective (57%), and visual-verbal (51.41%). The qualitative data reported three major themes, namely Theme 1: CBL mixed modalities navigates learners’ learning style; Theme 2: Multimodal learners active learning strategies supports learning. Theme 3: CBL modalities facilitating theory into clinical knowledge. Both quantitative and qualitative study strongly reports the multimodal learning style of the year one medical students. Medical students utilise multimodal learning styles to attain the clinical knowledge when learning with CBL mixed modalities. Educators’ awareness of the multimodal learning style is crucial in delivering the CBL mixed modalities effectively, considering strategic pedagogical support students to engage and learn CBL in bridging the theoretical knowledge into clinical practice.

Keywords: case-based learning, learnign style, medical students, learning

Procedia PDF Downloads 95

Authors: Tahsin A. H. Nishat, Raquib Ahsan

Abstract:

Sensitivity analysis of design parameters of the optimization procedure can become a significant factor while designing any structural system. The objectives of the study are to analyze the sensitivity of deck slab thickness parameter obtained from both the conventional and optimum design methodology of pre-stressed post-tensioned I-girder and deck system and to compare the relative significance of slab thickness. For analysis on conventional method, the values of 14 design parameters obtained by the conventional iterative method of design of a real-life I-girder bridge project have been considered. On the other side for analysis on optimization method, cost optimization of this system has been done using global optimization methodology 'Evolutionary Operation (EVOP)'. The problem, by which optimum values of 14 design parameters have been obtained, contains 14 explicit constraints and 46 implicit constraints. For both types of design parameters, sensitivity analysis has been conducted on deck slab thickness parameter which can become too sensitive for the obtained optimum solution. Deviations of slab thickness on both the upper and lower side of its optimum value have been considered reflecting its realistic possible ranges of variations during construction. In this procedure, the remaining parameters have been kept unchanged. For small deviations from the optimum value, compliance with the explicit and implicit constraints has been examined. Variations in the cost have also been estimated. It is obtained that without violating any constraint deck slab thickness obtained by the conventional method can be increased up to 25 mm whereas slab thickness obtained by cost optimization can be increased only up to 0.3 mm. The obtained result suggests that slab thickness becomes less sensitive in case of conventional method of design. Therefore, for realistic design purpose sensitivity should be conducted for any of the design procedure of girder and deck system.

Keywords: sensitivity analysis, optimum design, evolutionary operations, PC I-girder, deck system

Procedia PDF Downloads 137

Authors: Semayat Fanta, P.M. Mohite, C.S. Upadhyay

Abstract:

Damage meso-model for laminates is one of the most widely applicable approaches for the analysis of damage induced in laminated fiber-reinforced polymeric composites. Damage meso-model for laminates has been developed over the last three decades by many researchers in experimental, theoretical, and analytical methods that have been carried out in micromechanics as well as meso-mechanics analysis approaches. It has been fundamentally developed based on the micromechanical description that aims to predict the damage initiation and evolution until the failure of structure in various loading conditions. The current damage meso-model for laminates aimed to act as a bridge between micromechanics and macro-mechanics of the laminated composite structure. This model considers two meso-constituents for the analysis of damage in ply and interface that imparted from low-velocity impact. The damages considered in this study include fiber breakage, matrix cracking, and diffused damage of the lamina, and delamination of the interface. The damage initiation and evolution in laminae can be modeled in terms of damaged strain energy density using damage parameters and the thermodynamic irreversible forces. Interface damage can be modeled with a new concept of spherical micro-void in the resin-rich zone of interface material. The damage evolution is controlled by the damage parameter (d) and the radius of micro-void (r) from the point of damage nucleation to its saturation. The constitutive martial model for meso-constituents is defined in a user material subroutine VUMAT and implemented in ABAQUS/Explicit finite element modeling tool. The model predicts the damages in the meso-constituents level very accurately and is considered the most effective technique of modeling low-velocity impact simulation for laminated composite structures.

Keywords: mesomodel, laminate, low-energy impact, micromechanics

Procedia PDF Downloads 223

Authors: D. Tappi

Abstract:

In the past decades, the idea of innovation moved from being considered the result of development to being seen as its means. Innovation and its diffusion are indeed keys to the development and economic catch-up of a country. However, the process of diffusing existing innovation in low income countries has demonstrated dependent on inadequate infrastructures and institutions. The paper examines the role of disruptive innovation in bridging the technology gap between high- and low-income countries, overcoming the lack in infrastructures and institutions. In particular, the focus of this paper goes to the role of disruptive innovation in people transportation in Nigeria. Uber, Taxify, and Smartcab are covering a small and interesting market that was underserved, between the high-end private driver markets, the personal car owners and the low-priced traditional cab and the Keke (tricycle). Indeed the small Nigerian middle class and international community have found in the sharing people transportation market a safe, reasonably priced means of transportation in Nigerian big cities. This study uses mainly qualitative data collection methods in the form of semi-structured interviews with major players and users and quantitative data analysis in the form of a survey among users in order to assess the role of these new transportation modes in shaping the market and even creating a new niche. This paper shows how the new sharing economy in people transportation is creating new solutions to old problems as well as creating new challenges for both the existing market players and institutions. By doing so, the paper shows how disruptive innovations applied to low income countries, not only can overcome the lacking infrastructure problem but could also help bridge the technology gap between those and high income countries. This contribution proves that it is indeed exactly because the market presents these obstacles that disruptive innovations can succeed in countries such as Nigeria.

Keywords: development, disruptive innovation, sharing economy, technology gap

Procedia PDF Downloads 119