Search results for: hyperchaos-based random number generator

Authors: Sanguk Nam, Van Ha Nguyen, Hanjung Song

Abstract:

For low-power applications such as adapters for portable devices and USB chargers, the primary side regulation (PSR) fly-back converter is widely used in lieu of the conventional fly-back converter using opto-coupler because of its simpler structure and lower cost. In the literature, there has been studies focusing on the design of PSR circuit; however, the conventional sensing method in PSR circuit using RC delay has a lower accuracy as compared to the conventional fly-back converter using opto-coupler. In this paper, we propose a novel PWM/PFM controller using new sensing technique for the PSR fly-back converter which can control an accurate output voltage. The conventional PSR circuit can sense the output voltage information from the auxiliary winding to regulate the duty cycle of the clock that control the output voltage. In the sensing signal waveform, there has two transient points at time the voltage equals to Vout+VD and Vout, respectively. In other to sense the output voltage, the PSR circuit must detect the time at which the current of the diode at the output equals to zero. In the conventional PSR flyback-converter, the sensing signal at this time has a non-sharp-negative slope that might cause a difficulty in detecting the output voltage information since a delay of sensing signal or switching clock may exist which brings out an unstable operation of PSR fly-back converter. In this paper instead of detecting output voltage at a non-sharp-negative slope, a sharp-positive slope is used to sense the proper information of the output voltage. The proposed PRS circuit consists of a saw-tooth generator, a summing circuit, a sample and hold circuit and a peak detector. Besides, there is also the start-up circuit which protects the chip from high surge current when the converter is turned on. Additionally, to reduce the standby power loss, a second mode which operates in a low frequency is designed beside the main mode at high frequency. In general, the operation of the proposed PSR circuit can be summarized as following: At the time the output information is sensed from the auxiliary winding, a saw-tooth signal from the saw-tooth generator is generated. Then, both of these signals are summed using a summing circuit. After this process, the slope of the peak of the sensing signal at the time diode current is zero becomes positive and sharp that make the peak easy to detect. The output of the summing circuit then is fed into a peak detector and the sample and hold circuit; hence, the output voltage can be properly sensed. By this way, we can sense more accurate output voltage information and extend margin even circuit is delayed or even there is the existence of noise by using only a simple circuit structure as compared with conventional circuits while the performance can be sufficiently enhanced. Circuit verification was carried out using 0.35μm 700V Magnachip process. The simulation result of sensing signal shows a maximum error of 5mV under various load and line conditions which means the operation of the converter is stable. As compared to the conventional circuit, we achieved very small error only used analog circuits compare with conventional circuits. In this paper, a PWM/PFM controller using a simple and effective sensing method for PSR fly-back converter has been presented in this paper. The circuit structure is simple as compared with the conventional designs. The gained results from simulation confirmed the idea of the design

Keywords: primary side regulation, PSR, sensing technique, peak detector, PWM/PFM control, fly-back converter

Procedia PDF Downloads 321

Authors: Wasfi Al Salamat, Shaker Al-Kharouf

Abstract:

This study aims to examine the determinants of financial stability for 13 commercial banks listed on the Amman stock exchange (ASE) over the period (2007-2016) after controlling for the independent variables: return on equity (ROE), return on assets (ROA), earnings per share (EPS), growth in gross domestic product (GDP), inflation rate and debt ratio to measure the financial stability by three main variables: capital adequacy, non-performing loans and the number of returned checks. The balanced panel data statistical approach has been used for data analysis. Results are estimated by using multiple regression models. The empirical results suggested that there is statistically significant negative effect of inflation rate and debt ratio on the capital adequacy while there is statistically significant positive effect of growth in gross domestic product on capital adequacy. In contrast, there is statistically significant negative effect of return on equity and growth in gross domestic product on the non-performing loans while there is statistically significant positive effect of inflation rate on non-performing loans. Finally, there is statistically significant negative effect of growth in gross domestic product on the number of returned checks while there is statistically significant positive effect of inflation rate on the number of returned checks.

Keywords: capital adequacy, financial stability, non-performing loans, number of returned checks, ASE

Procedia PDF Downloads 197

Authors: L. Sierra, N. Gambetta, M. A. Garcia-Benau, M. Orta

Abstract:

Financial scandals and financial crisis have led to an international debate on the value of auditing. In recent years there have been significant legislative reforms aiming to increase markets’ confidence in audit services. In particular, there has been a significant debate on the need to improve the communication of auditors with audit reports users as a way to improve its informative value and thus, to improve audit quality. The International Auditing and Assurance Standards Board (IAASB) has proposed changes to the audit report standards. The International Standard on Auditing 701, Communicating Key Audit Matters (KAM) in the Independent Auditor's Report, has introduced new concepts that go beyond the auditor's opinion and requires to disclose the risks that, from the auditor's point of view, are more significant in the audited company information. Focusing on the companies included in the Financial Times Stock Exchange 100 index, this study aims to focus on the analysis of the determinants of the number of KAM disclosed by the auditor in the audit report and moreover, the analysis of the determinants of the different type of KAM reported during the period 2013-2015. To test the hypotheses in the empirical research, two different models have been used. The first one is a linear regression model to identify the client’s characteristics, industry sector and auditor’s characteristics that are related to the number of KAM disclosed in the audit report. Secondly, a logistic regression model is used to identify the determinants of the number of each KAM type disclosed in the audit report; in line with the risk-based approach to auditing financial statements, we categorized the KAM in 2 groups: Entity-level KAM and Accounting-level KAM. Regarding the auditor’s characteristics impact on the KAM disclosure, the results show that PwC tends to report a larger number of KAM while KPMG tends to report less KAM in the audit report. Further, PwC reports a larger number of entity-level risk KAM while KPMG reports less account-level risk KAM. The results also show that companies paying higher fees tend to have more entity-level risk KAM and less account-level risk KAM. The materiality level is positively related to the number of account-level risk KAM. Additionally, these study results show that the relationship between client’s characteristics and number of KAM is more evident in account-level risk KAM than in entity-level risk KAM. A highly leveraged company carries a great deal of risk, but due to this, they are usually subject to strong capital providers monitoring resulting in less account-level risk KAM. The results reveal that the number of account-level risk KAM is strongly related to the industry sector in which the company operates assets. This study helps to understand the UK audit market, provides information to auditors and finally, it opens new research avenues in the academia.

Keywords: FTSE 100, IAS 701, key audit matters, auditor’s characteristics, client’s characteristics

Procedia PDF Downloads 210

Authors: Sireesha Tamada, Debraj Bhattacharjee, Pranab K. Dan, Prabha Bhola

Abstract:

The most important component in an automotive transmission system is the gearbox which controls the speed of the vehicle. In an automatic transmission, the right positioning of actuators ensures efficient transmission mechanism embodiment, wherein the challenge lies in formulating the number of actuators associated with modelling a gearbox. Data with respect to actuation and gear shifting sequence has been retrieved from the available literature, including patent documents, and has been used in this proposed heuristics based methodology for modelling actuation sequence in a gear box. This paper presents a methodological approach in designing a gearbox for the purpose of obtaining an optimal shifting sequence. The computational model considers factors namely, the number of stages and gear teeth as input parameters since these two are the determinants of the gear ratios in an epicyclic gear train. The proposed transmission schematic or stick diagram aids in developing the gearbox layout design. The number of iterations and development time required to design a gearbox layout is reduced by using this approach.

Keywords: automatic transmission, gear-shifting, multi-stage planetary gearbox, rank ordered clustering

Procedia PDF Downloads 304

Authors: Sheetla Prasad

Abstract:

The objective of this study is ‘discovering the real psyche of human beings for prediction of mode, direction and strength of the potential of actions of the individual. The human face was taken as a source of central point to search for the route of real psyche. Analysis of the face architecture (shape and salient features of face) was done by three directional photographs ( 600 left and right and camera facing) of human beings. The shapes and features of the human face were scaled in 177 units on the basis of face–features locations (FFL). The mathematical analysis was done of FFLs by self developed and standardized formula. At this phase, 800 samples were taken from the population of students, teachers, advocates, administrative officers, and common persons. The finding shows that real psyche has two external rings (ER). These ER are itself generator of two independent psyches (manifested and manipulated). Prima-facie, it was proved that micro differences in FFLs have potential to predict the state of art of the human psyche. The potential of psyches was determined by the saving and distribution of mental energy. It was also mathematically proved.

Keywords: face architecture, psyche, potential, face functional ratio, external rings

Procedia PDF Downloads 487

Authors: Jian Huang, Weixin Qian, Haitao Zhang, Weiyong Ying

Abstract:

Cobalt-gadolinium catalyst for Fischer-Tropsch synthesis was prepared by impregnation method with commercial silica gel, and its texture properties were characterized by BET, XRD, and TPR. The catalytic performance of the catalyst was tested in a fixed bed reactor. The results showed that the addition of gadolinium to the cobalt catalyst might decrease the size of cobalt particles, and increased the dispersion of catalytic active cobalt phases. The carbon number distributions for the catalysts was calculated by ASF equation.

Keywords: Fischer-Tropsch synthesis, cobalt-based catalysts, gadolinium, carbon number distributions

Procedia PDF Downloads 358

Authors: Khalid Javed, Rashid Mahmood

Abstract:

The constitution empowers the Federal Government to collect taxes on income other than agricultural income, taxes on capital value, customs, excise duties and sales taxes. The Central Board of Revenue (CBR) and its subordinate departments administer the tax system. Each of the three principal taxes has a different history and different set of issues. For a large number of income tax payers the core of the business process is pre-audit and assessment by a tax official. This process gives considerable discretion to tax officials, with potential for abuse. Moreover, this process is also not tenable as the number of taxpayers increase. The report is focused on a total overhaul of the process and organization of income tax. Sales tax is recent and its process and organization is adjusted to the needs of an expanding tax base. These are based on self-assessment and selective audit. Similarly, in customs the accent is on accelerating and broadening the changes begun in recent years. Before long, central excise will be subsumed in sales tax. During the nineties, despite many changes in the tax regime and introduction of withholding and presumptive taxes, Federal Government tax to GDP ratio has varied narrowly around eleven percent. The tax base has grown but still remains narrow and skewed. The number of income tax filers is around one million.

Keywords: central board of revenue, GDP, sale tax, income tax

Procedia PDF Downloads 418

Authors: Dhvanidevi N. Jadeja, Daya S. Kaul, Anurag A. Kandya

Abstract:

Municipal Solid Waste (MSW) collection in a city is performed in less effective manner which results in the poor management of the environment and natural resources. Municipal corporation does not possess efficient waste management and recycling programs because of the complex task involving many factors. Solid waste collection system depends upon various factors such as manpower, number and size of vehicles, transfer station size, dustbin size and weight, on-road traffic, and many others. These factors affect the collection cost, energy and overall municipal tax for the city. Generally, different types of waste are scattered throughout the city in a heterogeneous way that poses changes for efficient collection of solid waste. Efficient waste collection and transportation strategy must be effectively undertaken which will include optimization of routes, volume of waste, and manpower. Being these optimized, the overall cost can be reduced as the fuel and energy requirements would be less and also the municipal waste taxes levied will be less. To carry out the optimization study of collection system various data needs to be collected from the Ahmedabad municipal corporation such as amount of waste generated per day, number of workers, collection schedule, road maps, number of transfer station, location of transfer station, number of equipment (tractors, machineries), number of zones, route of collection etc. The ArcGis Network Analyst is introduced for the best routing identification applied in municipal waste collection. The simulation consists of scenarios of visiting loading spots in the municipality of Ahmedabad, considering dynamic factors like network traffic changes, closed roads due to natural or technical causes. Different routes were selected in a particular area of Ahmedabad city, and present routes were optimized to reduce the length of the routes, by using ArcGis Network Analyst. The result indicates up to 35% length minimization in the routes.

Keywords: collection routes, efficiency, municipal solid waste, optimization

Procedia PDF Downloads 118

Authors: Behzad Ali Khan, M. Zubair Akbar Qureshi

Abstract:

The article analyzes the Darcy Forchheimer 2D Hybrid ferrofluid. The flow of a Hybrid ferrofluid is made due to an unsteady porous channel. The classical liquid water is treated as a based liquid. The flow in the permeable region is characterized by the Darcy-Forchheimer relation. Heat transfer phenomena are studied during the flow. The transformation of a partial differential set of equations into a strong ordinary differential frame is formed through appropriate variables. The numerical Shooting Method is executed for solving the simplified set of equations. In addition, a numerical analysis (ND-Solve) is utilized for the convergence of the applied technique. The influence of some flow model quantities like Pr (Prandtle number), r (porous medium parameter), F (Darcy-porous medium parameter), Re (Reynolds number), Pe (Peclet number) on velocity and temperature field are scrutinized and studied through sketches. Certain physical factors like f ''(η) (skin friction coefficient) and θ^'(η) (rate of heat transfer) are first derived and then presented through tables.

Keywords: darcy forcheimer, hybrid ferro fluid, porous medium, porous channel

Procedia PDF Downloads 155

Authors: Abolade Olajoke, Adigun Folasade Oyenike, Odunjo Oluronke Omolola Olaleye, Babajide Rotimi

Abstract:

Against the shortfall associated with unprecedented urbanization in most cities of the world, coupled with rapid expansion of outer boundaries, is the resultant birth of the development of new towns. The paper therefore examines the impacts of Ibeju - Lekki New Town on Neighbouring communities of Ibeju Lekki. Random systematic sampling was employed elicit relevant information from a total number of 269 residents at interval of five buildings in four neighbouring communities. Descriptive statistics was employed to test for the socioeconomic characteristics of respondents, problems faced by government officials during the implementation and monitoring process. Likert scale was employed to ascertain respondents view on the impact of the new town on neighbouring communities. Result from the findings shows that male (56.9%) are the most dominant occupant in the study area of which most (68.1%) fall within the most the active age group (18-39 and 40-59 years). Results further shows that 36% of the total respondents are traders and majority (32%) earn below government salary wage cap of ₦18000 thus indicating that majority of the respondents are petty traders. Results of findings from development authority reveals that the major problem encountered during monitoring and implementation is harassment of government officials (35%). Result of likert scale further show that new town has brought increase in intensity of land use within neighbouring communities (RAI 3.65), provision of job opportunity (RAI 3.57). This have consequently improve standard of living of the neighbouring community (RAI 3.27). On the contrary some (RAI 1.97) opined that attention should paid to provision of power supply and provision of recreation facilities (RAI I.63). The study recommends that government should make adequate provisions for basic facilities such power supply, adequate health care system, basic education and provision of healthy portable water. This should be given utmost priority to enhance the living condition of residents. To forestall attack from residents’ adequate security measures should be provided as backup for Government official during implementation and monitoring. Appropriate sanction to illegal occupants and demolition of illegal structures should be fully implemented, This will indubitably prevent haphazard development and also promote a liveable environment. Against the shortfall associated with unprecedented urbanization in most cities of the world, coupled with rapid expansion of outer boundaries, is the resultant birth of the development of new towns. The paper therefore examines the impacts of Ibeju - Lekki New Town on Neighbouring communities of Ibeju Lekki. Random systematic sampling was employed elicit relevant information from a total number of 269 residents at interval of five buildings in four neighbouring communities. Descriptive statistics was employed to test for the socioeconomic characteristics of respondents, problems faced by government officials during the implementation and monitoring process. Likert scale was employed to ascertain respondents view on the impact of the new town on neighbouring communities. Result from the findings shows that male (56.9%) are the most dominant occupant in the study area of which most (68.1%) fall within the most the active age group (18-39 and 40-59 years). Results further shows that 36% of the total respondents are traders and majority (32%) earn below government salary wage cap of ₦18000 thus indicating that majority of the respondents are petty traders. Results of findings from development authority reveals that the major problem encountered during monitoring and implementation is harassment of government officials (35%) Result of likert scale further show that new town has brought increase in intensity of land use within neighbouring communities (RAI 3.65), provision of job opportunity (RAI 3.57). This have consequently improve standard of living of the neighbouring community (RAI 3.27). On the contrary some (RAI 1.97) opined that attention should paid to provision of power supply and provision of recreation facilities (RAI I.63). The study recommends that government should make adequate provisions for basic facilities such power supply, adequate health care system, basic education and provision of healthy portable water. This should be given utmost priority to enhance the living condition of residents. To forestall attack from residents’ adequate security measures should be provided as backup for Government official during implementation and monitoring. Appropriate sanction to illegal occupants and demolition of illegal structures should be fully implemented, This will indubitably prevent haphazard development and also promote a liveable environment.

Keywords: new town, urbanization, infrastructure boundary

Procedia PDF Downloads 394

Authors: B. S. Akhmetov, P. T.Kharitonov, L. Sh. Balgabayeva, O. V. Kisseleva, T. S. Kartbayev

Abstract:

This article analyzes the applicability of known renewable energy technical means as mobile power sources under the field and extreme conditions. The requirements are determined for the parameters of mobile micro-HPP. The application prospectively of the mobile micro-HPP with intelligent control systems is proved for this purpose. Variants of low-speed electric generators for micro HPP are given. Variants of designs for mobile micro HPP are presented with the direct (gearless) transfer of torque from the hydraulic drive to the rotor of the electric generator. Variant of the hydraulic drive for micro HPP is described workable at low water flows. A general structure of the micro HPP intelligent system control is offered that implements the principle of maximum energy efficiency. The legitimacy of construction and application of mobile micro HPP is proved as electrical power sources for life safety of people under the field and extreme conditions.

Keywords: mobile micro-hydro powerplants, information management systems, hydraulic drive, computer science

Procedia PDF Downloads 391

Authors: Andi Darmawan, Dewi Retno Sari Saputro, Purnami Widyaningsih

Abstract:

Diabetes mellitus (DM) is a chronic disease in human that occurred if pancreas cannot produce enough of insulin hormone or the body uses ineffectively insulin hormone which causes increasing level of glucose in the blood, or it was called hyperglycemia. In Indonesia, DM is a serious disease on health because it can cause blindness, kidney disease, diabetic feet (gangrene), and stroke. The type of DM criteria can also be divided based on the main causes; they are DM type 1, type 2, and gestational. Diabetes type 1 or previously known as insulin-independent diabetes is due to a lack of production of insulin hormone. Diabetes type 2 or previously known as non-insulin dependent diabetes is due to ineffective use of insulin while gestational diabetes is a hyperglycemia that found during pregnancy. The most one type commonly found in patient is DM type 2. The main factors of this disease are genetic (A) and life style (E). Those disease with 2 factors can be constructed with additive genetic and unique environment (AE) model. In this article was discussed parameter estimation of AE model using Bayesian method and the inheritance character simulation on parent-offspring. On the AE model, there are response variable, predictor variables, and parameters were capable of representing the number of population on research. The population can be measured through a taken random sample. The response and predictor variables can be determined by sample while the parameters are unknown, so it was required to estimate the parameters based on the sample. Estimation of AE model parameters was obtained based on a joint posterior distribution. The simulation was conducted to get the value of genetic variance and life style variance. The results of simulation are 0.3600 for genetic variance and 0.0899 for life style variance. Therefore, the variance of genetic factor in DM type 2 is greater than life style.

Keywords: AE model, Bayesian method, diabetes mellitus type 2, genetic, life style

Procedia PDF Downloads 256

Authors: Sanghyeon Kim, Cheolung Cheong

Abstract:

Savonius wind turbines are a drag-type of vertical-axis wind turbine that has been used most commonly as a small-scale wind generator. However, noise is a main hindrance to wide spreading of Savonius wind turbines, just like other wind turbines. Although noise levels radiating from Savonius wind turbines may be relatively low because of their small size, they induce relatively high annoyance due to their prolonged noise exposure to the near community. Therefore, aerodynamic noise of small vertical-axis wind turbines is one of most important design parameters. In this paper, aerodynamic noise characteristics of Savonius wind turbines are investigated using the hybrid CAA techniques, and their low noise designs are proposed based on understanding of noise generation mechanism. First, flow field around the turbine are analyzed by solving 3-D unsteady incompressible RANS equations. Then, noise radiation is predicted using the Ffowcs Williams and Hawkings equation. Two distinct harmonic noise components, the well-know BPF components and the harmonics whose fundamental frequency is much higher than the BPF are identified. On a basis of this finding, S-shaped blades are proposed as low noise designs and it can reduce the noise levels of Savonius wind turbines by up to 2.7 dB.

Keywords: aerodynamic noise, Savonius wind turbine, vertical-axis wind turbine

Procedia PDF Downloads 432

Authors: A. Sohouli, A. Suleman

Abstract:

This study focuses on reliability analysis of variable stiffness composite laminate structures to investigate the potential structural improvement compared to conventional (straight fibers) composite laminate structures. A computational framework was developed which it consists of a deterministic design step and reliability analysis. The optimization part is Discrete Material Optimization (DMO) and the reliability of the structure is computed by Monte Carlo Simulation (MCS) after using Stochastic Response Surface Method (SRSM). The design driver in deterministic optimization is the maximum stiffness, while optimization method concerns certain manufacturing constraints to attain industrial relevance. These manufacturing constraints are the change of orientation between adjacent patches cannot be too large and the maximum number of successive plies of a particular fiber orientation should not be too high. Variable stiffness composites may be manufactured by Automated Fiber Machines (AFP) which provides consistent quality with good production rates. However, laps and gaps are the most important challenges to steer fibers that effect on the performance of the structures. In this study, the optimal curved fiber paths at each layer of composites are designed in the first step by DMO, and then the reliability analysis is applied to investigate the sensitivity of the structure with different standard deviations compared to the straight fiber angle composites. The random variables are material properties and loads on the structures. The results show that the variable stiffness composite laminate structures are much more reliable, even for high standard deviation of material properties, than the conventional composite laminate structures. The reason is that the variable stiffness composite laminates allow tailoring stiffness and provide the possibility of adjusting stress and strain distribution favorably in the structures.

Keywords: material optimization, Monte Carlo simulation, reliability analysis, response surface method, variable stiffness composite structures

Procedia PDF Downloads 497

Authors: Sameena Tarannum, S. Pranesh

Abstract:

A nonlinear study of triple diffusive convection in a rotating couple stress liquid has been analysed. It is performed to study the effect of heat and mass transfer by deriving Ginzburg-Landau equation. Heat and mass transfer are quantified in terms of Nusselt number and Sherwood numbers, which are obtained as a function of thermal and solute Rayleigh numbers. The obtained Ginzburg-Landau equation is Bernoulli equation, and it has been elucidated numerically by using Mathematica. The effects of couple stress parameter, solute Rayleigh numbers, and Taylor number on the onset of convection and heat and mass transfer have been examined. It is found that the effects of couple stress parameter and Taylor number are to stabilize the system and to increase the heat and mass transfer.

Keywords: couple stress liquid, Ginzburg-Landau model, rotation, triple diffusive convection

Procedia PDF Downloads 319

Authors: Juliane P. De Oliveira, Carlos H. Dos Santos, Marcia Shoji, Maria E. C. Ferreira, Natalia U. Yamaguchi

Abstract:

The construction sector is considered a major generator of environmental impacts due to the high consumption of natural resources and waste generation. Thus, this article aims to evaluate the performance of a concrete produced by the partial and total replacement of natural coarse aggregate by recycled coarse aggregate, derived from the concrete residue of buildings and demolitions. The study was made by comparing the compressive strength and absorption of three different concrete traces, keeping the water/cement factor of 0.60 and changing only the proportions of recycled coarse aggregate between 0%, 50% and 100%. Traces 50% and 100% obtained good results by comparing the actual specific mass, because the material used is lighter to the natural coarse aggregate. It was concluded that the concrete produced with recycled aggregates, even with inferior results, can be used where it is not needed a structural function, giving an adequate destination to the construction and demolition waste and consequently reducing the extraction and consumption of natural resources.

Keywords: green concrete, recycled aggregate, recycling, sustainable development

Procedia PDF Downloads 131

Authors: Fidelia A. Orji, Julita Vassileva

Abstract:

This research aims to develop machine learning models for students' academic performance and study strategy prediction, which could be generalized to all courses in higher education. Key learning attributes (intrinsic, extrinsic, autonomy, relatedness, competence, and self-esteem) used in building the models are chosen based on prior studies, which revealed that the attributes are essential in students’ learning process. Previous studies revealed the individual effects of each of these attributes on students’ learning progress. However, few studies have investigated the combined effect of the attributes in predicting student study strategy and academic performance to reduce the dropout rate. To bridge this gap, we used Scikit-learn in python to build five machine learning models (Decision Tree, K-Nearest Neighbour, Random Forest, Linear/Logistic Regression, and Support Vector Machine) for both regression and classification tasks to perform our analysis. The models were trained, evaluated, and tested for accuracy using 924 university dentistry students' data collected by Chilean authors through quantitative research design. A comparative analysis of the models revealed that the tree-based models such as the random forest (with prediction accuracy of 94.9%) and decision tree show the best results compared to the linear, support vector, and k-nearest neighbours. The models built in this research can be used in predicting student performance and study strategy so that appropriate interventions could be implemented to improve student learning progress. Thus, incorporating strategies that could improve diverse student learning attributes in the design of online educational systems may increase the likelihood of students continuing with their learning tasks as required. Moreover, the results show that the attributes could be modelled together and used to adapt/personalize the learning process.

Keywords: classification models, learning strategy, predictive modeling, regression models, student academic performance, student motivation, supervised machine learning

Procedia PDF Downloads 105

Authors: Vijaya K. Srivastava, Davide Spinello

Abstract:

This paper presents established 3ⁿ enumeration procedure for mixed integer optimization problems for solving multi-objective reliability and redundancy allocation problem subject to design constraints. The formulated problem is to find the optimum level of unit reliability and the number of units for each subsystem. A number of illustrative examples are provided and compared to indicate the application of the superiority of the proposed method.

Keywords: integer programming, mixed integer programming, multi-objective optimization, Reliability Redundancy Allocation

Procedia PDF Downloads 153

Authors: T. Aragaw, P. Gari

Abstract:

In spite of social, political, and economic marginalization, women are still considered as the backbone of Ethiopia, one of the least developed countries in the world. The general purpose of this study was to assess factors that affect participation of women in politics, social and economic decisions at Kelem-Wollega Administrative Zone of Oromia Regional State, Ethiopia. Data used in this paper is mainly primary, and a few secondary data were incorporated. Respondents were selected using a systematic random sampling method and were placed questionnaires containing open-ended and closed-ended. Focus group discussion was also used for the study subjects in two offices. According to the information collected from the KWAZ Development and Social Service Office, a total of 18,473 tax-paying employees are present in the Zone, which is 14% of the total population of the Zone. Among the total number of employees in the Zone, 2,617 have been recruited for this study based on the criteria stated. This showed 1.8% of them were comprised of several churches and religious owned integrated development projects in the KWAZ. The 2,103 (80.34%) study participants responded personally, and they completed and returned the questionnaire to the researchers. The study revealed that in public institutions existed in KWAZ, the majority of women were having an educational status of diploma and lower, practicing lower non-decision making and leadership positions. Conclusion: Major barriers hindering women include: Socio-cultural attitudes, lack of necessary experience, education, the burden of domestic responsibilities, and lack of role models of women leaders in the Zone. Empowerment of women via social organizations, critical involvement of the government, and Affirmative action for women is critical. Further research is needed on the scope and challenges in implementing the strategies.

Keywords: women, affirmative action, leadership, empowerment, Ethiopia

Procedia PDF Downloads 170

Authors: Evren Ozgur, Kasim Kocak

Abstract:

As a result of global warming and climate change, air temperature has increased and will continue to increase in the future. Increases in air temperatures have effects on a large number of variables in meteorology. One of the most important effects is the changes in the types of precipitation, especially in mid-latitudes. Because of increasing air temperatures, less snowfall was observed in the eastern parts of Turkey. Snowfall provides most of the water supply in spring and summer months, especially in mountainous regions of Turkey. When the temperature begins to increase in spring season, this snow starts to melt and plays an important role in agricultural purposes, drinking water supply and energy production. On the other hand, defining the snow season is very crucial especially in mountainous areas which have winter tourism opportunities. A reduction in the length of the snow season (LSS) in these regions will result in serious consequences in the long run. In the study, snow season was examined for 10 meteorological stations that are located above the altitude of 1000m. These stations have decreasing trends in the ratio of number of snowy days to total precipitation days considering earlier studies. Daily precipitation records with the observation period of 1971-2011 were used in the study. Then, the observation period was separated into 4 non-overlapping parts in order to identify decadal variations. Changes in the length of the snow season with increasing temperatures were obtained for these stations. The results of LSS were evaluated with the number of snowy days for each station. All stations have decreasing trend in number of snowy days for 1971-2011 period. In addition, seven of the results are statistically significant. Besides, decrease is observed regarding the length of snow season for studied stations. The decrease varies between 6.6 and 47.6 days according to decadal snow season averages of the stations.

Keywords: climate change, global warming, precipitation, snowfall, Turkey

Procedia PDF Downloads 153

Authors: G. H. B. Dilhari, A. A. D. T. Saparamadu

Abstract:

Sri Lanka is one of the prominent countries for the coir production. The coir is one of the by-products of the coconut and the coir industry is considered to be one of the traditional industries in Sri Lanka. Because of the inherent nature of the coir industry, labourers play a significant role in the coir production process. The study has analyzed the determinants of the income of the household level coir yarn labourers. The study was conducted in the Kumarakanda Grama Niladhari division. Simple random sampling was used to generate a sample of 100 household level coir yarn labourers and structured questionnaire, personal interviews, and discussion were performed to gather the required data. The obtained data were statistically analyzed by using Statistical Package for Social Science (SPSS) software. Mann-Whitney U and Kruskal-Wallis test were performed for mean comparison. The findings revealed that the household level coir yarn industry is dominated by the female workers and it was identified that fewer numbers of workers have engaged in this industry as the main occupation. In addition to that, elderly participation in the industry is higher than the younger participation and most of them have engaged in the industry as a source of extra income. Level of education, the methods of engagement, satisfaction, engagement in the industry by the next generation, support from the government, method of government support, working hours per day, employed as a main job, number of completed units per day, suffering from job related diseases and type of the diseases were related with income level of household level coir yarn laboures. The recommendations as to flourish in future includes, technological transformation for coir yarn production, strengthening the raw material base and regulating the raw material supply, introduction of new technologies, markets and training programmes, the establishment of the labourers’ association, the initiation of micro credit schemes and better consideration about the job oriented diseases.

Keywords: coir yarn, determinants, income, Sri Lanka

Procedia PDF Downloads 289

Authors: Kiyanoush Ghalavand

Abstract:

Aquaculture production is inherently a risky business, and farmers face a variety of weather, pest, disease, inptut supply, and market related risks. There are many factors out farmers control and unpredictable. Insurance has an important role in aquaculture production and is a tool to support farmers against threats. Investigation of factors affecting aquaculture farmers' adoption of aquaculture insurance strategy was the objective of this study. The purpose of this study was determining the related factors to adoption of insurance by aquaculture farmers in Khuzestan province, Iran. The research design was a descriptive and correlation surveying method. Aquaculture farmers in Khuzestan province were the target population for this study. A random sample of aquaculture selected (N=1830, n =139). The main result of the study reveled that exist correlation between the level of education, knowledge about purpose of insurance, participation in extension course, visit with insurance organization, and contact with extension agents to the adoption of insurance by aquaculture farmers were significantly positive. By using Bartlett's test and KMO test, determine whether research variables are appropriate for factor analysis (Sig = 0.000, Bartlett test = 0.9724, KMO = 0.74). The number of factors was determined using a split plot, eigenvalue, and percent of variance. An examination of the items and their factors loadings was used to understand the nature of the nine factors. To reduce subjectivity, items with factor loading equal to or greater than 0.5 were considered most important when factors were labeled. The nine factors were labeled (1) Extension and education activities, (2) Economical characteristics, (3) Governmental support, (4) communicational channel, (5) local leaders, (6) Facilitate in given damage (7) Motivation establishing, (8) Given damage in appropriate methods and (9) Appropriate activities by insurance organization. The results obtained from the factors analysis reveal that the nine factors explain percentage75 of the variation of the adoption of insurance of the adoption of insurance by aquaculture farmers in Khuzestan province.

Keywords: aquaculture farmers, insurance, factorial analysis, Khuzestan province, risks

Procedia PDF Downloads 135

Authors: Medine Demir, Volker John

Abstract:

Fluid equations in a rotating frame of reference have a broad class of important applications in meteorology and oceanography, especially in the large-scale flows considered in ocean and atmosphere, as well as many physical and industrial applications. The Coriolis and the centripetal forces, resulting from the rotation of the earth, play a crucial role in such systems. For such applications it may be required to solve the system in complex three-dimensional geometries. In recent years, the Navier--Stokes equations in a rotating frame have been investigated in a number of papers using the classical inf-sup stable mixed methods, like Taylor-Hood pairs, to contribute to the analysis and the accurate and efficient numerical simulation. Numerical analysis reveals that these classical methods introduce a pressure-dependent contribution in the velocity error bounds that is proportional to some inverse power of the viscosity. Hence, these methods are optimally convergent but small velocity errors might not be achieved for complicated pressures and small viscosity coefficients. Several approaches have been proposed for improving the pressure-robustness of pairs of finite element spaces. In this contribution, a pressure-robust space discretization of the incompressible Navier--Stokes equations in a rotating frame of reference is considered. The discretization employs divergence-free, $H^1$-conforming mixed finite element methods like Scott--Vogelius pairs. However, this approach might come with a modification of the meshes, like the use of barycentric-refined grids in case of Scott--Vogelius pairs. However, this strategy requires the finite element code to have control on the mesh generator which is not realistic in many engineering applications and might also be in conflict with the solver for the linear system. An error estimate for the velocity is derived that tracks the dependency of the error bound on the coefficients of the problem, in particular on the angular velocity. Numerical examples illustrate the theoretical results. The idea of pressure-robust method could be cast on different types of flow problems which would be considered as future studies. As another future research direction, to avoid a modification of the mesh, one may use a very simple parameter-dependent modification of the Scott-Vogelius element, the pressure-wired Stokes element, such that the inf-sup constant is independent of nearly-singular vertices.

Keywords: navier-stokes equations in a rotating frame of refence, coriolis force, pressure-robust error estimate, scott-vogelius pairs of finite element spaces

Procedia PDF Downloads 39

Authors: P. Kanakasabapathy, S. Radhika

Abstract:

In the competitive electricity market environment, the profit of the pumped-storage plant in the energy market can be maximized by operating it as a generator, when market clearing price is high and as a pump, to pump water from lower reservoir to upper reservoir, when the price is low. An optimal self-scheduling plan has been developed for a pumped-storage plant, carried out on weekly basis in order to maximize the profit of the plant, keeping into account of all the major uncertainties such as the sudden ancillary service delivery request and the price forecasting errors. For a pumped storage power plant to operate in a real time market successive self-scheduling has to be done by considering the forecast of the day-ahead market and the modified reservoir storage due to the ancillary service request of the previous day. Sliding Window Technique has been used for successive self-scheduling to ensure profit for the plant.

Keywords: ancillary services, BPSO, power system economics, self-scheduling, sliding window technique

Procedia PDF Downloads 387

Authors: Vandana N. Purav

Abstract:

The Dynamical systems concept is a mathematical formalization for any fixed rule that describes the time dependence of a points position in its ambient space. e.g. pendulum of a clock, the number of fish each spring in a lake, the number of rabbits spring in an enclosure, etc. The Dynamical system theory used to describe the complex nature that is dynamical systems with differential equations called continuous dynamical system or dynamical system with difference equations called discrete dynamical system. The concept of dynamical system has its origin in Newtonian mechanics.

Keywords: dynamical systems, Fibonacci numbers, Newtonian mechanics, discrete dynamical system

Procedia PDF Downloads 472

Authors: Sherif Keddis, Rafik Mitry, Norbert Schwesinger

Abstract:

Intelligent networking of devices has rapidly been gaining importance over the past years and with recent advances in the fields of microcontrollers, integrated circuits and wireless communication, low power applications have emerged, enabling this trend even more. Connected devices provide a much larger database thus enabling highly intelligent and accurate systems. Ensuring safe drinking water is one of the fields that require constant monitoring and can benefit from an increased accuracy. Monitoring is mainly achieved either through complex measures, such as collecting samples from the points of use, or through metering systems typically distant to the points of use which deliver less accurate assessments of the quality of water. Constant metering near the points of use is complicated due to their inaccessibility; e.g. buried water pipes, locked spaces, which makes system maintenance extremely difficult and often unviable. The research presented here attempts to overcome this challenge by providing these systems with enough energy through a flow harvester inside the pipe thus eliminating the maintenance requirements in terms of battery replacements or containment of leakage resulting from wiring such systems. The proposed flow harvester exploits the piezoelectric properties of polyvinylidene difluoride (PVDF) films to convert turbulence induced oscillations into electrical energy. It is intended to be used in standard water pipes with diameters between 0.5 and 1 inch. The working principle of the harvester uses a ring shaped bluff body inside the pipe to induce pressure fluctuations. Additionally the bluff body houses electronic components such as storage, circuitry and RF-unit. Placing the piezoelectric films downstream of that bluff body causes their oscillation which generates electrical charge. The PVDF-film is placed as a multilayered wrap fixed to the pipe wall leaving the top part to oscillate freely inside the flow. The warp, which allows for a larger active, consists of two layers of 30µm thick and 12mm wide PVDF layered alternately with two centered 6µm thick and 8mm wide aluminum foil electrodes. The length of the layers depends on the number of windings and is part of the investigation. Sealing the harvester against liquid penetration is achieved by wrapping it in a ring-shaped LDPE-film and welding the open ends. The fabrication of the PVDF-wraps is done by hand. After validating the working principle using a wind tunnel, experiments have been conducted in water, placing the harvester inside a 1 inch pipe at water velocities of 0.74m/s. To find a suitable placement of the wrap inside the pipe, two forms of fixation were compared regarding their power output. Further investigations regarding the number of windings required for efficient transduction were made. Best results were achieved using a wrap with 3 windings of the active layers which delivers a constant power output of 0.53µW at a 2.3MΩ load and an effective voltage of 1.1V. Considering the extremely low power requirements of sensor applications, these initial results are promising. For further investigations and optimization, machine designs are currently being developed to automate the fabrication and decrease tolerance of the prototypes.

Keywords: maintenance-free sensors, measurements at point of use, piezoelectric flow harvesting, universal micro generator, wireless metering systems

Procedia PDF Downloads 174

Authors: Shubham Gogri, Lucia Florescu

Abstract:

Medical diagnosis and radiotherapy treatment planning using Computed Tomography (CT) rely on the quantitative accuracy and quality of the CT images. At the same time, requirements for CT imaging include reducing the radiation dose exposure to patients and minimizing scanning time. A solution to this is the sparse-view CT technique, based on a reduced number of projection views. This, however, introduces a new problem— the incomplete projection data results in lower quality of the reconstructed images. To tackle this issue, deep learning methods have been applied to enhance the quality of the sparse-view CT images. A first approach involved employing Mir-Net, a dedicated deep neural network designed for image enhancement. This showed promise, utilizing an intricate architecture comprising encoder and decoder networks, along with the incorporation of the Charbonnier Loss. However, this approach was computationally demanding. Subsequently, a specialized Generative Adversarial Network (GAN) architecture, rooted in the Pix2Pix framework, was implemented. This GAN framework involves a U-Net-based Generator and a Discriminator based on Convolutional Neural Networks. To bolster the GAN's performance, both Charbonnier and Wasserstein loss functions were introduced, collectively focusing on capturing minute details while ensuring training stability. The integration of the perceptual loss, calculated based on feature vectors extracted from the VGG16 network pretrained on the ImageNet dataset, further enhanced the network's ability to synthesize relevant images. A series of comprehensive experiments with clinical CT data were conducted, exploring various GAN loss functions, including Wasserstein, Charbonnier, and perceptual loss. The outcomes demonstrated significant image quality improvements, confirmed through pertinent metrics such as Peak Signal-to-Noise Ratio (PSNR) and Structural Similarity Index (SSIM) between the corrected images and the ground truth. Furthermore, learning curves and qualitative comparisons added evidence of the enhanced image quality and the network's increased stability, while preserving pixel value intensity. The experiments underscored the potential of deep learning frameworks in enhancing the visual interpretation of CT scans, achieving outcomes with SSIM values close to one and PSNR values reaching up to 76.

Keywords: generative adversarial networks, sparse view computed tomography, CT image correction, Mir-Net

Procedia PDF Downloads 129

Authors: William Wong, Zakaria Alomari, Hon Ching Lai, Zhida Li

Abstract:

Modern-day information security depends on implementing Diffie-Hellman, which requires the generation of prime numbers. Because the number of primes is infinite, it is impractical to store prime numbers for use, and therefore, primality tests are indispensable in modern-day information security. A primality test is a test to determine whether a number is prime or composite. There are two types of primality tests, which are deterministic tests and probabilistic tests. Deterministic tests are adopting algorithms that provide a definite answer whether a given number is prime or composite. While in probabilistic tests, a probabilistic result would be provided, there is a degree of uncertainty. In this paper, we review three probabilistic tests: the Fermat Primality Test, the Miller-Rabin Test, and the Baillie-PSW Test, as well as one deterministic test, the Agrawal-Kayal-Saxena (AKS) Test. Furthermore, we do an analysis of these tests. All of the reviews discussed are not based on the Elliptic Curve. The analysis demonstrates that, in the majority of real-world scenarios, the Baillie- PSW test’s favorability stems from its typical operational complexity of O(log 3n) and its capacity to deliver accurate results for numbers below 2^64.

Keywords: primality tests, Fermat’s primality test, Miller-Rabin primality test, Baillie-PSW primality test, AKS primality test

Procedia PDF Downloads 63

Authors: Sadeeq Launi

Abstract:

NGOs, the world over, have been recognized as part of the institutions that complement government activities in providing services to the people, particularly in respect of human development. This study examined the role played by the NGOs in human development in Bauchi State, Nigeria, between 2004 and 2013. The emphasis was on reproductive health and access to education role of the selected NGOs. All the research questions, objectives and hypotheses were stated in line with these variables. The theoretical framework that guided the study was the participatory development approach. Being a survey research, data were generated from both primary and secondary sources with questionnaires and interviews as the instruments for generating the primary data. The population of the study was made up of the staff of the selected NGOs, beneficiaries, health staff and school teachers in Bauchi State. The sample drawn from these categories were 90, 107 and 148 units respectively. Stratified random and simple random sampling techniques were adopted for NGOs staff, and Health staff and school teachers data were analyzed quantitatively and qualitatively and hypotheses were tested using Pearson Chi-square test through SPSS computer statistical package. The study revealed that despite the challenges facing NGOs operations in the study area, NGOs rendered services in the areas of health and education This research recommends among others that, both government and people should be more cooperative to NGOs to enable them provide more efficient and effective services. Governments at all levels should be more dedicated to increasing accessibility and affordability of basic education and reproductive health care facilities and services in Bauchi state through committing more resources to the Health and Education sectors, this would support and facilitate the complementary role of NGOs in providing teaching facilities, drugs, and other reproductive health services in the States. More enlightenment campaigns should be carried out by governments to sensitize the public, particularly women on the need to embrace immunization programmes for their children and antenatal care services being provided by both the government and NGOs.

Keywords: access to education, human development, NGOs, reproductive health

Procedia PDF Downloads 159

Authors: Sajjad Ali Khan Sajjad Ali Khan, Gohar Ayub, Khalil Ur Rahman, Muhammad Sajid, Mumtaz Farooq, Mohammad Irshad, Haider Ali

Abstract:

A trail was carried out to know the effect of different soil media and planting time on the cuttings of cherry (Prunus avium L.) rootstock Colt at Agriculture Research Institute (ARI) Mingora swat, during winter 2011. The experiment was laid out in Randomized Complete Block Design (RCBD) with split plot arrangement and was replicated three times. Soil media (Silt, Garden soil and Silt+Garden soil+FYM) were assigned to main plots whereas, planting Dates (1st Jan, 11th Jan, 21st Jan, 1st Feb, 11th Feb, 21st Feb and 2nd March) subjected to sub plots. The data recorded on sprouting percentage, shoot diameter cutting-1, number of leaves cutting-1, rootstock height (cm), survival percentage, number of roots, root length (cm), root volume (cm3) and root weight (gm) were significantly affected by different soil media. Maximum sprouting percentage (100%), shoot diameter (1.72 mm), number of leaves cutting-1 (76.74), rootstock height (104.36 cm), survival percentage (41.67%), number of roots (76.35), root length (11.28 cm), root volume (4.43 cm3) and root weight (4.64 gm) were recorded in media M3 (Garden soil+silt+FYM). A significant response to various planting dates were observed for most of vegetative and rooting attributes of cherry rootstock Colt. 1st January plantation showed maximum sprouting percentage (100%), shoot diameter (1.99 mm), number of leaves (81.46), rootstock height (126.24 cm), survival percentage (58.12%), whereas 11th January plantation showed more number of roots (94.43), root length (10.60 cm), root volume (3.68 cm3) and root weight (3.71 gm). Based on the results from the experimental work, it is recommended that cherry cuttings should be planted in early January in soil media (Silt+Garden soil+ FYM) for better growth and development under the agro climatic conditions of temperate region.

Keywords: soil media, cherry rootstock, planting dates, growth parameters

Procedia PDF Downloads 80