Search results for: test unit

Authors: Kiurski S. Jelena, Oros B. Ivana, Kecić S. Vesna, Kovačević M. Ilija, Aksentijević M. Snežana

Abstract:

The adsorption efficiency of various adsorbents for the removal of Zn(II) ions from the waste printing developer was studied in laboratory batch mode. The maximum adsorption efficiency of 94.1% was achieved with unfired clay pellets size (d≈15 mm). The obtained values of adsorption efficiency was subjected to the independent samples t-test in order to investigate the statistically significant differences of the investigated adsorbents for the effective removal of Zn(II) ions from the waste printing developer. The most statistically significant differences of adsorption efficiencies for Zn(II) ions removal were obtained between unfired clay pellets size (d≈15 mm) and activated carbon (|t|= 6.909), natural zeolite (|t|= 10.380), mixture of activated carbon and natural zeolite (|t|= 9.865), bentonite (|t|= 6.159), fired clay (|t|= 6.641), fired clay pellets size (d≈5 mm) (|t|= 6.678), fired clay pellets size (d≈8 mm) (|t|= 3.422), respectively.

Keywords: Adsorption efficiency, adsorbent, statistical analysis, zinc ion.

Procedia PDF Downloads 389

Authors: Suparna Bharadwaj, Sriganesh Kamath, Gopalakrishna K. N., Subhas Konar

Abstract:

Introduction: Post-operative cognitive dysfunction (POCD) is a spectrum of clinical syndrome presenting as emergence delirium (ED) and/or post-operative delirium (POD). ED is a transient state (minutes to hours) of marked agitation after the discontinuation of general anesthesia, which does not respond to consoling measures. On the other hand, POD without identifiable etiology is not temporally related to emergence from anesthesia. These patients often emerge smoothly and may be lucid in the post-anesthesia care unit (PACU), but may develop fluctuating mental status, most commonly between postoperative days one and three. General anesthesia (GA) has been identified as a risk factor for POCD. Cranial surgeries involve brain handling in addition to exposure to GA. We hypothesize that the incidence of postoperative delirium after cranial surgery is twice that of spinal surgery. The primary objective of this study was to evaluate the incidence of emergence delirium and postoperative delirium in patients undergoing cranial and spinal neurosurgeries. The secondary objective was to identify the perioperative risk factors of ED and POD. Methods: This was a prospective cohort observation study conducted from March 2020 to September 2023 conducted at a tertiary neurocentre. After obtaining institutional ethics committee approval, adult patients undergoing cranial or spinal surgery with a Glasgow coma scale of 15 were included in the study. Patients undergoing cranial surgery are considered exposed to risk factors, while patients undergoing spinal surgery are considered unexposed. All study subjects received standard general anesthesia. About twenty perioperative parameters were identified as risk factors for POCD. ED was assessed using the Riker sedation agitation scale, and POD was assessed using the confusion assessment method. A sample size of 2000 patients was planned with 1000 each cranial and spinal cases. However, around 700 spinal patients could be recruited for this study. Results: In this study, about two thousand patients were screened for inclusion. However, 1185 cranial cases and 742 spinal cases were considered for final analysis. Both the groups were similar in terms of demographics. Incidence of ED was 25.8% after cranial surgery vs 10.24% after spinal surgery (relative risk 2.5). The incidence of POD after cranial surgery is 20.25% vs 2.15% after cranial surgery (relative risk 9.3). All the proposed risk factors were assessed using binomial logistic regression. Conclusion: Cranial cases expose patients to a nine times higher risk for the development of postoperative delirium. The presence of ED predisposes to POD representing a spectrum.

Keywords: post operative cognitive dysfunction, Neurosurgical patients cohort study, cohort study, emergence delirium

Procedia PDF Downloads 0

Authors: Ahmad Zaini, F. Muhammad Reza Hadafi, Surya Sumpeno, Muhtadin, Mochamad Hariadi

Abstract:

The lack of information about museum’s collection reduces the number of visits of museum. Museum’s revitalization is an urgent activity to increase the number of visits. The research's roadmap is building a web-based application that visualizes museum in the virtual form including museum's statue reconstruction in the form of 3D. This paper describes implementation of three-dimensional model reconstruction method based on light-strip pattern on the museum statue using 3D scanner. Noise removal, alignment, meshing and refinement model's processes is implemented to get a better 3D object reconstruction. Model’s texture derives from surface texture mapping between object's images with reconstructed 3D model. Accuracy test of dimension of the model is measured by calculating relative error of virtual model dimension compared against the original object. The result is realistic three-dimensional model textured with relative error around 4.3% to 5.8%.

Keywords: 3D reconstruction, light pattern structure, texture mapping, museum

Procedia PDF Downloads 467

Authors: Carolina Senabre Blanes, Sergio Valero Verdú, Emilio Velasco SáNchez

Abstract:

This research objective is to obtain a percentage of success for each Ministry of Transport (MOT) facilities of each city of the Alicante region from Comunidad Valenciana from Spain by comparing results obtained by using different brake testers. It has been studied which types of brake tester are being used at each city nowadays. Different types of brake testers are used at each city, and the mechanical engineering staffs from the Miguel Hernández University have studied differences between all of them, and have obtained measures from each type. A percentage of probability of success will be given to each MOT station when you try to pass the exam with the same car with same characteristics and the same wheels. In other words, parameters of the vehicle have been controlled to be the same at all tests; therefore, brake measurements variability will be due to the type of testers could be used at the MOT station. A percentage of probability to pass the brake exam at each city will be given by comparing results of tests.

Keywords: brake tester, Mot station, probability to pass the exam, brake tester characteristics

Procedia PDF Downloads 293

Authors: Raveena Naz

Abstract:

The concept of ‘Corporate Social Responsibility’ (CSR) has often relied on firms thinking beyond their economic interest despite the larger debate of shareholder versus stakeholder interest. India gave legal recognition to CSR in the Companies Act, 2013 which promises better corporate governance. CSR in India is believed to be different for two reasons: the dominance of family business and the history of practice of social responsibility as a form of philanthropy (mainly among the family business). This paper problematises the actual structure of business houses in India and the role of CSR in India. When the law identifies each company as a separate business entity, the economics of institutions emphasizes the ‘business group’ consisting of a plethora of firms as the institutional organization of business. The capital owned or controlled by the family group is spread across the firms through the interholding (interlocked holding) structures. This creates peculiar implications for CSR legislation in India. The legislation sets criteria for individual firms to undertake liability of mandatory CSR if they are above a certain threshold. Within this framework, the largest family firms which are all part of family owned business groups top the CSR expenditure list. The interholding structures, common managers, auditors and series of related party transactions among these firms help the family to run the business as a ‘family business’ even when the shares are issued to the public. This kind of governance structure allows family owned business group to show mandatory compliance of CSR even when they actually spend much less than what is prescribed by law. This aspect of the family firms is not addressed by the CSR legislation in particular or corporate governance legislation in general in India. The paper illustrates this with an empirical study of one of the largest family owned business group in India which is well acclaimed for its CSR activities. The individual companies under the business group are identified, shareholding patterns explored, related party transactions investigated, common managing authorities are identified; and assets, liabilities and profit/loss accounting practices are analysed. The data has been mainly collected from mandatory disclosures in the annual reports and financial statements of the companies within the business group accessed from the official website of the ultimate controlling authority. The paper demonstrates how the business group through these series of shareholding network reduces its legally mandated CSR liability. The paper thus indicates the inadequacy of CSR legislation in India because the unit of compliance is an individual firm and it assumes that each firm is independent and only connected to each other through market dealings. The law does not recognize the inter-connections of firms in corporate governance structures of family owned business group and hence is inadequate in its design to effect the threshold level of CSR expenditure. This is the central argument of the paper.

Keywords: business group, corporate governance, corporate social responsibility, family firm

Procedia PDF Downloads 280

Authors: Genaro Bolívar, Manuel Mas, Maria Tortolero, Jorge Salazar

Abstract:

Due to the extensive use of water injection for oil displacement and pressure maintenance in oil fields, many reservoirs experience the problem of scale deposition when injection water starts to break through. In most cases the scaled-up wells are caused by the formation of sulfate and carbonate scales of calcium and strontium. Due to their relative hardness and low solubility, there are limited processes available for their removal and preventive measures such as the “squeeze” inhibitor treatment have to be taken. It is, therefore, important to gain a proper understanding of the kinetics of scale formation and its detrimental effects on formation damage under both inhibited and uninhibited conditions. Recently, the production of chitosan was started in our country and in the PDVSA-Intevep laboratories was synthesized and evaluated the properties of carboxymethyl chitosan (CMQ) as chelating agent of Ca2 + ions in water injection. In this regard, the characterization of the biopolymer by 13C - NMR, FTIR, TGA, and TM0374-2007 standard laboratory test has demonstrated the ability to remove up to 70% calcium ions in solution and shows a behavior that approaches that of commercial products.

Keywords: carboxymethyl chitosan, scale, calcium carbonate scale deposition, water injection

Procedia PDF Downloads 437

Authors: Ghada Chater, Mounir Dhouib

Abstract:

Zawiyas are mausoleums where saints called 'waly' are buried and where ritual practices of Sufi Islamic movement take place. These funerary monuments have constituted since the medieval period a fundamental component of rural and urban Islamic landscape, especially that of Tunisia.The hypothesis is that these monuments reflect in their architecture the Sufi underlying thought. The paper’s target is to verify the validity of this hypothesis and possibly show the incarnation mode of Islamic Sufi paradigm in the zawiya’s architecture. This study considers the main Zawiya of one of the most important religious brotherhoods in Tunisia, which is Kadiria. A morphological analysis has been conducted and crossed later to a spiritual hermeneutic test. The result of this confrontation was significant: the paradigmatic element of the zawiya, materialized by the esoteric / exoteric dome 'kubba', returns in its geometry and structure to one of the Sufism key concepts: the unity of the creative spirit in the diversity and plurality of evanescent bodies. Thus, the creative act finds its reflection not only in the spirit of the perfect human microcosm (the waly microcosm), but also within the building dedicated to him.

Keywords: architecture, Islam, Sufism, waly, zawiya

Procedia PDF Downloads 348

Authors: Yasir Khan

Abstract:

The continued growth in international students coming to China for higher education had a significant positive impact on trade and GDP in China. Student mobility may expend trade with their country of origin, owing to superior knowledge, or preferential access to market opportunities. We test this hypothesis using Chinese trade data from 1999 to 2017. In fully-modify (OLS) and dynamic (OLS) testing estimation, we find that a 1.24 percent increase in student inward mobility is associated with a 1 percent increase in Chinese export trade. On the other hand, we find that a 1.18 percent increase in the student inward mobility to China is associated with a 1 percent increase in import trade. In addition, we find that a 1.13 percent increase in international student inward mobility is associated with a 1 percent increase in the GDP. The outcome suggests that international students have a strong influence on Gross Domestic Product (GDP), exports and imports trade. However, the study holds that the government should attach great attachment and importance to the role of international students in the export and import trade.

Keywords: international student mobility, China, export, import, GDP, FMOLS, DOLS

Procedia PDF Downloads 219

Authors: G. O. Fakunmoju, F. A. Fakunmoju

Abstract:

The experiment was conducted to evaluate the growth response of African giant catfish (Clarias gariepinus) fed with varying levels of Galawaste based diet, 300 clarias gariepinus fingerlings with mean body weight 10 ± 0.1g were assigned to five (treatment levels in which Gala waste meal replaced maize at 0, 25, 50, 75, 100% respectively in a completely randomized design. The trial fish were fed at 5% body weight daily for a period of 84 days. Data collected showed that body weight gain increased with an increase gala waste meal in the diet (P<0.05). The similar observation was recorded for feed intake but there was no significant (P>0.05) difference in feed conversion ratio among the treatments. All the fish fed the test ingredients performed better than the control groups hence, Gala waste meal could be recommended as a dietary supplement in the diet of African Giant Catfish.

Keywords: Galawaste meal, Clarias gariepinus, replacement, growth performance, diets

Procedia PDF Downloads 405

Authors: Rukaiya Suleiman Umar, Annah Kwadu Medugu

Abstract:

Moringa oleifera is mainly used as herbal medicine in most homes in Northern Nigeria. The plant is easy to grow and thrives very well regardless the type of soil. Use of moringa leaves in food production can yield attractive varieties on menu. This paper evaluates the acceptability of dishes produced with fresh moringa leaves with a view to promoting it in popular restaurants. A three course menu consisting of cream of moringa soup as the starter, mixed meat moringa sauce with semovita as the main dish and moringa roll as sweet was produced and served to a 60-member taste panel made of three groups of 20 each. Respondents were asked to rate the organoleptic qualities of the samples on a 10-point bipolar scale ranging from 1 (Dislike extremely) – 10 (Like extremely). Data collected were treated to one sample t-test and One Way ANOVA. Results show that the panelists extremely like the moringa products. It is recommended that Moringa oleifera should be incorporated into meals which is more readily acceptable than medicine.

Keywords: Moringa oleifera, food production, menu planning, healthy living

Procedia PDF Downloads 282

Authors: Svetlana Trifonova Djambova, Natalia Bobeva Ivanova, Roumiana Asenova Zaharieva

Abstract:

Small size acoustic chamber test method has been applied to experimentally evaluate and compare the airborne sound insulation provided by plasterboard sandwich panels filled with mineral wool and with its alternative from recycled textile material (produced by two different technologies). A sound source room is used as an original small-size acoustic chamber, specially built in a real-size room, utilized as a sound receiving room. The experimental results of one of the recycled textile material specimens have demonstrated sound insulation properties similar to those of the mineral wool specimen and even superior in the 1600-3150 Hz frequency range. This study contributes to the improvement of recycled textile material production, as well as to the synergy of heat insulation and sound insulation performances of building materials.

Keywords: airborne sound insulation, heat insulation products, mineral wool, recycled textile material

Procedia PDF Downloads 190

Authors: Denisa Mackova, Andrea Pokorna

Abstract:

The management of postoperative pain is a meaningful part of quality care. The experience and knowledge of registered nurses in postoperative pain management can be influenced by local know-how. Therefore, the research helps to understand the cultural differences between two countries with the aim of evaluating the management of postoperative pain management among the nurses from the Czech Republic and the Kingdom of Saudi Arabia. Both countries have different procedures on managing postoperative pain and the research will provide an understanding of both the advantages and disadvantages of the procedures and also highlight the knowledge and experience of registered nurses in both countries. Between the Czech Republic and the Kingdom of Saudi Arabia, the expectation is for differing results in the usage of opioid analgesia for the patients postoperatively and in the experience of registered nurses with Patient Controlled Analgesia. The aim is to evaluate the knowledge and awareness of registered nurses and to merge the data with the postoperative pain management in the early postoperative period in the Czech Republic and the Kingdom of Saudi Arabia. Also, the aim is to assess the knowledge and experience of registered nurses by using Patient Controlled Analgesia and epidural analgesia treatment in the early postoperative period. The criteria for those providing input into the study, are registered nurses, working in surgical settings (standard departments, post-anesthesia care unit, day care surgery or ICU’s) caring for patients in the postoperative period. Method: Research is being conducted by questionnaires. It is a quantitative research, a comparative study of registered nurses in the Czech Republic and the Kingdom of Saudi Arabia. Questionnaire surveys were distributed through an electronic Bristol online survey. Results: The collection of the data in the Kingdom of Saudi Arabia has been completed successfully, with 550 respondents, 77 were excluded and 473 respondents were included for statistical data analysis. The outcome of the research is expected to highlight the differences in treatment through Patient Controlled Analgesia, with more frequent use in the Kingdom of Saudi Arabia. A similar assumption is expected for treatment conducted by analgesia. We predict that opioids will be used more regularly in the Kingdom of Saudi Arabia, whilst therapy through NSAID’s being the most common approach in the Czech Republic. Discussion/Conclusion: The majority of respondents from the Kingdom of Saudi Arabia were female registered nurses from a multitude of nations. We are expecting a similar split in gender between the Czech Republic respondents; however, there will be a smaller number of nationalities. Relevance for research and practice: Output from the research will assess the knowledge, experience and practice of patient controlled analgesia and epidural analgesia treatment. Acknowledgement: This research was accepted and affiliated to the project: Postoperative pain management, knowledge and experience registered nurses (Czech Republic and Kingdom of Saudi Arabia) – SGS05/2019-2020.

Keywords: acute postoperative pain, epidural analgesia, nursing care, patient controlled analgesia

Procedia PDF Downloads 180

Authors: K. C. M. Wong, C. P. Y. Cheng, K. Y. Chan, G. S. C. Fung, T. F. O. Lau, K. F. C. Leung, J. P. C. Fok

Abstract:

Hospital Authority (HA) is the statutory body to manage all public hospitals in Hong Kong. Occupational Care Medicine Service (OMCS) is an in-house multi-disciplinary team responsible for injury management in HA. Hospital administrative services (AS) provides essential support in hospital daily operation to facilitate the provision of quality healthcare services. An occupational health enhancement program in Tai Po Hospital (TPH) domestic service supporting unit (DSSU) was piloted in 2013 with satisfactory outcome, the keys to success were staff engagement and management support. Riding on the success, the program was rolled out to another 5 AS departments of Alice Ho Miu Ling Nethersole Hospital (AHNH) and TPH in 2015. This paper highlights the indispensable components of disability management and occupational health enhancement program in hospital settings. Objectives: 1) Facilitate workplace to support staff with health affecting work problem, 2) Enhance staff’s occupational health. Methodology: Hospital Occupational Safety and Health (OSH) team and AS departments (catering, linen services, and DSSU) of AHNH and TPH worked closely with OMCS. Focus group meetings and worksite visits were conducted with frontline staff engagement. OSH hazards were identified with corresponding OSH improvement measures introduced, e.g., invention of high dusting device to minimize working at height; tailor-made linen cart to minimize back bending at work, etc. Specific MHO trainings were offered to each AS department. A disability management workshop was provided to supervisors in order to enhance their knowledge and skills in return-to-work (RTW) facilitation. Based on injured staff's health condition, OMCS would provide work recommendation, and RTW plan was formulated with engagement of staff and their supervisors. Genuine communication among stakeholders with expectation management paved the way for realistic goals setting and success in our program. Outcome: After implementation of the program, a significant drop of 26% in musculoskeletal disorders related sickness absence day was noted in 2016 as compared to the average of 2013-2015. The improvement was postulated by innovative OSH improvement measures, teamwork, staff engagement and management support. Staff and supervisors’ feedback were very encouraging that 90% respondents rated very satisfactory in program evaluation. This program exemplified good work sharing among departments to support staff in need.

Keywords: disability management, occupational health, return to work, occupational medicine

Procedia PDF Downloads 212

Authors: Eyup Yurt, Ahmet Kurnaz, Ismail Sahin

Abstract:

The purpose of the study is to investigate the education faculty students’ attitudes towards e-learning according to different variables. In current study, the data were collected from 393 students of an education faculty in Turkey. In this study, theattitude towards e‐learning scale and the demographic information form were used to collect data. The collected data were analyzed by t-test, ANOVA and Pearson correlation coefficient. It was found that there is a significant difference in students’ tendency towards e-learning and avoidance from e-learning based on gender. Male students have more positive attitudes towards e-learning than female students. Also, the students who used the internet lesshave higher levels of avoidance from e-learning. Additionally, it is found that there is a positive and significant relationship between the number of personal mobile learning devices and tendency towards e-learning. On the other hand, there is a negative and significant relationship between the number of personal mobile learning devices and avoidance from e-learning. Also, suggestions were presented according to findings.

Keywords: education faculty students, attitude towards e-learning, gender, daily internet usage time, m-learning

Procedia PDF Downloads 308

Authors: Sarah Alamolhoda, Kevin J. Smith, Xiaotao Bi, Naoko Ellis

Abstract:

For millennials, biomass has been the most important source of fuel used to produce energy. Energy derived from biomass is renewable by re-growth of biomass. Various technologies are used to convert biomass to potential renewable products including combustion, gasification, pyrolysis and fermentation. Gasification is the incomplete combustion of biomass in a controlled environment that results in valuable products such as syngas, biooil and biochar. Syngas is a combustible gas consisting of hydrogen (H₂), carbon monoxide (CO), carbon dioxide (CO₂), and traces of methane (CH₄) and nitrogen (N₂). Cleaned syngas can be used as a turbine fuel to generate electricity, raw material for hydrogen and synthetic natural gas production, or as the anode gas of solid oxide fuel cells. In this work, syngas as a product of woody biomass gasification in British Columbia, Canada, was introduced to two consecutive fixed bed reactors to perform a catalytic water gas shift reaction followed by a catalytic methanation reaction. The water gas shift reaction is a well-established industrial process and used to increase the hydrogen content of the syngas before the methanation process. Catalysts were used in the process since both reactions are reversible exothermic, and thermodynamically preferred at lower temperatures while kinetically favored at elevated temperatures. The water gas shift reactor and the methanation reactor were packed with Cu-based catalyst and Ni-based catalyst, respectively. Simulated syngas with different percentages of CO, H₂, CH₄, and CO₂ were fed to the reactors to investigate the effect of operating conditions in the unit. The water gas shift reaction experiments were done in the temperature of 150 ˚C to 200 ˚C, and the pressure of 550 kPa to 830 kPa. Similarly, methanation experiments were run in the temperature of 300 ˚C to 400 ˚C, and the pressure of 2340 kPa to 3450 kPa. The Methanation reaction reached 98% of CO conversion at 340 ˚C and 3450 kPa, in which more than half of CO was converted to CH₄. Increasing the reaction temperature caused reduction in the CO conversion and increase in the CH₄ selectivity. The process was designed to be renewable and release low greenhouse gas emissions. Syngas is a clean burning fuel, however by going through water gas shift reaction, toxic CO was removed, and hydrogen as a green fuel was produced. Moreover, in the methanation process, the syngas energy was transformed to a fuel with higher energy density (per volume) leading to reduction in the amount of required fuel that flows through the equipment and improvement in the process efficiency. Natural gas is about 3.5 times more efficient (energy/ volume) than hydrogen and easier to store and transport. When modification of existing infrastructure is not practical, the partial conversion of renewable hydrogen to natural gas (with up to 15% hydrogen content), the efficiency would be preserved while greenhouse gas emission footprint is eliminated.

Keywords: renewable natural gas, methane, hydrogen, gasification, syngas, catalysis, fuel

Procedia PDF Downloads 118

Authors: Zainal Abu Zatim, Hafizah Omar Zaki

Abstract:

Substantial research had been done on refining employee’s customer service performance. Thus, there were very limited empirical studies that are engage in an inter-organizational climate study in assessing employee’s customer service performance. With the current economic situation as well as emerging needs and requirements, all businesses either from public or private sector serving customers put greater attention on fulfilling those needs and requirements. In this state of affairs, the act of polishing its employees’ skills, knowledge, teamwork and passion is very important in ensuring better performance deliverance. A study conducted in one of the telecommunication service provider company in Malaysia had been done to test its inter-organizational climate study. The Internal Climate Study was done to benchmark opinions and perceptions of its employees. The study had provided baseline information about perceptions that exist in the internal environment and ways forward to improve customer service performance. The approach used is through the use of focus group and qualitative interview.

Keywords: employees, Customer Service Performance, inter-organizational climate study, public and private sector

Procedia PDF Downloads 399

Authors: Tariq Aziz, Suresh Kumar, Vikesh Kumar, Sheraz Mustafa, Jhanzeb Marwat

Abstract:

The paper provides an updated version of volatility spillover among the equity markets of South Asian countries, including Pakistan, India, Srilanka, and Bangladesh. The analysis uses both symmetric and asymmetric Generalized Autoregressive Conditional Heteroscedasticity models to investigate volatility persistence and leverage effect. The bivariate EGARCH model is used to test for volatility transmission between two equity markets. Weekly data for the period February 2013 to August 2019 is used for empirical analysis. The findings indicate that the leverage effect exists in the equity markets of all the countries except Bangladesh. The volatility spillover from the equity market of Bangladesh to all other countries is negative and significant whereas the volatility of the equity market of Sri-Lanka does influence the volatility of any other country’s equity market. Indian equity market influence only the volatility of the Sri-Lankan equity market; and there is bidirectional volatility spillover between the equity markets of Pakistan and Bangladesh. The findings are important for policy-makers and international investors.

Keywords: volatility spillover, volatility persistence, garch, egarch

Procedia PDF Downloads 140

Authors: Anne C. Okwedadi, Samson Ng’ambi, Ian Jefferson

Abstract:

Collapsible soils go through radical rearrangement of their particles when triggered by water, stress or/and vibration, causing loss of volume. This loss of volume in soil as seen in foundation failures has caused millions of dollars’ worth of damages to public facilities and infrastructure and so has an adverse effect on the society and people. Despite these consequences and the several studies that are available, more research is still required in the study of soil collapsibility. Discerning the pedogenesis (formation) of soils and investigating the combined effects of the different geological soil properties is key to elucidating and quantifying soils collapsibility. This study presents a novel laboratory testing regime that would be undertaken on soil samples where the effects of soil type, compactive variables (moisture content, density, void ratio, degree of saturation) and loading are analyzed. It is anticipated that results obtained would be useful in mapping the trend of the combined effect thus the basis for evaluating soil collapsibility or collapse potentials encountered in construction with volume loss problems attributed to collapse.

Keywords: collapsible soil, geomorphological process, soil collapsibility properties, soil test

Procedia PDF Downloads 471

Authors: Niyi Adegoke, Saanumi Jimmy Omolou

Abstract:

The prevalence rate of youth involving in cybercrime is alarming, which calls for concern among the government, parents, NGO and religious bodies, hence this paper aims at examining youth involvement in cybercrime in Nigeria. Achievement motivation theory was used to explain the activities of cyber-criminals in Nigerian society. A descriptive survey method was adopted for the study. The sample for the study was one hundred and fifty (150) respondents randomly selected from the population of the study. A questionnaire was used to gather information and data from the respondents. Data collected through the questionnaire were analyzed using percentage tool for the respondents’ bio-data while chi-square was employed to test the hypotheses. Findings from the study have revealed that parental negligence, unemployment, peer influence, and quest for materialism were responsible for cyber-crimes in Nigeria. The study concludes with the following recommendations among which are: creating employment opportunities for the youths and ensure good governance and accountability among other things will go a long way to solve the problem of cybercrime in our society.

Keywords: cybercrime, youth, Nigeria, unemployment, information communication technology

Procedia PDF Downloads 228

Authors: Angsumalin Puntho

Abstract:

Disruptive technology has had a great influence on our everyday lives and the existence of an organization. Geologists in the public sector need to keep up with digital technology and be able to work and collaborate in a more effective manner. The result from SWOT and 7S McKinsey analyses suggest that there are inadequate IT personnel, no individual digital literacy development plan, and a misunderstanding of management policies. The Office of Civil Service Commission develops digital literacy skills that civil servants and government officers should possess in order to work effectively; it consists of nine dimensions, including computer skills, internet skills, cyber security awareness, word processing, spreadsheets, presentation programs, online collaboration, graphics editors and cyber security practices; and six steps of digital literacy development including self-assessment, individual development plan, self-learning, certified test, learning reflection, and practices. Geologists can use digital literacy as a learning tool to develop themselves for better career opportunities.

Keywords: disruptive technology, digital technology, digital literacy, computer skills

Procedia PDF Downloads 116

Authors: Jui-Chen Huang

Abstract:

Nowadays, the population is aging, the number of people who need to be taken care of is increased, but the manpower and funding are insufficient. Therefore, this study aims to explore the attitudes and willingness of arthritis patients to adopt telecare and to take a large medical institution in the central area of Taiwan as a sample hospital. A structured questionnaire (using the Likert five-point scale) was used to collect chronic patients over 20 years old as sample data, and a total of 500 valid questionnaires were effectively collected. The SPSS 18.0 statistical software was used for reliability analysis and independent sample t-test to explore the differences in attitudes and willingness to use telecare for arthritis patients and non-arthritic patients. The Cronbach's alpha value of this study questionnaire was above 0.94, showing good reliability. Arthritis patients and non-arthritic patients had statistically significant differences in attitudes toward telecare, while the willingness to use did not reach statistically significant differences. In addition, the average attitude and intention of arthritis patients for telecare are 3.38 and 3.41, respectively, indicating that arthritis patients have a certain degree of attitude and willingness to adopt telecare, which is worthy of follow-up research and practical industry push.

Keywords: telecare, arthritis patients, attitudes, intention

Procedia PDF Downloads 142

Authors: M. Celeska, K. Najdenkoski, V. Dimchev, V. Stoilkov

Abstract:

Accurate determination of wind turbine performance is necessary for economic operation of a wind farm. At present, the procedure to carry out the power performance verification of wind turbines is based on a standard of the International Electrotechnical Commission (IEC). In this paper, nonparametric statistical inference is applied to designing a simple, inexpensive method of verifying the power performance of a wind turbine. A statistical test is explained, examined, and the adequacy is tested over real data. The methods use the information that is collected by the SCADA system (Supervisory Control and Data Acquisition) from the sensors embedded in the wind turbines in order to carry out the power performance verification of a wind farm. The study has used data on the monthly output of wind farm in the Republic of Macedonia, and the time measuring interval was from January 1, 2016, to December 31, 2016. At the end, it is concluded whether the power performance of a wind turbine differed significantly from what would be expected. The results of the implementation of the proposed methods showed that the power performance of the specific wind farm under assessment was acceptable.

Keywords: canonical correlation analysis, power curve, power performance, wind energy

Procedia PDF Downloads 336

Authors: Peter Ugbedeojo Nelson

Abstract:

Despite the tremendous advancements and knowledge acquisition around entrepreneurship orientation (EO) research, there may still be more to learn on how environmental dynamics would permute organizational processes and determine the extent to which success would be achieved. Using the contingency theory, we test a model that proposes a moderating influence of external relational capital and environmental hostility on the EO-performance effect of 423 managers/owners of small and medium scale enterprises. The hypotheses were tested using Hayes simultaneous regression, and the results showed that all EO dimensions (risk-taking, innovation, and performance) had a main effect on performance while the moderating variables interacted well with risk-taking (more than other EO dimensions) to improve performance. However, external relational capital, more than environmental hostility, influences the EO-performance relationship. Our findings highlight the differential ways that EO dimensions interact with environmental contingencies to influence performance. Further studies can examine how competitive aggressiveness and autonomy are moderated by external relational capital and environmental hostility.

Keywords: external relational capital, entrepreneurial orientation, risk-taking, innovation, proactiveness

Procedia PDF Downloads 56

Authors: Mina Mortazavi, Hamid Ronagh, Pezhman Sharafi

Abstract:

The new concept of a cold formed-hot rolled hybrid steel wall panel system is introduced to overcome the deficiency in lateral load resisting capacity of cold-formed steel structures. The hybrid system is composed of a cold-formed steel part laterally connected to hot rolled part. The hot rolled steel part is responsible for carrying the whole lateral load; while the cold formed steel part is only required to transfer the lateral load to the hot rolled part without any local failure. The vertical load is beared by both hot rolled, and cold formed steel part, proportionally. In order to investigate the lateral performance of the proposed system, it should be tested under simultaneous lateral and vertical load. The main concern is to deliver the loads to each part during the test to simulate the real load distribution in the structure. In this paper, a detailed description of the proposed wall panel system and the designed testing rig is provided.

Keywords: cold-formed steel, hybrid system, wall panel system, testing rig design

Procedia PDF Downloads 423

Authors: Bai Zhiwei, Zhang Shuxia

Abstract:

By sealing constraint, the system of nuclear fuel production penetrates a trace of air in during its service. The vapor in the air can react with material in the system and generate solid uranium compounds. These solid uranium compounds continue to accumulate and attached to the production equipment and pipeline of system, which not only affects the operation reliability of production equipment and give off radiation hazard as well after system retired. Therefore, it is necessary to select a reasonable method to remove it. Through the analysis of physicochemical properties of solid uranium compounds, halogenated fluoride compounds are selected as a cleaning agent, which can remove solid uranium compounds effectively. This paper studied the related chemical reaction under the condition of static test and results show that the selection of high fluoride halogen compounds can be removed solid uranium compounds completely. The study on the influence of reaction pressure with the reaction rate discovered a phenomenon that the higher the pressure, the faster the reaction rate.

Keywords: fluoride halogen compound, remove, radiation, solid uranium compound

Procedia PDF Downloads 302

Authors: A. Hassoune, M. Khafallah, A. Mesbahi, T. Bouragba

Abstract:

This work presents an improved strategy of control for charging a lithium-ion battery in an electric vehicle charging station using two charger topologies i.e. single ended primary inductor converter (SEPIC) and forward converter. In terms of rapidity and accuracy, the power system consists of a topology/control diagram that would overcome the performance constraints, for instance the power instability, the battery overloading and how the energy conversion blocks would react efficiently to any kind of perturbations. Simulation results show the effectiveness of the proposed topologies operated with a power management algorithm based on voltage/peak current mode controls. In order to provide credible findings, a low power prototype is developed to test the control strategy via experimental evaluations of the converter topology and its controls.

Keywords: battery storage buffer, charging station, electric vehicle, experimental analysis, management algorithm, switches control

Procedia PDF Downloads 165

Authors: Virgilio Angelo Gelera Gener

Abstract:

This study investigates the role of short-term accommodations on the place brand and real estate development of urban areas. It aims to know the perceptions of the general public, real estate developers, as well as city and barangay-level local government units (LGUs) on how these lodgings affect the place brand and land value of a community. It likewise attempts to identify the personal and institutional variables having a great influence on said perceptions in order to provide a better understanding of these establishments and their relevance within urban localities. Using certain sources, Malate, Manila was identified to be the ideal study area of the thesis. This prompted the employment of mixed methods research as the study’s fundamental data gathering and analytical tool. Here, a survey with 350 locals was done, asking them questions that would answer the aforementioned queries. Thereafter, a Pearson Chi-square Test and Multinomial Logistic Regression (MLR) were utilized to determine the variables affecting their perceptions. There were also Focus Group Discussions (FGDs) with the three (3) most populated Malate barangays, as well as Key Informant Interviews (KIIs) with selected city officials and fifteen (15) real estate company representatives. With that, survey results showed that although a 1992 Department of Tourism (DOT) Circular regards short-term accommodations as lodgings mainly for travelers, most people actually use it for their private/intimate moments. Because of this, the survey further revealed that short-term accommodations exhibit a negative place brand among the respondents though they also believe that it’s still one of society’s most important economic players. Statistics from the Pearson Chi-square Test, on the other hand, indicate that there are fourteen (14) out of seventeen (17) variables exhibiting great influence on respondents’ perceptions. Whereas MLR findings show that being born in Malate and being part of a family household was the most significant regardless of socio-economic level and monthly household income. For the city officials, it was revealed that said lodgings are actually the second-highest earners in the City’s lodging industry. It was further stated that their zoning ordinance treats short-term accommodations just like any other lodging enterprise. So it’s perfectly legal for these establishments to situate themselves near residential areas and/or institutional structures. A sit down with barangays, on the other hand, recognized the economic benefits of short-term accommodations but likewise admitted that it contributes a negative place brand to the community. Lastly, real estate developers are amenable to having their projects built near short-term accommodations, for they do not have any bad views against it. They explained that their projects sites have always been motivated by suitability, liability, and marketability factors only. Overall, these findings merit a recalibration of the zoning ordinance and DOT Circular, as well as the imposition of regulations on their sexually suggestive roadside advertisements. Then, once relevant measures are refined for proper implementation, it can also pave the way for spatial interventions (like visual buffer corridors) to better address the needs of the locals, private groups, and government.

Keywords: estate planning, place brand, real estate development, short-term accommodations

Procedia PDF Downloads 165

Authors: Mumtaz Ali, Hamzullah Khan, Khalid Khanzada, Shahid Ayub, Aurangzeb Wazir

Abstract:

Objective: To analyse the death of patients treated in neuro-surgical ICU for severe head injuries from different perspectives. The evaluation of the data so obtained to help improve the health care delivery to this group of patients in ICU. Study Design: It is a descriptive study based on retrospective analysis of patients presenting to neuro-surgical ICU in Lady Reading Hospital, Peshawar. Study Duration: It covered the period between 1st January 2009 to 31st December 2009. Material and Methods: The Clinical record of all the patients presenting with the clinical radiological and surgical features of severe head injuries, who expired in neuro-surgical ICU was collected. A separate proforma which mentioned age, sex, time of arrival and death, causes of head injuries, the radiological features, the clinical parameters, the surgical and non surgical treatment given was used. The average duration of stay and the demographic and domiciliary representation of these patients was noted. The record was analyzed accordingly for discussion and recommendations. Results: Out of the total 112 (n-112) patients who expired in one year in the neuro-surgical ICU the young adults made up the majority 64 (57.14%) followed by children, 34 (30.35%) and then the elderly age group: 10 (8.92%). Road traffic accidents were the major cause of presentation, 75 (66.96%) followed by history of fall; 23 (20.53%) and then the fire arm injuries; 13 (11.60%). The predominant CT scan features of these patients on presentation was cerebral edema, and midline shift (diffuse neuronal injuries). 46 (41.07%) followed by cerebral contusions. 28 (25%). The correctable surgical causes were present only in 18 patients (16.07%) and the majority 94 (83.92%) were given conservative management. Of the 69 (n=69) patients in which CT scan was repeated; 62 (89.85%) showed worsening of the initial CT scan abnormalities while in 7 cases (10.14%) the features were static. Among the non surgical cases both ventilatory therapy in 7 (6.25%) and tracheostomy in 39 (34.82%) failed to change the outcome. The maximum stay in the neuro ICU leading upto the death was 48 hours in 35 (31.25%) cases followed by 31 (27.67%) cases in 24 hours; 24 (21.42%) in one week and 16 (14.28%) in 72 hours. Only 6 (5.35%) patients survived more than a week. Patients were received from almost all the districts of NWFP except. The Hazara division. There were some Afghan refugees as well. Conclusion: Mortality following the head injuries is alarmingly high despite repeated claims about the professional and administrative improvement. Even places like ICU could not change the out come according to the desired aims and objectives in the present set up. A rethinking is needed both at the individual and institutional level among the concerned quarters with a clear aim at the more scientific grounds. Only then one can achieve the desired results.

Keywords: Glasgow Coma Scale, pediatrics, geriatrics, Peshawar

Procedia PDF Downloads 350

Authors: Soroor Ghaziof, Wei Gao

Abstract:

Zn alloy and composite coatings are widely used in buildings and structures, automobile and fasteners industries to protect steel component from corrosion. In this paper, Zn-Ni-Al2O3 nano-composite coatings were electrodeposited on mild steel using a novel sol enhanced electroplating method. In this method, transparent Al2O3 sol was added into the acidic Zn-Ni bath to produced Zn-Ni-Al2O3 nano-composite coatings. The effect of alumina sol on the electrodeposition process, and coating properties was investigated using cyclic voltammetry, XRD, ESEM and Tafel test. Results from XRD tests showed that the structure of all coatings was single γ-Ni5Zn21 phase. Cyclic voltammetry results showed that the electrodeposition overpotential was lower in the presence of alumina sol in the bath, and caused the reduction potential of Zn-Ni to shift to more positive values. Zn-Ni-Al2O3 nano composite coatings produced more uniform and compact deposits, with fine grained microstructure when compared to Zn-Ni coatings. The corrosion resistance of Zn-Ni coatings was improved significantly by incorporation of alumina nano particles into the coatings.

Keywords: Zn-Ni-Al2O3 composite coatings, steel, sol-enhanced electroplating, corrosion resistance

Procedia PDF Downloads 393

Authors: Natalie Hoyer

Abstract:

Bridges in both roadway and railway systems depend on bearings to ensure extended service life and functionality. These bearings enable proper load distribution from the superstructure to the substructure while permitting controlled movement of the superstructure. The design of bridge bearings, according to Eurocode DIN EN 1337 and the relevant sections of DIN EN 1993, increasingly requires the use of thick plates, especially for long-span bridges. However, these plate thicknesses exceed the limits specified in the national appendix of DIN EN 1993-2. Furthermore, compliance with DIN EN 1993-1-10 regulations regarding material toughness and through-thickness properties necessitates further modifications. Consequently, these standards cannot be directly applied to the selection of bearing materials without supplementary guidance and design rules. In this context, a recommendation was developed in 2011 to regulate the selection of appropriate steel grades for bearing components. Prior to the initiation of the research project underlying this contribution, this recommendation had only been available as a technical bulletin. Since July 2023, it has been integrated into guideline 804 of the German railway. However, recent findings indicate that certain bridge-bearing components are exposed to high fatigue loads, which necessitate consideration in structural design, material selection, and calculations. Therefore, the German Centre for Rail Traffic Research called a research project with the objective of defining a proposal to expand the current standards in order to implement a sufficient choice of steel material for bridge bearings to avoid brittle fracture, even for thick plates and components subjected to specific fatigue loads. The results obtained from theoretical considerations, such as finite element simulations and analytical calculations, are validated through large-scale component tests. Additionally, experimental observations are used to calibrate the calculation models and modify the input parameters of the design concept. Within the large-scale component tests, a brittle failure is artificially induced in a bearing component. For this purpose, an artificially generated initial defect is introduced at the previously defined hotspot into the specimen using spark erosion. Then, a dynamic load is applied until the crack initiation process occurs to achieve realistic conditions in the form of a sharp notch similar to a fatigue crack. This initiation process continues until the crack length reaches a predetermined size. Afterward, the actual test begins, which requires cooling the specimen with liquid nitrogen until a temperature is reached where brittle fracture failure is expected. In the next step, the component is subjected to a quasi-static tensile test until failure occurs in the form of a brittle failure. The proposed paper will present the latest research findings, including the results of the conducted component tests and the derived definition of the initial crack size in bridge bearings.

Keywords: bridge bearings, brittle fracture, fatigue, initial crack size, large-scale tests

Procedia PDF Downloads 46