Search results for: hand kinematics

Authors: Siddeeq Y. Ameen, Mohammed K. Yousif

Abstract:

Cooperative communication systems are considered to be a promising technology to improve the system capacity, reliability and performances over fading wireless channels. Cooperative relaying system with a single antenna will be able to reach the advantages of multiple antenna communication systems. It is ideally suitable for the distributed communication systems; the relays can cooperate and form virtual MIMO systems. Thus the paper will aim to investigate the possible enhancement of cooperated system using decode and forward protocol. On decode and forward an attempt to cancel or at least reduce the interference instead of increasing the SNR values is achieved. The latter can be achieved via the use group of relays depending on the channel status from source to relay and relay to destination respectively. In the proposed system, the transmission time has been divided into two phases to be used by decode and forward protocol. The first phase has been allocated for the source to transmit its data whereas the relays and destination nodes are in receiving mode. On the other hand, the second phase is allocated for the first and second groups of relay nodes to relay the data to the destination node. Simulations results have shown an improvement in performance is achieved compared to the conventional decode and forward in terms of BER and transmission rate.

Keywords: cooperative systems, decode and forward, interference cancellation, virtual MIMO

Procedia PDF Downloads 321

Authors: Yulu Zhang, Atushi Teramoto, Taka-Aki Ohkubo

Abstract:

In this study, the effect of expansive additives on autogenous shrinkage and delayed expansion of ultra-high strength mortar was explored. The specimens made for the study were composed of ultra-high strength mortar, which was mixed with ettringite-lime composite type expansive additive. Two series of experiments were conducted with the specimens. The experimental results confirmed that the autogenous shrinkage of specimens was effectively decreased by increasing the proportion of the expansive additive. On the other hand, for the specimens, which had 7% expansive additive, and were cured for seven days at a constant temperature of 20°C, and then cured for a long time in either in an underwater, moist (Relative humidity: 100%) or dry air (Relative humidity: 60%) environment, excessively large expansion strain occurred. Specifically, typical turtle shell-like swelling expansion cracks were confirmed in the specimens that underwent long-term curing in an underwater and moist environment. According to the result of hydration analysis, the formation of expansive substances, calcium hydroxide and alumina, ferric oxide, tri-sulfate contribute to the occurrence of delayed expansion.

Keywords: ultra-high strength mortar, expansive additive, autogenous shrinkage, delayed expansion

Procedia PDF Downloads 237

Authors: Kevin D. Manalo, Jumelyn L. Torres, Noel B. Linsangan

Abstract:

This paper focuses on a wireless myoelectric prosthesis of the upper-limb that uses a Multilayer Perceptron Neural network with back propagation. The algorithm is widely used in pattern recognition. The network can be used to train signals and be able to use it in performing a function on their own based on sample inputs. The paper makes use of the Neural Network in classifying the electromyography signal that is produced by the muscle in the amputee’s skin surface. The gathered data will be passed on through the Classification Stage wirelessly through Zigbee Technology. The signal will be classified and trained to be used in performing the arm positions in the prosthesis. Through programming using Verilog and using a Field Programmable Gate Array (FPGA) with Zigbee, the EMG signals will be acquired and will be used for classification. The classified signal is used to produce the corresponding Hand Movements (Open, Pick, Hold, and Grip) through the Zigbee controller. The data will then be processed through the MLP Neural Network using MATLAB which then be used for the surface myoelectric prosthesis. Z-test will be used to display the output acquired from using the neural network.

Keywords: field programmable gate array, multilayer perceptron neural network, verilog, zigbee

Procedia PDF Downloads 387

Authors: Ting-Yu Hsu, Shyu-Yu Wu, Shieh-Kung Huang, Hung-Wei Chiang, Kung-Chun Lu, Pei-Yang Lin, Kuo-Liang Wen

Abstract:

Regional earthquake early warning (EEW) systems are not suitable for Taiwan, as most destructive seismic hazards arise due to in-land earthquakes. These likely cause the lead-time provided by regional EEW systems before a destructive earthquake wave arrives to become null. On the other hand, an on-site EEW system can provide more lead-time at a region closer to an epicenter, since only seismic information of the target site is required. Instead of leveraging the information of several stations, the on-site system extracts some P-wave features from the first few seconds of vertical ground acceleration of a single station and performs a prediction of the oncoming earthquake intensity at the same station according to these features. Since seismometers could be triggered by non-earthquake events such as a passing of a truck or other human activities, to reduce the likelihood of false alarms, a seismometer was installed at three different locations on the same site and the performance of the EEW system for these three sensor locations were discussed. The results show that the location on the ground of the first floor of a school building maybe a good choice, since the false alarms could be reduced and the cost for installation and maintenance is the lowest.

Keywords: earthquake early warning, on-site, seismometer location, support vector machine

Procedia PDF Downloads 240

Authors: Roman Girma Teshome

Abstract:

The intersection between development and human rights has been the point of scholarly debate for a long time. Consequently, a number of principles, which extend from the right to development to the human rights-based approach to development, have been adopted to understand the dynamics between the two concepts. Despite these attempts, the exact relationship between development and human rights has not been fully discovered yet. However, the inevitable interdependence between the two notions and the idea that development efforts must be undertaken by giving due regard to human rights guarantees has gained momentum in recent years. On the other hand, the emergence of sustainable development as a widely accepted approach in development goals and policies makes this unsettled convergence even more complicated. The place of sustainable development in human rights law discourse and the role of the latter in ensuring the sustainability of development programs call for a systematic study. Hence, this article seeks to explore the relationship between development and human rights, particularly focusing on the place given to sustainable development principles in international human right law. It will further quest whether there is a right to sustainable development recognized therein. Accordingly, the article asserts that the principles of sustainable development are directly or indirectly recognized in various human rights instruments, which provides an affirmative response to the question raised hereinabove. This work, therefore, will make expeditions through international and regional human rights instruments as well as case laws and interpretative guidelines of human rights bodies to prove this hypothesis.

Keywords: sustainable development, human rights, the right to development, the human rights-based approach to development, environmental rights, economic development, social sustainability

Procedia PDF Downloads 220

Authors: Moumen Souad, Melizi Mohamed

Abstract:

In order to characterize rabbits does of an Aures local population raised in Algeria, a study of their milk yield was realized in the experimental rabbitry of El Hadj Lakhdhar University. Milk production of does was measured every day during the days following 215 parturitions. It was estimated by weighing the female before and after the single daily suckling (10–15 min between the two weighing operations). The various calculated parameters were the quantity of milk produced per day, per week and the total quantity produced in 21 days, as well as the intake of milk by young rabbits. The analysis concerned the effects of the number of successive litters (3 classes: 1 to 3 and more) and of the average number of the number of young rabbits suckled per litter (6 classes: from 1-2 kits to more than 6). During the 21 days of controlled lactation, the average litter size was 6±3. The rabbits of the Aures area produced on average 2544.34±747 g in 21 days that is 121 g of milk/day or 21 g of milk/kit/day. The milk yield increased from 526, 1035, 1240 and 2801 g to 760, 1365, 1715 and 3840 for week 1, 2, 3 and the total period of lactation, respectively. Nevertheless, milk production available per kit and per day decreased linearly with kits number in the litter for each of the 3 weeks considered. On the other hand the milk yield was not affected by the weight at birth of kits.

Keywords: milk production, litter size, rabbit, Aures area, Algeria

Procedia PDF Downloads 260

Authors: Noemia Gomes de Mattos de Mesquita, José Eduardo Ferreira de Oliveira, Arimatea Quaresma Ferraz

Abstract:

Stops to exchange cutting tool, to set up again the tool in a turning operation with CNC or to measure the workpiece dimensions have a direct influence on production. The premature removal of the cutting tool results in high cost of machining since the parcel relating to the cost of the cutting tool increases. On the other hand, the late exchange of cutting tool also increases the cost of production because getting parts out of the preset tolerances may require rework for its use when it does not cause bigger problems such as breaking of cutting tools or the loss of the part. Therefore, the right time to exchange the tool should be well defined when wanted to minimize production costs. When the flank wear is the limiting tool life, the time predetermination that a cutting tool must be used for the machining occurs within the limits of tolerance can be done without difficulty. This paper aims to show how the life of the cutting tool can be calculated taking into account the cutting parameters (cutting speed, feed and depth of cut), workpiece material, power of the machine, the dimensional tolerance of the part, the finishing surface, the geometry of the cutting tool and operating conditions of the machine tool, once known the parameters of Taylor algebraic structure. These parameters were raised for the ABNT 1038 steel machined with cutting tools of hard metal.

Keywords: machining, productions, cutting condition, design, manufacturing, measurement

Procedia PDF Downloads 632

Authors: Aurélie Cassiers

Abstract:

In this presentation, an overview is given of the freedom of states to legislate concerning abortion. Today, access to safe and legal abortion is still a hot topic in many countries in the world. Abortion policies try to strike a balance between women’s rights to self-determination and private life on the one hand, and the protection of the life of unborn children on the other. Each country has different religious, cultural and political views on abortion, and therefore specific legislations. However, citizens may submit a complaint at international courts when they find their national legislation too restrictive. The study is discussed of the development of the ECtHR, UNCHR, and IACHR case law, regarding the question of the ‘right to abort’ and indirectly of the protection of the unborn children. Each relevant case is analyzed to answer the following questions: Is the unborn child protected, and if so, how? Why does the woman want to abort and how is her interest or right protected? How is a fair balance reached between the different interests? Is the state completely free to write policies that restrict abortion? What are the factors to determine the margin of appreciation of the state? In conclusion, does this specific court recognize a right to abort, and if so, under which conditions? To conclude, this presentation shows that each court has its own perspective on and perception of abortion, and its own criteria to determine whether the state is complying with international norms regarding individual liberty and protection of the children.

Keywords: abortion, international courts, unborn children, women rights

Procedia PDF Downloads 128

Authors: Dina Helmy El-Ghonemy, Thanaa Hamed Ali

Abstract:

The aim of this study was to purify and characterize a keratinolytic enzyme produced by Aspergillus sp. DHE7 cultured in basal medium containing chicken feather as substrate. The enzyme was purified through ammonium sulfate saturation of 60%, followed by gel filtration chromatography in Sephadex G-100, with a 16.4-purification fold and recovery yield of 52.2%. Sodium dodecyl sulfate-polyacrylamide gel electrophoresis revealed that the purified enzyme is a monomeric enzyme with an apparent molecular mass of 30 kDa — the purified keratinase of Aspergillus sp. DHE7 exhibited activity in a broad range of pH (7- 9) and temperature (40℃-60℃) profiles with an optimal activity at pH eight and 50℃. The keratinolytic activity was inhibited by protease inhibitors such as phenylmethylsulfonyl fluoride and ethylenediaminetetraacetate, while no reduction of activity was detected by the addition of dimethyl sulfoxide (DMSO). Bivalent cations, Ca²⁺ and Mn²⁺, were able to greatly enhance the activity of keratinase by 125.7% and 194.8%, respectively, when used at one mM final concentration. On the other hand, Cu²⁺ and Hg²⁺ inhibited the enzyme activity, which might be indicative of essential vicinal sulfhydryl groups of the enzyme for productive catalysis. Furthermore, the purified keratinase showed significant stability and compatibility against the tested commercial detergents at 37ºC. Therefore, these results suggested that the purified keratinase from Aspergillus sp. DHE7 may have potential use in the detergent industry and should be of interest in the processing of poultry feather waste.

Keywords: Aspergillus sp. DHE7, biochemical characterization, keratinase, purification, waste management

Procedia PDF Downloads 123

Authors: Ferruh Taspinar, Gulce K. Seyyar, Gamze Kurt, Eda O. Okur, Emrah Afsar, Ismail Saracoglu, Betul Taspinar

Abstract:

Overweight and obesity has been associated with postural balance. The aim of this study was to investigate the relationship between body composition and balance. One hundred and thirty two young adults (58 male, 74 female) were included in the study. Mean age of participants were found as 21.21±1.51 years. Body composition (body mass index, total body fat ratio, total body muscle ratio) and balance (right anterior, right postero-medial, right postero-lateral, left anterior, left postero-medial, left postero-lateral) were evaluated by Tanita BC-418 and Y balance test, respectively. Pearson correlation analysis was used to evaluate the correlation between the parameters. Significance level in statistical analysis was accepted as 0.05. According to results, no correlation was found between body mass index and balance parameters. There was negative correlation between total body fat ratio and balance parameters (r=0.419-0.509, p˂0.05). On the other hand, positive correlation was found between total body muscle ratio and balance parameters (r=0.390-0.494, p˂0.05). This study demonstrated that body fat and muscle ratio affects the balance. Body composition should be considered in rehabilitation programs including postural balance training.

Keywords: balance, body composition, body mass, young adults

Procedia PDF Downloads 371

Authors: Ozlem Temiz-Arpaci, Meryem Tasci, Fatma Sezer Senol, İlkay Erdogan Orhan

Abstract:

Alzheimer’s disease (AD), a neurodegenerative disorder characterized by a progressive deterioration of memory and cognition, occurs more frequently in elderly people. Current treatment approaches in this disease with the major therapeutic strategy are based on the AChE and BChE inhibition. On the other hand, tyrosinase inhibition has become a target for the treatment of Parkinson’s disease (PD) since this enzyme may play a role in neuromelanin formation in the human brain and could be critical in the formation of dopamine neurotoxicity associated with neurodegeneration linked to PD. Also benzoxazoles are structural isosteres of natural nucleotides that can interact with biopolymers so that benzoxazoles showed a lot of different biological activities. In this study, a series of 2,5-disubstituted-benzoxazole derivatives were synthesized and were evaluated as possible inhibitors of acetylcholinesterase (AChE) / butyrylcholinesterase (BChE) and tyrosinase. The results demonstrated that the compounds exhibited a weak spectrum of AChE / BChE inhibitory activity ranging between 3.92% - 54.32% except compound 8 which showed no activity against AChE and compound 4 which showed no activity against BChE at the specified molar concentrations. Also, the compounds indicated lower than tyrosinase inhibitory activity of ranging between 8.14% - 22.90% to that of reference (kojic acid).

Keywords: AChE and BChE inhibition, Alzheimer’s disease, benzoxazoles, tyrosinase inhibition

Procedia PDF Downloads 340

Authors: Mojtaba Heydarizad

Abstract:

Khorasan Razavi is the second most important province in north-east of Iran, which faces a water shortage crisis due to recent droughts and huge water consummation. Kardeh and Torogh dam reservoirs in this province provide a notable part of Mashhad metropolitan (with more than 4.5 million inhabitants) potable water needs. Hydrochemical analyses on these dam reservoirs samples demonstrate that MgHCO₃ in Kardeh and CaHCO₃ and to lower extent MgHCO₃ water types in Torogh dam reservoir are dominant. On the other hand, Gibbs binary diagram demonstrates that rock weathering is the main factor controlling water quality in dam reservoirs. Plotting dam reservoir samples on Mg²⁺/Na⁺ and HCO₃^-/Na⁺ vs. Ca²⁺/ Na⁺ diagrams demonstrate evaporative and carbonate mineral dissolution is the dominant rock weathering ion sources in these dam reservoirs. Cluster Analyses (CA) also demonstrate intense role of rock weathering mainly (carbonate and evaporative minerals dissolution) in water quality of these dam reservoirs. Studying water quality by the U.S. National Sanitation Foundation (NSF) WQI index NSF-WQI, Oregon Water Quality Index (OWQI) and Canadian Water Quality Index DWQI index show moderate and good quality.

Keywords: hydrochemistry, water quality classification, water quality indexes, Torogh and Kardeh dam reservoir

Procedia PDF Downloads 253

Authors: Tanvir Ahmed, Thanh N. Long, Phan T. Huong, Donald E. Stewart

Abstract:

This paper presents views on condom use and the contexts of safe and unsafe sexual practices with different sexual partners and their relationships among Injecting Drug Users (IDUs) in Hai Phong, Vietnam. Fifteen IDUs participated and two local interviewers conducted qualitative semi-structured face-to-face interviews in September-October, 2012 in Vietnamese language. Data were analyzed thematically. Non-protective condom attitudes include negotiate or convince Female Sex Workers (FSW); not realizing risk, importance or necessity; partner doesn’t like, and having extra money/drug from clients. On the other hand, self-awareness, family-consciousness, suspicion of STI presence, fear of getting HIV, and client negotiation sometimes resulted in a safe-sex practice. A thematic diagram was developed to present the relationship (strong/weak) between condom attitude and sexual practice (safe/unsafe) by partner types. The experiences and views reflected in the qualitative information emphasize the heightened need for safe-sex education especially among young IDUs (male/female) highlighting sexual transmission risk.

Keywords: AIDS, HIV, injecting drug user, risk behaviors, Vietnam

Procedia PDF Downloads 856

Authors: Medalson Ronghang, Pranjal Barman, Heemantajeet Medhi

Abstract:

Bank filtration (BF) being a natural method of abstracting surface water from the river or lake via sub-surface. It can be intensively used and operated under various operating conditions for sustainability. Field investigations were carried out at various location of Kokrajhar (Assam) and Srinagar (Uttarakhand) to assess the ground water and their bank filtration wells to compare and characterized the quality. Results obtained from the analysis of the data suggest that major water quality parameter were much below the drinking water standard of BIS 10500 (2012). However, the iron concentration was found to be more than permissible limit in more than 50% of the sampled hand pump; the concentration ranged between 0.33-3.50 mg/L with acidic in nature (5.4 to 7.4) in Kokrajhar and high nitrate in Srinagar. But the abstracted water from the RBF wells has attenuated water quality with no iron concentration in Kokrajhar. The aquifers and riverbed material collected along the bank of Rivers Gaurang and Alaknanda were sieved and classified as coarse silt to medium gravel. The hydraulic conductivity was estimated in the range 5×10⁻³ to 1.4×10⁻²- 3.09×10⁻⁴-1.29 ×10⁻³ for Kokrajhar and Srinagar respectively suggesting a good permeability of the aquifer. The maximum safe yield of the well was estimated to be in the range of 4000 to 7500 L/min. This paper aims at demonstrating bank filtration method as an alternative to mineralized groundwater for drinking water.

Keywords: Riverbank filtration, mineralization, water quality, groundwater

Procedia PDF Downloads 217

Authors: Maryam Khalili, Fateme Ghanei

Abstract:

As one of the most significant phenomena of industrialized societies, tourism plays a key role in encouraging regional developments and enhancing higher standards of living for local communities in particular. Traveling is a formative experience endowed with lessons on various aspects of life. It allows us learning how to enhance the social position as well as the social relationships. However, people forget the need to travel and gain first-hand experiences as they have to cope with the ever-increasing rate of stress created by the disorders and routines of the urban dwelling style. In this paper, various spaces of such experiences were explored through a virtual tour with two underlying aims: 1) encouraging, informing, and educating the community in terms of tourism development, and 2) introducing a temporary release from the routines. This study enjoyed a practical-qualitative research methodology, and the required data were collected through observation and using a multiple-response questionnaire. The participants (19-48 years old) included 41 citizens of both genders (63.4% male and 36.6% female) from two regions in Tehran, selected by cluster-probability sampling. The results led to development of a spatial design for a virtual tour experience in Tehran where different areas are explored to both raise people’s awareness and educate them on their cultural heritage.

Keywords: ecotourism, education, gamification, social interaction, urban design, virtual tour

Procedia PDF Downloads 188

Authors: Sihem Chaibeddra, Fatoum Kharchi

Abstract:

This study deals with the characterization of stabilized earth in the field of construction from the behavior under changes in conservation conditions that may occur during the lifetime of the material, namely, the exposure to high humidity and temperature variations. These two parameters are involved increasingly, because of climate changes that are confronting earth-based constructions to conditions for which they were not originally designed. These exposure conditions may affect the long-term behavior of the material and the entire structure. A cement treatment was adopted for stabilizing the earth with dosages ranging from 4, 6, 8 to 10%. The influence of addition percentage was analyzed in this context based on laboratory tests measuring the evolution of compressive strength, rate of absorption and shrinkage, and finally thermal conductivity. It was shown that the behaviour was dependent on the ambient conditions which influence the action of the binder. Temperate cure has proved beneficial for the material as the cement content increased. Moisture has less affected the compressive strength with increasing the cement content. The absorption was reduced with the increase of cement dosage. Regarding the variation of shrinkage, cement assays have presented an optimum value beyond which the addition of further quantities was less advantageous. The thermal conductivity on the other hand, increased with increasing cement content, which decreased the insulating properties of the material.

Keywords: behavior, characterization, construction, earth, stabilization

Procedia PDF Downloads 242

Authors: Maryam Hoorzad, Narges Shokry, Mandan Momeni

Abstract:

According to importance of socialization in effectiveness of organizations and on the other hand assessing the impact of individual differences on socialization tactics by measuring employees satisfaction, can be assessed for each of the personality types which socialization tactics is the more effective. The aim of this paper is to investigate how organizational socialization tactics affect job satisfaction of employees according to personality types. A survey was conducted using a measurement tool based on Van Maanen and Schein’s theory on organizational socialization tactics and Myers Briggs’ measurement tools of personality types. The respondents were employees with more than 3 years backward in Tehran University of Medical Science. Data collection was performed using both library and field, the data collection instrument was questionnaires and data were analysed using the Spss and Lisrel programs. It was found that investiture and serial tactics has a significant effect on employees satisfaction, any increase in investiture and serial tactics led to increase in job satisfaction and any increase in divestiture and disjunctive tactics led to reduction of job satisfaction. Investiture tactic has the most effect on employees satisfaction. Also based on the results, personality types affect the relationship between socialization tactics and job satisfaction. In the ESFJ personality type the effect of investiture tactic on employee satisfaction is the most.

Keywords: organizational socialization, organizational socialization tactics, personality types, job satisfaction

Procedia PDF Downloads 439

Authors: Andy Obinna Ibeje

Abstract:

In this study, the erodibility indices and some soil properties of some cassava farms in selected areas of Abia and Imo States were investigated. This study involves taking measurements of some soil parameters such as permeability, soil texture and particle size analysis from which the erodibility indices were compared. Results showed that soils of the areas are very sandy. The results showed that Isiukwuato with index of 72 has the highest erodibility index. The results also showed that Arondizuogu with index of 34 has the least erodibility index. The results revealed that soil erodibility (k) values varied from 34 to 72. Nkporo has the highest sand content; Inyishie has the least silt content. The result indicates that there were respectively strong inverse relationship between clay and silt contents and erodibility index. On the other hand, sand, organic matter and moisture contents as well as soil permeability has significantly high positive correlation with soil erodibility and it can be concluded that particle size distribution is a major finger print on the erodibility index of soil in the study area. It is recommended that safe cultural practices like crop rotation, matching and adoption of organic farming techniques be incorporated into farming communities of Abia and Imo States in order to stem the advances of erosion in the study area.

Keywords: erodibility, indices, soil, sand

Procedia PDF Downloads 344

Authors: Panyarat Panthong

Abstract:

This research paper was conducted to examine the association between demographic, professional and social characteristics, and self-leadership of personnel who worked at Sub-District Administrative Organization Offices in Muang District, Udon Thani Province, and to identify the degree level of self-leadership of the selected samples in relation with the study variables. A total of 89 samples were collected from the 15 Sub-District Administrative Organization Offices. The paper employed both quantitative and qualitative methods using the Chi- Square and Cramer’s V statistics for the data analysis. The findings unveiled that constructive thought strategies showed a significant existence followed by behavior- focused strategies and natural reward strategies. Moreover, the research found that the respondents’ length of time working in the position and the respondents’ self- leadership presented a significant association in terms of the behavior-focused and constructive thought strategies. On the other hand, the respondents’ demographic characteristics placed no association with the level of self-leadership in behavior-focused strategies, natural reward strategies and constructive thought strategies. It is hoped that this finding will provide informative and practical guidance for the Ministry of Interior of Thailand and Department of Local Administration of the studied province.

Keywords: demographic characteristics, professional characteristics, self- leadership, social characteristics

Procedia PDF Downloads 423

Authors: Samir Roy

Abstract:

This paper investigates the relationship among knowledge, technology, and empowerment. In Physics power is defined as rate of doing work. In everyday use, the meaning of the word power is related to the capacity to bring change of value in the world. It appears that the popular aphorism “Knowledge is power” should be revisited in the context of contemporary states of affairs. For instance, classical mechanics is a system of knowledge, so also thermodynamics. But neither of them, per se, is sufficient to produce automobilin es. Boolean algebra, the logical foundation of digital electronic computers, was introduced by George Boole in 1847. But that knowledge was practically useless for almost one hundred years until digital electronics was developed in early twentieth century, which eventually led to invention of digital electronic computers. Empowerment of women is a burning issue in the arena of social justice. However, if we carefully analyze the functional elements of women’s empowerment, we find them to be highly technology driven as well as technology dependent in real life. On the other hand, technology has empowered modern states to maintain social order and promote democracy in an effective manner. This paper includes a few case studies to establish the close correspondence between knowledge, especially scientific knowledge, technology, and empowerment. It appears that in contemporary scenario, “Technology is power” is a more appropriate statement than the traditional aphorism “Knowledge is power”.

Keywords: knowledge, science, technology, empowerment, change, social justice

Procedia PDF Downloads 39

Authors: Lila Boulekbache-Makhlouf, Brahmi Fatiha

Abstract:

This study was carried out with the aim of enriching fresh cheese with the food by-products, which are the leaves of shallots and the peels of potatoes. Firstly, the conditions for extracting the total polyphenols (TPP) using ultrasound are optimized. Then, the contents of PPT, flavonoids, and antioxidant activity were evaluated for the extracts obtained by adopting the optimal parameter. On the other hand, we have carried out some physico-chemical, microbiological, and sensory analyzes of the cheese produced. The maximum PPT value of 70.44 mg GAE/g DM of shallot leaves was reached with 40% (v/v) ethanol, an extraction time of 90 min, and a temperature of 10°C. Meanwhile, the maximum TPP content of potato peels of 45.03 ± 4.16 mg GAE/g DM was obtained using an ethanol/water mixture (40%, v/v), a time of 30 min, and a temperature of 60°C and the flavonoid contents were 13.99 and 7.52 QE/g DM, respectively. From the antioxidant tests, we deduced that the potato peels present a higher antioxidant power with IC50s of 125.42 ± 2.78 μg/mL for DPPH, of 87.21 ± 7.72 μg/mL for phosphomolybdate and 200.77 ± 13.38 μg/mL for iron chelation, compared with the results obtained for shallot leaves which were 204.29 ± 0.09, 45.85 ± 3,46 and 1004.10 ± 145.73 μg/mL, respectively. The results of the physico-chemical analyzes have shown that the formulated cheese was compliant with standards. Microbiological analyzes show that the hygienic quality of the cheese produced was satisfactory. According to the sensory analyzes, the experts liked the cheese enriched with the powder and pieces of the leaves of the shallots.

Keywords: shallots leaves, potato peels, ultrasound extraction, phenolic, cheese

Procedia PDF Downloads 183

Authors: Rabah Laouar, Yahia Boudra, Adel Satouh, Adrian Boyce

Abstract:

The ultramafic rocks of the Collo region crop out as « stratified » masses that cross-cut older metamorphic formation of the basement. These rocks are mainly peridotites and serpentinites. The peridotites are composed of olivine, orthopyroxene, clinopyroxene and spinel (chromite). The chemical composition of these lherzolites show a magnesian character with high MgO contents (34.4 to 37.5%), high Cr (0.14 to 0.27%), Ni (0.14 to 0.26%) and Co (34 to 133 ppm) and low CaO and Al₂O₃ (0.02 to 2.2 and 0.5 to 2.8 % respectively). They represent a residue (restite) of a mantle magmas partial melting. The chromite which represents about 2 to 3% of the rock is a ubiquitous mineral and shows two different generations: primary idiomorphic millimetric crystals and secondary very fine, xenomorphic and interstitial aggregates. The primary chromites are alumino-ferro-magnesian crystals. They show high Al₂O₃ (25.77% to 27.36%) and MgO (10.70% to 13.36%). Cr# (100*Cr/ (Al+Cr)) varies between 45 and 48, and Mg# (100*Mg/Mg+Fe₂+) varies between 49 and 59. On the other hand, the secondary interstitial grains are iron-rich chromites; they show low Al₂O₃ (4.67% to 9.54%) and MgO (4.60% to 4.65%). Cr# is relatively high (77 to 88) whereas Mg# show relatively low values, varying between 22 and 25. Oxygen isotopic composition of both types of chromites is consistent with their derivation from a mantle source (ð¹⁸O vary between +3.9 and +5.2‰), though a contribution of ¹⁶O-rich component to the secondary chromites is not ruled out.

Keywords: peridotites, serpentinites, chromite, partial melting, collo, Algeria

Procedia PDF Downloads 87

Authors: Camilo Perez Lee, Mark Lefsrud, Edris Madadian, Yves Roy

Abstract:

Biomass availability is one of the most important aspects to consider when determining the proper location of potential bioenergy plants. Since this aspect has a direct impact on biomass transportation and storage, biomass availability greatly influences the operational cost. Biomass availability is more than the quantity available on a specific region; other elements such as biomass accessibility and potential play an important role. Accessibility establishes if the biomass could be extracted and conveyed easily considering factors such as biomass availability, infrastructure condition and other operational issues. On the other hand, biomass potential is defined as the capacity of a specific region to scale the usage of biomass as an energy source, move from another energy source or to switch the type of biomass to increase their biomass availability in the future. This paper defines methodologies and parameters in order to determine the biomass availability within the administrative regions of the province of Quebec; firstly by defining the forestry, agricultural, municipal solid waste and energy crop biomass availability per administrative region, next its infrastructure accessibility and lastly defining the region potential. Thus, these data are processed to create a biomass availability matrix allowing to define the overall biomass availability per region and to determine the most optional candidates for bioenergy plant location.

Keywords: biomass, availability, bioenergy, accessibility, biomass potential

Procedia PDF Downloads 316

Authors: Ayman Hassouna

Abstract:

Gaza was famous in the history of trade, because it lies at the end of overland trade route, then the goods transferred by Gazzian merchants to different places around the Mediterranean, so it is described as ‘Mediterranean port of Arabs’, but Gaza is not located directly at the sea shore, so it is fortified by two ports: the first is Anthedon, and second is Maiomas. It is possible to dig in Anthedon but it is too difficult to do that in Maiomas because the site is full of modern buildings. Archaeological excavations at Anthedon's port provided us much archaeological and historical information about cooperation between Anthedon's port and different places at the Mediterranean basin. This research speaks about the roots of Anthedon's name, and it is related with other names in Greek land, by use different dictionaries language, and produce historical introduction were covering the ages beginning from the Iron Age to Greek, Roman and Byzantine periods. Then the study reviewed the most important architectural discoveries in the site, and highlighted the relationship with the civilizations' ports of the Mediterranean basin by studying number of artefacts pottery were imported from different places as Cyprus, Greece, Italy, North Africa, Carthage and Tripoli workshops. On the other hand, the archaeologists discovered some of local pottery made in Gaza at different sites on the Mediterranean basin which confirms the relationship of Gaza merchants with those areas. At the end of this study, there are some conclusions and recommendations about the site.

Keywords: ancient port of Gaza, pottery typology, Mediterranean basin ports, Palestine archaeology

Procedia PDF Downloads 356

Authors: Minho Kwon, Seonghyeok Lee, Wooyoung Jung

Abstract:

In recent years, with increase of construction of skyscraper structures, the study of concrete materials to improve their weight and performance has been emerging as a key of research area. Typically, the concrete structures has disadvantage of increasing the weight due to its mass in comparison to the strength of the materials. Therefore, in order to improve such problems, the light-weight aggregate concrete and high strength concrete materials have been studied during the past decades. On the other hand, the study of light-weight aggregate concrete materials has lack of data in comparison to the concrete structure using high strength materials, relatively. Consequently, this study presents the performance characteristics of light-weight aggregate concrete materials due to the material properties and strength. Also, this study conducted the experimental tests with respect to normal and lightweight aggregate materials, in order to indentify the tensile crack failure of the concrete structures. As a result, the Crack Mouth Opening Displacement (CMOD) from the experimental tests was constructed and the fracture energy using inverse problem analysis was developed from the force-CMOD relationship in this study, respectively.

Keywords: lightweight aggregate concrete, crack mouth opening displacement, inverse analysis, fracture energy

Procedia PDF Downloads 355

Authors: Syahidah N. Zulkifli, Herlina A. Rahim, Nurul A. M. Subha

Abstract:

Sustaining water quality is critical in order to avoid any harmful health consequences for end-user consumers. The detection of microbial impurities at the household level is the foundation of water security. Water quality is now monitored only at water utilities or infrastructure, such as water treatment facilities or reservoirs. This research provides a first-hand scientific understanding of microbial composition presence in Malaysia’s household point-of-use (POUs) water supply influenced by seasonal fluctuations, standstill periods, and flow dynamics by using the NIR-Raman spectroscopic technique. According to the findings, 20% of water samples were contaminated by pathogenic bacteria, which are Legionella and Salmonella cells. A comparison of the spectra reveals significant signature peaks (420 cm⁻¹ to 1800 cm⁻¹), including species-specific bands. This demonstrates the importance of regularly monitoring POUs water quality to provide a safe and clean water supply to homeowners. Conventional Raman spectroscopy, up-to-date, is no longer suited for real-time monitoring. Therefore, this study introduced an alternative micro-spectrometer to give a rapid and sustainable way of monitoring POUs water quality. Assessing microbiological threats in water supply becomes more reliable and efficient by leveraging IoT protocol.

Keywords: microbial contaminants, water quality, water monitoring, Raman spectroscopy

Procedia PDF Downloads 108

Authors: Yassir AbdelRazig, Eren Ozguven, Ren Moses

Abstract:

While there exists a greater understanding of the differences between the driving behaviors of older and younger drivers, there is still a need to further understand how the two groups perform when attempting to perform complex intersection maneuvers. This paper looks to determine if, and to what extent, these differences exist when drivers encounter permissive left-hand turns, pedestrian traffic, two and four-lane intersections, heavy fog, and night conditions. The study will utilize a driving simulator to develop custom drivable scenarios containing one or more of the previously mentioned conditions. 32 younger and 32 older (+65 years) participants perform driving simulation scenarios and have their velocity, time to the nearest oncoming vehicle, accepted and rejected gaps, etc., recorded. The data collected from the simulator is analyzed via Raff’s method and logistic regression in order to determine and compare the critical gaps values of the two cohorts. Out of the parameters considered for this study, only the age of the driver, their experience (if they are a younger driver), the size of a gap, and the presence of pedestrians on the crosswalk proved significant. The results did not support the hypothesis that older drivers would be significantly more conservative in their critical gaps judgment and acceptance.

Keywords: older drivers, simulation, left-turn, human factors

Procedia PDF Downloads 246

Authors: Girish Choudhary

Abstract:

Education is in a state of flux. Not only one need to acquire skills in order to cope with a fast changing global world, an explosive growth in technology, on the other hand is providing a new wave of teaching tools - computer aided video instruction, hypermedia, multimedia, CD-ROMs, Internet connections, and collaborative software environments. The emerging technology incorporates the group qualities of interactive, classroom-based learning while providing individual students the flexibility to participate in an educational programme at their own time and place. The technology facilitating self learning also seems to provide a cost effective solution to the dilemma of delivering education to masses. Online education is a unique learning domain that provides for many to many communications as well. The computer conferencing software defines the boundaries of the virtual classroom. The changing paradigm provides access of instruction to a large proportion of society, promises a qualitative change in the quality of learning and echoes a new way of thinking in educational theory that promotes active learning and open new learning approaches. Putting it to practice is challenging and may fundamentally alter the nature of educational institutions. The subsequent part of paper addresses such questions viz. 'Do we need to radically re-engineer the curriculum and foster an alternate set of skills in students?' in the onward journey.

Keywords: on-line education, self learning, energy and power engineering, future education

Procedia PDF Downloads 328

Authors: Edgard Gnansounoua, Pavel Vaskan, Elia Ruiz Pachón

Abstract:

This work addresses the economic and environmental performance of integrated biorefineries based on sugarcane juice and residues in the context of Brazil. We have considered four multiproduct scenarios; two from existing Brazilian sugar mills and the others from ethanol autonomous distilleries. They are integrated biorefineries producing first (1G) and second (2G) generation ethanol, sugar, molasses (for animal feed) and electricity. We show the results for the analysis and comparison of the different scenarios using a techno-economic value-based approach and LCA methodology. We have found that all the analysed scenarios show positive values of Climate change and Fossil depletion reduction as compared to the reference systems. However the scenario producing only ethanol shows less efficiency in Human toxicity, Freshwater ecotoxicity and Freshwater eutrophication impacts. The best economic configuration is provided by the scenario with the largest ethanol production. On the other hand, the best environmental performance is presented by the scenario with full integration sugar – 1G2G ethanol production. The integration of 2G based residues in a 1G ethanol production plant leads to positive environmental impacts compared to the conventional 1G industrial plant but proves to be more expensive.

Keywords: sugarcane, biorefinery, 1G/2G bioethanol integration, LCA, Brazil

Procedia PDF Downloads 349

Authors: Mehrnoosh Pirhayati

Abstract:

Translation can be affected by different meta-textual factors of target context such as ideology, politics, and culture. So, the rule of fidelity, or being faithful to the source text, can be ignored by the translator. On the other hand, critical discourse analysis, derived from applied linguistics, is entered into the field of translation studies and used by scholars for revealing hidden deviations and possible roots of manipulations. This study focused on the famous Persian translation of the bestseller book, “A**hole No More,” written by XavierCrement 1990, performed by Mahmud Farjami to comparatively and critically analyze it with its corresponding English original book. The researcher applied Pirhayati’s model and framework of translation criticism at the textual and semiotic levels for this qualitative study. It should be noted that Kress and Van Leeuwen’s semiotic model, along with Machin’s model of typographical analysis, was also used at the semiotic level. The results of the comparisons and analyses indicate thatthis Persian translation of the book is affected by the factors of ideology and economics and reveal that the Islamic attitude causes the translator to employ some strategies such as substitution and deletion. Those who may benefit from this research are translation trainers, students of translation studies, critics, and scholars.

Keywords: farjami (2013), Ideology, manipulation, pirhayati's (2013) model of translation criticism, Xavier crement (1990)

Procedia PDF Downloads 212